COLOR MONITOR
Model No : CTL 5xn
Download from Www.Somanuals.com. All Manuals Search And Download.
FEDERAL COMMUNICATIONS COMMISSION RADIO
FREQUENCY INTERFERENCE STATEMENT
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures :
ƒ¡Reorient or relocate the receiving antenna.
ƒ¡Increase the separation between the equipment and receiver.
ƒ¡Connect the equipment to an outlet on a circuit different from that to
which the receiver is connected.
ƒ¡Consult the dealer or an experienced radio, TV technician for help.
CAUTION: Any changes or modifications not expressly approved by the
part responsible for compliance could void the user's authority
to operate the equipment.
CANADIAN DEPARTMENT OF COMMUNICATIONS
COMPLIANCE STATEMENT
This digital apparatus does not exceed the Class A/ Class B (whichever
is applicable) limits for radio noise emissions from digital apparatus set
out in the Radio Interference Regulations of the Canadian Department of
Communications.
Avis de conformité aux normes du Ministère des Communications du
Canada.
Le present appareil numérique n¡eflmet pas de bruits radioélectriques
depassant les limites applicables aux appareils numériques de Class
A/ de Class B (selon le cas) prescrites dans le règlement sur le brouillage
radioélectrique édicte par le ministère des communications du canada.
Download from Www.Somanuals.com. All Manuals Search And Download.
The power cord is used as a main disconnect device. Disconnect the power
cord before servicing.
The outlet must be installed near the monitor and must be easily accessible.
As an ENERGY STAR Partner, Daewoo Electronics Co., Ltd. has determined that
this product meets the Energy Star guidelines for energy efficiency.
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
Introduction
1
2
Product Features
Setup
Installing the Tilt/ Swivel Stand
3
3
Connecting the D-Sub Signal Cable
Connecting to Your Macintosh Computer
Connecting the Power Cord
Power Management System
DDC for Plug & Play
4
4
4
5
5
Operation & Adjustment
Specifications
6
9
Factory Preset Timings
10
11
Troubleshooting
Appendix
Description for D-sub Connector
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
This manual explains how to correctly install, operate and get the
best performance from your monitor. Please read this user's
manual carefully before installing your monitor, then keep it near
your monitor for quick reference.
First, please check that the contents of the carton box corresponds
with the following checklist :
¡ Color monitor
¡ Power cord
¡ Tilt/ swivel stand
¡ User's manual
¡ Warranty Handbook
¡ Warranty Registration Card
If there is any item missing or damaged, please contact your
dealer. Please keep the carton box and packing materials so that
you may properly store or transport your monitor.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
PRODUCT FEATURES
¡ The convenient and user-friendlly on-screen display allows for
easy and accurate adjustments of horizontal and vertical screen
size and position, geometry and screen color.
¡ The monitor supports a safe working environment in strict
compliance with the MPR¥–standard for low emissions.
¡ The monitor complies with the VESA Display Data Channel
(DDC) specification for “Plug & Play” compatibility. Advanced
m icrocircu itry m akes set-u p and configu ration fast and
effortless.
¡ The monitor features Advanced Color Controls for fine-tuning
to meet your own personal tastes or application requirements.
Use the on-screen controls to adjust the color temperature, RB
gain value for the best possible screen color and intensity.
¡ Just activate the higher refresh rates of the monitor to stabilize
the screen and eliminate the annoying flicker that contributes to
eye-strain and headaches.
¡ The “borderless” full-screen display capability works under all
grap hic m od es and p rovid es a larger view ing area than
conventional monitors, giving you a better picture with more
workspace.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP
INSTALLING THE TILT/SWIVEL STAND
1. Ensure that the power to the monitor is off.
2. Set the monitor face down with the underside facing you.
Please be careful so as not to scratch the monitor screen.
3. Align the four hooks on the stand with the guide holes of
bottom chassis of the monitor.
4. Insert the hooks into the guide holes.
5. Slide the tilt/ swivel stand toward the front of the monitor until
the latch locks in position.
6. Turn the monitor and the stand upright.
2
PUSH
1
PUSH
F R O N T
<Removing the tilt/swivel stand>
If you want to remove the tilt/ swivel stand on the monitor, press
the latch and pull the tilt/ swivel stand toward the back of the
monitor. Lift the stand to separate.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING THE D-SUB SIGNAL CABLE
1. Turn off the computer and monitor.
2. Connect the 15 pin D-sub connector to the output port of the
video card in your computer.
