Celestron Telescope 1510 User Manual

C80-HD Refractor Telescope  
C102-HD Refractor Telescope  
C114-HD Reflector Telescope  
C150-HD Reflector Telescope  
CG-4 Equatorial Mount  
Models #21077 / #21016 / #31027 / #31056 / #91510  
INSTRUCTION MANUAL  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
C114-HD & C150-HD  
8.  
23.  
22.  
21.  
9.  
10.  
18.  
11.  
20.  
12.  
13.  
14.  
19.  
15  
25.  
16.  
17.  
24.  
Figure 1C  
CG-4 EQ Mount  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
INTRODUCTION  
Congratulations on your purchase and welcome to the Celestron world of astronomy. If you’re a newcomer  
to the hobby of astronomy, some of the terms and telescope components described in this instruction  
manual may be new to you. This manual is designed to instruct you in the proper use of your Celestron C80-  
HD Refractor, C102-HD Refractor, C114-HD 4.5 Newtonian or C150-HD Newtonian as well as the CG-4  
Equatorial Mount. To assist you in assembling and operating your telescope, take time to review this  
manual and the parts diagram listed in Figure 1.  
WARNING—NEVER LOOK AT THE SUN WITH YOUR TELESCOPE OR ITS FINDERSCOPE.  
PERMANENT AND IRREVERSIBLE EYE DAMAGE MAY RESULT AS WELL AS DAMAGE  
TO YOUR TELESCOPE.  
HOWEVER, YOU MAY ENJOY LOOKING AT THE SUN IF YOU HAVE A SAFE METHOD OF  
DOING SO—A SOLAR FILTER. IF USING THE SOLAR FILTER, MAKE SURE THE  
FINDERSCOPE IS COVERED.  
TELESCOPE ASSEMBLY  
The telescopes and all items are packed in one box. Included are:  
Telescope Optical Tube  
German Equatorial Mount  
Adjustable Aluminum Tripod  
6x30 Finderscope and Bracket  
Counterweight Shaft and Counterweights (3.6 Kg and 1.8 Kg for reflector models #31027, #31056  
and refractor model #21016; 3.6 kg only for refractor model #21077 and CG-4 Eq Mount #91510)  
Tripod Accessory Tray  
Declination Slow Motion Knob  
Right Ascension Slow Motion Knob  
20mm Plossl Eyepiece  
1 ¼" Mirror Diagonal (Except #31027 & #31056)  
Setting Up the Tripod:  
1. Locate the tripod head (see figure 1). Attach each leg one by one to the tripod head by aligning the  
holes at the top of each leg with the holes in the tripod head. Slide a bolt through each of the legs and  
the tripod head and secure at the other end with a wing nut. NOTE: this may have been pre-assembled  
at the factory.  
2. Now that the tripod legs are attached, stand the tripod up and spread the legs until the center leg  
support is fully extended.  
3. The equatorial mount, which holds the telescope, attaches to the tripod head. On one side of the tripod  
head there is an “N” which signifies North. This side of the tripod will face north when setting up for  
an astronomical observing session. Above the “N” is a metal peg about 3/4" high that points straight  
up. Place the equatorial mount head on top of the tripod head so that the metal peg fits between the two  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
azimuth adjustment bolts. It may be necessary to partially unscrew the bolts to allow the metal peg to  
fully extend into the altazimuth housing.  
4. Tighten the knob located on the underside of the tripod head. This will hold the equatorial mount  
firmly to the tripod head.  
Attaching the Accessory Tray  
Next, attach the accessory tray to the tripod. Locate the accessory tray and the three wingnut screws to  
attach the tray.  
1. Place the accessory tray on the center support brace of the tripod and align the holes on the tray with  
those on the support brace.  
2. Insert the wingnut screws through the bottom of the tripod support brace and thread them into the  
accessory tray holes.  
With the accessory tray in place, the tripod will be much more stable, making it easier to attach the  
telescope.  
