U S E R G U I D E
UGG011/0504
CHS Tangential Feed
Granulators
Models CHS-810, CHS-814, CHS-819, and CHS-824
WARNING - Reliance on this Manual Could Result in Severe Bodily Injury or Death!
This manual is out-of-date and is provided only for its technical information, data and capacities. Portions of this manual
detailing procedures or precautions in the operation, inspection, maintenance and repair of the product forming the subject
matter of this manual may be inadequate, inaccurate, and/or incomplete and cannot be used, followed, or relied upon.
Contact Conair at [email protected] or 1-800-654-6661 for more current information, warnings, and materials about
more recent product manuals containing warnings, information, precautions, and procedures that may be more adequate
than those contained in this out-of-date manual.
Corporate Office: 412.312.6000
l
Instant Access 24/7 (Parts and Service): 800.458.1960
l
Parts and Service: 814.437.6861
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
1. Introduction
Purpose of the User Guide .................................................................1-2
How the Guide is Organized ..............................................................1-2
Your Responsibilities as a User ..........................................................1-2
ATTENTION: Read This so no One Gets Hurt ......................................1-3
2. Technical Specification
Dimensions, Data, Sound Level .........................................................2-2
3. Function Description
General .............................................................................................3-2
Safety System ...................................................................................3-4
4. Safety Instructions
Safety Instructions .............................................................................4-2
5. Installation
Pre-start checks .............................................................................. 5-2
Two hours after first start ........................................................... 5-2
Electrical connection .........................................................................5-3
Opening of hopper, screen box and granule bin ..............................5-4
Closing the screen box, granule bin and hopper ...............................5-5
6. Operation and Daily Maintenance
Starting and Stopping ...................................................................... 6-2
Inspection ........................................................................................ 6-3
Daily Inspection ........................................................................ 6-3
Weekly Inspection ...................................................................... 6-3
Monthly Inspection ....................................................................6-3
Cleaning .......................................................................................... 6-4
Fault-finding, If the Granulator Does Not Start ................................ 6-6
Table of Contents
l
i
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Service
Changing the knives ........................................................................7-2
Removing the knives ................................................................ 7-2
Installing the knives .................................................................. 7-3
Sharpening the knives .................................................................... 7-6
Granulator with Open Cutter ...................................................... 7-6
Transmission .................................................................................. 7-8
Inspection and Adjustment of Drive Belts . . . . . . . . . . . . . . . . . 7-8
Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-10
Cutter and Motor Pulleys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-11
Removal/Installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-11
8. Spare Parts List
Cutting Chamber................................................................................8-3
Staggered Rotor ................................................................................8-4
Open Rotor ........................................................................................8-5
Knives ..............................................................................................8-6
Knives, Open Rotor ............................................................................8-6
Transmission ....................................................................................8-7
Screen ..............................................................................................8-8
Screen Box........................................................................................8-8
Outfeed, Granule Bin Manual ............................................................8-9
Vaccum Suction/Blower F-7/F-5......................................................8-10
Hopper ............................................................................................8-11
Hopper - Noise encapsulated machine with extraction fan ..............8-12
Hopper Device ................................................................................8-13
Sound Cabin....................................................................................8-14
Enclosure/Body................................................................................8-15
Safety..............................................................................................8-16
9. Wiring Diagram
Wiring Diagram ..................................................................................9-2
Current sensing relay..........................................................................9-3
Connection..........................................................................................9-4
Example ..........................................................................................9-5
ii
l
Table of Contents
Download from Www.Somanuals.com. All Manuals Search And Download.
10. Layout
CHS Series, Allround Hopper Noise Encapsulated,
Hopper Loader, Non Soundproof . . . . . . . . . . . . . . . . . . . . . . . . . 10-2
CHS Series, Allround Hopper Noise Encapsulated, Blower F-7 Cyclone
AX-7,5 with Holder/Bag Holder, Soundproof . . . . . . . . . . . . . . . . 10-2
CHS Series, Allround Hopper Noise Encapsulated with Conveyor, Band
Conveyor, Hopper Loader, Non Soundproof . . . . . . . . . . . . . . . . . 10-3
CHS Series, Allround Hopper Noise Encapsulated with Conveyor, Band
Conveyor, Blower F-7, Cyclone AX-7,5, Soundproof . . . . . . . . . . . 10-3
11. Accessories, Overview
Ordering Spare Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-2
Pre-setting of Rotating Knives, Granulator with Open Cutter . . . . 11-3
Setting up the Knives . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-3
Installing of Pre-set Knives . . . . . . . . . . . . . . . . . . . . . . . . 11-3
Third Fixed Knife, Removal, Installation . . . . . . . . . . . . . . . . . . . . 11-5
Band Conveyor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-6
Spare Parts List for the Band Conveyor . . . . . . . . . . . . . . . 11-8
12. Transport and Storage
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-2
Unpacking and Checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-2
Lifting and Transport to Place of Use . . . . . . . . . . . . . . . . . . . . . . . 12-2
Positioning in Place of Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-2
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-3
Long-Term Storage/Conservation . . . . . . . . . . . . . . . . . . . . . . . . . 12-3
A. Customer Service
We’re Here to Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-1
How to Contact Customer Service . . . . . . . . . . . . . . . . . . . . . . . . .A-1
Before You Call... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-1
Equipment Guarantee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-2
Performance Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
Warranty Limitations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-2
Table of Contents
l
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
iv
l
Table of Contents
Download from Www.Somanuals.com. All Manuals Search And Download.
S E C T I O N
1
Introduction
Purpose of the User Guide . . . . . . . . . . . . . 1-2
How the Guide is Organized . . . . . . . . . . . . 1-2
Your Responsibilities as a User . . . . . . . . . . 1-2
ATTENTION:
Read this so no one gets hurt . . . . . . . . 1-3
Introduction
l
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Purpose of the User Guide
This User Guide describes the Conair CHS Tangential Feed Granulators.
It explains step-by-step how to install, operate, maintain and repair this
equipment.
Before installing this product, please take a few moments to read the
User Guide and review the diagrams and safety information in the
instruction packet. You also should review manuals covering associated
equipment in your system. This review won’t take long, and it could save
you valuable installation and operating time later.
How the Guide is Organized
Symbols have been used to help organize the User Guide and call your
attention to important information regarding safe installation and operation.
Symbols within triangles warn of conditions that could be hazardous to users or
could damage equipment. Read and take precautions before proceeding.
1
Numbers indicate tasks or steps to be performed by the user.
A diamond indicates the equipment’s response to an action performed by the user.
An open box marks items in a checklist.
N
❒
A circle marks items in a list.
•
✒
Indicates a tip. A tip is used to provide you with a suggestion that will help you with
the maintenance and operation of this equipment.
✐
Indicates a note. A note is used to provide additional information about the steps
you are following throughout this manual.
Your Responsibility as a User
You must be familiar with all safety procedures concerning installa-
tion, operation and maintenance of this equipment. Responsible safety
procedures include:
• Thorough review of this User Guide, paying particular attention
• tTohhoarozaurgdhwreavrineiwngos,f athpepeenqduiicpems eanntditrseellaft,ewd idthiagcararemfus.l attention
• tTohvooroltuagghe rseovuirecweso, finintesntrduecdtiuosnemananduwalasrnfoinrgaslasboeclisa.ted equipment.
• Step-by-step adherence to instructions outlined in this User Guide.
1-2
l
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
ATTENTION:
Read This so no One Gets Hurt
We design equipment with the user’s safety in mind. You can avoid the potential
hazards identified on this machine by following the procedures outlined below and
elsewhere in the User Guide.
WARNING: Improper installation, operation or
servicing may result in equipment damage or
personal injury.
This equipment should be installed, adjusted, and serviced by qualified
technical personnel who are familiar with the construction, operation
and potential hazards of this type of machine.
All wiring, disconnects and fuses should be installed by qualified elec-
trical technicians in accordance with electrical codes in your region.
Always maintain a safe ground. Do not operate the equipment at power
levels other than what is specified on the the machine serial tag and
data plate.
WARNING: Voltage hazard
This equipment is powered by three-phase alternating current,
as specified on the machine serial tag and data plate.
A properly sized conductive ground wire from the incoming power
supply must be connected to the chassis ground terminal inside the
electrical enclosure. Improper grounding can result in severe personal
injury and erratic machine operation.
Always disconnect and lock out the incoming main power source before
opening the electrical enclosure or performing non-standard operating
procedures, such as routine maintenance. Only qualified personnel
should perform troubleshooting procedures that require access to the
electrical enclosure while power is on.
Introduction
l
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
This manual applies to the CHS series of Conair granulators.
Model nos. CHS-810, CHS-814, CHS-819, and CHS-824 specify the size of the
cutting chamber.
Supplementary designations specify:
Read the Manual before installing and using the machine.
Be careful when the knives are accessible, they are sharp, and
can cause personal injury!
•
•
•
•
These Conair granulators are designed for granulating injection
molded, blow molded and extruded plastic parts and scrap.
The size and performance of the granulators are designed to suit
the type of waste material.
Approval must be obtained from Conair for granulating other
products and materials for the warranty conditions to apply.
The granulators are designed so that maintenance and cleaning can
be done quickly and easily, both routine maintenance and changing
of materials.
•
•
•
•
•
•
All service must be done by trained service personnel.
This Manual contains instruction for both handling and service.
Chapter 7 contains instructions directed towards service personnel.
Chapter 11 contains accessory equipment for the machine.
Other Sections contain instructions for the operator.
The granulators are delivered with an Instruction Manual and
touch-up paint.
•
•
Any modifications or conversions of the machines must be
approved by Conair. This is to prevent injuries. The machine
warranty and product assurance would otherwise be rendered void.
Please address any queries to the local Conair representative or
Conair customer service.
1-4
l
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
S E C T I O N
2
Technical Specifications
Specifications of a CHS Granulator . . . . . . . 2-2
Technical Specifications
l
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Batch Feed Granulators CHS-810, CHS-814, CHS-819 and CHS-824
G
MODELS
CHS-810
CHS-814
CHS-819
CHS-824
Performance characteristics
Throughput* lb/hr {kg/hr}
Cutter chamber opening in. {mm}
H
200 {90}
8.7 x 9.5
{220 x 240}
356
250 {115}
8.7 x 14.2
{220 x 360}
356
330 {150}
8.7 x 18.9
{220 x 480}
356
400 {180}
8.7 x 23.6
{220 x 600}
356
Rotor speed rpm
Cutting Circle in. {mm}
Standard motor power Hp
Drive type
7.88 {200}
5
7.88 {200}
7.5
7.88 {200}
10
7.88 {200}
10
belt drive
Hopper type
hand, robot, conveyor - standard (sheet, roll, profile, side feed - optional)
Vacuum discharge side
Screen mesh sizes
Rotor type
rear
3
5
3
1
5
1
in. {4, 5, 6, 8, 10, 12 mm}
/32, /16, /4, /16, /8, /2
staggered rotor - open rotor optional (except for CHS-824)
Knives
Number of rotating knives
Number of bed knives
Dimensions inches {mm}
A - Height - hopper closed
B - Height - hopper open
C - Width
3 X 2
2
3 X 3
2
3 X 4
2
3 X 5
2
C
57 {1450}
72 {1830}
57 {1450}
72 {1830}
57 {1450}
72 {1830}
57 {1450}
72 {1830}
26.75 {680}
35.5 {900}
54.75 {1390}
45 {1145}
31.50 {800}
35.5 {900}
54.75 {1390}
45 {1145}
36.25 {920}
35.5 {900}
54.75 {1390}
45 {1145}
41 {1040}
D - Base depth
35.5 {900}
54.75 {1390}
45 {1145}
E - Overall depth
F - Infeed height
G - Feed hopper opening - width
H - Feed hopper opening - height
Weight lb {kg}
9.44 {240}
10.25 {200}
14.13 {360}
10.25 {200}
18.86 {480}
10.25 {200}
23.63 {600}
10.25 {200}
B
A
Installed
750 {340}
882 {400}
794 {360}
926 {420}
1014 {460}
1169 {530}
1279 {580}
1477 {670}
Shipping
F
Voltages Total amps based on standard motor
208V/3 phase/60 Hz
20
18
9
24
22
11
9
31
28
14
11
31
28
14
11
230V/3 phase/60 Hz
460V/3 phase/60 Hz
575V/3 phase/60 Hz
7
†
D
Noise level
With integral soundproofing
80-85 dbA
E
SPECIFICATION NOTES:
3
*
Throughput is based on a /8 inch {9.53 mm} screen. Throughput rates are provided as a capacity guideline only.
