User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Table of Contents
Additional Features....................................................................................................................................3
DMX Channel Summary.................................................................................................................4
Product Overview...........................................................................................................................5
3. Setup................................................................................................................................6
AC Power.......................................................................................................................................6
AC Plug..................................................................................................................................................... 6
Power Linking............................................................................................................................................6
Fuse Replacement.....................................................................................................................................6
DMX Modes...............................................................................................................................................7
Master/Slave Connectivity.......................................................................................................................... 7
Orientation.................................................................................................................................................8
Rigging...................................................................................................................................................... 8
Control Panel Description...............................................................................................................9
DMX Personality ........................................................................................................................................9
DMX Control Without ID Addressing...........................................................................................................9
Static Color.............................................................................................................................................. 10
Edit Customs........................................................................................................................................... 10
TOUR Notes.................................................................................................................................13
Menu Map....................................................................................................................................14
DMX Values .................................................................................................................................15
ARC1 + D................................................................................................................................................ 16
COLORado™ 1-Tri IP User Manual Rev. 01c
-a-
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
5. Technical Information...................................................................................................18
Claims..........................................................................................................................................22
-b-
COLORado™ 1-Tri IP User Manual Rev. 01c
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Begin
1. Before You Begin
·
·
·
·
·
·
·
·
·
·
One COLORado™ 1-Tri IP
What is
Included
One proprietary IP66 to Edison power input cable (US market)
One proprietary IP66 power extension cable
One proprietary IP66 signal extension cable
One DMX input cable (proprietary IP66 to 3-pin XLR male)
One DMX output cable (proprietary IP66 to 3-pin XLR female)
One gel frame holder
One safety cable
Warranty Card
Quick Reference Guide
Immediately upon receiving this product, carefully unpack it and check the container in
which you received it. Make sure that you have received all the parts indicated above
and that they are all in good condition. If the material inside the container (this product
and any other accessory included with it) appears damaged from shipping, or if the
container shows signs of mishandling, notify the shipper immediately. In addition, retain
the container and all the packing material for inspection.
Unpacking
Instructions
See the Claims section in the Technical Information chapter.
Convention
Meaning
Typographic
Conventions
1~512
50/60
[10]
A range of values in the text
A set of mutually exclusive values in the text
A DIP switch to be configured
Claims
A new term, or a section or chapter in this document
“COLORado™ UM” The name of another publication or manual
<SET>
Settings
MENU > Settings
1~10
A button on the fixture’s control panel
A fixture function or a menu option
A sequence of menu options
A range of menu values from which to choose in a menu
A set of two mutually exclusive menu options in a menu
A unique value to entered or select in a menu
Yes/No
ON
Icon
Meaning
Icon Meaning
This icon indicates critical installation, configuration, or operation
information. Failure to comply with this information may render
the fixture partially or completely inoperative, damage third-party
equipment, or cause harm to the user.
This icon indicates important installation or configuration
information. Failure to comply with this information may prevent
the fixture from functioning correctly.
This icon indicates useful, although non-critical information.
The term “DMX” used throughout this document refers to the USITT DMX512-A
transmission protocol.
COLORado™ 1-Tri IP User Manual Rev. 01c
-1-
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Begin
Please read the following notes carefully because they include important safety
information about the installation, usage, and maintenance of this product.
Safety Notes
It is important to read all these notes before starting to work with this product.
There are no user serviceable parts inside this product. Any reference to
servicing it you may find from now on in this User Manual will only apply to
properly CHAUVET® certified technicians. Do not open the housing or attempt
any repairs unless you are one of them.
Please refer to all applicable local codes and regulations for the proper
installation of this product.
Keep this manual for future consultation. If you sell this product to another user,
make sure that they also receive this manual.
·
·
·
·
Avoid direct eye exposure to the light source while the fixture is on.
Personal Safety
Always disconnect this product from its power source before servicing.
Always connect this product to a grounded circuit to avoid the risk of electrocution.
Do not touch this product’s housing when operating because it may be very hot.
·
·
·
This product is for indoor and outdoor use (IP66). Do not submerge it.
Mounting and Rigging
Power and Wiring
Make sure there are no flammable materials close to this product while operating.
When hanging this product, always secure it to a fastening device using a safety
cable (included).
·
Always make sure that you are connecting this product to the proper voltage, as
per the specifications in this manual or on the product’s sticker.
·
·
Never connect this product to a dimmer pack or rheostat.
Make sure the product’s housing or power cable are not cracked, crimped, or
damaged.
·
·
Never disconnect this product by pulling or tugging on the power cable.
Do not operate this fixture if you see damage on the housing, lenses or cables;
have the damaged parts replaced by an authorized technician at once.
