DVDO VCR VP50 User Manual

HIGH-DEFINITION VIDEO PROCESSOR & HUB  
DVDO by Anchor Bay Technologies, Inc.  
983 University Avenue, Building A  
Los Gatos, CA 95032 USA  
Tel: 866-423-DVDO (3836) Fax: 408-379-3845  
Customer Support  
Tel: 866-423-DVDO (3836) Extension 333  
Ow n e r S MAn u Al  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of ConTenTs  
seCTion ꢀ – GeTTinG sTarTed  
2
Introduction  
2
2
3
3
3
4
4
5
6
Unpacking and Inspection  
Display Compatibility Requirements  
Document Conventions  
Menu Navigation  
Remote Control Battery Installation  
Remote Control Overview  
Info Screen  
Installation Guidelines  
seCTion 2 – basiC operaTion  
7
7
Front Panel Overview  
Rear Panel Overview  
Video Inputs  
7
8
8
8
9
9
9
Video Outputs  
Audio Inputs  
Audio Outputs  
12V Trigger Outputs  
RS232 Serial Connection  
Power Supply Input  
9
seCTion 3 – seTup  
10  
Initial Set-Up  
10  
ꢀ0  
ꢀ0  
STEP 1 - Power Up  
STEP 2 - Connect the iScan VP50PRO to the Display  
STEP 3 - Selecting the Optimal Output Resolution on the  
iScan VP50PRO for the Connected Display(s)  
STEP 4 - Connecting the Sources to the iScan VP50PRO  
ꢀ0  
ꢀ2  
STEP 5 - Configuring the Sources to Get Maximum Performance ꢀ2  
STEP 6 - Deinterlacing Mode and PReP™  
ꢀ4  
ꢀ5  
ꢀ5  
ꢀ6  
STEP 7 - Assigning Audio Inputs to Video Inputs  
STEP 8 - Display Optimization – Using Display Adjustments  
STEP 9 - Source Optimization – iScan Adjustments  
Download from Www.Somanuals.com. All Manuals Search And Download.  
i sCan Vp50pro  
Table of ConTenTs  
Advanced Setups  
17  
Configuration  
Test Patterns  
26  
Configuring the iScan VP50PRO for projectors with  
26  
26  
26  
27  
27  
27  
27  
27  
27  
anamorphic lenses  
Configuring the iScan VP50PROto output 24/48/72Hz  
Auto Standby  
LED Brightness  
User Mode  
and 25/50/75Hz  
Serial Port Rate  
Factory Default  
Software Update  
12V Trigger Levels  
Information  
seCTion 4 – Menu opTions  
18  
18  
Input Select  
Output Setup  
27  
Input Aspect Ratio Control  
Frame Aspect Ratio  
Active Aspect Ratio  
Panorama  
18  
ꢀ9  
ꢀ9  
ꢀ9  
20  
20  
20  
2ꢀ  
Analog/Digital  
Output Format  
Output Aspect Ratio Control  
Sync Type  
28  
28  
28  
30  
30  
30  
30  
32  
32  
32  
32  
33  
Zoom  
Color Space  
Pan  
Output Level  
Borders  
Framerate Conversion  
Border Level  
Presets  
Picture Controls  
HDCP Mode  
Input Adjust Control  
Mosquito Noise Reduction  
Deinterlacing  
22  
22  
22  
23  
23  
23  
23  
23  
24  
24  
24  
24  
25  
25  
12V Triggers  
Display Profiles  
PReP™, Progressive ReProcessing  
Pass Through  
Overscan  
seCTion 5 – CoMpleTe Menu Tree  
34  
Image Shift  
Color Space  
Input Level  
VCR Mode  
HDMI Configuration  
Auto Input Priority Selection  
Audio Input  
AV Lip Sync™  
Picture Controls  
25  
Fine Detail  
25  
25  
25  
25  
25  
26  
26  
26  
Edge Enhancement  
Brightness  
Contrast  
Saturation  
Hue  
Y/C Delay  
Chroma Filter (Auto CUE-C™)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
seCTion ꢀ – GeTTinG sTarTed  
Introduction  
Thank you for purchasing the iscan Vp50pro video processor, the first VRS (Video Reference  
series) component available with:  
Mosquito noise reduction  
fine detail enhancement™  
edge enhancement  
Vrs Technologies included in the iscan Vp50pro are:  
ꢀ0-bit precision deinterlacingof 480i/576i/ꢀ080i  
ꢀ0-bit precision Video scalingup to ꢀ080p  
prep, progressive reprocessing of 480p/576/ꢀ080p  
progressive Cadence detectionof 480p/576p/720p/ꢀ080p  
rightrateHigh performance frame rate Conversion  
in addition to our own award winning video processing technologies, the iscan Vp50pro also  
offers a host of other innovative features, including:  
4 HDMI 1.3 (High Definition Multimedia Interface) Inputs and 1 HDMI 1.3 Output  
THX Video Certification  
ISF ccc Certification  
2 programmable ꢀ2 V Triggers to control other devices  
This owners Manual can help you set up your iscan Vp50pro, and give you the information  
required to understand the total. it can also show you how to properly connect it and use it with  
the other components in your system.  
Unpacking and Inspection  
please verify that your iscan Vp50pro carton contains the following items:  
iscan Vp50pro Video processor  
universal 6V@7a aC-to-dC power Converter  
US IEC Power Cord (International Customers, consult your local authorized  
dVdo reseller)  
remote Control  
iscan Vp50pro owners Manual  
iscan Vp50pro Quick start Guide  
Serial Cable for Software Updates and Automation (1:1)  
VRS Optimization & Evaluation DVD  
dVdo software Cd  
rack Mount Kit  
RCA-to-BNC Adapters (5)  
if you are missing any items, please contact your dealer or the dVdo support Team.  
The iscan Vp50pro uses bnC-style analog connectors and an HdMi digital connector to provide  
video output signals. five rCa-to-bnC adapters are included to facilitate using the analog input or  
output with a cable terminated with rCa connections. additional cables or adapters are required  
to connect the iScan to your source(s) and display(s). Different displays have different input  
connectors, so check your display specifications to ensure compatibility.  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
Both input and output cables can be supplied by your Authorized DVDO Reseller. To nd your  
nearest Authorized DVDO Reseller, go to www.anchorbaytech.com. There are also a wide selection  
of cables and adapters available directly from anchor bay.  
Menu Navigation  
The iscan Vp50pro can be controlled the following ways:  
from the front panel controls  
from the iscan Vp50pro remote control  
from a programmed universal remote control  
using the serial connection on the back panel  
Display Compatibility Requirements  
dVdo iscan video processing products are compatible with a wide range of displays. These include  
digital TVs, projectors, and flat panel displays, as well as other emerging technologies that can  
support 480p or higher resolution video signals. To determine if your display is compatible with the  
dVdo iscan Vp50pro, look to see if it has an HdMi or dVi digital video input. if not, then your display  
may only have analog High Definition inputs or it is probably limited to receiving a standard NTSC, PAL  
or seCaM interlaced signal and will not function correctly with Vp50pro. High Definition Analog inputs  
include Component Video (YPbPr) and RGBHV using HD15 and/or 5 BNC terminated coaxial cables.  
Component inputs that are not capable of accepting a 480p signal, at a minimum, are usually labeled  
‘480i’ (NTSC) or ‘576i’ (PAL/SECAM).  
The menu navigation controls on the remote control are duplicated on the frontpanel of the iscan Vp50pro  
.
To navigate the menu:  
ꢀ. press the Menu button.  
2. use the directional buttons (t,p,q,u) to highlight the parameter you want to change.  
3. press the Enter or ubutton to select the parameter and the pand qbuttons to change  
the chosen parameter. press the tbutton to stop adjusting a parameter and to return  
to navigating the osd.  
The following types of fixed-pixel displays with digital video inputs should be compatible with the  
iscan Vp50pro since a large majority of them can support higher resolution signals:  
4. press the Exit button to exit out of the menu/OSD  
plasma displays  
LCD-based flat panel and front & rear projection displays  
DLP-based front & rear projection displays  
Remote Control Battery Installation  
The remote control uses two aaa batteries, which should be replaced as needed. Two aaa batteries  
are included.  
LCoS-based front & rear projection displays (D-ILA™ & SXRD™ included)  
To install the remote control batteries:  
Document Conventions and Menu Navigation  
ꢀ. locate the battery compartment on the back of the remote control.  
in this owners Manual, an action that requires navigating the menu system of the iscan Vp50pro  
is referred to in the following abbreviated form:  
2. remove the cover from the back. To do this, press the tab attached to the cover and pull the  
cover with the guide on the back of the remote control.  
Picture Control  
Brightness  
_ _  
5
3. Remove the old batteries (if applicable).  
For example, to adjust the ‘Brightness’ to a value of ‘5, press Picture Control and then press qthree  
times, highlighting ‘Brightness’ in the on screen display (OSD) or if you are looking at the front panel  
display (FPD) you will see ‘Picture Control’ on the top line and ‘Contrast’ on the bottom line. This is  
abbreviated as ‘Picture Control / Contrast. Next press uto adjust the setting and then press puntil  
the value is ‘5. Finally press Exit.  
4. insert two new aaa batteries in the compartment as shown on the inside of the battery  
compartment. Make sure the batteries are correctly inserted, observing the proper polarity.  
5. After installation, replace the cover and dispose of the old batteries (if applicable).  
Text that is in bold refers to a button on the remote control of front panel of the iscan.  
Text that is in ‘quotes’ references an item that is in the On Screen Display.  
Text that is in italics references other sections of this owners Manual.  
The t, u,q, and psymbols refer to the navigational keys on the remote control and the front panel  
of the iscan.  
3
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Curtain Button  
Remote Control Overview  
The iscan Vp50pro remote has a Curtain button which allows you to close a ‘curtainover the image.  
This feature is especially useful when an image is paused on a display susceptible to burn-in or a tran-  
sition while switching inputs as part of a macro on a universal remote or automation system.  
for additional information about the functions of these buttons, turn to the pages given in  
parentheses ( ).  
Curtain  
6
Info  
5
Discrete IR Codes and Serial Automation Protocol  
STANDBY  
POWER  
INFO  
CURTAIN  
Almost all commands that are available in the On Screen Display can be executed discretely using a  
programmable ir remote control or automation system connected via an rs232 serial connection.  
These codes are available at www.anchorbaytech.com  
Power  
Standby  
5
5
Test Patterns  
(Left, On/Off, Right)  
Output Setup  
Configuration  
Picture Control  
Input Adjust  
28  
26  
25  
22  
26  
OUTPUT  
SETUP  
ON/OFF  
Display Profiles  
17  
TEST PATTERN  
CONFIG  
Viewing Modes  
32  
21  
Input Aspect  
Non-Volatile Memory Settings  
Ratio  
Exit  
PICTURE  
CONTROL  
The iscan Vp50pro stores a variety of user settings in non-volatile memory. non-volatile memory  
retains its contents when power is lost. There is one group of system settings and one group of user  
settings.  
DISPLAY  
PROFILES  
VIEWING  
MODES  
INPUT  
ASPECT  
RATIO  
INPUT  
MEMORIES  
ADJUST  
MENU  
EXIT  
Menu  
4
4
4
ENTER  
Border  
20  
Crop  
Pan  
Installation Guidelines  
*
BORDER  
CROP  
Take special care with the iscan Vp50pro installation to ensure optimal performance. pay particular atten-  
tion to the bulleted items that begin below and to other precautions that appear throughout this guide.  
