Installation Instructions
Discovery Wall Oven
For use with models: EO, MO and PO
Part No. 65433 Rev. G
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Before You Begin... ........................................................... 1 Planning the Installation................................................... 6
Important Safety Instructions .......................................... 1
Important Information About Safety Instructions.............. 1
Safety Symbols and Labels ............................................. 1
General Safety Precautions............................................. 2
Selecting the Location...................................................... 6
Cabinet Cut-Out ............................................................... 6
Cabinet Cut-Out (continued)............................................ 8
Electrical Specifications ................................................... 9
Customer Service Information......................................... 3 Installation Instructions.................................................... 9
If You Need Help.............................................................. 3
Appliance Data Plate ....................................................... 3
Product Specifications ..................................................... 4
Product Dimensions......................................................... 4
Parts List .......................................................................... 9
Electrical Service Installation ......................................... 10
Final Installation ............................................................. 12
Verify Proper Operation ................................................. 14
Installation Checklist ...................................................... 15
Notes................................................................................. 16
Before You Begin...
Important:
•
Installer: In the interest of safety and to minimize problems, read these installation instructions completely and care-
fully before you begin the installation process. Leave these installation instructions with the customer.
•
Customer: Keep these installation instructions for future reference and the local electrical inspector’s use.
Important Safety Instructions
Important Information About
Safety Instructions
Safety Symbols and Labels
DANGER
•
•
The Important Safety Instructions and warnings in
these instructions are not meant to cover all possible
problems and conditions that can occur. Use common
sense and caution when installing, maintaining or oper-
ating this or any other appliance.
Immediate hazards that WILL result in severe personal
injury or death.
WARNING
Always contact the Dacor Customer Service Team
about problems and conditions that you don’t under-
stand. See Customer Service Information.
Hazards or unsafe practices that COULD result in severe
personal injury or death.
CAUtION
Hazards or unsafe practices that COULD result in minor
personal injury or property damage.
DANGER
WARNING
IMPORtANt: Do not store or use combustible, flam-
mable, or explosive vapors and liquids (such as gasoline)
inside or in the vicinity of this or any other appliance. Also
keep items that could explode, such as aerosol cans,
away from the oven. Do not store flammable or explosive
materials in adjacent cabinets or areas.
WARNING – NEVER use this appliance as a space heat-
er to heat or warm the room. Doing so may result in car-
bon monoxide poisoning or overheating of the appliance.
WARNING
WARNING – NEVER cover any slots, holes or passages
in the oven bottom or cover an entire rack with materials
such as aluminum foil. Doing so blocks air flow through
the oven and may cause carbon monoxide poisoning.
WARNING
Do not install or use this product near water or outdoors,
for example, near a kitchen sink, in a wet basement or
near a swimming pool.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
General Safety Precautions
To reduce the risk of fire, electric shock, serious injury or death when using your appliance, follow basic safety precau-
tions, including the following:
WARNING
WARNING
1. Read the accompanying use and care manual
before operating this appliance.
15. To prevent injury due to the unit tipping forward,
secure the oven to the cabinet using the supplied
mounting screws.
2. Keep packaging materials away from children.
Plastic sheets and bags can cause suffocation.
16. Keep flammable items, such as paper, cardboard,
plastic and cloth away from hot surfaces. Do not put
such items in the oven. Do not allow pot holders to
touch hot surfaces.
3. If you receive a damaged product, immediately
contact your dealer or builder. Do not install or use
a damaged appliance. Do not install or use the
appliance if the conduit is damaged.
17. Do not wear loose or hanging apparel while using
the oven. Do not allow clothing to come into contact
with the interior of the oven and the surrounding
areas during and immediately after use.
4. This oven must be properly installed and
grounded by a qualified installer according to
these installation instructions prior to use. The
installer must show the customer the location of
the circuit breaker panel or fuse box so that they
know where and how to turn off electric power
to the oven. Dacor is not responsible for service
required to correct a faulty installation. The owner is
responsible to make sure this appliance is properly
installed.
