E
DATA PROJECTOR
XJ-450
User’s Guide
Keep this manual in a safe place for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Precautions
Safety Precautions
Thank you for selecting this CASIO product. Be sure to read these “Safety
Precautions” before trying to use it. After reading this User’s Guide, keep it in a
safe place for future reference.
About safety symbols
Various symbols are used in this User’s Guide and on the product itself to ensure
safe use, and to protect you and others against the risk of injury and against
material damage. The meaning of each of the symbols is explained below.
This symbol indicates a condition that, if ignored or applied
Danger
incorrectly, creates the risk of death or serious personal injury.
This symbol indicates a condition that, if ignored or applied
incorrectly, could possibly create the risk of death or serious
personal injury.
Warning
This symbol indicates a condition that, if ignored or applied
incorrectly, could possibly create the risk of personal injury or
material damage.
Caution
Icon Examples
A triangle indicates a situation against which you need to exercise
caution. The example shown here indicates you should take precaution
against electric shock.
A circle with a line through it indicates information about an action that
you should not perform. The specific action is indicated by the figure
inside the circle. The example shown here means disassembly is
prohibited.
A black circle indicates information about an action that you must
perform. The specific action is indicated by the figure inside the circle.
The example shown here indicates you must unplug the power cord from
the power outlet.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Precautions
Precautions During Use
Warning
GSmoke, odor, heat, loud noise,
and other abnormalities
Should you ever notice smoke,
strange odor, or loud noise being
emitted by the projector, or any
other abnormality, immediately
stop using the projector.
GPower cord
Misuse of the power cord creates
the risk of fire and electric shock.
Make sure that you always
observe the following precautions.
•
Make sure that you use a
power source with the same
voltage as that specified for
the projector.
Continued use creates the risk of
fire and electric shock.
•
Do not overload a power outlet
with too many devices.
Immediately perform the following
steps.
GPower cord
A damaged power cord creates
1. Unplug the projector.
2. Contact your original dealer or
authorized CASIO service
center.
the risk of fire and electric shock.
Make sure that you always
observe the following precautions.
GMalfunction
•
Never place heavy objects on
the power cord and never
expose it to heat.
Immediately stop using the
projector if the screen appears
abnormal, if sound is not
produced, or if any other
abnormal operation occurs even
though you are operating the
projector correctly. Continued use
creates the risk of fire and
electric shock. Immediately
perform the following steps.
•
Make sure the power cord is
not pinched between the wall
and the rack or table where
the projector is located, and
never cover the power cord
with a cushion or other object.
Never try to modify the power
cord, allow it to become
damaged, or subject it to
excessive bending.
•
•
1. Turn off the projector.
2. Unplug the projector.
3. Contact your original dealer or
authorized CASIO service
center.
Do not twist the power cord or
pull on it.
GPower cord
Never touch the power cord or
plug while your hands are wet.
Doing so creates the risk of
electric shock.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Precautions
3. Contact your original dealer or
authorized CASIO service
center.
GWater and foreign matter
Never allow water to get on the
projector. Water creates the risk
of fire and electric shock.
GDisposal by burning
Never place a vase or any other
container of water on top of the
projector. Water creates the risk
of fire and electric shock.
Water or other liquid, or foreign
matter (metal, etc.) getting into
the projector creates the risk of
fire and electric shock. Should
anything get inside the projector,
immediately perform the following
steps.
Never try to dispose of the
projector by burning it. Doing so
can cause an explosion, which
creates the risk of fire and
personal injury.
GLooking into the lens or vents
while lamp is on
Never look directly into the lens
or vents while lamp is on. The
strong light emitted by the
projector creates the risk of eye
damage.
1. Turn off the projector.
2. Unplug the projector.
GBlocking the vents
Never allow the intake vents (on
the bottom or back of the
3. Contact your original dealer or
authorized CASIO service
projector) or the exhaust vents
(on the side of the projector) to
become blocked. Doing so
causes internal heat build up,
which creates the risk of fire and
breakdown of the projector.
Touching the projector while it is
hot creates the risk of burn
injury. Make sure that you always
observe the following precautions.
center.
GDisassembly and modification
Never try to take the projector
apart or modify it in any way.
The projector contains a large
number of high-voltage
components that create the risk
of electric shock and burn injury.
Be sure to leave all internal
inspection, adjustment, and repair
up to your original dealer or
authorized CASIO service center.
GDropping and impact
Continued use of the projector
after it has been damaged by
dropping or other mistreatment
creates the risk of fire and
electric shock. Immediately
perform the following steps.
•
Allow at least 30 cm (11.8
inches) between the projector
and walls.
•
Do not insert the projector into
any space where air circulation
is poor.
•
•
Never cover the projector with
a blanket or any similar item.
Never use the projector on a
carpet, blanket, towel, or other
soft material.
1. Turn off the projector.
2. Unplug the projector.
•
Never stand the projector up
on either end during use.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Precautions
GProjector cabinet
GHeavy objects
Never open the projector’s
Never place heavy objects on the
projector or climb on top of the
projector. Doing so creates the risk of
fire and electric shock.
cabinet. Doing so creates the risk
of electric shock.
GCleaning
GWater
Before cleaning the projector, be
sure to turn it off and unplug it
from the power outlet. Failure to
do so creates the risk of electric
shock.
Never locate the projector in a
bathroom or anywhere else there is the
chance that it will be splashed with
water.
GExhaust vents
GUnstable location
The exhaust vents become very hot
while the projector is running. Never
touch them. Doing so creates the risk
of burn injury. The areas near the
exhaust vents also become quite hot.
Never locate objects made of plastic or
other heat-sensitive materials near or
under the projector. Doing so creates
the risk of deformation and discoloration
of the object.
Never place the projector on an
unstable surface or on a high
shelf. Doing so can cause it to
fall, creating the risk of personal
injury.
GUsing the projector on a base
with casters
Whenever using the projector on a base
that has casters, make sure that you
lock the casters when not moving the
base.
GFront cover
Be sure to open the front cover before
turning on the projector. Never close the
front cover while the projector is in use.
GLocation
Never locate the projector in any of the
following types of locations. Doing so
creates the risk of fire and electric
shock.
GLightening
During a lightening storm, do not touch
the plug of the projector’s power cord.
GRemote controller
Never try to take the remote
controller apart or modify it in
any way. Doing so creates the
risk of electric shock, burn injury,
and other personal injury. Be
sure to leave all internal
inspection, adjustment, and repair
up to your original dealer or
authorized CASIO Service Center.
Never allow the remote controller
to become wet. Water creates
the risk of fire and electric shock.
•
•
•
•
Near an area subject to strong
vibration
An area subject to large
amounts of moisture or dust
In a kitchen or other area
exposed to oil smoke
Near a heater, on a heated
carpet, or in an area exposed
to direct sunlight
•
An area subject to temperature
extremes (Operating
temperature range is 5°C to
35°C (41 to 95 °F)).
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Precautions
Caution
GPower cord
GBackup of important data
Be sure to keep separate written
records of all data stored in
projector memory. Memory data
can be lost due to breakdown,
maintenance, etc.
Misuse of the power cord creates
the risk of fire and electric shock.
Make sure that you always
observe the following precautions.
•
•
Do not locate the power cord
near a stove.
When unplugging the power
cord, always grasp the plug,
and do not pull on the power
cord.
GLens effect
Never have an aquarium or any other
object that produces a lens effect in
front of the projector while the lamp is
on. Such an object creates the risk of
fire.
GPower cord
Misuse of the power cord creates
GLens
the risk of fire and electric shock.
Make sure that you always
Never touch the lens with your hand.
observe the following precautions.
•
Insert the plug into the power
outlet as far as it will go.
•
After using the projector, turn
it off and allow it to cool
down. Next, unplug it from the
power outlet.
•
•
Unplug the projector from the
power outlet if you do not plan
to use it for a long time.
To avoid the built up of dust
between the prongs of the
plug, unplug it from the power
outlet and clean between the
prongs at least once a year.
Before moving the projector, be
sure to turn it off and unplug
it from the power outlet first.
•
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Precautions
Battery Precautions
Warning
Caution
Misuse of batteries can cause them to
leak and stain the area around them,
or to explode, creating the risk of fire
and personal injury. Make sure that you
always observe the following
Misuse of batteries can cause them to
leak and stain the area around them,
or to explode, creating the risk of fire
and personal injury. Make sure that you
always observe the following
precautions.
precautions.
•
Never try to take batteries
apart and do not allow them
to become shorted.
•
Use only the type of batteries
that is specified for the remote
controller.
•
•
•
Never expose batteries to heat
or throw them into fire.
Never mix old batteries and
new ones.
Never mix batteries of different
types.
Never try to charge batteries.
Take care that batteries are
oriented correctly when you
load them.
GDead batteries
Be sure to remove batteries from the
remote controller as soon as they go
dead.
•
Remove batteries from the
remote controller if you do not
plan to use it for a long time.
•
•
GDisposing of batteries
Make sure that you dispose of used
batteries in accordance with the rules
and regulations in your local area.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Precautions
Lamp Precautions
Warning
Caution
GLamp removal
GLamp replacement
Never remove the lamp from the
Before replacing the lamp, be
projector immediately after using
it. The lamp becomes very hot
during use, creating the risk of
burn injury. Turn off the projector.
After the POWER/STANDBY
indicator changes to steady (not
flashing) amber, unplug the
projector from the power outlet.
Next, wait for at least 60 minutes
before removing the lamp.
sure to turn off the projector and
unplug it from the power outlet.
Failure to do so creates the risk
of electric shock.
•
Take care when replacing a
broken lamp.
A broken lamp can cause
glass fragments to be
scattered inside the lamp
housing. Glass inside of the
lamp housing may also be
discharged from the projector’s
vent exhaust ports. Gas inside
of the lamp includes mercury,
so be sure to ventilate the
area whenever the lamp
breaks. Should you accidentally
inhale gas fumes or should
gas fumes get into your eyes,
immediately contact a
GSpecified lamp type
Use only the lamp type that is
specified for this projector. Use of
any other type of lamp creates
the risk of fire and breakdown.
physician.
GBroken lamp
Never attempt to replace a
broken lamp on your own. The
projector uses a mercury lamp
with high internal pressure as its
light source. Should the lamp
break, be sure to contact your
original dealer or authorized
CASIO service center to request
replacement. Attempting to
replace a broken lamp on your
own creates the risk of personal
injury due to broken glass or
dispersed mercury.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Precautions
Operating Precautions
Lamp Handling Precautions
G Continued use of a lamp that has passed its lamp life
increases the risk of the lamp rupturing. Replace the lamp
with a new one as soon as possible after the replacement
message appears.
Caution
G Never touch the glass of the lamp with your fingers. Doing so can damage the
lamp and shorten its life.
G The light source lamp is a consumable item. The average life of a lamp is
approximately 2000 hours. After 2000 hours, a message appears to alert you to
the need of lamp replacement. However, note that the characteristics of a
particular lamp or lamp operating conditions can cause the lamp to start to go
dim or even fail before the message appears.
G Lamps are guaranteed for 90 days from the date of purchase or for 500 hours
operation, whichever comes first.
G A mercury lamp with high internal pressure is used as the light source. A lamp
that is weakened by impact, damage, or expiration of its lamp life may explode
or fail to light if exposed to loud noise. Note that the performance of the lamp
differs greatly from lamp to lamp, and due to conditions under which a lamp is
used.
G The replacement message appears and the LAMP indicator flashes red after the
lamp life is reached. When this happens, replace the lamp using the instructions
provided in this User’s Guide.
G If the lamp continues to be used after its lamp life is reached, after 100 hours
the projector will enter a cool down state and then go into standby. The
projector will not turn on again until you replace the lamp.
Lamp Replacement Precautions
G When the lamp life is reached, the message “It is time to replace the lamp.
Use the procedure in the User’s Guide to replace the lamp as soon as
possible.” appears on the display for about 10 seconds, and the LAMP indicator
starts to flash red in one-second intervals. Replace the lamp as soon as
possible after the message appears or the LAMP indicator flashes.
G Replace the lamp with a special YL-40 replacement lamp, which should be
available from your original dealer.
G Turn off the projector. After the POWER/STANDBY indicator changes to steady
(not flashing) amber, unplug the projector from the power outlet. Next, wait for
at least 60 minutes before removing the lamp. Note that the lamp cartridge
becomes very hot during normal use and during standby. Handling it when hot
creates the risk of burn injury.
G The lamp contains mercury. Dispose of old lamps in accordance with the rules
and regulations of your local jurisdiction.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Precautions
G When replacing the lamp, use the special screwdriver that comes with the YL-40
replacement lamp.
Other Precautions
This projector is made of precision components. Failure to observe the following
precautions can result in inability to correctly save data and malfunction.
GNever use or store the projector in the following locations. Doing so
creates the risk of malfunction of and damage to the projector.
•
•
•
•
•
•
•
Locations subjected to electrostatic
charge
Locations subjected to temperature
extremes
Locations where there is extreme
moisture
Locations subjected to sudden
temperature changes
Locations where there is a lot of
dust
On a shaky, slanted, or otherwise
unstable surface
Locations where there is the danger of getting wet
GAvoid using the projector under the following conditions. Such
conditions create the risk of malfunction of and damage to the
projector.
•
Avoid areas subject to temperature extremes
(operating temperature range is 5°C to 35°C
(41 to 95 °F)).
•
•
•
Never place heavy objects on the projector
or climb on top of the projector.
Never insert or allow foreign objects to drop
into the projector.
Never place a vase or any other container of
water on top of the projector.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Precautions
GNever leave dead batteries inside the remote controller for a long
time.
Batteries can leak, which leads to malfunction of and damage to the remote
controller.
GClean with a soft, dry cloth.
When very dirty, use a soft cloth that has been dampened in a weak solution of
water and a mild neutral detergent. Wring all excess water from the cloth before
wiping. Never use thinner, benzene, or any other volatile agent to clean the
projector. Doing so can remove its markings and cause staining of the case.
GMissing Screen Dots
Though this projector is manufactured using the most advanced digital technology
available today, some of the dots on the screen may be missing. This is normal,
and does not indicate malfunction.
•
•
The contents of this User’s Guide are subject to change without notice.
Copying of this manual, either in part or its entirety, is forbidden. You are
allowed to use this manual for your own personal use. Any other use is
forbidden without the permission of CASIO COMPUTER CO., LTD.
CASIO COMPUTER CO., LTD. shall not be held liable for any lost profits or
claims from third parties arising out of the use of this product or this manual.
CASIO COMPUTER CO., LTD. shall not be held liable for any loss or lost
profits due to loss of data caused by malfunction or maintenance of this
product, or any other reason.
•
•
•
The sample screens shown in this manual are for illustrative purposes only,
and appear differently from the screens actually produced by the product.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
About safety symbols........................................................................................ 3
General Guide................................................................................................. 24
Loading Remote Controller Batteries.............................................................. 27
Using the Laser Pointer................................................................................... 28
Setting Up the Projector.................................................................................. 30
Adjusting the Projector Elevation Angle.......................................................... 35
Rear Projection (From the Back of the Screen) .............................................. 37
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Setup Menu Overview..................................................................................... 64
Volume Adjustment...................................................................................... 82
Projector Troubleshooting............................................................................. 122
Specifications................................................................................................ 124
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Features and Functions
Features and Functions
The following are some of the major features and functions of this product.
I278 × 64 × 197 mm (10.9 × 2.5 × 7.8 inch), 2.4 kg (5.3 lbs)
lightweight and compact data projector
Though it is compact and lightweight enough to go just about anywhere, the projector’s high-
luminosity (2800ANSI lumen) allows clear projection of images, even in a brightly lit room.
IAuto Focus, auto vertical and horizontal keystone correction
The press of a key automatically focuses the image and performs vertical and horizontal
keystone correction for a perfect projected image.
