Curtis Cordless Telephone TC972 User Manual

TC972 english.qxd 4/13/2004 10:58 AM Page 1  
OWNER'S MANUAL  
In Use  
Low Batt  
Page  
TALK  
Redial  
Flash  
3
1
2
In Use/Chg  
def  
Power  
abc  
4
6
5
ghi  
mno  
jkl  
7
w9xyz  
#
8
pqrs  
tuv  
0
*
Memo  
Scan  
Pause  
Tone  
2.4 GHz Cordless Telephone  
PLEASE READ BEFORE OPERATING THIS EQUIPMENT  
Model : TC972  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TC972 english.qxd 4/13/2004 10:58 AM Page 3  
Safety Instructions  
IMPORTANT SAFETY INSTRUCTIONS  
To reduce the risk of fire, electric shock and/or injury, always follow these  
basic safety precautions when using your cordless telephone equipment.  
1. Read and understand all instructions.  
2. Follow all warnings and instructions marked on the telephone.  
3. Do not use this telephone near a bathtub, wash bowl, kitchen sink, or laundry tub, in a wet  
basement, near a swimming pool, or anywhere else where there is water.  
4. Avoid using a telephone (other than a cordless type) during an electrical storm. There may  
be a remote risk of electric shock from lightning.  
5. Do not use the telephone to report a gas leak in the vicinity of the leak.  
6. Use only the power cord and Battery Pack indicated in the Owner’s Manual. Do not dispose  
of the Battery Pack in a fire. The Battery Pack may explode. Check with local codes for  
possible special disposal instructions.  
7. Operate this telephone using the electrical voltage as stated on the Base Unit or in the  
Owner’s Manual. If you are not sure of the voltage in your home, consult your dealer or local  
power company.  
8. Unplug this telephone from the wall outlet before cleaning or replacing the Battery Pack. Do  
not use liquid cleaners or aerosol cleaners on the telephone. Use a damp cloth for cleaning.  
9. Place this telephone on a stable surface. Serious damage and/or injury may result if the  
telephone falls.  
10. Do not cover the slots and openings on this telephone. This telephone should never be  
placed near or over a radiator or heat register. This telephone should not be placed in a  
built-in installation unless proper ventilation is provided.  
11. Do not place anything on the power cord. Install the telephone where no one will step or trip  
on the cord.  
12. Do not overload wall outlets or extension cords as this can increase the risk of fire o  
electric shock.  
13. Never push any objects through the slots in the telephone. They could touch dangerous  
voltage points or short out parts that could result in a risk of fire or electric shock. Never spill  
liquid of any kind on the telephone.  
14. To reduce the risk of electric shock, do not take this telephone apart. If service or repair work  
is required on this telephone, take it to a qualified service representative. Opening or  
removing covers may expose you to dangerous voltage or other risks. Incorrect reassembly  
can cause electric shock when the appliance is subsequently used.  
15. Unplug this telephone from the wall outlet and consult a qualified service representative in  
any of the following situations.  
A. When the power supply cord is frayed or damaged.  
B. If liquid has been spilled into the telephone.  
C. If the telephone has been exposed to rain or water.  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
TC972 english.qxd 4/13/2004 10:58 AM Page 4  
Safety Instruction  
D. If the telephone does not operate normally by following the operating instructions. Adjust  
only those controls that are covered by the operating instructions. Improper adjustment may  
require extensive work by a qualified technician to restore the telephone to normal  
operation.  
E. If the telephone has been dropped or the case has been damaged.  
F. If the telephone exhibits a distinct change in performance.  
16. Never install telephone wiring during a lightning storm.  
17. Never install telephone jacks in wet locations unless the jack is specifically designed for wet  
locations.  
18. Never touch uninsulated telephone wires or terminals unless the telephone line has been  
disconnected at the network interface.  
19. Use caution when installing or modifying telephone lines.  
Battery Safety  
CAUTION:  
Risk of explosion if Battery Pack is replaced by an incorrect type. Replace  
only with the same or equivalent type. Dispose of used batteries according  
to the instructions. To reduce the risk of fire or personal injury, read and  
follow this instructions.  
1. Use only the following type and size of Battery Pack:  
3.6V, 600mAh Nickel Metal Hydride Ni-MH Battery Pack  
2. Do not dispose of the Battery Pack in a fire. It may explode. Check with local codes for  
possible special disposal instructions.  
3. Do not open or mutilate the Battery Pack. Released electrolyte from a Battery Pack is  
corrosive and may cause damage to the eyes or skin. Electrolyte may be toxic if swallowed.  
