03201560 • 04201113
Smoker, BBQ and Grill
Tools needed for
assembly:
2 Adjustable Wrenches
7/16” Open-End Wrench
Flat Screwdriver
Hammer
CARBON MONOXIDE HAZARD
THIS UNIT IS HEAVY. DO NOT assemble without helper.
Burning charcoal inside can kill
Some parts may contain sharp edges - especially as noted in
manual. Wear protective gloves if necessary.
you. It gives off carbon monoxide,
which has no odor. NEVER burn
Read and follow all safety statements, warning, assembly
instructions and use & care directions before attempting to
assemble and cook.
charcoal inside homes, vehicles
or tents.
42802119 (01-09-04)
Download from Www.Somanuals.com. All Manuals Search And Download.
FIRST, GET A HELPER! This unit is heavy and requires a second person for lifting and moving. NEXT, pick a suitable location to
work. Open the carton and slit the corners so that the carton lays flat. This will give you a protective work surface during assembly.
1
TO BEGIN ASSEMBLY, build two leg assemblies by sliding the long leg sections into the short leg sections.
Short leg section
Long leg section
Attach leg braces to the outside of one leg assembly using #10-24x1¾” screws and #10-24 flange nuts. Make sure slotted
(oval) hole is toward bottom of leg. Do not fully tighten screws until Step 8 is complete.
2
Leg brace
Leg brace
Slotted
hole
Download from Www.Somanuals.com. All Manuals Search And Download.
Lay the leg assembly on its side with legs braces pointing upward. Insert the wood rack hooks into leg holes and swing rack
upward, parallel to leg braces.
3
Wood rack
With the aid of a helper, place leg holes of remaining leg assembly over wood rack hooks and rotate leg assembly until it meets
the leg braces. Make sure both short legs are at one end of the rack and both long legs at the other end. Attach to leg braces
using #10-24x1¾” screws and #10-24 flange nuts. Do not fully tighten screws until Step 8 is complete.
4
Short leg
Long leg
Short leg
Long leg
Download from Www.Somanuals.com. All Manuals Search And Download.
Insert a cotter pin into the hole at one end of the axle and bend the ends of the pin back so that it cannot be removed. Slide a
wheel onto the axle. Slide the axle through the holes at the ends of the short legs. Slide remaining wheel onto axle and secure
with remaining cotter pin.
5
6
Cotter pin
Axle
Cotter pin
NOTE: Smoker chamber door not pictured
for clarity.
Open end up
Stand the leg assembly on end, wheels
down. Stand the smoker chamber on its
solid end, open end up. Place leg assembly
against chamber, aligning holes in legs with
holes in chamber. Attach legs to chamber
using four 1/4-20x2” screws and 1/4-20
flange nuts. Insert screws from outside,
flange nuts inside chamber.
Smoker chamber
FULLY TIGHTEN ALL SCREWS AND
NUTS AT THIS TIME.
Wheels down
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE: Smoker chamber and firebox doors not pictured for clarity.
Diamond FireTM Plate Installation - For models without Diamond FireTM ignitor accessory,
part number 22504850.
For models that feature the Diamond FireTM ignitor accessory, supplemental
instructions are included with ignitor.
7
First, locate the cover plate in the hardware box. At the bottom right end of the
Firebox
firebox there is an opening for the Diamond FireTM ignitor accessory. Install the
cover plate over the opening using two #8-32x1/2” screws and #8-32 lock nuts.
Second, align the hole pattern on the firebox with the pattern on the
smoker chamber. The firebox should be slightly offset from the smoker
chamber. Attach using six 1/4-20x3/4” hex-head bolts and flat washer
inside firebox and 1/4-20 flange nuts inside smoker chamber.
Smoker
chamber
Cover plate
Firebox
NOTE: Smoker chamber door not pictured for clarity.
From inside the smoker chamber, slide the smokestack through the large hole. Align the two holes in the smokestack plate with
the holes in the chamber and secure with two 1/4-20x3/4” hex-head bolts outside the chamber and 1/4-20 flange nuts inside.
8
Smokestack
Smokestack plate
Download from Www.Somanuals.com. All Manuals Search And Download.
Attach wood handle to smoker chamber door using two 1/4-20x3” screws, flat washers, handle spacers and 1/4-20 flange
nuts, as shown below. Repeat to attach handle to firebox door.
9
Smoker chamber
door
Handle spacer
Handle
NOTE: Smoker chamber door not pictured for clarity.