Operation
·
·
The maximum ambient temperature (Ta) is 104° F (40° C). Do not operate this
product at a higher temperature.
In case of a serious operating problem, stop using this product immediately!
In the unlikely event that your CHAUVET® product may require service, please
contact CHAUVET® Technical Support.
LEDs gradually decline in brightness over time, mostly because of heat. Packaged in
clusters, LEDs exhibit higher operating temperatures than in ideal, single LED
conditions. For this reason, using clustered LEDs at their fullest intensity significantly
reduces the LEDs’ lifespan. Under normal conditions, this lifespan can be of 40,000 to
50,000 hours. If extending this lifespan is vital, lower the operational temperature by
improving the fixture’s ventilation and reducing the external temperature. In addition,
limiting the overall projection intensity may also help to extend the LEDs’ lifespan.
Expected LED
Lifespan
-2-
COLORado™ 1-Tri IP User Manual Rev. 01c
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
2. Introduction
The COLORado™ 1-Tri IP is an RGB wash light based on 14 tri-color LEDs. It consists
of a single pod with a double bracket mounting yoke. The AC power comes directly into
the fixture’s housing through a proprietary IP66 rated power input cord. The power
linking uses a proprietary IP66 rated power link cord. The DMX input and output signals
use proprietary IP66 DMX in and DMX out cords. The fixture comes with all the
necessary adapters to connect to the proprietary IP66 cords as well a power and signal
link cables. The COLORado™ 1-Tri IP uses a display-based control panel for
programming functions.
Product
Description
·
·
3, 4, 5, or 10-channel RGB LED wash light (with ID addressing)
Operating modes:
Features
3-channel:
3-channel:
4-channel:
5-channel:
RGB control
HSV (hue, saturation, and value) control
RGB, dimmer
RGB, dimmer, strobe
10-channel: RGB, ID, dimmer, strobe, macro, auto/custom, dimmer speed,
auto speed
·
·
·
·
·
·
High power (3W) tri-color (RGB) LEDs
RGB color mixing with or without DMX controller
Automatic programs
User configurable custom programs
Recall auto and custom programs via master/slave or DMX
Color temperature presets (3,200~10,000 K)
·
·
·
·
·
·
·
·
·
Five distinct dimming curves
Additional Features
3-pin DMX input and output connectors
Power linking: max 12 units @ 120 V
LED display with password protection
Gel frame holder (4 mm max thickness)
Double-bracket yoke that doubles as floor stand
Color calibration
Durable and weather resistant IP66 rated housing
IP66 power and DMX connectors
·
·
16.4 ft (5 m) power extension cable (IP5POWER)
16.4 ft (5 m) signal extension cable (IP5SIG)
Options
COLORado™ 1-Tri IP User Manual Rev. 01c
-3-
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
DMX Channel Summary
DMX Channel
Function
Master Dimmer
Red
TOUR
1
2
3
Green
4
Blue
5
6
Color Macro
Strobe
7
8
9
10
Auto Programs
Auto Speed Adjust
Dimmer Speed
ID Address
DMX Channel
Function
Red
Green
Blue
ARC1
1
2
3
DMX Channel
Function
Master Dimmer
Red
Green
Blue
AR1 + D
1
2
3
4
DMX Channel
Function
Master Dimmer
Red
Green
Blue
AR1 + S
HSV
1
2
3
4
5
Strobe
DMX Channel
Function
Hue
Saturation
Value
1
2
3
-4-
COLORado™ 1-Tri IP User Manual Rev. 01c
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
3. Setup
The COLORado™ 1-Tri IP has an auto-ranging power supply that can work with an
input voltage range of 100~240 VAC, 50/60 Hz.
AC Power
Make sure that you are connecting this product to the proper voltage, as per the
specifications in this guide, the product’s user manual, or on the product’s sticker.
Always connect the COLORado™ 1-Tri IP to
a
protected circuit with an
appropriate electrical ground to avoid the risk of electrocution or fire.
To determine the power requirements for the COLORado™ 1-Tri IP see the label affixed
to the side of the fixture. Alternatively, you may refer to the corresponding specifications
chart in the Technical Information chapter of this manual.
The listed current rating indicates the maximum current draw during normal operation.
For more information, you may download the “Sizing the Circuit Breakers” document
from the CHAUVET® Web site.
Never connect the COLORado™ 1-Tri IP to a rheostat (variable resistor) or dimmer
circuit, even if the rheostat or dimmer channel serves only as a 0 to 100% switch.
Each COLORado™ 1-Tri IP has IP66 rated cords for Power In and Power Out with
proprietary IP66 connectors. These power cords access the sealed body of the fixture
through IP66 cable glands. To allow connection to power outlets, the fixture comes with
a power input cord with a proprietary IP66 connector on one end and an Edison plug on
the other end (US market). In case you need to replace the Edison plug on the power
input cord, follow the table below.