4. Exercise care in handling the Battery Pack to prevent shorting the Battery Pack with  
conductive materials such as rings, bracelets, and keys. The Battery Pack or conductor  
may overheat and cause burns.  
5. Charge the Battery Pack provided with (or identified for use with) this telephone only in  
accordance with the instructions and limitations specified in this manual.  
6. Observe proper polarity orientation between the Battery Pack and Battery Charger.  
SAVE THESE INSTRUCTIONS  
ATTENTION:  
The telephone that you have purchased contains a rechargeable Battery Pack. The Battery Pack  
is recyclable. At the end of its useful life, under various state and local laws, it may be illegal to  
dispose of this Battery Pack into the municipal waste stream. Check with your local solid waste  
officials for details in your area for recycling options or proper disposal.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
TC972 english.qxd 4/13/2004 10:58 AM Page 5  
Handset Controls  
1. In use / Low Batt  
(Battery) LED  
Indicator  
8. Handset Receiver  
9. Redial Button  
2. TALK Button  
3. Flash Button  
10. Headset Jack  
4. Handset Volume Control  
11. Ringer ON/OFF  
Switch (Hi, Mid, Low)  
Switch  
5. Memo Button  
6. Pause Button  
7. Microphone  
12. Scan Button  
13. Tone Button  
14. Charge Contacts  
1. In use /Low Batt (Battery) LED Indicator - Lights up when the Hadset is in TALK  
mode. Blinks when the battery charge is low.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
TC972 english.qxd 4/13/2004 10:58 AM Page 6  
Handset Controls  
2. Talk button - Press to answer an incoming call or to place a call. Press to end the call.  
3. Flash button - Press to answer an incoming call if you have Call Waiting.  
4. Handset Volume Control (LOW, MID, HI) switch - Select the receiver volume level.  
5. Memo button - Press to store phone numbers in memory or to call a number you have  
previously stored.  
6. Pause button - Press to insert a Pause while dialing. (You will need the Pause button to dial  
numbers which use an alternative Long Distance Access Code.)  
7. Microphone  
8. Handset Receiver  
9. Redial button - Press to Redial the last number you called.  
10. Headset Jack - For connecting your headset plug to enjoy hands-free communication. (See  
page 12 for detail).  
11. Ringer ON/OFF switch - Switch to ON to engage the ringer on the Handset. Set switch to  
OFF to disengage the ringer on the Handset. Remember to return to “ON” position when  
you are ready to receive calls.  
12. Scan button - Press to change the operating channel when you hear interference.  
13. Tone button - Press to change the dialing mode from PULSE to TONE.  
14. Charge Contacts - For charging the Battery Pack inside the Handset. We recommend  
cleaning the Charge Contacts periodically with a damp cloth.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
TC972 english.qxd 4/13/2004 10:58 AM Page 7  
Base Unit Controls  
1. Tone/Pulse Select Switch  
2. Power-In Connection Jack  
3. Telephone Line Connection Jack  
12VDC  
200mA  
TONE /P ULSE  
TEL LINE  
4. Base Unit Antenna  
5. Page button  
Page  
6. Charge Terminals  
In Use/Chg  
Power  
7. Power LED Indicator  
8. In Use/Charge LED Indicator  
1. Tone/Pulse Select Switch  
2. Power-In Connection Jack  
3. Telephone Line Connection Jack  
4. Base Unit Antenna  
5. Page button - Press to page the Handset  
6. Charge Terminals - For charging the Handset battery pack. For best performance, clean  
the Charge terminals periodically with a damp cloth.  
7. Power LED Indicator - Lights up when power I connected to the Base Unit.  
8. In Use/Charge LED Indicator - (IN USE) Lights up to indicate that the Handset is in TALK  
mode. (CHARGE) Lights up when the Handset is placed on the Base Unit for charging.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
TC972 english.qxd 4/13/2004 10:58 AM Page 8  
Getting Started  
Carefully remove your cordless telephone from its shipping carton. If there is any visible  
damage, do not attempt to operate this equipment. Return it to the place of purchase.  
Check to be sure you have all items that come with this cordless telephone system. You should  
have a Handset, Base Unit, AC Adaptor, Battery Pack, Telephone Line Cord, Belt Clip, and  
Owner’s Manual.  
