VENT-FREE PROPANE/LP GAS HEATER
OWNER’S OPERATION AND INSTALLATION MANUAL
CGP10TA
and
CGP10TLA
WARNING: Improper installation,
WARNING: If the information in this manual is not
adjustment, alteration, service, or
followed exactly, a fire or explosion may result caus-
maintenance can cause injury or
ing property damage, personal injury, or loss of life.
property damage. Refer to this
— Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
manualforcorrectinstallationand
operational procedures. For as-
sistanceoradditionalinformation
consult a qualified installer, ser-
vice agency, or the gas supplier.
— WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use
any phone in your building.
WARNING: This is an unvented
gas-fired heater. It uses air (oxy-
gen) from the room in which it is
installed. Provisionsforadequate
combustion and ventilation air
must be provided. Refer to Air for
Combustion and Ventilation sec-
tion on page 4 in this manual.
• Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s in-
structions.
• Ifyoucannotreachyourgassupplier, callthefire
department.
— Installation and service must be performed by a quali-
fied installer, service agency, or the gas supplier.
This appliance may be installed in an aftermarket*, permanently located, manufactured
(mobile) home, where not prohibited by local codes.
This appliance is only for use with the type of gas indicated on the rating plate. This
appliance is not convertible for use with other gases.
*Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer
Save this manual for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
OWNER’S MANUAL
PRODUCT
IDENTIFICATION
PRODUCT
FEATURES
SAFETY DEVICE
Ignitor Button
Control Knob
This heater has a pilot with an Oxygen
DepletionSensing(ODS)safetyshutoffsys-
tem. The ODS/pilot is a required feature for
vent-freeroomheaters.TheODS/pilotshuts
off the heater if there is not enough fresh air.
PIEZO IGNITION SYSTEM
This heater has a piezo ignitor. This system
requires no matches, batteries, or other
sources to light heater.
Grill
Guard
THERMOSTATIC HEAT
CONTROL
Glass
Panel
This heater has a thermostat sensing bulb
and thermostat control. This results in the
greatest heater comfort. This can also result
in lower gas bills.
Heater
Cabinet
Front
Panel
Figure 1 - Vent-Free Propane/LP Gas Heater
LOCAL CODES
UNPACKING
Install and use heater with care. Follow all 1. Remove heater from carton.
localcodes.Intheabsenceoflocalcodes,use
2. Remove all protective packaging ap-
plied to heater for shipment.
the latest edition of The National Fuel Gas
CodeANSZ223.1,alsoknownasNFPA54*.
3. Check heater for any shipping damage.
If heater is damaged, promptly inform
dealer where you bought heater.
*Available from:
American National Standards Institute, Inc.
1430 Broadway
New York, NY 10018
National Fire Protection Association, Inc.
Batterymarch Park
Quincy, MA 02269
104268
3
Download from Www.Somanuals.com. All Manuals Search And Download.
VENT-FREE PROPANE/LP GAS HEATER
Confined and Unconfined
Spaces
PROVIDING ADEQUATE
VENTILATION
AIR FOR
COMBUSTION AND
VENTILATION
The National Fuel Gas Code ANS Z223.1
defines a confined space as a space whose
volume is less than 50 cubic feet per 1000
Btuperhour(4.8cubicmetersperkw)ofthe
aggregate input rating of all appliances in-
stalledinthatspaceandanunconfinedspace
as a space whose volume is not less than 50
cubic feet per 1000 Btu per hour (4.8 cubic
meters per kw) of the aggregate input rating
of all appliances installed in that space.
Rooms communicating directly with the
spaceinwhichtheappliancesareinstalled*,
through openings not furnished with doors,
are considered a part of the unconfined
space.
The following are excerpts from National
Fuel Gas Code. NFPA 54/ANS Z223.1, Sec-
tion5.3, AirforCombustionandVentilation.
WARNING: This heater shall
notbeinstalledinaconfinedspace
or unusually tight construction
unless provisions are provided
foradequatecombustionandven-
tilation air. Read the following in-
structions to insure proper fresh
air for this and other fuel-burning
appliances in your home.
All spaces in homes fall into one of the three
following ventilation classifications:
1. Unusually Tight Construction
2. Unconfined Space
3. Confined Space
The information on pages 4 through 6 will
help you classify your space and provide
adequate ventilation.
Unusually Tight Construction
Today’s homes are built more energy effi-
cient than ever. New materials, increased
insulation, and new construction methods
helpreduceheatlossinhomes. Homeowners
weather strip and caulk around windows and
doorstokeepthecoldairoutandthewarmair
in. During heating months, home owners
want their homes as airtight as possible.
The air that leaks around doors and win-
dows may provide enough fresh air for
combustion and ventilation. However, in
buildings of unusually tight construction,
you must provide additional fresh air.
This heater shall not be installed in a con-
fined space or unusually tight construction
unless provisions are provided for adequate
combustion and ventilation air.
*Adjoining rooms are communicating only
iftherearedoorlesspassagewaysorventila-
tion grills between them.
Unusually tight construction is de-
fined as construction where:
While it is good to make your home energy
efficient, your home needs to breathe. Fresh
air must enter your home. All fuel-burning
appliances need fresh air for proper com-
bustion and ventilation.
a. walls and ceilings exposed to the
outside atmosphere have a con-
tinuous water vapor retarder with
a rating of one perm (6 x 10-11 kg
per pa-sec-m2) or less with open-
ings gasketed or sealed and
Exhaust fans, fireplaces, clothes dryers, and
fuel burning appliances draw air from the
house to operate. You must provide ad-
equate fresh air for these appliances. This
will insure proper venting of vented fuel-
burning appliances.
b. weather stripping has been
added on openable windows and
doors and
c. caulking or sealants are applied
to areas such as joints around
window and door frames, be-
tween sole plates and floors, be-
tween wall-ceiling joints, be-
tween wall panels, at penetra-
tions for plumbing, electrical, and
gas lines, and at other openings.
If your home meets all of the three
criteria above, you must provide ad-
ditional fresh air. See Ventilation Air
From Outdoors, page 6.
If your home does not meet all of the
three criteria above, proceed to Deter-
mining Fresh-Air Flow for Heater Lo-
cation on page 5.
104268
4
Download from Www.Somanuals.com. All Manuals Search And Download.