18. Do not use the oven for storage.
19. Do not touch the interior surfaces of the oven during
use. After use, make sure these surfaces have had
sufficient time to cool before touching them.
20. Do not touch the outside surfaces of the oven
during the self-clean cycle. They will be hot. Venting
from the oven may cause the trim to become hot.
5. Do not lift or move the oven door by the handle(s).
21. For your safety, do not use the oven to cook without
the convection filter installed. When the filter is not
installed, the spinning fan blades at the back of the
oven are exposed.
6. A minimum of two people are required to safely
install this appliance.
7. To avoid an electric shock hazard, do not install this
appliance outside or near water. Do not install or
use this appliance if it has been exposed to water.
22. Non-stick coatings, when heated, can be harmful to
birds. Remove birds to a separate, well-ventilated
room during cooking.
8. Do not install, repair or replace any part of the oven
unless specifically recommended in the literature
accompanying it. A qualified service technician
must perform all other service.
23. To prevent damage, remove the meat probe from
the oven when it is not being used.
24. Do not line the oven with aluminum foil or other
materials. These items can melt or burn up during
self-cleaning and cause permanent damage to the
oven.
9. Before performing any type of service or
installation, make sure that the electric power to the
oven is turned off at the circuit breaker or fuse box.
10. Only use the oven for cooking tasks expected
of a home appliance as outlined in the literature
accompanying it. This oven is not intended for
commercial use.
25. Do not leave metal objects, such as aluminum foil,
the meat probe, cookie sheets, etc. on the bottom
of the oven. Objects left on the bottom of the oven
could damage the bake element. In addition, the
objects themselves could be damaged.
11. Do not climb on any part of the appliance.
12. Do not leave children or pets alone or unattended
in the area around the oven. Do not allow children
to play with the controls, pull on the handle or touch
other parts of the oven.
26. Do not allow heating elements in the top and
bottom of the oven chamber to become covered
up by cookie sheets, aluminum foil, pots, pans, etc.
Covering the heating elements could cause them to
over-heat, damaging the oven.
13. Do not store items of interest to children above the
oven. Children could be burned or injured while
climbing on the appliance.
27. Always ensure that the light fixture lens covers
are in place when using the oven. The lens covers
protect the light bulbs from breakage caused by
high oven temperatures or mechanical shock.
14. Do not tamper with the controls. Do not adjust
or alter any part of the oven unless specifically
instructed to do so in this manual.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Customer Service Information
Model Identification
If You Need Help...
•
If you have questions or problems with installation, con-
EO230xxx
tact your Dacor dealer or the Dacor Customer Service
Team. When you call, have the model and serial num-
ber of the appliance ready. The model and serial num-
ber are printed on the appliance data plate.
A C
B
D
Dacor Customer Service team
Phone:
E-mail:
Web site:
(800) 793-0093.
A = MODEL tYPE
Epicure Oven
= EO
Millennia Oven (vert. trim)
Millennia Oven (horiz. trim) = MOH
Preference Oven
= MOV
Appliance Data Plate
= PO
•
The appliance data plate contains the model and serial
number information and the electrical and gas supply
requirements.
B = CONFIGURAtION
Single Oven = 1
Double Oven = 2
•
It is located inside the oven door, in the slot above the
left hinge (inside the lower door on a double oven.) To
read the information on the data plate:
