EZ-LP Quick Start Guide
“Keep Your Code. Choose Your Printer.”
CognitiveTPG Headquarters
25 Tri-State International, Suite 200, Lincolnshire, IL 60069
Toll Free: 800-732-8950 Phone: 847-383-7900 Fax: 847-383-7949
Copyright 2009 CognitiveTPG. All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
L1oading Media:
2
5
8
3
6
Outward Wound
Inward Wound
4
9
7
Click!
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Data Cable:
USB
COM/SER
I O I O
Power OFF
Power OFF
Serial
(DB9)
USB-B
(Device)
ETHERNET
PARALLEL
Parallel
(Centronics)
Power OFF
Power OFF
Ethernet
Ferrite Bead
(Install on Parallel Cable as Shown)
Self-Testing:
2
4
1
2
ON
1
Press FEED button while powering up
Release FEED button when printing begins
3
OFF
ON
Power OFF to end test mode
Power ON for normal operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the EZ-LP:
1. Identify the current printer being replaced and determine whether it is using EPL or ZPL as the programming
language. You may need to refer to this information during the set-up process depending on the method you
choose.
Note: The EZ-LP ships with the default language emulation set to AUTO which means it will automatically set the
language to EcPL for EPL emulation and ZcPL for ZPL emulation.
2. In order to change printer settings you can download the CognitiveTPG Printer Administrator utility (see
Downloading CognitiveTPG Printer Administrator) or to make changes without downloading a software utility,
consult the EZ-LP User’s Guide.
Downloading CognitiveTPG Printer Administrator
In order to easily make printer configuration changes install the CognitiveTPG Printer Administrator utility. Follow the
for the EZ-LP printer. You can also follow this path: http://www.CognitiveTPG.com > Downloads > Utility. This process
will also install Windows drivers for the printer on your computer. Note that USB, Ser/Com, or Ethernet connection is
required for configuring your EZ-LP printer via this utility.
Download from Www.Somanuals.com. All Manuals Search And Download.
Add Printer as a Replacement for Legacy Printer
Note: Default setting for Ser/Com is 9600 baud, 8 bit word length, no parity, 1 stop bit. Default setting for network
communications (Ethernet) is DHCP ON.
1. Print configuration label or record your current printer’s settings, including the driver port setting
2. Power off your current desktop label printer and disconnect the communication cable
3. Connect Power supply to EZ-LP and plug into wall. Do NOT turn on EZ-LP at this time
4. Connect preferred interface cable to EZ-LP and connect to PC
5. Turn on the EZ-LP printer
6. If using USB connection a New Hardware Wizard may appear on screen. Click on “Cancel”; continue with the
next step 9 below. If using Ser/Com, Parallel or Ethernet connection continue with the next step below
7. Print from your application, you are finished. If you need to make adjustments see the beginning of this
section, Printer Installation, for your options
8. If you wish to add the EZ-LP and assign it to an existing driver, please continue.
9. In Microsoft Windows click START > Printers and Faxes > Add printer and follow the Add Printer Wizard
10. In the Welcome to the Add Printer Wizard window, click “Next”
11. In the Local or Network Printer window, choose “Local printer attached to this computer”and click “Next”
12. In the Select a Printer Port window, click on the drop down arrow to select your port and click “Next”
13. Next you will see the Install Printer Software window, this step assigns a particular printer driver to the printer.
The EZ-LP can use ZPL and EPL printer drivers for printing. Scroll down to choose the manufacturer of the
printer you are replacing then choose its model number in the “Printers”box, click “Next”
14. In the Use Existing Drivers window, choose “Keep existing driver (recommended)”and click “Next”
15. In the Name Your Printer window, type “EZ-LP”or the designation of your choice in the “Printer name:”field,
click “Next”
16. In the Printer Sharing window, choose the option you desire “Do not share this printer”is the default, click
“Next”
17. In the Print Test Page window, leave on “Yes”if desired, note that the test page will not print until the Add
Printer Wizard is finished, click “Next”
18. In the Completing the Add Printer Wizard window, click “Finish”
USB Plug and Play Note: if you did not install CognitiveTPG Printer Administrator and CognitiveTPG drivers you will see
a pop-up Add Hardware Wizard window on your PC every time power is cycled on the printer or the PC. You may click
on “cancel”and continue working or you may follow the Downloading CognitiveTPG Printer Administrator instructions
above to prevent this pop-up from occurring. You may continue to print using the original EPL or ZPL printer driver.
Download from Www.Somanuals.com. All Manuals Search And Download.