IPower zoom and power focus
Zooming and focusing of the projected image can be performed using the remote controller.
ILaser pointer built into the remote controller
The remote controller unit also doubles as a laser pointer. During a presentation, you can
use the pointer to indicate items within the projected image.
IVersatile projection range
The shortest projection distance is 0.8 meters (2.62 feet), which means that very little space
is required for projection. 2X zoom makes it possible to produce a projected image of the
size you want from a range of possible distances. To project onto a 60-inch screen, for
example, you can set up the projector anywhere from 1.6 meters (5.25 feet) to 3.2 meters
(10.5 feet) from the screen.
IA selection of possible input sources
Possible input sources are a computer’s RGB signal, a video device’s VIDEO/S-VIDEO signal,
and a component video signal (Y·Cb/Pb·Cr/Pr).
IVersatile projection functions
A collection of powerful projection tools let you enlarge a specific part of the projected image
with digital zoom, use picture-in-picture to insert a video input sub-window into a projected
computer image, and much more.
IRemote controller also performs computer mouse functions
You can use the remote controller that comes with the projector to perform mouse operations
on the computer connected to the projector’s USB port, to perform page up and page down
operations, and more. The remote controller helps to make presentations more effective.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
General Guide
General Guide
This section defines the names and explains the main functions of each part of the projector.
[Front/Top/Left side]
1
2
(4Cover open)
3
4
5
6
7
1 Speaker
: Outputs audio input through the AUDIO terminal.
)[Back, Terminals] (page 19)
2 Key and Indicator Panel
: This panel includes the [ ] (power) key and various
indicators.
)[Key and Indicator Panel] (page 21)
3 Exhaust vents
: Exhaust air for cooling.
)Setup Precautions (page 33)
z
Never allow the exhaust vents to become blocked, and make sure
there is at least 30 cm (11.8 inches) clearance around the
projector. Blocked vents can cause heat to build up, creating the
risk of fire and malfunction.
Warning
z
Never touch the areas around the exhaust vents. These areas can
become very hot, and create the risk of burn injury.
4 Front cover
: Protects the projection lens. Slide the cover open to
extend the lens before turning on the projector.
5 Remote control signal receiver : Receives the remote control signal.
)Remote Controller Signal Range (page 29)
16
Download from Www.Somanuals.com. All Manuals Search And Download.
General Guide
6 Lens
: Projects the image from the projector.
Never look into the lens while the projector is turned on.
Warning
7 Sensors
: Measures the distance between the projector and screen.
z
Finger smudges or dirt on the sensors can cause keystone
correction problems. Should the sensors ever become soiled, wipe
them clean using a commercially available lens cloth or optical lens
paper, like those for eyeglasses or camera lenses.
Caution
17
Download from Www.Somanuals.com. All Manuals Search And Download.
General Guide
[Bottom]
2
1
3
5
4
3
1 Elevation adjustment foot
: Rotate to change the angle of the projector.
)To change the projector elevation angle (page 35)
2 Release button
: Press to release the elevation adjustment foot.
3 Left, right adjustment feet (2) : Rotate for fine adjustment of the left and right angle of
the projector.
)To change the projector elevation angle (page 35)
4 Intake vents
: Intake air for cooling.
)Setup Precautions (page 33)
Never allow the intake vents on the back or the bottom of the projector
to become blocked. Blocked vents can cause heat to build up, creating
the risk of fire and malfunction.
Warning
5 Lamp cover
: Open this cover to replace the lamp.
)To replace the lamp (page 114)
18
Download from Www.Somanuals.com. All Manuals Search And Download.
General Guide
[Back, Terminals]
1
2
3
4
5
6
7
8 9
bk
1 RGB input terminal
: For connection to the video output terminal of a computer
or component video device using the bundled Mini D-Sub
cable or the optional component video cable (YK-3).
)Connecting a Computer to the Projector (Video and Audio) (page 37)
)Connecting to a Component Video Output Device (page 40)
2 USB port
: For connection to a USB port of a computer using the
bundled USB cable.
)Connecting a Computer to the Projector’s USB Port (page 38)
3 Remote control signal receiver : Receives the remote control signal.
)Remote Controller Signal Range (page 29)
4 Projection key panel cover
: Protects a key panel for projection operations.
: Intake air for cooling.
5 Intake vents
)Setup Precautions (page 33)
Never allow the intake vents on the back or the bottom of the projector
to become blocked. Blocked vents can cause heat to build up, creating
the risk of fire and malfunction.
Warning
6 Anti-theft lock hole
: An anti-theft chain can be passed through this hole. Visit
the Kensington Lock Website at http://www.kensington.com/
for more information.
7 VIDEO input terminal
: For connection to the VIDEO output terminal of a video
device using the bundled video cable.
)Connecting to a Standard Video Device (page 39)
8 S-VIDEO input terminal : For connection to the S-VIDEO output terminal of a video
device using a commercially available S-video cable.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
General Guide
9 AUDIO input terminal
: For connection to the audio output terminal of a computer
or video device using a commercially available audio cable
(∅.3.5mm stereo).
)Connecting a Computer to the Projector (Video and Audio) (page 37)
)Connecting to a Standard Video Device (page 39)
bk Power connector
: For connection of the bundled AC power cord.
)Turning On the Projector(page 41)
20
Download from Www.Somanuals.com. All Manuals Search And Download.
General Guide
Using the Projection Key Panel
You can use the keys on the projection key panel to control the projector when the remote
controller is not available for some reason.
Opening and Closing the Projection Key Panel Cover
Hook your finger
here and lift to open.
[Key and Indicator Panel]
1
2
3
TEMP
LAMP
POWER/STANDBY
ZOOM
AF/AK
AUTO
INPUT
4
5
6
7
8
1 TEMP indicator
: Indicates the error status of the projector.
)Indicators and Alert Tones (page 119)
2 LAMP indicator
: Indicates the current lamp status.
)Indicators and Alert Tones (page 119)
)Replacing the Lamp (page 111)
3 POWER/STANDBY indicator
: Indicates the current projector status.
)Turning On the Projector(page 41)
)Indicators and Alert Tones (page 119)
4 [ZOOM] keys
: Press to change the size of the projected image.
)Zoom and Focus (page 50)
21
Download from Www.Somanuals.com. All Manuals Search And Download.
General Guide
5 [AF/AK] key
: Press to perform Auto Focus and auto keystone correction.
)Auto Keystone Correction and Auto Focus (page 53)
6 [AUTO] key : Automatically adjusts the projected image in accordance
with RGB input.
)Auto Adjustment of an RGB Image (page 51)
7 [INPUT] key
: Press to cycle through available projector input sources.
)Manually Selecting the Input Source (page 48)
8 [ ] (power) key
: Turns projector power on and off.
)Turning On the Projector (page 41)
[Projection Key Panel]
1
2
3
MENU
KEYSTONE
ESC
6
ENTER
FOCUS
4
5
1 [MENU] key
: Press this key to display the projector setup menu on the
projected image.
)Using the Setup Menu (page 64)
2 [KEYSTONE] key
: Press this key to automatically correct the projected image
and remove vertical and horizontal keystoning.
)Keystone Correction (KEYSTONE) (page 53)
3 [ESC] key
: Use this key to perform the operations described below.
z When a menu screen is displayed, to back-step to the previous screen ()page 68)
z To perform a mouse right-click operation on the computer connected to the projector’s
USB port. ()page 62)
22
Download from Www.Somanuals.com. All Manuals Search And Download.
General Guide
4 Cursor keys
: Use these keys to perform the operations described below.
z To move the highlighting (selection cursor) on the menu screen ()page 68)
z To perform mouse operations on the computer connected to the projector’s USB por
()page 62)
*In this manual, cursor key operations are indicated as [S], [T], [X], [W].
5 [ENTER] key
: Use this key to perform the operations described below.
z To execute the command currently highlighted on the menu screen ()page 68)
z To perform a mouse left-click operation on the computer connected to the projector’s
USB port. ()page 62)
6 [FOCUS] keys
: Press to adjust focus.
)Zoom and Focus (page 50)
z You can disable certain key operations, if you want. For details, see “Option Settings1 J
Key Lock” on page 94.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Controller
Remote Controller
This section defines the names and explains the main functions of each part of the remote
controller.
General Guide
1
bm
AF/AK
2
3
bn
PAGE
UP
PAGE
DOWN
bo
ENTER
MENU
ESC
4
bp
bq
KEYSTONE
5
6
ZOOM
FOCUS D-ZOOM
7
8
br
bs
bt
RGB
AUTO
MUTE
VIDEO
S-VIDEO
P-IN-P
FREEZE
9
bk
bl
VOLUME
ck
cl
z
z
Keep the remote controller out of the hands of young children, and
never allow a young child to operate the remote controller. The
laser pointer built into the remote controller can cause eye damage
and loss of sight if pointed directly into a person’s eyes.
Never try to take the remote controller apart or modify it in any
way. Doing so creates the risk of electric shock, burn injury, and
other personal injury. Be sure to leave all internal inspection,
adjustment, and repair up to your original dealer or authorized
CASIO Service Center.
Warning
z
Never allow the remote controller to become wet. Water creates
the risk of fire and electric shock.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Controller
z The asterisks (*) in the following explanations indicate keys that have the same names
and functions as keys on the projector itself. Note that the operations of remote controller
keys
,
, and
can be performed using the projector’s [INPUT] key.
8 bs
bt
z Some remote controller keys have the same names as projector keys. Unless stated
otherwise in this manual, the remote controller keys perform the same functions as their
corresponding projector keys.
1 Remote controller signal/laser signal emitter
CLASS 1 LED PRODUCT
2 *[ ] (power) key
: Turns projector power on and off.
)Turning On the Projector (page 41)
3 [PAGEUP] / [PAGEDOWN] keys: Press to perform page up and page down operations on
the computer connected to the projector’s USB port.
)Operating the Computer with the Remote Controller (Wireless Mouse) (page 62)
4 *[ENTER] key
: Use this key to perform the operations described below.
z To execute the command currently highlighted on the menu screen ()page 68)
z To perform a mouse left-click operation on the computer connected to the projector’s
USB port. ()page 62)
5 *[MENU] key
: Press this key to display the projector setup menu on the
projected image.
)Using the Setup Menu (page 64)
6 *[FOCUS S/T] keys
: Press to adjust focus.
)Zoom and Focus (page 50)
7 *[ZOOM +/–] keys
: Press to change the size of the projected image.
)Zoom and Focus (page 50)
8 [RGB] key
: Press to select the RGB input terminal as the input
source.
)Manually Selecting the Input Source (page 48)
9 *[AUTO] key
: Automatically adjusts the projected image in accordance
with RGB input.
)Auto Adjustment of an RGB Image (page 51)
bk [P-IN-P] key
: When projecting RGB (computer) input, press this key to
project video input in a sub-window.
)Using Picture-in-Picture (P-IN-P) (page 59)
bl [MUTE] key
: Press to momentarily cut off the projected image and
audio output from the projector’s speaker.
)Muting the Image and Audio (MUTE) (page 61)
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Controller
bm [LASER] key
: Hold down to emit a laser beam that you can use as a
pointer. The [AF/AK] key lights red while this key is
depressed to indicate that the laser beam is being
emitted.
)Using the Laser Pointer (page 28)
z
z
Never look directly at the laser beam. Doing so creates the risk of
eye damage and loss of sight.
Never point the laser beam at another person. Shining the laser
beam into the eyes of another creates the risk of eye damage and
loss of sight.
Warning
z
Keep the remote controller out of the reach of young children, and
never allow a young child to operate the remote controller.
bn *[AF/AK] key
: Press to perform Auto Focus and auto keystone correction.
)Auto Keystone Correction and Auto Focus (page 53)
bo *Cursor keys
: Use these keys to perform the operations described below.
z To move the highlighting (selection cursor) on the menu screen ()page 68)
z To perform mouse operations on the computer connected to the projector’s USB por
()page 62)
* In this manual, cursor key operations are indicated as [S], [T], [X], [W].
bp *[ESC] key
: Use this key to perform the operations described below.
z When a menu screen is displayed, to back-step to the previous screen ()page 68)
z To perform a mouse right-click operation on the computer connected to the projector’s
USB port. ()page 62)
bq *[KEYSTONE] key
: Press this key to automatically correct the projected image
and remove vertical and horizontal keystoning.
)Keystone Correction (KEYSTONE) (page 53)
br [D-ZOOM +] / [D-ZOOM –] keys: Press the [+] key to increase the size of the projected
image, and the [–] key to decrease it.
)Enlarging the Projected Image (D-ZOOM +/–) (page 57)
bs [VIDEO] key
: Press to select the VIDEO input terminal as the input
source.
bt [S-VIDEO] key
: Press to select the S-VIDEO input terminal as the input
source.
)Manually Selecting the Input Source (page 48)
ck [VOL +] / [VOL –] keys
: Press the [+] key to increase volume, and the [–] key to
decrease volume.
)Adjusting the Volume Level (VOL +/–) (page 56)
cl [FREEZE] key
: Freezes the projected image.
)Freezing the Projected Image (FREEZE) (page 62)
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Controller
Loading Remote Controller Batteries
Before you can use the remote controller for the first time, you need to load the two
batteries that come with it.
z Be sure to use alkaline batteries only.
Replace remote controller batteries with a set of new ones whenever the remote controller
does not work or if you need to move the remote controller very close to the projector before
it will work.
Misuse of batteries can cause them to leak and stain of the area
around them, or to explode, creating the risk of fire and personal
injury. Make sure that you always observe the following precautions.
z
z
z
z
Take care that batteries are oriented correctly when you load them.
Never mix old batteries and new ones.
Never mix batteries of different types.
Use only battery type that is specified for use with the remote
controller.
Caution
To load remote controller batteries
1. Remove the battery cover from the back of the remote controller.
z If there are old batteries inside the case, remove them.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Controller
2. Load two new batteries into the case, making sure that their positive (+)
and negative (–) ends are facing correctly.
3. Replace the battery cover on the back of the remote controller.
Using the Laser Pointer
The remote controller includes a laser pointer that you can use during a presentation to
indicate a specific item within an image. The laser is a 1mW/Class 2 Laser, which qualifies
as a “Designated Specified Product” under Japan’s “Consumer Product Safety Law”.
z
Holding down the [LASER] key causes a red laser beam to be emitted from the front
edge of the remote controller. Use the laser beam to point to the object you want to
indicate in the image.
z
The [AF/AK] key lights red while this key is depressed to indicate that the laser beam is
being emitted.
z
z
Never look directly at the laser beam. Doing so creates the risk of
eye damage and loss of sight.
Never point the laser beam at another person. Shining the laser
beam into the eyes of another creates the risk of eye damage and
loss of sight.
Warning
z
Keep the remote controller out of the reach of young children, and
never allow a young child to operate the remote controller.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Controller
Remote Controller Signal Range
When performing an operation on the remote controller, point it at the remote control signal
port on the back or front of the projector. The following illustration shows the range of the
remote controller signal.
40 degrees
max.
40
degrees max.
9 meters
(29.53 feet) max.
9 meters (29.53
feet) max.
Front
Back
30
30
degrees max.
degrees max.
9 meters (29.53
feet) max.
9 meters (29.53
feet) max.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Ready
Getting Ready
This section explains how to set up the projector to get it ready for use, and how to connect
it to an input source (computer or video device).
It also includes information about how to turn on the projector, how to select the display
language the first time you turn it on, and precautions you need to keep in mind concerning
the power supply.
Setting Up the Projector
Locate the projector on a desk, table, or stand that is firm and level. Make sure to allow
sufficient space around the sides and back of the projector for proper ventilation.
z
The following illustrations show how the projector should be oriented for optimum
projection relative to the screen.
Viewed from Above
Viewed from the Side
Screen
Screen
The center of the projector’s lens
should be aligned with the horizontal
center of the screen.