AC Plug
Connection
AC Live
Wire (US)
Black
Wire (Europe)
Brown
IP66 Pin
Screw Color
Yellow or Brass
Silver
1
2
3
AC Neutral
AC Ground
White
Blue
Green/Yellow
Green/Yellow
Green
The COLORado™ 1-Tri IP supports power linking for up to 12 other COLORado™ 1-Tri
IP fixtures at 120 VAC. The fixture also comes with an IP66 power linking cord to allow
direct connection between fixtures.
Power Linking
The COLORado™ 1-Tri IP fixture has no external fuse that the user can change.
However, it does have an internal fuse that only an authorized CHAUVET® technician
should change.
Fuse Replacement
-6-
COLORado™ 1-Tri IP User Manual Rev. 01c
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
You may link any COLORado™ 1-Tri IP fixture to a DMX controller using a standard
DMX serial connection. If using other DMX compatible fixtures with a COLORado™ 1-
Tri IP fixture, it is possible to control them individually with a single DMX controller.
DMX Linking
If you are not familiar with the DMX standard, or if you need information about the DMX
cables needed to link the COLORado™ 1-Tri IP fixture to a DMX controller, you may
download the “DMX Primer” document from the CHAUVET® Web site.
The COLORado™ 1-Tri IP comes with two adapter cables, one from proprietary
IP66 to 3-pin DMX In and the other from proprietary IP66 to 3-pin DMX Out. In
addition, it comes with a signal linking cable with proprietary IP66 connectors on
both ends.
The COLORado™ 1-Tri IP uses the standard DMX data connection for its DMX modes,
TOUR, ARC1, AR1+D, AR1+S, and HSV.
DMX Modes
You will find information about these DMX modes in the Introduction chapter (brief
description), the Operation Instructions chapter (configuration details), and the DMX
Values section (individual channel values).
The Master/Slave mode allows a COLORado™ 1-Tri IP fixture to control one or more
COLORado™ 1-Tri IP fixtures without a DMX controller. The controlling fixture becomes
the “master” when running an auto or custom program as well as when in STATIC
mode. The controlled fixtures are the “slaves” and you must set them to “SLAVE” mode
from their respective control panels. During the Master/Slave operation, the slave
fixtures will operate in unison with the master fixture.
Master/Slave
Connectivity
The master and slave fixtures link to each other using the standard DMX serial
connection. If you are not familiar with the Master/Slave connectivity, you may download
the “DMX Primer” document from the CHAUVET® Web site.
DO NOT connect a DMX controller to the fixtures operating in Master/Slave mode.
Otherwise, the signals from the DMX controller may interfere with the signals from
the master unit.
The Operation chapter of this manual provides detailed instructions on how to
configure the Master and Slave units.
The COLORado™ 1-Tri IP uses the ID Addressing feature to increase the number of
addressable fixtures in the same DMX universe when in the TOUR personality. Refer to
the Operation chapter in this manual to learn in detail how to configure the
COLORado™ 1-Tri IP fixtures when using ID Addressing. If you are not familiar with the
various connection methods when using ID Addressing, you may download the “DMX
Primer” document from the CHAUVET® Web site.
ID Addressing
COLORado™ 1-Tri IP User Manual Rev. 01c
-7-
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
Before mounting this fixture, read and follow the safety recommendations indicated in
the Safety Notes section (page 2 of this manual).
Mounting
Always mount this fixture in any safe position while making sure that there is adequate
room around it for ventilation, configuration, and maintenance.
Orientation
Make sure to mount this fixture away from any flammable material as indicated in the
Safety Notes section.
The COLORado™ 1-Tri IP consists of a sealed (IP66) housing with a double bracket
mounting yoke. It has two DMX signal cables (DMX In/DMX Out), and two power cables
(Power In/Power Out), all of them fitted with proprietary IP66 connectors.
Rigging
CHAUVET® recommends following the general guidelines below when mounting the
COLORado™ 1-Tri IP.
·
·
When selecting an installation location, consider ease of access to the fixture for
operation, programming adjustments, and routine maintenance.
If hanging this fixture, make sure that the location where you are mounting the
fixture can support its weight. Please see the Technical Specifications section of this
manual for the weight requirement of this fixture.
The COLORado™ 1-Tri IP includes a safety cable and a mounting yoke to which you
can attach one or two rigging clamps. You must supply your own “C” or “O” clamps and
make sure that they are capable of supporting the weight of this fixture. Although it is
possible to use a single clamp per fixture, CHAUVET® recommends using two clamps
per fixture. Secure the fixture with the safety cable after mounting it to the truss.
Procedure
C clamp
(not included).