Throughput will vary according to size, shape, thickness and properties of the material to be cut, as well as the
desired size of the granulate. Consult Conair for a material test or help determining the correct granulator model for
your application.
† Noise level will vary according to material type being processed and the granulator configuration. These ranges are
based on tests using SPI standards.
STANDARD STAGGERED ROTOR
with disposable, cassette knives
Specifications may change without notice. Check with a Conair representative for the most current information.
OPTIONS
MOTOR OPTIONS ꢀ=standard o=optional
•
Discharge: manual, vacuum
(standard), blower
CHS-810 CHS-814 CHS-819 CHS-824
5 Hp
ꢀ
o
N/A
ꢀ
N/A
o
N/A
o
•
•
•
•
Hardened cutter housing
Third bed knife
3-blade open rotor
7.5 Hp
10 Hp
15 Hp
o
o
ꢀ
ꢀ
OPTIONAL OPEN ROTOR
with scissor-cutting, slant knives
o
o
o
o
High RPM (512 RPM) motor
TPGS019/0603
2-2
l
Technical Specifications
Download from Www.Somanuals.com. All Manuals Search And Download.
S E C T I O N
3
Function Description
General . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Safety System . . . . . . . . . . . . . . . . . . . . . 3-4
Function Description
l
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Function Description
General
The granulator is designed for grinding plastic waste to
H
for recycling.
The plastic waste should be free from metal parts
and contamination before granulating.
The granulator is controlled by
start/stop controls on a control
A
panel.
G
C
Standard cutter
F
D
B
E
B
C
Open cutter
The plastics waste is feed into the hopper (A) and falls down into the cutter hous-
ing, where rotating knives (B) cut the plastics waste against fixed knives (C) to
granulate.
A perforated screen (D) determines the size of the granulate. The screen is located
in the lower section of the cutting chamber and can easily be changed to give the
desired granulate size.
The granulate passes the screen and falls down through the outlet chute/granule bin
(E) to the outlet pipe (F) for onwards transport.
Granulators with an extraction fan are equipped with an extraction blower (G)
which sucks the granulate out to a cyclone (H) for separation of air. On granulator
3-2
l
Function Description
Download from Www.Somanuals.com. All Manuals Search And Download.
models with a conveyor, the hopper is equipped with a conveyor belt. The
conveyor can be equipped with a metal detector.
After this, the granulate is ready for re-use in the production machine, or to be
transported to a container for later use.
The granulator is easy to clean, with a folding hopper and also good accessibility
for maintenance. Knives on the staggered rotor are disposable and should be
replaced when necessary. The rotating knives on an open rotor can be re-sharp-
ened. Grinding is done in a special grinding jig. (The jig is not included when the
granulator is delivered, but is a very practical accessory.)
Function Description
l
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety System
The granulator has a safety system to prevent access to dangerous
components during operation.
The granulator has knives that rotate at high speed. The granulator is
therefore equipped with a safety system to avoid personal
injury.The safety system must not be changed or modified
under any circumstances.
If the safety system of the granulator is changed or
Breaking key
modified, the machine can be dangerous to use,
presenting a serious risk of personal injury.
All care and maintenance to the safety system of the
granulator must be carried out by personnel with the
necessary knowledge.
If the safety system of the granulator is modified in any way,
Conair’s responsibility under the Machinery Directive ceases
to apply.
Emergency
stop
Safety
switches
Only Conair spare parts must be used to replace safety
components.
Emergency Stop
The granulator has an emergency stop on the control panel.
It can also be equipped with extra emergency stops.
The emergency stop is activated by pressing the button. Reset
by turning the button in the direction of the arrow (counter-
clockwise).
Safety Switch
The granulator has safety switches of the
position switch type with breaking key:
Main switch
–
If a secured position is changed or when a breaking key
is undone,
it will break the current and the granulator stops.
This granulator has 2 safety switches:
1 at the hopper and 1 at the screen box
Check the wiring diagram (Section 9) to see how many safety switches the granulator is
equipped with.
3-4
l
Function Description
Download from Www.Somanuals.com. All Manuals Search And Download.
Star Knob
The star knob for the hopper and screen box
is a very important component in the safety
system of the granulator.
It should take such a long time for the knob/screw
to be undone, that the cutter has stopped before the
granulator can be opened.
✐
NOTE: The length of the screw must never be
changed.
✐
NOTE: The screw can not be removed.
The screen is hardened and the knob is permanently attached.
–
✐
To change a star knob, please contact Conair.
NOTE: If the star knob is modified in any way,
Conair’s responsibility under the Machinery Directive
ceases to apply.
Before Starting:
The star knobs on the hopper and screen box
must be fully tightened to stop.
The granulate bin should be installed and the door
shut and locked.
Function Description
l
3-5
Download from Www.Somanuals.com. All Manuals Search And Download.
3-6 l Function Description
Download from Www.Somanuals.com. All Manuals Search And Download.
S E C T I O N
4
Safety Instructions
Safety Instructions . . . . . . . . . . . . . . . . . . 4-2
Safety Instructions
l
4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions
Conair granulators are designed for granulating injection moulded, blow moulded
and extruded plastic waste.
The specific technical data for this machine, concerning power and perfor-mance
etc. is described in detail in Section 2.
The granulator is equipped with safety switches, which are described in
Section 3.2.
Follow the instructions in this manual to avoid personal injury and damage
to machine components.
Always follow these safety measures when handling the granulator.
•
Electrical installation must only be done by a competent
electrician!
•
Before the granulator is opened for servicing and maintenance.
Always disconnect the power with both the main switch and
the switch on the granulator.
•
•
Never put any part of your body through the granulator open-
ings, unless both the main switch and the switch on the granu-
lator are in “Off” (0) position.
Be careful with the knives, they are sharp and can cause per-
sonal injury.
•
•
If the rotor must be turned manually – do this with great care!
Observe care when opening or closing the hopper and screen-
box, so as not to trap parts of the body.
•
•
•
•
The granulator should not be able to start before the hopper
and screen box are properly closed.
Never remove protective guards or pipes adjacent to the out-
let/granule bin.
Granulators with belt conveyors! Observe care so that convey-
or belts with dogs do not grip clothing, or arms and feet.
During maintenance, pull out the plug on the distribution box.
4-2
l
Safety Instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
DANGER! High voltage!
This sign is on the door to the distribution box and the con-
nection boxes.
DANGER! Cutting or pinch risk!
This sign is placed where there is a risk of being cut or
pinched.
DANGER! Be careful!
This sign is located by all danger areas, where care and
extra attention is required.
Safety Instructions
l
4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
4-4
l
Safety Instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
S E C T I O N
5
Installation
Pre-start checks . . . . . . . . . . . . . . . . . . . . . 5-2
Two hours after first start . . . . . . . . . . . . 5-2
Electrical connection . . . . . . . . . . . . . . . . . . . 5-3
Opening of hopper, screen box and granule bin 5-4
Closing the screen box, granule bin and hopper 5-5
Installation
l
5-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Read through the whole of Section 5 before installing the machine! All instructions
must be followed in the given order to avoid injury or damage.
Be careful with the knives, they are sharp and can cause personal injury.
The granulator must only be connected to the mains by a competent
electrician.
Pre-Start Checks
•
The unpainted parts of the machine are protected with oil prior to delivery
and transport Clean the granulator from rust protection agent before it is
used.
•
Check the knife clearance and tightening torque on the bolts for the
knives. Refer to installation of knives in Section 7.
Two Hours After First Start
Check the knife clearance again and the tightening torque of the knife retentio
screws. Check the screws for both the fixed and rotating knives.
5-2
l
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Connection
The granulator should be connected by a competent electrician.
•
Connect the granulator to the main power supply. The wiring diagram
indicates the fuse sizes, see Section 9.
•
The granulator is delivered with electrical equipment connected for clock-
wise phase rotation. Check with a phase sequence indicator and connect
the granulator with clockwise phase rotation.
Check the direction of rotation of the granulator motor:
•
Make sure that the main switch beneath the control panel is “On” (1).
•
Check that the emergency stop is not activated.
•
Check that the star knobs on the hopper and screen box locks are fully
tightened to stop.
•
•
Undo and remove the upper panel on the right hand side of the granulator.
Press “Start”
•
Check that the granulator motor rotates in the direction indicated by the
arrow on the cutter pulley.
•
Granulator with blower, – check that the direction of rotation of the blower
corresponds with the arrow on the cover.
✐
NOTE: The blower blows even if the direction of rotation is wrong.
•
Granulator with conveyor belt, – check the direction of the
conveyor belt.
If any direction of rotation should be incorrect:
•
•
•
Press the stop button.
Switch off the main switch.
Switch two incoming phases.
Installation
l
5-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Opening of Hopper, Screen Box and
Granule Bin
Before opening the hopper, granule bin and
screen box, switch both the main switch and
granulator switch “Off”.
Be careful when the knives are accessible.
They are sharp and can cause personal injury.
A
Opening the hopper
1 Check that the hopper is empty, then stop
the granulator.
B
2 Undo the star knobs (A) on the hopper.
3 Undo the tip catch (B).
✐
NOTE: The hopper is counter-balanced with one
alternative two gas springs, but hold the hopper
at the same time, so that it does not fall down
out of control.
4 Open/fold the hopper backwards.
Opening the screen box
1 Open the door (C).
2 Undo and pull out the extraction pipe
from the rear of the granulator.
Alt. CHS with extraction fan, undo
the quick coupling on the outlet
G
F
C
pipe stub.
E
3 Remove the granule bin (E).
4 Undo the star knobs (F) for the screen box (G)
✐
NOTE: Hold the screen box at the same time, so that it does not fall down out of control.
5 Fold the screen box down.
The screen is now accessible
and can be lifted out for
changing or cleaning.
