Delta Electronics Network Card SPBD 1250A4Q1R User Manual

SPBD-1250A4Q1R  
Intelligent SFP Bi-Directional Transceiver  
Module for Gigabit Ethernet  
FEATURES  
z RoHS compliant  
z Digital Diagnostic SFF-8472 Compliant  
z Simplex LC connector with 1310nm  
Transmitter and 1490nm Receiver  
z Integrated with WDM filter to cut 1550nm and  
1650nm optical signal off  
z Single + 3.3V power supply and TTL logic  
interface  
z Bellcore GR-468 compliant  
z Laser class 1 product which comply with the  
requirements of IEC 60825-1 and IEC 60825-2  
Description  
The SPBD-1250xxxx series are hot pluggable  
3.3V Small-Form-Factor (SFP) Bi-Directional  
transceiver module designed expressly for  
high-speed communication applications that  
require rates of up to 1250Mbit/sec. It is compliant  
with the Gigabit Ethernet standards, as well as the  
SFP Multisource Agreement (MSA).  
Application  
z IEEE 802.3ah 1000BASE-BX10  
z Gigabit Ethernet Application  
z FTTx WDM Broadband Access  
z Switch to switch/backbone interface  
The SPBD-1250xxxx transceivers provide with  
the LC receptacle that is compatible with the  
industry standard LC connector. The transceiver is  
also compatible with industry standard RFT  
connector and cage. It also includes a LOS (Loss  
Of Signal) circuit that provides a TTL logic-high  
output when an unusable optical signal level is  
detected.  
Performance  
z SPBD-1250A4Q1R data link up to 10km in  
The module includes 1310nm un-cool FP laser,  
InGaAs PIN, Preamplifer and WDM filter in a  
high-integrated optical assembly for high-density  
system application. The SFP Bi-Directional  
transceiver can upgrade transmission capacity very  
convenient without installing new fibers.  
9/125um single mode fiber.  
1
Revision: S1  
03/12/2007  
DELTA ELECTRONICS, INC.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPBD-1250A4Q1R  
Note (4): Spectral Width (RMS)  
Transmitter Spectral Limits  
RMS spectral width(max)  
Center Wavelength  
1000Base-BX10-U  
4
3
2
1
0
nm  
nm  
1260  
1270  
1280  
1290  
1295  
1297  
1329  
1331  
1340  
1350  
1360  
2.09  
2.52  
3.13  
3.50  
3.06  
2.58  
1240  
1260  
1280  
1300  
1320  
1340  
1360  
1380  
Center Wavelength (nm)  
Note (5). Eye Mask definition  
1+Y3  
1
1-Y1  
0.5  
Y1  
0
-Y2  
1-X1  
1
1-X2  
X1 X2  
0
Normalized Time  
4. Specification of Receiver  
Parameter  
Input Optical Wavelength  
Receiver Sensitivity  
Symbol  
λIN  
Min.  
1480  
Typ.  
Max.  
1500  
-23  
Unit  
nm  
Note  
PIN-PD  
Note (1)  
PIN  
PSAT  
dBm  
dBm  
uW  
dBm  
dBm  
dBm  
dB  
Input Saturation Power (Overload)  
-3  
5.0  
-21.1  
-
-44  
0.5  
Receive Sensitivity OMA  
OMA  
Note (2)  
LOS-Deassert Power  
LOS-Assert Power  
LOS Hysteresis  
PA  
PD  
PA-PD  
-24  
Note (3)  
Note (4)  
2
6
-12  
Receiver Reflectance  
dB  
3
Revision: S1  
03/12/2007  
DELTA ELECTRONICS, INC.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPBD-1250A4Q1R  
Stressed Receive sensitivity  
-15.4  
44.8  
-13.5  
2.6  
dBm  
uW  
dBm  
dB  
ps  
ps  
ps  
MHz  
dB  
Stressed Receive sensitivity OMA  
Vertical Eye-closure Penalty  
Deterministic Jitter  
Total Jitter  
Output Data Rise/Fall time  
Receiver 3dB upper cutoff frequency  
V ECP  
DJ  
TJ  
170  
266  
260  
1500  
-43  
tr/tf  
Note (5)  
1260 to 1360nm  
Optical Isolation  
from  
External 1550 to 1560nm  
-33  
dB  
Source  
1640 to 1665nm  
-33  
dB  
Note (1). Measured with 1490nm, ER=9dB; BER =<10-12@PRBS=27-1 NRZ  
Note (2). Specified with minimum optical extinction ration of 9dB.  