InUse  
Low Batt  
Page  
AC Adaptor  
Belt Clip  
TALK  
Flash  
1
Redial  
3
2
In Use/Chg  
def  
Power  
abc  
4
6
5
ghi  
mno  
jkl  
7
wx9yz  
#
Scan  
tu8v  
0
pqrs  
*
Memo  
Pause  
Tone  
Telephone Line Cord  
Battery Pack  
Handset  
Base Unit  
Connecting your Phone  
This section is a reference guide to the basic functions and operations of your cordless telephone.  
For more detailed descriptions of the operations and features of this telephone, refer to the  
Contents on page 1.  
1. Insert the small plug on the end of the AC Adaptor into the Power-In Connection Jack at the  
back of the Base Unit.  
2. Plug the AC Adaptor into a 120V wall outlet Use only Class 2 power source 12V DC, 200mA.  
120V WALL  
OUTLET  
TELEPHONE LINE  
CONNECTION  
JACK  
TELEPHONE  
JACK  
POWER-IN  
CONNECTION  
JACK  
12VDC  
200mA  
TONE/PULSE  
L LINE  
TELEPHONE  
LINE CORD  
AC  
ADAPTOR  
TONE/PULSE  
SELECT SWITCH  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
TC972 english.qxd 4/13/2004 10:58 AM Page 9  
Getting Started  
3. Insert one plug of the Telephone Line Cord into the house Telephone Jack and the other end  
into the Telephone Line Connection Jack at the back of the Base Unit. ( If you have and older  
4-prong Telephone Jack, you will need an RJ-11C Telephone Jack Adaptor. This Adaptor is  
available at the same place you purchased you telephone.  
CAUTION: The cordless telephone operates at a frequency that cause interference to nearby  
TVs and VCRs; the base phone should not be placed near, or on top of a TV or VCR. If  
interference is experienced, moving the cordless telephone farther away from the TV or VCR  
will often reduce or eliminate the interference.  
Battery Installation  
To install the 3.6V 600mAh cordless Handset  
battery pack:  
1. Install the Handset Battery Pack by plugging it into  
the Battery connector inside the Battery  
compartment. Place the Battery Pack inside the  
Battery Compartment.  
BATTERY PACK  
2. Slide the Handset Battery compartment cover  
firmly into place in its closed position  
3. Once you have installed the Battery Pack and  
placed the Handset on the cradle you will hear a  
tone indicating the Handset has connected with  
the charging contacts and will successfully charge.  
BATTERY  
COMPARTMENT  
COVER  
4. IMPORTANT: Before initial use, charge the  
Handset for 12 hours.  
Battery Duration  
A fully charged battery lasts for approximately:  
4 hours when you use the Handset continuously (talk time).  
5 days when the Handset is not in use (standby).  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
TC972 english.qxd 4/13/2004 10:58 AM Page 10  
Getting Started  
TONE/PULSE Select Switch:  
A. If your home is equipped with a tone dialing system, set the TONE/PULSE Select Switch  
to the TONE position.  
B. If you have a rotary dialing system, set the TONE/PULSE Select Switch to the PULSE  
position.  
C. If you are not sure which system you have, set the TONE/PULSE Select Switch to the  
TONE position. Press the TALK button on the Handset and make a call. If the call  
connects, leave the switch as is; otherwise set to the PULSE position.  
Belt Clip Installation  
BELT CLIP  
HOOK  
With the back of the Handset facing up, insert one  
side of the Belt Clip Hook into the matching slot at the  
top side of the Handset. Press down on the opposite  
side of the Belt Clip until the other hook locks into the  
slot on the side of the Handset.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
TC972 english.qxd 4/13/2004 10:58 AM Page 11  
Cordless Telephone Operation  
Preparing for Use  
Before you can use your cordless telephone, you must charge the Handset for 12 hours. Failure  
to do so will require recharging of the Battery Pack more often.  
1. Place the Handset on the Base Unit for 12 hours.  
2. After 12 hours, remove the Handset from the Base Unit.  
NOTE: Depending on the frequency of use, once the Handset is fully charged, it remains  
functional for approximately 6 hours of continuous use and approximately 6 days when  
the Handset is off the Base Unit in standby mode.  
Placing Calls  
1. Press the TALK button. The Handset IN USE LED  
indicator and the Base Unit IN USE/CHARGE LED  
indicator will light up.  
2. Listen for a dial tone.  
3. Dial the phone number.  
In Use  
Low Batt  
4. When you have finished your call, either press the TALK  
button or place the Handset on the Base Unit. The  
TALK  
Redial  
3
Flash  
1
Handset IN USE LED indicator will turn off and the  
Base Unit IN USE/CHARGE LED will light up to  
indicate that the Handset is charging.  