5-4
l
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Closing the Screen Box, Granule Bin and Hopper
✐
NOTE: Before closing, make sure that the mating
surfaces are clean!
There is a pinch risk during closing, be careful.
Close the screen box and install the granule bin
1
Make sure that the screen is correctly
positioned in the screen box.
Lift the screen box up and tighten the
star knobs properly to stop.
2
3
4
Install the granule bin.
Install the extraction pipe.
Alt. CF machine with extraction fan, do up the quick
coupling (D) on the outlet pipe stub.
Close the door.
D
5
Close the hopper
1
Check and make sure that
no granulate lies on the
mating surfaces or flanges.
Shut/fold back the hopper.
2
3
Open and make sure that the
tipping catch falls into the cutout.
Lock the hopper with the star knobs, tighten
the star knobs properly to stop.
Switch the main switch “On”.
Start the granulator.
4
5
6
Installation
l
5-5
Download from Www.Somanuals.com. All Manuals Search And Download.
5-6
l
Maintenance
Download from Www.Somanuals.com. All Manuals Search And Download.
S E C T I O N
6
Operation and Daily Maintenance
Starting and Stoping . . . . . . . . . . . . . . . . . 6-2
Inspection . . . . . . . . . . . . . . . . . . . . . . . 6-3
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . 6-4
Fault-Finding . . . . . . . . . . . . . . . . . . . . . 6-6
Operation and Daily Maintenance
l
6-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation and Daily Maintenance
Starting and Stopping
The main switch is located beneath the control panel on the front
of the granulator.
Starting and stopping is controlled by push buttons on the control panel.
✐
NOTE: Never stop the granulator before all material in
the hopper and cutter housing is completely granulated.
Residual material will clog the rotor in the granulator during re-start.
The motor will be overloaded and the overloading protection will
trigger.
Start Emergency
stop
Stop
Main switch
6-2 l Operation and Daily Maintenance
Download from Www.Somanuals.com. All Manuals Search And Download.
Inspection
There must be no plastic material left in the granulator when
inspection is carried out.
CAUTION: All servicing must be done by trained personnel in order to avoid personal
injury and damage to the machine.
Daily Inspection
Flaps in the hopper. Check that the flaps are undamaged. Replace dam-
aged flaps at once. Damaged flaps can drop down into the cutter housing
and damage the knives. Damaged flaps also entail the risk of material
ejection.
Emergency stop. Check the emergency stop function. Start the granulator
and stop it with the emergency stop(s).
Reset. Turn the stop button in the direction of the arrow (counterclock-
wise).
Weekly Inspection
Cables. Check the electric cables of the machine for wear or other dam-
age. Replace damaged cables at once.
Safety switches. Check the safety switch functions.
This granulator has 2 safety switches:
1
1
at the hopper
at the screen box
Check the hopper´s safety switch.
Undo the star knobs on the hopper, and try to start the granulator.
The granulator should not be possible to start before the hopper has been
closed and the star knobs are properly tightened to stop.
Check the screen box safety switch.
Undo the star knobs on the screen box and try to start the granulator.
The granulator should not be possible to start before the screen box has
been closed and the star knobs are properly tightened to stop.
✐
NOTE: The granule bin should be installed, and the door closed and locked.
Monthly Inspection
Check that the V-belts are undamaged.
Check the V-belt tension every 6 months, see Section 7.8 “Transmission”.
Operation and Daily Maintenance
l
6-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning
Clean at color change, monthly or at least once/300 hours.
Be careful when the hopper have been opened. The knives are now
accessible, they are sharp, and can cause personal injury.
1
Check that the hopper is empty, then stop the granulator.
Switch “Off” both the main switch and the switch on the granulator.
2
3
✐
Clean the outside of the hopper.
Undo the star knobs on the hopper.
Undo the tip chatch.
4
NOTE! The hopper is counterbalanced with one alter-
native two gas springs, but hold the hopper at the same
time, so that it does not fall down out of control.
5
6
7
8
9
Open/fold the hopper backwards.
Clean the hopper´s opening.
Lift out and clean the inner and outer flaps.
Open the door.
Undo and pull out the extraction
pipe from the rear of the granulator.
Alt. machine with extraction fan,
undo the quick coupling on the
outlet pipe stub.
10 Remove the granule bin.
11 Undo the star knobs for the screen box.
✐
NOTE! Hold the screen box at the same time,
so that it does not fall down out of control.
12 Fold the screen box down.
A
13 Undo and clean the screen.
14 Undo and remove the blue screws (A)
for the bearing cleaning holes.
15 Blow through the holes with compressed
air and rotate the cutter at least one turn.
✐
NOTE: When the cutter is rotated
manually, do this with great care.
The knives are sharp and can cause
personal injury.
6-4 l Operation and Daily Maintenance
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning (continued)
✐
NOTE: Use protective goggles and make sure that no
material blows into the safety switches!
16 Clean the granule bin and the screen box.
17 Clean the cutter housing inside and outside.
18 Clean any transport pipes, blower and cyclone.
Re-install after cleaning
1
2
3
4
5
Install the blue screws.
Install the screen in the screen box.
Lift up the screen box and and tighten the star knobs to stop.
Install the granule bin.
Install the extraction pipe.
Alt. CHS series-machine with extraction fan, do up the quick
coupling on the outlet pipe stub.
6
7
Close the door.
Close the hopper. Check and make sure that no granulate remains .
on the mating flanges or surfaces.
8
9
Open and make sure that the tipping catch falls into the cutout.
Lock the hopper with the star knobs, tighten the knobs
properly to stop.
Operation and Daily Maintenance
l
6-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Fault-Finding
The granulator does not start
•
•
•
Check that the emergency stop is not activated.
Reset by turning the button(s) in the direction of the arrow
(counterclockwise).
Check that the hopper is properly closed.
The granulator will not start if the hopper not is properly closed.
Tighten the star knobs properly to stop.
Check that the screen box is properly
closed.
The granulator will not start, if the screen
A
box not is properly closed.
Tighten the star knobs properly to stop.
Check the overload circuit breaker
B
•
for the motor.
The motor has an overload circuit
breaker, F1, in the distribution box, which
trips if you jam or over-load the motor.
This is indicated in the window (A) which shows “0”.
Reset, press the “Reset” button (B).
Check that there is no material left in the granulator before restarting.
Granulator with blower (CHS series-machine with extraction fan).
Check the blower overload circuit breaker. The granulator will not start
if the blower does not start.The blower motor has an overload circuit
breaker, F2, in the distribution box, which trips if you jam or overload
the blower.This is indicated in the window (A) which shows “0”.
Reset, press the “Reset” button (B).Check that there is no material left
in the granulator before restarting.
•
6-6 l Operation and Daily Maintenance
Download from Www.Somanuals.com. All Manuals Search And Download.
•
Granulator with conveyor belt, if the conveyor belt does not start –
check the conveyor belt overload circuit breaker.
The conveyor belt motor has an overload circuit breaker, F3, in
the distribution box, which trips if you jam or overload the
conveyor belt.
This is indicated in the window (A) which shows “0”.
Reset, press the “Reset” button (B).
Check that there is no material left on the band before re-starting.
Check the granulator knives and knife tolerance.
If the granulator knives are blunt and unsharpened, or if the knife
clearance is incorrect, this can result in stoppage. The granulator
motor overload circuit breaker will trip. Check the knives.
Sharpen or replace the knives, or adjust the knife clearance, see
next Section.
•
Check also the wiring diagram in Section 9; supplements and deviations
may be applicable.
Operation and Daily Maintenance
l
6-7
Download from Www.Somanuals.com. All Manuals Search And Download.
6-8 l Operation and daily maintenance
Download from Www.Somanuals.com. All Manuals Search And Download.
S E C T I O N
7
Service
Changing the Knives . . . . . . . . . . . . . . . . . 7-2
Removing the knives . . . . . . . . . . . . . . . . . 7-2
Installing the Knives . . . . . . . . . . . . . . . . . 7-3
Sharpening Knives -
Granulators with Open Cutter . . . . . . . . 7-6
Transmission . . . . . . . . . . . . . . . . . . . . . . 7-8
V Belts, Inspection, and Adjustment . . . . . . . 7-8
Lubrication . . . . . . . . . . . . . . . . . . . . . . 7-10
Cutter Pulley/Motor Pulley . . . . . . . . . . . . 7-11
Service
l
7-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
All service must be carried out by trained personnel in order to avoid personal
injury or damage to the machine.
Changing the knives
Removing the knives
Check the screen for wear when the knives are changed. Change the screen when
the holes begin to be pear shaped.
Be careful when handling the knives, they
are sharp and can cause personal injury.
Use protective gloves!
Each time the knives are changed, the knife
fastening screws must be replaced by new
ones.
Changing the knives.
A, B
Open the hopper and any door. Remove the granule bin, then fold the screen box
down and lift it out – see Section 5.3.
Removing the rotating knives.
1
Remove the screws (A) and washers (B),
2 each per knife. The knives are now loose.
Lift out the rotating knives.
Clean the surfaces where the knives were
located.
2
3
Removing the fixed knives.
4
Undo the socket cap screws (C) on the
front knife support rule (D).
✐
NOTE: Hold the fixed knife and support
rule before removing the last screw.
5
Lift out the fixed knife together with the
support rule.
6
7
Clean the knife location.
Put the support rule back loosely.
E
F
D
C
7-2
l
Service
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Undo and remove the socket cap screws (E) on the rear knife
support rule (F).
✐
NOTE: Hold the fixed knife and support rule before removing the last screw.
9
Lift out the fixed knife together with the support rule.
10 Clean the knife location.
11 Put the support rule back loosely.
Installing the Knives
The knife attachments for both the fixed and rotating knives must be carefully
cleaned.
First install the rear, fixed knife
1
Install the rear fixed knife on the knife
attachment.
2
Screw in the socket cap screws (E), so
that the support rule (F) lightly supports
the knife.
3
Press the knife firmly into the knife
attachment to bed it down.
✐
NOTE: The screws in the rear of the
knife attachment are bonded in place.
✐
NOTE: The knife has a fixed position
and no adjustment may be done.
4
Tighten screws (E), with alternating
tightening torque to 29.5lb-ft (40 Nm).
E
F
Install the rotating knives.
✐
NOTE: When the rotating knives are installed in a granulator with open cutter, the knives must
always be pre-set before installation!
Pre-setting of knives for a granulator with open cutter is best done in a special pre-
setting jig. The jig is not included when the machine is delivered, but is a very
practical accessory which can be ordered. The jig and knife pre-setting is described
in Section 11.
Service
l
7-3
Download from Www.Somanuals.com. All Manuals Search And Download.
5
6
Install one rotating knife at a time
on the knife attachment on the rotor.
Install screws (A) with washers (B),
and tighten so that they hold
the knife lightly.
7
✐
Press the knife firmly into the knife
attachment.
NOTE: The screws in the rear of the
A, B
knife attachment are bonded in place.
✐
NOTE: The knife has a fixed position and no adjustment may be done.
8
Tighten screws (A), with alternating tightening torque to 55.3 lb-ft (75 Nm).
✐
NOTE: Granulators with open cutter – tighten the screws (A) with alternating
increased torque to 162.3 lb-ft (220 Nm).
