Chamberlain Home Safety Product 50HERK User Manual

HERKULES MOTION  
DETECTOR  
50HERK  
QuickStart  
PROGRAMMING  
FUNCTION  
PROGRAMMING MOUNTING HEIGHTS  
(Only use if factory default is not desired)  
The Herkules Motion Detector is a microwave sensor sending out  
a high frequency sound wave while listening for bounce back.  
When the sound wave is returned at a different frequency the  
sensor knows that there is a moving object within the detection  
zone. A signal is sent to the internal relay, which is wired to the  
door control’s activation input.  
Without push-button remote:  
1. Open detectors face plate.  
2. Press both buttons "X" and "Y" for 2 seconds, the green LED  
will flash (you are now in programming mode).  
FACTORY DEFAULT SETTINGS  
The Herkules has been pre-programmed to the following settings  
to make the installation easier and user friendly. If settings need  
to be changed refer to manufacturer’s instructions.  
Y
Mounting Height . . . . . . . . . . . . . .13' to 16' above the  
ground  
Relay Hold Interval 1 . . . . . . . . . .2 seconds output  
X
Slow Motion Detection . . . . . . . . .Medium detection  
(detects very slow objects)  
3. Press "X" button 2 times.  
Separation People and Vehicles . .ON  
4. Press "Y" button for the desired height:  
2 times for 8' to 9.5'  
Cross Traffic Detection . . . . . . . . .Medium  
Direction Recognition . . . . . . . . . .Forward (movement toward  
the detector)  
3 times for 9.5' to 12.5'  
4 times for 12.5' to 16'  
5 times for 16' to 19'  
6 times for 19' to 22.5'  
7 times for 22.5' to 23'  
NOTE: If other settings are desired, then they can be changed by  
using the optional remote control or with the internal push  
buttons in the detector.  
With (optional) remote:  
ADDRESSING THE SENSOR  
1. Point the remote at the motion detector.  
2. Press "G" the Start key.  
This assists in programming and reduces interference if multiple  
units are used on the same location.  
1. Open cover to motion detector.  
2. Find Dip switches.  
3. Adjust Dip switches.  
3. Press "F" and then press the following number to set the  
height:  
#2 once for 8' to 9.5'  
#3 once for 9.5' to 12.5'  
#4 once for 12.5' to 16'  
#5 once for 16' to 19'  
#6 once for 19' to 22.5'  
#7 once for 22.5' to 23'  
Address  
Switch 1  
Off  
Switch 2  
Off  
Address 1  
Address 2  
Address 3  
Address 4  
On  
Off  
On  
Off  
On  
On  
4. When you press the number for the desired height, the  
lighted button will stay on indicating the programming is  
complete. If the button flashes, then the sensor did not accept  
the program.  
O 1  
2
2
2
N
Address 1  
Address 2  
Address 3  
O 1  
N
O 1  
N
Address Dip Switch  
O 1  
2
N
Address 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Beyerdynamic Headphones DT770 pro User Manual
Black Decker Saw 3335 User Manual
BlueTrek Bluetooth Headset EN300 328 02 User Manual
BOXLIGHT Projector MP 350m User Manual
Cabletron Systems Network Card SWPIM BRI User Manual
Cabletron Systems Router 3G User Manual
Cambridge Audio DVD Player DVD99 User Manual
Cardinal Gates Pet Fence XTG User Manual
Cavalry Storage Washer Dryer CADA C32A User Manual
Chromalox Thermostat PK425 2 User Manual