OWNER’S MANUAL
AIR FOR
COMBUSTION AND
VENTILATION
Continued
DETERMINING FRESH-AIR FLOW FOR HEATER LOCATION
Determining if You Have a Confined or Unconfined Space
Use this worksheet to determine if you have a confined or unconfined space.
Space:Includestheroominwhichyouwillinstallheaterplusanyadjoiningroomswithdoorlesspassagewaysorventilationgrillsbetween
the rooms.
1. Determine the volume of the space (length x width x height).
Length x Width x Height = ________________ cu. ft. (volume of space)
Example: Space size 18 ft. (length) x 16 ft. (width) x 8 ft. (ceiling height) = 2304 cu. ft. (volume of space)
If additional ventilation to adjoining room is supplied with grills or openings, add the volume of these rooms to the total volume of
the space.
2. Divide the space volume by 50 cubic feet to determine the maximum Btu/Hr the space can support.
_______________ (volume of space) ÷ 50 cu. ft. = (Maximum Btu/Hr the space can support)
Example: 2304 cu. ft. (volume of space) ÷ 50 cu. ft. = 46.1 or 46,100 (maximum Btu/Hr the space can support)
3. Add the Btu/Hr of all fuel burning appliances in the space.
Vent-free heater
Gas water heater*
Gas furnace
_________________ Btu/Hr
_________________ Btu/Hr
_________________ Btu/Hr
_________________ Btu/Hr
_________________ Btu/Hr
Example:
Gas water heater
Vent-free heater
Total
40,000 Btu/Hr
10,000 Btu/Hr
50,000 Btu/Hr
Vented gas heater
Gas fireplace logs
+
=
Other gas appliances* + _________________ Btu/Hr
Total = _________________ Btu/Hr
* Do not include direct-vent gas appliances. Direct-vent draws combustion air from the outdoors and vents to the outdoors.
4. Compare the maximum Btu/Hr the space can support with the actual amount of Btu/Hr used.
_________________ Btu/Hr (maximum the space can support)
_________________ Btu/Hr (actual amount of Btu/Hr used)
Example: 46,100 Btu/Hr (maximum the space can support)
50,000 Btu/Hr (actual amount of Btu/Hr used)
The space in the above example is a confined space because the actual Btu/Hr used is more than the maximum Btu/Hr the space can support.
You must provide additional fresh air. Your options are as follows:
A. Rework worksheet, adding the space of an adjoining room. If the extra space provides an unconfined space, remove door to adjoin-
ing room or add ventilation grills between rooms. See Ventilation Air From Inside Building, page 6.
B. Vent room directly to the outdoors. See Ventilation Air From Outdoors, page 6.
C. Install a lower Btu/Hr heater, if lower Btu/Hr size makes room unconfined.
If the actual Btu/Hr used is less than the maximum Btu/Hr the space can support, the space is an unconfined space. You will need no
additional fresh air ventilation.
WARNING: If the area in which the heater may be operated is smaller than that defined as an unconfined space
or if the building is of unusually tight construction, provide adequate combustion and ventilation air by one of
the methods described in the National Fuel Gas Code, ANS Z223.1, Section 5.3 or applicable local codes.
Continued
104268
5
Download from Www.Somanuals.com. All Manuals Search And Download.
VENT-FREE PROPANE/LP GAS HEATER
AIR FOR
COMBUSTION AND
12"
VENTILATION
Continued
Ventilation Grills
Into Adjoining Room,
VENTILATION AIR
Ventilation
Grills
into Adjoining
Room,
Option 2
Ventilation Air From Inside
Building
Or
Remove
Door into
Adjoining
Room,
Option 1
Thisfreshairwouldcomefromanadjoining
unconfined space. When ventilating to an
adjoining unconfined space, you must pro-
vide two permanent openings: one within
12" of the ceiling and one within 12" of the
floor on the wall connecting the two spaces
(see options 1 and 2, Figure 2). You can also
remove door into adjoining room (see op-
tion 3, Figure 2). Follow the National Fuel
Gas Code NFPA 54/ANS Z223.1, Section
5.3, Air for Combustion and Ventilation for
required size of ventilation grills or ducts.
Option 3
12"
WARNING: Rework work-
sheet, adding the space of the
adjoining unconfined space. The
combined spaces must have
enough fresh air to supply all
appliances in both spaces.
Figure 2 - Ventilation Air from Inside Building
Ventilated
Attic
Outlet
Air
Ventilation Air From Outdoors
Provide extra fresh air by using ventilation
grills or ducts. You must provide two per-
manent openings: one within 12" of the
ceiling and one within 12" of the floor.
Connect these items directly to the outdoors
orspacesopentotheoutdoors.Thesespaces
include attics and crawl spaces. Follow the
National Fuel Gas Code NFPA 54/ANS
Z223.1,Section5.3,AirforCombustionand
Ventilation for required size of ventilation
grills or ducts.
Outlet
Air
To Attic
To
Crawl
Space
Inlet
Air
Ventilated
Crawl Space
Inlet Air
IMPORTANT: Do not provide openings
for inlet or outlet air into attic if attic has a
thermostat-controlled power vent. Heated
air entering the attic will activate the power
vent.
Figure 3 - Ventilation Air from Outdoors
104268
6
Download from Www.Somanuals.com. All Manuals Search And Download.
OWNER’S MANUAL
CEILING
LOCATING HEATER
INSTALLATION
This heater is designed to be mounted on a
wall.
NOTICE: This heater is intended
foruseassupplementalheat.Use
this heater along with your pri-
mary heating system. Do not in-
stall this heater as your primary
heat source. If you have a central
heating system, you may run
system’scirculatingblowerwhile
using heater. This will help circu-
late the heat throughout the
house. In the event of a power
outage, you can use this heater
as your primary heat source.
36"
Minimum
6"
WARNING:Maintainthemini-
mumclearancesshowninFigure
4.Ifyoucan,providegreaterclear-
ances from floor, ceiling, and
joining wall.
Minimum
From
Sides Of
Heater
Right
Side
Left
Side
Minimum to
Top Surface
WARNING: Never install the
heater
• in a bathroom
of Carpeting,
3"
e
Tile or Other
• in a recreational vehicle
• where curtains, furniture,
clothing, or other flammable
objectsarelessthan36inches
from the front, top, or sides of
the heater
• as a fireplace insert
• in high traffic areas
• in windy or drafty areas
Combustible
FLOOR
Material
Figure4-MountingClearancesAsViewed
From Front of Heater
WARNING: A qualified ser-
vice person must install heater.
