MA0412-EA
Operation Guide DQ-960/961
ILLUSTRATION
1
1
DQ-961
DQ-960
3
4
5
6
3
HUMIDITY
MAX/MIN
T E M P.
MAX/MIN
9
4
3
7
6
3
5
SET
2
CLEAR
F
°
C/
°
CLEAR
°C/°F
T E M P. HUMIDITY
MAX/MIN MAX/MIN
DOWN
(–)
UP
(+)
SNZ
ON
OFF
UP (
+
)
DOWN (—)
ALM
SET
RESET
SNZ
ON
SNZ
ON
OFF
2
SET
CL
ALM
F
°
E
A
C/
°
R
OFF
T
E
M
P. HUMIDITY
DOWN
(–)
UP
(+)
7
8 9
SNZ
ON
MAX/MIN MAX/MIN
OFF
ALM
ALM
HUMIDITY
MAX/MIN
T
E
M
P.
RESET
MAX/MIN
RESET
CLEAR
°C/°F
UP
(
+
)
DOWN (—)
SET
8
RESET
• A sticker is affixed to the glass of the clock when you purchase it. Be sure to remove the sticker before using the
clock.
• Depending on the clock model, the configuration of your clock may differ somewhat from that shown in the
illustration.
Alarm Off
DATE (month - date) Day of the week
Snooze Alarm On
Alarm on indicator
Snooze on indicator
Alarm time
PM indicator
Current time
(Hour, minutes, seconds)
Current Temperature
Current Humidity
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Guide DQ-960/961
USING THE LIGHT
HYGROMETER FUNCTIONS
Pressing the SNOOZE/LIGHT button (1) turns on the light and illuminates the display for easy reading in the dark.
A built-in sensor measures humidity and shows the measured value on the display.
Important!
• Overuse of the light can shorten battery life.
Humidity Measurements
• The humidity display shows “LO” for humidity below 10% and “HI” for humidity above 90%.
High Humidity and Low Humidity Memory
• The clock remembers the high and low humidity values it measured since the last time its humidity memories
were cleared. You can recall these values as shown below.
THERMOMETER FUNCTIONS
A built-in sensor measures temperature and shows the measured value on the display. The readout from the
temperature sensor can also be switched between Celsius (°C) and Fahrenheit (°F).
Current temperature
and humidity
High humidity
and low humidity
Temperature Measurements
• The temperature display shows “LO” for temperatures below –50°C (–58°F) and “HI” for temperatures above
70°C (158°F).
• Though temperature readings are displayed up to 0°C (32°F) and greater than 41°C (105°F), note that such
readings are actually outside the guaranteed temperature range of this clock.
Switching between Celsius and Fahrenheit
• Push the °C/°F button (4) to select either Celsius (°C) or Fahrenheit (°F).
MAX/MIN HUMIDITY button (9)
Celsius (°C)
Fahrenheit (°F)
• To clear the high humidity and low humidity memory, press the MAX/MIN HUMIDITY button (9) to display the
current high/low values, and then press the CLEAR button (6). Note that the current high/low values are
displayed for only about five seconds, and you need to press the CLEAR button (6) during that period.
°C
°F
°C/°F button (4)
High Temperature and Low Temperature Memory
• The clock remembers the high and low temperatures it measured since the last time its temperature memories
were cleared. You can recall these values as shown below.
CLEAR button (6)
Current temperature
and humidity
High temperature
and low temperature
BATTERY REPLACEMENT
Replace batteries whenever the display of the clock becomes dim and difficult to read.
1. Open the battery compartment cover as shown in the illustration.
2. Remove all of the old batteries.
3. Load a full set of new batteries. Make sure that their positive (+) and negative (–) ends face in the correct
directions. If you load batteries incorrectly, they can burst and damage the clock.
4. Replace the battery compartment cover.
MAX/MIN TEMP. button (7)
5. Press the RESET button (8). Be sure to press the RESET button (8) after replacing batteries.
• To clear the high temperature and low temperature memory, press the MAX/MIN TEMP. button (7) to display the
current high/low values, and then press the CLEAR button (6). Note that the current high/low values are
displayed for only about five seconds, and you need to press the CLEAR button (6) during that period.
New data starts to be stored after memory is cleared.
Battery precautions
• Keep batteries out of the reach of small children. If a battery is accidentally swallowed, contact your physician
immediately.
• Be sure to load the batteries with their positive (+) and negative (–) ends facing correctly.
• Never mix old and new batteries, or batteries of different brands.
• Never charge the batteries that come with the clock.
• Should batteries ever leak while in the clock, wipe out the fluid with a cloth, taking care not to let any get onto
your skin.
• Replace the batteries at least once a year, even if the current batteries are working properly.
• The batteries that come with the clock lose some of their power during transport and storage.
CLEAR button (6)
3
Download from Www.Somanuals.com. All Manuals Search And Download.
|