The EZ-LP ships with the following default settings:
Parameter
Default Setting
Programming Language
Speed
Auto (automatically detects and sets to EcPL or ZcPL)
5 ips (127 mm/s)
Label Width
432 (4.32 inches or 110 mm)
Label Length
Measure label (automatically measures and sets label
length at power up)
Indexing Type
Gap
Reference Point
0,0 (upper left corner)
On
Auto Top of Form
Enable Label Present
Advance Label
On
25 (0.25”or 6.4 mm)
25 (0.25”or 6.4 mm)
0 seconds
Retract Label
Delay Time (Retract Label)
Serial Port Settings
(serial port printers only)
9600 bps, 8 bit data, 1 stop bit, no parity
(DCE configuration - use straight-through cable)
Settings below only apply to printers with Ethernet
Printer IP Address
Net Mask
Gateway
10.0.0.12
0.0.0.0
0.0.0.0
On
DHCP
LPD
On
RTEL
On
RTEL Port Number
9100
Warranty Information:
and click on Warranty Registration.
Helpful Information:
To learn more about CognitiveTPG printers and approved media, please contact
your local reseller or CognitiveTPG:
Website: www.CognitiveTPG.com
Direct: +1.847.383.7900
Toll Free: +800.732.8950
For technical support, please call 607-274-2505.
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning – Shock Hazard and Static Discharge
Never operate the printer in a location where it can get wet. Personal injury could result. The discharge of electrostatic energy that accumulates on the surface
of the human body or other surfaces can damage or destroy the printhead or electronic components used in this device. DO NOT TOUCH the printhead or the
electronic components under the printhead carriage.
Caution – Printer Setup and Handling
When installing or modifying the printer setup or configuration, ALWAYS TURN THE POWER OFF before: (1) connecting any cables, (2) performing any cleaning or
maintenance operations, or (3) moving the printer.
European Compliance
This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
RoHS COMPLIANCE: 2002/95/EC on the Restriction of the Use of certain Hazardous Substances in Electrical and Electronic Equipment (RoHS).
WEEE:
Directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE). For WEEE recycling and recovery information, refer to the CognitiveTPG Web site.
Federal Communications Commission (FCC) Radio Frequency Interference Statement Warning
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
Information to the User
This equipment must be installed and used in strict accordance with the manufacturer’s instructions. However, there is no guarantee that interference to
radio communications will not occur in a particular commercial installation. If this equipment does cause interference, which can be determined by turning
the equipment off and on, the user is encouraged to contact CognitiveTPG, Inc. immediately. CognitiveTPG, Inc. is not responsible for any radio or television
interference caused by unauthorized modification of this equipment or the substitution or attachment of connecting cables and equipment other than those
specified by CognitiveTPG, Inc. The correction of interferences caused by such unauthorized modification, substitution or attachment will be the responsibility
of the user. In order to ensure compliance with the Product Safety, FCC and CE marking requirements, you must use the power supply, power cord, and interface
cable which are sold for use with this product or which meet the following parameters:
This product has been tested for Safety and EMC Compliance as indicated below and is intended for use only with the Power Supply and cables included. If using
the parallel interface, please add the enclosed clamp-on ferrite to the parallel cable being used and secure it in place with the cable ties supplied.
Industry Canada (IC) Radio Frequency Interference Statement
This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
DECLARATION OF CONFORMITY
Type of Equipment: Information Technology Equipment – Printer
Model: DBDXX-XXXX-XXXX
Model: DBTXX-XXXX-XXXX (X = any alphanumeric character)
Applicable EU Directives:
2004/108/EC (electromagnetic compatibility directive)
2006/95/EC (low voltage directive for product safety)
Harmonized Standards:
EN 55024 (1998/A1:2001/A2:2003) Information Technology Equipment Immunity Characteristics
EN 55022 (1998/A1:2001/A2:2003) EMC, Class A, Limits and Methods of Measurement of Interference
Characteristics of IT Equipment
IEC 60950-1 (2005) Second Edition - Product Safety Standard.
“TPG IPB, Inc., 950 Danby Road, Ithaca, New York, 14850, declares that the equipment specified
above conforms to the referenced EU Directives and Harmonized Standards.”
Date: Feb 6, 2009
Randy Bullock, Regulatory Compliance Engineer , CognitiveTPG and TPG IPB
Ref #: 189-1300070 Rev B
Copyright 2009 CognitiveTPG. CognitiveTPG and EZ-LP are trademarks of CognitiveTPG. Other products and corporate
names used in this publication may be trademarks or registered trademarks of other companies and are used only for
explanation and to their owner’s benefit, without intent to infringe. No part of this guide may be reproduced for any
purpose or in any form, including electronic storage and retrieval without the express permission of CognitiveTPG.
CognitiveTPG Headquarters
25 Tri-State International, Suite 200, Lincolnshire, IL 60069
Toll Free: 800-732-8950 Phone: 847-383-7900 Fax: 847-383-7949
EZLP-QSG0000 Rev. B 2009
Copyright 2009 CognitiveTPG. All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
|