Install grate support screws in the four rear holes and two
front-center holes in the smoker chamber. Use six #10-24x1”
screws and #10 flange nuts.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE: Smoker chamber door not pictured for clarity.
Attach shelf brackets to outer holes on front of smoker chamber
using two 1/4-20x1¼” hex-head bolts and 1/4-20 flange nuts.
DO NOT FULLY TIGHTEN.
11
12
Shelf bracket
NOTE: Smoker chamber door not pictured for clarity.
3rd
1st
Attach two outer
shelf slats. Do not
tighten.
First, attach shelf slats to the two outer holes in shelf brackets using
two #10-24x1” screws and #10-24 flange nuts per slat. DO NOT
FULLY TIGHTEN SCREWS. Second, fully tighten hex-head bolts on
shelf brackets (installed in previous step). Third, attach remaining
shelf slat to brackets with two #10-24x1” screws and #10-24 flange
nuts. FULLY TIGHTEN ALL SHELF SLAT SCREWS.
Attach inner slat.
Fully tighten all
slat screws.
2nd
Tighten bracket bolts.
Download from Www.Somanuals.com. All Manuals Search And Download.
If you have purchased the optional 3” Temperature Gauge,
part number 40003010, remove the attached nut, insert
gauge stem into large hole in cooking chamber door and
attach nut to gauge on inside of door. DO NOT
OVERTIGHTEN NUT. Make sure text and graphics are
aligned for easy viewing.
13
14
If you do not have a temperature gauge, install the chrome
hole plug (provided) into temperature gauge hole in cooking
chamber door.
Hole plug
If you would like to purchase the optional 3” Temperature
Gauge, part number 40003010, call 1-800-232-3398.
Hang grease clip from holes on bottom right side of smoker chamber. A 12 oz. soup or vegetable can will fit nicely into clip to
collect grease.
Grease
clip
Download from Www.Somanuals.com. All Manuals Search And Download.
If logo plate is not already installed, insert logo plate pins into two holes in lower right corner of smoker chamber door. Press
logo plate clips onto pins until snug against inside of door.
15
16
Logo plate
Logo plate clip
NOTE: Smoker chamber door not pictured for clarity.
If you wish to grill in the smoker chamber, place two of the three
wire fire grates into bottom of smoker chamber. Place two large
porcelain cooking grates into chamber, resting them on the grate
support screws.
Wire fire grate (2)
Large porcelain
cooking grate (2)
Download from Www.Somanuals.com. All Manuals Search And Download.
Firebox Fire Grate Installation for Smoking or Grilling:
NOTE: Firebox side door not pictured for clarity.
17
18
Place remaining wire fire grate into bottom of firebox through
side door.
Wire fire grate (1)
Firebox Cooking Grate Installation for Grilling:
NOTE: Firebox door not pictured for clarity.
If you wish to grill in the firebox, install four #10-24x1” screws and
#10-24 flange nuts as grate supports. Insert small porcelain
cooking grate into firebox.
Small porcelain
cooking grate (1)
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE LIST
Hardware is shown actual size. You may have spare hardware after assembly is complete.
Leg Cap
Qty: 2
(Already installed)
Handle Spacer
Qty: 4
Hole Plug
Qty: 1
Logo Plate Clip
Qty: 2
Cotter Pin
Qty: 2
Flat Washer
Qty: 14
(4 already installed)
1/4-20
Flange Nut
Qty: 18
1/4-20
Hex Nut
Qty: 2
(Already installed)
#10-24
Flange Nut
Qty: 24
#8-32
Lock Nut
Qty: 2
1/4-20x3”
Machine Screw
Qty: 4
1/4-20x2”
Machine Screw
Qty: 4
#10-24x1¾”
Machine Screw Hex-Head Bolt Machine Screw Hex-Head Bolt
1/4-20x1¼”
#10-24x1”
1/4-20x3/4”
#8-32x1/2”
Machine Screw
Qty: 2
Qty: 8
Qty: 2
Qty: 16
Qty: 10
(2 already installed)
WARNING
MOST SURFACES ON THIS UNIT ARE HOT WHEN IN USE.
USE EXTREME CAUTION. KEEP OTHERS AWAY FROM UNIT.
ALWAYS WEAR PROTECTIVE CLOTHING TO PREVENT INJURY.