Follow all local codes.
THERMOSTAT SENSING
BULB
CHECK GAS TYPE
The thermostat sensing bulb is located in-
side the heater. Do not move this bulb dur-
ing installation or operation of the heater.
Useonlypropane/LPgas.Ifyourgassupply
is not propane/LP, do not install heater. Call
dealer where you bought heater for proper
type heater.
CAUTION: This heater cre-
ates warm air currents. These
currents move heat to wall sur-
faces next to heater. Installing
heater next to vinyl or cloth wall
coverings or operating heater
where impurities (such as to-
bacco smoke, aromatic candles,
cleaning fluids, oil or kerosene
lamps, etc.) in the air exist, may
discolor walls.
INSTALLING HEATER TO
WALL
INSTALLATION ITEMS
Beforeinstallingheater,makesureyouhave
the items listed below.
Marking Screw Locations
1. Determine where you will locate heater.
• external regulator (supplied by installer)
• piping (check local codes)
• sealant (resistant to propane/LP gas)
• equipment shutoff valve *
• ground joint union
• test gauge connection *
• sediment trap
• tee joint
WARNING:Maintainminimum
clearances shown in Figure 5. If
you can, provide greater clear-
ancesfromfloorandjoiningwall.
IMPORTANT:Vent-freeheatersaddmois-
ture to the air. Although this is beneficial,
installing heater in rooms without enough
ventilation air may cause mildew to form
from too much moisture. See Air for Com-
bustion and Ventilation, pages 4 through 6.
2. Mark two mounting screw locations on
wall (see Figure 5).
• pipe wrench
8 7/8"
Minimum
To
Maintain 6"
Clearance
From Wall
7 3/4"
* A CSA/AGA design-certified equipment
shutoff valve with 1/8" NPT tap is an ac-
ceptable alternative to test gauge connec-
tion. The optional CSA/AGA design-certi-
fied equipment shutoff valve can be pur-
chased from your dealer. See Accessory,
page 13.
CAUTION: If you install the
heater in a home garage
• heater pilot and burner must
be at least 18 inches above
floor
20 1/4"
Mounting
Screw
Locations
Minimum To
Maintain 3"
Clearance
From Floor
• locateheaterwheremovingve-
hicle will not hit it
Forconvenienceandefficiency,installheater
FLOOR
Figure 5 - Mounting Screw Locations
• where there is easy access for operation,
inspection, and service
• in coldest part of room
Continued
104268
7
Download from Www.Somanuals.com. All Manuals Search And Download.
VENT-FREE PROPANE/LP GAS HEATER
Installing Bottom Mounting
Screw
1. Locate bottom mounting hole. This
hole is near bottom on back panel of
heater (see Figure 11).
Thin or Thick
Wall
(thick wall
shown)
INSTALLATION
Continued
Installing Two Mounting Screws
1/16"
Space
Note: Wall anchors and mounting screws
areinhardwarepackage.Thehardwarepack-
age is provided with heater.
2. Mark screw location on wall.
3. Remove heater from wall.
Solid Wall
Attaching To Wall Stud Method
4. If installing bottom mounting screw
into hollow or solid wall, install wall
anchor. Follow steps 1 through 5 un-
der Attaching To Wall Anchor Method,
column 1.
Figure 8 - Tightening Anchors
For attaching mounting screw to wall stud
1. Drill hole at marked location using 9/64"
drill bit.
Placing Heater On Mounting
Screws
1. Locate two keyhole slots on back panel
of heater (see Figure 9).
2. Insert mounting screw into wall stud.
If installing bottom mounting screw
into wall stud, drill hole at marked lo-
cation using 9/64" drill bit.
3. Tighten screw until 1/16" space (thick-
ness of penny) is between screwhead
and wall.
5. Replace heater on wall.
2. Place large openings of slots over
screwheads. Slide heater down until
screws are in small portion of slots.
Attaching To Wall Anchor Method
6. Insert bottom anchor screw through
back panel into bottom anchor or
drilled hole (see Figure 11).
Follow instructions below to attach mount-
ing screws to hollow walls (wall areas be-
tween studs) or solid walls (concrete or
masonry).
7. Tighten screw until heater is firmly
secured to wall. Do not over tighten.
1. Drill holes at marked locations using
5/16" drill bit. For solid walls (concrete
or masonry), drill at least 1 1/4" deep.
Note: Do not replace front panel at this
time. Replace front panel after making
gas connections and checking for leaks
(see pages 9 and 10 ).
Keyhole Slots
2. Fold wall anchor (see Figure 6).
3. Insert wall anchor (wings first) into
hole. Tap anchor flush to wall.
Figure 9 - Location Of Keyhole Slots On
Back Panel Of Heater
4. For thin walls (1/2" or less), insert red
key into wall anchor. Push red key to
“pop” open anchor wings (see Figure
7). IMPORTANT:Do not hammer key!
Removing Front Panel Of Heater
1. Remove two screws near bottom cor-
ners of front panel.
For thick walls (over 1/2" thick) or solid
walls, do not pop open wings.
2. Lift straight up on grill guard until it stops.
Grill guard will slide up about 1/4".
5. Tighten two screws until 1/16" space
(thickness of penny) is between
screwheads and wall (see Figure 8).
3. Pull bottom of front panel forward, then
down.
Figure 11 - Installing Bottom Mounting
Screw
Figure 6 - Folding Anchor
Thin Walls
(1/4" to 1/2"
thick)
Figure 7 - Popping Open Anchor Wings
For Thin Walls
Figure 10 - Removing Front Panel Of
Heater
104268
8
Download from Www.Somanuals.com. All Manuals Search And Download.
OWNER’S MANUAL
Installationmustincludeanequipmentshutoff Apply pipe joint sealant lightly to male
valve, ground joint union, and plugged 1/8" threads. This will prevent excess sealant
NPTtap.LocateNPTtapwithinreachfortest from going into pipe. Excess sealant in pipe
gauge hook up. NPT tap must be upstream could result in clogged heater valves.
from heater (see Figure 13).
INSTALLATION
Continued
CONNECTING TO GAS
SUPPLY
CAUTION:Usepipejointseal-
ant that is resistant to liquid pe-
troleum (LP) gas.