Make sure the projector is at a right
angle to the screen.
z You can place the projector on a surface that is angled up to 30 degrees up or down
during use. Angling the projector more than 30 degrees up or down can cause rupture
or premature aging of the projector’s lamp, or malfunction of the projector.
z The above setup enables proper projection without any image correction. If the projector
is at an angle to the screen, a phenomenon called “keystoning” will occur, which causes
the sides, and/or the top and bottom of the image to be different lengths. The projector
comes with a keystone correction feature that automatically corrects the image. See
“Keystone Correction (KEYSTONE)” on page 53 for information about keystone correction.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Ready
z
The allowable projection range is from 0.8 meter (2.62 feet) to 16 meters (52.49 feet),
which is the distance from the surface of the lens to the screen.
Screen Size 300
8.0 m to 16.0 m
(26.25 feet to 52.49 feet)
Screen Size 30
0.8 m to 1.6 m
(2.62 feet to 5.25 feet)
Screen Size 60
1.6 m to 3.2 m
(5.25 feet to 10.50 feet)
16 m
14 m
12 m
10 m
8 m
4 m
2 m
6 m
(19.69 feet)
(52.49 feet) (45.93 feet) (39.37 feet) (32.81 feet) (26.25 feet)
(13.12 feet) (6.56 feet)
Minimum: 0.8 meter
(2.62 feet)
Maximum: 16 meters (52.49 feet)
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Ready
The following table shows the relationship between the distance and projected image size.
Projection Size
Projection Distance
Minimum
Distance
(m)
Maximum
Distance
(m)
Minimum
Distance
(feet)
Maximum
Distance
(feet)
Screen Size Diagonal (cm)
30
40
76
102
152
203
254
305
381
508
635
762
0.8
1.6
2.62
5.25
1.1
1.6
2.1
2.7
3.2
4.0
5.3
6.7
8.0
2.1
3.2
3.61
5.25
6.89
10.50
14.11
17.39
21.00
26.25
35.10
43.64
52.49
60
80
4.3
6.89
100
120
150
200
250
300
5.3
8.86
6.4
10.50
13.12
17.39
21.98
26.25
8.0
10.7
13.3
16.0
z
The minimum/maximum distances in the above table define the ranges within which
manual focus is possible. The ranges for Auto Focus and auto keystone correction are
smaller.
z Note that the distances provided above are for reference only. Actual distances will be
within 5% of those provided.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Ready
Setup Precautions
Note that the condition of the environment where you use the projector greatly affects its
performance. Make sure that the following are the conditions of projector setup whenever you
use it.
z
z
z
Use a conveniently located power outlet that you can reach easily when you need to
unplug the projector.
Do not place any objects within the area indicated by the dashed line in the illustration
below. Be especially careful that you never block intake and exhaust vents.
Do not allow the intake vents on the bottom of the projector to become blocked.
30 cm
(11.8 inches)
Exhaust vents
Allow sufficient
clearance and
do not block
intake vents.
Intake vents
Allow sufficient
clearance and do not
block vents.
z
z
Do not locate any objects near the projector while it is in use. Keep all items at least
30 cm (11.8 inches) away from the exhaust vents.
The vents become quite hot while the projector is in use. Never touch the vents with your
hands. Also, the areas near the exhaust vents also become quite hot. Never locate
objects made of plastic or other heat-sensitive materials near or under the projector. Doing
so creates the risk of deformation and discoloration of the object.
z
Avoid placing the projector on a surface that is unstable or prone to vibration. Never
place the projector on top of a carpet, blanket, towel, or other soft material.
Do not locate the projector where it will be exposed to direct sunlight.
Avoid locations where there are large amounts of dust and moisture.
Keep the projector away from speakers, TVs, radios, and other devices that generate
magnetism, as well as from heaters.
z
z
z
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Ready
Projector Angle to the Screen
The following shows the allowable angle that the projector can be positioned relative to the
screen.
Vertical
Horizontal
Screen
Screen
Up to about 30 degrees
Up to about 30 degrees
Up to about 30 degrees
Up to about 30 degrees
z The angles shown in the above illustration are subject to the following conditions.
×
zProjection of an image from a computer (Resolution: 1024 768; Vertical Frequency:
60Hz)
zResize Image To Fit: On
z Actual correction ranges are affected by the type of signal being projected, zoom, the
“Resize Image To Fit” setting, the aspect ratio setting, and other factors.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Ready
Adjusting the Projector Elevation Angle
You can change the elevation angle of the projector in a range of 0 to 8 degrees. You can
also make fine adjustments to the left and right side elevation angle when necessary.
To change the projector elevation angle
1. Lift up the front of the projector and press the release button.
z This causes the elevation adjustment foot to drop from the bottom of the projector.
2. While holding down the release button, raise and lower the front of the
projector until the elevation adjustment foot is approximately the length
you need.
3. Release the release button to lock the elevation adjustment foot in its
current position.
4. Rotate the elevation adjustment foot for fine adjustment of its length.
Longer
Shorter
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Ready
5. Use the left and right adjustment feet to further fine adjust the elevation
angle.
Rotate to adjust horizontal alignment.
z To retract the elevation adjustment foot, hold down the release button and slide the
elevation adjustment foot back into the projector. Never try to forcibly change the elevation
adjustment foot position without pressing the release button.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Ready
Rear Projection (From the Back of the Screen)
Distances and angles for rear projection are the same as those for front projection. In the
case of rear projection, however, left/right orientation is opposite that of front projection, so
you need to configure the setup menu accordingly. For details, see “Screen Settings J
Projection Mode” on page 86.
Connecting a Computer to the Projector
(Video and Audio)
You can use the projector to project an image of video output from a computer. You can also
output audio from the computer through the projector’s speaker.
z Always turn off the projector and the computer before connecting them.
Projector
RGB input terminal
AUDIO input terminal
Computer
Audio cable (commercially available)
To line output terminal
Bundled mini D-Sub cable
To monitor terminal (analog RGB output terminal)
z
z
You can use the bundled mini D-Sub cable to connect to a D-Sub 15-pin type monitor
terminal. For other types of monitor terminals (like the one on the old model Macintosh),
you need to purchase an optional adapter. See the documentation that came with your
computer for information about its terminal.
The analog RGB video output display mode (resolution and frequency combination) of your
computer may not allow proper operation with the projector. See “Supported Signals” on
page 126 for information about the computer display modes supported by this projector.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Ready
Connecting a Computer to the Projector’s
USB Port
After you connect a computer to the projector’s USB port, you can use the remote controller
to perform computer mouse operations, and previous page and next page operations. The
illustration shows how to connect to the USB port.
Projector
USB port
Computer
To USB port
Bundled USB cable
z
z
For details about computer requirements, see “Computer System Requirements for USB
Connection” on page 125.
For details about operation over a USB connection, see “Operating the Computer with the
Remote Controller (Wireless Mouse)” on page 62.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Ready
Connecting to a Standard Video Device
You can use the projector to project an image from a video deck, TV, video camera, or other
video device. You can also output audio from the video device through the projector’s speaker.
z Always turn off the projector and the video device before connecting them.
VIDEO input terminal
S-VIDEO input terminal
AUDIO input terminal
Projector
Commercially available S-video cable
Commercially available audio cable
Bundled video cable
To S-VIDEO output terminal
To VIDEO output terminal
To AUDIO output terminal
Video device
z
z
You can use the bundled video cable to connect to a pin jack (RCA) type VIDEO output
terminal. When connecting a video camera or other video device with a special video
output terminal, use the special cable that comes with the video device. For details, see
the documentation that comes with the video device.
Note that the projector is equipped with separate circuits for the VIDEO input terminal and
S-VIDEO input terminal. Make sure you connect the video device to the correct terminal.
The projector lets you switch the input source between RGB (or Component), VIDEO, and
S-VIDEO whenever you want.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Ready
Connecting to a Component Video Output Device
Some video devices are equipped with a component video output terminal. You can use an
optionally available component video cable (YK-3) to connect the RGB input terminal of the
projector to the component video output terminal of a video device.
z Always turn off the projector and the video device before connecting them.
Projector
RGB input terminal
AUDIO input terminal
Commercially available audio cable
To AUDIO output
terminal
Video device
Optional component video cable
(YK-3)
To Component video
output terminal
z
z
Component video output terminals come in 3-terminal sets: Y·Cb·Cr or Y·Pb·Pr. Be sure to
match the colors of the plugs on the optional YK-3 component video cable with the colors
of the terminals (Green: Y; Blue: Cb/Pb; Red: Cr/Pr).
You can use the optional YK-3 component video cable to connect to pin jack (RCA) type
component video output terminals. The projector does not support connection to any other
type of terminal.
z
z
Note that connection only to an analog component video output terminal is supported.
Connection to a digital output terminal is not supported.
In order to connect to a component video terminal, you must use the setup menu to
configure input settings. For details, see “Input Settings J RGB Input” on page 89.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Ready
Turning On the Projector
Before performing any of the operations in this section, make sure you first set up the
projector (page 30) and connect to an output device (pages 37 to 40).
AC Power Cord Precautions
z
Make sure that you use a power source with the same voltage as that specified for the
projector.
z
Do not share the outlet supplying power to the projector with other devices. If you are
using an extension cord, make sure that the ampere rating of the extension cord is
compatible with the power consumption value of this projector.
Never use the power cord while it is still bundled together.
Never place objects on top of the power cord and do not step on it.
Never pull on the power cord. When unplugging it, grasp the plug.
Use a conveniently located power outlet that you can reach easily when you need to
unplug the projector.
z
z
z
z
z
If you need more information about the power supply, contact your original dealer or
authorized CASIO service center.
To turn on the projector
1. Use the bundled AC power cord to plug the projector into a power
outlet.
Power supply connector
Bundled AC power cord
The shape of the plug depends
on your geographical area.
z Plugging into a power outlet causes the three indicators on the top of the projector to
light amber. After a short while, two of the indicators will go out and only the POWER/
STANDBY indicator will remain lit amber, which indicates the standby state.
z Note that the projector will not turn on if you press the [ ] (power) key while all three
indicators are lit amber. Wait until the projector is in the standby state before trying to
turn it on.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Ready
2. Turn on the computer or video device that is connected to the projector.
3. If the projector’s front cover is closed, open it.
4. Press the [ ] (power) key.
z This causes the POWER/STANDBY indicator to flash green, which indicates that the
projector is warming up. After a short while, the start up screen will be projected (warm
up is still in progress).
z After warm up is complete, POWER/STANDBY indicator stops flashing and remains lit
green, and the projector starts projecting an image from the device connected to it. It
normally takes about 60 seconds from the point that warm up starts until an image is
projected from the connected device.
z A “Language” window will be projected the first time you turn on the projector. Use the
procedure under “Specifying the Display Message Language” on page 43 to configure
the language settings.
Startup screen
Input image projection
z You can configure the startup screen so it shows a custom logo you created yourself, or
so nothing appears at startup. For details, see “Option Settings1 J Custom Logo
Settings” on page 99 and “Screen Settings J Startup Screen” on page 87.
z If the projector is configured for low-noise mode operation, the LAMP indicator lights
green when warm up starts. See “Option Settings1 J Low-noise Mode” on page 93 for
information about the low noise mode.
z For details about projection operations, see “Projecting onto a Screen” on page 46.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Ready
Specifying the Display Message Language
A “Language” window will be projected the first time you turn on the projector. Use the menu
on this screen to specify the display language you want to use.
1. Use the cursor [S] and [T] keys to highlight the language you want to
use.
z
Note that the choice of languages available on the “Language” window will depend on
whether your projector’s serial number starts with the letter A (such as: A791AA42...)
or the letter B (such as: B791AA42...).
If the serial number starts with this
letter:
You can select from among these
languages:
English, French, German, Italian, Spanish,
Swedish, Korean, Japanese,
English, Spanish, Chinese (Simplified),
Chinese (Traditional), Japanese
A
B
A Model
.
B Model
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Ready
2. Press the [ENTER] key.
z This applies the selected language, closes the “Language” window, and displays the
projected image from the connected device.
z You can change the display language selection later, if you need to. For details, see
“Option Settings1 J Language” on page 105.
z For details about projection operations, see “Projecting onto a Screen” on page 46.
Turning Off the Projector
z When you turn off the projector, the lamp goes out and the projector goes into a cool
down state. Note that you will not be able to turn the projector back on again while it is
cooling down.
z The projector may remain quite hot for a while after you turn it off. Avoid touching the
projector after you turn it off.
z Note that the projector may still be quite warm even after it completes its cool down
procedure. Before packing up the projector, it is recommended that you check to make
sure that the fan is stopped and that the projector is no longer warm.
To turn off the projector
1. Press the [ ] (power) key.
z This causes a confirmation message like the one shown below to appear in the center
of the projection screen.
z If you do not turn off the projector the confirmation message will disappear
automatically after about 10 seconds. The confirmation message will also disappear if
you press [ESC] key.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Ready
2. To turn off the projector, press the [ ] (power) key again in response
to the confirmation message.
z This causes the projector lamp to go out and stops projection.
z Also the POWER/STANDBY indicator starts to flash amber, which indicates that the
projector is cooling down. It takes about 120 seconds from the start of cool down until
the projector turns off.
z The projector will not turn back on again while it is cooling down.
z After cool down is finished, the POWER/STANDBY indicator on the top of the projector
will light amber, which indicates the standby state. You can now turn the projector back
on, if you want.
3. After confirming that cool down is complete, unplug the AC power cord
from the power outlet.
z Note that the projector may still be quite warm even after it completes its cool down
procedure. Before packing up the projector, it is recommended that you check to make
sure that the fan is stopped and that the projector is no longer warm.
z This causes the POWER/STANDBY indicator to go out.
4. After ensuring that the projector and the connected computer or video
device are turned off, disconnect the connecting cables from the
projector and the connected device.
5. Close the front cover.
Auto Power Off
Auto Power Off automatically turns off the projector whenever there is no input signal from
the currently selected input source, and no operation is performed on the projector for about
10 minutes.
When Auto Power Off is triggered, the projector first enters a cool down state, the same as
it does when you press the [ ] (power) key to turn it off.
z
The POWER/STANDBY indicator flashes amber to indicate that the projector is cooling
down. It takes about 120 seconds from the start of cool down until the projector turns off.
The projector will not turn back on again while it is cooling down.
After cool down is finished, the POWER/STANDBY indicator on the top of the projector to
lights amber, which indicates the standby state. You can now turn the projector back on,
if you want.
z
z
z You can turn off Auto Power Off, if you want. See “Option Settings1 J Auto Power Off”
on page 94.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Projection Operations
Projection Operations
This section explains operations that are related to projection of an image.
Projecting onto a Screen
This section explains the basic steps for projecting an image.
Basic Flow
Set up the projector and point it at the screen.
) “Setting Up the Projector” (page 30)
Connect the computer or video device to the projector
()page 37 to 40)
Turn on the projector and the connected computer or video device.
Press the [
] (power) key to turn on the projector.
) “Turning On the Projector” (page 41)
Perform fine adjustment of the projection position and angle.
) “Adjusting the Projector Elevation Angle” (page 35)
Select the input source.
) “Manually Selecting the Input Source” (page 48)
Adjust the projected image size and focus the image.
) “Zoom and Focus” (page 50)
Start projection (presentation, video, etc.)
• Perform the required operation on the input source computer or video equipment.
• Use the projector’s various functions to adjust the projected image as required.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Projection Operations
Auto Input Source Selection
When you turn on the projector, it checks the status of each input source (whether or not
the input source is sending a signal) in the sequence shown below. It automatically selects
the first input source it finds that is sending an input signal, and projects the applicable
image.