9
Check that the rotating knife can pass the rear fixed knife freely.
If the knife can not pass freely – undo screws (A) and press the rotating
knife firmly into the knife attachment.
Undo screws (E) and press the fixed knife firmly into the knife attachment.
10 Check the knife clearance with a feeler gauge. The clearance should be
0.008 - 0.012 in. (0.20 - 0.30 mm), check at the outer edges of the knives.
11 Install all the rotating knives.
12 Press the knife firmly into the knife attachment.
13 Tighten the screws (A) with alternating increased torque to
55.3 lb-ft (75 Nm).
✐
NOTE: Granulators with open cutter – tighten the screws (A) with alter-nating
increased torque to 162.3 lb-ft (220 Nm).
14 Check that each rotating knife can pass the rear fixed knife freely.
If any rotating knife can not pass freely – undo the screws (A) and press the
knife firmly into the knife attachment.
15 Check the clearance of each rotating knife with a feeler gauge The clearance
should be 0.008 - 0.012 in. (0.20 - 0.30 mm), check at the outer edges of the
knives.
7-4
l
Service
Download from Www.Somanuals.com. All Manuals Search And Download.
Then install the front, fixed knife
16 Install the knife in the knife attachment.
17 Screw in the socket cap screws (C) and
tighten so that the support rule (D) lightly
supports the knife.
18 Press the knife firmly into the knife
attachment.
✐
NOTE: The screws in the rear of the
knife attachment are bonded in place.
✐
NOTE: The knife has a fixed position
and no adjustment may be done.
19 Tighten the screws (C), with alternating
tightening torque to 29.5 lb-ft (40 Nm).
20 Carefully check that all rotating knives
can pass the front fixed knife.
D
C
If any knife can not pass the front fixed knife freely
– undo the screws (C) and press the knife firmly into the knife
attachment.
21 Check the clearance of each rotating knife with a feeler gauge The
clearance should be 0.008 - 0.012 in. (0.20 - 0.30 mm), check at
the outer edges of the knives.
22 Re-check the tightening torque of all rotating knives (55.3 lb-ft
[75 Nm]; granulator with open cutter 162.3 lb-ft [220 Nm]).
23 Re-check the tightening torque of the front and rear fixed knives
(29.5 lb-ft [40 Nm]).
Service
l
7-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Sharpening Knives
✐
NOTE: Only rotating knives for granulators with an open rotor can be sharpened. Other knives
are disposable and are replaced when necessary.
Sharpening Knives - Granulators with Open Cutter
Keep the complete set of knives together as one unit.
✐
NOTE: To avoid unbalance, all the knives belonging to the cutter must be ground exactly the
same.
Be careful when handling the knives, they are sharp and can cause
personal injury.
✐
NOTE: Get an experienced craftsman to sharpen the knives.
Only sharpen the marked surfaces and respect the given dimensions!
The knives must be sharpened exactly, to get the correct cutting and relief angles.
Otherwise the efficiency of the granulator will be impaired.
The knife must be cooled during sharpening. The knives must not be burned or
blued under any circumstances, otherwise they will loose their hardness and dura-
bility.
If the knife is blued or burned, they can not be repaired by grinding down the blued
or burned area. The hardened knife is then completely spoiled and has lost all its
hardness and durability.
Use the Conair grinding jig SF-20 (accessory, art no. 3-030324) and a surface
grinder with magnetic table. The jig gives exact correct cutting and relief angles.
•
•
•
Remove the knives adjustment screws.
Grind the worst knife to make the relief angle 35°.
Tighten the knife in the right-hand position in the
jig, using spacer “A” beneath the rear of the knife
(see illustration).
Grind
Spherical washers should be used when tightening
the knife.
•
•
Grind until all the irregularities on the knife edge
have disappeared.
Retain the settings of the surface grinder and grind
all the other knives exactly the same.
A
Grind
7-6
l
Service
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
•
Grind the cutting angle of the knives to 30°
Remove spacer “A” beneath the knife.
Tighten the knife and grind until the cutting
edge is 0.118 in. (3 mm) wide.
o
35
o
30
Min. 2.205 in. (56 mm)
•
•
Retain the settings of the surface grinder and
grind all the other knives exactly the same.
The knives can be sharpened up to the limits
shown in the display.
0.0118 in.
(3 mm)
After this, the knives are used up and must be
replaced by new ones.
Service
l
7-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
V-Belts, Inspection, and Adjustment
The granulator is driven by 3 V-belts.
Checking the V-belts
The tension and condition of the V-belts must be checked after 20 - 30 hours
of operation at full load.
After this, check the V-belts for damage once a month.
Check the belt tension every 6 months.
•
•
Undo and remove the upper panel on the right-hand side of the granulator.
Rotate the V-belts a few turns.
Check that the belts are intact, undamaged and uncracked.
Check belt tension and adjust if necessary.
Motors up to 7.5 kW:
Load each one of the belts in turn with
•
WARNING: Pinch risk
between pulleys and
V-belts.
•
4.45 lbf. (20 N),
Motors up to 7,5 kW
centrally between the cutter and belt
pulleys. It should not be possible to
depress the belt more than about
0.197 in. (5 mm).
L = 0.197in. (5 mm); F = 4.45lbf. (20 N)
11 kW motor
L = 0.197in. (5 mm); F = 6.07 lbf (27 N)
11 kW motor:
•
Load each one of the belts in turn with 6.07 lbf. (27 N), centrally between
the cutter and belt pulleys. It should not be possible to depress the belt more
than about 0.197 in. (5 mm).
7-8
l
Service
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission (continued)
B
A
V-belt Adjustment
•
Remove the upper panel on the
right-hand side of the granulator.
•
CHS series-noise encapsulated
machine, remove the rear guard
plate above the motor and open the door.
Undo and remove the extraction pipe.
•
Alt. CHS series-machine with extraction fan, undo the quick coupling on
the outlet pipe stub.
•
•
•
Remove the granule bin.
Undo the motor screws (A) lightly, 4 pcs.
Adjust the belt tension by increasing/reducing the distance of the motor to
the cutter pulley, using the motor adjustment screws (B), 2 pcs.
Tighten the motor screws (33.2lb-ft [45 Nm] torque)
If the belt tension is adjusted, the belt need to be re-checked after 20 - 30
hours at full load.
•
•
Service
l
7-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Lubrication
Cutter Housing
The bearings in the cutter housing are permanently greased, and do not need greas-
ing in normal circumstances.
7-10
l
Service
Download from Www.Somanuals.com. All Manuals Search And Download.
Cutter Pulley/Motor Pulley
The upper panel on the right-hand side of the granulator must be removed to
remove/install the cutter or motor pulleys.
This makes the cutter and motor pulleys accessible.
Removal
Cutter Pulley
The pulley is mounted with a compres-
sion bush.
•
•
•
Undo all screws a few turns (8 pcs.)
Remove two screws.
Put a drop of oil into the extractor
hole (A), and insert the two screws.
Tighten the screws, using progressive
increased torque until the compression
bush comes away from the shaft.
Lift off the cutter pulley, complete with the
compression bush, from the shaft.
•
•
Motor Pulley
•
•
Undo the socket cap screw on the pulley.
Remove the pulley with a puller.
Installing
A
Motor Pulley
Lift the pulley onto the motor shaft, make sure that the key fits.
•
Tighten the pulley with the socket cap screws on the shaft,
88.5lb-ft (120 Nm).
Cutter Pulley
The pulley is fitted with a compression bush.
•
•
•
•
•
•
Clean and degrease the cutter pulley.
Oil the cutter shaft.
Oil the screws and fit the compression bush lightly on the pulley.
Lift the pulley on to the cutter shaft.
Make sure that the pulleys line up.
Tighten the screws in the compression bush.
Tighten the screws alternately with the same torque, progressively
increasing the torque to 14.8lb-ft (20 Nm).
•
•
Tap the compression bush between the shaft and the screws.
Use a block of wood or plastic.
Tighten the pulley with the compression bush.
Tighten the screws with alternating increased torque to 29.5lb-ft (40 Nm).
Service
l
7-11
Download from Www.Somanuals.com. All Manuals Search And Download.
7-12
l
Service
Download from Www.Somanuals.com. All Manuals Search And Download.
S E C T I O N
8
Spare Parts List
Cutting Chamber . . . . . . . . . . . . . . . . . . . . 8-3
Staggered Rotor . . . . . . . . . . . . . . . . . . . . 8-4
Open Rotor . . . . . . . . . . . . . . . . . . . . . . . 8-5
Knives . . . . . . . . . . . . . . . . . . . . . . . . . 8-6
Knives, Open Rotor . . . . . . . . . . . . . . . . . . 8-6
Transmission . . . . . . . . . . . . . . . . . . . . . . 8-7
Screen . . . . . . . . . . . . . . . . . . . . . . . . . 8-8
Screen Box . . . . . . . . . . . . . . . . . . . . . . . 8-8
Outfeed, Granule Bin Manual . . . . . . . . . . . . 8-9
Outfeed, Vaccum Suction/Blower
F-7/F-5 . . . . . . . . . . . . . . . . . . . . . 8-10
Hopper . . . . . . . . . . . . . . . . . . . . . . . . 8-11
Hopper - Noise encapsulated machine
with extraction fan . . . . . . . . . . . . . . 8-12
Hopper Device . . . . . . . . . . . . . . . . . . . . 8-13
Sound Cabin . . . . . . . . . . . . . . . . . . . . . . 8-14
Enclosure/Body . . . . . . . . . . . . . . . . . . . . 8-15
Safety
. . . . . . . . . . . . . . . . . . . . . . . . 8-16
Spare Parts List
l
8-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Spare Parts List
Ordering Spare Parts
Only use spare parts from Conair when replacing machine parts.
Orders should go to the representative in the country where the machine
was purchased.
When ordering, the following should be specified:
•
•
•
•
Machine designation, as specified on the machine plate.
Serial number, as specified on the machine plate.
Part number, as specified in the spare parts list.
Quantity, as specified in this spare parts list.
8-2
l
Spare Parts List
Download from Www.Somanuals.com. All Manuals Search And Download.
Cutting Chamber
3
16
5
13
9
17
1
15
10
11
2
4
6
7
14
12
18
8
Pos Qty.
Art. no.
Description
Pos
Qty.
Art. no.