Product Mounting
Diagram
Floor Mounting
Secure the safety cable using
the passageway on the back
of the fixture.
Overhead Mounting
-8-
COLORado™ 1-Tri IP User Manual Rev. 01c
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
4. Operation
Button
Function
Control Panel
Description
Exits from the current menu or
function
Enables the currently displayed
menu or sets the currently
selected value in to the current
function
<MENU>
<ENTER>
Navigates upwards through the
menu list and increases the
numeric value when in a function
Navigates downwards through
the menu list and decreases the
numeric value when in a function
<UP>
<DOWN>
You can set the COLORado™ 1-Tri IP start address in the 001~512 DMX range. This
allows for the control of up to 51 fixtures in the 10-channel TOUR personality. In
addition, the ID address system allows you to assign up to 66 fixtures within the same
DMX address, thus multiplying the number of fixtures you can control within a single
universe. You can access the fixture’s ID address system from channel 10 when in the
TOUR personality.
Control Options
When programming live performances as well as cues that need to trigger on
demand or on a time line, program no more than 10 fixtures on ID addressing per
DMX channel. This is to remain within a one-second execution time.
Carry out all the programming procedures indicated below from the control panel. Refer
to the Menu Map on page 14 to learn how the menu options relate to each other.
Programming
To go to an option, press <MENU> repeatedly until the option shows on the display.
To select an option value, press <UP> or <DOWN> until you see the desired value and
press <ENTER> to accept it.
To exit to the previous menu level, press <MENU>.
This setting allows the user to choose a particular DMX personality.
1) Go to PERS.
DMX Personality
2) Select the desired personality (TOUR, ARC1, AR1 + D, AR1 + S, or HSV).
3) Make sure that the starting addresses on the various fixtures do not overlap due to
the new personality setting. See the DMX Values section.
In this mode, each unit will respond to a unique starting address from the DMX
controller. All units with the same starting address will respond in unison.
DMX Control
Without ID
Addressing
1) Select the TOUR personality as shown in DMX Personality.
2) Set the running mode:
a) Go to RUN.
b) Select DMX.
3) Set the starting address:
a) Go to DMX.
b) Select the starting address (001~512).
4) Deactivate ID Addressing on each fixture:
a) Go to SET > ID.
b) Select OFF.
Make sure to deactivate ID Addressing in each fixture when using the TOUR
personality. Otherwise, unintended results may occur if channel 10 is not set to
“0”.
Continues on the next page
COLORado™ 1-Tri IP User Manual Rev. 01c
-9-
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Continued from previous page
In this mode, the fixtures with the same DMX starting address will respond to the DMX
controller based on the fixture’s individual ID address setting. If the user selects ID
address “0”, all the fixtures with the same DMX address will respond in unison.
Otherwise, each fixture will follow the control for its particular ID address.
DMX Control With ID
Addressing
1) Repeat steps 1, 2, and 3 from DMX Control Without ID Addressing.
2) Activate ID Addressing in each fixture:
a) Go to SET > ID.
b) Select ON.
3) Select an ID address for each fixture:
a) Go to ID.
b) Select an ID (01~66)
The Static Color mode allows for permanent RGB color mixing without a DMX controller.
1) Go to STAT.
Static Color
2) Select the desired color (Red, Green, or Blue).
3) Select the desired color value (0~255).
4) Repeat for the other colors.
5) Select Strob.
6) Select the desired frequency (0~20).
Auto programs allow for dynamic RGB color mixing without a DMX controller.
1) Go to AUTO.
Auto Programs
Edit Customs
2) Select the desired auto program (AT. 01~10 or PR. 01~10).
You cannot edit auto programs AT. 01~10. However you can edit PR. 01~10 (see
Edit Customs).
This setting allows for the programming of up to 30 scenes for each of the 10
customizable programs, including colors and effects.
1) Go to EDIT.
2) Select the desired auto program (PR. 01~10).
3) Select the desired scene (SC. 01~30).
4) Select the desired color or effect (Red, Green, Blue, Strobe, Time, or Fade).
5) Select the desired value for the color or effect (000~255 for colors and timers, or
00~20 for Strobe).
6) Repeat for the other colors or effects.
7) Repeat for the other scenes.
The Master/Slave mode allows a group of COLORado™ 1-Tri IP fixtures (the slaves) to
execute simultaneously the same program, whether auto or custom, that another
COLORado™ 1-Tri IP fixture (the master) is executing, without a DMX controller.
Master/Slave
1) Set the Master Unit:
a) Set the running mode to DMX as explained in “DMX Control Without ID
Addressing”.
b) Select an auto program as explained in “Auto Programs”.
2) Set the slave units:
a) Go to RUN.
b) Select SLAV.