RGB terminal input
(RGB/Component)
S-VIDEO terminal input
(S-VIDEO)
VIDEO terminal input
(VIDEO)
If the RGB input terminal is connected to a computer and the S-VIDEO input terminal is
connected to a video deck and signals are being supplied by both, for example, the projector
automatically selects RGB input when it is turned on. The currently selected input source
name is shown in the upper right corner of the projection screen.
Input source name
RGB
z If the projector does not find any input signal, the message “No signal input” appears in
place of the input source name.
z Whether the displayed input source name shows [RGB] or [Component] depends on the
current “Input Settings J RGB Input” (page 89) setting that is configured on the
projector’s setup menu.
If the input source name shows this:
RGB
It means this input is selected:
RGB
Component
Component video
For information about configuring setup menu settings, see “Using the Setup Menu” on
page 64. For information about component video, see “Connecting to a Component Video
Output Device” on page 40.
z Note that the projector does not select the input source automatically when “Off” is
selected for the “Option Settings1 J Auto Input Detect” (page 92) setting on the setup
menu.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Projection Operations
Manually Selecting the Input Source
The procedure you should use to select the input source depends on whether you are using
projector keys or remote controller keys.
[Projector]
[Remote Controller]
AF/AK
PAGE
UP
PAGE
DOWN
ENTER
MENU
ESC
KEYSTONE
[S-VIDEO] key
[VIDEO] key
[RGB] key
ZOOM
RGB
FOCUS D-ZOOM
VIDEO
S-VIDEO
AUTO
MUTE
P-IN-P
FREEZE
VOLUME
MENU
KEYSTONE
ESC
ENTER
FOCUS
[INPUT] key
To select the input source using projector keys
On the projector, press the [INPUT] key to cycle through input sources in the sequence
shown below.
(RGB/Component)
(S-VIDEO)
(VIDEO)
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Projection Operations
To select the input source using remote controller keys
On the remote controller, press the [RGB], [VIDEO], or [S-VIDEO] key to select the input
source you want.
z The currently selected input source name is shown in the upper right corner of the
projection screen.
z If the currently selected input source is not sending an input signal, the message “No
signal input” appears in place of the input source name.
z Whether the displayed input source name shows [RGB] or [Component] depends on the
current “Input Settings J RGB Input” (page 89) setting that is configured on the
projector’s setup menu.
If the input source name shows this:
RGB
It means this input is selected:
RGB
Component
Component video
For information about configuring setup menu settings, see “Using the Setup Menu” on
page 64. For information about component video, see “Connecting to a Component Video
Output Device” on page 40.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Projection Operations
Zoom and Focus
Use the [ZOOM] keys to adjust the image size, and the [FOCUS] keys to focus the image.
To adjust image size
1. Hold down the [ZOOM +] key to increase the size of the image or the
[ZOOM –] key to decrease it.
z This causes the zoom indicator, which indicates the current zoom setting, to appear on
the image.
2. Release the [ZOOM] key when the image is the size you want.
z The zoom indicator will disappear from the image automatically if you do not perform
any further key operation for a certain amount of time.
To focus the image
1. Hold down [FOCUS S] or [FOCUS T] to adjust the focus.
z This causes the focus indicator, which indicates the current focus setting, to appear on
the image.
2. When the focus is the way you want, release the [FOCUS] key.
z The focus indicator will disappear from the image automatically if you do not perform
any further key operation for a certain amount of time.
z You can also focus automatically by pressing the [AF/AK] key. For more information, see
“Auto Keystone Correction and Auto Focus” (page 53).
z The focus and zoom indicators may not appear under certain conditions (when the
startup logo is displayed, when the image and audio are muted, during password input,
etc.) Though the indicators do not appear, focus and zoom adjustment can still be
performed by pressing the applicable keys.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Projection Operations
Auto Adjustment of an RGB Image
When the input source is RGB (computer), the projector automatically adjusts vertical and
horizontal positioning, frequency, and phase whenever it detects an RGB signal (following input
source selection, power up, etc.) You can also execute an automatic adjustment operation by
pressing the [AUTO] key.
z You can turn off auto adjustment (page 93) when you want to disable auto adjustment
and maintain manual settings.
z The projected image may become distorted while an auto adjustment operation is in
progress.
z The [AUTO] key is disabled whenever S-VIDEO, VIDEO, or Component is selected as the
input source.
z If an image is unclear following the auto adjustment operation, you can use the menu to
adjust items manually. For details, see “Image Adjustment” on page 77.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Projection Operations
Full-screen Display of an RGB Image
The projector outputs images using XGA (1024 pixels × 768 pixels) video resolution. When
the input signal from the computer connected to the projector is not an XGA signal, “Resize
Image To Fit” automatically enlarges or reduces the image so it matches the projector’s video
resolution and fills the entire screen. The following shows how different input signals from a
computer are adjusted during projection.
Input Signal Example
Projected Image
×
800 600
×
1024 768
×
1280 1024
z Resizing of an input image by “Resize Image To Fit” can call coarsening of the image or
can cause part of the image to be cut off. If this happens, try turning off “Resize Image
To Fit”. See “Screen Settings J Resize Image to Fit” on page 85 for more information.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Projection Operations
Keystone Correction (KEYSTONE)
When the projector is at an angle to the screen it is projecting on, the projected image may
have different length left and right edges, or top and bottom edges. This phenomenon is
called, “keystoning”. This projector comes with functions for automatic as well as manual
keystone correction, which provides a regularly shaped projected image.
z Keystone correction (auto or manual) can cause dustortion of the projected image. If this
happens try moving the screen and/or projector so they are oriented close to the
configuration shown under “Setting Up the Projector” on page 30.
z Depending on the angle between the screen and projector, keystone correction can cause
the corrected image to be smaller than the original (uncorrected) image, or it can cause
deterioration of the image. If keystone correction causes problems with your image,
relocate the screen and/or projector so the line between them is as straight as possible.
Auto Keystone Correction and Auto Focus
Under the initial default configuration of the projector, the AF/AK mode is configured so both
auto keystone correction and Auto Focus are performed when you press the [AF/AK] key. You
can also configure settings of the Continuous AF/AK Mode.
IAF/AK
Auto keystone correction and Auto Focus are enabled when [AF/AK] is selected for
“Option Settings2 J AF/AK Mode” (page 106) on the setup menu. Note that this is the
initial default setting. With this setting, auto keystone correction and Auto Focus are
performed automatically whenever the [AF/AK] key is pressed.
IContinuous AF/AK
Continuous auto keystone correction and Auto Focus are enabled when [Continuous AF/
AK] is selected for “Option Settings2 J AF/AK Mode” (page 106) on the setup menu.
This function comes in handy when it is necessary to project to a surface that is far
away from the projector or at a sharp angle from the projector.
When Continuous AF/AK is enabled, pressing the [AF/AK] key once enters a pre-focus
mode, which displays an alignment chart and starts continuous Auto Focus. Pressing the
[AF/AK] key again performs auto keystone correction.
Note also that the projector automatically enters the Continuous AF/AK mode whenever
projector power is turned on while [Continuous AF/AK] is selected for “Option Settings2 J
Power On AF/AK Mode” (page 107) on the setup menu.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Projection Operations
Performing Auto Keystone Correction and Auto Focus while AF/AK is
Enabled
Perform the following steps while [AF/AK] is selected for “Option Settings2 J AF/AK Mode”
(page 106) on the setup menu.
1. Press the [AF/AK] key.
z This automatically focuses the image and performs auto keystone correction.
Performing Auto Keystone Correction and Auto Focus while
Continuous AF/AK is Enabled
Perform the following steps while [Continuous AF/AK] is selected for “Option Settings2 J AF/
AK Mode” (page 106) on the setup menu.
1. Press the [AF/AK] key.
z This enters the pre-focus mode, which projects an alignment chart like the one shown
below.
z The size of the alignment chart depends on screen and projector setup conditions.
2. Adjust the angle and position of the projector as required so the
projected chart fits within the screen area.
3. Press the [AF/AK] key again.
z This performs auto keystone correction.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Projection Operations
Auto Adjustment at Power On
While [Continuous AF/AK] is selected for “Option Settings2 J Power On AF/AK Mode” (page
107) on the setup menu, turning on the projector automatically enters the pre-focus mode and
projects the positioning chart. Perform the procedure starting from step 2 under “Performing
Auto Keystone Correction and Auto Focus while Continuous AF/AK is Enabled” above.
z When [AF] is selected for “Option Settings2 J AF/AK Mode” on the setup menu, only
Auto Focus is performed when the [AF/AK] key is pressed.
z If the message “Outside of Auto Focus range. Relocate the projector to change the
distance from the screen, and then press the AF/AK button.” appears, try moving the
screen and/or projector so the distance between them is within the auto focus range
(approximately 0.8 to 4 meters). Note that the actual auto focus range will depend on
screen and projector setup conditions, and other factors. When the distance is outside the
auto focus range, use manual focus.
z Note that certain screen and projector conditions, and other environmental factor may
make it impossible to perform auto keystone correction and Auto Focus correctly. In this
case, adjust settings manually.
z Proper Auto keystone correction and Auto Focus are not possible if the projector is not
on a level surface. Make sure you set up the projector correctly, in accordance with the
information under “Getting Ready” (page 30).
Manual Keystone Correction
Manual keystone correction can be used to correct for both vertical and horizontal keystoning.
To use manual keystone correction
1. Press the [KEYSTONE] key.
z This causes the keystone correction screen to appear on the projected image.
2. Use the [S] and [T] keys to select either “Vertical Keystone Correction”
or “Horizontal Keystone Correction”.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Projection Operations
3. Use the [W] and [X] keys to correct for keystoning.
z Each press of [W] or [X] shifts the indicator on the currently selected bar left or right.
z Repeat steps 2 and 3 to perform keystone correction for the other direction, if you
want.
4. After the settings are the way you want, press the [ESC] key or the
[KEYSTONE] key.
z This causes the keystone correction screen to disappear.
z The allowable ranges for manual keystone correction are –30 to +30 degrees vertically,
and –30 to +30 degrees horizontally.
Adjusting the Volume Level (VOL +/–)
You can use the remote controller keys to adjust the volume level of the audio that is output
from the projector’s speaker.
To adjust the volume level
1. On the remote controller, press the [VOL +] or [VOL –] key.
z This causes the [Volume] screen to appear on the projected image.
2. Press the [VOL +] key or the [X] key to increase the volume, or the
[VOL –] or [W] key to lower the volume.
3. After the setting is the way you want, press the [ESC] key.
z This causes the [Volume] screen to disappear.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Projection Operations
Enlarging the Projected Image (D-ZOOM +/–)
You can use the remote controller’s zoom keys to enlarge a specific part of the projected
image up to four times its original size.
To enlarge part of the projected image
1. On the remote controller, press the [D-ZOOM +] or [D-ZOOM –] key.
z This causes a cross cursor to appear on the projected image.
2. Use the remote controller’s cursor keys to move the cross cursor to the
part of the image that you want in the center of the enlarged image.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Projection Operations
3. On the remote controller, press the [D-ZOOM +] key to enlarge the
image.
z You can press the [D-ZOOM +] key again to further enlarge the image, up to 4 times.
z You can back step through the image enlargements by pressing the [D-ZOOM –] key.
z
You can shift the zoomed image up, down, left, or right by pressing the applicable remote
controller cursor key
.
4. To exit image enlargement and return the image to its original size,
press the remote controller’s [ESC] key.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Projection Operations
Using Picture-in-Picture (P-IN-P)
While RGB is selected as the input source, you can display a sub-window that simultaneously
displays the image being input through the VIDEO or S-VIDEO terminal. This function is
called “picture-in-picture” or “P-IN-P”.
RGB input
image
VIDEO
(or S-VIDEO)
input image
z The initial default setting for the sub-window input source is VIDEO. Use the setup menu
when you want to change the sub-window input source to S-VIDEO. For details, see
“Input Settings J P-in-P Input” on page 90.
z Note that P-IN-P can be used only when RGB is selected as the input source. It is not
available while any other input source is selected.
z If Component is selected for “Input Settings J RGB Input” on the setup menu, you need
to change the setting to RGB in order to use picture-in-picture. Note that the initial
default setting for “Input Settings J RGB Input” is RGB.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Projection Operations
To display the sub-window
1. On the remote controller, press the [RGB] key to select RGB as the
input source.
z You can also select the input source using the projector’s [INPUT] key.
2. On the remote controller, press the [P-IN-P] key to display the sub-
window.
z This causes the sub-window, containing the image input through the VIDEO or S-VIDEO
terminal, to appear on the projected image. The sub-window will be located at the
position that was used the last time a sub-window was displayed. The initial default
location is the lower right corner.
z You can leave the sub-window where it is, or move it to another location within the
projected image. See “To change the location of the sub-window” for more information.
z You can also select one of three sizes for the sub-window. See “To change the size of
the sub-window” for more information.
3. To close the sub-window, press the remote controller’s [P-IN-P] key or
the [ESC] key.
To change the location of the sub-window
While a sub-window is displayed, use the remote controller’s cursor keys to move it to one of
the nine locations shown below.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Projection Operations
To change the size of the sub-window
While a sub-window is displayed, use the [D-ZOOM +] and [D-ZOOM –] keys to select one
of the three available sub-window sizes (small, medium, large).
[D-ZOOM +] key
Large
Medium
Small
[D-ZOOM –] key
z When RGB is selected as the input source, certain signal types (1600 × 1200 UXGA
signal, for example) do not support selection of the large sub-window size.
Muting the Image and Audio (MUTE)
The mute function causes the projected image to go to black screen, and stop output of the
audio from the speaker.
To mute the image and audio
1. On the remote controller, press the [MUTE] key.
z This causes the projected image to go to a black screen, and stops output from the
speaker.
2. To restore the image and audio, press the [MUTE] key again or press
the [ESC] key.
z You can select a black screen, blue screen, or a logo screen for the mute function. For
details, see “Screen Settings J Mute Screen” on page 88.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Projection Operations
Freezing the Projected Image (FREEZE)
The freeze function stores the current projected image in projector memory, and projects it as
a still image.
To freeze the projected image
1. On the remote controller, press the [FREEZE] key.
z This freezes the image that was being projected when you pressed the [FREEZE] key.
2. To unfreeze the image, press the [FREEZE] key again or press the
[ESC] key.
Operating the Computer with the
Remote Controller (Wireless Mouse)
You can use the remote controller as a wireless mouse to perform mouse operations on the
computer that is connected to the projector. Wireless mouse capabilities really come in handy
when you need to open a presentation software file for projection during a meeting or
presentation.
z To use the remote controller as a wireless mouse, the computer must be connected to
the projector by the USB cable that comes with the projector. For details, see
“Connecting a Computer to the Projector’s USB Port” on page 38.
z Note that wireless mouse capabilities are available only when RGB is selected as the
input source and there is RGB input from the computer to the projector.
To operate the computer with the remote controller
1. Use the mini D-Sub cable and USB cable that come with the projector
to connect the computer to the projector. After that, turn on the
projector and the computer.
z See the following for more information.
)Connecting a Computer to the Projector (Video and Audio) (page 37)
)Connecting a Computer to the Projector’s USB Port (page 38)
2. On the remote controller, press the [RGB] key to select RGB as the
input source.
z You can also select the input source using the projector’s [INPUT] key.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Projection Operations
3. Use the remote controller to perform mouse operations as described
below.
To do this:
Use this remote controller key:
Move the pointer on the computer screen
up, down, left, or right
Cursor key
Scroll up one page
Scroll down one page
Perform a left-click operation
Perform a right-click operation
[PAGE UP]
[PAGE DOWN]
[ENTER]
[ESC]
z Note that wireless mouse operations are not possible while a manual keystone correction
(page 55), volume adjustment (page 56), image enlargement (page 57), or P-IN-P (page 59)
operation is in progress, or while the menu is displayed (page 64). Wireless mouse
capabilities will be restored as soon as the operation that disabled them is complete.
z Note that wireless mouse operation is not supported when the input signal from the
computer is larger than XGA, and “Resize Image To Fit” (page 85) is turned off. Wireless
mouse operation will be supported for an input signal that is larger than XGA if “Resize
Image To Fit” is turned on.
z Note that drag-and-drop is not supported by wireless mouse operations.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Setup Menu
Using the Setup Menu
This section explains how to configure setup menu settings, and provides details about each
of the settings.