Description
1
3-029705
3-030254
3-029706
3-030255
3-029707
3-030256
3-044924
3-048234
1-029513
1-041488
1-029514
1-041489
1-029507
4-030702
1-029508
4-030703
1-029509
4-030704
1-044912
4-048231
1-029510
4-030705
1-029511
4-030706
1-029512
4-030707
1-044913
4-048232
2-029518
4-030708
2-029519
4-030709
2-029520
4-030710
2-044915
2-044915
2-029521
4-030711
2-029522
4-030712
2-029523
4-030713
2-044914
2-044914
Cutter housing CHS-810
– ” – CHS-810 hardened
Cutter housing CHS-814
– ” – CHS-814 hardened
Cutter housing CHS-819
– ” – CHS-819 hardened
Cutter housing CHS-824
– ” – CHS-824 hardened
Side, right
3-029705
3-030254
3-029706
3-030255
3-029707
3-030256
3-029707
3-030256
3-029524
3-029525
3-029526
3-044916
4-026380
950079
Cutter housing CHS-810
– ” – CHS-810 hardened
Cutter housing CF-814
– ” – CHS-814 hardened
Cutter housing CHS-819
– ” – CHS-819 hardened
Cutter housing CHS-824
– ” – CHS-824 hardened
Support, screen box
2
3
4
1
1
1
1
1
1
1
1
1
8
1
1
1
1
1
1
1
1
1
1
1
Side, right
1
1
Support, screen box
Side, left
1
1
Support, screen box
Side, left
1
1
1
8
Support, screen box
Front side
9
1
8
1
8
1
8
1
8
1
8
1
8
1
8
Lid
Front side
10
Cylindric pin
1
1
1
1
Front side
11 14 14 14 14 14 14 14 14
940005
Socket cap screw
1
1
1
1
Front side
12
13
14
15
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
940104
Socket cap screw
1
1
1
1
Front side
940213
Socket cap screw
1
1
1
1
Front side
940743
Stop screw
1
1
1
1
Front side
3-029708
3-030257
Cutter housing CHS-810 w 3:rd knife
Cutter housing CHS-810 w 3:rd knife
hardened
1
1
1
1
Front side
5
6
7
1
1
1
Rear side
1
1
1
Rear side
3-029709
3-030258
Cutter housing CHS-814 w 3:rd knife
Cutter housing CHS-814 w 3:rd knife
hardened
Rear side
Rear side
Rear side
3-029710
3-030259
Cutter housing CHS-819 w 3:rd knife
Cutter housing CHS-819 w 3:rd knife
hardened
Rear side
Rear side
Rear side
3-044925
3-048235
Cutter housing CHS-824 w 3:rd knife
Cutter housing CHS-824 w 3:rd knife
hardened
Support rule, rear
Support rule, rear
Support rule, rear
Support rule, rear
Support rule, rear
Support rule, rear
Support rule, rear
Support rule, rear
Support rule, front
Support rule, front
Support rule, front
Support rule, front
Support rule, front
Support rule, front
Support rule, front
Support rule, front
16
17
18
1
1
2
1-029554
4-030243
1-029555
4-030244
1-029556
4-030245
1-044917
4-048233
2-029557
4-030246
2-029558
4-030247
2-029559
4-030248
2-044918
2-044918
940742
Rear for 3:rd fixed knife
Rear for 3:rd fixed knife, hardened
Rear for 3:rd fixed knife
Rear for 3:rd fixed knife, hardened
Rear for 3:rd fixed knife
Rear for 3:rd fixed knife, hardened
Rear for 3:rd fixed knife
Rear for 3:rd fixed knife, hardened
Support rule for 3:rd fixed knife
Support rule for 3:rd fixed knife
Support rule for 3:rd fixed knife
Support rule for 3:rd fixed knife
Support rule for 3:rd fixed knife
Support rule for 3:rd fixed knife
Support rule for 3:rd fixed knife
Support rule for 3:rd fixed knife
Socket cap screw
1
1
1
1
1
1
1
1
2
1
2
1
2
1
2
1
2
1
2
1
2
Spare Parts List
l
8-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Staggered Rotor
12
8
2
15
3
5
14
6
10
7
11
4
1
13
9
Pos Qty.
Art. no.
3-29702
3-30260
3-29703
3-30261
3-29704
3-30262
3-44926
3-48236
1-029530 Cutter shaft 3-blade
1-029531 Cutter shaft 3-blade
1-029532 Cutter shaft 3-blade
3-044919 Cutter shaft 3-blade
3-029501 Segment
Description
Cutter CHS-810 3-blade
Cutter CHS-810 3-blade hardened
Cutter CHS-814 3-blade
Cutter CHS-814 3-blade hardened
Cutter CHS-819 3-blade
Cutter CHS-819 3-blade hardened
Cutter CHS-824 3-blade
Cutter CHS-824 3-blade hardened
1
1
1
1
1
1
1
4
2
1
5
2
1
5
2
3
2
2
2
2
3
2
3
2
4
2
3-029502 Ring
4-030249 Ring
3-029504 Support rule
4-030250 Support rule
4-029529 Sleeve
2
4
6
9
12
15
6
1
9
1
12
1
15
1
5
6
1
1
1
1
1
1
1
1
2-029505 Plummer block, right
2-030714 Plummer block, right
2-029506 Plummer block, left
2-030715 Plummer block, left
3-029527 Lid, left
1
1
1
1
7
1
1
1
1
1
1
1
2
2
6
6
8
4
1
1
1
2
2
6
6
8
4
1
1
1
2
2
6
6
8
4
1
1
1
2
2
6
6
8
4
8
9
1
1
2
2
6
6
8
4
1
1
2
2
6
6
8
4
1
1
2
2
6
6
8
4
1
1
2
2
6
6
8
4
4-029528 Lid, right
10
11
12
13
14
15
960182
960183
940579
940007
940071
940032
Bearing
Sealing ring
Socket cap screw
Socket cap screw
Socket cap screw
Socket cap screw
8-4
l
Spare Parts List
Download from Www.Somanuals.com. All Manuals Search And Download.
Open Rotor
5
10
2
6
1
13
11
4
3
12
7
8
9
Pos Qty.
Art. no.
3-30113
3-30263
3-29753
3-30264
3-30114
3-30265
3-44927
3-48237
1-030104 Cutter 3-blade
1-029743 Cutter 3-blade
1-030106 Cutter 3-blade
1-044920 Cutter 3-blade
3-029502 Ring
Description
Cutter CHS-810 3-blade open
Cutter CHS-810 3-blade open hardened
Cutter CHS-814 3-blade open
Cutter CHS-814 3-blade open hardened
Cutter CHS-819 3-blade open
Cutter CHS-819 3-blade open hardened
Cutter CHS-824 3-blade open
Cutter CHS-824 3-blade open hardened
1
2
1
2
1
1
2
1
1
2
1
1
2
1
2
1
2
1
2
1
2
1
4-030249 Ring
4-029529 Sleeve
3
4
1
1
1
1
1
1
1
1
2-029505 Plummer block, right
2-030714 Plummer block, right
2-029506 Plummer block, left
2-030715 Plummer block, left
3-029527 Lid, left
1
1
1
1
5
1
1
1
1
1
1
1
2
2
6
6
8
4
1
1
1
2
2
6
6
8
4
1
1
1
2
2
6
6
8
4
1
1
1
2
2
6
6
8
4
6
7
1
1
2
2
6
6
8
4
1
1
2
2
6
6
8
4
1
1
2
2
6
6
8
4
1
1
2
2
6
6
8
4
4-029528 Lid, right
8
960182
960183
940579
940007
940071
940032
Bearing
Sealing ring
Socket cap screw
Socket cap screw
Socket cap screw
Socket cap screw
9
10
11
12
13
Spare Parts List
l
8-5
Download from Www.Somanuals.com. All Manuals Search And Download.
1
4
Knives
5
2
3
Pos Qty.
Art. no.
Description
Note
6
Granulator CHS-810
Granulator CHS-814
Granulator CHS-819
Granulator CHS-824
Knife, rotating
7
1
2
6
2
9
2
12 15
3-029503
2-029515
2-029516
2-029517
3-044922
2-029515
2-029516
2-029517
3-044922
940004
Knife, fixed
Knife, fixed
2
2
Knife, fixed
Knife, fixed
3
1
Knife, third fixed
Knife, third fixed
Knife, third fixed
Knife, third fixed
Socket cap screw
Washer
1
1
1
4
5
6
7
12 18 24 30
12 18 24 30
940031
8
4
12 16 20
10
940778
Socket cap screw
Socket cap screw
6
8
940779
for 3:rd fixed knife
8
Knives, Open Cutter
12
11
13
14
9
10
15
Pos Qty.
Art. no.
Description
Note
Granulator CHS-810 with open cutter
Granulator CHS-814 with open cutter
Granulator CHS-819 with open cutter
Granulator CHS-824 with open cutter
Knife, rotating
8
9
6
2
1
3-030108
3-029750
3-030109
2-044923
2-029515
2-029516
2-029517
3-044922
2-029515
2-029516
2-029517
3-044922
940776
6
2
1
Knife, rotating
6
2
1
Knife, rotating
6
2
1
Knife, rotating
Knife, fixed
Knife, fixed
Knife, fixed
Knife, fixed
10
Knife, third fixed
Knife, third fixed
Knife, third fixed
Knife, third fixed
Socket cap screw
Washer
11 12 12 12 12
12 12 12 12 12
13 12 12 12 12
14 12 12 12 12
4-029751
940302
Screw
940057
Socket cap screw
Socket cap screw
8
4
12 16 20
18
940057
15
6
8
940057
Socket cap screw
for 3:rd fixed knife
8-6
l
Spare Parts List
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
4
1
5
7
3
12
6
11
10
8
2
9
Pos Qty.
Art. no.
Description
Transmission 4,0 kW 1000 rpm 400 V
Transmission 5,5 kW 1000 rpm 400 V
Transmission 5,5 kW 1500 rpm 400 V
Transmission 7,5 kW 1500 rpm 400 V
Transmission 11,0 kW 1500 rpm 400 V
Cutter pulley
Motor pulley
Belt tensioner
Motor 4,0 kW
Motor 5,5 kW
Motor 5,5 kW
Motor 7,5 kW
Motor 11,0 kW
Coupling
1
2
3
4
1
1
2
1
1
1
2
1
1
2
1
1
2
1
1
2
1-29545
3-29546
3-29552
911189
911178
911171
911172
911177
930222
970214
930221
940092
940031
940744
940648
940051
1
1
1
1
1
1
3
4
6
2
1
1
5
6
1
1
3
4
6
2
1
1
1
1
3
4
6
2
1
1
1
1
3
4
6
2
1
1
1
1
3
4
6
2
1
1
Ring, polyester
V-belt
7
8
Screw
9
Washer
10
11
12
Screw
Washer
Socket cap screw
Spare Parts List
l
8-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Screen
Pos Qty.
1
Art. no.
Description
Granulator CHS-810
Granulator CHS-814
Granulator CHS-819
Granulator CHS-824
Screen
Note
1
1
1
1
1
3-29574
3-31688
4-30251
4-31691
3-29575
3-31689
4-30252
4-31692
3-29576
3-31690
4-30253
4-31693
3-46065
3-48239
4-48238
4-48240
Screen
stitch reduced
stitch reduced
stitch reduced
stitch reduced
stitch reduced
stitch reduced
stitch reduced
stitch reduced
Screen hardened
Screen hardened
Screen
1
1
1
1
Screen
Screen hardened
Screen hardened
Screen
1
1
1
1
Screen
Screen hardened
Screen hardened
Screen
1
1
1
1
Screen
Screen hardened
Screen hardened
✐
NOTE: Specify art no. and required hole diameter, Ø 4, 6, 8 or 10 mm.
Screen Box
3
4
5
2
1
Pos Qty.
Art. no.