Installing the Counterweight Bar  
With the mount securely in place, you are ready to attach some of the accessories (the telescope  
tube will be added last). Start with the Counterweight Bar and Counterweights. Used to balance  
the telescope, the Counterweight Bar attaches to the opposite side of the mount as the telescope.  
To install the Counterweight Bar:  
Retract the counterweight bar lock nut by turning it counterclockwise. This will expose the threads  
on the end of the Counterweight Bar.  
Thread the Counterweight Bar into the mount completely. It threads into the mount opposite the  
telescope.  
1. Tighten the lock nut fully for added support.  
2. The Counterweight Bar is now installed.  
3. Installing the Counterweights  
With the counterweight bar in place, you are ready to attach the counterweights.  
1.  
Remove the safety thumbscrew on the end of the counterweight bar.  
2.  
Loosen the counterweight lock screw (on the counterweight itself) so that the central hole  
of the counterweight is unobstructed.  
3.  
Slide the counterweight onto the counterweight bar. Move it high enough to allow room  
for the second weight (if included).  
4.  
5.  
6.  
Tighten the counterweight lock screw to hold it in position.  
Repeat this process for the second weight.  
Replace the thumbscrew on the end of the counterweight bar. The thumbscrew will  
prevent the counterweight(s) from sliding off the bar should they ever become loose.  
Attaching the Optical Tube  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Before you attach the optical tube, make sure that the declination and right ascension clamps are  
tight. The optical tube attaches to the mount via two rings that are mounted on the tube of the  
telescope. To mount the telescope tube:  
1.  
Loosen the knobs on the side of the rings. This will allow you to slide the mounting rings  
the length of the optical tube.  
2.  
3.  
Locate the two screws on either end of the platform for the optical tube (#8).  
Hold the telescope up to the mount and slide the mounting rings until they are over the screws on  
the mounting platform.  
4.  
Place the flat portion of the ring over the mount so that the hole in the ring is over the screw  
protruding out of the mounting platform.  
5.  
Tighten the knobs underneath the mounting platform to secure the rings.  
6.  
Tighten the knobs on the side of the mounting rings to prevent the telescope from sliding  
forward or backward. These can be loosened later to reposition the telescope during the  
balancing process.  
Balancing the Telescope  
To eliminate undue stress on the mount, the telescope should be properly balanced around the polar axis. In  
addition, proper balancing is crucial for accurate tracking if using a clock drive. To balance the mount:  
1. Release the R.A. Clamp and position the telescope off to one side of the mount (see figure 2a).  
2. GRADUALLY release the telescope to see which way it “rolls.”  
3. Loosen a counterweight lock screw and slide the counterweight to a point where it balances the  
scope (i.e., the telescope remains stationary when the R.A. clamp is released).  
4. Tighten the counterweight lock screw.  
The scope is properly balanced in right ascension.  
Figure 2a  
Figure 2b  
The telescope should also be balanced in declination to prevent any sudden movement when the Declination  
clamp is released. To balance the telescope in Declination:  
1. Release the R.A. clamp and rotate the telescope so that it is on one side of the mount (i.e., as described  
above for balancing the mount in R.A.).  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. Lock the R.A. clamp to hold the telescope in place.  
3. Release the DEC clamp and position the telescope so that it is parallel to the ground.  
4. GRADUALLY release the telescope tube to see which way it “rolls.”  
5. Loosen the screws that hold the telescope inside the mounting rings and slide the telescope either forward or  
backwards until it remains stationary when the DEC clamp is released (see figure 2b).  
6. Tighten the screws that hold the telescope in the mounting rings.  
The telescope is now properly balanced in declination.  