IMPORTANT:Installanequipmentshutoff
valve in an accessible location. The equip-
ment shutoff valve is for turning on or
shutting off the gas to the appliance.
WARNING:Thisappliancere-
quires a 3/8" NPT (National Pipe
Thread) inlet connection to the
pressure regulator.
Installsedimenttrapinsupplylineasshown
in Figure 13. Locate sediment trap where it
is within reach for cleaning. Locate sedi-
ment trap where trapped matter is not likely
to freeze. A sediment trap traps moisture
and contaminants. This keeps them from
going into heater controls. If sediment trap
is not installed or is installed wrong, heater
may not run properly.
Propane/LP
Supply
Tank
WARNING: A qualified service
personmustconnectheatertogas
supply. Follow all local codes.
External
Regulator
Vent
Pointing
Down
IMPORTANT: Hold pressure regulator
with wrench when connecting it to gas pip-
ing and/or fittings.
CAUTION: Never connect
heater directly to the propane/LP
supply. This heater requires an
externalregulator(notsupplied).
Install the external regulator be-
tweentheheaterandpropane/LP
supply.
Figure 12 - External Regulator With Vent
Pointing Down
The installer must supply an external regu-
lator. The external regulator will reduce
incoming gas pressure. You must reduce
incoming gas pressure between 11 and 14
inches of water. If you do not reduce incom-
ing gas pressure, heater regulator damage
could occur. Install external regulator with
the vent pointing down as shown in Figure
12. Pointing the vent down protects it from
freezing rain or sleet.
Pressure
Regulator
3/8" NPT
Pipe Nipple
Heater
Cabinet
Ground Joint Union
Tee Joint
Equipment Shutoff
Valve *
Reducer
Test
CAUTION: Use only new,
black iron or steel pipe. Inter-
nally-tinned copper tubing may
be used in certain areas. Check
your local codes. Use pipe 3/8"
diameter or greater to allow
proper gas volume to heater. If
pipe is too small, undue loss of
pressure will occur.
Bushing to
Gauge
Connection *
1/8" NPT
From External
Regulator
(11" W.C. to
14" W.C.
1/8" NPT
Plug Tap
Tee
Joint
Pressure)
3" Minimum
Pipe
Nipple
Sediment Trap
Cap
Figure 13 - Gas Connection
* ACSA/AGAdesign-certifiedequipmentshutoffvalvewith1/8"NPTtapisanacceptable
alternative to test gauge connection. Purchase the optional CSA/AGA design-certified
equipment shutoff valve from your dealer. See Accessory, page 13.
Continued
104268
9
Download from Www.Somanuals.com. All Manuals Search And Download.
VENT-FREE PROPANE/LP GAS HEATER
Test Pressures Equal To or Less Than 1/2
PSIG (3.5 kPa)
Pressure Testing Heater Gas
Connections
1. Open equipment shutoff valve (see Fig-
ure 14).
INSTALLATION
Continued
1. Close equipment shutoff valve (see Fig-
ure 14).
CHECKING GAS
CONNECTIONS
2. Pressurize supply piping system by ei-
ther using compressed air or opening
propane/LP supply tank valve.
2. Open propane/LP supply tank valve.
3. Make sure control knob of heater is in
the OFF position.
WARNING: Test all gas pip-
ing and connections for leaks
after installation or servicing.
Correct all leaks at once.
3. Check all joints from propane/LP sup-
ply tank to equipment shutoff valve (see
Figure 15). Apply mixture of liquid
soap and water to gas joints. Bubbles
forming show a leak.
4. Check all joints from equipment shutoff
valve to control valve (see Figure 15).
Apply mixture of liquid soap and wa-
ter to gas joints. Bubbles forming show
a leak.
WARNING: Never use an open
flame to check for a leak. Apply a
mixtureofliquidsoapandwaterto
all joints. Bubbles forming show a
leak. Correct all leaks at once.
4. Correct all leaks at once.
5. Correct all leaks at once.
6. Light heater (see Operating Heater,
pages 11 and 12). Check the rest of the
internal joints for leaks.
Open
Equipment
Shutoff
Valve
7. Turn off heater (see To Turn Off Gas to
Appliance, page 12).
CAUTION: Make sure exter-
nal regulator has been installed
between propane/LP supply and
heater.SeeguidelinesunderCon-
necting to Gas Supply, page 9.
8. Replace front panel.
Closed
Figure 14 - Equipment Shutoff Valve
Pressure Testing Gas Supply
Piping System
Test Pressures In Excess Of 1/2 PSIG
(3.5 kPa)
Control
Valve
Location
1. Disconnect appliance with its appliance
main gas valve (control valve) and equip-
ment shutoff valve from gas supply pip-
ing system. Pressures in excess of 1/2 psig
will damage heater regulator.
Propane/LP
Supply Tank
2. Cap off open end of gas pipe where
equipment shutoff valve was connected.
3. Pressurize supply piping system by ei-
ther using compressed air or opening
propane/LP supply tank valve.
Equipment
Shutoff
Valve
4. Check all joints of gas supply piping
system. Apply mixture of liquid soap
and water to gas joints. Bubbles form-
ing show a leak.
5. Correct all leaks at once.
Figure 15 - Checking Gas Joints
6. Reconnect heater and equipment
shutoff valve to gas supply. Check re-
connected fittings for leaks.
104268
10
Download from Www.Somanuals.com. All Manuals Search And Download.
OWNER’S MANUAL
8. Turn control knob counterclockwise
LIGHTING
OPERATING
HEATER
C-clockwise
to desired heating level. The
INSTRUCTIONS
main burner should light. Set control
1. STOP! Read the safety information,
column 1.
knob to any heat level between HI
and LO.
FOR YOUR SAFETY
READ BEFORE
LIGHTING
2. Make sure equipment shutoff valve
is fully open.
CAUTION:Donottrytoadjust
heatinglevelsbyusingtheequip-
ment shutoff valve.
3. Turn control knob clockwise
Clockwise
to the OFF position (see Figure 16).
WARNING: If you do not fol-
low these instructions exactly, a
fireorexplosionmayresultcaus-
ing property damage, personal
injury or loss of life.
