Casio Watch 2213 User Manual

2211/2213/2215-1  
Module No. 2211/2213/2215  
GENERAL GUIDE  
Press C to change from mode to mode.  
Pressing E in any mode besides the Alarm Mode illuminates to the display for about three seconds. The backlight is disabled while a setting screen is on the display.  
If you do not perform any operation for a few minutes while a setting screen (with flashing digits) is on the display, the watch automatically exits the setting screen.  
If you do not perform any operation for a few minutes in any mode besides stopwatch mode, the watch automatically reverts to the normal timekeeping screen.  
Timekeeping Mode  
Day Counter Mode  
Alarm Mode  
Stopwatch Mode  
Memo Mode  
Press C.  
ABOUT THE BACKLIGHT  
TIMEKEEPING MODE  
Month  
Day  
Press D to toggle between 12-hour and 24-hour time-  
keeping.  
With 12-hour timekeeping, times between midnight and  
noon are indicated by A (am), while times between noon  
and midnight are indicated by P (pm).  
The A and P indicators do not appear for 24-hour time-  
keeping.  
About the Auto Light Switch Function  
When the auto light switch function is turned on, the backlight automatically turns on  
for two seconds under the conditions described below. Avoid wearing the watch on  
the inside of your wrist. Doing so causes the auto light switch to operate when not  
needed, which shortens battery life.  
Day of week  
Moving the watch to a position that is parallel to the ground and then tilting it  
towards you approximately 40 degrees causes the backlight to illuminate.  
Pressing B plays a randomly selected melody. To stop  
a playing melody, press any button besides E.  
Pressing E while a melody is playing toggles the dis-  
play between an animated character and the name of  
the melody.  
Seconds  
Minutes  
PM indicator  
Hour  
See the “MELODY LIST” for the names of melodies.  
Parallel to ground  
40°  
Press E to illuminate the display for about three sec-  
onds. When 12-hour timekeeping is being used, press-  
ing E also displays an animated character.  
DST indicator 2  
Timekeeping Mode Settings  
The backlight may not illuminate if the face of the watch is more than 15 degrees off  
parallel to the left or right. Make sure that the back of your hand is parallel to the  
ground.  
In addition to settings for the current time and date, the Timekeeping Mode setting  
screen also lets you turn button tones and melody play on and off, adjust tones and  
melody volume, and adjust display contrast.  
Parallel to ground  
More than 15 degrees  
too high  
More than 15 degrees  
too low  
To make Timekeeping Mode settings  
1. While in the Timekeeping Mode, hold down A until the seconds digits flash on the  
display, indicating the setting screen.  
2. Press C to move the flashing in the sequence shown below. Press E to move the  
flashing in the opposite direction.  
Press  
.
Press  
.
Static electricity or magnetic force can interfere with proper operation of the auto  
light switch function. If the auto backlight does not illuminate, try moving the watch  
back to the starting position (parallel with the ground) and then tilt it back toward  
you again. If this does not work, drop your arm all the way down so it hangs at your  
side, and then bring it back up again.  
Under certain conditions the backlight may not light until about one second or less  
after turning the face of the watch towards you. This does not necessarily indicate  
malfunction of the backlight.  
Seconds  
DST  
Hour  
Minutes  
Day  
Year  
Contrast  
(CNT)  
Volume  
(VOL)  
Sound  
(SOUND)  
Month  
3. While the seconds setting is selected (flashing), press  
D or B to reset it to 00.  
DST indicator 1  
To switch the auto light switch function on and off  
In the Timekeeping Mode, hold down D for two seconds to turn the auto light switch  
function on and off.  
If you press D or B while the seconds setting is in the  
range of 30 to 59, the seconds are reset to 00 and 1 is  
added to the minutes. If the seconds setting is in the  
range of 00 to 29, the minutes count is unchanged.  
While the DST (Daylight Saving Time) setting is selected,  
press D or B to toggle it on and off.  
Auto light switch  
indicator  
DST indicator 1 is displayed in the Timekeeping Mode  
setting screen only when the DST setting is selected. It  
shows ON when the DST setting is on, and OFF when  
the DST setting is off.  
DST indicator 2 is displayed in the Timekeeping Mode,  
Day Counter Mode and Alarm Mode when the DST set-  
ting is turned on.  
Hold down D.  
ON  
OFF  
The auto light switch indicator is shown on the display in all modes while the auto  
light switch function is on.  
In order to protect against running down the battery, the auto light switch function is  
automatically turned off approximately three hours after you turn it on. Repeat the  
above procedure to turn the auto light switch function back on if you want.  
Pressing E in any mode besides the Alarm Mode illuminates the display for about  
three seconds, regardless of the auto light switch’s on/off setting.  
DST indicator 2  
While the SOUND setting is selected, press D or B to turn the beep and musical  
tone on and off, as shown below.  
Press  
.
Press  
.
Caution  
The backlight of this watch employs an electro-luminescent (EL) light, which loses  
its illuminating power after very long term use.  
Frequent use of the backlight shortens the battery life.  