Attaching the Finderscope (for #21077, #21016 & #31056)  
To install the finderscope onto the telescope you must first mount the finderscope through the  
finder bracket and then attach it to the telescope. Toward the front of the telescope tube, near the  
focusing assembly, there is a small bracket with a set screw in it. This is where the finderscope  
bracket will be mounted. To install the finderscope:  
1. Slide the rubber O-ring over the eyepiece end of the finderscope and roll it 2/3 of the way up the  
finderscope.  
2. Insert the eyepiece end of the finderscope through the bracket until the O-ring presses tightly between  
the finder and the inside of the bracket.  
3. Tighten the three adjustment screws until they make contact with the finderscope body.  
4. Locate the mounting bracket near the front (open) end of the telescope.  
5. Loosen the set screw on the mounting bracket on the telescope.  
6. Slide the finder bracket (attached to the finderscope) into the mounting bracket on the telescope.  
7. The finderscope bracket will slide in from the back. The finderscope should be oriented so that the  
objective lens is toward the front (open) end of the telescope (see figure 3).  
8. Tighten the set screw on the mounting bracket to hold the finderscope in place.  
Figure 3  
Attaching the Finderscope (for #31027)  
1. Remove the nuts from the studs where the finderscope will mount (see figure 4).  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. Mount the finderscope bracket (#4) by mounting the bracket over the studs protruding from the  
tube and tightening it down with the supplied nuts.  
3. Slide the rubber O-ring over the eyepiece end of the finderscope and roll it 2/3 of the way up the  
finderscope.  
4. Insert the eyepiece end of the finderscope through the bracket until the O-ring presses tightly  
between the finder and the inside of the bracket.  
5. Tighten the three adjustment screws until they make contact with the finderscope body.  
The finderscope is now installed and only needs to be aligned before it is used.  
Figure 4  
Attaching the Accessories  
In order to use your telescope there are some standard accessories which must first be installed:  
The installation of each is described  
1 ¼" Diagonal (for #21077 & #21016): Loosen the thumb screw on the eyepiece holder located on the  
focuser draw tube. Slide the smaller end of the diagonal (without the thumb screw) into the focuser tube.  
Tighten the thumb screw to hold the diagonal in place.  
Ocular: Loosen the thumb screw on the eyepiece holder (or 1 ¼" diagonal for #21077 & #21016). Slide  
the barrel of the eyepiece into the eyepiece holder and tighten the thumb screw to hold the eyepiece in  
place.  
Aligning the Finderscope  
Accurate alignment of the finderscope makes it easy to find objects with the telescope, especially  
celestial objects. To make aligning the finderscope as easy as possible, this procedure should be  
done in the daytime when it is easy to find and identify objects. To align the finder:  
1.  
2.  
3.  
4.  
Choose a target that is in excess of one mile away. This will eliminate any possible parallax effect  
between the telescope and finderscope.  
Point the telescope at your target and center it in the main optics of the telescope. You may have  
to move the telescope slightly to center your target.  
Adjust the screws on the finderscope bracket, tightening one while loosening another, until the  
cross hairs are centered on the target seen through the telescope.  
Tighten the lock nuts to secure the position of the finderscope.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Image orientation through the finder will be inverted (i.e., upside down and backwards left-to-right). This is  
normal for any finderscope that is used straight-through. Because of this, it may take a few minutes to  
familiarize yourself with the directional change each screw makes on the finderscope.  
Telescope Basics  
Calculating Magnification  
The magnification (or power) of a telescope is variable depending upon the focal length of the eyepiece  
being used along with the focal length of the telescope.  
To calculate the magnification we use the following formula:  
FL(telescope)  
Magnification =  
FL(eyepiece)  
where FL(telescope) is the focal length of the telescope and FL(eyepiece) is the focal length of the  
eyepiece. For example, if the focal length of the telescope is 910mm and you use a 20mm eyepiece  
your magnification is 910/20 = 46x.  
There are numerous optional eyepieces that are available to expand your range of magnification. There  
are various types of eyepieces of varying quality to choose from.  
The Celestial - Coordinate System.  