4. Wait five (5) minutes to clear out any
gas. Then smell for gas, including
near the floor. If you smell gas,
STOP! Follow “B” in the safety in-
formation. If you don’t smell gas, go
to the next step.
Ignitor Button
Control Knob
LO
P I L O T
O F F
A. This appliance has a pilot which must
H I
be lighted by hand. When lighting the 5. Turn control knob counterclockwise
pilot, follow these instructions exactly.
to the PILOT position.
C-clockwise
IGNITOR
B. BEFORE LIGHTING smell all
around the appliance area for gas. Be
sure to smell next to the floor because
some gas is heavier than air and will
settle on the floor.
Press in control knob for five (5) sec-
onds (see Figure 16).
Figure 16 - Control Knob In The OFF
Position
Note: You may be running this
heater for the first time after hook-
ing up to gas supply. If so, the con-
trol knob may need to be pressed in
for 30 seconds. This will allow air to
bleed from the gas system.
Ignitor Electrode
WHAT TO DO IF YOU SMELL
GAS
• Do not try to light any appliance.
Pilot Burner
Thermocouple
•
Do not touch any electric switch; do
not use any phone in your building.
6. With control knob pressed in, push
down and release ignitor button. This
will light pilot. The pilot is attached
to the front of burner. The pilot can
be seen through the glass panel. If
needed, keep pressing ignitor button
until pilot lights.
• Immediately call your gas supplier
from a neighbor’s phone. Follow
the gas supplier’s instructions.
• If you cannot reach your gas sup-
plier, call the fire department.
Figure 17 - Pilot
C. Use only your hand to push in or turn
the gas control knob. Never use tools.
If the knob will not push in or turn
by hand, don’t try to repair it, call a
qualified service technician or gas
supplier. Force or attempted repair
may result in a fire or explosion.
Note: If pilot does not stay lit, refer
to Troubleshooting, pages 14 through
16. Also contact a qualified service
person or gas supplier for repairs.
Until repairs are made, light pilot with
match. To light pilot with match, see
Manual Lighting Procedure, page 12.
D. Do not use this appliance if any part
has been under water. Immediately
call a qualified service technician to
inspect the appliance and to replace
any part of the control system and
any gas control which has been un-
der water.
7. Keep control knob pressed in for 30
seconds after lighting pilot. After 30
seconds, release control knob.
•
If control knob does not pop up when
released, contact a qualified service
person or gas supplier for repairs.
Note: If pilot goes out, repeat steps
3 through 7. This heater has a safety
interlock system. Wait one (1) minute
before lighting pilot again.
Continued
104268
11
Download from Www.Somanuals.com. All Manuals Search And Download.
VENT-FREE PROPANE/LP GAS HEATER
MANUAL LIGHTING
PROCEDURE
BURNER FLAME PATTERN
OPERATING
Figure 20 shows a correct burner flame
pattern.Figure21showsanincorrectburner
flame pattern. The incorrect burner flame
patternshowsyellowtippingoftheflame. It
also shows the flame higher than 1/2 the
glass panel height.
HEATER
1. Remove front panel (see Figure 10,
page 8).
Continued
2. Follow steps 1 through 5 under Light-
ing Instructions, page 11.
TO TURN OFF GAS
TO APPLIANCE
3. With control knob pressed in, strike
match. Hold match to pilot until pi-
lot lights.
Shutting Off Heater
1. Turn control knob clockwise
to the OFF position.
WARNING: If yellow tipping
occurs, your heater could pro-
duce increased levels of carbon
monoxide. If burner flame pat-
tern shows yellow tipping, follow
the instructions below.
Clockwise
4. Keep control knob pressed in for 30
seconds after lighting pilot. After 30
seconds, release control knob. Follow
step 8 under Lighting Instructions,
page 11.
2. Turn off all electric power to the ap-
pliance if service is to be performed.
Shutting Off Burner Only (pilot
stays lit)
5. Replace front panel.
NOTICE: Do not mistake orange
flames with yellow tipping. Dust
or other fine particles enter the
heater and burn causing brief
patches of orange flame.
Turn control knob clockwise
the PILOT position.
to
Clockwise
INSPECTING
BURNER
THERMOSTAT
CONTROL
OPERATION
Check pilot flame pattern and burner flame
pattern often.
Ifburnerflamepatternisincorrect,asshown
in Figure 21
PILOT FLAME PATTERN
The thermostatic control used on these
models differs from standard thermo-
stats. Standard thermostats simply turn
on and off the burner. The thermostat
used on this heater senses the room tem-
perature. The thermostat adjusts the
amount of gas flow to the burner. This
increases or decreases the burner flame
height. At times the room may exceed the
set temperature. If so, the burner will
shut off. The burner will cycle back on
when room temperature drops below the
set temperature. The control knob can be
set to any heat level between HI and LO.
• turn heater off (see To Turn Off Gas to
Appliance, column 1)
Figure18showsacorrectpilotflamepattern.
Figure 19 shows an incorrect pilot flame
pattern.Theincorrectpilotflameisnottouch-
ing the thermocouple. This will cause the
thermocouple to cool. When the thermo-
couple cools, the heater will shut down.
•
see Troubleshooting, pages 14 through 16
If pilot flame pattern is incorrect, as shown
in Figure 19
1/2 GLASS HEIGHT
• turn heater off (see To Turn Off Gas to
Appliance, column 1)
Figure 20 - Correct Burner Flame Pattern
•
see Troubleshooting, pages 14 through 16
Note: The thermostat sensing bulb mea-
sures the temperature of air near the
heatercabinet.Thismaynotalwaysagree
with room temperature (depending on
housing construction, installation loca-
tion, room size, open air temperatures,
etc.). Frequent use of your heater will let
you determine your own comfort levels.
Yellow
Tipping
Pilot Burner
Thermocouple
1/2 GLASS HEIGHT
GRH/OV 007
FigureG1O8OD-PILCOTo/LrPrect Pilot Flame Pattern
Figure21-IncorrectBurnerFlamePattern
Pilot Burner
Thermocouple
BAD PILOT/LP
GRH/OV 008
Figure 19 - Incorrect Pilot Flame Pattern
104268
12
Download from Www.Somanuals.com. All Manuals Search And Download.
OWNER’S MANUAL
Pilot Air Inlet Hole
CLEANING AND
MAINTENANCE
SERVICE
HINTS
When Gas Pressure Is Too Low
•
pilot will not stay lit
WARNING: Turn off heater
and let cool before cleaning.
