Cisco Systems IP Phone OL 20862 01 User Manual

C H A P T E R  
5
Setting Up the Cisco Unified Video Camera  
The Cisco Unified IP Phone 9951 and 9971 supports the add-on accessory Cisco Unified Video Camera.  
The Cisco Unified Video Camera connects to your Cisco Unified IP Phone and allows you to make a  
point-to-point video call with another Cisco Unified IP Phone with a Cisco Unified Video Camera  
attached. If a phone does not have a Cisco Unified Video Camera attached, it can only receive one-way  
video.  
This chapter contains the following information:  
Configuring the Cisco Unified Video Camera  
To configure the Cisco Unified Video Camera, you must perform the following configuration steps in  
Cisco Unified Communications Manager administration:  
Note  
The parameters described in the following procedure can be enabled on either the Phone Configuration  
window (Device > Phone), the Enterprise Phone Configuration window (System > Enterprise Phone  
Configuration), or the Common Phone Profile window (Device > Device Settings > Common Phone  
Profile). Be sure to also check the corresponding Override Common Settings parameter in the  
configuration window. The Phone Configuration window is referenced below for purposes of the  
procedure description.  
For more information about parameters that can be configured in any of these three configuration  
windows, see the “Configuring Product Specific Configuration Parameters” section on page 8-20.  
Procedure  
Step 1  
In the phone configuration window (Device > Phone) of the phone to which you are adding the Cisco  
Unified Video Camera, enable the Cisco Camera parameter. This field is located in the Product Specific  
Configuration layout portion of the window.  
Cisco Unified IP Phone 8961, 9951, and 9971 Administration Guide for Cisco Unified Communications Manager 8.0 (SIP)  
OL-20862-01  
5-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Chapter 5 Setting Up the Cisco Unified Video Camera  
Adjusting the Camera Settings  
Step 3  
Step 4  
Step 5  
Step 6  
Step 7  
Highlight Cisco Unified Camera.  
Press the Set-up softkey.  
Select View Area.  
Use the arrows on the Navigation pad to increase or decrease the view area.  
Press the Save softkey.  
Adjusting the Brightness Setting  
The Brightness setting affects the video that you transmit to others. However, it does not affect the video  
that you receive from other parties. You can adjust the brightness setting to improve the quality of the  
video during streaming.  
Note  
As the field of view can affect brightness, adjust the View Area feature for your camera before adjusting  
the Brightness setting.  
To adjust the Brightness setting, follow these steps:  
Procedure  
Step 1  
Step 2  
Step 3  
Step 4  
Step 5  
Step 6  
Step 7  
On the Cisco Unified IP Phone, press the Applications button  
Select Accessories.  
.
Highlight Cisco Unified Camera.  
Press the Set-up softkey.  
Select Brightness.  
Use the arrows on the Navigation pad to increase or decrease brightness.  
Press the Save softkey.  
Adjusting Auto Transmit Setting  
The Auto Transmit feature allows you to control the streaming of videos for both inound and outbound  
calls.  
When Auto Transmit is on (default setting), the camera streams video automatically during calls.  
When Auto Transmit is off, video for each call is automatically muted (however, your phone still  
receives video). To resume video transmission in this case, press the Unmute Video softkey  
.
To turn the Auto Transmit setting on or off, follow these steps:  
Procedure  
Step 1  
On the Cisco Unified IP Phone, press the Applications button  
.
Cisco Unified IP Phone 8961, 9951, and 9971 Administration Guide for Cisco Unified Communications Manager 8.0 (SIP)  
OL-20862-01  
5-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Chapter 5 Setting Up the Cisco Unified Video Camera  
Post-Installation Steps  
Step 2  
Step 3  
Step 4  
Step 5  
Select Accessories.  
Highlight Cisco Unified Camera.  
Press the Set-up softkey.  
Press the Turn On or Turn Off softkey.  
Post-Installation Steps  
After installing the Cisco Unified Video Camera, perform the following checks:  
1. Wait till the “camera ready” message appears.  
Note  
The camera may need to upgrade after installation. This may take a few minutes before the  
camera is operational.  
2. Press the Video Preview softkey to check the picture quality.  
If the video preview image looks too blue, try increasing the camera Brightness setting.  
If the background looks washed out, try decreasing the camera Brightness setting.  
Note  
For information about adjusting camera settings on the phone, see the Cisco Unified Video  
Camera Quick Start Guide at this location:  
3. Move the phone/camera to a position where there are no bright lights in the field of view.  
4. Move the phone/camera so that the user is illuminated by light coming from the front.  
Using the Cisco Unified Video Camera  
For information about placing and receiving video calls, setting up video conferences, and adjusting  
camera settings on the phone, see the Cisco Unified Video Camera Quick Start Guide at this location:  
Cisco Unified IP Phone 8961, 9951, and 9971 Administration Guide for Cisco Unified Communications Manager 8.0 (SIP)  
OL-20862-01  
5-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   

Berkel Food Processor M2000 115V 1 2 HP User Manual
Black Decker Cordless Drill 90504019 User Manual
Blodgett Oven MT3255G User Manual
BMW Car Stereo System CD43 User Manual
Bosch Appliances Home Security System MIC WKT User Manual
Brookstone Speaker System WIRELESS BLUETOOTH SPEAKER User Manual
Brother Fax Machine 1840C User Manual
Brother Sewing Machine CE 500PRW User Manual
Capresso Espresso Maker Impressa F7 User Manual
Chauvet Projector DMX5F User Manual