Aspect  
18  
Zoom  
20  
21  
20  
ZOOM  
PAN  
4:3  
ASPECT  
16:9  
21  
HDMI 1  
HDMI 2  
4:3  
16:9  
SDI  
Do . . .  
18  
COMP 1  
S-VIDEO 1  
VIDEO 1  
VIDEO 2  
Input Select  
install the iscan Vp50pro on a solid, flat, level surface such as a table or shelf.  
You can also install the iScan VP50pro in a standard ꢀ9” equipment rack using an optional  
rack-mount kit available from authorized DVDO resellers or directly from DVDO.  
(HDMI 1, HDMI 2, HDMI 3, HDMI 4,  
Component 1, Component 2,  
RGBHV/Component,  
HDMI 3  
HDMI 4  
COMP 2  
RGBHV  
S-VIDEO 2  
S-Video 1, S-Video 2,  
Video 1, Video 2, AUTO)  
AUTO  
INPUT SELECT  
select a dry, well-ventilated location.  
Use only the included external power supply.  
Avoid excessive humidity, sudden temperature changes or temperature extremes.  
Use only accessories recommended by the manufacturer to avoid fire, shock or other hazards.  
unplug your Vp50pro before cleaning. use a damp cloth for cleaning.  
An asterisk (*) indicates a feature that has not yet been implemented.  
Don’t . . .  
install the iscan Vp50pro on an unstable surface or one that is unable to support all  
four of its feet, unless it is installed in an equipment rack.  
Power/Standby Buttons  
The iscan Vp50pro remote has a Power and a Standby button. The Power button always turns the  
iscan Vp50pro on and the Standby button always put the unit into standby mode.  
stack the iscan Vp50pro directly above heat-producing equipment such as power  
amplifiers or other components that generate heat during use.  
Info Button  
Expose the iScan VP50pro to a high temperatures, humidity, steam, smoke, dampness,  
or excessive dust. Avoid installing the iScan VP50pro near radiators and other heat  
producing appliances.  
This iscan Vp50pro has an ‘infoscreen which brings up a window on the connected display which  
contains important input and output information which can help with troubleshooting. The software  
version which is loaded in the unit will also be displayed on this window and on the front panel display  
of the iscan.  
install the iscan Vp50pro near unshielded TV or fM antennas, cable TV decoders, and  
other rf -emitting devices that might cause interference.  
place the iscan Vp50pro on a thick rug or carpet or cover the iscan Vp50pro with cloth.  
This might prevent proper cooling.  
Attempt to service this unit. Instead, disconnect it and contact your Authorized DVDO  
reseller or contact anchor bay Technologies directly.  
open or remove unit panels or make any adjustments not described in this manual.  
Attempting to do so could expose you to dangerous electrical shock or other hazards.  
it may also cause damage to your iscan Vp50pro  
.
obstruct the front panel ir receiver window shown in “remote Control overview.  
do not attempt to use the remote control out of line of sight with the ir receiver.  
doing so will cause improper operation.  
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
seCTion 2 – basiC operaTion  
Video Inputs  
The iscan Vp50pro has eleven (11) video inputs. Most popular formats are supported on each  
input.  
Front Panel Overview  
Video Inputs  
The iscan Vp50pro has eleven (11) video inputs.  
Status LED  
IR Window  
Front Panel Display (FPD)  
Enter  
Navigation Keys  
Up  
Menu  
Exit  
The formats, colorspace and bit-depth that the inputs support are as follows:  
MENU  
EXIT  
Video and Video 2  
— formats: nTsC, pal, pal-M and seCaM  
s-Video and s-Video 2  
— formats: nTsC, pal, pal-M and seCaM  
Component/rGbs ꢀ and Component/rGbs 2  
— formats: 480i/p-60, 576i/p-50, 720p-50/60, ꢀ080i-50/60  
— Colorspace: YPbPr and RGBS  
On/Standby  
Left Down Right  
status led – This displays the current state of the iscan Vp50pro  
rGbHV/Component  
— formats: 480p-60, 576p-50, 720p-50/60, ꢀ080i-50/60, VGa/sVGa/XGa/sXGa-60  
— Colorspace: RGBHV and YPbPr  
off = The unit is in standby mode  
red = no signal detected  
HdMi ꢀ, HdMi 2, HdMi 3 and HdMi 4  
blue = The unit is processing the signal  
blinking blue = There is a problem with HdCp authentication  
Green = The unit detects an unsupported signal  
— formats 480i/p-60, 576i/p-50, 720p-50/60, ꢀ080i-50/60, ꢀ080p-24/25/30/50/60,  
VGa-60, sVGa-60, XGa-60, sXGa-60  
— Colorspace RGB/YCbCr 4:4:4/YCbCr 4:2:2  
— bit-depth: 8/ꢀ0 processed up to ꢀ2-bit passthrough  
blinking Green = in pass Through there is a problem with HdCp authentication  
on/standby button – This toggles unit power between on and standby.  
Video Outputs  
The iscan Vp50pro has two video outputs, one analog and one digital. The analog output on the  
iscan Vp50pro can output the following signal types:  
ir Window – This is where all ir commands are received by the iscan. do not obstruct this window.  
Front Panel Display (FPD) – This is where all information from the on screen display (OSD) is  
YPbPr (Component)  
rGbHV  
duplicated to assist in the setup of your iscan.  
rGsb  
NOTE: When navigating the Menu, the Front Panel Display (FPD) always shows the current selec-  
tion on the bottom line and the menu/submenu item on the top line. When you change a value of a  
setting, the value is on the bottom line and the title of the parameter is on the top line.  
rGbs  
The HdMi digital video output can output the following signal types:  
navigation buttons – These buttons are available both on the front panel and on the remote control.  
rGb 4:4:4  
YCbCr 4:2:2  
YCbCr 4:4:4  
NOTE: Switching Inputs using the Navigation buttons – You can switch inputs on the front panel of  
the iscan Vp50pro or using the remote using the navigation buttons. To do this, press the or ▲  
without pressing the Menu button first.  
To connect the iscan Vp50pro to a display that has a dVi input, use either an HdMi-to-dVi cable  
or an adapter.  
Back Panel Overview  
Optical  
Digital  
Output  
Optical  
RGBHV/Component  
Input  
Digital Input Analog Audio  
12V Triggers HD-SDI Inputs (Optional)  
Component/RGBS 1  
S-Video1 Video 1  
1 & 2  
Input  
1 &2  
1 &2  
Audio Inputs  
There are nine (9) audio inputs on the iScan VP50pro  
:
L
R
Y (G)  
Pb (B)  
Pr (R)  
H
V
Y (G) Pb(B) Pr (R)  
I
1
3
2
N
P
U
T
DC In  
Two (2) Optical Digital inputs  
Two (2) Coaxial Digital inputs  
One (1) Analog (L/R) input  
Four (4) HDMI 1.3 inputs  
I
1
2
1
1
2
1
2
OUTPUT  
INPUT  
ANALOG AUDIO INPUT  
N
P
U
T
O
U
T
1
2
3
4
P
U
T
S
2
4
HDMI  
ANALOG VIDEO  
POWER  
SYNC  
COMPONENT  
S-VIDEO  
VIDEO  
DIGITAL AUDIO  
SERIAL PORT  
HDMI Output  
HDMI Inputs  
1–4  
RGBHV/Component  
Output  
Power  
Component/RGBS 2  
S-Video2 Video2  
Coaxial  
Digital  
Output  
Coaxial  
Digital Input  
3 & 4  
Serial Port  
While the digital and analog audio inputs can be assigned to any one of the video inputs, the HdMi  
audio inputs are tied directly to the HdMi video signal connected on the same input.  
7
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
The iscan Vp50pro accepts digital audio sourced from dVd players, satellite receivers, digital set top  
boxes, HD-DVD players, Blu-ray players, game consoles, and other video components with digital  
audio. These inputs are compatible with most consumer digital audio formats, including Cd-audio  
(44.1kHz/16 bit LPCM), Dolby Digital, and DTS. The coaxial digital audio inputs are compatible with  
any format with a sampling frequency between 24kHz and 192kHz, and with a data word structure up  
to 24 bits in length. The optical digital audio inputs are compatible with any format with a sampling  
frequency between 24kHz and 96kHz and with a data word structure up to 24 bits in length.  
seCTion 3 – seTup  
STEP 1 - Power Up  
1. Attach the removable power cord to the external power supply.  
2. plug the removable power cord into a wall outlet or power conditioner, if applicable.  
3. plug the small connector attached to the cable that comes out of the power supply into  
the iscan. The iscan should power on and display ‘dVdo iscan Vp50pro / by anchor bay’  
on the Front Panel Display (FPD). If this does not happen, check all connections and  
verify that the power outlet does supply power with another device.  
The HdMi audio inputs are compatible with all of the HdMi ꢀ.3 audio formats.  
IMPORTANT: Use only the power supply that came with your iScan VP50PRO, or a  
replacement procured directly from Anchor Bay  
Audio Outputs  
There are two discrete digital audio outputs, one coaxial and one optical. Both are active at the same  
time, with the selected input audio stream.  
The HdMi ꢀ.3 output carries both audio and video.  
STEP 2 - Connect the iScan to the Display  
Displays with a DVI or HDMI Input  
12V Trigger Outputs  
There are two ꢀ2-volt trigger ports that are designed to supply a combined total of 500ma.  
based on the factory default settings, just connecting an iscan to a display with an HdMi or  
dVi input should complete this step as the default output is for the HdMi output to be active with  
a rGb 4:4:4 signal which is the standard signal for a dVi/HdMi connection. press the Menu  
button once to confirm that you can see the On Screen Display (OSD).  
RS232 Serial Connection  
This connection is used as an interface to control the iscan Vp50pro with an automation system and  
to update the software in the iscan Vp50pro. The most current software version is available at www.  
anchorbaytech.com.  
Displays without a DVI or HDMI input:  
follow steps ꢀ-4 for a Component input and steps ꢀ-8 for an rGbHV input  
Press the Menu button on the front panel of the iScan once. You should see ‘MAIN MENU / INPUT  
seleCT’ on the fpd.  
Power Supply Input  
ꢀ. press the Output Setup button once. You should see ‘MAIN MENU / OUTPUT SETUP’  
on the fpd.  
The iscan Vp50pro comes with a 6V@7a aC-to-dC converter power supply, which accepts ꢀ00-240  
VAC at 50/60Hz.  
2. press the ubutton. You should see ‘OUTPUT SETUP / Analog/Digital’ on the FPD.  
3. press the pbutton and you should see ‘Analog/Digital / HDMI (Digital). Press the p  
button once so that ‘Analog/Digital / BNC (Analog)’ is displayed on the FPD.  
press the enter button.  
4. You should now see the OSD  
5. press the qbutton one time and you should see ‘ouTpuT seTup / format’ on the fpd.  
6. press the ubutton one time to enter the format menu.  
7. press the qbutton until you see ‘format / VGa’ and then press the enter button.  
8. You should now see the OSD  
STEP 3 - Selecting the Optimal Output Resolution on the iScan for  
the Connected Display.  
Once you have installed the iScan into the system, you must properly configure it for the display  
device being driven. if the osd is not visible on the display’s screen when you press one of the  
menu or sub-menu (Output Setup/Config./Picture Control/Input Adjust) buttons on the remote  
control, then you must complete step 2 before continuing.  
determine the optimal output resolution to set the iscan to get the best picture from the display.  