3. Tighten the screws of connector.
CONNECTING TO YOUR MACINTOSH COMPUTER
1. Turn off the computer and monitor.
2. Attach the Macintosh cable adapter to the Macintosh video
card.
3. Tighten the screws on the cable adapter.
4. Connect the signal cable provided with your monitor to the
other end of the Macintosh cable adapter.
5. Tighten the screws between the Macintosh cable adapter and
the signal cable.
CONNECTING THE POWER CORD
1. Plug the power cord into the AC receptacle located at the back
of the monitor.
2. Plug the other end of the power cord into the AC outlet.
If your power cord is PC to Monitor type, plug the other end of the
power cord into the AC receptacle in the computer.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER MANAGEMENT SYSTEM
If you use the monitor with a computer which complies with the
power saving program, you can set the monitor to go blank when
the system has remained unused for a period of time. To specify
the period or to disable this feature, set the system timeout field
of the computer's system setup program or use special software
for power saving. See the computer user's manual for the details
of using the system setup. While the monitor is in power saving
m od e (blank screen), it consu m es less p ow er than norm al
state;the color of the power LED will indicate the state. To restore
the screen image, press any key of your keyboard or move your
mouse. If the signal cable is connected loosely or disconnected,
the power saving feature will operate.
DISPLAY DATA CHANNEL (DDC) FOR PLUG & PLAY
If you use the monitor with a computer which complies with
DDC1/ 2B of VESA, the Host-Video Card automatically
configures itself without your intervention in a way that best fits
the attached monitor.
The Display Data Channel, DDC, allows the monitor to inform
the host system about configuration information for optimum
use of the monitor . Use of the Video Card utility is not required
to match the resolutions and refresh rates of the monitor and
video card.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION & ADJUSTMENT
–
+
EXIT
ADJUST
SELECT
MENU
: Launch OSD(On-Screen Display) Menus
: Select the next function
MENU
: Select the previous function
: Increase the value of any selected function
: Decrease the value of any selected function
+
–
EXIT
: Exit OSD Menus & Launch OSD Menus, when no OSD
Key Process
MENU
1024X768
60Hz
1024X768
60Hz
CONTRAST
BRIGHTNESS
H.POSITION
H.SIZE
CONTRAST
BRIGHTNESS
H.POSITION
H.SIZE
V.POSITION
V.SIZE
V.POSITION
V.SIZE
50
50
–
+
–
+
Register Value change
Register Value change
MENU
MENU
1024X768
60Hz
1024X768
60Hz
PINCUSHION
PINCUSHION
TRAPEZOID
COLOR TEMP.
R. GAIN
TRAPEZOID
COLOR TEMP.
R. GAIN
B. GAIN
B. GAIN
DEGAUSSING
RECALL
DEGAUSSING
RECALL
50
USER 9300 6550
–
+
–
+
Color Select
Register Value change
EXIT
OSD OFF
6
Download from Www.Somanuals.com. All Manuals Search And Download.
1 . OSD(On -Screen Display) Men u 1
Adjust the contrast of image, the
CONTRAST
difference between light and dark areas
on the screen.
50
50
Adjust the brightness of the entire
display.
BRIGHTNESS
Adjust the position of the display horizontally
(left or right).
H. POSITION
50
Adjust the display width (horizontal size).
H. SIZE
V. POSITION
V. SIZE
50
50
50
Adjust the position of the display vertically
(up or down).
Adjust the display height (vertical size).
7
Download from Www.Somanuals.com. All Manuals Search And Download.
2 . OSD (On -Screen Display) Men u 2
Adjust the left and right margins for more
convex or more concave margins.
PINCUSHION
+
ƒUImage turns to
ƒUImage turns to
by
by
.
.
50
50
–
Adjust the trapezoid of the screen by moving
the lines inward or outward.
TRAPEZOID
+
ƒUImage turns to
ƒUImage turns to
by
by
.
.
–
Choose different preset color temperatures or
set your own customized color parameters.
COLOR TEMP.
USER
9300
6550
Adjust the red gain.
R. GAIN
50
50
Adjust the blue gain.