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparing and Using Your Silver Smoker
Before cooking with your Silver Smoker, the following steps should be closely followed to both cure the finish and
season the interior steel. Failure to properly follow these steps may damage the finish and/or impart metallic flavors
to your first foods.
1. Brush all interior surfaces including grills and grates with vegetable cooking oil.
2. Build a small fire on the fire grate, being sure not to lay coals against the walls.
3. Close door. (Position butterfly damper and smokestack damper approximately at one quarter open.) This burn
should be sustained for at least two hours, the longer the better. Then, begin increasing temperature by opening
the butterfly damper and smokestack damper half-way and adding more charcoal. Your Silver Smoker is now
ready for use.
Rust can appear on the inside of your smoker. Maintaining a light coat of vegetable oil on interior surfaces will aid in
the protection of your unit. Exterior surfaces of smoker may need occasional touch up. We recommend the use of a
commercially available black high temperature spray paint. NEVER PAINT THE INTERIOR OF THE UNIT !
GRILLING
Wood is recommended, however charcoal or a combination of both may be used as the fuel source for grilling, with
the fuel source placed and ignited on the fire grate. Do not build too large of a fire. We recommend starting a fire
with no more than 4 pounds of charcoal (approximately 60 briquets) and adding more as needed during cooking.
After allowing the fire to burn down, place the cooking grills in the smoker. Failure to read and follow instructions for
lighting charcoal may result in serious personal injury and/or property damage.
GRILL MAINTENANCE
Frequency of cleanup is determined by how much your smoker is used. Make sure coals are completely
extinguished before cleaning inside of smoker. Inside surfaces may be cleaned with a strong solution of detergent
and water applied with a scrub brush. Thoroughly rinse with water and allow to air dry before using again.
SMOKING AND SLOW COOKING
If using the Silver Smoker as a smoker or slow cooker, remove the cooking grill from the firebox and build your fire on
top of the fire grate in the firebox. Either charcoal or wood may be used, but wood is the recommended fuel for it’s
rate of burn and the flavor it imparts to the food being cooked. Most seasoned hardwoods are good for smoking
such as hickory, mesquite, pecan, oak, and many other fruit woods. The firebox will accommodate most split
fireplace size logs (16”). Bark should be avoided or burned off first as it contains a high acid content and imparts an
acrid flavor.
After allowing the fire to burn down, close the doors and control the temperature and smoke with the dampers located
on the firebox and atop the smokestack. Smoke is contained within the chambers, which will reduce burn while
imparting more smoke flavor. Do not operate the Silver Smoker with temperatures exceeding 450 degrees in the
smoker chamber. Place the food in the smoker chamber and monitor the temperature. Cooking and smoking are
taking place using indirect heat. There is no need to worry about a grease fire flare-up ruining the food. Do not place
food within 6” of the opening from the firebox into the smoker chamber. A general rule of thumb for cooking is about
1 hour per pound for smoking large cuts of meat. Refer to a cook book for specific cuts of meats. Limit the number
of times you open the smoker chamber door as this will allow heat to escape and extend the cooking time.
HELPFUL HINTS
• If food seems to be getting too smoky or brown before the cooking time is finished, cover it loosely with heavy duty
aluminum foil.
• Remove the ash after each use.
• Covered side dishes can be warmed in smoker chamber.
• To prevent flare-ups, brush meat lightly with oil before grilling.
• Keep a small squirt bottle of water handy for grilling flare-ups.
Download from Www.Somanuals.com. All Manuals Search And Download.
Limited Warranty
Charbroil warrants the Silver Smoker for replacement or repair of parts and/or workmanship for a period of 3 months. Charbroil
warrants to the original Silver Smoker owner repair or replacement of the cooking chamber only should "burn out" or "rust through"
occurforaperiodof1year. Paint is not warrantedandwillrequire touchup.
These limited warranties are made exclusively to the original customer presenting proof of purchase. These warranties are limited to
non-commercial usage. Any returned goods must be clearly marked with a Charbroil Return Authorization Number and shipped
prepaid. These limited warranties do not cover normal wear and tear or damages resulting from abuse or misuse. This warranty
excludesincidentalor consequential cost due to damages or lossesorpropertyofanynature.
NOTICE: Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an
implied warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and
youmayalsohaveotherlegal rights which may vary from state to state.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
For warranty service
CALL TOLL FREE
1-800-232-3398
Download from Www.Somanuals.com. All Manuals Search And Download.
|