·
·
The fixture that runs an auto program automatically becomes the Master.
Do not connect a DMX controller to the master or slave fixtures.
Continues on the next page
-10-
COLORado™ 1-Tri IP User Manual Rev. 01c
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Continued from previous page
The COLOR setting determines how the COLORado™ 1-Tri IP displays the white color
when the Red, Green, and Blue faders are all at the “255” value.
Color Adjustment
1) Go to SET > Color.
2) Select OFF, RGBW, or UC.
Setting
Description
OFF
When R, G, and B are “255,” the output will be at its maximum.
RGBW
When R, G, and B are “255,” CAL2 will determine the output.
When R, G, and B are “255,” the output will match that of fixtures from
previous generations.
UC
This setting determines how the output of the COLORado™ 1-Tri IP follows the position
of the Dimmer fader, as well as the Red, Green, and Blue faders.
Dimmer Curves
1) Go to SET > Dim.
2) Select a dimmer curve (Off, Dim1, Dim2, Dim3, or Dim4).
Setting
Description
OFF
Dim1
Dim2
Dim3
Dim4
The output is proportional to the faders’ position (linear)
The output is not proportional (fastest)
The output is not proportional (fast)
The output is not proportional (slow)
The output is not proportional (slowest)
This setting allows the user to activate or disable the control panel lock, which keeps
non-authorized personnel from changing the fixture’s settings.
Control Panel Lock
1) Go to KEY.
2) Select On/ Off.
When the control panel lock is active, the fixture will prompt the user to enter the
password after 30 seconds of control panel inactivity or after turning on the
fixture.
After being prompted to enter the password:
1) Press <UP>, <DOWN>, <UP>, <DOWN>, and <ENTER>.
This option allows the user to copy the custom programs of one COLORado™ 1-Tri IP
fixture onto other COLORado™ 1-Tri IP fixtures by using the Master/Slave method.
Program Upload
1) Configure and connect the fixtures in a Master/Slave arrangement, where the
master unit has the custom programs you want to transfer onto the slave units.
2) At the master unit, go to SET > UPLD.
3) When prompted, enter the master access password as shown in Control Panel
Lock.
4) Wait for the upload process to finish before disconnecting the fixtures.
During and after the upload, the master and slave units will visually indicate the status of
the process, as follows:
Color
Yellow
Red
Meaning
The upload process is running
The upload failed due to an error
The upload finished successfully
Green
Continues on the next page
COLORado™ 1-Tri IP User Manual Rev. 01c
-11-
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Continued from previous page
This setting allows the user to reset the COLORado™ 1-Tri IP fixture to its default
values, including the custom programs.
Reset
1) Go to SET> REST.
2) When prompted, enter the master access password as shown in Control Panel
Lock.
3) Wait for the reset process to finish.
This setting allows the user to edit the temperature of the 11 white colors used in the
Macros channel. The 11 pre-set whites are configurable.
Whites Setting
1) Go to CAL1.
2) Select a white color (WT. 1~11).
3) Select a color (Red, Green, or Blue).
4) Select a color value (0~255).
5) Repeat for the other colors (Red, Green, or Blue).
6) Repeat for the other white colors (WT. 1~11).
This setting allows the user to select the white color shown by the COLORado™ 1-Tri IP
when the color setting is RGBW and the DMX controller’s Red, Green, and Blue faders
are set to “255”.
White Calibration
1) Go to CAL2 > RGBW.
2) Select a color (Red, Green, or Blue).
3) Select a color value (0~255).
4) Repeat for the other colors (Red, Green, or Blue).
-12-
COLORado™ 1-Tri IP User Manual Rev. 01c
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
These notes intent to clarify the way the TOUR DMX personality works.
TOUR Notes
·
·
Channel 1 controls the intensity of the currently projected color.
When the slider is at the highest position (255) the intensity of the output is at its
maximum.
Master Dimmer
·
·
·
Channels 2, 3, and 4 control the intensity ratio of each of the Red, Green, and Blue
LEDs.
When the slider is at the highest position (255), the intensity of each color is at its
Red, Green, & Blue
Color Selection
maximum.
You can combine channels 2, 3, and 4 to create over 16 million colors.
·
·
·
Channel 5 selects the required Color Macro.
Channel 5 has priority over channels 2, 3, and 4.
Channel 1 controls the intensity of the Color Macro.
Color Macros
Strobe
·
·
Channel 6 controls the strobe frequency (not the intensity) of channels 2~5.
Channel 6 strobes channels 2, 3, and 4 when not running macros, allowing the
individual faders (R, G, and B) as well as channel 1 (D) to control the output
intensity.
·
Channel strobes channel 6 when running macros, allowing channel 6 to select the
macro and channel 1 to control the output intensity.