To do this correctly, the native resolution or maximum resolution of the display must be known.  
Native resolution refers to the actual pixel count of a fixed pixel display. Fixed pixel display technolo-  
gies include plasma, lCd, dlp and lCos. CrT-based technologies use scan lines so they do not have  
a native resolution but they do have a maximum resolution.  
9
ꢀ0  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Keep in mind that some displays do not accept their native resolution and almost all HdTVs will  
accept 720p and 1080i resolutions, but no fixed pixel display has a native resolution of 1080i.  
in almost all cases, the picture will be better if one of these displays is sent a 720p signal instead  
of a ꢀ080i signal.  
is the correct output resolution for the display. also check to make sure that the display is in the  
correct aspect ratio mode, which may be causing the display to do additional unnecessary scaling.  
The correct mode may be called ‘native, dot-by-dot, full, or ‘anamorphic.  
NOTE: if this test pattern does not appear as it should, and you have chosen the native resolution  
of the display, you may not be able to bypass the internal processing on the display. This does not  
mean that the iscan can not still make an improvement in the image quality. in these cases select  
To change the output resolution, press the output setup button on the remote and navigate down to  
‘format. press uonce and select the desired output resolution.  
the closest output format to the display’s native resolution.  
Output Setup  
Format  
_ _  
(Make Selection)  
These are the most likely resolutions for the available display technologies.  
Vertical Lines  
The ‘Vertical Lines’ test pattern should appear as one pixel wide black and white columns. If you see  
any irregular pattern(s) in the image, you know that the display is scaling the signal horizontally.  
Plasma  
DLP  
37-43” – 852x480, 1024x768 and 1024x1024  
50-65” – 1280x768, 1360x768, 1365x768, 1366x768, 1080p-24/48/60  
rear projection – 720p-60 ꢀ080p-24, ꢀ080p-60  
Horizontal Lines  
Front Projection – 852x480, XGA, 720p-60, 1080p-24/48/60  
The ‘Horizontal Lines’ test pattern should appear as one pixel tall black and white rows. If you see  
any irregular pattern(s) in the image then you know that the display is scaling the signal vertically.  
LCD  
Rear Projection – 720p-60 and 1366x768  
Front Projection – XGA, 720p-60 1366x768 and 1080p-24/60  
Direct View – XGA, 720p-60, 1366x768 and 1080p-60  
STEP 4 - Connecting Your Sources  
LCoS/SXRD  
Rear Projection – 720p-60, 1366x768 and 1080p-60  
up to ꢀꢀ video sources can be connected to the iscan Vp50pro  
Front Projection – XGA, 720p-60, 1080p-24/60, 1400x788 and 1400x1050  
use the following suggestions for connecting several popular sources to the iscan  
CrT  
rear projection – 480p, 540p and ꢀ080i-60  
Front Projection – 720p-60, 1080p-60, 1280x960, 1440x960 and 1440x1152  
SD-DVR/STB – S-Video/Composite and Optical/Coaxial/Analog audio  
HD-DVR/STB – HDMI or DVI/Component and Optical/Coaxial audio  
NOTE: driving a CrT front projector beyond its capabilities may cause damage. Check with anchor  
bay if you are unsure of the display’s capabilities.  
DVD Player/Recorder – HDMI or DVI/Component and Optical/Coaxial audio  
HD-DVD Player – HDMI or Component and Optical/Coaxial audio  
Blu-Ray Player - HDMI or Component and Optical/Coaxial audio  
VCr – Composite/s-Video and analog audio  
Test Patterns to Use:  
Frame Geometry (Adjusting for Overscan)  
LD Player – Composite/S-Video and Optical/Coaxial audio  
When this test pattern is displayed correctly, there should be a one-pixel wide white border around  
the edge of the screen: If it is not sized correctly, it means that the display is overscanning the input  
signal. This is very common and is known for cutting off sports scores at the bottom of the screen.  
Use the ‘Underscan’ control to shrink the size of the output image so that you can see all of the  
active area of the signals coming from your sources. if it is also not positioned correctly, use the  
‘image shift’ controls to position it correctly. These controls are available under the aspect ratio  
setting in the output setup menu.  
Xbox – Component and Optical audio  
Xbox360 – Component/RGBHV and Optical audio  
Xbox360 Elite – HDMI or Component and Optical audio  
ps2 – Component and optical audio  
ps3 – HdMi or Component and optical audio  
Wii – Component and optical audio  
apple TV – HdMi or Component and optical audio  
Checkerboard (Verifying if Display’s Processing Can Be Bypassed)  
HTPC – HDMI or DVI and Optical/Coaxial audio  
When the checkerboard test pattern is displayed correctly, close up you should be able to see a ꢀ-  
pixel checkerboard and at proper viewing distance the image should appear as an even gray. If the  
display is CrT-based you will not see this checkerboard, but the screen should be an even gray. When  
this test pattern is displayed incorrectly, the resulting image does not look like a fine checkerboard  
and may have irregular patterns. When this is the case, the chosen output resolution may not be the  
native resolution of the display or the display may scale all input signals even if the input resolution  
is already at native resolution. Check to make sure that the output resolution selected on the iscan  
STEP 5 - Configuring the Input sources to get the maximum performance  
s-Video and Composite connections do not need to be setup the correct output resolution because  
they only support standard definition resolutions, 480i or 576i. HDMI, DVI and Component outputs  
need to be properly setup on each source to get the best performance. You can verify the resolution  
that the iscan is receiving from the source by pushing the Info button.  
ꢀꢀ  
ꢀ2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Set Top Boxes  
DirecTV HR10-250 (HD-TiVo)  
HD-DVD Player – Configure the BD player to output 1080p-24 (if the player allows), if not use  
ꢀ080i-60 and the ‘forced 3:2’ mode. See Step 6  
Blu-Ray Player – Configure the BD player to output 1080p-24 (if the player allows), if not use  
ꢀ080i-60 and the ‘forced 3:2’ mode. See Step 6  
The Hd-TiVo does not allow the user to select one output setting that will always output the  
right resolutions under the right conditions. For example, when tuned to an SD channel the  
output resolution should be 480i, but when tuned to an Hd channel the resolution should be 720p  
(FOX, ABC, ESPN) or 1080i (all other HD channels). There is no, to very limited, 480p content.  
The Hd-TiVo can be set up to output only 480i, 720p and ꢀ080i when the user presses the  
Up button on the TiVo remote control.  
Game Consoles  
Xbox – Configure the Xbox to output all resolutions (480i, 480p, 720p and 1080i).  
Xbox360/360Elite – Configure the Xbox360 to output 720p.  
DirecTV Central  
Messages & Settings  
Settings  
Video  
PS2 – Configure the PS2 to output 480i only and use Game Mode 1 or 2. See Step 6  
_ _ _ _  
Output Format – Up Arrow Setup  
PS3 – Configure the PS3 to output all resolutions. Use Game Mode 1 or 2 for 1080i. See Step 6  
Wii – Configure the Wii to output 480p  
SA8300HD Cable HD-DVR  
ꢀ.  
With the dVr powered off, press the Guide and Info buttons at the same time.  
Other Digital Media Devices  
The HDTV Setup Wizard screen appears.  
Apple TV – Configure the Apple TV to output 480p  
2.  
3.  
4.  
Select the Advanced Setup option (press B)  
HTPC – Depending on the capabilities of the video card, configure the HTPC to output 720p  
Make sure that Display Aspect Ratio is set correctly (more than likely, 16:9)  
or 1080p. The higher the output resolution for the PC, the better text will look on screen.  
follow the on-screen instructions to select compatible picture formats.  
select 480i, 720p, and ꢀ080i  
5.  
6.  
7.  
8.  
9.  
after saving the picture formats, press EXIT.  
STEP 6 – Deinterlacing Mode and PReP™  
press POWER to turn on box.  
The iscan has a very high performance ‘autodeinterlacing mode which can handle most content.  
There are specific modes which are optimal for Gaming and HD-DVD/Blu-Ray players that do require  
initial setup. once these settings are made, they are saved into non-volatile memory. each input  
has a separate memory for each of the accepted input resolutions. For example, the HDMI inputs  
accept all of these resolutions:  
press Settings twice. The General Settings menu appears.  
press Move Up or Move Down to highlight Set: Picture Format.  
press Move Right to highlight the picture format setting.  
ꢀ0. press Move Up to select Pass-Through for Component video connection,  
and AutoDVI/HDMI for HdMi/dVi Connections.  
480i, 480p, 576i, 576p, 720p, ꢀ080i, ꢀ080p-24, ꢀ080p-60, VGa, sVGa, XGa, sXGa  
ꢀꢀ. press Accept A to use this option for the 8300Hd. The dVr front panel displays  
AUTO, plus the scan rate you are viewing (for example, 1080i).  
A source like an HD-TiVo can output 4 resolutions over HDMI (480i, 480p, 720p and 1080i). Although  
there are ꢀ2 memories on the HdMi inputs, only 4 would be used by the Hd-TiVo and they would  
automatically recalled when any one these 4 input resolutions is detected on that HdMi input.  
ꢀ2. press Exit.  
DCT6412 Cable HD-DVR –  
ꢀ.  
2.  
Make sure system is turned on.  
Game Mode 1 and Game Mode 2  
put the sTb in standby by pushing the Standby button on the Comcast remote or  
by simply hitting the Power button on the front panel of the cable box.  
use these modes to get high performance low latency deinterlacing. Game Mode ꢀ has less than  
motion-adaptive processing with less than 1 frame (17milliseconds) of delay and Game Mode 2 has  
less than 2 frames of delay with additional edge-adaptive processing for a slightly smoother picture.  
These modes are recommended for any connected game console that is outputting a 480i or ꢀ080i  
signal.  
3.  
4.  
push the Menu button to enter the “user settings” menu  
ensure that:  
— “TV Typeis set to ꢀ6:9  
— “YPbPr Output” to “1080i”  
— “4:3 override” to “480i”  
Input Adjust  
Deinterlacing  
_ _  
Game Mode 1 and Game Mode 2  
PReP  
Many DVD players and set top boxes do not output a 480i signal, using an HDMI/DVI or component  
connection. anchor bay’s progressive reprocessing can reprocess this signal and still improve the  
previously poorly deinterlaced signal. for these sources it is recommended that you set prep to  
‘on.  
Optical Disc and Other Prerecorded Media Sources  
DVD Player/Recorder – Configure the DVD player to output 480i on the HDMI, DVI, or  
Component connection. HdMi is the recommended connection if available. if the dVd  
player can not be configured to output 480i over one of these connections, configure  
it to output 480p and insure that you have turned prep ‘onfor this input. See Step 6  
Input Adjust  
PReP  
_ _  
On  
ꢀ3  
ꢀ4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Forced 3:2 Mode  
One is 4 IRE below black (blacker-than-black), one is 1 IRE above black, and the third is 2 IRE above  
black. Embedded in the white blocks are 3 bars. One is 1 IRE above white (whiter-then-white), one  
is ꢀ ire below white, and the third is 2 ire below white. The bottom two blocks differ slightly from  
these levels. for the bottom two blocks, the blacker-than-black is at the lowest possible luma level  
and the whiter-than-white bar is at the highest possible luma level. When the brightness and contrast  
are adjusted correctly, you should be able to see the ꢀ ire and 2 ire above black bars on the black  
background and the ꢀ ire and 2 ire below white bars should be visible on the white background.  
