I N S T A L L A T I O N I N S T R U C T I O N S
Instrucciones de instalación
Installationsanleitung
Istruzioni di installazione
Installatie-instructies
Instruções de Instalação
Instructions d´installation
Direct Attach Ceiling Mount
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
JHS SERIES
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
JHS SERIES
LEGEND
Tighten Fastener
Phillips Screwdriver
Destornillador Phillips
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Ɉɬɜɟɪɬɤɚ
ɋɨɠɦɢɬɟꢀɁɚɫɬɟɠɤɭ
Loosen Fastener
Hex-Head Wrench
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
ɈɫɥɚɛɶɬɟꢀɁɚɫɬɟɠɤɭ
Zeskantsleutel
Clé à tête hexagonale
Ʉɥɸɱꢀɫꢀɲɟɫɬɢɝɪɚɧɧɨɣꢀɝɨɥɨɜɤɨɣ
TOOLS REQUIRED FOR INSTALLATION AND PARTS
5/32" (provided)
3/16" (provided)
A (1)
I/M
B (2)
5/16-18 x 3/8"
x 1
Interface Bracket
Kit
(including hardware)
x 1
3
Download from Www.Somanuals.com. All Manuals Search And Download.
JHS SERIES
Installation Instructions
Display Installation
INSTALLATION
Mount Installation
1. Determine mounting pattern on display.
IMPORTANT ! : The following installation instructions
assume that a 1-1/2" NPT pipe has been properly
installed and is in place.
WARNING: IMPROPER INSTALLATION CAN LEAD TO
EQUIPMENT FALLING CAUSING SERIOUS PERSONAL
INJURY AND DAMAGE TO EQUIPMENT! DO NOT
substitute hardware. Use only hardware supplied by
manufacturer!
1. Thread mount (A) onto 1-1/2" NPT pipe until hand tight.
2. Adjust mount (A) position until Centris cup is facing the
desired position of the display. (See Figure 1)
WARNING: IMPROPER INSTALLATION CAN LEAD TO
ELECTRIC SHOCK OR DAMAGE TO EQUIPMENT! Screw
length must not exceed the depth of threaded mounting insert
in display.
1-1/2" NPT Pipe
1
WARNING: OVERTIGHTENING OF SCREWS CAN
DAMAGE PARTS AND LEAD TO SERIOUS PERSONAL
INJURY AND DAMAGE TO EQUIPMENT! DO NOT over
tighten screws when installing interface bracket.
Centris Cup
NOTE: If the display being installed has a 100x100 VESA
mounting pattern, no interface bracket is required and
the display can be mounted directly to the Centris cup
as outlined below.
(A)
NOTE: If the display being installed requires an interface
bracket, refer to the interface bracket installation
instructions.
WARNING: IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Using screws of
improper size may damage your display! Proper screws will
easily and completely thread into display mounting holes.
Ensure that screws are not too long.
Figure 1
3. Whenmount(A)isproperlypositionedsecuremount(A)to
1-1/2" NPT pipe by installing and tightening 5/16-18 x 3/8"
set screw (B) using 3/16" hex wrench. (See Figure 2)
NOTE: If mount is being used to couple two pipes, use both set
screws when securing mount (A) to pipes.
WARNING: IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Inadequate thread
engagement in display may cause display to fall! Back out
screws ONLY as necessary to allow installation of Centris
cup!
(B) x 1
(A)
1. Start two M4 x 8mm Phillips pan head screws (included in
hardware kit) into upper mounting holes in display back.
(See Figure 3)
(B) x 1
NOTE: Leave at least 1/8" of each screw protruding out back
2
of display.
2
(A)
Figure 2
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
JHS SERIES
Adjustments
To adjust display Roll, Pitch, and YAW tension:
1. Disconnect all wires and cable from the display.
2. Remove two Lower screws securing display to Centris cup.
3. Loosen two Upper screws securing display.
4. Lift display upward and away from mount.
5. Using a hex head wrench turn the tension adjustment screw
clockwise to increase tension, or counter-clockwise to
decrease tension. (See Figure 5)
6. Re-install display.
1
x2
Figure 3
2. Align two screws in display back with upper mounting holes
in Centris cup and lower display until screws are seated in
lower area of teardrop mounting holes. (See Figure 4)
3. Install two more of the same screws through lower mounting
holes in Centris cup and into display back. (See Figure 4)
4. Tighten all hardware.
5. Route cables and wires to display.
2
Figure 5
3
4
x 2
Figure 4
5
Download from Www.Somanuals.com. All Manuals Search And Download.
JHS SERIES
Installation Instructions
USA/International
Europe
A
P
F
A
P
F
8401 Eagle Creek Parkway, Savage, MN 55378
800.582.6480 / 952.894.6280
877.894.6918 / 952.894.6918
Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
+31 (0)40 2668620
Chief Manufacturing, a division of
Milestone AV Technologies
+31 (0)40 2668615
Asia Pacific
A
Room 24F, Block D, Lily YinDu International Building
LuoGang, BuJi Town, Shenzhen, CHINA.
8805-000220 Rev A
¤2008 Milestone AV Technologies
06/08
P
F
+86-755-8996 9226
+86-755-8996 9217
Download from Www.Somanuals.com. All Manuals Search And Download.
|