The celestial-coordinate system is an imaginary projection of the Earth's geographical coordinate system  
onto the celestial sphere which seems to turn overhead at night. This celestial grid is complete with equator,  
latitudes, longitudes and poles.  
The Earth is in constant motion as it rotates on its axis. Actually the celestial-coordinate system is being  
displaced very slowly with respect to the stars. This is called precession and is caused by gravitational  
influences from the Sun, Moon and other celestial bodies.  
The celestial equator is a full 360º circle bisecting the celestial sphere into the northern celestial hemisphere  
and the southern celestial hemisphere. Like the Earth's equator, it is the prime parallel of latitude and is  
designated 0º.  
The celestial parallels of latitude are called "coordinates of declination (Dec.)", and like the Earth's  
latitudes they are named for their angular distances from the equator. These distances are  
measured in degrees, minutes and seconds of arc. There are 60 minutes of arc in each degree,  
and 60 seconds of arc in each arc minute. Declinations north of the celestial equator are "+" and  
declinations south are "-". The north pole is +90 and the south pole is -90 .  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
The celestial meridians of longitude are called  
"coordinates of right ascension (R.A.)", and like the  
Earth's longitude meridians they extend from pole to  
pole. There are 24 major RA. coordinates, evenly  
spaced around the 360º equator, one every 15º. Like  
the Earth's longitudes, R.A. coordinates are a measure  
of time as well as angular distance. We speak of the  
Earth's major longitude meridians as being separated  
by one hour of time because the Earth rotates once  
every 24 hours (one hour = 15°). The same principle  
applies to celestial longitudes since the celestial sphere  
appears to rotate once every 24 hours. Right  
ascension hours are also divided into minutes of arc  
and seconds of arc, with each hour having 60 minutes  
of arc and each arc minute being divided into 60 arc  
seconds.  
Figure 5  
Astronomers prefer the time designation for R.A.  
coordinates even though the coordinates denote locations on the celestial sphere, because this makes it  
easier to tell how long it will be before a particular star will cross a particular north-south line in the sky.  
So, R.A. coordinates are marked off in units of time eastward from an arbitrary point on the celestial  
equator in the constellation Pisces. The prime R.A. coordinate which passes through this point is  
designated "O hours O minutes O seconds". We call this reference point the vernal equinox where it  
crosses the celestial equator. All other coordinates are names for the number of hours, minutes and seconds  
that they lag behind this coordinate after it passes overhead moving westward.  
Given the celestial coordinate system, it now becomes possible to find celestial objects by translating their  
celestial coordinates using telescope pointing positions. For this you use setting circles for R.A. and Dec. to  
find celestial coordinates for stellar objects which are given in star charts and reference books.  
Polar Alignment  
Polar alignment is the process by which the telescope’s axis of rotation is aligned (made parallel)  
with the Earth’s axis of rotation (see figure 7). Once aligned, a telescope with a motor drive will  
track the stars as they move across the sky. The result is that objects being observed through the  
telescope appear stationary (i.e., they will not drift out of the field of view). If your telescope does  
not use a motor drive, all celestial objects in the sky (day or night) will slowly drift out of the field.  
This motion is caused by the Earth’s rotation. Even if you are not using a motor drive, polar  
alignment is still desirable since it will reduce the number of corrections needed to follow an object  
and limit all corrections to one axis (R.A.). There are several methods of polar alignment, all of  
which work on a similar principle, but are performed somewhat differently.  
For each hemisphere, there is a point in the sky around which all the other stars appear to rotate.  
These points are called the celestial poles and are named for the hemisphere in which they  
reside. For example, in the northern hemisphere all stars appear to move around the north  
celestial pole (see figure 6). When the telescope’s polar axis is pointed at the celestial pole, it is  
parallel to the Earth’s rotational axis.  