When the brightness is adjusted correctly, black objects should appear black’ with the details still  
intact and lighter areas should be light, not gray, with the details still intact. When the contrast is  
adjusted correctly, white objects will appear ‘white’ with the details still intact. because the contrast  
settings can affect brightness settings we recommend that you check the brightness setting after  
making this adjustment.  
This mode is perfect for Hd-dVd and blu-ray players that output a cleanly encoded 3:2 signal over  
the entire length of a movie. This insures the highest performance playback from these high quality  
sources. If you intend on setting up the iScan to output a 24Hz, 48Hz, or 72Hz signal for film-based  
content this mode is highly recommended.  
Input Adjust  
Deinterlacing  
Forced 3:2  
_ _  
STEP 7 – Assigning Audio Inputs to Video Inputs  
The iScan features an audio delay function to exactly match the video delay incurred by the video  
processing. The iScan accepts four discrete digital audio inputs, two optical (Audio 1, 2) and two  
coaxial (Audio 3 and 4) inputs, one analog audio input and four HDMI audio inputs (3 on the iScan  
Vp20). by default, no audio inputs are assigned to any video inputs. To assign an audio an input to  
a video input, first select the video input using the remote control or front panel controls and then  
select the audio input.  
NOTE: if you have a CrT based display, following the instructions above may yield a contrast setting  
too high. if the contrast is set too high, you will get blooming and loss of details in the highlighted  
areas. it is more helpful to use the two vertical lines in the test pattern. adjust the contrast up and  
down and you will notice that these lines will bend as you increase the contrast. To properly adjust  
contrast on a CrT based display, decrease the contrast until the vertical lines start to straighten out.  
if possible, the two lines should be straight. on some CrT, the lines may not straighten even if you  
turn the contrast to its minimum. if this is the case, slowly increase the contrast to a point just before  
the vertical lines have extreme bending. You have now properly set up the contrast of the display.  
Input Adjust  
Audio Input  
(Make Selection)  
_ _  
Continue to set up brightness as detailed above.  
NOTE: if an analog video input is selected, the HdMi option will not be available. an audio input can be  
assigned to multiple video inputs, but a video input can not have multiple audio inputs assigned to it.  
Color Bars 75 and Color Bars 100  
NOTE: There are some HdMi sources that do not output the correct audio signal when connected to  
an HdMi repeater, like an aV receiver or video processor. in these instances, we recommend that use  
an alternative method of sending audio, like the optical or coaxial digital audio outputs.  
The ‘Color8 Bars75’ and ‘Color8 Bars100’ will assist in setting up the saturation (color) and hue (tint)  
of the display. The ‘Color8 bars75’ test pattern consists of 8 vertical bars across the screen at a 75%  
saturation level. The ‘Color8 barsꢀ00’ test pattern consists of 8 vertical bars across the screen at  
a ꢀ00% saturation level. from left to right the bars are: white, yellow, cyan, green, magenta, red,  
blue, and black. To properly adjust the saturation and hue you will need to use the blue colored filter  
that comes with AVIA. You will also need to turn off any automatic flesh tone controls on the display  
before making these adjustments. When the saturation and Hue are adjusted correctly, the white  
bar and the blue bar should be exactly the same shade when looking through the blue filter.  
saturation and hue settings interact with each other so after making this setting you may want to go  
back and check that the saturation setting is correct.  
insure that the audio output from the iscan is connected to the aV receiver/processor. note that both  
the optical and coaxial outputs are active simultaneously. Also note that multi-channel PCM audio,  
like that encoded on HD-DVD and Blu-Ray must be transmitted by HDMI, as optical and coaxial are  
incapable of carrying these formats. Make sure that Hd-dVd or blu-ray player is outputting bitstream  
only if the aV receiver does not have an HdMi audio input. if the aV receiver does have an HdMi in-  
put, connect the HdMi output from the iscan to the aV receiver and the output from the aV receiver  
to the display. If there is no picture displayed, revert to using optical or coaxial digital audio. Some  
AV receivers are incapable of passing high resolution video signals (1080p).  
STEP 9 – Source Optimization – iScan Adjustments  
To get the best performance out of each of the sources you should individually calibrate each input  
specifically to the connected source. In this section, all picture control adjustments are made using  
the iscans picture controls. Keep in mind that if you replace a source with a new component you  
will also want to recalibrate the input. To calibrate each source correctly you will need the source  
to output a reference test pattern similar to what is built in to the iscan. for sources like dVd, ld  
and d-VHs, this content is readily available. but for a source like Hd satellite or cable, these test  
patterns are played on channels like Hdnet at off hours. so if you have a dVr, anchor bay recommends  
that you record these test patterns.  
STEP 8 – Display Optimization – Using Display Adjustments  
The iscan Vp50pro has several test patterns to assist in the setup of the display. adjustments should  
be made on the display, not on the iscan, to correctly setup the iscan and display.  
Gray Ramp  
The ‘Gray ramp’ can help verify that the display is showing the gradients between black and white  
correctly. You should see a smooth transition between black and white with this test pattern. If there  
is banding on the extreme right and left of this test pattern with ‘Video’ Output Levels, change the  
‘output levels’ to ‘pC.  
VRS Optimization & Evaluation DVD  
This dVd will assist in setting up the input to which the dVd player is connected. anchor bay  
recommends that you use a digital connection, dVi or HdMi, or a high quality analog connection, like  
component video. don’t use s-Video or Composite video for a higher quality source like dVd. before  
calibrating the input for the dVd player, make sure that the dVd player is set to ‘ꢀ6:9’ output, not  
‘4:3. You will also want to turn off any extraneous features like noise reduction which may add more  
noise than help. set all picture settings on the dVd player to either ‘off, default, or ‘0.  
Brightness/Contrast  
The ‘Brightness/Contrast’ test pattern will assist you in setting up both the brightness (black level)  
and contrast (white level) of the display. The ‘Brightness/Contrast’ test pattern is composed of 4  
quarter-screen blocks. Two of the blocks have a background level of standard black and the other  
two blocks have a background level of standard white. embedded in the black blocks are 3 bars.  
ꢀ5  
ꢀ6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The iscan has several ‘Half Test patterns’ that can be brought up while the matching test patterns are  
played from the Vrs dVd. The test patterns to use on the dVd are listed below. The matching test  
patterns can be found in the ‘Configuration’ menu (Configuration Test patterns).  
seCTion 4 – Menu opTions  
Input Select  
Static Patterns  
Half Patterns  
Black and White  
Color (7) Bars 75  
Color (7) Bars 100  
Color (8) Bars 75  
Color (8) Bars 100  
_ _  
There are eleven video inputs on the iscan Vp50pro  
:
VIDEO 1 - Video 1 (Composite)  
VIDEO 2 - Video 2 (Composite)  
s -Video ꢀ - s -Video ꢀ  
s -Video 2 - s -Video 2  
CoMponenT ꢀ - Component/rGbs ꢀ  
CoMponenT 2 - Component/rGbs 2  
rGbHV – rGbHV/Component  
HdMi ꢀ - HdMi ꢀ  
Adjusting for Overscan per Input  
overscan can be adjusted individually on each input. overscan tends to be most problematic with  
standard definition broadcast signals from terrestrial, cable or satellite. Overscan can also be needed  
with game consoles. Check each output resolution from the source and adjust the overscan,  
as needed.  
HdMi 2 - HdMi 2  
HdMi 3 - HdMi 3  
Setting Up and Recalling Display Profiles  
HdMi 4 – HdMi 4  
Up to 10 Display Profiles can be defined and recalled. A Display Profile is a memory which holds all  
of the parameters that are defined in the ‘Output Setup’ menu. Display Profiles can be used to drive  
two different displays, like a plasma for day usage and a front projector for night usage that need  
different output settings, or to drive a single display with different settings, one setting optimized  
for NTSC and one optimized for PAL. To use the Display Profiles, first set up all Output Settings  
and then save the Display Profile.  
auTo - automatic active input detection and selection  
These inputs can be accessed in five different ways:  
using the front panel using the pand qbuttons  
using the remote control with the direct access buttons  
using a universal remote programmed with the discrete codes  
using the osd from the front panel or from the remote to access the input select menu  
Using RS232 Serial Automation Protocol described in the appendix.  
Output Setup  
Display Profiles  
Save  
_ _  
Once a Display Profile is saved, it can be recalled using the Display Profile button on the remote  
control, or by navigating the osd.  
Input Aspect Ratio Control  
Output Setup  
Display Profiles  
_ _  
Select  
The input aspect ratio control selects the aspect ratio for the current input signal. The iscan Vp50pro  
automatically converts from the selected input aspect ratio to the selected output aspect ratio.  
Setting up the iScan for a 2.35:1 Constant Image Height Configuration  
The input aspect ratio control selects the aspect ratio for the current input signal. The iscan Vp50pro  
automatically converts from the selected input aspect ratio to the selected output aspect ratio.  
The iscan Vp50pro can be configured to work in conjunction with an anamorphic lens. The most  
common configuration with one of these lenses is a 2.35:1 screen with a 16:9 projector. This  
lens can be fixed or motorized. If the lens is motorized, it should only be used when viewing  
push the Aspect button once to show the current input aspect ratio control function. To cycle through  
the available functions, push the Aspect button repeatedly.  
2.35:1 content. The motorized lens should be connected Trigger #2 on the back of the VP50pro  
.
ThecorrectoutputaspectratiosettingforthisconfigurationisLensoptionMode1–Autoandthecorrect  
for the input ar function, push the por button once to show the current setting. push either of  
these buttons again to cycle through the available aspect ratios. push the Exit button to exit the  
menu and go back to the input aspect ratio selection.  
‘ꢀ2V Trigger 2’ setting is ‘lens.  
Advanced Control — Setting up the iScan to Output 24Hz/48Hz  
(For Film-Based Content)  
for the Zoom, pan and borders functions, push the por button to select the two control settings  
available: horizontal and vertical. Push the Enter button to adjust each setting.  
Some displays, mostly front projectors, can display a 24, 48 or 72Hz signal (which is a multiple of  
film’s 24 frames per second). To verify if the connected display can accept one of these framerates  
use the ‘Judder’ test pattern. This pattern displays a bar that bounces back and forth at the chosen  
output frequency selected in the framerateparameter. When this test pattern is displayed correctly,  
the bar moves smoothly across the screen and bounces from side to side. When this pattern is  
displayed incorrectly, this bar may ‘tearas it moves across the screen. if your display does accept  
24Hz or 48Hz a ‘Display Profile’ should be saved for viewing film-based content in addition to a  
standard 50/60Hz video ‘Display Profile.  
push pand q to increase or decrease the setting.  
Push Exit again to exit this mode.  
NOTE: The Zoom and pan functions are applied to the input signal, not the output. This is an im-  
portant consideration, especially for the Pan function. For example: If you do not zoom a full frame  
image more than ꢀ00%, there is nothing to pan. However, if part of the image is not on the screen,  
then the pan function will work.  
ꢀ7  
ꢀ8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
page 25  
page 25  
The Vp50pro‘s menu is exit automatically after 30 seconds of no user interaction.  
When the aar is less than the oar, the iscan Vp50pro puts up borders on the left and right as  
shown below:  
Video input signals are usually classified in the following two ways:  
frame aspect ratio  
active input aspect ratio  
Active Input  
Area  
Borders  
Frame Aspect Ratio  
Frame Aspect Ratio (FAR) consists of two possible ratios: 4:3 or 16:9. DVD discs encoded in a 16:9  
frame are sometimes referred to as anamorphic or enhanced for widescreen TV’s. For example, a  
non-anamorphic widescreen dVd has a far of 4:3.  
