I N S T A L L A T I O N I N S T R U C T I O N S
Display Carts
MFC, PFC Series
Download from Www.Somanuals.com. All Manuals Search And Download.
MFC, PFC Series
Installation Instructions
DIMENSIONS
MFC
PFC
[177]
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
MFC, PFC Series
LEGEND
Tighten Fastener
Pencil Mark
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Marquage au crayon
Loosen Fastener
Drill Hole
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Percez un trou
Phillips Screwdriver
Adjust
Destornillador Phillips
Ajustar
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Remove
Quitar
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Clé à fourche
By Hand
Optional
Opcional
Optional
Opcional
Opzionale
Optie
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
En option
Hex-Head Wrench
Security Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
Zeskantsleutel
Clé à tête hexagonale
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
MFC, PFC Series
TOOLS REQUIRED FOR INSTALLATION
3/16"
(Included)
PARTS
B (1)
(right)
A (1)
(left)
D (4)
E (1)
C (2)
F (1)
J (1)
3/16"
G (1)
PFC
Only
H (1)
MFC
Only
N (4)
5/16-18 x 4-1/4"
P (4)
5/16"
L (4)
5/16-18 x 3/4"
M (4)
5/16-18 x 2-3/4"
K (1)
3/16"
5
Download from Www.Somanuals.com. All Manuals Search And Download.
MFC, PFC Series
Installation Instructions
2. Attach center post (E) to leg assembly using four 5/16-18 x
2-3/4" button head cap screws (M) and four 5/16" washers
(P). (See Figures 2 and 3)
ASSEMBLY
(E)
CAUTION: Attachment holes may be damaged if a power
drill is used to insert button head cap screws. Screws should
first be inserted and turned BY HAND with the hex key or with
a handheld screwdriver BEFORE using the hex head drill bit
and power drill to complete the attachment.
Assembling Cart
1. Assemble two legs (A) and (B) to the cart cross bracket (F)
using two 5/16-18x4-1/4" button head cap screws (N) per
leg. (See Figure 1)
(N) x 4
(M) x 4
(P) x 4
(Front view of cart)
Figure 3
(A)
(F)
3. Attach head assembly (G) or (H) to the cart assembly using
four 5/16-18 x 3/4" button head cap screws (L).
(See Figure 4)
(L) x 4
(C) x 2
(B)
(Front view of cart)
Figure 1
CAUTION: Attachment holes may be damaged if a power
drill is used to insert button head cap screws. Screws should
first be inserted and turned BY HAND with the hex key or with
a handheld screwdriver BEFORE using the hex head drill bit
(J) and power drill to complete the attachment.
NOTE: Insert and turn screws in order shown (1, 2, 3, 4) in
Figure 2.
(G)
(or H)
(E)
1
(PFC Shown)
4
3
(Back view of cart)
2
Figure 4
(Bottom view of cart)
Figure 2
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
MFC, PFC Series
Attaching Display to Cart
WARNING: EXCEEDING MAXIMUM WEIGHT CAPACITY
MAY LEAD TO SERIOUS PERSONAL INJURY OR
DAMAGE TO EQUIPMENT! It is the installer’s responsibility
to ensure the total amount of weight placed on the cart does
not exceed 125 lbs (56.70 kg) for the MFC, and 200 lbs
(90.72 kg) for the PFC.
5
CAUTION: Before attaching display to cart set the brakes
on the back wheels by pressing down on the tab.
(See Figure 5)
Press down to
set brakes
Figure 7
WARNING: DISPLAY MAY WEIGH IN EXCESS OF 40
LBS! Always use two people and proper lifting techniques
when installing or positioning display on cart.
5. Lower display into place listening for audible "click" to
ensure recessed area of mounting buttons are properly
seated in lower area of mounting holes. (See Figures 7 & 8)
Figure 5
WARNING: IMPROPER INSTALLATION CAN LEAD TO
CART OR DISPLAY FALLING CAUSING SERIOUS
PERSONAL INJURY OR DAMAGE TO EQUIPMENT!
Ensure mounting buttons are completely engaged in
mounting holes.
1. Adjust the cart to the desired height by holding the top part
of the post, pulling out knob on the center post and turning
o
90 in either direction to disengage the locking mechanism.
o
2. Raise or lower the center post, then turn the knob 90 either
direction to engage the knob and lock the cart at desired
height. (See Figure 6)
NOTE: Holes are provided in the faceplate for use with a
padlock or similar locking device, if desired. In addition,
the pin and nut may be removed from the upper holes
and moved to the lower holes for use as a more
permanent locking device. (See Figure 8).