Note (3). When LOS asserted, the data output is Low-level (fixed)  
Note (4). When the terminal is viewed from the optical path, the reflection toward the optical path of the  
optical signal with a central wavelength of 1480nm to 1500nm transmitted to terminal.  
Note (5). These are 20%~80% values  
5. Electrical Interface Characteristics  
Parameter  
Symbol  
Min.  
Typ.  
Max.  
Unit  
Note  
Transmitter  
Total Supply Current  
ICC  
VDT  
RIN  
A
2400  
120  
VCC  
0.8  
mA  
mVp-p  
Ohm  
V
V
V
Note (1)  
Differential Data Input Swing  
Differential line input Impedance  
Transmitter Disable Input-High  
Transmitter Disable Input-Low  
Transmitter Fault Output-High  
Transmitter Fault Output-Low  
Transmitter Fault Pull up Resistor  
Receiver  
500  
80  
2
0
2
100  
VDISH  
VDISL  
VTXFH  
VTXFL  
RTX_FAULT  
Note (2)  
VCC+0.3  
0.8  
0
4.7  
V
k  
10  
Note (3)  
Total Supply Current  
ICC  
VDR  
VLOSH  
VLOSL  
RRXLOS  
B
900  
VCC+0.3  
0.8  
mA  
mVp-p  
V
V
kΩ  
Note (1)  
Note (4)  
Differential Data Output Swing  
LOS Output Voltage-High  
LOS Output Voltage-Low  
Receiver LOS Load  
400  
2
0
4.7  
10  
Note (3)  
Note (1). A (TX)+ B (RX) = 300mA  
(A: Not include termination circuit; B: using a resister of 150between Data-output and ground)  
Note (2). There is an internal 4.7 to 10kpull-up resistor to VccT.  
Note (3). Pull up to VCC on host Board.  
Note (4). Internally AC coupled with CML output, but requires a 100Ohm differential termination at or  
internal to Serializer/ Deserializer.  
4
Revision: S1  
03/12/2007  
DELTA ELECTRONICS, INC.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPBD-1250A4Q1R  
6. Enhanced Digital Diagnostic Interface  
The memory map in the following describes an extension to the memory map defined in SFP MSA.  
The enhanced interface uses the two wire serial bus address 1010001X(A2h) to provide diagnostic  
information about the module’s present operating conditions.  
2 wire address 1010000 X (A0h)  
2 wire address 1010001 X (A2h)  
0
0
Alarm and Warning Thresholds  
(56 bytes)  
Serial ID Defined by SFP MSA  
(96 bytes)  
55  
56  
Cal Constants  
(40 bytes)  
95  
96  
95  
96  
Real Time Diagnostic Interface  
(24 bytes)  
Vender Specific  
(32 bytes)  
119  
120  
Vender Specific  
127  
128  
127  
128  
User Writable EEPROM  
(120 bytes)  
Reserved in SFP MSA  
(128 bytes)  
247  
248  
255  
Vender Specific  
(8 bytes)  
255  
7. Digital Diagnostic Monitor Accuracy  
Parameter  
Transceiver Internal Temperature  
Power Supply Internal Voltage  
TX Bias Current  
Accuracy  
Unit Calibration  
Note  
± 3℃  
TC=-5~+75℃  
Internal  
V
Internal  
VCC=3.3V±5%  
± 3%  
± 10%  
± 3dB  
± 3dB  
mA  
dBm  
dBm  
Internal Specified by nominal bias value  
Internal -9 to -3dBm  
Internal -23 to -3dBm  
TX Optical Power  
RX Optical Power  
Note. Temperature and Voltage is measured internal to the transceiver.  