When the AAR is equal to the OAR (Output Aspect Ratio), the iScan VP50pro supplies no border  
as shown below:  
Active Aspect Ratio  
Active Aspect Ratio (AAR) is the aspect ratio of the image or content (movie). This content is typically  
stated on the back cover of dVd discs. some common active aspect ratios are as follows:  
Active Input  
Area  
1.33:1 (4:3)  
ꢀ.55:ꢀ  
ꢀ.66:ꢀ  
1.78:1 (16:9)  
ꢀ.85:ꢀ  
Zoom  
2.35:ꢀ  
The Zoom function zooms in on or magnifies the image on your display. The minimum zoom is 100%,  
(no zooming); the maximum zoom is 150% (zoom magnification factor of 1.5X). Zoom controls can  
be accessed by using the osd or by using the direct access button on the remote control. on the  
remote control, push the Zoom button followed by the p/ buttons to vertically zoom the image or  
the Left/Right buttons to horizontally zoom the image. The amount of horizontal and vertical adjust-  
ment will be displayed on the front panel display.  
To use aspect ratios in addition to these, the iscan Vp50pro provides the option to choose a custom  
aspect ratio called ‘user’ with a range of ꢀ.0ꢀ:ꢀ-3.00:ꢀ.  
Panorama  
Using the OSD, select the control that you would like to adjust, Horizontal or Vertical zoom, and push  
the Enter button to show the current Zoom setting. push the pand button to increase or decrease  
the zooming factor. Zoom can only increase the size of the image.  
The panorama function displays a 4:3 image in a non-linear stretch mode on a ꢀ6:9 display. This  
can be useful for extended viewing of this content on a display susceptible to bun-in, like a plasma  
or CrT.  
NOTE: The Zoom and pan functions are applied to the input signal, not the output. This is an im-  
portant consideration, especially for the Pan function. For example: If you do not zoom a full frame  
image more than ꢀ00%, there is nothing to pan. However, if part of the image is not on the screen,  
then the pan function will work.  
iScan Image Mapping  
The situation when the Frame Aspect Ratio (FAR) is the same as the Active Aspect Ratio (AAR) is  
sometimes called full frame. This situation is illustrated below.  
Pan  
The iscan Vp50pro maps the AAR to the Output Aspect Ratio (OAR) in the following three ways:  
The pan function allows the image to be shifted up, down, left and right. note that the pan function  
can only be used after the image has been zoomed to any value greater than 100%. Pan controls  
can be accessed by using the osd or by using the direct access button on the remote control. on the  
remote control, push the pan button followed by the p/ buttons to vertically pan the image or the  
t/ ubuttons to horizontally pan the image. The amount of horizontal  
When the aar is greater than oar, the iscan Vp50pro puts up borders at the top and bottom  
as shown below:  
page 25  
and vertical adjustment will be displayed on the front panel display. using the osd, select the control  
that you would like to adjust, Horizontal or Vertical pan, and push the Enter button to show the cur-  
rent pan setting. push the p and button to increase or decrease the panning factor.  
Active Input  
Borders  
Area  
Borders  
The Borders function allows you to add horizontal and/or vertical borders around the image. These  
borders obscure part of the input image. Certain input-to-output aspect ratios already result in left/  
right or top/bottom border being added. This control allows the system-generated borders to be  
extended, or for borders to be added when none exist. As the borders are adjusted (see below) the  
iscan temporarily increases the gray level of the borders so that they are visible during the adjust-  
ment process. The level will return to normal after the adjustment has ceased.  
ꢀ9  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Save User-defined presets as follows:  
Horizontal Border Control: push the p button to move the left and right borders towards  
the middle of the image, increasing the border width and cutting off the sides of the input  
image. push the button to move the left and right borders away from the image and decreases  
their width. If there are system-generated left/right borders already present (for example,  
when the input aspect ratio is 4:3 and the output aspect ratio is ꢀ6:9), the border width cannot be  
decreased beyond the base width created by the aspect ratio conversion.  
Customize the aspect ratio manually (refer to Setting the Input Aspect Ratio Manually above).  
Select one of the presets from the ‘Save User To’ menu. Confirm the action by selecting Yes.  
There are 10 user-definable presets available.  
NOTE: Be careful, because saving to a preset deletes the previous preset. If you have not customized the  
aspect ratio, and the current aspect ratio settings are the same as a system defined preset. In this case,  
the system will not allow you to save the preset setting.  
Vertical Border Control: push the p button to move the top and bottom borders towards the  
middle of the image, increasing the border height and cutting off the sides of the input image.  
push the button to move the top and bottom borders away from the image and decrease their  
height. If there are system-generated top/bottom borders already present (for example, when the  
input aspect ratio is ꢀ6:9 and the output aspect ratio is 4:3), the border height cannot be decreased  
beyond the base height created by the aspect ratio conversion. borders are automatically added  
by the system when the active input aspect ratio is not the same as the output aspect ratio as  
explained earlier in this guide. However you can add more borders using the Borders menu.  
Input Adjust Control  
Push the Input Adjust button once to show the current input adjustment function. You can cycle  
through the available functions by pushing this button repeatedly.  
Mosquito Noise Reduction  
The iscan Vp50pro has Mosquito noise reduction to reduce random noise that appears along the  
edges of compressed images. There are four settings to this control: off, low, Medium, and High.  
The default setting for this control is ‘off. This is a setting that is saved on a per input/per format”  
basis.  
Presets  
You can specify the Input Aspect Ratio by using the Presets or Manually.  
Deinterlacing  
There are several deinterlacing modes available on the iscan Vp50pro. This is a setting that is saved  
on a per input/per format” basis. The functions of these modes are described below:  
Using Presets  
You can use Presets with either the OSD or the Remote Control Input Aspect Ratio button.  
refer to the preset sub-menu in the input ar menu for doing this with the osd. The remote control  
operation is described below.  
Auto – This mode is the default. ‘autorepresents the best balance between automatic  
detection of film and video sources, bad edit detection, and identification of mixed-mode  
sources. This mode should be used when the content may be a mix of film and video  
content or you are not sure.  
4:3  
selects 4:3 full frame without osd.  
selects ꢀ6:9 full frame without osd.  
16:9  
Film Bias Mode – This mode is intended for use on content that is known to be film-based.  
Video Mode – This mode is intended for use on content that is known to be video-based.  
pushing the Input Aspect Ratio button repeatedly toggles between 4:3 Full Frame, Letterbox, 16:9  
Full Frame, 4:3 Stretch, and Preset 1 through Preset 10 and User. You can also navigate through  
these presets using the pand qbuttons, along with Enter to confirm the selection.  
Forced 3:2 – This mode is intended to be used with ‘high-quality’ film sources like  
HD-DVD and Blu-Ray. This forced cadence mode is definitely useful for watching a movie  
from start to finish but they are less useful for content with a lot of bad edits, and also  
if youre going to be skipping around a lot between chapters.  
The ten user-defined preset value selections (Preset 1 - 10) are stored in non-volatile memory and  
are always available.  
each of these presets consists of the following:  
Forced 2:2 – This mode is intended to be used with ‘high-quality’ film sources like  
HD-DVD and Blu-Ray. This forced cadence mode is definitely useful for watching a movie  
from start to finish but they are less useful for content with a lot of bad edits, and also if  
youre going to be skipping around a lot between chapters.  
frame aspect ratio  
active input aspect ratio  
Zoom parameter  
pan parameter  
2:2 Even – This mode should be used when the user knows that the source is high-quality  
2:2 pulldown (i.e. film-based content played back in a country with a 50Hz video standard)  
and wants to avoid any loss of cadence lock while watching that source. This mode weaves  
two adjacent fields together starting with an even field and combining it with the following  
odd field. This will provide a higher quality overall signal than the ‘Auto’ or ‘Film Mode’  
settings, providing that the source really is 2:2 pulldown and does not have bad edits.  
only one of the ‘2:2’ deinterlacing settings is correct for any given source and the correct  
mode can be chosen by simply trying both of them and selecting the one which does  
not result in combing artifacts.  
borders  
The user preset selection is also stored in non-volatile memory. However the user selection is always  
updated after you modify any pre-defined aspect ratio setting. In order to permanently keep a custom  
aspect ratio setting, you must save it to one of the four preset selections.  
Setting the Input Aspect Ratio Manually  
You can set the following parameters manually:  
2:2 Odd – This mode is very similar to ‘2:2 Even’ except that that this weaves two  
adjacent fields together starting with an odd field and combining it with the following  
even field.  
frame aspect ratio  
active input aspect ratio  
Zoom parameter  
pan parameter  
Game 1 – This mode is intended for use with game consoles (like those from Sony,  
Microsoft and nintendo). This mode gives you minimal latency with edge-adaptive  
processing. The total amount of delay with source-locked output mode set on the  
Vp50pro is about half a frame of delay. unlocked frame rates will increase this delay.  
borders  
2ꢀ  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Game 2 – This mode is intended for use with game consoles (like those from Sony,  
Microsoft and nintendo). This mode gives you minimal latency with both motion and  
edge-adaptive processing. The total amount of delay with source-locked output mode  
set on the Vp50pro is about one and a half frames of delay. unlocked frame rates will  
increase this delay.  
for the bnC inputs the options are:  
RGB(H+V)  
YPbPr  
Input Level  
The input level setting allows the user to specify the levels of the input signal, either Video (16-235)  
or PC (0-255). This control only works with an input signal that has RGB color space.  
PReP™, Progressive ReProcessing  
PReP is a video processing technology, which is exclusive to Anchor Bay that converts a progres-  
sive signal to its original interlaced format so that it can be subsequently deinterlaced by anchor  
bay’s precision deinterlacing. With prep, in addition to performing an outstanding job deinterlacing  
interlaced formats, an iscan Vp50pro can now improve a previously poorly deinterlaced progressive  
format. prep works with 480p, 576p, ꢀ080p/50 and ꢀ080p/60. Turning prep ‘onand ‘offallows the  
Video  
pC  
VCR Mode  
VCr Mode decouples the output timing completely from the input timing to ensure a stable output  
from the iscan Vp50pro for VCR playback especially during trick-play modes (play forward, play  
reverse, still/pause). This mode is available on the composite and s-Video inputs.  
user to compare the deinterlacing done by the source versus the deinterlacing done by the Vp50pro  
.
The default for this setting is ‘off. This is a setting that is saved on a per input/per format” basis.  
On – output timing is decoupled from the input timing regardless of frame rate settings.  
Off – output timing is dependent on frame rate settings.  
Passthrough  
The iscan Vp50pro can pass signals through as well as process them. With some signals, like those  
coming from a pC, no processing may be desired in which case this setting can be set to ‘on’ to allow  
this signal to pass through the Vp50pro. note that if an analog signal is passed through the Vp50pro  
there will be no video output on the HdMi output, and vice versa. This mode can also be used to see  
the signal processed by the Vp50pro versus the processing done by the display. The default for this  
setting is ‘off. This is a setting that is saved on a per input/per format” basis.  
Auto - Turns on VCr Mode if a VCr source is detected. This is the default setting.  
HDMI Config.  