C = SIZE
1. Push the data plate tab.
2. Pull the data plate up.
27 Inch = 27
30 Inch = 30
Tab
D = FINISH
Finish Options
Epicure:
Stainless Steel, Black Chrome Trim
Stainless Steel, Chrome Trim
Stainless Steel, Brass Trim
= SBC
= SCH
= SBR
= SCP
Data
Plate
Stainless Steel, Copper Trim
Millennia:
Stainless Steel
Preference:
= S
Glass, Anthracite Gray
Glass, Black
Glass, Blue Water
Glass, Slate Green
Glass, Sterling Gray
Glass, Titanium Silver
= AG
= BK
= BU
= GN
= SG
= TS
IMPORtANt
Push the appliance data plate back into place before
closing the door.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Specifications
Product Dimensions
All tolerances are 1/16”, -0 (1.6 mm, -0)
Model
Number
K
L
M
N
P
Q
R
S
EO127
PO127
27”
25 3/8”
(686mm)
(644mm)
MOV127
MOH127
EO130
27 15/16”
(710mm)
26 3/8”
(670mm)
PO130
30”
28 3/8”
(762mm)
(721mm)
MOV130
MOV130
EO227
23 3/8”
(594mm)
2 5/16”
(59mm)
7 3/8”
(187mm)
6 3/8”
(162mm)
PO227
27”
25 3/8”
(686mm)
(644mm)
MOV227
MOH227
EO230
51 3/32”
(1298mm)
49 1/2”
(1257mm)
PO230
30”
28 3/8”
(762mm)
(721mm)
MOV230
MOH230
MILLENNIATM
EPICURE ®
PREFERENCE ®
3 11/16”
(94mm)
3 5/16”
(84mm)
2 5/16”
(59mm)
1 1/4”
1 1/4”
1 1/4”
(32mm)
(32mm)
(32mm)
22 11/16”
(576mm)
Handle Dimensions - All Models (Side View)
Door Dimension - All Models
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Specifications
“S”
“M”
“N”
“P”
1 1/4”
(32mm)
“Q”
“L”
“R”
1 1/16”
(27mm)
66”
(1676mm)
Flexible Conduit
“K”
Single Wall Oven Dimension
“S”
“N”
“M”
1 1/4”
(32mm)
“P”
“Q”
1 1/16”
(27mm)
“L”
“R”
66”
(1676mm)
Flexible Conduit
“K”
Double Wall Oven Dimension
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Planning the Installation
Model
Number
Selecting the Location
A
B
C
D
•
Carefully check the location where the oven is to be
installed. The oven should be placed for convenient
access, but away from drafts that may be caused
by doors, windows, and heating, ventilation and air
conditioning outlets.
EO127
PO127
25 1/2”
(648mm)
27”
56 1/2”
(686mm) (1435mm)
MOV127
MOH127
EO130
27 7/16”
(697mm)
•
Make certain that electrical power can be provided
in the selected location. Be certain that proper
clearance is provided for the oven door when it is in
the open position.
PO130
28 1/2”
(724mm)
30”
62 1/2”
(762mm) (1588mm)
MOV130
MOV130
EO227
Cabinet Cut-Out
PO227
25 1/2”
(648mm)
27”
(686mm)
•
•
•
Plan the installation so that all minimum clearances
are met or exceeded. Cutout dimensions shown
provide minimum clearances, unless otherwise
noted.
MOV227
MOH227
EO230
50 9/16”
(1284mm)
NA
The specified minimum cabinet depth and width
must be provided. The cabinet depth and width
must completely enclose the recessed portion of
the oven.
PO230
28 1/2”
(724mm)
30”
(762mm)
MOV230
MOH230
Cabinet cutout dimensions must be used as indi-
cated.
“C”
“C”
Recommended
Electrical
Location
Recommended
Electrical
Location
1“ (25mm)
Clear to Top
of Drawer for
Heat Exhaust
1“ (25mm) Min.
Clear to Top of
Door for Heat
Exhaust
Single Wall
Oven Cutout
“A”
“B”
“B”
Alternate
Electrical
Location
3/4” (19mm)
Support Platform
“A”
Double Wall
Oven Cutout
1 ¾“ (45mm) Min.
Clear to Top of
Door for Heat
Exhaust
31 1/4” (794mm)
Recommended
(May be Altered)
3/4” (19mm)
Support Platform
9 5/8” (244mm)
Recommended
(May be altered)
1 ¾“ (45mm)
Clear to Top
of Drawer for
Heat Exhaust
4“ Typical Toe Kick (Shown)
4“ Typical Toe Kick (Shown)
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Planning the Installation
“D”
NOtES:
•
•
•
All tolerances are 1/16”, -0 (1.6 mm, -0)
24” minimum cutout depth
3/4” support platform must be flush with
front of cutout. See page 8.
