Installation and Operating Instructions
Passive Infra-Red Detector Switch
Model No. DX4130
Issue 3 November 2006
Height
Width
Depth
130mm
85mm
145mm
130mm
85mm
THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
General
IMPORTANT SAFETY ADVICE
The Dimplex passive infra –red detector switch has been designed to
enable Dimplex Quartz and ceramic heaters (or any other heater up to
3kW) It automatically switches the heater on and off, depending on
whether the area below the heater is occupied.
•
The installation of this product should be carried out
by a competent person or electrician in strict
accordance of the current IEE Wiring Regulations
The DX4130 is designed to be used in conjunction
with Dimplex heaters up to 3kW electrical loading.
Only to be used on a 220-240Volt A.C. ~ electricity
supply
Electricity supply must be isolated before
commencement of installation
Always isolate the detector switch and the heater
from the electricity supply before undertaking any
maintenance work
•
•
•
•
Features
•
•
•
•
•
•
Time delay adjustment
Full 180º coverage over 15m if required
Size of detection area can be reduced
Approved to VDE 0632 and IEC 669-2-1
Separate wall-box and plug in detector lead to simplify installation
IP54 rated
•
Must not be installed and used in the vicinity of a
bathroom or swimming pool
Contents
X 1 Instruction sheet
X 1 grey wall box with fixed terminal block
X 1 PIR switch with pre-wired plug in connection
X 2 screws to affix PIR switch to wall box
X 3 screw caps
X 1 lens mask
Installation
(Please also refer to the IMPORTANT SAFETY ADVICE)
Before undertaking installation work, ensure the electricity supply is disconnected from any relevant fixed wiring.
Supply cable is not provided with this product, and it should therefore be installed by a competent person or electrician
This PIR detector must be used on an A.C. ~ supply only
Dimplex Quartz and ceramic heaters operate by emitting radiant heat within a specific area or zone.
The beam of radiant heat will interfere with the correct performance of the PIR detector unless the PIR detector is mounted outside the ‘throw’ of
radiant heat. It is therefore essential that the PIR detector is mounted as outlined below:
1. For installation of Quartz and ceramic heaters, please refer to the relevant installation instructions.
2. The PIR should be positioned to cover the desired sensing area without obstruction, avoiding the direct ‘throw’ of the heater.
3. The PIR should be wired directly back to a type C MCB or 13 amp re-wireable fuse. The cable should not exceed 2.5mm².
4. Remove screws and disconnect the plug connecting the detector to the key box. When removing the detector head, the latch on plug
should be released as indicated. (see Fig.1.)
Detector Head Plug
Press Down
Fig.1.
Download from Www.Somanuals.com. All Manuals Search And Download.
Testing
1. Set the light level
5
to maximum (clockwise), and the time on
to minimum (anti-clockwise).
2. Move in and out of detection pattern checking the PIR detector switches load on and then off. Once the detection area has been set
satisfactorily, adjust the time (blue knob) to the desired level. For your convenience optimum settings have been indicated.
3. If the unit does not operate, refer to the check list and fault finding list.
Check List
1. Check the supply to the detector
2. If the unit is being tested during daylight , ensure that the photocell has been adjusted in accordance with point 1 in the ‘Testing’
section.
3. Check detector is connected to the heater correctly
Fault Finding List
Problem
Solution
The unit will not switch on
•
•
•
•
Check power is supplied to the unit
Check the plug in connection from the detector head is inserted in to the wall box correctly
Check to see that the lamps are fitted correctly to the heater(s)
Check mounting height and adjust angle of the unit downwards to reduce range (note the unit is
designed to switch at a maximum of 15 metres with 170Ib (77kg) person walking at 90º to the
unit. Alternatively fit an appropriate mask.
Unit is detecting at too long a range
IMPORTANT: at 10ºC this unit may detect in excess of 20 metres.
Unit switches on for no apparent
reason
•
•
Check the unit is not sited near any vents or heating flues
Infra-red patterns are given off by electrical appliances
NOTE: to reduce sensitivity, blank off areas C1, C2, C3, C4 of the lens mask
Unit will not switch off
•
Are you standing by the detection zone? Whilst you are moving in and out of the detection area
the unit will continue to detect. The heater on time is from the last moment detection was made.
Technical Specification
Switching capability – Up to 3kW
Operating Power – 3kW
Detection Range – 15 metres maximum
Detection Angle - 180º
Heater on time – Adjustable to 10 seconds, 60 seconds, 3.5 minutes, 6 minutes, 9 minutes, 12 minutes, 13.5 minutes,
16 minutes, 21 minutes (approximately)
IMPORTANT: When unit is first connected to the mains the light will switch on – even in daylight.
Allow unit to reset before testing
After Sales Care
Your product is guaranteed for one year from the date of purchase.
Within this period, we undertake to repair or exchange this product free of charge (subject to availability) provided it has been
installed and operated in accordance with these instructions.
Your rights under this guarantee are additional to your statutory rights, which in turn are not affected by this guarantee.
Should you require after sales service you should contact the supplier through whom you purchased the product or contact our
customer service help desk on 0845 600 5111. It would assist us if you can quote the model number, series, date of purchase,
and nature of the fault at the time of your call. The customer service help desk will also be able to advise you should you need to
purchase any spares.
Please do not return a faulty product to us in the first instance as this may result in loss or damage and delay in providing you
with a satisfactory service.
Please retain your receipt as proof of purchase
UK customer helpline (8.00AM-6.00PM Mon-Fri; 8.30AM-1.00PM Sat)
Glen Dimplex UK Ltd
Millbrook House
Grange Drive
Hedge End
Southampton
SO30 2DF
Customer helpline
Tel. 0845 600 5111
Fax. 01489 773053
e-mail. [email protected]
Republic of Ireland
Tel. 01 842 4833
[C] Glen Dimplex UK Ltd.
All rights reserved. Material contained in this publication may not be reproduced in whole or part, without the prior permission in writing from
Glen Dimplex UK Limited.
Download from Www.Somanuals.com. All Manuals Search And Download.
|