HDCP Mode  
There are two HdCp modes:  
Overscan  
Off: HdCp is disabled at the iscan Vp50pros HdMi input. some sources turn off HdCp  
in this case and the iscan Vp50pro drives a non-HdCp dVi display or an analog display.  
The Overscan function scales the input image proportionally in both vertical and horizontal dimen-  
sions by the user-specified overscan factor. The purpose of Overscan is to remove unwanted image  
portions around the perimeter of the image. The default overscan value is 0, which means ꢀ00%  
of the input image is shown. The maximum overscan value is 20 which means the input image is  
scaled up by ꢀ20%. This is a setting that is saved on a per input/per format” basis.  
On: The iscan Vp50pro continuously looks for a HdCp source on its HdMi input.  
This is the default setting.  
NOTE: The iscan Vp50pro is not designed to remove HdCp from a protected signal. if this setting is set  
to ‘on’ make sure that the corresponding HdCp Mode setting on the output is also set to ‘on’  
To adjust the overscan level:  
ꢀ. push the por qbutton. The current level is shown.  
Auto AR  
2. push the por qbutton to decrease or increase the amount of overscan.  
3. The overscan value is applied to all input aspect ratios and is independent of the Zoom value.  
In addition to carrying audio and video, HDMI can carry other information, like aspect ratio (AR).  
if you would like the iscan Vp50pro to automatically set the ar based on the information on the  
HdMi signal, than set this setting to ‘on.This ar information can be wrong or implemented  
incorrectly, so this setting is defaulted to ‘off.  
Image Shift  
The Image Shift adjustment allows the user to vertically and horizontally adjust the image, when  
the input signal is 480i/576i on the sdi or HdMi inputs or a pC resolution on the analog bnC input.  
This function can be set independently for different input formats. The default setting for the horizon-  
tal and vertical shifts is midrange, 0.  
Auto Color Space  
in addition to carrying audio and video, HdMi can carry other information, like color space. if you  
would like the iscan Vp50pro to automatically set the ar based on the information on the HdMi signal,  
than set this setting to ‘on, which is the default. if this setting is set to on, the ‘Colorspaceadjust-  
ment will be unavailable.  
Color Space  
The color space setting allows the user to specify what the input signal is on the HdMi inputs.  
Auto Input Priority Selection  
rGb  
The auto input priority selection function assigns different priorities to the video input’s automatic  
active video selection mode (AUTO in Input Select menu). First select the video input then change  
the priority of that input.  
YCbCr 4:2:2  
YCbCr 4:4:4  
auto  
ꢀ - press the qbutton. The first video input VIDEO 1 is shown.  
2 - press the Enter button to view the current priority of the selected input.  
3 - press the por qbutton to change the priority of the selected input.  
23  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4 - press the Exit button again to complete the priority assignment.  
Saturation  
The iscan Vp50pro allows you to control the saturation of the image independent of the display.  
saturation is the same as the “Color” control on most TVs and controls the richness of the color in  
the image. The default setting is midrange, 0.  
5 - Repeat Steps 1 through 4 to select the next video input and adjust the priority setting.  
Audio Input  
Hue  
The audio input function assigns an audio input to the currently selected video input. four digital  
audio inputs and a single analog audio input are available. The HdMi inputs can accept both audio  
and video. To assign the audio input to another video input, push the p/qbuttons. The front panel  
display (FPD) shows the current setting. For more info about how to assign an audio input to a video  
input, refer to Audio Input Operation.  
as with saturation, hue can also be controlled independent of the display. Hue is the same as the  
“Tint” control found on most TVs and controls how colors are displayed in the image. The Hue control  
is not available for Component or pal/seCaM inputs. The default setting is midrange, 0.  
Y/C Delay  
Sometimes there is a lag between the Luminance (Y) and the Chrominance (Pb/Pr or Cb/Cr) of the  
video signal. This causes a color smearing” because the color component of the image is not lin-  
ing up properly to the black and white luminance component of the image. The iscan Vp50pro can  
compensate for these errors in the source signal by shifting the phase of the Y with respect to the  
C, forward or backward to align them properly. use the pand qbuttons to adjust the phase and  
observe the effects on your display to obtain the optimal setting. The default setting is 0.  
AV Lip Sync™  
The iscan Vp50pro automatically delays the input audio to match the video processing delay.  
You can choose to increase or decrease the audio delay by changing this setting. Push the por  
qbutton to display the current additional bias delay setting (default 0). Up to 200 milliseconds  
of delay can always be added to the audio signal after the iscan has compensated for the video  
delay. use the por qbutton to increase or decrease the delay in milliseconds.  
Chroma Filter (Auto CUE-C™)  
This feature removes chroma upsampling errors (CUE) found in video sources which have been MPEG  
NOTE: The total audio delay cannot be less than 0, that is, the iscan cannot have negative audio  
delay. if you choose to decrease the automatic delay setting by a certain amount, this value could  
be changed by the iScan in situations where the iScan’s calculated delay plus the specified additional  
delay results in a value less than 0.  
encoded and then improperly decoded.  
Off - No chroma filtering. Use this setting if the source does not have a CUE problem.  
On - Chroma filtering is always on. Use this setting if the source is known to have a CUE problem.  
Picture Controls  
Auto - automatic chroma error detection and correction. use this setting when you don’t  
know if a source has a Cue problem. also use this setting for all digital sources which use  
MPEG2 decoders (DVD players, digital satellite receivers, and so on.) as it will also detect and  
correct chroma errors created by all sources of this type when the source is encoded as inter-  
laced (also sometimes called Interlaced Chroma Problem, or ICP). This is the default setting.  
for each input there are different picture memories for each accepted input resolution. These memo-  
ries are accessed automatically when an input resolution is detected.  
Fine Detail Enhancement  
Presets  
This control enhances the fine detail in images. Fine detail can be sharpened by adjusting the control  
into the positive range, up to 50, and it can be softened by adjusting this control into the negative  
range, down to -50. The default setting on this control is midrange, 0.  
The iscan Vp50pro has 5 memories that can be used to set the picture Controls differently on the  
same input. 3 of these presets are “ISF” modes that can only be saved by an ISF Certified Calibrator  
experience during the day and night, where the ambient light is typically different. There are also  
2 modes which can be used by a User to define their own optimum viewing during these same  
conditions. To adjust these parameters, simply highlight the preset that you would like to change  
and then make changes.  
Edge Enhancement  
This control enhances the sharpness of images on the edges. edges can be sharpened by adjusting  
the control into the positive range, up to 50, and they can be softened by adjusting this control into  
the negative range, down to -50. The default setting on this control is midrange, 0.  
Brightness  
Configuration  
This control adjusts the brightness (black level) of the overall image output from the iScan VP50pro  
.
if you turn it up too high, it may make black look gray. in general, you should adjust this up until  
you see the black areas of your display turn gray and then back it down just below that point. The  
default setting is midrange, 0.  
Test Patterns  
The iscan Vp50pro has 27 internal test patterns to assist in the setup of your individual sources and  
your display. To learn more about how to use the internal test patterns, refer to Section - 3: Setup.  
To turn the test patterns on and off, use the Test Pattern On/Off button. To navigate backwards and  
forwards through the available test patterns use the tand ubuttons, respectively.  
Contrast  
Contrast adjusts the ratio between white and black signal levels and is effective as a gain control.  
The difference between this and the brightness control is that this adjusts the difference between the  
brightest and darkest part of the image. Note that all displays have a maximum white level. Going  
beyond this level only “clips” the upper gray levels and you will lose color resolution at the brighter  
levels. adjust this control up until you see the brighter levels of the image begin to wash out, at this  
point, back it down just below that point. The default setting is midrange, 0.  
Auto Standby  
The default setting is ‘off, which means iscan Vp50pro is always in active mode, regardless of the  
activity state of the selected input. if auto standby is ‘on, the iscan Vp50pro goes into standby mode  
30 seconds after the selected input becomes inactive. To see the current setting, press por q.  
Then press the same button again to change the setting.  
25  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
This screen is helpful during troubleshooting.  
LED Brightness  
This selection allows the user to configure the behavior of the Front Panel LED brightness. The  
‘normalparameter adjusts the brightness of the front panel led when the menu is being navigated.  
The ‘navigateparameter adjusts the brightness of the front panel led during normal usage, when  
the menu is not being navigated.  
User Mode  
You have limited access to the output timing controls in ‘Normal’ mode. In ‘Advanced’  
user mode, you have access to the complete set of output timing controls. push the  
qbutton to see the current setting and the fpd displays either ‘normalor ‘advanceduser level.  
push the qbutton again to select the alternate mode. The default setting is ‘normal.  
Serial Port Rate  
The serial port is used by the automation system controllers to control the iscan Vp50pro . The serial  
port baud rate defaults to ꢀ9200 bps, but can be changed using the por qbutton.  
Output Setup  
The supported baud rates are:  
Analog/Digital Output  
The iscan Vp50pro can output either an analog or digital video signal. The default setting is for the  
digital, HdMi, output to be active. To output to a display with an analog input, insure that this setting  
is set to ‘Analog (BNC)’  
4800 bps (4.8K)  
9600 bps (9.6K)  
14400 bps (14.4K)  
19200 bps (19.2K)  
38400 bps (38.4K)  
57600 bps (57.6K)  
Output Format  
The current selected output format will be highlighted in the osd in red. To select a different out-  
put format, highlight it first and then press the ubutton. adjustment of advanced timing controls  
can also be made here although most displays do not need ‘custom’ timing. The user Mode, in the  
Configuration menu, must be changed to ‘Advanced’ for the advanced timing controls to be acces-  
sible. for a complete list of the available output presets, see the Complete Menu Tree in section 5.  
Factory Default  
The factory default option allows you to reset all system settings to their factory defaults.  
ꢀ- press either the por qbutton. The fpd displays ‘no.  
2- Press the same button to switch to ‘Yes.  
Output Aspect Ratio Control  
3- Confirm this selection by pressing the Enter button.  
There are five controls for Output Aspect Ratio (OAR):  
NOTE: resetting the iscan Vp50pro to the factory defaults will cause all previously saved settings to  
be lost. record any important settings before performing this action.  
display aspect ratio  
lens Mode  
screen aspect ratio  
image shift  
Software Update  
use this parameter to install the latest software into your iscan Vp50pro. The latest software is  
available at www.anchorbaytech.com/update. The website includes complete download install  
instructions.  
underscan  
The Display Aspect Ratio is the full aspect ratio of the display, normally specified in the display manual.  
The most common display aspect ratios are 4:3 and ꢀ6:9. less common ones are 5:4, 2.35:ꢀ and  
others. The example below shows a 4:3 projector with a 16:9 screen.  
Page 37, R2  
12V Trigger Level  
The state on the ꢀ2V triggers can be changed so that the connected device is in the correct state  
when triggered by the iscan Vp50pro  
.
Information  
This setting shows information about the system including:  
Active Output  
Area  
3
9
Mask  
Video source  
signal Type  
audio source  
aspect ratio  
16  
4
Output Status  
In this example, the region outside the Active Output area (called the mask) is inactive, and only impor-  
tant for creating video timing signals for the display. input video data is never mapped to this region.  
resolution  
frame rate  
line rate  
aspect ratio  
27  
28  
Download from Www.Somanuals.com. All Manuals Search And Downloapd.age 38  
Screen Aspect Ratio  
(2.35:1)  
Screen Aspect Ratio  
(2.35:1)  
Mask  
Image  
Visible Area  
Active  
Output  
a video projector can also be used in conjunction with an anamorphic lens. an anamorphic lens allows  
the user to focus the maximum resolution and brightness into a specified area, either 16:9 or 2.35:1.  