Many of the methods of polar alignment require that you know how to find the celestial pole by  
identifying stars in the area. For those in the northern hemisphere, finding the celestial pole is not  
difficult. Fortunately, we have a naked eye star less than a degree away. This star, Polaris, is the  
end star in the handle of the Little Dipper. Since the Little Dipper (technically called Ursa Minor) is  
not one of the brightest constellations in the sky, it may be difficult to locate, especially from urban  
areas. If this is the case, use the two end stars in the bowl of the Big Dipper. Draw an imaginary  
line through them toward the Little Dipper. They will point to Polaris. The position of the Big  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Dipper will change during the year and throughout the course of the night. When the Big Dipper is  
low in the sky (i.e., near the horizon) it may be difficult to locate.  
Figure 6  
Figure 7  
To make finding and tracking the stars easier, a rough polar alignment is required.  
1.  
2.  
3.  
The right ascension (polar) axis should be pointed towards the North Pole (see figure 7).  
The equatorial mount should be level.  
Set the latitude of the telescope to the latitude of your observing location by turning the azimuth  
adjustment screws (#14) on the mount. The latitude of your observing location corresponds to the  
altitude that Polaris will appear to be above the horizon. For example, If you are observing from  
Los Angeles, which has a latitude of 34°, then the celestial pole (and Polaris) will be 34° above the  
northern horizon. All a latitude scale does then is to point the polar axis of the telescope at the  
right elevation above the northern (or southern) horizon.  
4.  
Release the DEC clamp and move the telescope so that the tube is parallel to the polar  
axis. When this is done, the declination setting circle will read +90°. If the declination  
setting circle is not aligned, move the telescope so that the tube is parallel to the polar  
axis.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5.  
Using the altitude and azimuth adjustment screws (#14 & #20), move the mount until Polaris is in  
the field of view of the finderscope. Rough adjustments in azimuth can be made by moving the  
tripod.  
6.  
Center Polaris using the altitude and azimuth controls. Remember, do not move the telescope in  
R.A. and DEC. You want to adjust the direction the polar axis is pointing and you are using  
the telescope to see where the polar axis is pointing.  
This gets you close to the pole but not directly on it. In order to improve your accuracy for more  
serious observations and photography Celestron offer an optional Polar Axis Finderscope  
(#94221) that fits into the polar axis of the mount.  
Aligning the R.A. Setting Circle  
Before you can use the setting circles to find objects in the sky you need to align the R.A. setting circle.  
The declination setting circle is aligned during the process of polar alignment.  
In order to align the R.A. setting circle, you will need to know the names of a few of the brightest stars in  
the sky. If you don’t, they can be learned by using the Celestron Sky Maps (#93722) or consulting a current  
astronomy magazine.  
To align the R.A. setting circle:  
1. Locate a bright star near the celestial equator. The farther you are from the celestial pole the better your  
reading on the R.A. setting circle will be. The star you choose to align the setting circle with should be a  
bright one whose coordinates are known and easy to look up.  
2. Center the star in the finderscope.  
3. Look through the main telescope and see if the star is in the field. If not, find it and center it.  
4. If you purchased an optional motor drive, start it now so that it will track the star.  
5. Look up the coordinates of the star.  
6. Rotate the circle until the proper coordinates line up with the R.A. indicator (the zero mark on the vernier  
scale). The R.A. setting circle should rotate freely.  
NOTE: Because the R.A. setting circle does NOT move as the telescope moves in R.A., the  
setting circle must be aligned each time you want to use it to find an object. This holds true even  
if you are using an optional motor drive. However, you do not need to use a star each time.  
Instead, you can use the coordinates of the object you are currently observing.  
Once the setting circles are aligned you can use them to find any objects with known coordinates. The  
accuracy of your setting circles is directly related to the accuracy of your polar alignment.  
1. Select an object to observe. Use a seasonal star chart to make sure the object you chose is  
above the horizon. As you become more familiar with the night sky, this will no longer be  
necessary.  