Recommended
Electrical
Location
Recommended
Electrical
Location
1“ (25mm) Min.
to Bottom of
Door
4“ (102mm) Min.
Between Cutout
Duel Single Wall Oven Cutout
“A”
“A”
“B”
“B”
3/4” (19mm)
3/4” (19mm)
Support Platform
Support Platform
Alternate
Electrical
Location
1 ¾“ (45mm)
Min. to Top of
Door for Heat
Exhaust
Alternate
Electrical
Location
31 1/4” (794mm)
Recommended
(May be Altered)
4“ Typical Toe Kick (Shown)
1“ (25mm) Min. to Combustibles
1 1/2”
(38mm)
Typical Counter
Single Wall Oven Under
Counter Cutout
36” Typical
(914mm)
“A”
“B”
Recommended
Electrical
Location
3/4” (19mm)
Support Platform
4“ Typical Toe Kick (Shown)
1 ¾“ (45mm) Min.
to Combustible Floor
1 1/2” (38mm)
Typical Counter
Recommended Electrical Location
1“ (25mm) Min. to Combustibles
4“ (102mm) Min.
Between Cutout
“A”
“A”
36” (914mm)
Typical
Duel Single Wall Oven
Under Counter Cutout
“B”
“B”
Alternate
Electrical
Locations
3/4” (19mm)
3/4” (19mm)
Support Platform
Support Platform
4“ Typical Toe Kick (Shown)
1 ¾” (45mm) Min.
to Combustible Floor
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Planning the Installation
Cabinet Cut-Out (continued)
Support Platform
WARNING
The top surface of the support platform must be installed
flush with the cutout in the front of the cabinet or wall
and any trim. Failure to install the platform properly
may cause the exhaust vent to deform and/or become
obstructed. An obstructed exhaust area may cause the
oven to malfunction. See below.
Provide a platform within the cabinet to support the oven.
A properly supported piece of 3/4” (19mm) thick plywood is
recommended.
All contact surfaces between the appliance and the cabi-
net, including the support platform, must be sturdy, straight
and level. The oven cannot be leveled after it has been
installed.
Oven Door
Cool Air Intake
(do not block)
Exhaust Deflector
(do not bend)
Deformed Sheet Metal
Blocking Vent
Support Platform
Exhaust Vent
do not block
Sheet Metal on
Bottom of Oven
Cabinet Front
or Wall
WRONG
RIGHT
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Planning the Installation
It is the owner’s responsibility to ensure that a qualified
Electrical Specifications
electrician performs the electrical connection of this appli-
ance. The electrical installation, including minimum supply
wire size, must comply with the National Electric Code
ANSI/NFPA 70 (latest revision) and local codes and ordi-
nances.
IMPORtANt
•
•
Preheat times and cavity temperature recovery times
will be increased slightly if operating on less than a
240 Vac circuit.
*A copy of this standard may be obtained from:
National Fire Protection Association
1 Batterymarch Park
Quincy, Massachusetts 02269-9101
This appliance is provided with electrical connec-
tion leads in a flexible metal conduit. These leads
may be a smaller gage than the standard household
wiring of the dedicated supply circuit, but they are
suitable for connection to these circuits under the
jurisdiction of the National Electric Code, and/or the
local inspection authority.
The correct voltage, frequency and amperage must be sup-
plied to the appliance from a dedicated, grounded, single
phase circuit that is protected by a properly sized circuit
breaker or time-delay fuse. If a time-delay fuse is utilized,
fuse both sides of the line (L1and L2).
•
Locate the junction box so that the wiring may be
disconnected without removing the oven from the
wall.
Dedicated Circuit
Required
total
Connected Load
Model type
Single 27”
Single 30”
Double 27”
Double 30”
240 Vac, 60 Hz
4 wire 30 Amp
Dedicated
4.6 kW (19.5 Amp)
9.25 kW (38.9 Amp)
240 Vac, 60 Hz
4 wire 50 Amp
Dedicated
The above electrical ratings are for reference only. For the
exact ratings see the appliance data plate. See page 3 for
location.
