I N S T A L L A T I O N I N S T R U C T I O N S
Instrucciones de instalación
Installationsanleitung
Istruzioni di installazione
Installatie-instructies
Instruções de Instalação
Instructions d´installation
XSM
XTM
FUSION EXTRA LARGE HEIGHT ADJUST
FLAT PANEL MOUNTS
XSM/XTM Series
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
XSM/XTM Series
DIMENSIONS
XSM
MAX MOUNTING PATTERN IS 46" (1168.4 mm) WITHOUT REVERSING UPRIGHTS
WITH REVERSING THE UPRIGHTS
MAX MOUNTING PATTERN IS 48.4" (1229.4 mm)
0
10.2
45
.40
12.9
.51
1.77
90
3.54
105
4.13
24.3
MINIMUM UPRIG HT SPAC ING
38.4
1.51
150
5.91
165
6.50
24"
.96
25.4
1.00
73.9
2.91
210
8.27
225
8.86
8.3
.33
270
10.63
285
11.22
51
2
383.4
15.10
44.5
1.75
685.8
27.00
330
12.99
419.6
16.52
345
13.58
405
RAILS CAN BE SLID LEFT
15.94
OR RIGHT FOR OFFSET
25.4
1.00
465
18.31
525
1232.7
48.53
20.67
585
23.03
630
24.80
660
25.98
MEASUREMENTS IN: [MILLIMETERS]
INCHES
XTM
WITH REVERSING THE UPRIGHTS
MAX MOUNTING PATTERN IS 49.2" (1249.7 mm)
10.2
.40
12.9
.51
0
45
1.77
12°
MINIMUM UPRIG HT SPAC ING
MAX TILT WILL VARY DEPENDING
UPON SC REEN SIZE
90
3.54
24"
24.4
.96
25.4
1.00
105
50.8
2.00
4.13
74.1
2.92
150
5.91
165
6.50
210
8.27
25.4
1.00
8.3
.33
225
8.86
270
10.63
285
11.22
44.5
1.75
419.6
16.52
383.4
15.10
685.8
27.00
670.8
26.41
330
12.99
345
13.58
RAILS CAN BE SLID LEFT
OR RIGHT FOR OFFSET
405
15.94
465
18.31
525
20.67
1232.8
48.54
585
23.03
630
24.80
660
25.98
MEASUREMENTS IN: [MILLIMETERS]
INCHES
3
Download from Www.Somanuals.com. All Manuals Search And Download.
XSM/XTM Series
Installation Instructions
LEGEND
Tighten Fastener
Pencil Mark
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Potloodmerkteken
Marquage au crayon
Loosen Fastener
Drill Hole
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Percez un trou
Phillips Screwdriver
Adjust
Destornillador Phillips
Ajustar
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Remove
Quitar
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Clé à fourche
By Hand
Optional
Opcional
Optional
Opcional
Opzionale
Optie
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
En option
Hex-Head Wrench
Security Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
Zeskantsleutel
Clé à tête hexagonale
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
XSM/XTM Series
TOOLS REQUIRED FOR INSTALLATION
#2
7/32" (5.5mm) Wood Stud
5/16" (7.9mm) Concrete
PARTS
B (1)
C (1)
A (1)
[Included with
XSM2XXX/XTM2XXX
(XTM Only)
J (1) [Used on XSMU/XTMU Models Only]
Models Only]
E (1)
Custom
XSM2XXX/
XTM2XXX
Hardware
J2 (6)
M6x25mm
J1 (6)
M6x16mm
G (1)
F (1)
J3 (6)
J4 (6)
M8x20mm
M8x30mm
(XSM Only)
J6 (6)
J5 (4)
M8x50mm
M10x40mm
H (4)
K (1)
J7 (6)
M10x50mm
J8 (6)
M6
J9 (6)
M8
L (1)
K1 (4)
5/16"
K2 (4)
5/16"
J10 (6)
1.00x.400x.75"
J11 (6)
.750x.323x.250"
K3 (4)
5/16" x 2-1/2"
J12 (1)
M5
J13 (1)
M6
5
Download from Www.Somanuals.com. All Manuals Search And Download.
XSM/XTM Series
Installation Instructions
INSTALLATION
Center of screen
The XTM and XSM have been designed to be mounted directly
onto either a wood stud or concrete wall. The XTM has brackets
which allow the display to be tilted. The XSM has static brackets
which keep the display in an upright position.
7-1/2"
Locate Mounting Site
WARNING: IMPROPER INSTALLATION CAN LEAD TO
MOUNT FALLING CAUSING SEVERE PERSONAL INJURY
OR DAMAGE TO EQUIPMENT! It is the installers
responsibility to make certain the structure to which the
mount is being attached is capable of supporting five times
the weight of the XTM or XSM and all attached equipment not
to exceed 250 lbs (113.4 kg).
