ERWD, EWD, IWD, MRWD, MWDV, MWDH,
OWD, PWD Warming Drawers
24”, 27”, 30”, 36” Wide,
Warming Drawers
PLANNING
GUIDE
Revised
03/04/09
1/3
All tolerances: +1/16”, -0, (+1.6mm, -0) unless otherwise stated
WARNING
1. Observe all governing codes and ordinances during planning
and installation. Contact your local building department for
further information.
3/4" Min.*
(19 mm)
2.
This appliance must be installed in accordance with the
accompanying installation instructions.
Warming Drawer
Warming Drawer
C
C
36" Typ.
(914 mm)
D
120 Vac
electrical
receptacle
Electrical Circuit
Required
Total Connected
Load
3/4" Min.*
(19 mm)
120 Vac, 60 Hz, 15 Amp
grounddedicated circuit
A
B
0.5 kW (4.0 Amp)
ICAL REqUIREMENts
27"/30"/36"
Dacor
single oven
1 1/2" (38 mm)
Typical counter top
Cook
D
C
D
C
3/4” Min.*
(19 mm)
Warming Drawer
C
Warming Drawer
Warming Drawer
120 Vac
Elect.
3
120 Vac
electrical
receptacle
120 Vac
Elect.
A
B
Toe Kick
A
3/4" Min.*
(19 mm)
(D) Min. Vertical Gap
Between Cutouts
Min. Cutout
Depth
Model
(A) Cutout W
C) Cutout Height
ERWD30
EWD24
EWD27
EWD30
EWD36
IWD24
28 1/2”
22
25
28 1/2
34 1/2” (8
22 1/2” (572
25 1/2” (648 mm
28 1/2” (724 mm)
25 1/2” (648 mm)
28 1/2” (724 mm)
25 1/2” (648 mm)
28 1/2” (724 mm)
25 1/2” (648 mm)
28 1/2” (724 mm)
22 5/8” (575 mm)
25 1/2” (648 mm)
28 1/2” (724 mm)
m)*
2 mm)*
(768 mm)*
1/4” (921 mm)*
***
9 1/8” (232 mm)
9 1/8” (232 mm)
9 1/8” (232 mm)
9 1/8” (232 mm)
9 1/8” (232 mm)
9 1/8” (232 mm)
9 1/8” (232 mm)
9 1/8” (232 mm)
9 1/8” (232 mm)
9 1/8” (232 mm)
9 1/8” (232 mm)
9 1/8” (232 mm)
9 1/8” (232 mm)
9 1/8” (232 mm)
11 15/16” (303 mm)
9 1/8” (232 mm)
9 1/8” (232 mm)
1 1/4” (32 mm)*
1 1/4” (32 mm)*
1 1/4” (32 mm)*
1 1/4” (32 mm)*
1 1/4” (32 mm)*
***
IWD27
***
***
IWD30
***
***
24” (610 mm)
MRWD27
MRWD30
MWDH27
MWDH30
MWDV27
MWDV30
OWD24
PWD27
PWD30
27 1/4” (692 mm)*
30 1/4” (768 mm)*
27 1/4” (692 mm)*
30 1/4” (768 mm)*
27 1/4” (692 mm)*
30 1/4” (768 mm)*
24 1/4” (616 mm)**
27 1/4” (692 mm)*
30 1/4” (768 mm)*
1 1/4” (32 mm)*
1 1/4” (32 mm)*
1 1/4” (32 mm)*
1 1/4” (32 mm)*
1 1/4” (32 mm)*
1 1/4” (32 mm)*
3/4” (19 mm)**
1 1/4” (32 mm)*
1 1/4” (32 mm)*
20 1/8” (511 mm)
24” (610 mm)
CUtOUts DIMENsIONs
* Bare minimum spacing to allow for ventilation and avoid scraping on EWD, MW and PWD series models. See *** below for spacing
for IWD series or OWD24 with custom front panel.
** OWD24 with optional factory front panel kit only. Bare minimum spacing shown to allow for ventilation and avoid scraping. Gap
above and below cutout is 3/4” minimum.
*** On IWD series models or OWD24 without optional front panel kit: Height and width of custom front panel must exceed the chassis
face dimensions on page 3 to cover face of unit. Dimension (B) above = custom front panel width + 1/4” (6 mm). Dimension (D) above
= [custom front panel height - (C) Cutout Height] + 1/4” (6 mm) or 3/4” (19 mm) whichever is larger. Gap above and below cutout is
(D)/2 or 3/4” (19 mm) whichever is larger.
Corporate Phone: 800-793-0093
Specifications are subject to change without notice.
See installation instructions for additional details.
2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
ERWD, EWD, IWD, MRWD, MWDV, MWDH,
OWD, PWD Warming Drawers
24”, 27”, 30”, 36” Wide,
Warming Drawers
PLANNING
GUIDE
Revised
03/04/09
3/3
All tolerances: ±1/16” (±1.6mm) unless otherwise stated
C
B
E
D
Chassis
5/16”
(8 mm)
A
E DIMENsIONs
SerieS ShoWn)
Drawer open
F
40" (1016 mm)
3 prong
120 Vac power cord
Mounting hole,
9 places
OVERALL DIMENsIONs - IWD/OWD s
tOP VIEW
**
**
**
G
Chassis without
drawer installed
** = OWD24 mounting holes
CHAssIs DIMENsIONs
(iWD/oWD ShoWn)
(D)
(E)
(F)
(G)
Warming
Drawer
Model No.
(A) Dimension
Drawer Face
Width
(C) Dimension
Chassis Face
Width
(B) Dimension
Chassis Width
Dimension
Drawer Face
Height
Dimension
Chassis
Depth
Dimension
Drawer
Depth
Dimension
Chassis
Height
IWD24
IWD27
IWD30
22 5/16” (567 mm) 22 1/4” (565 mm) 22 3/8” (568 mm)
25 5/16” (643 mm) 25 1/4” (641 mm) 25 3/8” (645 mm)
28 5/16” (719 mm) 28 1/4” (718 mm) 28 3/8” (721 mm)
8 15/16”
(227 mm)
23 3/8”
(594 mm)
23 13/16”
(605 mm)
9 1/16”
(230 mm)
11 7/8”
(302 mm)
20”
(508 mm)
18”
(457 mm)
11 7/8”
(302 mm)
OWD24
22 1/2” (571 mm) 22 1/2” (571 mm) 22 1/2” (571 mm)
Corporate Phone: 800-793-0093
Specifications are subject to change without notice.
See installation instructions for additional details.
2.3
Download from Www.Somanuals.com. All Manuals Search And Download.
|