Dixon Lawn Mower ZTR 311 User Manual

DATE 8/86 Re  
PAGE 1 of 6  
TECHNICAL DATA BROCHURE - ZTR 308 & 311  
IMPORTANT  
-
READ OPERATOR'S MANUAL BEFORE OPERATING OR MAKING ADJUSTMENTS.  
Seat Adjustment  
Loosen bolts on sliding brackets under each side of the seat, slide seat forward or rearward to  
desired position. Tighten bolts. Do not operate the mower with bracket bolts in "loose"  
condition.  
Mower Blade Operation  
To engage the mower blades, turn lever on floor, slowly, to the "ON" position. To disengage  
mower blades, turn lever, slowly, to the "OFF" position.  
Removing The Body  
1. Disconnect Throttle cable from engine.  
2. Disconnect the wiring loom from the body by turning the threaded collar on the connector in a  
counterclockwise direction. This connector is located at the left rear of the body.  
3. Remove four control lever bolts, and remove upper control levers, (P/N 9079 & 9080).  
4. Remove the two attach nuts on the floor of the body and release the latches on the rear of  
the body, near each side.  
5. Place height adjustment lever in the vertical position, and mower deck engaging lever in  
(
the "OFF" position. Carefully lift the body off the chassis.  
6. For assembly, reverse the procedure.  
Removing The Mower Deck  
1. Loosen the belt keeper, (P/N 2294), located under the engine by loosening two rear engine  
mounting bolts, allowing the deck drive belt to come free of the rear pulley. Tighten the belt  
keeper.  
2. Disconnect the wiring loom at the deck safety switch, (P/N 4242).  
3. Remove four attach pins, (P/N 6107) and clips, (P/H 3072) from the deck attach points and  
stabilizer bars.  
4. Lift the front of the mower chassis clear of the deck engaging rod, (P/N 2686). Roll the chassis free  
of the deck.  
5. 'To install, reverse the procedure.  
Adjustment Of Mower Deck Drive Belt  
1. Disengage the mower deck drive belt.  
2. To obtain the proper belt tension, loosen lock nut, (P/N 3005) and rotate engaging rod '  
linkage, (P/N 3607).  
3. After making an adjustment, engage the drive belt and check the tension. (The proper •  
tension for an engaged V-belt is the lowest tension at which the belt will not slip under  
normal load conditions.)  
4. If further adjustment is necessary, repeat steps 1 through 3, until proper adjustment is  
achieved.  
5. After the belt tension is adjusted, check to assure that the mower blade will not turn  
freely when the engaging rod is in the "OFF" position.  
6. If the mower blade turns freely, adjust the blade brake using swivel fitting, (P/N 2172), located  
on the brake linkage "L" rod, (P/N 2841) so that there is 1/8" to 1/4" gap between the deck safety  
switch body, (P/N 4242), and the striker plate, attached to the clutch idler bracket, (P/N 2847),  
when the brake is engaged.  
NOTE: The clutch idler bracket, (P/N 2847) must be raised so that the brake link swivel, (P/N 2172) can  
be adjusted.  
7. After adjustment is achieved, perform the safety checks listed below.  
"IMPORTANT" - Perform SAFETY CHECKS after making any repairs or adjustments.  
1. After reassembly, while seated on the mower, attempt to start the engine with the mower deck  
engaged. Engine should not start. If engine does start, return the mower to an Authorized Dixon  
Dealer for adjustment or repair.  
2. Disengage the mower deck and start engine. With the operator in the normal seated position, engage  
mower deck and remove weight from the seat. The engine should stop. If the engine doesn't stop when  
operator rises from the seat, return the mower to an Authorized Dixon Dealer for adjustment or  
repair.  
3. Engage, then disengage, mower blade in each cutting height. Insure that blade disengages and comes  
to a stop within 5 seconds in each height position. If blade does not disengage properly, repeat  
belt adjustment procedure or contact your Authorized Dixon Dealer.  
Removing The Mower Blade  
Secure the blade, (P/N 6013) from turning. (Observe the blade position when removing.) Remove  
the blade bolt from the center of the blade, remove the blade flange, (P/N 2837), blade, (P/N 2406),  
and spacer, (P/N 2829).  
WARNING:  
Sharp edges on the blade can cause injury! Caution should be e x e r c i s e d when s e r v i c e  
is required on the blade.  
Parking Brake Adjustment  
Remove the body as described above. Tighten nut on brake rod, (P/N 2533), (Located in front of  
the transaxle on each side), just enough to prevent brake from slipping when engaged.  
CAUTION; Over-tightening may cause premature wear on the brake band, (P/N 5085).  
P/N 8603  
OIXON INDUSTRIES, INC.  
Box 494  
Coffeyville, Kansas 67337-0494  
(316) 251-2000  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CHASSIS ASSEMBLY (MODEL 308 & 311)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRANSAXLE ASSEMBLY (MODEL 308 & 311)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MOWER DECK (MODEL ZTR 308 & 311)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4211 SOLENOID STARTER  
GABLE 4517 SHORT  
BODY WIRING LOOM - 4484  
REAR WIRING LOOM-4495  
WIRING KIT (308-311)-8669  
(SEE ASSEMBLY BREAKDOWN)  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Clarion Cassette Player AX410 User Manual
Country Flame Indoor Fireplace CF 04 User Manual
Crown Audio Stereo Amplifier 1160MA User Manual
Cub Cadet Lawn Mower 1210 680 User Manual
Cuisinart Blender HFP 300 User Manual
CyberData Network Card Wireless IP Pendant User Manual
Delta Electronics Power Supply HCB1047B User Manual
Edelbrock Automobile Parts Pro Flo Multi Point User Manual
Electro Voice Stereo Amplifier L 1000 User Manual
Euro Pro Carpet Cleaner SC926H User Manual