Vertical center
of mount
NOTE: Proceed to either the Installing to a Wood Stud Wall
section or the Installing to a Concrete Wall section.
Installing to a Wood Stud Wall
CAUTION: MINIMUM HORIZONTAL DISTANCE
BETWEEN WALL BRACKETS IS 24". Do not place mounting
brackets closer together than 24". When attaching to a wall
containing studs located 16" on center, space the uprights
32" apart.
Figure 1
5. Using a level, mark the wall on each stud to attach the
mount through the upper mounting slots. (See Figure 2)
1. Determine the center of the display, and where it should be
located on the wall.
WARNING: ELECTRICAL SHOCK HAZARD! CUTTING
OR DRILLING INTO ELECTRICAL CORDS OR CABLES
CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY!
ALWAYS make certain area behind mounting surface is free
of electrical wires and cables before drilling or installing
fasteners.
2. Locate the appropriate studs to the left and right of the
selected location.
NOTE: If the screen area lies over a stud, use that stud and an
appropriate stud to either the left or right of it.
3. Line up the notches on mount with center of screen marking
to determine vertical center. (See Figure 1)
WARNING: EXPLOSION AND FIRE HAZARD! CUTTING
OR DRILLING INTO GAS PLUMBING CAN CAUSE DEATH
OR SERIOUS PERSONAL INJURY! ALWAYS make certain
area behind mounting surface is free of gas, water, waste, or
any other plumbing before cutting, drilling, or installing
fasteners.
4. Measure up 7-1/2" from the center point to mark location of
the upper mounting slots.
6. Drill one 7/32" pilot hole in each stud.
7. Use two 5/16 x 2-1/2" lag bolts (K3) and two 5/16" flat
washers (K2) to attach top of mount to wall. (See Figure 2)
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
XSM/XTM Series
WARNING: EXPLOSION AND FIRE HAZARD! CUTTING
OR DRILLING INTO GAS PLUMBING CAN CAUSE DEATH
OR SERIOUS PERSONAL INJURY! ALWAYS make certain
area behind mounting surface is free of gas, water, waste, or
any other plumbing before cutting, drilling, or installing
fasteners.
6
5
8
9
4
5
(K1) x 4
6 10
x4
7
(K3) x 4
10
8
9
(K2) x 4
Figure 2
8. Mark the attachment points for the lower mounting slots,
making sure the attachment points are located on the studs.
(See Figure 2)
(K3) x 4
7 11
(K2) x 4
9. Drill 7/32" pilot holes at markings for lower mounting holes.
(See Figure 2)
10. Use two 5/16 x 2-1/2" lag bolts (K3) and two 5/16" flat
washers (K2) to attach the mount to the wall through the
lower mounting holes. (See Figure 2)
Figure 3
5. Drill one 5/16" pilot hole at each marking.
11. Slide rails to approximate center of screen location.
6. Install an anchor (K1) into each pilot hole using a hammer.
Installing to a Concrete Wall
7. Use two 5/16 x 2-1/2" lag bolts (K3) and two 5/16" flat
washers (K2) to attach top of mount to anchors in wall.
8. Mark the attachment points for the lower mounting slots.
(See Figure 3)
9. Drill one pilot hole at each marking for lower mounting
holes. (See Figure 3)
CAUTION: MINIMUM HORIZONTAL DISTANCE
BETWEEN WALL BRACKETS IS 24". Do not place mounting
brackets closer together than 24".
1. Determine the center of the display, and where it should be
located on the wall.
10. Install an anchor (K1) into each pilot hole using a hammer.
11. Use two 5/16 x 2-1/2" lag bolts (K3) and two 5/16" flat
washers (K2) to attach the mount to the wall through the
lower mounting holes. (See Figure 3)
2. Line up the notches on mount with center of screen marking
to determine vertical center. (See Figure 1)
3. Measure up 7-1/2" from the center point to mark location of
the upper mounting slots. (See Figure 1)
12. Slide rails to approximate center of screen location.
Attaching Interface Brackets to Display
4. Using a level, mark the wall through both upper mounting
slots. (See Figure 3)
1. Align the center of the bracket with center of screen.
(See Figure 4)
NOTE: The diamond-shape hole in the bracket corresponds to
WARNING: ELECTRICAL SHOCK HAZARD! CUTTING
OR DRILLING INTO ELECTRICAL CORDS OR CABLES
CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY!
ALWAYS make certain area behind mounting surface is free
of electrical wires and cables before drilling or installing
fasteners.
the center of the mount.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
XSM/XTM Series
Installation Instructions
1
Knobs
Center of bracket
Figure 4
WARNING: IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Using screws of
improper size may damage your display. Properly sized
screws will easily and completely thread into display
mounting holes. If spacers are required, be sure to use longer
screws of the same diameter.