Description
Note
Granulator CHS-810
Granulator CHS-814
Granulator CHS-819
Granulator CHS-824
5
1
1
1
1-29560 Screen box
1-29656 Screen box
1-29561 Screen box
1-29657 Screen box
1-29562 Screen box
1-29658 Screen box
1-44970 Screen box
1-48246 Screen box
stitch reduced
stitch reduced
stitch reduced
stitch reduced
1
1
1
1
1
1
2
1
1
4
2
3
4
5
2
1
1
4
2
1
1
4
2
1
1
4
950532
Star knob
4-30327 Locking bolt
4-30328 Locking bolt
940155
Washer
8-8
l
Spare Parts List
Download from Www.Somanuals.com. All Manuals Search And Download.
Granule Bin Manual (Optional)
1
Pos Qty.
Art. no.
Description
Note.
Granulator CHS-810
Granulator CHS-814
Granulator CHS-819
Granulator CHS-824
Granule bin
1
1
1-29577
1-29578
1-29579
1-47106
manual 15 L
manual 22 L
manual 29 L
manual 36 L
1
Granule bin
Granule bin
Granule bin
1
1
Spare Parts List
l
8-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Vaccum Suction /Blower F-7/F-15
Optional
27
25
26
12
19
23
15
20
1
24
17
14
8
21
9
13
10
18
22
11
16
Pos Qty.
Art. no.
Description
Note.
Granulator CHS-810
Granulator CHS-814
Granulator CHS-819
Granulator CHS-824
Granule bin
Granule bin
Granule bin
Granule bin
Distance
Pipe stub D-100
Pipe stub, inlet
Holder, blower
Pipe stub, outlet
Pipe stub, outlet
Holder, blower
Quick coupling ring
Blower F7/D4
1
1
1-30082
1-29633
1-30087
3-46429
3-29759
2-29639
3-30267
1-22825
3-13138
3-10332
4-24655
920415
920206
920421
940347
940004
940201
940426
940039
940015
940031
940592
940213
1-22824
970152
940147
vaccum/blower
vaccum/blower
vaccum/blower
vaccum/blower
1
1
1
8
9
10
11
12
1
1
1
1
1
1
1
1
1
1
4
4
4
4
8
6
8
4
2
1
1
8
1
1
1
1
1
1
1
1
1
1
4
4
4
4
8
6
8
4
2
1
1
8
1
1
1
1
1
1
1
1
1
1
4
4
4
4
8
6
8
4
2
1
1
8
1
1
1
1
1
1
1
1
1
1
4
4
4
4
8
6
8
4
2
1
1
8
F7
F15
13
14
15
Blower F15/D6
16
17
18
19
20
21
22
23
24
25
26
27
Socket cap screw M10
Socket cap screw M10
Socket cap screw M10
Screw M8
Socket cap screw M6
Nut M10
Washer BRB
Washer BRB FZB
Socket cap screw M6
Cover, blower
Sealing ring
Screw
8-10
l
Spare Parts List
Download from Www.Somanuals.com. All Manuals Search And Download.
Hopper
11
1
16
17
1
18
15
9
6
3
4
10
8
7
2
13
5
12
24
Pos Qty.
Art. no.
Description
Pos Qty.
Art. no.
Description
Granulator CHS-810
Granulator CHS-814
Granulator CHS-819
Granulator CHS-824
Hopper, front
Hopper, front
Hopper, front
Hopper, front
Frame
Granulator CHS-810
Granulator CHS-814
Granulator CHS-819
Granulator CHS-824
List
1
2
3
1
1
1
2-44613
2-44695
2-44665
2-46082
1-29595
1-29596
1-29597
1-46075
4-30495
4-29734
4-30628
4-46076
4-29646
4-30327
4-30328
950532
940097
940071
940155
940696
970141
970218
14
15
16
17
18
20
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
970148
1
1
1
4-30093
4-22129
940162
Stop double
Distance
1
1
1
1
1
Washer BRB
Socket cap screw M8
Feed tray
940662
Frame
3-44684
3-44595
3-44688
3-46139
2-30484
2-29799
2-29798
3-46133
Frame
1
Feed tray
Frame
1
1
Feed tray
Shaft
1
1
Feed tray
Shaft
24
1
Flaps
Shaft
1
Flaps
1
1
1
1
2
6
2
4
1
1
1
Shaft
Flaps
4
5
1
1
1
2
6
2
4
1
1
1
1
1
1
2
6
2
4
1
1
1
1
1
1
2
6
2
4
1
1
1
Bracket, key
Locking bolt M12
Locking bolt M12
Star knob
Flaps
6
7
8
Socket cap screw M8
Socket cap screw M5
Washer BRB FZB
Stop screw
List
9
10
11
12
13
List
Spare Parts List
l
8-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Hopper - Noise encapsulated machine with
with Conveyor (Optional)
1
4
2
3
Pos Qty.
Art. no.
Description
Granulator CHS-810
Granulator CHS-814
Granulator CHS-819
Granulator CHS-824
Sound trap
1
1
2-30673
2-30654
2-30666
1
Sound trap
Sound trap
Sound trap
Washer AMF
Socket cap screw M8
Socket cap screw M8
Socket cap screw M8
Socket cap screw M8
List
1
4
1
2
3
8
4
-
940020
940097
940032
940070
4
4
1
4
1
4
1
1
970218
8-12
l
Spare Parts List
Download from Www.Somanuals.com. All Manuals Search And Download.
Hopper Device
Noise encapsulated machine
with extraction fan
Noise encapsulated machine
for sheet material/profiles
5
7
7
10
9
8
11
9
11
4
5
3
2
3
6
1
6
1
1
6
Pos Qty.
Art. no.
Description
Note.
Hopper device, granulator CHS-810
for hopper 2-44613
for hopper 2-44548
for hopper 2-44665
for hopper 2-46082
Noise encapsulated machine with extraction fan
Hopper device, granulator CHS-814
Noise encapsulated machine with extraction fan
Hopper device, granulator CHS-819
Noise encapsulated machine with extraction fan
Hopper device, granulator CHS-824
Noise encapsulated machine with extraction fan
Hopper device, granulator CHS-810
Noise encapsulated machine for sheet material/profiles
Hopper device, granulator CHS-814
Noise encapsulated machine for sheet material/profiles
Hopper device, granulator CHS-819
Noise encapsulated machine for sheet material/profiles
Hopper device, granulator CHS-824
Noise encapsulated machine for sheet material/profiles
1
2
2
2
2
3-29777
3-30497
3-30325
3-29779
3-30498
3-30326
920768
920769
920763
920655
940032
940200
940054
940585
940016
950430
Bracket
1
1
1
1
1
1
Bracket
2
3
1
1
1
1
1
1
1
1
Sleeve
Sleeve
1
1
1
1
Sleeve
4
5
1
1
1
1
1
1
1
1
Sleeve
Gas spring
Gas spring
Gas spring
Gas spring
Socket cap screw M8
Socket cap screw M8
Socket cap screw M8
Washer
1
1
2
1
1
1
5
6
7
8
9
10
11
4
4
4
4
4
4
4
4
2
1
1
1
5
2
1
1
1
5
2
1
1
1
5
2
7
1
2
7
1
2
7
1
2
7
1
Nut
Sealing end
Spare Parts List
l
8-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Sound Cabin
17
7
1
3
9
16
12
2
6
5
4
19
18
13
10
20
8
15
Pos Qty.
Art. no.
Description
14
11
Granulator CHS-810-Noise Encapsulated Machine
Granulator CHS-814-Noise Encapsulated Machine
Granulator CHS-819-Noise Encapsulated Machine
Granulator CHS-824-Noise Encapsulated Machine
1
2
1
1
1
1
1
1
1-29581
2-29583
2-29584
2-29585
2-46146
2-29586
2-29587
2-29588
1-46147
2-29589
2-29590
2-29591
1-46148
3-29592
2-29593
2-29613
2-29614
2-29615
2-46149
329655
940032
950555
950533
940261
950557
950556
940076
940054
970218
970148
940213
940257
Cover, left
Cover, front
Cover, front
Cover, front
Cover, front
Cover, rear
Cover, rear
Cover, rear
Cover, rear
Door
1
1
1
1
1
3
4
1
1
1
1
Door
Door
1
1
1
Door
5
6
7
1
1
1
1
1
1
1
Holder, rear
Bracket, cover, rear
Border
1
Border
1
Border
1
1
3
1
2
5
4
8
8
2
1
1
Border
8
9
1
3
1
2
5
4
8
8
2
1
1
1
3
1
2
5
4
8
8
2
1
1
1
3
1
2
5
4
8
8
2
1
1
List
Socket cap screw
Lock, door lock
Hinge
10
11
12
13
14
15
16
17
18
Rivet
Nut, blind rivet
Nut, blind rivet
Socket cap screw M5
Socket cap screw M8
List
List
19 15 15 15 15
20
Socket cap screw M6
Rivet
4
4
4
4
8-14
l
Spare Parts List
Download from Www.Somanuals.com. All Manuals Search And Download.
8.17 Enclosure/Body
23
10
2
14
20
4
6
17
18
19
16
12
11
13
7
3
21
22
5
9
15
8
Pos Qty.
Art. no.
Description
Granulator CHS-810
Granulator CHS-814
Granulator CHS-819
Granulator CHS-824
Cover, transmission
Lid
1
2
3
1
1
1
1
1
1
1
1
1-29542
2-29582
940213
940647
991567
950269
950321
4-30274
940027
970195
970218
970141
970148
1-29539
1-29540
1-29541
1-46145
950148
950147
940051
940024
940155
940037
4-30076
940104
2-44514
10 10 10 10
12 12 12 12
Socket cap screw
Torx screw
Lock, door lock
Nut, blind fastening
Nut, blind fastening
Stop, door
Nut M6
Noise absorber
List
4
5
6
2
2
2
2
12 12 12 12
7
8
9
10
11
12
13
14
6
1
2
1
1
1
1
1
6
1
2
1
1
1
1
6
1
2
1
1
1
1
6
1
2
1
1
1
1
List
List
Bottom plate
Bottom plate
Bottom plate
Bottom plate
Wheel, fixed
Wheel, foot brake
Socket cap screw
Nut
Washer
Socket cap screw
Distance
Socket cap screw
Push button mounting bracket
1
1
1
2
2
4
4
4
15
16
17
18
19
2
2
4
4
4
2
2
4
4
4
2
2
4
4
4
20 14 14 14 14
21
22
23
2
2
1
2
2
1
2
2
1
2
2
1
Spare Parts List
l
8-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety
1
3
4
Pos Qty.
Art. no.
Description
Granulator CHS-810
Granulator CHS-814
Granulator CHS-819
Granulator CHS-824
Switch
7
5
1
2
3
4
5
6
7
2
1
1
6
4
4
6
2
1
1
6
4
4
6
2
1
1
6
4
4
6
2
1
1
6
4
4
6
911002
911003
911004
911005
940076
940611
940267
Breaking key
Breaking key
Cover washer
Socket screw
Socket screw
Nut
2
8-16
l
Spare Parts List
Download from Www.Somanuals.com. All Manuals Search And Download.