Pilot Assembly
Figure 22 - Pilot Inlet Air Hole
• burner will have delayed ignition
• heater will not produce specified heat
• propane/LP gas supply may be low
CAUTION: You must keep
control areas, burner, and circu-
lating air passageways of heater
clean. Inspect these areas of
heater before each use. Have
heaterinspectedyearlybyaquali-
fied service person. Heater may
needmorefrequentcleaningdue
to excessive lint from carpeting,
bedding material, pet hair, etc.
CABINET
When Gas Quality Is Bad
• pilot will not stay lit
Air Passageways
• Use a vacuum cleaner or pressurized air
to clean.
• burner will produce flames and soot
• heater will backfire when lit
Youmayfeelyourgaspressureistoolowor
gas quality is bad. If so, contact your local
propane/LP gas supplier.
Exterior
• Use a soft cloth dampened with a mild
soap and water mixture. Wipe the cabinet
to remove dust.
ACCESSORY
ODS/PILOT AND BURNER
ORIFICE
• Use a vacuum cleaner, pressurized air,
or small, soft bristled brush to clean.
Purchasetheseheateraccessoriesfromyour
local dealer. If they cannot supply this ac-
cessories, either contact your nearest Parts
Central or call DESA International’s Parts
Department at 1-800-972-7879 for referral
information. You can also write to the ad-
dress listed on the back page of this manual.
SERVICE
PUBLICATIONS
Youcanpurchaseaservicemanualfromthe
address listed on the back page of this
manual. Send a check for $5.00 payable to
DESA International.
CLEANING BURNER
PILOT AIR INLET HOLE
We recommend that you clean the unit every
2,500hoursofoperationoreverythreemonths.
TECHNICAL
SERVICE
Wealsorecommendthatyoukeeptheburner
tubeandpilotassemblycleanandfreeofdust
and dirt. To clean these parts we recommend
using compressed air no greater than 30 PSI.
Yourlocalcomputerstore,hardwarestore,or
home center may carry compressed air in a
can. You can use a vacuum cleaner in the
blow position. If using compressed air in a
can, please follow the directions on the can.
If you don't follow directions on the can, you
could damage the pilot assembly.
You may have further questions about in-
stallation, operation, or troubleshooting. If
so, contact DESA International’s Technical
Service Department at 1-800-323-5190.
EQUIPMENT SHUTOFF
VALVE - GA5010
You can also visit DESA International’s
technical service web site at
Equipmentshutoffvalvewith1/8"NPTtap.
SPECIFICATIONS
1. Shut off the unit, including the pilot.
Allow the unit to cool for at least thirty
minutes.
CGP10TA/CGP10TLA
5,000/10,000
Propane/LP Only
Piezo
Btu (Variable)
Type Gas
Ignition
Pressure Regulator Setting
Inlet Gas Pressure (inches of water)
Maximum
2. Inspect burner, pilot for dust and dirt.
3. Blow air through the ports/slots and
holes in the burner.
8" W.C.
Clean the pilot assembly also. A yellow tip
on the pilot flame indicates dust and dirt in
the pilot assembly. There is a small pilot air
inlet hole about two inches from where the
pilot flame comes out of the pilot assembly
(see Figure 22). With the unit off, lightly
blow air through the air inlet hole. You may
blowthroughadrinkingstrawifcompressed
air is not available.
14"
11"
Minimum
Dimensions, Inches (H x W x D)
Heater (Including knobs and grill)
Carton
Weight (pounds)
Shipping
21 1/2 x 131/2 x 7
25 1/4 x 16 3/4 x 7 1/2
19
104268
13
Download from Www.Somanuals.com. All Manuals Search And Download.
VENT-FREE PROPANE/LP GAS HEATER
TROUBLESHOOTING
Note: For additional help, visit DESA
International’stechnicalservicewebsite
WARNING: Turn off heater
and let cool before servicing.
Only a qualified service per-
son should service and repair
heater.
CAUTION: Never use a wire,
needle, or similar object to clean
ODS/pilot.ThiscandamageODS/
pilot unit.
Note:Alltroubleshootingitemsarelistedin
order of operation.
OBSERVED PROBLEM
POSSIBLE CAUSE
REMEDY
When ignitor button is pressed, there is no 1. Ignitor cable pinched or wet
spark at ODS/pilot
1. Free ignitor cable if pinched by any
metal or tubing. Keep ignitor cable dry
2. Ignitor electrode not connected to igni- 2. Reconnect ignitor cable
tor cable
3. Piezo ignitor nut is loose
3. Tighten nut holding piezo ignitor to
heater cabinet. Nut is located inside
heater cabinet at top
4. Broken ignitor cable
4. Replace ignitor cable
5. Ignitor electrode broken
6. Bad piezo ignitor
7. Ignitor electrode positioned wrong
5. Replace ignitor
6. Replace piezo ignitor
7. Replace ignitor
When ignitor button is pressed, there is 1. Gas supply turned off or equipment 1. Turn on gas supply or open equipment
spark at ODS/pilot but no ignition
shutoff valve closed
shutoff valve
2. Control knob not in PILOT position
2. Turn control knob to PILOT position
3. Control knob not pressed in while in 3. Press in control knob while in PILOT
PILOT position
position
4. Air in gas lines when installed
4. Continue holding down control knob
Repeat igniting operation until air is re-
moved
5. ODS/pilot is clogged
5. Clean ODS/pilot (see Cleaning and
Maintenance, page 13) or replace ODS/
pilot assembly
6. Gas regulator setting is not correct
6. Replace gas regulator
ODS/pilot lights but flame goes out when 1. Control knob not fully pressed in
1. Press in control knob fully
control knob is released
2. Control knob not pressed in long enough 2. After ODS/pilot lights, keep control
knob pressed in 30 seconds
3. Safety interlock system has been triggered 3. Wait one minute for safety interlock sys-
tem to reset. Repeat ignition operation.