Installation Instructions
Parts List
Verify that all the parts are included. If any item is missing
or damaged, please contact your dealer immediately.
•
Exhaust deflector with three (3) screws
•
Mounting screws, four (4) for single ovens, six (6) for
double ovens, two (2) different sizes may be included.
Make certain that you have all tools and parts necessary to
ensure a proper installation before proceeding. If replace-
ments parts are required, contact your Dacor dealer.
•
Standard oven racks two (2) for a single oven, five (5)
for a double oven
•
•
•
•
•
•
•
•
•
•
GlideRack™ oven rack, one (1)
Broiler grill and pan
Meat probe, one (1)
Ceran cleaning kit
Stainless steel cleaner (stainless steel models only)
Light lens pry stick
Ease form
Quick start guide
Installation instructions
Use and care manual
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
1. Before proceeding, turn off power to the circuit to which
Electrical Service Installation
the oven will be connected at the circuit breaker or fuse
box.
WARNING
2. Position the oven directly in front of the cabinet cutout.
•
•
Wire the oven only in compliance with local ordi-
nances.
3. Feed the appliance conduit into the electrical junction
box and attach it using a UL approved strain relief.
If the electrical service provided does not meet
the product specifications, do not proceed with the
installation. Call a licensed electrician to install the
required wiring.
4. Depending upon local codes, utilize one of three meth-
ods to connect the appliance to the electrical power:
◊
◊
Connect to a four wire electrical system
Connect to a three wire electrical system, where
local codes permit
•
•
To prevent an electric shock or fire hazard, turn off
power to the circuit at the circuit breaker or fuse box
prior to connecting the wiring to the oven.
◊
Connect to a three wire electrical system with
external ground, according to local codes.
Improper connection of the electrical wiring can
cause an electric shock hazard and damage the
appliance. Dacor is not responsible for damages
resulting from improper installation.
Connecting to a Four Wire Electrical
System
1. Separate the wires coming out of the appliance conduit.
•
•
•
•
•
Connect the ground terminal (or lead) on the appli-
ance to a grounded, metallic, permanent wiring sys-
tem or grounding conductor.
2. Connect the white wire from the appliance conduit to
the white (neutral) supply wire in the junction box.
Do not use an extension cord with this appliance.
Such use may result in fire, electric shock or other
personal injury.
3. Connect the black wire from the appliance conduit to
the black (L1) supply wire in the junction box.
4. Connect the red wire from the appliance conduit to the
red (L2) supply wire in the junction box.
Do not install a fuse in the neutral or ground circuit.
A fuse in the neutral or ground circuit may result in
an electric shock hazard.
5. Connect the green wire from the appliance conduit to
the green (ground) wire in the junction box.
The appliance must be connected to the power sup-
ply with copper wire only. The use of aluminum wire
may result in unsatisfactory connections.
Cable from
power supply
Flexible armored or non-metallic, sheathed copper
cable (with grounding wire) should be used to con-
nect the appliance to the junction box. An UL-listed
connector must be used to directly connect the cable
to the junction box.
Junction
box
IMPORtANt
RED
Make sure that the conduit is long enough to allow the
oven to be pulled out for service without disconnecting it
from power.
WHITE
RED
WHITE
GREEN
BLACK
GREEN
BLACK
Wire nut
(4 places)
Conduit from
appliance
4 Wire Junction Box Connection
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
Connecting to a Three Wire Electrical
Connecting to a Three Wire Electrical
System with External Ground - Where Local
Codes Permit
System - Where Local Codes Permit
WARNING
WARNING
Do not connect the green appliance conduit wire to the
neutral (white) junction box wire unless local building
codes permit.
•
Do not connect the green appliance wire to the junc-
tion box or to a cold water pipe unless local building
codes permit.
1. Separate the wires coming out of the appliance conduit.
•
•
Do not ground the appliance to a gas supply pipe or
hot water pipe.
2. Connect the green and white wires from the appliance
conduit to the white (neutral) supply wire in the junction
box.