2. Look up the coordinates in an atlas or reference book.  
3. Hold the telescope and release the DEC clamp.  
4. Move the telescope in declination until the indicator is pointing at the correct declination coordinate.  
5. Lock the declination clamp to prevent the telescope from moving.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6. Hold the telescope and release the R.A. clamp.  
7. Move the telescope in R.A. until the indicator points to the correct coordinate.  
8. Lock the R.A. clamp to prevent the telescope from slipping in R.A. The telescope will track in R.A. as  
long as the motor drive is operating.  
9. Look through the finderscope to see if you have located the object.  
10. Center the object in the finder.  
11. Look in the main optics and the object should be there. For some of the fainter objects, you may not be able  
to see them in the finder. When this happens, it is a good idea to have a star chart of the area so that you  
can “star hop” through the field to your target.  
This process can be repeated for each object throughout any given night.  
Using the R.A. Vernier Scale  
To increase the accuracy of the R.A. setting circle, the mount comes with a vernier. This device allows you  
to get more precise readings down to one minute of right ascension.  
Before we go into the specifics on how to use the vernier, let’s take a look at the scale and learn how to read  
it. First, the zero (0) mark on the vernier is the R.A. indicator and will hereafter be referred to as such. It is  
on the extreme right end of the vernier scale with the other numbers increasing as you move toward the left.  
If the R.A. indicator is right on one of the marks of the R.A. setting circle, then that is the coordinate the  
telescope is pointing at. The problem arises when the R.A. indicator (zero mark) is in between two of the  
marks on the R.A. setting circle. If this is the case you will notice that along the vernier scale, one of the  
marks will line up with one of the marks on the setting circle. This mark indicates the number of minutes  
that should be added to the R.A. reading of the indicator. Since the indicator is between two R.A. marks,  
add the minutes to the lower value that the R.A. indicator falls between.  
h
m
For example, let’s say the R.A. indicator (zero mark on the vernier) is just left of the 5 40 mark. This  
h
m
h
m
would place it between the 5 40 mark and the 5 50 mark. If you look down the vernier scale, you will  
see that the “4” is the only mark to line up with any of the marks on the R.A. setting circle (see figure 8).  
h
m
h
m
This means that you are 4 minutes to the left of the 5 and 40 mark or more simply at 5 and 44 .  
Figure 8  
Here’s how to use the vernier:  
1. Look up the coordinates of the object you want to observe. For our example we will use the Ring Nebula  
h
m
(M57) which is at 18 53 right ascension.  
h
m
2. Release the R.A. clamp and rotate the telescope until the R.A. indicator is between the 18 50 mark and  
h
m
the 19 00 mark on the R.A. setting circle.  
3. Lock the R.A. clamp to hold the telescope in place.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. Move the telescope in R.A. using the slow motion control handle until the three on the vernier scale lines up  
with one of the marks on the R.A. setting circle. Remember, the R.A. indicator must stay between the  
h
m
h
m
18 50 mark and the 19 00 mark on the R.A. setting circle!  
5. Look through the telescope and the Ring Nebula should be within the field of view if you are using a low  
power eyepiece (assuming you have already set the DEC).  
Telescope Maintenance  
With proper care your telescope should rarely need any maintenance work.  
1. When not in use, always replace all lens covers to keep dust and contaminants off the optical surfaces.  
2. A small amount of dust on any optical surface is OK. If the dust builds up then use a can of  
compressed air and then a camel's hair brush to remove the dust.  
3. If the mirrors or lenses need cleaning, they should be cleaned by a professional. Either have your  
instrument serviced by a telescope repair facility or return it to the factory.  
4. Collimation or alignment of the optical system is done at the factory before shipment.  
Collimation (for the #31027 and #31056 only)  
1. If your telescope has received very rough handling during transport or is dropped, it may need  
collimation.  