2
NOTES:  
1. The Base Unit does not have a ringer and does not ring when receiving an incoming call.  
2. If you are too far away from the Base Unit, the Handset emits “beep” sounds to warn  
you that the background noise level is too high for proper communication between the  
Handset and the Base Unit. When you hear this sound, you should move closer to  
the Base Unit to reduce the noise level. Otherwise, the call will automatically cut off.  
Receiving Calls with the Handset off the Base Unit  
1. When the phone rings, press the TALK button. The IN USE LED indicator will light up.  
2. Start your conversation.  
3. To end your conversation, either press the TALK button or place the Handset on the  
Base Unit. If you place the Handset on the Base Unit CHARGE CRADLE, you activate the  
automatic standby feature.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TC972 english.qxd 4/13/2004 10:58 AM Page 12  
Getting Started  
Receiving Calls with the Handset on the Base Unit  
1. When the phone rings, lift the Handset.  
The IN USE LED indicator will light up.  
NOTE: The Handset RINGER ON/OFF  
switch must be in the “ON” position for  
ringer to operate.  
2. Start your conversation.  
3. To end your conversation, either press the  
TALK button or place the Handset on  
the Base Unit. If you place the Handset on  
the Base Unit CHARGE CRADLE, you  
activate the automatic standby feature.  
Storing Numbers  
1. Be sure the Base Unit IN USE LED  
indicator is off and the Handset is in  
standby mode.  
2. Press the MEMO button.  
3. Dial the number you want to store.  
4. Press the MEMO button again.  
5. Dial the Keypad 0~9 button where you  
want to store that number. You will hear  
one confirmation “beep.”  
6. Repeat steps 1 through 5 to store other  
telephone numbers.  
EXAMPLE : To store the number 115-1968 under the Keypad 1 button:  
1 - Press the MEMO button.  
2 - Dial 115-1968.  
4 - Press the keypad 1 button.  
5 - You have stored 115-1968 under keypad 1 button.  
3 - Press the MEMO button again.  
A total of 10 telephone numbers can be programmed in memory.  
IMPORTANT: The maximum number of digits that can be stored for any phone number is 16 in  
PULSE or TONE mode. The maximum number of digits for mixed (TONE and PULSE in  
combination) dialing is 15. If you are using a switchboard system to access an outside line (such  
as an 8 or 9), press the PAUSE button to store a Pause.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TC972 english.qxd 4/13/2004 10:58 AM Page 13  
Getting Started  
Recalling Stored Numbers from Memory  
1. Press the TALK button.  
2. Press the MEMO button.  
3. Press the keypad button for the number you have stored. The stored number will be dialed  
automatically.  
EXAMPLE: To recall number 115-1968 stored under the keypad 1 button:  
1 - Press the TALK button.  
2 - Press the MEMO button.  
3 - Press the keypad 1 button.  
Redial Feature  
1. If you get a busy tone, press the TALK button to hang up.  
2. Later, press the TALK button again.  
3. Listen for a dial tone.  
4. Press the REDIAL button. This will automatically redial the last telephone number you called.  
Mixed Mode (Temporary Tone) Dialing  
If you only have Pulse (rotary dialing) service in your area set the TONE/PULSE select switch at  
the rear of the Base Unit to PULSE position. If you want to access tone dialing mode, press  
the TONE button on the Handset and dial the desired number, subsequent digits will be dialed  
into Tone mode. Pulse mode will reset after the Handset is returned on-hook.  
Using the Headset Feature  
Your telephone can utilize a headset (included) to  
be connected to your Handset for you to enjoy  
hands-free communication.  
Insert the small plug on the end of the headset into  
the Headset Jack at the right side of the  
Handset. Follow the procedures discussed in  
“Receiving Calls” and Placing Calls” to receive and  
place a call.  
NOTE: When you plug the headset plug into the  
Headset Jack it automatically mutes the  
Microphone and Speaker of the  
Handset. Unplug the headset to return  
the Handset to normal use.  
The Headset Jack is compatible with 2.5 mm  
headset plugs only.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TC972 english.qxd 4/13/2004 10:58 AM Page 14  
Security  
Your cordless telephone uses a digital coding security system to prevent unauthorized use of your  
telephone line by another nearby cordless telephone. The system has its own identifying signal  
created by microcomputers in both the Base Unit and the Handset.  