5
Revision: S1  
03/12/2007  
DELTA ELECTRONICS, INC.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPBD-1250A4Q1R  
8. Pin Description  
SFP Transceiver Electrical Pad Layout  
Host Board Connector Pad Layout  
Pin Function Definitions  
Pin Num.  
Name  
VeeT  
TX Fault  
Function  
Plug Seq.  
Notes  
1
2
3
4
5
6
7
8
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
Transmitter Ground  
Transmitter Fault Indication  
Transmitter Disable  
1
3
3
3
3
3
3
3
1
1
1
3
3
1
2
2
1
3
3
1
Note (1)  
Note (2)  
Note (3)  
TX Disable  
MOD-DEF2 Module Definition 2  
MOD-DEF1 Module Definition 1  
MOD-DEF0 Module Definition 0  
Rate Select Not Connect  
LOS  
VeeR  
VeeR  
VeeR  
RD-  
RD+  
VeeR  
VccR  
VccT  
VeeT  
TD+  
Note (4), 2 wire serial ID interface  
Note (4), 2 wire serial ID interface  
Note (4), Grounded in Module  
Function not available  
Loss of Signal  
Note (5)  
Receiver Ground  
Receiver Ground  
Receiver Ground  
Inv. Received Data Out  
Received Data Out  
Receiver Ground  
Receiver Power  
Transmitter Power  
Transmitter Ground  
Transmit Data In  
Inv. Transmit Data In  
Transmitter Ground  
Note (6)  
Note (6)  
Note (7)  
Note (7)  
Note (8)  
Note (8)  
TD-  
VeeT  
Plug Seq.: Pin engagement sequence during hot plugging.  
6
Revision: S1  
03/12/2007  
DELTA ELECTRONICS, INC.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPBD-1250A4Q1R  
Notes:  
1) Circuit ground is internally isolated from frame (chassis) ground. Tx GND and Rx GND may be internally isolated  
within the TRx module.  
2) TX Fault is an open collector/drain output, which should be pulled up with a 4.7K~10Kresistor on the host board.  
Pull up voltage between 2.0V and VccT+0.3V. The output indicates Low when the transmitter is operating  
normally, and High with a laser fault including laser end-of-life. In the low state, the output will be pulled to less  
than 0.8V.  
3) TX disable is an input that is used to shut down the transmitter optical output. It is pulled up within the module  
with a 4.7 – 10 K resistor. Its states are:  
Low (0 – 0.8V):  
(>0.8, < 2.0V):  
High (2.0 – 3.465V):  
Open:  
Transmitter on  
Undefined  
Transmitter Disabled  
Transmitter Disabled  
4) Mod-Def 0,1,2. These are the module definition pins. They should be pulled up with a 4.7K – 10Kresistor on the  
host board. The pull-up voltage shall be VccT or VccR.  
Mod-Def 0 is grounded by the module to indicate that the module is present  
Mod-Def 1 is the clock line of two-wire serial interface for serial ID  
Mod-Def 2 is the data line of two-wire serial interface for serial ID  
5) LOS (Loss of Signal) is an open collector/drain output, which should be pulled up with a 4.7K – 10Kresistor.  
Pull up voltage between 2.0V and VccR+0.3V. When high, this output indicates the received optical power is  
below the worst-case receiver sensitivity. Low indicates normal operation. In the low state, the output will be  
pulled to less than 0.8V.  
6) RD-/+: These are the differential receiver outputs. They are AC coupled 100differential lines which should be  
terminated with 100(differential) at the user SERDES. The AC coupling is done inside the module and is thus  
not required on the host board.  
7) VccR and VccT are the receiver and transmitter power supplies. They are defined as 3.3V ±5% at the SFP  
connector pin. Recommended host board power supply filtering is shown below page. Inductors with DC  
resistance of less than 1 Ohm should be used in order to maintain the required voltage at the SFP input pin with  
3.3V supply voltage. When the recommended supply-filtering network is used, hot plugging of the SFP  
transceiver module will result in an inrush current of no more than 30 mA greater than the steady state value.  
8) TD-/+: These are the differential transmitter inputs. They are AC-coupled, differential lines with 100  
differential termination inside the module. The AC coupling is done inside the module and is thus not  
required on the host board. The inputs will accept differential swings of 500 – 2400 mV (250 – 1200  
mV single-ended), though it is recommended that values between 500 and 1200 mV differential (250 –  
600 mV single-ended) be used for best EMI performance.  