To check if your telescope is in collimation the sketch below will help you. If you look into the  
eyepiece adapter (without an eyepiece), this is what you should see. If the reflection of your eye is  
off center, then collimation is necessary.  
2. If your telescope is out of collimation, it can be re-collimated by loosening the three Phillips head  
screws located on the rear cell of the telescope tube and adjusting the three knurled knobs until the  
secondary mirror is centered in the reflection of the primary mirror.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The best way to re-collimate is with a good collimation tool. Celestron offers a Newtonian Collimation Tool  
(#94183) with detailed instructions that make it an easy chore.  
Technical Specifications  
C80-HD (#21077) C102-HD  
(#21016)  
C114-HD  
(#31027)  
Newtonian  
Reflector  
C150-HD  
(#31056)  
Newtonian  
Reflector  
Optical System:  
Coating:  
Achromat  
Refractor  
Achromat  
Refractor  
Fully Multi-Coated Fully Multi-  
Coated  
Multi Coated  
Multi Coated  
Aperture:  
Focal Length:  
F/ratio:  
80mm  
900mm  
f/11  
45x  
189x  
1.45  
131  
12  
1.1°  
57’  
102mm  
1000mm  
f/10  
114mm  
900mm  
f/8  
150mm  
1000mm  
F/7  
50x  
354x  
0.77  
459  
13.5  
1°  
53’  
Magnification (with standard eyepiece)  
Highest Useful Power Magnification:  
Resolution in arc seconds (Dawes)  
Light Gathering Power:  
Limiting Visual Magnitude:  
Angular Field of View:  
Linear Field of View (at 1000 yds.)  
Optical Tube Length:  
50x  
45x  
241x  
1.14  
212  
12.5  
1°  
53’  
269x  
1.02  
265  
13  
1.1°  
57'  
35"  
38.5"  
35"  
19.25”  
Weight  
Optical Tube:  
Equatorial Mount (with counterweight):  
6 lbs.  
23 lbs.  
8.0 lbs.  
28 lbs.  
6 lbs.  
28 lbs.  
13 lbs.  
28 lbs.  
Note: All specifications are using the standard accessories. These specifications are approximate  
and subject to change without notice.  
OPTIONAL ACCESSORIES  
Celestron International offers a wide assortment of optional accessories to expand your interests.  
Sky Maps (#93722) - Invaluable when learning the night sky. They include all the constellations with the  
brighter deep-sky objects. On the front cover is a rotating planisphere which indicates when specific  
constellations are visible.  
Flashlight - LED (#93588) - Uses red LED's to allow reading star maps and locating telescope accessories  
and controls without ruining you night vision.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Motor Drive (#93517) - This single-axis unit runs off D-cell batteries. It compensates for the Earth's  
rotation keeping celestial objects centered in the field of view. This makes observing much more enjoyable  
as it eliminates the constant usage of the slow motion controls. A dual-axis model (#93522) is also  
available.  
Eyepieces - A whole assortment of various sizes of 1 - 1/4" eyepieces are available to give you a wide range  
of magnifications.  
Eyepiece filters - A line of filters are available for 1-1/4" eyepieces to enhance your visual observations of  
the Moon and planets.  
Collimation Tool for Newtonians (#94183) - A helpful aid to collimating your telescope. Provided is a  
simple tool and detailed instructions.  
Polar Axis Finderscope (#94221) – This useful accessory helps speeds accurate polar alignment by using  
an etched reticle for finding the North Celestial Pole.  
T-Adapters - Allows you to take short exposure photos of the Moon. It requires a 35mm SLR camera and a  
T-Ring for your brand of camera.  
Other - Numerous other accessories are available. See the Celestron Accessory Catalog (#93685) or ask  
your Celestron dealer for details.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CELESTRON TWO YEAR WARRANTY  
A. Celestron warrants this telescope to be free from defects in materials and workmanship for two years. Celestron will repair or  
replace such product or part thereof which, upon inspection by Celestron, is found to be defective in materials or workmanship.  