B. GAIN
Degauss the display and restore image quality
DEGAUSSING
NO YES
Reset the screen to the Factory Preset Display
settings.
RECALL
YES
NO
8
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Picture Tube
Type :15-inch, Flat Square Tube type
(14-inch, viewing area)
Dot Pitch : 0.28mm, MPR ¥–
Face Treatment: Non-glare/ Anti-static
Video
Input Signal : R.G.B Analog
Amp. Bandwidth : 60 MHz
Input Sync : TTL, separate negative/ positive
Scan Frequency
Horizontal : 30 - 54 KHz
Vertical : 50 - 120 Hz
Max. Resolution
Power Source
Display Area
1024 dots¡¿768 lines. (at 60 Hz)
Free Voltage (100-240 Vac, 50/ 60Hz )
Standard Display Area :
264mm(H)¡¿198mm(V)
Full Screen Size :284mm(H)¡¿212mm(V)
Power Consumption Max. 80W
State
Recovery Time Power LED
On
None
Green
Stand-by
Suspend
Green:0.5second
Amber:0.5second
3 seconds
Sleep
Off
-
-
Amber
Off
Regulatory Approvals
Safety
EMI
: UL, CSA, DHHS
: FCC-B
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Tilt /Swivel Range Tilt : 5¡£forward, 10¡£backward
Swivel : ¡ 45¡£leftward, rightward
Dimension
368(W)¡¿394(D)¡¿382(H)mm
(set with stand)
Weight (net/Gross) 27.6/ 31.4 lbs
12.5/ 14.2Kg
Operating Environment
Temperature : 10~4˚C/ 50~104˚F
Relative Humidity : 8~80%
Storage Environment
Temperature : -20~45˚C/ -68~113˚F
Relative Humidity : 5~90%
FACTORY PRESET TIMINGS
Resolution
Mode
VGA
H.Freq (KHz)
V. Freq (Hz)
Remark
(dots¡¿lines)
720¡¿400
640¡¿480
640¡¿480
800¡¿600
1024¡¿768
800¡¿600
31.5
31.5
37.5
46.9
48.4
53.7
70
60
75
75
60
85
Non-interlaced
Non-interlaced
Non-interlaced
Non-interlaced
Non-interlaced
Non-interlaced
VGA
VESA VGA 75
VESA 46K
VESA 1024/ 60
VESA 800x600 @85Hz
This monitor has stored above-mentioned six timings in factory. You
can save up to 10 modes in the user memory automatically. Please note
that if you save to user memory over ten times, the first mode saved
will be replaced with your eleventh mode.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Symptom
Check
No picture.
Check if POWER SWITCH and COMPUTER
POWER SWITCH are in the on position.
‹q
Check if the signal cable is correctly connected to
the video card.
‹q
Check if the pins of D-sub connector are not bent.
‹q
Check if the computer is in the power saving mode.
POWER LED is not lit. Check if POWER SWITCH is in the on position.
‹q
Check if the power cord is correctly connected.
Image is unstable.
Check if the signal cable is suitable to the video card.
Image is not centered,
too small, or too large.
Adjust H&V SIZE or H&V POSITION to get the
proper image.
Picture bounces
or a wave pattern
is present in the
picture.
Keep the devices that may cause electrical interference
away from the monitor.
‹q
See the FCC information at the front cover of the manual.
Color looks
blotchy.
Operate DEGAUSSING once.
Picture is blurred.
Adjust CONTRAST and BRIGHTNESS.
‹q
Operate DEGAUSSING once.
Edges of available
area on the screen
are not straight.
Adjust PINCUSHION / TRAPEZOID .
11
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
DESCRIPTION FOR D-SUB CONNECTOR
Pin
Signal
1
1
2
Red
Green
3
4
5
6
Blue
GND
GND (Self -Test)
GND - Red
6
10
15
7
8
GND - Green
GND - Blue
9
No Pin
10
11
12
13
14
15
GND - H.Sync
GND-V.Sync
Bi-directional Data (SDA)
Horizontal Sync
Vertical Sync (VCLK)
Data Clock (SCL)
*GND = Ground
Download from Www.Somanuals.com. All Manuals Search And Download.
S/N: 9978623903
Download from Www.Somanuals.com. All Manuals Search And Download.
|