If connecting the ground wire to a grounded cold
water pipe, connect using a separate copper
grounding wire (No. 10 minimum) and a clamp with
an external grounding screw. The grounded cold
water pipe must have metal continuity to electrical
ground and must not be interrupted by insulating
materials. Any insulating materials must be jumped,
with a minimum, 4 AWG wire to establish continuity
to ground.
3. Connect the black wire from the appliance conduit to
the black (L1) supply wire in the junction box.
4. Connect the red wire from the appliance conduit to the
red (L2) supply wire in the junction box.
Cable from
power supply
No. 4
copper wire
Junction
box
Meter
GREEN
RED
WHITE
WHITE
RED
Metal
water pipe
Clamps
Bare metal
BLACK
BLACK
NOtE
Wire nut
(3 places)
If the junction box has been properly grounded by a
licensed electrician, the green (ground) wire from the
appliance conduit may be connected to the junction box
using a loop terminal.
See the diagram on the following page. To connect the
green appliance conduit wire to a grounded cold water
pipe:
Conduit from
appliance
1. Separate the wires coming out of the appliance conduit.
2. Connect the white wire from the appliance conduit to
the white (neutral) supply wire in the junction box.
3. Connect the black wire from the appliance conduit to
the black (L1) supply wire in the junction box.
4. Connect the red wire from the appliance conduit to the
red (L2) supply wire in the junction box.
5. Connect the green wire from the appliance conduit to a
grounded cold water pipe as shown. Jumper any insu-
lating materials as shown above with a length of No. 4
copper wire. Securely clamp the wire to bare metal at
both ends.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
Connecting to a Three Wire Electrical
System with External Ground - Where Local
Codes Permit (continued)
Cable from
Separate No. 10 (minimum)
copper grounding wire
power supply
Junction
box
RED
WHITE
RED
WHITE
GREEN
Clamp must be
tight on pipe
BLACK
GREEN
BLACK
Wire nut
(4 places)
Conduit from
appliance
Final Installation
WARNING
•
•
A minimum of two people are required to safely
install this appliance.
Do not attempt to disengage the hinge catches with
the door removed from the oven. The hinge springs
could release, causing personal injury.
•
•
Do not lift or carry the oven door by the door handle.
On double ovens: Remove the lower door first.
Otherwise, damage to the top of the lower door may
occur when the upper door is removed.
Remove the oven door(s)
Due to the weight of this appliance, remove the door(s) to
reduce the lifting load. Removing the door(s) will also pro-
vide a place to grip the oven when lifting it into place.
1. Open the oven door completely.
2. Pull the hinge locks forward on both hinges, until they
stop.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
3. Raise the door so that it is at a 15° angle from the front 2. Support the oven at all times until it is secured into the
of the oven. Hold the door with one hand on each side.
Lift the door up and out.
cabinet. Be certain to take all necessary safety precau-
tions.
3. Resting the oven on the cabinet support platform, slide
the oven into the recessed area until the rear edge of
the oven trim post is flush with the cabinet face and
the oven is centered within the cutout. Ensure that
the electrical conduit slides through the opening in the
cabinet platform or coils above the oven chassis as the
oven is slid into place. Do not trap the appliance cable
between the oven case back and the rear wall.
4. Make sure the oven is resting level. Shim it if neces-
sary.
Door Gripping
Points
WARNING
When installing the mounting screws into composite
cabinets, install them into the sides of the cabinet only.
Mounting screws installed into the front of composite
cabinets will have a tendency to pull loose.
Install the Oven in the Cabinet
WARNING
•
Use an appliance dolly to move the appliance when
installing it or removing it from the wall for service.
Use of an appliance dolly will minimize the risk of
personal injury as a result of the oven tipping.
5. Find the mounting hole locations in the front and side
of the oven trim posts. Drill 1/16” pilot holes in the cabi-
net through the front or side of the trim posts. Single
oven models require four (4) holes, while double oven
models require six (6).
•
•
Failure to install the mounting screws may result in
movement or tipping of the oven during use, or per-
sonal injury.
6. Install the #6 x 3/4” screws provided in the instructions
envelope. Do not over-tighten.