4. Equipment shutoff valve not fully open 4. Fully open equipment shutoff valve
5. Thermocouple connection loose at con- 5. Hand tighten until snug, then tighten 1/4
trol valve
turn more
6. Pilot flame not touching thermocouple, 6. A) Contact local propane/LP gas company
which allows thermocouple to cool,
causing pilot flame to go out. This prob-
lem could be caused by one or both of
the following:
A) Low gas pressure
B) Clean ODS/pilot (see Cleaning and
Maintenance, page 13) or replace ODS/
pilot assembly
B) Dirty or partially clogged ODS/pilot
7. Thermocouple damaged
8. Control valve damaged
7. Replace thermocouple
8. Replace control valve
104268
14
Download from Www.Somanuals.com. All Manuals Search And Download.
OWNER’S MANUAL
TROUBLESHOOTING
Continued
OBSERVED PROBLEM
POSSIBLE CAUSE
REMEDY
Burner does not light after ODS/pilot is lit
1. Burner orifice is clogged
1. Clean burner orifice (see Cleaning and
Maintenance, page 13) or replace burner
orifice
2. Burner orifice diameter is too small
3. Inlet gas pressure is too low
2. Replace burner orifice
3. Contact local propane/LP gas company
Delayed ignition of burner
1. Manifold pressure is too low
2. Burner orifice is clogged
1. Contact local propane/LP gas company
2. Clean burner orifice (see Cleaning and
Maintenance, page 13) or replace burner
orifice
Burner backfiring during combustion
1. Burner orifice is clogged or damaged
1. Clean burner orifice (see Cleaning and
Maintenance, page 13) or replace burner
orifice
2. Inlet gas pressure is too low
3. Burner damaged
2. Contact local propane/LP gas company
3. Replace burner
4. Gas regulator defective
4. Replace gas regulator
Yellow flame during burner combustion
1. Not enough air
1. Check burner for dirt and debris. If
found, clean burner (see Cleaning and
Maintenance, page 13)
2. Inlet gas pressure is too low
3. Gas regulator defective
2. Contact local propane/LP gas company
3. Replace gas regulator
Slightsmokeorodorduringinitialoperation 1. Residues from manufacturing processes 1. Problem will stop after a few hours of
operation
Heater produces a whistling noise when 1. Turn control knob to HI position when 1. Turn control knob to LO position and
burner is lit
burner is cold
let warm up for a minute
2. Air in gas line
2. Operate burner until air is removed from
line. Have gas checked by local propane/
LP gas company
3. Air passageways on heater blocked
3. Observe minimum installation clear-
ances (see Figure 4, page 7)
4. Dirty or partially clogged burner orifice 4. Clean burner (see Cleaning and Mainte-
nance, page 13) or replace burner orifice
Whitepowderresidueformingwithinburner 1. When heated, vapors from furniture pol- 1. Turn heater off when using furniture
box or on adjacent walls or furniture
ish, wax, carpet cleaners, etc. turn into
white powder residue
polish, wax, carpet cleaners, or similar
products
Continued
104268
15
Download from Www.Somanuals.com. All Manuals Search And Download.
VENT-FREE PROPANE/LP GAS HEATER
TROUBLESHOOTING
Continued
WARNING: If you smell gas
• Shut off gas supply.
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your
building.
• Immediately call your gas supplier from a neighbor’s phone.
Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire department.
IMPORTANT: Operating heater where impurities in air exist may create odors.
Cleaning supplies, paint, paint remover, cigarette smoke, cements and glues, new
carpet or textiles, etc., create fumes. These fumes may mix with combustion air and
create odors.
POSSIBLE CAUSE
REMEDY
OBSERVED PROBLEM
1. Metal expanding while heating or con- 1. This is common with most heaters. If
Heater produces a clicking/ticking noise
just after burner is lit or shut off
tracting while cooling
noise is excessive, contact qualified ser-
vice person
1. Heater burning vapors from paint, hair 1. Ventilate room. Stop using odor-causing
Heater produces unwanted odors
spray, glues, etc. See IMPORTANT
statement above
products while heater is running
2. Low fuel supply
2. Refill supply tank
3. Gas leak. SeeWarning statement at 3. Locate and correct all leaks (see Check-
top of page
ing Gas Connections, page 10)
1. Not enough fresh air is available
2. Low line pressure
3. ODS/pilot is partially clogged
1. Open window and/or door for ventilation
2. Contact local propane/LP gas company
3. Clean ODS/pilot (see Cleaning and
Maintenance, page 13)
Heater shuts off in use (ODS operates)
1. Gas leak. SeeWarning statement at 1. Locate and correct all leaks (see Check-
Gas odor even when control knob is in OFF
position
top of page
ing Gas Connections, page 10)
2. Control valve defective
2. Replace control valve
1. Foreign matter between control valve 1. Take apart gas tubing and remove for-
and burner eign matter
2. Gas leak. SeeWarning statement at 2. Locate and correct all leaks (see Check-
Gas odor during combustion
top of page
ing Gas Connections, page 10)
1. Not enough combustion/ventilation air
1. Refer to Air for Combustion and Venti-
lation requirements (page 4)
Moisture/condensationnoticedonwindows
104268
16
Download from Www.Somanuals.com. All Manuals Search And Download.
OWNER’S MANUAL
East Coast Energy Products
707 Broadway
W. Long Branch, NJ 07764-1542
732-870-8809
1-800-755-8809
PARTS CENTRAL
REPLACEMENT
PARTS
These Parts Centrals are privately-owned
businesses. Theyhaveagreedtosupportour
customer’s needs by providing original re-
placement parts and accessories.
Note: Use only original replacement parts.
Thiswillprotectyourwarrantycoveragefor
parts replaced under warranty.
Baltimore Electric
1348 Dixwell Avenue
Hamden, CT 06514-0322
1-800-397-7553
203-248-7553
Parts Department
PARTS UNDER WARRANTY
Tarantin Tank Co.
P.O. Box 6129
Freehold, NJ 07728-6129
908-780-9340
1-800-922-0724
Contact authorized dealer from whom you
purchased this product. If they cannot supply
original replacement part(s), call DESA
International’sTechnicalServiceDepartment
at 1-800-323-5190 for referral information.
When contacting your dealer or DESA In-
ternational, have ready:
• your name
• your address
• model and serial numbers of your heater
• how heater was malfunctioning
Portable Heater Parts
342 N. County Rd. 400 East
Valparaiso, IN 46383-9704
All States
219-462-7441
1-800-362-6951
Heater and Fireplace Store
58 Halbe Lane
Cape May Court, NJ 08210-1110
609-390-9774
Parts Department
•
type of gas used (propane/LP or natural gas)
Dayton Hardware
P.O. Box 275
North Dayton Station
Dayton, OH 45404-0275
All States
• purchase date
Usually, we will ask you to return the defec-
tive part to the factory.