·
·
Channel 7 selects the preset auto programs AT. 01~10 or the custom programs
CUS. 01~10.
When activating the custom programs CUS. 01~10, it is possible to control the Step
Auto
Time and Fade Time using channels 2 and 3 respectively.
·
·
Channel 7 has priority over channels 2, 3, 4, 5, and 6.
Channel 9 is for selecting the dimmer mode and speed. When Dimmer is set to Off,
the Red, Green, Blue, and Dimmer outputs are linear with the faders. Otherwise,
Dim1 is the fastest dimmer curve, while Dim4 is the slowest.
Dimmer Speed
·
·
·
Channel 10 selects the target ID address.
Each independent DMX address may have up to 66 independent ID addresses.
An ID address of 0 will activate all ID address locations.
ID Address
Selection
COLORado™ 1-Tri IP User Manual Rev. 01c
-13-
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
DMX Values
Channel Function
Value
Percent/Setting
TOUR
1
2
Master Dimmer 000 ó 255 0~100%
Red
0~100% (or)
000 ó 255
000 ó 255
Step Time
Green
When playing a custom program
0~100% (or)
3
4
Fade Time
Blue
When playing a custom program
000 ó 255 0~100%
000 ó 010 No function
011 ó 030 R: 100% G: Up
B: 0%
031 ó 050 R: Down G: 100% B: 0%
051 ó 070 R: 0%
071 ó 090 R: 0%
091 ó 110 R: Up
111 ó 130 R: 100% G: 0%
131 ó 150 R: 100% G: Up
G: 100% B: Up
G: Down B: 100%
G: 0%
B: 100%
B: Down
B: Up
151 ó 170 R: Down G: Down B: 100%
171 ó 200 R: 100% G: 100% B: 100% W: 100%
201 ó 205 White 1: 3,200 K
206 ó 210 White 2: 3,400 K
211 ó 215 White 3: 4,200 K
216 ó 220 White 4: 4,900 K
221 ó 225 White 5: 5,600 K
226 ó 230 White 6: 5,900 K
231 ó 235 White 7: 6,500 K
236 ó 240 White 8: 7,200 K
241 ó 245 White 9: 8,000 K
246 ó 250 White 10: 8,500 K
251 ó 255 White 11: 10,000 K
5
Color Macro
000 ó 010 No function
011 ó 255 0~20 Hz
6
Strobe
000 ó 020 No function
021 ó 030 Auto 1
031 ó 040 Auto 2
041 ó 050 Auto 3
051 ó 060 Auto 4
061 ó 070 Auto 5
071 ó 080 Auto 6
081 ó 090 Auto 7
091 ó 100 Auto 8
101 ó 110 Auto 9
111 ó 120 Auto 10
121 ó 130 Custom 1
131 ó 140 Custom 2
141 ó 150 Custom 3
151 ó 160 Custom 4
161 ó 170 Custom 5
171 ó 180 Custom 6
181 ó 190 Custom 7
191 ó 200 Custom 8
201 ó 210 Custom 9
211 ó 220 Custom 10
221 ó 255 No function
7
Auto
8
9
Auto Speed
000 ó 255 0~100% (Only when playing an automatic program)
000 ó 009 Use dimmer speed from control panel
010 ó 029 Linear dimmer
030 ó 069 Non-linear dimmer 1 (fastest)
070 ó 129 Non-linear dimmer 2
Dimmer Speed
130 ó 189 Non-linear dimmer 3
190 ó 255 Non-linear dimmer 4 (slowest)
Continues on the next page
COLORado™ 1-Tri IP User Manual Rev. 01c
-15-
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Continued from previous page
Channel
Function
Value
Setting
Value Setting
Value
Setting
ID 46
TOUR (Cont.)