As a condition to the obligation of Celestron to repair or replace such product, the product must be returned to Celestron  
together with proof-of-purchase satisfactory to Celestron.  
B. The Proper Return Authorization Number must be obtained from Celestron in advance of return. Call Celestron at (310) 328-  
9560 to receive the number to be displayed on the outside of your shipping container.  
All returns must be accompanied by a written statement setting forth the name, address, and daytime telephone number of the  
owner, together with a brief description of any claimed defects. Parts or product for which replacement is made shall become  
the property of Celestron.  
The customer shall be responsible for all costs of transportation and insurance, both to and from the factory of  
Celestron, and shall be required to prepay such costs.  
Celestron shall use reasonable efforts to repair or replace any telescope covered by this warranty within thirty days of receipt. In  
the event repair or replacement shall require more than thirty days, Celestron shall notify the customer accordingly. Celestron  
reserves the right to replace any product which has been discontinued from its product line with a new product of comparable  
value and function.  
This warranty shall be void and of no force of effect in the event a covered product has been modified in design or  
function, or subjected to abuse, misuse, mishandling or unauthorized repair. Further, product malfunction or  
deterioration due to normal wear is not covered by this warranty.  
CELESTRON DISCLAIMS ANY WARRANTIES, EXPRESS OR IMPLIED, WHETHER OF MERCHANTABILITY OF  
FITNESS FOR A PARTICULAR USE, EXCEPT AS EXPRESSLY SET FORTH HEREIN.  
THE SOLE OBLIGATION OF CELESTRON UNDER THIS LIMITED WARRANTY SHALL BE TO REPAIR OR REPLACE  
THE COVERED PRODUCT, IN ACCORDANCE WITH THE TERMS SET FORTH HEREIN. CELESTRON EXPRESSLY  
DISCLAIMS ANY LOST PROFITS, GENERAL, SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES WHICH MAY  
RESULT FROM BREACH OF ANY WARRANTY, OR ARISING OUT OF THE USE OR INABILITY TO USE ANY  
CELESTRON PRODUCT. ANY WARRANTIES WHICH ARE IMPLIED AND WHICH CANNOT BE DISCLAIMED  
SHALL BE LIMITED IN DURATION TO A TERM OF TWO YEARS FROM THE DATE OF ORIGINAL RETAIL  
PURCHASE.  
Some states do not allow the exclusion or limitation of incidental or consequential damages or limitation on how long an  
implied warranty lasts, so the above limitations and exclusions may not apply to you.  
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.  
Celestron reserves the right to modify or discontinue, without prior notice to you, any model or style telescope.  
If warranty problems arise, or if you need assistance in using your telescope contact:  
Celestron  
Customer Service Department  
2835 Columbia Street  
Torrance, CA 90503  
Tel. (310) 328-9560  
Fax. (310) 212-5835  
Monday-Friday 8AM-4PM PST  
This warranty supersedes all other product warranties.  
NOTE: This warranty is valid to U.S.A. and Canadian customers who have purchased this product from an Authorized  
Celestron Dealer in the U.S.A. or Canada. Warranty outside the U.S.A. and Canada is valid only to customers who  
purchased from a Celestron Distributor or Authorized Celestron Dealer in the specific country and please contact them for  
any warranty service  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Black Decker Vacuum Cleaner VC2500 User Manual
Blue Rhino Electric Heater 82300C User Manual
Bodum Coffee Grinder 5670 User Manual
Bolens Tiller 215 418 000 User Manual
Briggs Stratton Lawn Mower RIDER 11 User Manual
Briggs Stratton Portable Generator 30361 User Manual
Brother Sewing Machine XE3725 1011 User Manual
Casio Electronic Keyboard GZ 5 User Manual
Christie Digital Systems Projector DS+650 User Manual
Cisco Systems Network Card CE 100T 8 User Manual