The watch emits an audible sound whenever the display is illuminated. This is  
because the EL light vibrates slightly when lit. It does not indicate malfunction of  
the watch.  
Musical tone  
Off  
Beep  
While the VOL setting is selected, press D or B to toggle it between loud and soft.  
Press or  
Warning!  
Never try to read your watch when mountain climbing or hiking in areas that  
are dark or in areas with poor footing. Doing so is dangerous and can result  
in serious personal injury.  
.
Never try to read your watch when running where there is the danger of acci-  
dents, especially in locations where there might be vehicular or pedestrian  
traffic. Doing so is dangerous and can result in serious personal injury.  
Never try to read your watch when riding on a bicycle or when operating a  
motorcycle or any other motor vehicle. Doing so is dangerous and can result  
in a traffic accident and serious personal injury.  
When you are wearing the watch, make sure that its auto light switch function  
is turned off before riding on a bicycle or operating a motorcycle or any other  
motor vehicle.  
Soft  
Loud  
While the CNT setting is selected, press D to make the display darker, or B to  
make it lighter.  
While any other setting is selected (flashing), press D to increase it or B to de-  
crease it. Holding down either button changes the setting at high speed.  
4. After you make the settings you want, press A to exit the setting screen.  
The day of the week is automatically set in accordance with the date.  
The date can be set within the range of January 1, 2000 to December 31, 2039.  
The watch's built-in full automatic calendar automatically makes allowances for dif-  
ferent month lengths and leap years.  
Sudden and unintended operation of the auto light switch can create a dis-  
traction, which can result in a traffic accident and serious personal injury.  
Once you set the date, there should be no reason to change it except after the  
replacement of the watch's battery.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2211/2213/2215-3  
STOPWATCH MODE  
CHARACTER LIST  
Mode indicator  
The stopwatch Mode lets you measure elapsed time, split  
times, and two finishes. The range of the stopwatch is 23  
hours, 59 minutes, 59.99 seconds. You can use the EL  
backlight by pressing E at any time while the stopwatch  
is operating.  
Current time  
Hours  
Minutes  
Seconds  
1/100 second  
Elapsed time measurement  
MELODY LIST  
Stop  
Split time measurement  
Re-start  
Stop  
Stop  
Clear  
Clear  
Start  
2211  
1
2
3
4
5
Purple haze  
Rock and roll  
Burn  
Split  
Split time and 1st-2nd place times  
Split release  
Start  
Every breath you take  
Born in the U.S.A.  
Split  
Stop  
Split release  
Record time of  
second runner.  
Clear  
Start  
First runner  
finishes.  
Second runner  
finishes.  
Record time of  
first runner.  
2213  
MEMO MODE  
1
2
3
4
5
Fantasy  
Mode indicator  
The Memo Mode lets you store up to five memos, each  
with an eight-character title and 16 characters of data.  
YMCA  
Title  
Happy birthday  
Ai no corrida  
Billie jean  
Recalling a Memo  
In the Memo Mode, press D to scroll through the Memo  
titles. When you find the title you want, press B, and the  
screen alternates between the title and data.  
The display can show only five characters at a time.  
Longer text scrolls continuously from right to left. The  
symbol “ ” indicates that the character or digit to the  
left is the last, and the character or digit to the right is  
the first.  
A series of hyphens “ – – – – – ” is displayed for a memo  
that does not contain any data. The display can show  
only five characters at a time.  
2215  
Memo number  
1
2
3
4
5
Katte ni Sindbad  
Rydeen  
To input a memo  
1. In the Memo Mode, press D to display the memo number you want to set.  
2. Hold down A until the first (leftmost) character of the memo title starts to flash on  
the display. This indicates the input screen.  
2 oku 4 semman no hitomi  
Marionette  
3. Press C to move the flashing in the sequence shown below. Press E to move the  
flashing in the opposite direction.  
Press  
.
Press  
.
Innocent world  
Title Character 1  
Title Character 8  
Data Character 1  
Data Character 16  
4. Use D or B to scroll through characters at the current location of the flashing.  
Holding down either button scrolls at high speed.  
Press  
.
Press  
.
Space  
A to Z  
Punctuation  
Symbols  
Japanese  
characters  
Hyphen  
Numbers  
See the “CHARACTER LIST” for details.  
Pressing D and B at the same time while inputting memo title or data clears all title  
and data. At this time the message “CLEAR” appears on the display.  
5. After you input the data you want, press A to exit the input screen.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Billion Electric Company Network Card BiGuard 50G User Manual
Black Decker Vacuum Cleaner 724196 User Manual
Blanco Indoor Furnishings 509 337 User Manual
Bolens Lawn Mower 188 421 000 User Manual
Bostitch Nail Gun LPF21PL User Manual
Briggs Stratton Portable Generator 40297 User Manual
Brother Sewing Machine CS 100T User Manual
Canon Camera Lens 0344B002 User Manual
Canon Digital Camera 1V User Manual
Cisco Systems Network Card PPWR DCARD 16ESW User Manual