The most common configuration is a constant image height (CIH) system with a 16:9 projector, an  
anamorphic lens and a 2.35:1 screen. In this configuration, the anamorphic lens can either be fixed or  
motorized. If the lens is fixed then the proper ‘Lens’ mode is ‘Mode 1’ when the content has a 2.35:1  
aspect ratio, or higher, and ‘Mode 2’ is for content that has an aspect ratio less than 2.35:ꢀ.  
Sync Type  
The Sync Type option sets the synchronization signal type of the output format. Press the por q  
button to show the current sync type. Press the same button again to move to the next sync type.  
Currently, the iscan supports seven sync types:  
Bi-level bi-level sync on green/luma  
Tri-level tri-level sync on green/luma  
Panamorph “Lens” modes defined:  
CSync Composite Sync (on the H sync BNC connector)  
H+V+ positive Hsync and positive Vsync  
H+V- positive Hsync and negative Vsync  
H-V+ negative Hsync and positive Vsync  
H-V- negative Hsync and negative Vsync  
Mode ꢀ: Content is displayed by the projector vertically stretched by 33%.  
Page 37, R2  
Mode 2: Content is horizontally squeezed by 25%. This mode is necessary for fixed-lens  
applications with ꢀ6:9 projector/2.35:ꢀ screen and 4:3 projector/ꢀ6:9 screen  
configurations.  
Active Output  
Page 37, R2  
3
9
Mask  
Area  
Color Space  
In a CIH system with a motorized lens, it should only be used when the input content has a 2.35:1,  
or higher, aspect ratio. The proper mode to use with a motorized anamorphic lens is ‘Mode 1 – Auto.  
The color space parameter sets the color space of the output format. press the Enter or ? button to  
show the current color space. press the same button again to select the alternate color space. Two  
analog color space options are supported: YPbPr (default) and RGB. Two digital color space options  
are supported: RGB (default) and YCbCr (both 4:2:2 and 4:4:4).  
16  
in this mode, the proper ‘lens’ mode is automatically selected based upon the selected active ar on  
the input. if the active ar is 2.35:ꢀ or above, “Mode ꢀ” is activated, if the active ar is below 2.35:ꢀ,  
Active Output  
“noneis selected. With this mode selected, the ‘display’ and ‘screenoptions will also be grayed  
3
9
Mask  
Area  
4
out. If the motorized anamorphic lens also has a 12V trigger, it can be automated by connecting to  
Output Level  
Trigger #2 on the back panel, and setting the ‘Output Setup  
Trigger 2’ setting to ‘lens.  
_
The output level setting allows the user to specify the levels of the output signal, either Video  
(16-235) or PC (0-255).  
16  
When the display aspect ratio is not the same as active output aspect ratio and the lens mode is set  
to ‘none, the mask is set to blanking levels and always centers the position of the active area over the  
display area. Image shift allows you to adjust the location of the image on your screen both horizon-  
Framerate Conversion  
This parameter enables frame rate conversion. There are four sets of controls, one for 24Hz input  
4
tally and vertically when the ‘Screen’ aspect ratio is not equal to the ‘Display’ aspect ratio. The example  
below shows 16:9 projector (1.78:1) and a 2.35:1 screen, you can shift the image to match the exact  
sources, one for 25Hz input sources, one for 50Hz input sources and one for 60Hz input sources.  
page 38  
location of your screen. in this situation, the image is shifted down putting all of the mask at the top  
of the projected image.  
For 24Hz sources, the output frame rate can be 24Hz, 48Hz or 60Hz, which allows the user to view  
24Hz content on a 60Hz display. For 24Hz sources the output can also be unlocked to 50Hz so that  
this content can also be viewed on a 50Hz display.  
page 38  
For 50Hz sources, the output frame rate can be either 50Hz or unlocked at 60Hz, which allows the  
user to view PAL/SECAM content on an NTSC display. For 60Hz sources, the output frame rate can  
be either 60Hz or unlocked at 50Hz, which allows the user to view NTSC content on a PAL/SECAM  
display.  
Screen Aspect Ratio  
(2.35:1)  
Screen Aspect Ratio  
(2.35:1)  
Mask  
First of all, note that there are separate settings for 60 Hz sources and 50 Hz sources. This allows  
you, for instance, to configure the iScan’s output to behave differently with NTSC and PAL sources.  
one potential advantage of this is that if you have a display which only works at a single frame rate  
— say, 60 Hz — that you can have the iScan run in locked mode (see below) for 60 Hz sources while  
applying 50Hz to 60Hz frame rate conversion for all 50Hz sources.  
Screen Aspect Ratio  
(2.35:1)  
Screen Aspect Ratio  
(2.35:1)  
Mask  
underscan represents the visible display area, a sub-set of the active output area. underscan is like  
a negative zoom which preserves the aspect ratio of the active area. The default for this setting is 0.  
as you increase underscan, the smaller portion of the active display area appears while preserving the  
Image  
aspect ratio of the active display area. The frame Geometry Test pattern should be used while making  
Locked mode (1:1): This means that the iscans output frame rate tracks the input rate i.e., the  
output rate is locked to the input rate. In the 1:1 mode — i.e., 60 Hz source-locked to 60 Hz, and  
50 Hz source-locked to 50 Hz — there is always exactly one output frame for every input frame/  
field. This mode has the advantage that there are never any dropped or repeated frames (unless  
the source itself does this). one disadvantage of this mode is that when the video source is changed,  
the iscan has to re-lock to the new input signal timing. This causes a disruption in the iscans  
output signal while the locking process occurs, and can cause many displays to loose sync to the  
iscans signal and temporarily blank.  
this adjustment.  
Visible Area  
Active  
Output  
Image  
Visible Area  
Active  
Output  
Unlocked mode: This means that the iscans output frame rate is independent of the input rate.  
Regardless of any variations in the input, the output frame rate will be fixed at the specified value.  
This mode results in the most stable output signal as it’s independent of any changes in the input  
29  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
signal. Unlike the locked mode(s), the iScan’s output signal timing will not be disrupted when the  
input source is changed. However, it’s guaranteed to cause dropped or repeated frames as the input  
and output frame rates are not the same. note that regardless of what number the unlocked output  
frame rate is set to, it will never be identical to the input rate in this mode as the output signal timing  
is independent of the input timing. These dropped/repeated frames can result in visible irregularities  
in smooth motion, sometimes called motion judder or stutter.  
source-locked for 60 Hz sources, and 50 Hz locked (or unlocked, if desired) for 50 Hz sources.  
If the higher frame rate (72/75) is desired or required, then both source types can be config-  
ured for the 3:3 source-locked output option. For non-film material you may find that there’s  
too much motion stutter, although that tends to be a very personal thing as not everyone  
perceives this the same way (as with low frame rate display flicker).  
Border Level  
The border level setting is global, that is, there is only one border level setting for the system.  
To adjust the border level, push the por qbutton. The current level is shown. The default value is  
‘0. push the por qbutton to decrease or increase the border level.  
Locked mode (2:2 or 3:3): For standard definition interlaced sources the iScan can detect 2:2  
and 3:2 pulldown cadences and convert these to either a 2:2 or 3:3 frame repetition rate. The main  
advantage of this is for 60 Hz sources using 3:2 pulldown, as the irregular 3:2 pattern can be  
converted to 2:2 at 48 Hz or 3:3 at 72 Hz. In these modes, each original film frame is repeated  
exactly 2 or 3 times, respectively, and motion is therefore smoother. Note that these modes are only  
useful when the video source is film-based — i.e., 3:2 pulldown for 24 Hz film on 60 Hz sources, and  
2:2 pulldown for 25 Hz film on 50 Hz sources. If the source is not film-based, then the end result is  
a lot like unlocked mode without that modes stability advantages.  
Picture Controls  
The iscan Vp50pro has picture memories for each accepted format that are automatically saved and  
recalled on each input. in addition to these controls, the iscan Vp50pro has output picture controls  
that can be used for multiple applications. one application is to save two separate output modes  
for day/night usage where the ambient light changes. another application is two adjust the output  
for separate connected displays. There are two user modes available, titled ‘preset ꢀ’ and ‘preset 2.  
To make adjustments to one of these modes, first select the desired mode in the ‘Preset’ submenu  
and then make the desired changes to the output picture Controls.  
Motion-judder test pattern: The iscan has a built-in test pattern generator to help you deter-  
mine which frame rates your display supports. This is the test pattern with the vertical bar which  
pans horizontally back and forth across the screen. Note that this test pattern is used to determine  
the capabilities of your display, and does not provide any indication of motion smoothness (or lack  
thereof) in the iscans output. The test pattern is used with the unlocked output mode of the iscan.  
You set the (unlocked) output frame rate to be the one you’re testing your display for, and  
observe if the back and forth panning motion of the test pattern is smooth or if it jerks or stutters.  
if the former, then the display supports that particular resolution and frame rate without perform-  
ing any frame rate conversion of its own; if the latter, then the display is performing frame rate  
conversion on the signal.  
These modes can be recalled using the Viewing Modes button on the remote control.  
There are also three additional modes which can be saved by a calibrator who has been trained by  
the imaging science foundation on proper display calibration methodology. These modes are titled  
‘isf day normal, isf day bright’ and ‘isf night.  
More information about the imaging science foundation is available at www.imagingscience.com  
Examples. These configuration options provide a lot of flexibility to deal with differing source and  
HDCP Mode  
display characteristics. Let’s look at a few examples:  
There are two HdCp modes:  
A. The display only supports 60 Hz input. In this case, the iScan must produce a (nominal)  
60 Hz output. For 60 Hz sources you can run in either 1:1 source-locked mode, or  
in unlocked mode with the output frame rate set to approximately 60 Hz. You might  
choose unlocked mode if the display takes a long time to re-sync to new inputs and  
you channel-surf a lot. locked mode will provide the smoothest motion and guaran-  
tee no dropped or repeated frames. For 50 Hz sources, you’d set the iScan’s output  
to unlocked with a (nominal) 60 Hz frame rate. This will result in some motion  
irregularities as the iScan periodically repeats frames to convert the 50 Hz input to  
the 60 Hz output rate, but since the display only supports 60 Hz inputs there’s not  
much you can do.  
Off: HdCp is disabled at the iscan Vp50pros HdMi output.  
On: The iscan Vp50pro continuously looks for a HdCp display device on its HdMi output.  
This is the default setting.  
NOTE: The iscan Vp50pro is not designed to remove HdCp from a protected signal. if this setting is set  
to ‘on’ make sure that the corresponding HdCp Mode setting on the input is also set to ‘on.  
12V Triggers  
The two ꢀ2-volt trigger ports are designed to supply a combined total of 500ma which is split between  
the two devices based on their draw, so one device can draw up to 495ma if the other only draws  
5ma — or both can draw 250ma. These devices do not need to have the same current draw to work.  
This is enough current to drive one or two ꢀ2-volt relays, suitable for turning on a lens and projector,  
for example. If the combined draw exceeds 500mA, the video processor is protected against over-  
load. The state of the 12V triggers can individually be adjusted in the ‘Configuration’ menu. This is  
helpful if the default state of the connected device is incorrect. For example a screen may be set to  
go up, when in fact the desired state for the screen is to be down.  