Do NOT let
display rest
here
2
1
May remove
pin and nut and
move to lower holes
4
Figure 6
5
IMPORTANT ! : Set the height of the cart so the display
does NOT rest on the lower part of the center post.
(See Figure 6.) Always set the height so the knob is
engaged in a hole in the center post.
A padlock or bolt
may be placed
through latch holes
3. Attach a PSBU or MSBU interface bracket to the display
following the instructions included with the bracket.
4. While supporting both sides of display, align four mounting
buttons on display or interface bracket with four mounting
holes in head assembly. (See Figures 7 and 8)
Figure 8
7
Download from Www.Somanuals.com. All Manuals Search And Download.
MFC, PFC Series
Installation Instructions
Tilting Display
o
(Rear
view of
center post)
The display can be tilted up to 15 either backward or forward
from a straight upright position.
2
(Front view
of center post)
1. Turn knob counterclockwise on back of head assembly to
loosen the tilt. (See Figure 9)
3
1
Exits for
signal cables
3
1
Place optional bolt
(not provided) here
to lock in an upright
Snap-on
covers
4
Exit for
power
cables
position.
(MFC Shown)
Figure 9
o
2. Tilt display as desired, to a maximum of 15 either forward
or backward.
Figure 10
3. Turn knob clockwise to tighten display on head assembly.
(See Figure 9)
Cart Use and Maintenance
CAUTION: Tighten knob on back of head assembly to
prevent damage when moving the cart and display.
CAUTION: This cart is intended for use only with the
products and maximum weights indicated (125 lbs [56.70 kg]
for the MFC, and 200 lbs [90.72 kg] for the PFC). Use with
other products or products heavier than the maximum
weights indicated may result in instability causing possible
injury.
4. If leaving the display in a straight upright position, it is
recommended that a bolt (not provided) be placed through
the head assembly (see Figure 9) to lock the display into the
upright position.
Cable Management
1. Signal cables can be run down the front flap of the center
post and out the front ofthe post atany of the openings.
(See Figure 10)
WARNING: CART CAN TIP OVER RESULTING IN RISK
OF INJURY. Do not allow children under 16 to move cart.
Only adults should move this cart. Move cart slowly. Apply
moving force on narrow dimension. Never apply force at top -
always push near middle. Push, don’t pull.
2. The display power cord can be run through the top and
down through the post to exit out the back. (See Figure 10)
3. Any accessory power cords can be run through the front
and down through the post to exit out the back. (See
Figure 10)
4. Install the snap-on covers to any opening that is not being
used. (See Figure 10)
5. To remove the snap-on covers, grip the sides of the cover
in the middle and pull off. They can also be removed by
inserting a flat-blade screwdriver into the bottom slot and
rotating the screwdriver.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
MFC, PFC Series
2. Pull back on flag on upper mounting hole and press pin
down into "Open" position. (See Figure 13)
WARNING: EACH DISPLAY MAY WEIGH IN EXCESS OF
40 LBS! Always use two people and proper lifting techniques
when installing or positioning display on stand.
Do NOT push
cart near top
3. Carefully lift display from cart.
4. Lift up on pin and place flag back against faceplate to return
it to "Closed" position. (See Figure 13)
Push cart near
middle
Remove bolt
or padlock
1
2
if used
Pin in
"Closed"
position -
move to
"Open"
position to
remove
display
Figure 11
1. Always place cart on level surface.
2. Always lock the wheels when the cart is not moving.
3. Check and tighten the hex nuts on the casters occasionally.
(See Figure 12) These should be checked especially after
use on uneven ground.
4
Pin in
"Open"
position -
move to
"Closed"
position
after display
is removed.
x 4
Figure 13
Figure 12
Removing Display from Cart
1. Remove bolt or padlock from faceplate (if used).
(See Figure 13)
NOTE: The pin may have been used as a more permanent
locking device. If so, remove nut and pin and move
from the lower holes to the upper holes.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
MFC, PFC Series
Installation Instructions
USA/International
Europe
A
P
F
A
P
F
8401 Eagle Creek Parkway, Savage, MN 55378
800.582.6480 / 952.894.6280
877.894.6918 / 952.894.6918
Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
+31 (0)40 2668620
+31 (0)40 2668615
Asia Pacific
A
Room 30I, Block D, Lily YinDu International Building
LuoGang, BuJi Town, Shenzhen, CHINA. Post Code: 518112
8809-000038 Rev.B
¤2007 Chief Manufacturing
06/07
P
F
+86-755-8996 9226 ; 8996 9236 ; 8996 9220
+86-755-8996 9217
Download from Www.Somanuals.com. All Manuals Search And Download.
|