Setup Menu Overview
Pressing the [MENU] key while an image is being projected displays the setup menu on the
projected image. The setup menu can be used to configure a variety of different projector
settings. See the “Setup Menu Setting List” on page 65 for details about the settings that are
available.
Using the Setup Menu Setting List
z
The settings that can be configured and the settings that appear on the item depend on
the input source that is currently selected. Under “Input Source” in the following list, there
is a column for each of the input sources listed below. A “ ” in a column means that
the menu item to the left is displayed for that input source, while “ ” indicates that the
menu item is not displayed.
Column name:
Input source:
RGB
R
C
Component
S-VIDEO
S
V
VIDEO
No Signal
No signal being input
z
z
The “Sub-menu Item Type” column shows the type of the applicable sub-menu item. Refer
to the pages noted below for more information about each item type.
Value Setting: Specifies a numeric value () page 70).
Selection:
Allows selection from multiple options () page 71).
Setting Screen:Numeric value specification or option selection on a separate setting screen
() page 71).
Execution:
Initializes a setting () page 74).
Information:
Displays information only () page 73).
The “See page” column shows where you should go for more information.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Setup Menu
Setup Menu Setting List
Input source
Sub-menu
Item Type
Main menu
Sub-menu
See page
R
C
S
V
No Signal
Brightness
Contrast
Sharpness
Value Setting
Value Setting
Value Setting
Value Setting
Value Setting
Setting Screen
Setting Screen
Value Setting
Value Setting
Value Setting
Value Setting
Selection
page 77
page 77
page 77
page 77
page 77
page 78
page 78
page 80
page 80
page 81
page 81
page 81
page 82
page 82
page 82
Saturation
Tint
*2 *2
Gamma Mode
Color Balance
Vertical Position
Horizontal Position
Frequency
Image
Adjustment
Phase
Noise Filter
Restore Menu Defaults
Volume
Restore Menu Defaults
Vertical Keystone
Correction
Execution
Value Setting
Execution
*1
Volume
Adjustment
Value Setting
Value Setting
page 83
page 83
Horizontal Keystone
Correction
Aspect Ratio
Selection
Selection
Selection
Selection
Selection
*3
page 84
page 85
page 86
page 86
page 87
page 87
page 88
page 88
page 89
page 89
page 89
page 90
page 91
page 91
page 92
Resize Image To Fit
Projection Mode
Ceiling Mount
Startup Screen
No Signal Screen
Mute Screen
Screen
Settings
Selection
Selection
Restore Menu Defaults
RGB Input
Execution
Selection
Setting Screen
Setting Screen
Selection
Selection
Setting Screen
Execution
*4
*5
*6
*7
Video Signal
S-Video Signal
P-in-P Input
Input
Settings
Signal Name Indicator
Special Signal
Restore Menu Defaults
*7
*1 This setting is for the currently selected input source.
*2 This setting can be configured only for an NTSC or NTSC4.43 signal.
*3 This setting can be selected only when the aspect ratio of the input signal is 4:3.
*4 This setting can be configured only when the input source is RGB/Component.
*5 This setting can be configured only when the input source is VIDEO.
*6 This setting can be configured only when the input source is S-VIDEO.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Setup Menu
Setup Menu Setting List
Input source
Sub-menu
Item Type
Main menu
Sub-menu
See page
R
C
S
V
No Signal
Auto Input Detect
Auto Adjust
Low-noise Mode
Auto Power Off
Key Lock
Power On Password
Custom Logo Settings
Language
Selection
Selection
Selection
Selection
Selection
page 92
page 93
page 93
page 94
page 94
page 95
page 99
page 105
page 105
page 106
page 106
*8
Option
Settings1
Special*7
Special*9
Setting Screen
Selection
Execution
Selection
Alert Tones
Restore Menu Defaults
AF/AK Mode
Power On AF/AK
Mode
Zoom Memory
Restore Menu Default
Lamp Time
Reset Lamp Time
Input Signal
Signal Name
Index
Resolution
Horizontal Frequency
Vertical Frequency
Scan System
Selection
page 107
Option
Settings2
Selection
Execution
Information
Execution
Information
Information
Information
Information
Information
Information
Information
page 108
page 108
page 109
page 109
page 109
page 109
page 109
page 109
page 109
page 109
page 109
Operational
Info
Restore All
Defaults
Restore All Defaults
Execution
page 110
*7 This is a special sub-menu item that is different from other types. For details, see “Option
Settings1 J Power On Password” on page 95.
*8 This setting can be configured only when the input source is RGB.
*9 This is a special sub-menu item that is different from other types. For details, see “Option
Settings1 J Custom Logo Settings” on page 99.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Setup Menu
Before Configuring Menu Settings
Always remember that the settings you configure on the setup menu are applied for the input
source (RGB, Component, S-VIDEO, VIDEO) that was selected when you displayed the setup
menu. Note the following important points.
z
The items that appear on the setup menu depend on the currently selected input source
and other factors.
Some items apply to a certain specific input source, while some apply to multiple input
sources.
z
z
Even for menu items that are common to multiple input sources, the setting range or
selectable options may differ according to the input source.
With certain exceptions, there are basically two types of settings that can be configured
for multiple input sources. One type lets you configure different settings for each individual
input source. The other type applies a single setting to all input sources. The volume
level setting, for example, lets you configure a different setting for each input source, while
the keystone correction setting lets you configure a single common setting for all input
sources.
z For details about how settings are saved, and other details, see “Setup Menu Reference”
on page 77.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Setup Menu
Setup Menu Screen Operations
This section explains projector operations you need to perform while configuring setup menu
settings. It also provides details about each sub-menu item type.
Basic Setup Menu Operations
The following is the general flow of the steps you need to perform when configuring setup
menu operations.
1. Select the input source whose settings you want to configure.
2. Press the [MENU] key.
z This causes the setup menu screen to appear in the center of the projected image.
z The setup menu has a main menu on the left side. On the right side is a sub-menu of
settings that can be configured for the currently selected main menu item.
Main menu
Sub-menu
z The items that appear in the sub-menu depend on the currently selected input source,
and whether or not a signal is being input from the input source. For details, see
“Setup Menu Overview” on page 64.
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Setup Menu
3. Use the [S] and [T] keys to select the main menu whose sub-menu
contains the settings you want to configure.
z The settings for the selected main menu item appear in the sub-menu.
4. Press the [ENTER] key.
z This selects the top item in the sub-menu.
5. Use the [S] and [T] keys to select the sub-menu item whose setting
you want to change.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Setup Menu
6. Change the setting or select an option to configure the currently
selected sub-menu item.
z The operation you need to perform depends on the sub-menu item type. See “Setup
Menu Overview” on page 64 for more information.
z For information about how to configure settings for each sub-menu item, see “Sub-menu
Operations” on page 70.
z After configuring the settings of one sub-menu item, you can repeat steps 5 and 6 to
select another item on the same sub-menu and configure its setting.
z If you want to configure the settings of another main menu item, press the [ESC] key
to exit the current sub-menu. Next, repeat steps 3 through 6 to select another main
menu item and change the settings of its sub-menu.
7. Press the [MENU] key to exit the setup menu.
z This causes the setup menu to disappear from the projected image.
Sub-menu Operations
This section explains steps you need to perform in order to configure settings for each sub-
menu item type (value, selection, setting screen, execution, information).
Value Setting Type Sub-menu Item
This type of sub-menu item consists of a value and a bar graph.
Examples:
Image Adjustment J Brightness; Screen Settings J Vertical Keystone
Correction
Operation:
Press the [W] key to make the value smaller, or the [X] key to make it
larger. A value can be selected within the range that the indicator is able
to move within the selected bar. Depending on conditions, the indicator may
not move all the way to either end of the bar.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Setup Menu
Selection Type Sub-menu Item
This type of sub-menu item provides a number of options from which you can choose.
Example :
Operation:
Screen Settings J Startup Screen
The currently selected option is indicated by a black button next to it. Use
the [W] and [X] keys to move between the selections, which causes the
buttons next to them to become either black (selected) or white
(deselected).
z For details about the options that are available for each selection type sub-menu item,
see “Setup Menu Reference” on page 77.
Setting Screen Type Sub-menu Item
This type of sub-menu item displays a separate screen that you use to configure its settings.
Examples:
Operation:
Image Adjustment J Gamma Mode; Option Settings1 J Language, etc.
The following example shows how to configure settings for Input Settings J
Video Signal, S-Video Signal
1. Press the [VIDEO] key to select the VIDEO input terminal as the input
source.
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Setup Menu
2. Perform steps 2 through 4 under “Basic Setup Menu Operations” on
page 68. On the “Input Settings” main menu, select the “Video Signal”
sub-menu item.
3. Press the [ENTER] key.
z This displays the video signal selection screen shown below.
4. Use the [S] and [T] keys to highlight the item you want to select, and
then press the [ENTER] key.
5. After you are finished configuring the settings, press the [ESC] key to
close the setting screen and return to the sub-menu screen.
z After you are finished, press the [MENU] key to exit the setup menu.
z Note that the available settings and configuration procedures depend on the setting
screen. See “Setup Menu Reference” on page 77 for details about each sub-menu item.
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Setup Menu
Execution Type Sub-menu Item
This type of sub-menu item returns a setting to its initial default value.
Examples:
Image Adjustment J Restore Menu Defaults; Operational Info J Reset
Lamp Time
)Initializing Settings (page 74)
)Resetting the Lamp Time (page 117)
Information Type Sub-menu Item
This type of sub-menu item provides status and setup information.
Example:
Operational Info J Lamp Time; Operational Info J Input Signal
Refer to the following for details about the type of information that is available using the
information type sub-menu items.
)Operational Info (page 109)
)Operational Info J Input Signal (page 109)
)Operational Info J Signal Name (page 109)
)Operational Info J Index (page 109)
)Operational Info J Resolution (page 109)
)Operational Info J Horizontal Frequency (page 109)
)Operational Info J Vertical Frequency (page 109)
)Operational Info J Scan System (page 109)
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Setup Menu
Initializing Settings
The setup menu lets you initialize the settings of a particular main menu item, or for all
setup menu items.
To initialize the settings of a particular main menu item
Example: To initialize the settings of the “Image Adjustment” main menu item.
z Performing the following procedure returns all of the sub-menu items under the currently
selected main menu item to their initial default settings.
z Initializing the settings of the “Image Adjustment” main menu item returns the “Vertical
Position”, “Horizontal Position”, “Frequency”, and “Phase” settings of the current signal
type only (XGA/60Hz, UXGA/60Hz, etc.) to their initial defaults.
1. Select the input source whose settings you want to initialize.
2. Perform steps 2 through 4 under “Basic Setup Menu Operations” on
page 68. Select the “Image Adjustment” main menu, and then select
the “Restore Menu Defaults” sub-menu item.
74
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Setup Menu
3. Press the [ENTER] key.
z This displays a confirmation message asking if you want to initialize settings.
4. Use the [S] and [T] keys to select [Yes].
5. Press the [ENTER] key to initialize the menu’s settings, or the [ESC]
key to exit the initialize operation without doing anything.
z Pressing the [ENTER] key returns all of the sub-menu items on the currently selected
main menu to their initial default settings.
To initialize all menu settings
z Performing the following procedure initializes all sub-menu items for all menus, except for
the language (Option Settings1 J Language) and the lamp time (Operational Info J
Lamp Time).
z Note that initialization does not delete the custom logo.
1. Perform steps 1 through 4 under “Basic Setup Menu Operations” on
page 68. Select the “Restore All Defaults” main menu, and then select
the “Restore All Defaults” sub-menu item.
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Setup Menu
2. Press the [ENTER] key.
z This displays a confirmation message asking if you want to initialize all settings.
3. Use the [S] and [T] keys to select [Yes].
4. Press the [ENTER] key to initialize all menu settings, or the [ESC] key
to exit the initialize operation without doing anything.
z Pressing the [ENTER] key initializes all menu items except for “Language” and “Lamp
Time”.
76
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Setup Menu
Setup Menu Reference
This section provides detailed explanations about the contents for all of the setup menu items.
z The titles in this section use the format: Main Menu Item
Sub-menu Item.
J
Image Adjustment
IImage Adjustment
Brightness
J
This sub-menu adjusts the brightness of the projected image. A larger value produces a
brighter image.
z
z
This setting is not possible when there is no input signal.
A different setting can be configured and is stored for each input source.
IImage Adjustment
Contrast
J
This sub-menu adjusts the contrast of the projected image. A larger value produces a
stronger contrast.
z
This setting is not possible when there is no input signal.
z
A different setting can be configured and is stored for each input source.
IImage Adjustment
Sharpness
J
This sub-menu adjusts the sharpness of the projected image. A larger value makes the image
sharper, while a smaller value makes it softer.
z
This setting is not possible when there is no input signal.
z
A different setting can be configured and is stored for each input source.
IImage Adjustment
Saturation
J
This sub-menu adjusts the color saturation of the projected image. A larger value increase
color saturation.
z
This setting is not possible when the input source is RGB/Component and when there is
no input signal.
z
A different setting can be configured and is stored for each input source.
IImage Adjustment
Tint
J
This sub-menu adjusts the tint of the projected image. A larger value makes the overall
image more reddish, while a smaller value makes the overall image more bluish.
z
This setting is not possible when the input source is RGB/Component and when there is
no input signal.
z
A different setting can be configured and is stored for each input source.
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Setup Menu
IImage Adjustment Gamma Mode
J
This sub-menu lets you select the gamma mode for the projected image.
Input Source Specific Menu Items
Input Source
RGB
Available Items (Parentheses indicate defaults.)
Standard, (Presentation), Theater, Graphics/Blackboard
Standard, Presentation, (Theater), Graphics/Blackboard
Component
S-VIDEO
VIDEO
No Signal
None
Setting Explanations
Standard:
Standard gamma mode
Presentation: Emphasis on clarity to make text easy to read
Theater:
Emphasis on reproduction of moderate color tones and dark image areas
Emphasis on color gradations and contrast
Graphics:
Blackboard: Optimizes color correction for projection onto a blackboard.
Setting Storage
A different setting is stored for each input source.
IImage Adjustment
Color Balance
J
This sub-menu lets you adjust the color balance of the projected image. There are two
methods you can use to adjust color balance, selecting a preset color temperature value or
adjusting the red, green, or blue components of each color.
z
Note that you can adjust the color balance either by selecting a color temperature value
or by adjusting color components. You cannot do both.
z
z
Color balance settings cannot be configured when there is no input signal.
A different setting can be configured and is stored for each input source.
Adjusting Color Balance by Selecting a Color Temperature Value
You can use the procedure below to adjust color balance by selecting one of three color
temperatures (low, normal, high).
Changing the color temperature of an image alters its whiteness. A lower color temperature
makes whites redder, while a higher color temperature makes them bluer.
1. On the “Image Adjustment” main menu, select the “Color Balance” sub-
menu item, and then press the [ENTER] key.
z This displays the color balance setting screen.
78
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Setup Menu
2. Use the [S] and [T] keys to select “Color Temperature”, and then
press the [ENTER] key.
z This causes a
marker to appear at the beginning of the “Color Temperature” line,
z
which indicates that color temperature value selection is enabled.
3. Use the [W] and [X] keys to select the color temperature setting you want.
4. After the setting is the way you want, press the [MENU] key.
Adjusting Color Balance by Adjusting Color Components
Instead of specifying a color temperature to adjust color balance, you can also individually
adjust the relative intensity of the red, green, and blue components.