000 ó 009 All IDs
010 ó 019 ID 1
020 ó 029 ID 2
030 ó 039 ID 3
040 ó 049 ID 4
050 ó 059 ID 5
060 ó 069 ID 6
070 ó 079 ID 7
080 ó 089 ID 8
090 ó 099 ID 9
100 ó 109 ID 10
110 ó 119 ID 11
120 ó 129 ID 12
130 ó 139 ID 13
140 ó 149 ID 14
150 ó 159 ID 15
160 ó 169 ID 16
170 ó 179 ID 17
180 ó 189 ID 18
190 ó 199 ID 19
200 ó 209 ID 20
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
ID 23
ID 24
ID 25
ID 26
ID 27
ID 28
ID 29
ID 30
ID 31
ID 32
ID 33
ID 34
ID 35
ID 36
ID 37
ID 38
ID 39
ID 40
ID 41
ID 42
ID 43
ID 44
ID 45
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
ID 47
ID 48
ID 49
ID 50
ID 51
ID 52
ID 53
ID 54
ID 55
ID 56
ID 57
ID 58
ID 59
ID 60
ID 61
ID 62
ID 63
ID 64
ID 65
ID 66
10
ID Address
210
211
ID 21
ID 22
Channel Function
Value
Percent/Setting
ARC1
1
2
3
Red
000 ó 255 0~100%
000 ó 255 0~100%
000 ó 255 0~100%
Green
Blue
Channel Function
Value
Percent/Setting
ARC1 + D
1
2
3
4
Master Dimmer 000 ó 255 0~100%
Red
000 ó 255 0~100%
000 ó 255 0~100%
000 ó 255 0~100%
Green
Blue
Channel Function
Value
Percent/Setting
AR1 + S
1
2
3
4
Master Dimmer 000 ó 255 0~100%
Red
000 ó 255 0~100%
000 ó 255 0~100%
000 ó 255 0~100%
Green
Blue
000 ó 010 No function
011 ó 255 0~20 Hz
5
Strobe
Continues on the next page
-16-
COLORado™ 1-Tri IP User Manual Rev. 01c
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Continued from previous page
Channel Function
Value
Percent/Setting
HSV
1
2
3
Hue
000 ó 255 0~100%
000 ó 255 0~100%
000 ó 255 0~100%
Saturation
Value
·
·
“Hue” refers to the visible light, such as red, yellow, and cyan, etc.
“Saturation” indicates the dominance of hue in the color; when saturation is at 100%,
the color is at its purest.
·
“Value” is the color’s brightness; when value is at 100%, the color is at its brightest.
COLORado™ 1-Tri IP User Manual Rev. 01c
-17-
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Information
5. Technical Information
To maintain optimum performance and minimize wear, the user should clean the light
General
Maintenance
fixtures frequently. Usage and environment are contributing factors in determining the
cleaning frequency. As a rule, the user should clean the fixtures at least twice a month.
Dust build up reduces light output performance and can cause overheating. This can
lead to reduced light source life and increased mechanical wear.
CHAUVET® recommends cleaning the fixture’s external optics with a soft cloth using
normal glass cleaning fluid.
To clean a fixture, follow the recommendations below:
·
·
·
Unplug the fixture from power.
Wait until the fixture is cold.
Use a vacuum (or dry compressed air) and a soft brush to remove dust collected
on the external vents and reachable internal components.
·
·
Clean all external optics and glass surfaces with a mild solution of glass cleaner or
isopropyl alcohol, and a soft, lint free cotton cloth or a lens cleaning tissue.
Apply the solution directly to the cloth or tissue and drag any dirt and grime to the
outside of the lens.
·
·
Gently polish the external glass surfaces until they are free of haze and lint.
When cleaning units with a movable mirror, you should keep the contact with the
mirror surface to a minimum to avoid scratching or damaging it.
Always dry the external optics and glass surfaces carefully after cleaning them.
If the fixture has one or more cooling fans, refrain from spinning them using
compressed air.
-18-
COLORado™ 1-Tri IP User Manual Rev. 01c
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Information
Troubleshooting Guide
Symptom
Cause(s)
Dirty lens assembly
Action(s)
Clean the fixture regularly
Install lens assembly properly
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
General low light intensity
Misaligned lens assembly
Faulty LED
Replace the LED board
A single tri color LED
does not illuminate
Faulty LED board
Replace the LED board
Faulty LED
Replace the LED board
A group of tri-color LEDs
does not illuminate
Faulty LED board
Replace the LED board
Faulty LED driver
Replace the LED driver board
Replace the LED board
Faulty LED PCB
None of the LEDs are
illuminating
Faulty LED Driver PCB
Faulty main PCB
Replace the LED driver board
Replace the Display / Main board
Check total load placed on the electrical circuit
Check for a short in the electrical wiring
Check for power on power outlet
Check power cord
Excessive circuit load
Short circuit along the power wires
No power
Breaker/Fuse keeps
blowing
Loose or damaged power cord
Blown internal fuse
Faulty internal power supply
Wrong DMX addressing
Damaged DMX cables
Wrong polarity on the controller
Loose DMX cables
Faulty DMX interface
Faulty Main PCB
Fixture does not power up
Replace internal fuse
Replace internal power supply
Check Control Panel and unit addressing
Check DMX cables
Check polarity switch settings on the controller
Check cable connections
Fixture does not respond
to DMX
Replace Main PCB
Replace Main PCB
Non DMX cables
Use only DMX compatible cables
Install terminator as suggested
Bouncing signals
Long cable / low level signal
Install an optically coupled DMX splitter right
after fixture with strong signal
DMX signal problems
·
·
Too many fixtures
·
·
Install an optically coupled DMX splitter after
unit #32
Interference from AC wires
Keep DMX cables separated from power cables
or black lights
If you still experience technical problems after trying the above solutions, contact
CHAUVET® Technical Support.