B. The display only supports 50 Hz input. This is the opposite of case A, and the required  
configuration is also the opposite — i.e., the output frame rate for 60 Hz source should be  
set to 50 Hz unlocked, and the rate for 50 Hz sources can be set to either 1:1 locked or  
unlocked at 50 Hz (for all the same reasons noted in the first example).  
C. The display supports a wide range of frame rates (e.g., a front projector). In this case  
you can configure things most any way you like. If motion judder with 3:2 pulldown  
bothers you, then use the iScan’s 24Hz, 48 Hz or 72 Hz source-locked output options for  
film-based 480i sources. If not, then 60 Hz locked is a good choice. For 50 Hz sources,  
unless you notice display flicker at 50 Hz, you’d probably want to run at 50 Hz locked to  
avoid repeated/dropped frames.  
When the Trigger Level is set to “Normal, it will supply +12vdc on the TIP when active, and will pull  
the TIP to Ground (0vdc), referenced to the SHIELDwhen inactive. When the trigger port is set to  
“Negative, it will pull the TIP to Ground (0vdc), referenced to SHIELDand will supply +12vdc to the  
TIP when inactive. The SHEILD will never carry the +12vdc supply signal. To ensure that damage  
is not caused, please check the manual of the device that you intend on connecting to the Vp50pro  
before inserting the trigger plug into the jack.  
D. A digital display supports a narrow range of frame rates, either around 50 Hz or  
72/75 Hz. If the display supports both 50 Hz and 48 Hz, and the primary use of 60 Hz  
source is film-based material, then you would likely want to configure the iScan as 48 Hz  
3ꢀ  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Trigger #1 is powered on when the iscan Vp50pro is powered on. Trigger #1 is powered  
off when the iscan Vp50pro is put into standby mode. This can be useful for powering on a  
display or motorizing a screen or lift.  
seCTion 5 –appendiX  
Complete Menu Tree  
Trigger #2 can be programmed to be powered on in the ‘output setup’ menu. This action  
can be saved as part of a Display Profile. The ‘Lens’ option facilitates use of an anamorphic  
lens.  
Input Select  
Video ꢀ  
Video ꢀ  
s-Video ꢀ  
s-Video 2  
Installer Note: The trigger ports are outputs and are not designed to directly receive a ꢀ2-volt  
trigger signal from another device, like an amplifier, automation controller or 12-volt power supply.  
Care has been taken in the design to ensure that if this was done, no harm should come to the video  
processor but it is strongly recommend that other devices are checked to ensure that the trigger  
ports on the Vp50pro are not being “back-fed.  
Component ꢀ  
Component 2  
rGbHV/Component  
HdMi ꢀ  
HdMi 2  
HdMi 3  
HdMi 4  
Driving Relays: When driving a relay from the 12-volt trigger port(s), we strongly recommend  
wiring a clamping diode in parallel to suppress transient spikes when the relay is turned off. some  
relays include a clamping diode within the relay package. if it is unknown whether the relay includes  
a clamping diode, check the relay coil with an ohmmeter – with the red and black leads touching  
the coil pins one way the Ohmmeter should read approximately 0 Ohms resistance (+/-0.4 Ohms),  
and with the leads red and black leads switched the ohmmeter should read between ꢀ8 ohms and  
100 Ohms. If the same value is indicated for both directions (and it’s above 1 Ohm), add a standard  
“general diodelike a 1N4001 (can be found at any electronic components store) across the relay  
coil pins (see the figure below for connection diagram).  
auto  
Input Aspect Ratio  
frame ar  
active ar  
4:3  
ꢀ6:9  
ꢀ.33:ꢀ  
ꢀ.55:ꢀ  
ꢀ.66:ꢀ  
ꢀ.78:ꢀ  
ꢀ.85:ꢀ  
2.35:ꢀ  
user  
panorama  
Zoom  
on  
off  
Horizontal  
range: 0-ꢀ00  
range: 0-ꢀ00  
Vertical  
pan  
Horizontal  
range: 0-ꢀ00  
range: 0-ꢀ00  
Vertical  
borders  
presets  
Horizontal  
range: 0-200  
range: 0-200  
Clamping diode polarity and connection to relay coil  
Vertical  
4:3 full frame  
Letterbox  
ꢀ6:9 full frame  
4:3 stretch  
preset ꢀ  
Solid State Loads: The ꢀ2-volt triggers do not have a minimum load requirement, which enables  
our triggers to drive solid state control devices (MOSFETs and optocouplers) found within newer  
devices.  
preset 2  
preset 3  
preset 4  
Display Profiles  
preset 5  
A Display Profile is a user-defined preset which contains all settings from the output setup menu.  
preset 6  
More information can be found on page ꢀ7.  
preset 7  
preset 8  
preset 9  
preset ꢀ0  
33  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
user  
rGb  
save user to  
YPbPr  
preset ꢀ  
YCbCr 4:2:2  
YCbCr 4:4:4  
auto  
no  
Yes  
preset 2  
preset 3  
preset 4  
preset 5  
preset 6  
preset 7  
preset 8  
preset 9  
preset ꢀ0  
input level  
VCr Mode  
no  
Video  
Yes  
pC  
no  
off  
Yes  
on  
auto  
no  
HDMI Config.  
Yes  
HdCp Mode  
auto ar  
on  
off  
no  
Yes  
on  
off  
no  
Yes  
auto Color space  
off  
on  
no  
Yes  
auto priority  
audio input  
range: ꢀ-ꢀ3  
no  
Yes  
audio ꢀ  
audio 2  
audio 3  
audio 4  
stereo  
HdMi  
no  
Yes  
no  
Yes  
off  
Input Adjust  
aV lipsync  
Mosquito noise  
reduction  
range: 0-200  
Picture Control  
off  
fine detail  
edge enhancement  
brightness  
Contrast  
low  
range: -50-50  
range: -50-50  
range: -50-50  
range: -50-50  
range: -50-50  
range: -50-50  
range: -50-50  
Medium  
High  
deinterlacing  
auto  
film bias Mode  
forced Modes  
Video Mode  
forced 3:2  
forced 2:2  
2:2 even  
saturation  
Hue  
2:2 odd  
Y/C Delay  
Game Mode ꢀ  
Game Mode 2  
Cue Correction  
prep  
off  
off  
on  
on  
auto  
pass Through  
preset  
off  
on  
isf day normal  
isf day bright  
isf night  
overscan  
range: 0-20  
Horizontal  
Vertical  
preset ꢀ  
image shift  
preset 2  
Configuration  
range: 0-30  
range:0-30  
Test patterns  
frame/Geometry  
brightness/Contrast  
Color space  
35  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Checkerboard  
Vertical lines  
Horizontal Lines  
Judder  
information  
Output Setup  
analog/digital  
BNC (Analog)  
HDMI (Digital)  
Color8 bars75  
Color8 barsꢀ00  
Window ireꢀ0  
Window ire20  
Window ire30  
Window ire40  
Window ire50  
Window ire60  
Window ire70  
Window ire80  
Window ire90  
Window ireꢀ00  
Gray ramp  
Xhatch Coarse  
Xhatch fine  
focus  
format  
480p  
540p  
576p  
720p-50  
720p-60  
ꢀ080i-50  
ꢀ080i-60  
ꢀ080p-24  
ꢀ080p-25  
ꢀ080p-50  
ꢀ080p-60  
640x480 (VGA)  
800x600 (SVGA)  
1024x768 (XGA)  
1280x1024 (SXGA)  
848x480  
Half b/W  
H-Clr7 bars75  
H-Clr7 barsꢀ00  
H-Clr8 bars75  
H-Clr8 barsꢀ00  
black  
852x480  
1365x768  
852x576  
1366x768 (1)  
1366x768 (2)  
1360x768 (1)  
1360x768 (2)  
1280x768  
1024x1024  
1024x852  
1024x768  
1024x576  
848x600  
White  
red  
Green  
blue  
Cyan  
Magenta  
Yelllow  
auto standby  
off  
on  
1365x1024  
1400x1050  
1400x788  
960x540  
led brightness  
navigation  
normal  
range: 0-3  
range: 0-3  
1280x960  
1440x960  
1440x1152  
user  
user Mode  
normal  
Horizontal Shift  
Horizontal Size  
advanced  
range:  
range:  
range:  
range:  
range:  
range:  
range:  
range:  
range:  
range:  
serial port rate  
4800  
9600  
Horizontal Front Porch  
Horizontal Sync  
Horizontal Back Porch  
Vertical shift  
ꢀ4400  
ꢀ9200  
38400  
57600  
factory default  
no  
Yes  
software update  
12V Trigger (Levels)  
Vertical Size  
no  
Yes  
Vertical front porch  
Vertical sync  
Trigger #1  
Trigger #2  
normal  
negative  
Vertical back porch  
normal  
aspect ratio  
negative  
37  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
display  
lens  
picture Control  
4:3  
presets  
5:4  
isf day normal  
isf day bright  
isf night  
ꢀ6:9  
Custom  
preset ꢀ  
Mode ꢀ  
preset 2  
Mode ꢀ - auto  
Mode 2  
brightness  
Contrast  
none  
saturation  
Hue  
screen  
4:3  
Gamma Control  
ꢀ6:9  
off  
on  
2.35:ꢀ  
Custom  
range: ꢀ.00-3.00  
red  
range: 0.5-2.5  
Green  
range: 0.5-2.5  
blue  
range: 0.5-2.5  
image shift  
underscan  
Vertical  
range: -30-30  
range: -30-30  
Horizontal  
user  
HdCp Mode  
range: 0-ꢀ00  
off  
on  
sync Type  
bi-level  
Tri-level  
Composite  
H+/V+  
H+/V-  
12V Trigger #2  
lens  
on  
off  
Display Profile  
H-/V+  
select  
H-/V-  
Profile 1  
Profile 2  
Profile 3  
Profile 4  
Profile 5  
Profile 6  
Profile 7  
Profile 8  
Profile 9  
Profile 10  
Color space  
rGb  
YPbPr  
YCbCr 4:2:2  
YCbCr 4:4:4  
output level  
framerate  
Video  
pC  
24Hz  
save  
24Hz Lock  
48Hz Lock  
60Hz Lock  
72Hz Lock  
unlock  
Profile 1  
Profile 2  
Profile 3  
Profile 4  
Profile 5  
Profile 6  
Profile 7  
Profile 8  
no  
Yes  
no  
25Hz  
50Hz  
60Hz  
Yes  
25Hz Lock  
50Hz Lock  
75Hz Lock  
unlock  
no  
Yes  
no  
25Hz Lock  
50Hz Lock  
75Hz Lock  
unlock  
Yes  
no  
Yes  
24Hz Lock  
48Hz Lock  
60Hz Lock  
72Hz Lock  
unlock  
no  
Yes  
no  
Yes  
border level  
range: -ꢀ6-ꢀ00  
no  
39  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Yes  
Profile 9  
no  
Yes  
Profile 10  
no  
Yes  
auto  
off  
on  
4ꢀ  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
43  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Crown Audio Stereo Amplifier SST 4632 User Manual
Curtis Clock Radio CR4975 User Manual
Danby Refrigerator DFF100A2WDB User Manual
Electro Voice Microphone RE50 B User Manual
Fisher Paykel Humidifier MR850 User Manual
Fisher Paykel Oven BI600ED User Manual
Fisher Paykel Oven OB24SDPX User Manual
Gefen Switch DVI Hub User Manual
GE Washer Dryer EWA6500 User Manual
Gigabyte Network Router GN BR404W User Manual