1. On the “Image Adjustment” main menu, select the “Color Balance” sub-
menu item, and then press the [ENTER] key.
z This displays the color balance setting screen.
2. Use the [S] and [T] keys to select “Color”, and then press the
[ENTER] key.
z This causes a
marker to appear at the beginning of the “Color” line, which indicates
z
that color adjustment is enabled.
3. Use the [S] and [T] keys to select the color you want to adjust, and
then use the [W] and [X] keys to adjust it.
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Setup Menu
4. After all the settings are the way you want, press the [MENU] key.
IImage Adjustment
Vertical Position
J
This sub-menu lets you adjust the vertical position of the input source image within the
projection area.
z
z
This setting is not possible when there is no input signal.
“Image Adjustment” main menu item settings are saved for the current signal type only
(XGA/60Hz, UXGA/60Hz, etc.), and not for the input signal source. Note, however, that the
number of signal type settings that can be saved is limited. Exceeding the limit causes
the oldest setting to be deleted automatically.
IImage Adjustment
Horizontal Position
J
This sub-menu lets you adjust the horizontal position of the input source image within the
projection area.
z
z
This setting is not possible when there is no input signal.
See “Image Adjustment J Vertical Position” for details about how settings are saved.
80
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Setup Menu
IImage Adjustment Frequency
J
This sub-menu lets you manually control the frequency of the image.
Normally, the projector is able to adjust the frequency automatically. If there are vertical bands
in the projected image, however, it means that automatic adjustment is not possible for some
reason. When this happens use this setting to adjust the image frequency.
z
z
This setting is possible only when RGB is selected as the input source.
Settings are saved for each signal type (XGA/60Hz, UXGA/60Hz, etc.). Note, however, that
the number of signal type settings that can be saved is limited. Exceeding the limit
causes the oldest setting to be deleted automatically.
z If, for some reason, your manual frequency settings cause the image input from the
computer to disappear from the projection, you can press the [AUTO] key to perform an
auto adjust operation (page 51), which should cause the image to reappear.
IImage Adjustment
Phase
J
This sub-menu lets you manually control the phase of the image.
Normally, the projector is able to adjust the phase automatically. If there are color errors or
flickering in the projected image, however, it means that automatic adjustment is not possible
for some reason. When this happens use this setting to adjust the image phase.
z
This setting is possible only when RGB is selected as the input source.
z
See “Image Adjustment J Frequency” for details about how settings are saved.
IImage Adjustment
Noise Filter
J
This sub-menu provides a choice of noise filter levels to remove digital noise from the
projected image when RGB is selected as the input source. Note that the noise filter may not
be able to remove certain types of digital noise.
z
This setting is possible only when RGB is selected as the input source. The setting is
saved for the RGB input source only.
z
Turning off the projector automatically returns this sub-menu to its initial default setting
(Normal).
Input Source Specific Menu Items
Input Source
RGB
Available Items (Parentheses indicate defaults.)
Low, (Normal), High
None
Component
S-VIDEO
VIDEO
No Signal
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Setup Menu
IImage Adjustment Restore Menu Defaults
J
This sub-menu returns all of the sub-menu items on the Image Adjustment main menu to
their initial default settings.
z
You can perform initialization even when there is no input signal. In this case, the
initialization is performed for the currently selected input source.
“Image Adjustment” main menu “Vertical Position”, “Horizontal Position”, “Frequency”, and
“Phase” settings are initialized for the current signal type (XGA/60Hz, UXGA/60Hz, etc.)
only.
z
z
For details about the initialization procedure, see “To initialize the settings of a particular
main menu item” on page 74.
Volume Adjustment
IVolume Adjustment
Volume
J
This sub-menu can be used to adjust the volume level of the projector’s speaker. This setting
is also linked to volume settings made with the remote controller’s [VOL +] and [VOL –] keys.
z
Changing this setting when there is no input signal changes the volume setting of the
currently selected signal source.
z
A different setting is stored for each input source.
IVolume Adjustment
Restore Menu Defaults
J
This sub-menu returns Volume to its initial default setting.
z
You can perform initialization even when there is no input signal. In this case, the
initialization is performed for the currently selected input source.
Initialization is performed separately for each input source.
For details about the initialization procedure, see “To initialize the settings of a particular
main menu item” on page 74.
z
z
82
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Setup Menu
Screen Settings
IScreen Settings
Vertical Keystone Correction
J
This sub-menu lets you correct for vertical keystoning of the projected image.
z
z
Vertical keystone correction can be performed regardless of the currently selected input
source.
A single setting is stored, which is applied to all input sources.
IScreen Settings
Horizontal Keystone Correction
J
This sub-menu lets you correct for horizontal keystoning of the projected image.
z
z
Horizontal keystone correction can be performed regardless of the currently selected input
source.
A single setting is stored, which is applied to all input sources.
83
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Setup Menu
IScreen Settings Aspect Ratio
J
This sub-menu lets you select the aspect ratio (ratio between the vertical and horizontal
dimensions) of the projected image.
Input Source Specific Menu Items
Input Source
RGB
Available Items (Parentheses indicate defaults.)
None
Component
S-VIDEO
VIDEO
(4:3), 16:9
No Signal
None
Setting Explanations
4:3: Sets the aspect ratio of the projected image to 4:3 (same as a standard TV
screen). This setting is normally used when S-VIDEO or VIDEO is selected as
the input source.
16:9: Sets the aspect ratio of the projected image to 16:9 (same as a movie screen
or high-definition TV screen). Using this setting when the input source image is
a 16:9 image that has been squeezed to a 4:3 image causes the image to be
projected with its normal 16:9 aspect ratio.
Setting Storage
A different setting is stored for each input source.
z When a component signal with an aspect ratio of 16:9 is sent from the input source, the
aspect ratio of the projected image is automatically switched to 16:9. In this case, this
setting cannot be changed.
z Using this projector to reduce, enlarge, or otherwise alter an image for business purposes
or public display may infringe upon the rights of the individual who holds the copyright of
the image.
84
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Setup Menu
IScreen Settings Resize Image to Fit
J
When RGB is selected as the input source and the video resolution of the connected
×
computer is anything other than XGA (1024 768 pixels), “Resize Image To Fit” automatically
enlarges or reduces the input image so it matches the video resolution of the projector and
fills the entire screen.
Input Source Specific Menu Items
Input Source
RGB
Available Items (Parentheses indicate defaults.)
(On), Off
None
Component
S-VIDEO
VIDEO
No Signal
Setting Explanations
On: When the input signal from the computer connected to the projector is not an
XGA signal, the image is automatically enlarged or reduced so it matches the
projector’s video resolution and fills the entire screen.
Off: Turns off resizing of the image input from the computer. If the image input from
the computer is smaller than XGA, the size of the projected image will also be
smaller. When the image input from the computer is larger than XGA, only the
center part of the image that corresponds to XGA size is projected.
z Resizing of an input image by “Resize Image To Fit” can call coarsening of the image or
can cause part of the image to be cut off. If this happens, try turning off “Resize Image
To Fit”. Note, however, that turning off “Resize Image To Fit” can cause the projected
image to become smaller, or it can cause only the center part of the image to be
projected.
Setting Storage
This setting is possible only when RGB is selected as the input source. The setting is
saved for the RGB input source only.
85
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Setup Menu
IScreen Settings Projection Mode
J
Use this sub-menu to specify whether projection will be from the front of the screen or the
back of the screen.
Input Source Specific Menu Items
Input Source
RGB
Available Items (Parentheses indicate defaults.)
(Front), Rear
Component
S-VIDEO
VIDEO
No Signal
Setting Explanations
Front: For projection from the front of the screen.
Rear: For projection from the back of the screen. This setting flips the front projected
image horizontally.
Setting Storage
A single setting is stored, which is applied to all input sources.
IScreen Settings
Ceiling Mount
J
Use this sub-menu to configure the projector for use in an installation in which it is positioned
upside down.
Input Source Specific Menu Items
Input Source
RGB
Available Items (Parentheses indicate defaults.)
On, (Off)
Component
S-VIDEO
VIDEO
No Signal
Setting Explanations
On: Flips the projected image horizontally and vertically.
Off: Projects a normal image.
Setting Storage
A single setting is stored, which is applied to all input sources.
86
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Setup Menu
IScreen Settings Startup Screen
J
Use this sub-menu to specify whether or not a startup screen should be projected whenever
the projector is turned on.
Input Source Specific Menu Items
Input Source
RGB
Available Items (Parentheses indicate defaults.)
(Logo), None
Component
S-VIDEO
VIDEO
No Signal
Setting Explanations
Logo: Projects the logo screen as the startup screen.
A built-in logo screen is the initial default startup screen. You can also create a
custom logo, if you want. For details, see “Option Settings1 J Custom Logo
Settings” on page 99.
None: No startup screen is projected.
Setting Storage
A single setting is stored, which is applied to all input sources.
IScreen Settings
No Signal Screen
J
This sub-menu lets you specify what should be projected when there is no input signal to the
projector.
Input Source Specific Menu Items
Input Source
RGB
Available Items (Parentheses indicate defaults.)
(Blue), Black, Logo
Component
S-VIDEO
VIDEO
No Signal
Setting Explanations
Blue: Displays a blue screen when there is no input signal.
Black: Displays a black screen when there is no input signal.
Logo: Displays a logo screen when there is no input signal.
A built-in logo screen is the initial default startup screen. You can also create a
custom logo, if you want. For details, see “Option Settings1 J Custom Logo
Settings” on page 99.
87
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Setup Menu
Setting Storage
A single setting is stored, which is applied to all input sources.
IScreen Settings
Mute Screen
J
This sub-menu lets you specify what should be projected during mute (page 61).
Input Source Specific Menu Items
Input Source
RGB
Available Items (Parentheses indicate defaults.)
Blue, (Black), Logo
Component
S-VIDEO
VIDEO
No Signal
Setting Explanations
Blue: Displays a blue screen during mute.
Black: Displays a black screen during mute.
Logo: Displays a logo screen during mute.
A built-in logo screen is the initial default startup screen. You can also create a
custom logo, if you want. For details, see “Option Settings1 J Custom Logo
Settings” on page 99.
Setting Storage
A single setting is stored, which is applied to all input sources.
IScreen Settings
Restore Menu Defaults
J
This sub-menu returns all of the sub-menu items on the Screen settings main menu to their
initial default settings.
z
You can perform initialization even when there is no input signal. In this case, the
initialization is performed for the currently selected input source.
Basically, initialization initializes the settings of the current input source. Note, however, that
the following settings are always initialized, regardless of the currently selected input
source.
z
Vertical keystone correction
Horizontal keystone correction
Projection Mode
Ceiling Mount
Startup screen
No signal screen
Mute screen
z
For details about the initialization procedure, see “To initialize the settings of a particular
main menu item” on page 74.
88
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Setup Menu
Input Settings
IInput Settings
RGB Input
J
This sub-menu lets you specify the type of input signal in accordance with the device
connected to the projector’s RGB terminal.
Input Source Specific Menu Items
Input Source
RGB
Available Items (Parentheses indicate defaults.)
(RGB), Component
Component
S-VIDEO
VIDEO
None
No Signal
(RGB), Component
* Only when the currently selected input source is RGB or
Component.
Setting Explanations
RGB:
Select this setting when a computer is connected to the projector’s RGB
input terminal. For details about connection, see “Connecting a Computer
to the Projector (Video and Audio)” on page 37.
Component: Select this setting when the projector’s RGB input terminal is connected
the component video output terminal of a video device using an optionally
available YK-3 component video cable. For details about connection, see
“Connecting to a Component Video Output Device” on page 40.
Setting Storage
This setting is saved for the RGB input terminal only.
IInput Settings
Video Signal, S-Video Signal
J
This sub-menu specifies the input signal for the projector’s VIDEO and S-VIDEO input
terminals.
Input Source Specific Menu Items
Input Source
RGB
Available Items (Parentheses indicate defaults.)
None
Component
S-VIDEO
VIDEO
(Auto), NTSC, NTSC4.43, PAL, PAL-M, PAL-N, PAL60, SECAM
No Signal
(Auto), NTSC, NTSC4.43, PAL, PAL-M, PAL-N, PAL60, SECAM
* Only when the currently selected input source is VIDEO or
S-VIDEO.
89
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Setup Menu
Setting Explanations
Auto:
Select this setting to have the projector switch the video signal system
automatically in accordance with the input signal from the video device
that is connected to the VIDEO or S-VIDEO input terminal. This is the
setting you should normally use.
Other settings: Each setting selects the applicable video system. Use these settings
when you want to specify only one specific video signal for the VIDEO
and S-VIDEO input terminal.
Setting Storage
This setting is saved for the VIDEO and S-VIDEO input terminal only.
IInput Settings
P-in-P Input
J
This sub-menu lets you select the input source for the image that appears in the P-in-P sub-
window (page 59).
Input Source Specific Menu Items
Input Source
RGB
Available Items (Parentheses indicate defaults.)
(VIDEO), S-VIDEO
None
Component
S-VIDEO
VIDEO
No Signal
(VIDEO), S-VIDEO
* Only when the currently selected input source is RGB.
Setting Explanations
VIDEO: Select VIDEO as the input source of the sub-window.
S-VIDEO: Select S-VIDEO as the input source of the sub-window.
Setting Storage
This setting is saved for the RGB input terminal only.
90
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Setup Menu
IInput Settings Signal Name Indicator
J
This sub-menu lets you specify whether or not the name of the currently selected input
source should be displayed in the projected image.
Input Source Specific Menu Items
Input Source
RGB
Available Items (Parentheses indicate defaults.)
(On), Off
Component
S-VIDEO
VIDEO
No Signal
Setting Explanations
On: Turns on display of the name of the currently selected input source in the
projected image.
Off: Turns off display of the input source name.
Setting Storage
A single setting is stored, which is applied to all input sources.
IInput Settings
Special Signal
J
When a computer is connected to the RGB input terminal, the projector automatically detects
the type of RGB signal being sent from the computer and projects the image. Some signals,
however, cannot be detected properly by the projector. When auto detection is not possible for
×
some reason, try using this setting for a computer signal with a resolution of SXGA (1280
×
1024) or SXGA+ (1400 1050).
Input Source Specific Menu Items
Input Source
RGB
Available Items (Parentheses indicate defaults.)
×
×
1280 1024, (1400 1050)
Component
S-VIDEO
VIDEO
None
No Signal
* Only when the currently selected input source is RGB.
Setting Explanations
×
×
1280 1024:Specifies an SXGA (1280 1024) resolution RGB signal.
×
×
1400 1050:Specifies an SXGA+ (1400 1050) resolution RGB signal.
Setting Storage
This setting is saved for the RGB input terminal only.
91
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Setup Menu
IInput Settings Restore Menu Defaults
J
This sub-menu returns all of the sub-menu items on the Input Settings main menu to their
initial default settings.
z
You can perform initialization even when there is no input signal. In this case, the
initialization is performed for the currently selected input source.
Basically, initialization initializes the settings of the current input source. Note, however, that
the signal name indicator setting is always initialized, regardless of the currently selected
input source.
z
z
For details about the initialization procedure, see “To initialize the settings of a particular
main menu item” on page 74.
Option Settings1
IOption Settings1
Auto Input Detect
J
This sub-menu lets you specify whether auto detect of the input source should be performed
whenever the projector is turned on (page 47).
Input Source Specific Menu Items
Input Source
RGB
Available Items (Parentheses indicate defaults.)
(On), Off
Component
S-VIDEO
VIDEO
No Signal
Setting Explanations
On: Turns on auto detection of the input source whenever the projector is turned on.
Off: Turns off auto detection of the input source whenever the projector is turned on.
Setting Storage
A single setting is stored, which is applied to all input sources.