FBD
1349 Adams Street
Bowling Green, KY 42103-3414
270-846-1199
1-800-654-8534
Fax: 1-800-846-0090
PARTS NOT UNDER
WARRANTY
937-258-3721
OH 1-800-762-3426
Contact authorized dealers of this product.
If they cannot supply original replacement
part(s), either contact your nearest Parts
Central or call DESA International’s Parts
Department at 1-800-972-7879 for referral
information.
Halco Enterprises
208 Carter Drive, Unit 21
West Chester, PA 19382-4500
610-430-7717
1-800-368-0803
Master Parts Dist.
1251 Mound Ave. NW
Grand Rapids, MI 49504-2672
616-791-0505
When calling DESA International, have
ready:
• model number of your heater
• the replacement part number
1-800-446-1446
Fax: 616-791-8270
LA Porte’s Parts & Service
2444 N. 5th Street
Hartsville, SC 29550-7704
803-332-0191
Washer Equipment Co.
1715 Main Street
Parts Department
Kansas City, MO 64108-2195
KS, MO, AR
Cans Unlimited, Inc.
P.O. Box 645
816-842-3911
Taylor, SC 29687-0013
All States
803-879-3009
1-800-845-5301
104268
17
Download from Www.Somanuals.com. All Manuals Search And Download.
VENT-FREE PROPANE/LP GAS HEATER
ILLUSTRATED
PARTS
22
21
BREAKDOWN
20
CGP10TA
CGP10TLA
10
14
16
13
19
23
12
24
18
10
4
11
14
15
7
9
6
3
5
17
8
2
1
12-1
12-2
ODS/PILOT
104268
18
Download from Www.Somanuals.com. All Manuals Search And Download.
OWNER’S MANUAL
This list contains replaceable parts used in your heater. When ordering parts, follow the
instructions listed under Replacement Parts on page 17 of this manual.
PARTS LIST
CGP10TA
CGP10TLA
KEY PART
NO.
NUMBER
DESCRIPTION
QTY.
1
2
098304-01
099467-02
099467-07
099318-04
101108-01
102017-02
098260-11
098532-06AA Top Glass Retainer
M11084-38 Screw, #8 x 3/8"
098352-03BR Deflector Unit
Screw, #10 x 3/8"
2
1
1
1
2
1
1
1
8
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
Front Panel Assembly (CGP10TA)
Front Panel Assembly (CGP10TLA)
Grill Guard
Grill Guard Clip
Bottom Glass Retainer
Glass Panel
3
4
5
6
7
8
9
10
11
12
098271-03
098249-01
099059-03
Ignitor Cable
Nut, M5
ODS/Pilot Assembly
Thermocouple
Ignitor Electrode
Burner
Pilot Tubing
Injector, 1 Piece
Hex Nut
Pressure Regulator
Burner Tubing
Regulator Tubing
Thermostat Gas Valve
Cabinet Assembly (CGP10TA)
Cabinet Assembly (CGP10TLA)
Piezo Ignitor
12-1 098514-01
12-2 098594-01
13
104263-01
099387-11
104259-06
NJF 8C
099415-13
104261-01
104264-01
098522-18
102571-06
102571-05
097159-04
099553-01
098303-02
14
15
16
17
18
19
20
21
22
23
24
Pilot Shield
Screw, #6 x 5/16"
PARTS AVAILABLE - NOT SHOWN
102471-01
100642-02
Control Position Label
Assembly, Hardware
1
1
104268
19
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY INFORMATION
KEEP THIS WARRANTY
Model
Serial No.
Date Purchased
Always specify model and serial numbers when communicating with the factory.
We reserve the right to amend these specifications at any time without notice. The only warranty applicable is our standard written warranty.
We make no other warranty, expressed or implied.
LIMITED WARRANTY
COMFORT GLOW VENT-FREE RESIDENTIAL GAS HEATERS
DESA International warrants this product to be free from defects in materials and components for two (2) years from the date of first
purchase, provided that the product has been properly installed, operated and maintained in accordance with all applicable instructions.
To make a claim under this warranty the Bill of Sale or cancelled check must be presented.
This warranty is extended only to the original retail purchaser. This warranty covers the cost of part(s) required to restore this heater
toproperoperatingconditionandanallowanceforlaborwhenprovidedbyaDESAAuthorizedServiceCenter. Warrantypart(s)MUST
be obtained through authorized dealers of this product and/or DESA International who will provide original factory replacement parts.
Failure to use original factory replacement parts voids this warranty. The heater MUST be installed by a qualified installer inaccordance
with all local codes and instructions furnished with the unit.
This warranty does not apply to parts that are not in original condition because of normal wear and tear, or parts that fail or become
damaged as a result of misuse, accidents, lack of proper maintenance or defects caused by improper installation. Travel, diagnostic cost,
labor, transportation and any and all such other costs related to repairing a defective heater will be the responsibility of the owner.
TOTHEFULLEXTENTALLOWEDBYTHELAWOFTHEJURISDICTIONTHATGOVERNSTHESALEOFTHEPRODUCT;
THIS EXPRESS WARRANTY EXCLUDES ANY AND ALL OTHER EXPRESSED WARRANTIES AND LIMITS THE
DURATION OF ANY AND ALL IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE TO TWO (2) YEARS ON ALL COMPONENTS FROM THE DATE OF FIRST
PURCHASE; AND DESA INTERNATIONAL’S LIABILITY IS HEREBY LIMITED TO THE PURCHASE PRICE OF THE
PRODUCT AND DESA INTERNATIONAL SHALL NOT BE LIABLE FOR ANY OTHER DAMAGES WHATSOEVER
INCLUDING INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Some states do not allow a limitation on how long an implied warranty lasts or an exclusion or limitation of incidental or consequential
damages, so the above limitation on implied warranties, or exclusion or limitation on damages may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.
For information about this warranty write:
INTERNATIONAL
2701 Industrial Drive
P.O. Box 90004
Bowling Green, KY 42102-9004
104268 01
104268-01
REV. C
02/00
NOT A UPC
Download from Www.Somanuals.com. All Manuals Search And Download.
|