COLORado™ 1-Tri IP User Manual Rev. 01c
-19-
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Information
Exploded View
Item
1
Description
Item
11
12
13
14
15
16
17
18
19
20
Description
Display clear plate
Front cover
Rubber seal (*)
Clear glass
2
Button seal
3
Casing
4
Lens complete set
LED board
Stainless steel knob
Power cord gland
Display protection plate
Display plate seal
DMX cable gland
Main bracket
5
6
Heat sink
7
Power supply
Driver board
8
9
Power connection board
Display board
10
Secondary bracket
The rubber seal can be a separate ring or it may come mounted around the
glass cover
(*):
-20-
COLORado™ 1-Tri IP User Manual Rev. 01c
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Information
The user must send the merchandise prepaid, in the original box, and with its original
packing and accessories. CHAUVET® will not issue call tags.
Returns
Procedure
Call CHAUVET® and request a Return Merchandise Authorization Number (RMA #)
before shipping the fixture. Be prepared to provide the model number, serial number,
and a brief description of the cause for the return.
The user must clearly label the package with a Return Merchandise Authorization
Number (RMA #). CHAUVET® will refuse any product returned without an RMA #.
DO NOT write the RMA # directly on the box. Instead, write it on a properly affixed
label.
Once you receive the RMA #, please include the following information on a piece of
paper inside the box:
·
·
·
·
·
Your name
Your address
Your phone number
The RMA #
A brief description of the problem
Be sure to pack the fixture properly. Any shipping damage resulting from inadequate
packaging will be the customer’s responsibility. As a suggestion, proper UPS packing or
double-boxing is always a safe method to use.
CHAUVET® reserves the right to use its own discretion to repair or replace
returned product(s).
The carrier is responsible for any damage incurred during shipping to this product or any
part that shipped with it. Therefore, if the received merchandise appears to have
damages caused during shipping, the customer must submit the damage report and any
related claims with the carrier, not CHAUVET®. The customer must submit the report
upon reception of the damaged merchandise. Failure to do so in a timely manner may
invalidate the customer’s claim with the carrier.
Claims
For other issues such as missing components or parts, damage not related to shipping,
or concealed damage, the customer must make claims to CHAUVET® within seven (7)
days of receiving the merchandise.
World Headquarters
Contact Us
General Information
CHAUVET®
5200 NW 108th Avenue
Sunrise, FL 33351
Voice: (954) 929-1115
Fax: (954) 929-5560
Toll free: (800) 762-1084
Technical Support
Voice: (954) 929-1115 (Press 4)
Fax: (954) 756-8015
World Wide Web
-22-
COLORado™ 1-Tri IP User Manual Rev. 01c
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Information
Technical Specifications
Length
9.6 in (245 mm)
Width
Height
Weight
Dimensions and Weight
8.0 in (205 mm)
9.6 in (245 mm)
10.6 lbs (4.8 kg)
Note: Dimensions in inches rounded to the nearest decimal digit.
Power Supply Type
Range
Voltage Selection
Power
Switching (internal)
100~240 V, 50/60 Hz
Auto-ranging
Parameter
Consumption
Inrush current
Power Linking
120 V, 60 Hz
88 W (0.7 A)
0.4 A
230 V, 50 Hz
88 W (0.4 A)
0.4 A
12 units
24 units
Power I/O
Connectors
Input
Output
In-line proprietary IP66
Proprietary IP66 to Edison
In-line proprietary IP66
Proprietary IP66
Cord plug (US)
Type
Power
Lifespan
Light Source
Photo Optic
LED
3 W
50,000 hours
Color
Quantity
Current
Tri-color (RGB)
14
1,050 mA per die
Parameter
Illuminance @ 5 m
Beam angle
Standard 16º Optics
306 lx
17º
Field angle
32º
Maximum External Temp.
Cooling System
Thermal
DMX
104° F (40° C)
Convection
I/O Connectors
Connector Type
Channel Range
3-pin XLR (IP66 adapter)
In-line
3, 4, 5, and 10
COLORado™ 1-Tri IP
Power extension cable
Signal extension cable
Ordering
COLORADO1TRIIP
IP5POWER
IP5SIG
COLORado™ 1-Tri IP User Manual Rev. 01c
-23-
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAUVET®
5200 NW 108th Avenue
Sunrise, FL 33351 (USA)
(800) 762-1084 – (954) 929-1115
FAX (954) 929-5560
COLORado™ 1-Tri IP User Manual Rev. 01c
December 2010
Download from Www.Somanuals.com. All Manuals Search And Download.
|