7
Revision: S1  
03/12/2007  
DELTA ELECTRONICS, INC.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPBD-1250A4Q1R  
9. Recommend Interface Circuit  
1uH  
1uH  
VCC  
3.3V  
Protocol Vcc  
DELTA SFP Module  
RES1  
10uF  
0.1uF  
VccT  
0.1uF  
10k Ohms  
Tx_Disable  
Tx_Fault  
Tx_Disable  
Tx_Fault  
TD +  
0.01uF  
Laser Driver  
100 Ohms  
Laser Diode  
TD -  
0.01uF  
VeeT  
Protocol IC  
SerDes IC  
VccR  
RES1  
10uF  
0.1uF  
RD +  
0.01uF  
0.01uF  
Preamp &  
Quantizer  
100 Ohms*  
Photo Diode  
RD -  
Rx_LOS  
VeeR  
Rx_LOS  
3.3V  
RES1  
RES1  
RES1  
Mod_def 2  
Mod_def 1  
Mod_def 0  
PLD / PAL  
EEPROM  
RES1 = 4.7k to 10k Ohms  
* Depands on SerDes IC used  
SFP Host Board Schematic  
Design criterion of the capacitor used is the  
resonant frequency and its value must be in the  
order of the nominal data rate. Short trace  
lengths are mandatory.  
Recommended Host Board Supply Filtering Network  
8
Revision: S1  
03/12/2007  
DELTA ELECTRONICS, INC.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPBD-1250A4Q1R  
10. Outline Dimensions  
Class 1 Laser Product  
XXXX nm Tx / Rx XXXX nm  
Week (52Weeks/Year) : 1月2日=01  
Transmitter Wavelength  
Latch Color Identifier  
Blue  
Violet  
1310nm  
1490nm  
9
Revision: S1  
03/12/2007  
DELTA ELECTRONICS, INC.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPBD-1250A4Q1R  
11. Regulatory Compliance  
Feature  
Test Method  
Reference  
Performance  
Electrostatic Discharge Human Body Model MIL-STD-883E Method 3015.7  
(ESD) to the Electrical  
Pins  
(HBM)  
EIA-JESD22-A114  
(1) Satisfied with  
electrical  
Machine Model (MM) EIA-JESD22-A115  
Electrostatic Discharge Contact Discharge  
IEC/EN 61000-4-2  
IEC/EN 61000-4-2  
characteristics of  
product spec.  
(ESD) to the Simplex  
Air Discharge  
Receptacle  
Radio Frequency  
Electromagnetic Field  
Immunity  
IEC/EN 61000-4-3  
(2) No physical damage  
FCC Part 15 Class B  
EN 55022 Class B  
(CISPR 22A)  
Electromagnetic  
Interference (EMI)  
FDA/CDRH  
FDA 21CFR 1040.10, 1040.11 CDRH File # 0420993  
Laser Eye Safety  
TUV  
IEC/EN 60825-1  
IEC/EN 60825-2  
IEC/EN 60950  
TUV  
Certificate  
#
R50032471  
TUV  
Component Recognition  
UL/CSA  
UL 60950  
UL File # E239394  
Appendix A. Document Revision  
Version No.  
Date  
2006-08-15 Preliminary datasheet  
2007-03-12 Change the specification of Optical Rise/Fall Time from 200ps to 260ps.  
Description  
S0  
S1  
10  
Revision: S1  
03/12/2007  
DELTA ELECTRONICS, INC.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Coleman Home Safety Product 4346 User Manual
Coleman Trimmer 2000004412 User Manual
Craftsman Blower 358794964 User Manual
Craftsman Lawn Mower 917272261 User Manual
Craftsman Work Light 315110990 User Manual
Crown Audio Stereo Amplifier VCA MC4A User Manual
Crystal Audiovideo Speaker System Series User Manual
Curtis DVD Player 2053 User Manual
Delta Electronics Power Supply SI54 User Manual
Desa Tech Fitness Equipment CSBNT User Manual