27-6-07
CR249
KEEPSAKE USB Turntable
Instruction Manual
27-6-07
910-264500-0010-100
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Welcome
Table of Contents
Thank you for purchasing the Crosley Keepsake
(CR249). Before operating this unit, please read this
manual thoroughly and retain it for future reference.
Getting Started
Turntable Operation
Accessory: ADAPTER FOR 45 RPM
Unpacking................................. 4
Power Source........................... 4
Control Locators....................... 5
This adaptor allows you to play 45 RPM records.
1
2
Turn the unit on by rotating the ON/OFF-
VOLUME KNOB (7) clockwise.
About This Manual
Set the SPEED CONTROL SWITCH (4) to
to the correct speed (33 1/3,45 or 78 rpm).
Instructions in this manual describe the control
functions of the CR249.
Operation
3
4
Place the record on the turntable.
Included in this package:
General.................................... 6
USB/Recording........................ 6
·
·
·
·
Keepsake USB Turntable
Record Recording Software
USB Cable
Use the CUE LEVER (2) to raise the tone arm
off its rest. Move the tone arm over the record
and use the cue lever to lower it onto the record.
The record will begin to turn automatically.
1
2
Place the 45 RPM adaptor over the spindle.
45rpm Adapter
Gently place your 45 RPM record onto the
turntable.
5
At the end of the record, the tone arm will return
to its rest.
3
Follow the steps under turntable operation to
play your record.
General
Troubleshooting Guide............ 7
Warranty................................... 8
USB Operation
Using the included software and cable, the USB
connection allows you record your records onto your
computer. Follow these instructions to use the USB.
1
2
Insert the enclosed software CD into your
computer.
Follow the instructions on the computer screen
to install the software. If the software does not
load automatically, browse the CD and open
the Read Me folder for further instructions.
3
4
5
6
Connect the small end of the USB cable to the
USB JACK (15) on the back of the unit.
Connect the other end to a USB port on your
computer.
On your computer, open the Record Recording
Software.
For instructions on operating the Record
Recording Software, browse the software CD
and open the Read Me folder.
6
3
Download from Www.Somanuals.com. All Manuals Search And Download.
General
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE
TO RAIN OR MOISTURE. DO NOT REMOVE COVER. PILOT LAMPS SOLDERED
IN PLACE. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO
Troubleshooting
QUALIFIED SERVICE PERSONNEL.
The unit does not operate.
1
The AC Power cord is not connected. Make sure
it is connected to an AC outlet and the back of
the unit.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
2
The unit is not turned on : rotate the VOLUME
knob from the OFF position.
Turntable
CAUTION:
No sound is coming from unit.
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER - SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
1
2
The white protective needle cover was not
removed.
The volume is not turned unit.
The lighting flash with arrowhead symbol, within an equilateral
triangle, is intended to alert user to the presence of uninsulated
"dangerous voltage" within the product's enclosure that may be
of sufficient magnitude to constitute risk of electric shock to
persons.
Tone arm will not move.
1
2
Block tie-wrap was not removed from underneath
tone arm.
Tone arm hold down clip was not released.
The exclamation point within an equilateral triangle is intended
to alert user to the presence of important operating and
maintenance (servicing) instruction in the literature accompanying
the appliance.
Needles are available for addititonal charges, please
call us at 1-800-926-7801 for assistance
SPECIFICATION
Power Supply
Power Consumption
Speed
Speaker
Replacement Needle
: AC adapter -(DC 12V 0.5A)(Included)
: 12W
: 331/
3
/ 45 /78 RPM
: 3 x 5” Dynamic Type x 2
: NP4
•DESIGN AND SPECIFICATION SUBJECT TO CHANGE WITHOUT NOTICE.
910-264500-0010-100
7
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Control Locators
Unpacking
Power Source
Unit Controls
1
Remove packing materials from unit.
Note: Save all packing materials.
1. Tone Arm
2. Cue lever
3. Power light indicator
4. Speed control switch
5. Security Hook
1
1
2
Untie the wire on the AC ADAPTER (16).
Plug the AC ADAPTER into appropriate wall
outlet.
2
2
3
4
5
Remove plastic bag covering radio.
Remove AC ADAPTER from packing.
Remove tie from A/C ADAPTER.
3
3
Plug the small end of the adapter into the
ADAPTER JACK (12) on the back of the unit.
6. Tone Control
4
7. ON/OFF Volume Knob
8. Tone Arm Rest
9. Turntable
10. Adapter for 45 RPM records
11. Speaker
12. Adapter Jack
13. Aux In Jack
14. Aux In Phono on/off
15. USB Jack
16. AC Adapter
5
Open lid and remove styrofoam shipping
material from turntable.
9
8
6
7
6
7
Remove black tie-wrap from under the tone
arm.
Remove white protective needle cover by gently
pulling towards the front of the unit.
10
(placed in a white cardboard box inside
the styrofoam packaging)
13 15
11
11
8
9
Turn the TURNTABLE SUSPENSION SCREW
(31) clockwise until it is all the way down.Do
not force or over tighten it. This allows the
turntable to float on its shock absorbers.
12 14
16
Release tone arm hold down clip by gently
pushing to the right. This will unlock tone arm
from its arm rest. Re-lock the hold down clip
when moving the unit to another location.
5
4
Download from Www.Somanuals.com. All Manuals Search And Download.
|