S E C T I O N
9
Wiring Diagram
Wiring Diagram . . . . . . . . . . . . . . . . . . . . 9-2
Current sensing relay . . . . . . . . . . . . . . . . 9-3
Connection . . . . . . . . . . . . . . . . . . . . . . . 9-4
Example . . . . . . . . . . . . . . . . . . . . . . . . . 9-5
Wiring Diagram
l
9-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Wiring diagram
Never change or modify the basic
electrical settings of the granulator,
without first obtaining permission
from Conair.
If the granulator settings are changed,
the machine can be seriously dam-
aged. All Warranties and Conair’s
Product Liability will be void, if the
basic settings of the granulator are
changed. All maintenance and serv-
ice work must be done by trained and
competent personnel!
Electrical installation must only be
done by a competent electrician!
The distribution box of the granulator is
located on the right, low down.
CHS Noise Encapsulated Machine
Motor overload circuit
breaker (F1)
CHS Noise Encapsulated Machine
with Conveyor
Conveyor belt overload
circuit breaker (F3)
Blower overload circuit
breaker (F2)
Motor overload circuit
breaker (F1)
9-2
l
Wiring Diagram
Download from Www.Somanuals.com. All Manuals Search And Download.
Current Sensing Relay
The granulator can be equipped with an optional current sensing relay to
control the feed equipment.
The current sensing relay detects the mill motor current consumption and
can temporarily stop accessories such as conveyors, roller feeders etc to
avoid putting further material into the hopper, when the mill is running
under heavy loading.
The relay stops and re-starts accessory equipment automatically,
without re-setting.
C
T1
Relay functions and normal settings:
T1
T2
A
–
–
–
–
Start delay, prevents the relay from breaking
on connection (0.1 - 10 sec).
The default start delay is 0.1 seconds.
Reaction time, prevents the relay from breaking
during temporary high loading (0.1 - 3 sec).
Default reaction time is 3.0 seconds.
Hysteresis, adjustable between 5 - 50%
of the set limit.
Default hysteresis is 20 %.
Limit value, adjustable between 0 - 100 %.
A
T2
B
B
Default setting depends on the current transformer size.
Check the current transformer size and then check the
default setting for this granulator.
C
–
Relay function, N = normal; I = inverted;
Wiring Diagram
l
9-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Connection
The current sensing relay is connected in series with
the mill motor via a current transformer.
The transformer is connected between M and E1/E2/E3
depending on the secondary current.
(For transformers with transformation to 1 A, this is
connected to E2.)
Default setting for this granulator:
Granulator motor, rated current: . . . . . . . . . . . . . . . .= . . . . . . . A
Current transformer:
Start delay T1:
Reaction time T2:
Limit values:
. . . . . . . . . . . . . . . . . . . . . . ./1A
0,1 sec.
3,0 sec.
other value: . . . . . . . . . . . . . . . . . .
other value: . . . . . . . . . . . . . . . . . .
% . . . . . . . . . . . . . = . . . . . . . . . . . . . . . . . A
% . . . . . . . . . . . . . = . . . . . . . . . . . . . . . . . A
Hysteresis:
9-4
l
Wiring Diagram
Download from Www.Somanuals.com. All Manuals Search And Download.
Example
The granulator is equipped with a current sensing relay to control a conveyor.
A motor of 7.5 kW has a rated current of about 15 A.
When this star/delta is started, it pulls about 15 A/
i.e. about 9 A per phase.
C
T1
Relay Setting:
Motor size 15 A/
= 8,7 A per phase
T1 – Start delay setting 0.1 second.
T2 – Reaction time setting 3.0 seconds.
A
B
C
–
–
–
Hysteresis 20 %.
Limit value 30 %.
A
T2
B
Relay function N normal.
•
The current transformer size is 30/1A.
•
•
The current transformer is connected to E2 (1 A).
In a current transformer with a transformation ratio of 30/1, the limit value
B should be set to 30 % or 9 A (30 A = 100 %).
•
The current sensing relay detects the current consumption of the granulator
motor and stops the conveyor, when the granulator motor exceeds 9 A for
3 seconds, to prevent further material from being fed into the hopper.
•
The relay re-starts the conveyor automatically when the granulator motor
consumption has fallen 20 % below 9 A, i.e. to 7 A without a time delay.
Wiring Diagram
l
9-5
Download from Www.Somanuals.com. All Manuals Search And Download.
9-6
l
Wiring Diagram
Download from Www.Somanuals.com. All Manuals Search And Download.
S E C T I O N
1 0
Layout
CHS Series, Allround Hopper Noise Encapsulated,
Hopper Loader, Non Soundproof . . . . . . . 10-2
CHS Series, Allround Hopper Noise Encapsulated,
Blower F-7 Cyclone AX-7,5 with Holder/Bag
Holder, Soundproof . . . . . . . . . . . . . . . 10-2
CHS Series, Allround Hopper Noise Encapsulated
with Conveyor, Band Conveyor, Hopper Loader,
Non Soundproof . . . . . . . . . . . . . . . . . . 10-3
CHS Series, Allround Hopper Noise Encapsulated
with Conveyor, Band Conveyor, Blower F-7,
Cyclone AX-7,5, Soundproof . . . . . . . . . . 10-3
Layout
l
10-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Layout
CHS Series, Allround Hopper Noise Encapsulated,
Hopper Loader, Non Soundproof
B
10.25in.
(227mm)
35.5in. (902mm)
54.75in. (1390mm)
A
A
B
CHS-810
CHS-814
CHS-819
CHS-824
26.75in. (679mm) 9.44in. (240mm)
31.50in. (800mm) 14.13in. (359mm)
36.25in. (920mm) 18.86in. (479mm)
41in. (1041mm) 23.63in. (600mm)
CHS Series, Allround Hopper Noise Encapsulated, Blower
F-7 Cyclone AX-7,5 with Holder/Bag Holder, Soundproof
A
B
12.60in. (320mm)
CHS-810 26.77in. (680mm) 9.45in. (240mm)
CHS-814 31.50in. (800mm) 14.17in. (360mm)
CHS-819 36.22in. (920mm) 18.90in. (480mm)
CHS-824
9.45in.
(240mm)
7.87in.
(200mm)
B
18.11in.
12.60in.
(320mm)
(460mm)
35.04in. (890mm)
A
8.66in. (220mm)
61.42in. (1560mm)
18.50in. (470mm)
10-2
l
Layout
Download from Www.Somanuals.com. All Manuals Search And Download.
CHS Series, Allround Hopper Noise Encapsulated with Conveyor,
Band Conveyor, Hopper Loader, Non Soundproof
7.87in.
(200mm)
B
1.97in.
(50mm)
A
35.04in. (890mm)
33.86in. (860mm)
146.85 in. (3730mm)
7.87in.
(200mm)
8.66in. (220mm)
A
B
CHS-810 26.38in. (670mm) 9.45in. (240mm)
CHS-814 31.10in. (790mm) 14.17in. (360mm)
CHS-819 35.83in. (910mm) 18.90in. (480mm)
CHS-824
CHS Series, Allround Hopper Noise Encapsulated with Conveyor,
Band Conveyor, Blower F-7, Cyclone AX-7,5, Soundproof
12.60in. (320mm)
7.87in.
(200mm)
B
A
33.86in. (860mm)
146.85 in. (3730mm)
900
7.87in.
(200mm)
12.60in. (320mm)
8.66in. (220mm)
A
B
CHS-810 26.77in. (680mm) 9.45in. (240mm)
CHS-814 31.50in. (800mm) 14.17in. (360mm)
CHS-819 36.22in. (920mm) 18.90in. (480mm)
CHS-824
Layout
l
10-3
Download from Www.Somanuals.com. All Manuals Search And Download.
10-4
l
Layout
Download from Www.Somanuals.com. All Manuals Search And Download.
S E C T I O N
1 1
Accessories
Ordering Spare Parts . . . . . . . . . . . . . . . . 11-2
Pre-Setting of Rotating Knives, Granulator
with Open Cutter . . . . . . . . . . . . . . 11-3
Third Fixed Knife, Removing, Installing . . . 11-5
Band Conveyor . . . . . . . . . . . . . . . . . . . . 11-6
Spare Parts for the Band Conveyor . . . . . . 11-8
Layout
l
11-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories
Ordering Spare Parts
Only use original Conair spare parts when replacing machinery components.
Orders should be sent to the representative in the country where the machine
was purchased.
When ordering spare parts, please specify:
•
•
•
•
Machine type/designation, on the machine´s rating plate.
Serial number, on the machine´s rating plate.
Part number, from this list of spare parts.
Number of components.
11-2
l
Accessories
Download from Www.Somanuals.com. All Manuals Search And Download.
Pre-Setting of Rotating Knives,
Granulator with Open Cutter
Knives can only be pre-set on granulators with open cutter.
The knives are pre-set on a jig.
The jig is not included when the
granulator is delivered, but is
a very practical accessory.
Setting Up the Knives
✐
NOTE: The knives must be
sharpened before pre-setting.
When the machine is delivered, the jig is calibrated
against the set screws welded solid in the granulator cutter.
The jig gives the correct clearance of 0.008 - 0.012 in.
(0.20 - 0.30 mm).
•
•
•
Screw the adjustment screws on a rotating knife in somewhat.
Put knife in the jig, with the edge downwards.
Put an 0.008in. (0.20 mm) feeler gauge between the adjustment screws
and the rear of the jig.
•
•
Unscrew the adjustment screws
until the feeler gauge begins to bind.
The pre-setting is now completed
and the knife can be installed in the cutter.
Installation of Pre-Set Knives.
✐
NOTE: Each time the knives are changed, the
fastening screws must be replaced by new ones.
Install one pair of knives at a time.
•
•
•
•
Clean the knife attachments.
Install one pair of knives
Install the attachment screws with washers loosely.
Adjust the pair of knives against the outer edges of the cutter housing.
Accessories
l
11-3
Download from Www.Somanuals.com. All Manuals Search And Download.
✐
NOTE: The knives must butt up against the rings on the outer edges
of the cutter housing.
•
•
•
Make sure that the knives butt up against the rear of the knife attachment.
Tighten the fastening screws, tightening torque 162.26lb-ft (220 Nm).
Re-check that the knife clearance is 0.008 - 0.012 in. (0.20 - 0.30 mm).
Check against both the front and rear fixed knives.
•
Re-check that the knives butt up against the outer edges of the
cutter housing.
•
Install the remaining pairs of knives in the same way.
11-4
l
Accessories
Download from Www.Somanuals.com. All Manuals Search And Download.
Third Fixed Knife
As an optional extra, the granulator can be equipped with a third fixed knife to
increase the efficiency of the granulator.
Open the hopper to install/remove the third fixed knife.
CHS series-noise encapsulated machine, remove the rear guard plate over the
motor and open the door.
Removal
1
Undo and remove the screws
(A) which hold the knife.
Remove the knife (B).
Clean the knife attachments
where the knife was installed.
2
3
Installation
1
Install the knife on the knife
attachment.
C
B
2
Screw in the socket cap screws
(A), so that the support rule (C)
lightly supports the knife.
Press the knife firmly into the
3
✐ knife attachment to bed it down.
NOTE: The screws in the rear
of the knife attachment are
bonded in place.
✐
NOTE: The knife has a fixed
position and no adjustment
may be done.
A
4
Tighten the screws (A), with an
alternating tightening torque to 29.50 lb-ft (40 Nm).