Do not block the oven air exhaust and intake located
at the bottom of the oven door(s). Blocking the air-
flow may cause cabinet damage and poor baking
performance.
IMPORtANt
An oven that is not level may provide poor or inconsistent
baking results.
1. Lift the oven up to the cabinet cutout using the handles
and gripping points shown. Use extreme caution when
lifting the appliance, because it is heavy.
Trim Post
Gripping Point
Handle
Trim Post
Gripping Point
Gripping Point
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
1. Grasp the oven door on opposite sides and hold it at a
Install Exhaust Deflector
15° angle from the front of the oven. See facing page.
2. Slide the hinges into the hinge openings, resting the
bottom of the hinge arms on the hinge receptacles.
CAUtION
Install the exhaust deflector before installing the oven
door(s).
3. Continue to hold the door at a 15° angle with one hand
while pushing in on each of the bottom corners of the
door. Push until the notch on the bottom of each hinge
slips over the lower lip of each hinge receptacle.
Attach the exhaust deflector to the front of the oven. It
attaches to the oven just below the oven chamber in the
door jam. On a double oven, the exhaust deflector is
mounted below the bottom oven chamber.
4. Lower the door to the fully opened position.
5. Rotate the two hinge locks toward the oven. Slowly and
carefully open and close the door completely to make
sure that it is properly installed.
1. Line up the mounting holes on the exhaust deflector
with the screw holes on the front of the oven.
2. Secure it using the three (3) screws provided.
Verify Proper Operation
WARNING
Read the accompanying use and care manual completely
before using the oven.
1. Remove any packaging from inside the oven(s).
2. On some models there is protective plastic coating over
the stainless steel surfaces. Peel them off before use.
3. Slide the oven racks onto the support racks in the oven
chamber(s) as instructed in the use and care manual.
4. Turn on the power to the oven at the circuit breaker or
fuse box. Set the clock as instructed int the use and
care manual.
5. Set the oven to bake mode as instructed in the use and
care manual.
NOtES: If the oven does not operate properly, follow these
troubleshooting steps:
•
•
•
•
Verify that power is supplied to the oven.
Check for proper electrical connection.
Repeat the above bake test.
If the appliance still does not work, contact the Dacor
Customer Service Team at (800) 793-0093.
Reinstall the Oven Door(s)
Do not attempt to repair the appliance yourself. Dacor
is not responsible for service required to correct a faulty
installation.
WARNING
To avoid damage to the door or personal injury from it
falling off its hinges:
•
Make sure that the notch on the bottom of each
hinge rests on top of the lower lip of each hinge
receptacle before attempting to open the oven door.
•
Rotate the hinge locks toward the front of the oven
immediately and completely after installation of the
door.
CAUtION
On double ovens: Install the upper door first to prevent
damage to the lower door.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
Lower lip of
hinge receptacle
Notch on bottom of hinge
Door Installation
Installation Checklist
□
□
Plastic coating, if applicable, has been removed from
outside of oven.
WARNING
•
To ensure a safe and proper installation, the follow-
All packaging materials have been removed from inside
the oven.
ing checklist should be completed by the installer
to ensure that no part of the installation has been
overlooked.
□
□
□
Power is turned on at circuit breaker or fuse box.
•
Proper installation is the responsibility of the hom-
eowner. The importance of proper installation of your
Dacor oven cannot be overemphasized.
Proper oven operation has been verified. See page 14.
Problems have been noted on the warranty card or dur-
ing the on-line activation. Warranty has been activated
on-line or the warranty card has been filled out com-
pletely and mailed.
□
Oven is wired to all applicable codes and Dacor specifi-
cations. See pages 9 and 10.
□
□
Oven is level. See page 13
Oven is secured into cabinet with included screws. See
page 13
□
□
Exhaust deflector has been installed. See page 14.
Oven door(s) have been properly re-installed. See
page 14.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Dacor ● 1440 Bridge Gate Drive, Diamond Bar, CA 91765 ● Tel: (800) 793-0093 ● FAX: (626) 403-3130 ● www.Dacor.com
Download from Www.Somanuals.com. All Manuals Search And Download.
|