92
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Setup Menu
IOption Settings1 Auto Adjust
J
This sub-menu lets you specify whether or not auto adjustment should be performed (page
51) when RGB is selected as the input source.
Input Source Specific Menu Items
Input Source
RGB
Available Items (Parentheses indicate defaults.)
(On), Off
None
Component
S-VIDEO
VIDEO
No Signal
(On), Off
* Only when the currently selected input source is RGB.
Setting Explanations
On: Turns on auto adjustment, which is performed when RGB is selected as the input
source.
Off: Turns off auto adjustment.
Setting Storage
This setting is saved for the RGB input terminal only.
IOption Settings1
Low-noise Mode
J
The low-noise mode reduces the luminosity of the projection lamp and the speed of the
cooling fan, allowing quieter projector operation.
Input Source Specific Menu Items
Input Source
RGB
Available Items (Parentheses indicate defaults.)
On, (Off)
Component
S-VIDEO
VIDEO
No Signal
Setting Explanations
On (low-noise mode): This mode reduces luminosity and fan motor speed for quieter
operation than the normal mode.
Off (normal mode):
This mode projects at normal luminosity.
Setting Storage
A single setting is stored, which is applied to all input sources.
93
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Setup Menu
IOption Settings1 Auto Power Off
J
This sub-menu lets you turn Auto Power Off (page 45) on or off.
Input Source Specific Menu Items
Input Source
RGB
Available Items (Parentheses indicate defaults.)
(On), Off
Component
S-VIDEO
VIDEO
No Signal
Setting Explanations
On: Turns on Auto Power Off.
Off: Turns off Auto Power Off.
Setting Storage
A single setting is stored, which is applied to all input sources.
IOption Settings1
Key Lock
J
This sub-menu lets you turn key lock on and off.
Input Source Specific Menu Items
Input Source
RGB
Available Items (Parentheses indicate defaults.)
On, (Off)
Component
S-VIDEO
VIDEO
No Signal
Setting Explanations
On: Turns on key lock and disables projector keys.
Off: Turns off key lock and enables projector keys.
Setting Storage
A single setting is stored, which is applied to all input sources.
94
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Setup Menu
z Besides the menu operation explained above, the following operations can also be used
to turn off key lock.
zWhile the projector is on: Hold down the projector’s [ESC] key for about five seconds.
zWhile the projector is off: Simultaneously hold down the projector’s [ESC] and [
(power) keys for about five seconds. This turns on the
projector and also turns off key lock.
]
z You can use the above projector operations to turn off key lock if the remote controller
batteries unexpectedly go dead, etc.
IOption Settings1 J Power On Password
This sub-menu lets you turn the power on password on and off.
While the password is turned on, projector operation is impossible unless the correct password
is entered.
Initial Factory Default Password
The following is the 8-key operation you should perform to input the initial factory default
password.
[AF/AK], [PAGUP], [PAGEDOWN], [S], [T], [W], [X], [MENU]
z Note that the projector’s password is not really a “word”, but rather a series of remote
controller key operations.
z If you need to keep projector operation secure, be sure to change the initial factory
default password to a different one as soon as possible.
z The password can be input using the remote controller only. Optimum security is ensured
by turning on the password and keeping the remote controller with you.
z If you forget your password, contact your original dealer or authorized CASIO Service
Center. There, your projector will be initialized to its initial factory default settings. In
addition to the password, all other projector settings (except for the lamp time) will be
returned to their initial factory defaults.
95
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Setup Menu
Input Source Specific Menu Items
Input Source
RGB
Available Items (Parentheses indicate defaults.)
On, (Off)
Component
S-VIDEO
VIDEO
No Signal
Setting Explanation
On: Turns on the power on password, which requires input of a password to turn on
the projector.
Off: Turns off the password, which allows the projector to be operated without
inputting a password.
Setting Storage
A single setting is stored, which is applied to all input sources.
Using the Password Input Dialog Box
The password input dialog box will appear when any one of the following occurs. The text
inside the dialog box depends on the type of operation you are performing.
z
z
z
When you turn on the projector while the password is turned on
When you turn the password on or off
When you change the password
When this dialog box is shown, perform a remote controller key operation for each of the
password input positions. The following explains how to input numbers.
z
When the password input dialog box first appears, all of its input positions are blank,
and the cursor is flashing at the first (leftmost) input position.
The cursor is used to select an input position for input.
You can perform any one of the 20 remote controller key operations shown below
when inputting a password.
z
z
[AF/AK], [PAGEUP], [PAGEDOWN], [MENU], [KEYSTONE], [D-ZOOM +], [D-ZOOM –],
[RGB], [VIDEO], [S-VIDEO], [AUTO], [P-IN-P], [MUTE], [FREEZE], [VOL +], [VOL –],
[S], [T], [W], [X]
z
Each time you perform a remote controller key operation, “„” appears at the current
input position, and the cursor moves to the next input position to the right.
A password can be from one to eight key operations long.
z
z
After performing all of the key operations you want, press the [ENTER] key.
96
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Setup Menu
To display the power on password setting screen
1. Perform steps 1 through 4 under “Basic Setup Menu Operations” on
page 68. Select the “Option Settings1” main menu, and then select
the “Power On Password” sub-menu item.
2. Press the [ENTER] key.
z This displays a password input dialog box like the one shown below.
3. Input the current password.
z For information about how to input the password, see “Using the Password Input
Dialog Box”.
4. Press the [ENTER] key.
z If the password you input does not match the currently registered password, the
message “The password you input is wrong”. appears. Press the [ESC] key to
return to step 1.
z If the password you input matches the registered password, pressing [ENTER] above
displays the power on password setting screen.
To turn the power on password on and off
1. Display the power on password setting screen.
z See “To display the power on password setting screen” on page 97.
97
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Setup Menu
2. Use the [S] and [T] keys to select “Power On Password”, if you
want.
3. Use the [W] and [X] keys to turn the power on password on or off.
z Changing the power on password setting causes the message like the one shown
below to appear.
z Press the [ENTER] key to change the setting. If you do not want to change the
setting, press the [ESC] key.
To change the power on password
1. Display the power on password setting screen.
z See “To display the power on password setting screen” on page 97.
2. Use the [S] and [T] keys to select “Change Password”.
3. Press the [ENTER] key.
z This displays the new password input dialog.
98
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Setup Menu
4. Input the new password, and then press the [ENTER] key.
z This displays a dialog box for re-inputting the password for confirmation.
5. Re-input the same password you input in step 4, and then press
[ENTER].
z If the two passwords you input were identical, the message “Your new password has
been registered.” appears. Press the [ESC] key.
z If the password you input here is different from the one you input in step 4 the
message “The two passwords you input are different.” appears. Press the [ESC] key
to return to step 1.
IOption Settings1
Custom Logo Settings
J
With this sub-menu, you can cut part of the projected screen and use it to create an original
logo, which you can display for the startup screen, the no signal screen, and the mute
screen. An original logo that you create is called a “custom logo”. The custom logo settings
let you create a custom logo, view your custom logo, and perform other operations.
z
z
Custom logo settings cannot be configured when there is no input signal.
A single custom logo is stored, which is applied to all input sources.
Capturing a Custom Logo Image
You can create a custom logo by capturing part of an image that is currently being
projected by the projector.
z The display size and position of a custom logo created by capturing an image depend on
the configuration of the following settings when you capture the image: Logo Vertical, Logo
Horizontal, Custom Logo Zoom, Background Color, and Resolution. Make sure that you
configure these settings the way you want before performing the image capture operation.
For details of these operations, see “Configuring Custom Logo Capture Settings” on page
102.
99
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Setup Menu
To capture a custom logo
1. Project the still image that you want to use as the custom logo.
2. Perform steps 1 through 4 under “Basic Setup Menu Operations” on
page 68. Select the “Option Settings1” main menu, and then select
the “Custom Logo Settings” sub-menu item.
3. Press the [ENTER] key.
z This displays the custom logo settings screen.
4. Use the [S] and [T] keys to select “Start Capture”, and then press
the [ENTER] key.
z This causes a cross cursor to appear in the projected image.
Cross cursor
5. Use the cursor keys to move the cross cursor to the location where
you want the upper left corner of the selection boundary to be.
6. Press the [ENTER] key.
z This fixes the current cross cursor location as the upper left corner of the selection
boundary.
100
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Setup Menu
7. Use the cursor keys to move the cross cursor and draw the
selection boundary.
Pressing the cursor key
moves the lower right corner
of the selection boundary.
8. When the area you want to capture is enclosed by the selection
boundary, press the [ENTER] key.
z This causes the message “Start image capture and registration as custom logo?” to
appear.
9. Press the [ENTER] key to capture the image enclosed by the
selection boundary.
z After a few moments, a dialog box with the message “Image capture and
registration as custom logo complete!” appears to let you know when the capture
operation is complete.
10.To view the custom logo (captured image), press the [ENTER] key.
z This projects the custom logo. After you are finished viewing it, press the [ESC] key
to return to custom logo setting screen in step 3.
11. Press the [MENU] key to exit the setup menu.
101
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Setup Menu
Configuring Custom Logo Capture Settings
Before capturing a custom logo, configure the following settings to control its position,
zoom, and other parameters when it is projected.
Setting
Available Items (Parentheses indicate defaults.)
Top, (Center), Bottom
Logo Vertical
Logo Horizontal
Custom Logo Zoom
Background Color
Resolution
Left, (Center), Right
(100%), 200%, Resize Image To Fit
(White), Black
(Normal), High
z The “Logo Vertical”, “Logo Horizontal”, and “Background Color” settings are not used
when the zoom setting is “Resize Image To Fit”.
z Note that you cannot change the above settings for a custom logo after you capture it.
z The following are some examples of how the above settings affect the custom logo.
Logo Vertical: Center
Logo Vertical: Center
Logo Horizontal: Center
Custom Logo Zoom: 100%
Background Color: White
Logo Horizontal: Center
Custom Logo Zoom: 200%
Background Color: White
Logo Vertical: Bottom
Logo Horizontal: Left
Custom Logo Zoom: 100%
Logo Vertical: Center
Logo Horizontal: Center
Custom Logo Zoom: 100%
Background Color: Black
Background Color: White
z
If an error occurs with the “High” resolution setting, try changing the resolution setting to
“Normal”. This will increase the chance of a successful capture. If you experience
problems capturing with the “Normal” setting, it may also mean that the area you are
trying to capture is too large. Try selecting a smaller area.
102
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Setup Menu
To configure custom logo settings
1. Perform steps 2 and 3 under “To capture a custom logo” on page
100 to display the custom logo setting screen.
2. Use the [S] and [T] keys to select the custom logo item whose
setting you want to change.
3. Use the [W] and [X] keys to select the setting you want. The button
next to the currently selected setting is black ( ).
z
4. Repeat steps 2 and 3 to configure all of the custom logo settings
you want.
5. After you are finished, press the [MENU] key to exit the setup menu.
To view the current custom logo
1. Perform steps 2 and 3 under “To capture a custom logo” on page
100 to display the custom logo setting screen.
2. Use the [S] and [T] keys to select “View Custom Logo”, and then
press the [ENTER] key.
z This projects the currently registered custom logo.
3. To return to the custom logo setting screen, press the [ESC] key.
4. Press the [MENU] key to exit the setup menu.
103
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Setup Menu
To initialize the custom logo
z Initializing custom logo settings clears the currently registered custom logo and returns all
of the settings of the custom logo setting screen to their initial defaults.
1. Perform steps 2 and 3 under “To capture a custom logo” on page
100 to display the custom logo setting screen.
2. Use the [S] and [T] keys to select “Initialize Custom Logo Settings”,
and then press the [ENTER] key.
z This displays a confirmation message asking if you want to initialize custom logo
settings.
3. Use the [S] and [T] keys to select [Yes].
4. Press the [ENTER] key to initialize the custom logo settings, or the
[ESC] key to exit the initialize operation without doing anything.
z Pressing the [ENTER] key initializes settings and returns to the custom logo settings
screen.
z Pressing the [ESC] key returns to the custom logo settings screen without initializing
anything.
5. Press the [MENU] key to exit the setup menu.
z Initializing the custom logo settings and deleting the custom logo causes the projector’s
preset logo to appear when “Logo” is selected for the startup screen (page 87), no
signal screen (page 87), and mute screen (page 88).
104
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Setup Menu
IOption Settings1 Language
J
This sub-menu lets you specify the language to use for messages, setup menus, etc.
z
Note that the choice of languages will depend on whether your projector’s serial number
starts with the letter A (such as: A791AA42...) or the letter B (such as: B791AA42...).
Input Source Specific Menu Items
Input Source
RGB
Available Items
A Model: English, French, German, Italian, Spanish, Swedish,
Korean, Japanese
B Model: English, Spanish, Chinese (Simplified),
Chinese (Traditional), Japanese
Component
S-VIDEO
VIDEO
No Signal
Setting Storage
A single setting is stored, which is applied to all input sources.
z This setting is required the first time you turn on the projector. For more information, see
“Specifying the Display Message Language” on page 43.
IOption Settings1
Alert Tones
J
This sub-menu lets you turn alert tones on and off.
Input Source Specific Menu Items
Input Source
RGB
Available Items (Parentheses indicate defaults.)
(On), Off
Component
S-VIDEO
VIDEO
No Signal
Setting Explanations
On: Turns on error alert, which sounds a tone when an error occurs.
Off: Turns off error alert.
Setting Storage
A single setting is stored, which is applied to all input sources.
z For details about the alert tone that sounds for each type of error when the alert tone is
turned on, see “Indicators and Alert Tones” on page 119.
105
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Setup Menu
IOption Settings1 Restore Menu Defaults
J
This sub-menu returns all of the sub-menu items on the Option Settings1 main menu to their
initial default settings.
z
z
z
You can perform initialization even when there is no input signal. In this case, the
initialization is performed for the currently selected input source.
The Auto Adjust item is initialized only when RGB is selected as the input source. All
other items are always initialized, regardless of the currently selected input source.
For details about the initialization procedure, see “To initialize the settings of a particular
main menu item” on page 74.
Option Settings2
IOption Settings2
AF/AK Mode
J
This sub-menu item specifies the [AF/AK] key function.
Input Source Specific Menu Items
Input Source
RGB
Available Items (Parentheses indicate defaults.)
(AF/AK), Continuous AF/AK, AF
Component
S-VIDEO
VIDEO
No Signal
Setting Explanations
AF/AK:
Assigns the AF/AK Mode to the [AF/AK] key. Pressing the [AF/
AK] key while this setting is selected performs Auto Focus and
auto keystone correction.
Continuous AF/AK:
Assigns the Continuous AF/AK Mode to the [AF/AK] key.
Pressing the [AF/AK] key while this setting is selected displays
an alignment chart and performs a continuous Auto Focus
operation. Pressing the [AF/AK] key again performs auto keystone
correction.
AF:
Assigns the AF Mode to the [AF/AK] key. Pressing the [AF/AK]
key while this setting is selected performs Auto Focus only.
Setting Storage
A single setting is stored, which is applied to all input sources.
z For details about [AF/AK] key operation and the various modes that can be assigned to
it (AF/AK Mode, Continuous AF/AK Mode, AF Mode), see “Auto Keystone Correction and
Auto Focus” (page 53).
106
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Setup Menu
IOption Settings2 Power On AF/AK Mode
J
You can specify either of two different auto adjustment operations to be performed whenever
the projector is turned on.
Input Source Specific Menu Items
Input Source
RGB
Available Items (Parentheses indicate defaults.)
Continuous AF/AK, (Off)
Component
S-VIDEO
VIDEO
No Signal
Setting Explanations
Continuous AF/AK:
Turning on the projector while this setting is selected displays an
alignment chart and performs a continuous Auto Focus operation.
Pressing the [AF/AK] key at this time performs auto keystone
correction.