Sharpening
The third fixed knife is disposable and is changed
when necessary.
Accessories
l
11-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Band Conveyor
The band conveyor is designed for transporting plastic waste. The conveyor is
constructed from steelbeam. The frame pieces are assembled with cross sections
and screw.
The conveyor can be fitted with a metal-free zone and a metal detector.
Safety
When performing any work with the band conveyor, both the circuit-breaker and
the main circuit-breaker must be “Off”. Alternatively, the connector must be
pulled out of the power point on the granulator’s electrical cabinet!
The conveyor is designed for plastic waste. Do not use the conveyor for tasks
other than it is intended for.
Nobody should be on the conveyor or step on it during operation.
If the conveyor has stopped due to an error, or if the emergency stop has been
pressed, it must not be re-started until the cause has been established and the
appropriate action has been taken.
Mobile conveyors must always be transported in a lowered position.
Warning! When using the conveyor belt with carriers: Be careful not to let
the carriers catch your foot, arm, or article of clothing.
Installation
When installing, adjust so that the band conveyor is balanced diagonally.
If the floor of the installation site is very uneven, it should be made even before
installation.
Electrical Connection
The band conveyor should be connected up by an authorised electrician.
Connect the cables to the electrical cabinet according to the markings and the
granulator’s electrical scheme (see Section 9). Alternatively, connect the band con-
veyor to the electrical cabinet with the connector.
Switch on the main circuit-breaker on the electrical cabinet. Press the start button
and check that the belt moves in the right direction.
If the belt moves in the wrong direction.
Shift the two phases in the connection to the contactor for the band conveyor in
the electrical cabinet. Alternatively, shift the two phases in the connection to the
connector.
11-6
l
Accessories
Download from Www.Somanuals.com. All Manuals Search And Download.
Starting
When the band conveyor is started for the first time, the belt’s position on the
rollers should be checked. The belt must not move obliquely.
If the belt moves obliquely.
When the belt moves obliquely. Screw one adjusting screw at a time. Only screw
a 1/4 turn. Wait and let the belt move for a few minutes. Check, adjust, wait, and
check again until the belt moves straight.
Belt tension.
The conveyor belt’s length has 1% tolerance. Never tension the belt’s adjusting
screws with a greater tightening torque than 5 Nm.
Maintenance
During all maintenance work on the band conveyor, both the circuit-breaker and
the main circuit-breaker must be “Off”. Alternatively, the connector must be pulled
out of the power point!
Regularly check the conveyor belt’s wear and its position on the rollers. The belt
must not move obliquely! Adjust as necessary according to the instructions under
“Starting - If the belt moves obliquely” (see previous Section).
Clean the belt using a light cleaning agent. Do not use any sharp objects, strong
cleaning agents or chemicals which can damage the belt.
Trouble-shooting
A
If the band conveyor does not start
The conveyor belt motor has an overload circuit
B
breaker, F3, in the distribution cabinet, which trips
if you jam or overload the conveyor belt.
This is indicated in the window (A) which then
shows an “0”.
To reset, press the “reset” button (B).
Also check the wiring diagram in Section 9, additions and modifications can occur.
Accessories
l
11-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Spare Parts for the Band Conveyor
31
34
16
23
25
6
30
5
37
29
22
17
19
28
32
7
8
36
35
33
20
15
10
18
21
14
1
11
9
13
27
26
24
4
2
3
12
Pos Qty.
Art. no.
Description
Pos Qty.
Art. no.
Description
3-030648
3-030650
3-030652
2-030649
2-030651
2-030653
2-030692
2-030680
2-022657
2-030693
2-030681
2-023510
4-020496
2-022654
2-023508
2-023956
2-023957
2-030694
2-030687
2-022658
4-007550
2-030695
2-030688
2-022659
950412
Band conveyor B200 CC2700
Band conveyor B350 CC2700
Band conveyor B450 CC2700
Band conveyor
Band conveyor
Band conveyor
Bracket wheel
Bracket wheel
Bracket wheel
Bracket wheel
Bracket wheel
Bracket wheel
Shaft
18
19
20
21
22
2
4
6
4
4
2
2
4
6
4
4
940059
940015
940317
940155
940031
Nut
4
6
4
4
Nut
Nut
1
2
3
1
1
1
Washer
Washer
Washer
Retaining ring SGA
Sealing end
1
1
1
1
1
23 22 22 22 940162
24
25
26
2
2
1
2
2
1
2
2
1
950061
950267
911006
Connector 6-pol
Pos Qty.
Art. no.
Description
3-030689
3-030690
3-030691
2-030648
2-030650
2-030652
2-022341
2-022342
2-010792
910589
Band conveyor B200 CC2700 MD200P
Band conveyor B350 CC2700 MD350P
Band conveyor B450 CC2700 MD450P
Band conveyor for metal detector
Band conveyor for metal detector
Band conveyor for metal detector
Holder control
1
1
1
1
1
1
4
5
6
7
8
9
1
1
1
1
1
1
1
1
1
1
1
Bracket upper left
Fäste upper right
Leg left
27
1
1
1
1
1
1
1
Leg right
28
29
30
31
32
1
1
1
1
1
1
1
1
1
Bracket wheel rear
Bracket wheel rear
Bracket wheel rear
Slewing brack
Stirrup leg
Holder warning
1
2
1
Pole warning
1
2
Warning lamp
10
11
2
1
910964
Metal detector MD200
Metal detector MD350
Metal detector MD450
Screw
1
911214
Stirrup leg
1
5
8
4
1
2
910963
1
2
2
4
6
Stirrup leg
33
34
35
36
37
5
8
4
1
2
5
8
4
1
2
940057
12
13
14
15
2
2
4
6
2
2
4
6
Wheel fixed
940240
Screw
Washer
Connector 6-pol
Nut blind rivet
950411
Wheel turnable
Screw
940162
940306
911006
940044
Screw
Screw
Socketscrew
950271
16 10 10 10 940057
17
4
4
4
940005
11-8
l
Accessories
Download from Www.Somanuals.com. All Manuals Search And Download.
S E C T I O N
1 2
Transport and Storage
General . . . . . . . . . . . . . . . . . . . . . . . . 12-2
Unpacking and Checking . . . . . . . . . . . . . 12-2
Lifting and Transport to Place of Use . . . . . 12-2
Positioning in Place of Use . . . . . . . . . . . . 12-2
Storage . . . . . . . . . . . . . . . . . . . . . . . . 12-3
Long-Term Storage/Conservation . . . . . . . . 12-3
Transport and Storage
l
12-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Transport and storage
General
The machine should be transported by trained personnel.
The machine is delivered packed in protective plastic foil, fixed to a pallet
with straps.
Unpacking and Checking
•
Check that the machine has not been damaged during transport.
NOTE: Report any damage to the forwarding agent.
Do not unpack the machine before it has been transported to where it is
going to be used.
✐
•
•
Check with the delivery note that the delivery is complete.
Lifting and Transport to Place of Use
The machine weighs incl. packaging,
approx. 1036.17 - 1322.77lbs.
(470 - 600 kg). Space
requirements, see Layout,
Section 10 The machine can
be lifted and handled with a fork-lift
truck.
The lower part of the machine has
two openings on the right-hand
side which accommodate a
fork-lift truck.
Drive in a fork-lift truck as far
as possible (until the bends in
the forks touch the machine),
and then lift the machine.
Positioning in Place of Use
See Installation, Section 5.
12-2
l
Transport and Storage
Download from Www.Somanuals.com. All Manuals Search And Download.
Storage
The machine is packed for transport to the place where it is to be used.
On delivery it is protected with Castrol DWX 22 anti-rust oil.
Long-Term Storage/Conservation
•
•
Store the machine in a room with a stable, dry temperature.
Treat the unpainted surfaces of the machine with rust preventer, such as
Castrol DWX 22. DWX 22 will protect the machine up to 12 months. . . . . .
Alternatively, DWX 160 will provide protection for 24 - 36 months.
Transport and Storage
Download from Www.Somanuals.com. All Manuals Search And Download.
l
12-3
12-4
l
Transport and Storage
Download from Www.Somanuals.com. All Manuals Search And Download.
We’re Here to Help
✐
Additional manuals and prints for
your Conair equipment may be
ordered through the Customer
Service or Parts Department for a
nominal fee.
Conair has made the largest investment in customer support in the plastics indus-
try. Our service experts are available to help with any problem you might have
installing and operating your equipment. Your Conair sales representative also
can help analyze the nature of your problem, assuring that it did not result from
misapplication or improper use.
How to Contact Customer Service
To contact Customer Service personnel, call:
From outside the United States, call: 814-437-6861
You can commission Conair service personnel to provide on-site service by con-
tacting the Customer Service Department. Standard rates include an on-site hourly
rate, with a one-day minimum plus expenses.
Before You Call...
If you do have a problem, please complete the following checklist before
calling Conair:
Make sure you have all model, serial and parts list numbers for your particular
equipment. Service personnel will need this information to assist you.
❒
Make sure power is supplied to the equipment.
❒
❒
Make sure that all connectors and wires within and between control systems
and related components have been installed correctly.
Check the troubleshooting guide of this manual for a solution.
❒
❒
Thoroughly examine the instruction manual(s) for associated equipment, especial-
ly controls. Each manual may have its own troubleshooting guide to help you.
Check that the equipment has been operated as described in this manual.
❒
❒
Check accompanying schematic drawings for information on special considerations.
Appendix
l
A-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Equipment Guarantee
Conair guarantees the machinery and equipment on this order, for a period as
defined in the quotation from date of shipment, against defects in material and
workmanship under the normal use and service for which it was recommended
(except for parts that are typically replaced after normal usage, such as filters,
liner plates, etc.). Conair’s guarantee is limited to replacing, at our option, the part
or parts determined by us to be defective after examination. The customer assumes
the cost of transportation of the part or parts to and from the factory.
Performance Warranty
Conair warrants that this equipment will perform at or above the ratings stated in
specific quotations covering the equipment or as detailed in engineering specifica-
tions, provided the equipment is applied, installed, operated and maintained in the
recommended manner as outlined in our quotation or specifications.
Should performance not meet warranted levels, Conair at its discretion will
exercise one of the following options:
• Inspect the equipment and perform alterations or adjustments to satisfy
performance claims. (Charges for such inspections and corrections will be
waived unless failure to meet warranty is due to misapplication, improper
installation, poor maintenance practices or improper operation.)
• Replace the original equipment with other Conair equipment that will meet
original performance claims at no extra cost to the customer.
• Refund the invoiced cost to the customer. Credit is subject to prior notice by the
customer at which time a Return Goods Authorization Number (RGA) will be
issued by Conair’s Service Department. Returned equipment must be well crated
and in proper operating condition, including all parts. Returns must be prepaid.
Purchaser must notify Conair in writing of any claim and provide a customer receipt
and other evidence that a claim is being made.
Warranty Limitations
Except for the Equipment Guarantee and Performance Warranty stated
above, Conair disclaims all other warranties with respect to the equipment,
express or implied, arising by operation of law, course of dealing, usage of
trade or otherwise, including but not limited to the implied warranties of
merchantability and fitness for a particular purpose.
A-2 l Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
|