Security Code  
This telephone has an internal security code with 65,536 possible combinations.  
Resetting Security Code and Channel Information  
Communication between the Handset and the Base Unit may not be possible in any of the  
following situations:  
1. After a power failure.  
2. After relocating the Base Unit by disconnecting the AC ADAPTOR.  
3. After replacing the Handset Battery Pack.  
To reset, place the Handset on the Base Unit for 2 to 5 seconds.  
Multi-Channel Access  
Your cordless telephone lets you select a channel from the 50 frequencies available to transmit  
signals between the Base Unit and the Handset. When you notice interference from other  
cordless telephones, change to another channel by pressing the SCAN button on the Handset.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TC972 english.qxd 4/13/2004 10:58 AM Page 15  
Recharging the Battery Pack  
The nickel metal hydride (Ni-MH) Battery Pack in the Handset can be recharged many times  
using the built-in charger in the Base Unit.  
When the BATT LOW LED indicator starts to blink rapidly, a “beep” sound will be heard every 12  
seconds. This indicates that the Battery Pack needs to be recharged.  
Charge the Battery Pack at least once every 90 days of non-use to avoid battery failure. When  
the Battery Pack can no longer be charged, replacement of the Battery Pack will be necessary.  
NOTES:  
1. During a power interruption, the Base Unit does not operate, and a phone conversation  
cannot be made on the Handset.  
2. To ensure your phone charges properly, make sure that the CHARGE LED indicator on  
the BASE UNIT lights up and a “beep” confirmation tone is heard.  
Changing the Battery Pack  
The Battery Pack provides power for the Handset of your cordless telephone.  
To Replace the Battery Pack  
1. Remove the Handset Battery Compartment Cover by sliding it down.  
2. Pull out the Battery Pack PLUG and remove the Battery Pack. See “Battery Installation”  
Pack on page 8.  
ATTENTION:  
The telephone that you have purchased contains a rechargeable Battery Pack. The Battery  
Pack is recyclable. At the end of its useful life, under various state and local laws, it may  
be illegal to dispose of this Battery Pack into the municipal waste stream. Check with your  
local solid waste officials for details in your area for recycling options or proper disposal.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TC972 english.qxd 4/13/2004 10:58 AM Page 16  
Problem Solving  
For your assistance, we have listed below a few common problems.  
Phone does not work, check the following:  
1. Base Unit is plugged into a power source.  
2. Handset is charged.  
3. TONE/PULSE Select Switch is in the right position.  
4. Telephone Line Cord is plugged into the Telephone Jack.  
Range of phone limited, check the following:  
1. Base Unit is centrally located in your residence.  
2. Base Unit is not located near appliances.  
No dial tone, check the following:  
1. TELEPHONE LINE CORD plugs are connected to the Telephone Jack and Telephone Line  
Connection Jack.  
2. Base Unit is plugged into a power source.  
3. If you had a power failure or had unplugged the Base Unit, replace the Handset on the  
Base Unit for 2 to 5 seconds to reset the system.  
Received signal flutters or fades, check the following:  
1. Battery Pack in the Handset is fully charged.  
2. Handset is not too far from the Base Unit.  
Excess static, check the following:  
1. Check to see that the Antenna is not touching another metal object.  
Interference on reception, check the following:  
1. Noise may be picked up from electrical products in the home or electrical storms. Generally,  
this noise is a minor annoyance and should not be interpreted as a defect in your system. (See  
Technical Information on page 16).  
2. Choose an alternate channel using the SCAN button on the Handset.  
3. Do not use this telephone within 20 ft. of a microwave oven while it is working, as you may  
experience interference. This is a normal occurrence with 2.4 GHz phones and should not be  
interpreted as a defect in the product.  
If after pressing the TALK button, you receive three “beeps” and no dial tone,  
check the following:  
1. Base Unit is plugged into a power source.  
2. If you had a power failure or had unplugged the Base Unit, replace the Handset on the  
Base Unit for 2 to 5 seconds to reset the system.  
NOTE: If none of the telephones in the house are working, disconnect one set at a time to  
verify that none of the telephones are causing the problem. If you still have a problem after doing  
this, and your telephone still does not work, please contact your local phone company.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TC972 english.qxd 4/13/2004 10:58 AM Page 17  
Technical Information  
This cordless telephone uses radio frequencies to allow mobility. There are certain difficulties in  
using radio frequencies with a cordless telephone. While these are normal, the following could  
affect the operation of your system.  