2
Figure 5
2. Select correct screws, spacers (if necessary) and washers
from the hardware bag and attach brackets to back of
screen. (See Figure 4)
3. If necessary, the tilt interface bracket knobs may be
switched to allow the interface brackets to be reversed.
(See Figure 6)
Switching Interface Brackets (Optional)
a. Remove display from mount.
b. Remove interface brackets from display.
c. Hold the right interface bracket horizontally, tightly
gripping it so that spacers do not move.
d. Remove the knob, washer and screw.
If an installation situation makes adjusting the location of
interface brackets necessary, there are several options.
1. The wall brackets may be adjusted side to side at the point
of attachment. (See Figure 5)
2. The location of the left and right interface brackets may be
switched, with the knobs on the XTM interface brackets
facing the inside of the mount. (See Figure 5)
e. Replace the knob, washer and screw in the opposite
order, with the knob on the inside of the bracket.
f. Switch the right interface bracket to the left side of the
wall mount.
g. Repeat Steps 3c through 3f with the left interface
bracket.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
XSM/XTM Series
Center Line (CL)
3d
3e
Pull strap
NEVER place both interface brackets to one
side of the wall mount center line (CL)!
Knobs to outside
of brackets
Figure 6
Attaching Screen to Wall Mount
1. Attach wall bracket caps (H) to top and bottom of both wall
brackets. (See Figure 7)
Both interface brackets must NEVER be located
to one side of the wall brackets!
Figure 8
XTM Model
NOTE: Proceed to Step 8 for XSM Model instructions.
3. Hang top hook of interface brackets onto the top bar of the
mount. (See Figure 9)
(H) x 4
NOTE: The screen initially installs into the "kickstand mode" to
allow easy cable access.
Figure 7
4. Slide screen and bars to desired viewing position.
5. Route cables between wall and bars.
2. Adjust Velcro® pull strap (if necessary) so it does not
extend beyond bottom of screen. (See Figure 8)
NOTE: NEVER place both interface brackets to one side of the
wall mount center line! (See Figure 8)
CAUTION: PINCH POINTS! Keep fingers, hands and
cables out of pinch point areas.
NOTE: Do NOT allow both interface brackets to be located on
same side of wall bracket. (See Figure 8)
6. Pull downward on the pullstraps and swing inward toward
wall, latching interface brackets to lower bar and locking
bottom of screen to the mount. (See Figure 9)
9
Download from Www.Somanuals.com. All Manuals Search And Download.
XSM/XTM Series
Installation Instructions
7. Proceed to Adjusting Roll/Height of Wall Brackets
10. Move screen towards the wall by pulling display bottom
away from wall and pushing the interface bracket tabs up
one notch to the detent which you will be able to feel
(approximately half way up).
section.
11. Push bottom of display toward the wall bracket so that lower
latch on interface bracket surrounds lower bar of wall
mount.
(Screen not shown for clarity)
Top
Hook
12. Raise interface brackets tabs all the way to secure the
brackets onto the wall mount. (See Figure 10)
3
Adjusting Roll/Height of Wall Brackets
NOTE: The height adjust wall brackets allow adjustment of
+ 1/2".
1. Turn to right (tighten) to raise side of screen.
(See Figure 11)
2. Turn to left (loosen) to lower side of the screen.
1
Raises screen
Lowers screen
2
(G)
6
Pull straps
Figure 9
XSM Model
(Screen not shown for clarity)
8. Push interface bracket tab all the way down so that the
lower mounting slot is blocked. (See Figure 10)
Figure 11
Locking XTM Mount (Optional)
Latch
closed
1. Add optional security bracket (L) to the mount.
(See Figure 12)
2. Add padlock (not included) to complete security.
(XTM Shown)
Latch
open
(L)
Interface
bracket
tab
1
2
12
8
10
Figure 10
9. Hang the top hook of interface brackets onto the top bar of
the mount. The bottom of the screen will be away from the
wall.
Figure 12
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
XSM/XTM Series
Locking XSM Mount (Optional)
Add padlock (not included) to interface bracket tab to lock the
XSM mount. (See Figure 13)
Add padlock
Figure 13
11
Download from Www.Somanuals.com. All Manuals Search And Download.
XSM/XTM Series
Installation Instructions
USA/International
Europe
A
P
F
A
P
F
8401 Eagle Creek Parkway, Savage, MN 55378
800.582.6480 / 952.894.6280
877.894.6918 / 952.894.6918
Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
+31 (0)40 2668620
+31 (0)40 2668615
Chief Manufacturing, a products
Asia Pacific
A
Room 24F, Block D, Lily YinDu International Building
LuoGang, BuJi Town, Shenzhen, CHINA.
division of Milestone AV Technologies
8805-000259
P
F
+86-755-8996 9226
+86-755-8996 9217
¤2008 Milestone AV Technologies,
a Duchossois Group Company
11/08
Download from Www.Somanuals.com. All Manuals Search And Download.
|