Noise  
Electrical pulse noise is present in most homes at one time or another. This noise is most intense  
during electrical storms. Certain kinds of electrical equipment such as light dimmers, fluorescent  
bulbs, motors, and fans also generate noise pulses. Because radio frequencies are susceptible to  
these noise pulses, you may occasionally hear them in your Handset. Generally they are a  
minor annoyance and should not be interpreted as a defect in your system.  
Range  
Because radio frequency is used, the location of the Base Unit can affect the operating range.  
Try several locations in your home or office and pick the one that gives you the clearest signal to  
the Handset.  
Interference  
Electronic circuits activate a relay to connect the cordless telephone to your telephone line. These  
electronic circuits operate in the radio frequency spectrum. While several protection circuits are  
used to prevent unwanted signals, there may be periods when these unwanted signals enter the  
Base Unit. You may hear clicks or hear the relay activate while you are not using the  
Handset. If the interference occurs frequently, it can be minimized or eliminated by relocating  
the Base Unit. You can check for interference before selecting the final Base Unit location by  
plugging in the telephone.  
NOTICE:  
This cordless telephone uses radio communication between the Handset and the Base Unit and  
may not ensure privacy of communication. Other devices, including other cordless telephones,  
may interfere with the operation of this cordless telephone or cause noise during operation. Units  
not containing coded access may be accessed by other radio communication systems. Cordless  
telephones must not cause interference to any licensed radio service.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TC972 english.qxd 4/13/2004 10:58 AM Page 18  
FCC Information  
FCC NOTICE  
The FCC requires that you be advised of certain requirements involving the use of this telephone.  
1. This telephone is hearing aid compatible.  
2. This equipment complies with Part 68 of the FCC Rules. A label on the Base Unit of this  
equipment contains, among other information, the ACTA Product Number and the Ringer  
Equivalence Number (REN) for this equipment. You must, upon request, provide this  
information to your telephone company.  
3. The REN is also useful in determining the quantity of devices that you may  
connect to your telephone line and still allow these devices to ring when your telephone  
number is called. In most areas, but not all, the sum of the RENs for all devices  
connected to one line should not exceed five (5.0). To be certain of the number of devices  
that you may connect to your line, you should contact your local telephone company.  
4. If your telephone causes harm to the telephone network, the telephone company may  
temporarily disconnect your service. If possible, they will notify you in advance that  
temporary discontinuance of service may be required. However, when advanced written  
notice is not possible, the telephone company may temporarily discontinue service  
without notice if such action is necessary under the circumstances.  
5. The telephone company may make changes in its communication facilities, equipment,  
operations, or procedures that could affect the proper operation of your equipment. If they  
do, you will be provided with advance notice as to give you an opportunity to maintain  
uninterrupted service.  
6. This equipment may not be used on coin service provided by the telephone company.  
Connection to party lines is subject to state tariffs. (Contact your state public Utility  
Commission or Corporation Commission for information.  
7. An FCC compliant telephone cord and modular plug is provided with this equipment. This  
equipment is designed to be connected to the telephone network or premises wiring using  
a compatible modular jack which is Part 68 compliant. See Installation Instructions for  
details.  
8. Please follow instructions for repairing, if repairing any (e.g. battery replacement section),  
otherwise do not alter or repair any parts or device except specified.  
9. The USOC number of the registration jack for this equipment is RJ11C.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TC972 english.qxd 4/13/2004 10:58 AM Page 19  
FCC Information  
RINGER EQUIVALENCE NUMBER  
NOTICE: The Ringer Equivalence Number (REN) assigned to each terminal device provides an  
indication of the maximum number of terminals allowed to be connected to a telephone interface.  
The termination on an interface may consist of any combination of devices subject only to the  
requirement that the sum of the ringer equivalence numbers of all devices does not exceed 5.  
CAUTION:  
Users should not attempt to make such connections themselves, but should contact the  
appropriate electric inspection authority, or electrician, as appropriate.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Compaq Switch Interconnect Switch User Manual
Craftsman Lawn Mower 37416 User Manual
Crosley Washer Dryer CFW 8000GBL User Manual
Eclipse Fujitsu Ten Car Stereo System CD8445 User Manual
ELAN Home Systems VCR V883 User Manual
Electro Voice Speaker Force i Sub User Manual
ETA Systems Power Supply EPD10IEC CE User Manual
Fedders Humidifier AC1A Series User Manual
Frigidaire Air Conditioner THRU THE WALL AIR CONDITIONER User Manual
GE Oven JGBP31 User Manual