Off:
Turning on the projector while this setting is selected restores the
focus and keystone correction settings that were in effect when
the projector was last turned off.
Setting Storage
A single setting is stored, which is applied to all input sources.
z When Continuous AF/AK is selected as the power on AF/AK mode, a custom logo is not
projected when power is turned on even if one is specified as the startup screen (page
87).
z For more information about Continuous AF/AK, see “Auto Keystone Correction and Auto
Focus” (page 53).
z For information about the focus setting, see “To focus the image” (page 50). For
information about keystone correction, see “Keystone Correction (KEYSTONE)” (page 53).
z When Continuous AF/AK is turned off, turning off projector power while focus is near its
maximum or minimum setting can cause the projected image to be out of focus the next
time power is turned on. If this happens, adjust focus manually or press the [AF/AK] key.
107
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Setup Menu
IOption Settings2 Zoom Memory
J
Zoom memory lets you save the zoom setting when the projector is turned off, so it can be
restored automatically the next time the projector is turned on.
Input Source Specific Menu Items
Input Source
RGB
Available Items (Parentheses indicate defaults.)
On, (Off)
Component
S-VIDEO
VIDEO
No Signal
Setting Explanations
On: Turning on the projector while this setting is selected restores the zoom setting
that was in effect when the projector was last turned off.
Off: Turning on the projector while this setting is selected causes the image to be
projected at its maximum size.
Setting Storage
A single setting is stored, which is applied to all input sources.
z For details about the zoom setting, see “To adjust image size” (page 50).
IOption Settings2
Restore Menu Defaults
J
This sub-menu returns all of the sub-menu items on the Option Settings2 main menu to their
initial default settings.
z
You can perform initialization even when there is no input signal. In this case, the
initialization is performed for the currently selected input source.
For details about the initialization procedure, see “To initialize the settings of a particular
main menu item” on page 74.
z
108
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Setup Menu
Operational Info
IOperational Info
Lamp Time
J
This sub-menu item shows the cumulative number of hours the current lamp has been used
to date.
Use this value as a reference when deciding whether or not the current lamp needs to be
replaced. For details about replacing the lamp, see “Replacing the Lamp” on page 111.
IOperational Info
Reset Lamp Time
J
Use this submenu item to reset the lamp time to 0 hours. For details about replacing the
lamp and the initialization procedure, see “Replacing the Lamp” on page 111.
IOperational Info
Input Signal
J
This sub-menu item shows the currently selected input signal (RGB, Component, S-VIDEO, or
VIDEO). “None” is indicated here when there is no input signal.
IOperational Info
Signal Name
J
This sub-menu item shows the signal name of the signal input to the projector. The “Signal
Name” column of the table under “Supported Signals” on page 126 shows the signal names
that are displayed by this sub-manu item.
IOperational Info
Index
J
This sub-menu item appears only when RGB or Component is the input signal. It shows
projector internal information.
IOperational Info
Resolution
J
This sub-menu item appears only when RGB is the input signal, and shows the resolution of
the RGB input signal in terms of vertical and horizontal pixels.
IOperational Info
Horizontal Frequency
J
This sub-menu item appears only when RGB, Component, S-VIDEO, or VIDEO is the input
signal. It shows the horizontal frequency of the input signal.
IOperational Info
Vertical Frequency
J
This sub-menu item appears only when RGB, Component, S-VIDEO, or VIDEO is the input
signal. It shows the vertical frequency of the input signal.
IOperational Info
Scan System
J
This sub-menu item appears only when RGB or Component is the input signal, and shows
the scanning frequency of the input signal. The input signal is interlace or non-interlace for
RGB signal input, and interlace or progressive for Component signal input.
109
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Setup Menu
Restore All Defaults
IRestore All Defaults
Restore All Defaults
J
This sub-menu returns all of sub-menu items on all main menus to their initial default
settings. This operation can be performed regardless of the currently selected input source
and regardless of whether or not a signal is currently being input.
For details about this initialization procedure, see “To initialize all menu settings” on page 75.
110
Download from Www.Somanuals.com. All Manuals Search And Download.
User Maintenance
User Maintenance
This section explains user maintenance procedures, including lamp replacement and projector
cleaning.
Cleaning the Projector
Always turn off the projector before cleaning it.
Cleaning the Projector Exterior
Wipe the exterior of the projector with a soft cloth that has been moistened in a weak
solution of water and a mild neutral detergent. Be sure to wring all excess moisture from the
cloth before wiping.
Never use benzene, alcohol, thinner, or any other volatile agent for cleaning.
Cleaning the Lens
Carefully wipe the lens with a commercially available lens cloth or optical lens paper, like
those for eyeglasses or camera lenses. When cleaning the lens, be very careful to avoid
scratching it.
Cleaning the Sensors
Carefully wipe the sensors with a commercially available lens cloth or optical lens paper, like
those for eyeglasses or camera lenses.
Replacing the Lamp
z
Continued use of a lamp that has passed its lamp life increases
the risk of the lamp rupturing. Replace the lamp with a new one
as soon as possible after the replacement message appears.
Caution
z
The light source lamp is a consumable item. The average life of a lamp is approximately
2000 hours. After 2000 hours, a message appears to alert you to the need of lamp
replacement. However, note that the characteristics of a particular lamp or lamp operating
conditions can cause the lamp to start to go dim or even fail before the message
appears.
To check the current lamp use time
1. Press the [MENU] key to display the setup menu.
111
Download from Www.Somanuals.com. All Manuals Search And Download.
User Maintenance
2. Press the [T] key to select the “Operational Info” main menu.
z The “Lamp Time” sub-menu item shows the number of hours that the current lamp has
been used.
3. Press the [MENU] key to exit the setup menu.
When to replace the lamp
The LAMP indicator starts to flash red and the message shown below appears whenever the
lamp time exceeds 2000 hours.
It is time to replace the lamp. Use the procedure in the User’s Guide to replace the lamp
as soon as possible.
When this message appears, replace the lamp as soon as possible using the procedure
under “Replacing the Lamp” on page 113.
Note that the above message will disappear about 10 seconds after you turn on the projector,
even if you do not replace the lamp.
You will be able to continue using the projector without replacing the lamp until the lamp time
reaches 100 hours. At that time, the LAMP indicator will stop flashing and remain lit red, the
following message will appear for about 10 seconds, and then the projector will turn off
automatically.
The lamp has exceeded its service life! The projector will not turn on until you replace the lamp.
When this message appears, replace the lamp immediately using the procedure under
“Replacing the Lamp” on page 113.
112
Download from Www.Somanuals.com. All Manuals Search And Download.
User Maintenance
Replacing the Lamp
z
During normal use, the lamp and the area around it become
extremely hot. Before replacing the lamp, turn off the projector
and wait for the cool down operation (indicated when the
POWER/STANDBY indicator is flashing amber) to finish. Next,
disconnect the AC power cord from the projector, and wait for at
least 60 minutes to allow it to cool down even further.
Touching the lamp or the area around it during operation or
immediately after turning off the projector creates the risk of
serious burn injury.
z
z
Replace the lamp using the YL-40 optional lamp cartridge only.
The projector uses a mercury lamp with high internal pressure
as its light source. A lamp that is weakened by impact, damage,
or expiration of its lamp life may explode or fail to light.
Note that the performance of the lamp differs greatly from lamp
to lamp, and due to conditions under which a lamp is used.
Never touch the glass of the lamp with your fingers. Doing so
can cause the lamp to rupture and shorten its life.
A broken lamp can cause glass fragments to be scattered inside
the lamp housing. Gas inside of the lamp housing may also be
discharged from the projector’s vent exhaust ports. Gas inside of
the lamp includes mercury, so be sure to ventilate the area
whenever the lamp breaks. Should you accidentally inhale gas
fumes or should gas fumes get into your eyes, immediately
contact a physician.
Caution
z
z
z
z
Should the lamp break, take care to avoid personal injury on the
glass fragments. Never try to replace a broken lamp on your
own. Be sure to contract your original dealer or authorized
CASIO service center to request replacement.
The lamp contains mercury. Dispose of old lamps in accordance
with the rules and regulations of your local jurisdiction.
zDisposing of the Lamp (U.S.A. Only)
This product utilizes a lamp containing mercury. Disposal of the lamp
may be regulated due to environmental considerations. For disposal or
recycling information, please contact your local authorities or the
Electronic Industries Alliance: http://www.eiae.org.
113
Download from Www.Somanuals.com. All Manuals Search And Download.
User Maintenance
To replace the lamp
z When replacing the lamp, use the special screwdriver that comes with the YL-40
replacement lamp. The projector does not come with a screwdriver.
1. Turn off the projector and unplug its AC power cord.
2. Wait for about 60 minutes to allow the projector’s current lamp to cool
down completely.
3. Turn over the projector and place it on top of a desk or on some other
stable surface.
4. Loosen the lamp cover screws, and then remove the lamp cover.
Lamp cover
114
Download from Www.Somanuals.com. All Manuals Search And Download.
User Maintenance
5. Loosen the three screws securing the lamp cartridge.
Screws
Lamp cartridge
6. Use the lamp cartridge handle to pull the lamp cartridge from the
projector.
115
Download from Www.Somanuals.com. All Manuals Search And Download.
User Maintenance
7. Insert the new lamp cartridge as far as it will go, as shown in the
illustration.
z After inserting the lamp cartridge, lay its handle down in the position shown in the
illustration under step 5 on page 115.
Make sure that the grooves on either side of the
lamp cartridge align properly with the grooves on
either side of the lamp housing.
z Never touch the lamp with your
hand. Doing so can cause the lamp
to rupture and shorten its life.
8. Secure the lamp cartridge with the three screws.
9. Return the lamp cover to its original position, and secure it with the
two screws.
z After replacing the lamp, be sure to perform the procedure under “Resetting the Lamp
Time” on page 117.
116
Download from Www.Somanuals.com. All Manuals Search And Download.
User Maintenance
Resetting the Lamp Time
The reset lamp time operation you need to perform depends on when you replace the lamp.
It is time to replace the lamp. Use the procedure in the User’s Guide to replace the lamp
as soon as possible.
If you replace the lamp when the above message appears, use the procedure under “To
reset the lamp time” on page 117.
The lamp has exceeded its service life! The projector will not turn on until you replace the
lamp.
If you replace the lamp after the above message appears, use the procedure under “To reset
the lamp time after exceeding the lamp life” on page 118.
To reset the lamp time
1. Use the procedure under “To turn on the projector” on page 41 to turn
on the projector
.
z There is no need to connect a computer or video device to the projector if you plan
only to reset the lamp time.
2. Press the [MENU] key to display the setup menu.
3. Press the [T] key to select “Operational Info”, and then press the
[ENTER] key.
z On the sub-menu that appears, select “Reset Lamp Time”.
4. Press the [ENTER] key.
z This causes the message “Reset lamp time?” to appear.
117
Download from Www.Somanuals.com. All Manuals Search And Download.
User Maintenance
5. Press the [S] key to select “Yes”, and then press the [ENTER] key.
z This resets the lamp time to 0 hours.
6. Press the [MENU] key to exit the setup menu.
z This causes the setup menu to disappear from the projected image.
To reset the lamp time after exceeding the lamp life
If you use the existing lamp until its life is exceeded, you will not be able to turn on the
projector even after you replace the lamp with a new one. Perform the following procedure to
initialize the lamp time in this case, which will make it possible to turn on the projector.
1. Use the bundled AC power cord to plug the projector into a power
outlet.
z Connecting to a power outlet causes the POWER/STANDBY and LAMP indicators on
the top of the projector to light red, which indicates that the lamp has exceeded its
service life.
2. While holding down the projector’s [W] key, hold down the [AUTO] key
for about five seconds.
z This will reset the lamp time, cause the POWER/STANDBY indicator to change from red
to amber, and also cause the LAMP indicator to go out.
3. Press the [ ] (power) key to ensure that the projector turns on
normally.
118
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Troubleshooting
This section explains how to interpret the projector’s indicators, and what you need to do
when you experience problems with projector operation.
Indicators and Alert Tones
The status of the indicators let you know the current operational status of the projector. This
section provides details about indicators, and about the error alert tones.
TEMP indicator
LAMP indicator
POWER/STANDBY indicator
TEMP
LAMP
AUTO
POWER/STANDBY
INPUT
ZOOM
AF/AK
Normal Operation Indicators
z
“POWER” in the following table stands for the “POWER/STANDBY” indicator.
When this indicator Is this
It means this
See page
POWER:
TEMP:
Amber steady
Amber steady
Amber steady
You have just plugged the AC cord into
a power outlet. Wait until the projector
enters the standby state (see below)
before trying to turn on power.
41
LAMP:
Standby state: The AC power cord is
plugged in and the projector is in
standby.
POWER:
Amber steady
41
Projector is warming up after being
turned on.
POWER:
POWER:
POWER:
LAMP:
Green flashing
Green steady
Amber flashing
Green steady
Projector is on and standing by for use.
Projector is cooling down after being
turned off.
44
93
Projector is in the low noise mode.
119
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Error Indicators
z
z
“POWER” in the following table stands for the “POWER/STANDBY” indicator.
“ ” in the “Alert” column indicates that the projector will emit four long beeps when an
error occurs. “U” in the “Alert” column indicates that the projector will emit two short
beeps when an error occurs. Note that alert tones sound only when “On” is specified for
“Option Settings1 J Alert Tones”.
z
When an error occurs, wait until cool down is complete and the fan stops before
unplugging the AC power cord. If you unplug the AC power cord while the fan is still
operating, an error may occur when you plug the AC power cord back in.
Indicator
Alert
Description
An operational problem was caused by external noise
or some other factor. After confirming that the
POWER/STANDBY indicator is lit red (steady) and
that the fan has stopped, unplug the AC power cord.
After the indicator goes out, plug the AC power cord
back in and turn on the projector again. If the error
occurs again when you turn power back on, contact
your original dealer or authorized CASIO Service
Center.
POWER : Amber flashing J
Red steady
TEMP
: Red steady
There is some problem with the fan.
POWER : Amber flashing J
After confirming that the POWER/STANDBY indicator
is lit red (steady) and that the fan has stopped,
unplug the AC power cord. After the indicator goes
out, plug the AC power cord back in and turn on the
projector again. If the error occurs again when you
turn power back on, contact your original dealer or
authorized CASIO Service Center.
Red steady
TEMP
: Red flashing
(0.5-second interval)
POWER : Amber flashing J
Power has turned off automatically due to internal
overheating. Perform the following steps.
1 After confirming that the POWER/STANDBY
indicator is lit red, unplug the AC power cord
and wait for about 60 minutes to allow the
projector to cool down.
Red steady
TEMP
: Red flashing
(1-second interval)
2 Check for any blocking of the projector’s intake
vents and exhaust vents, and make sure that
there is sufficient space around the projector.
) “Setup Precautions” (page 33).
3 Plug the AC power cord back in, and turn on
the projector again.
120
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Indicator
Alert
Description
POWER : Amber flashing J
Power has turned off automatically due to a lamp
problem.
Red steady
After confirming that the POWER/STANDBY
indicator is lit red, unplug the AC power cord,
then plug it back in and turn on the projector
again. If this does not correct the problem, wait
for the projector to cool down and then check the
lamp cartridge for damage. If there is nothing
wrong with the lamp cartridge, take it to your
original dealer or authorized CASIO Service
Center.
TEMP
LAMP
: Red flashing
(0.5-second interval)
: Red flashing
(0.5-second interval)
POWER : Amber flashing J
Power has turned off automatically because the
lamp cover is open. Perform the following steps.
1 After confirming that the POWER/STANDBY
indicator is lit red, unplug the AC power cord
and wait for about 60 minutes to allow the
projector to cool down.
Red steady
TEMP
: Amber flashing
2 Close the lamp cover.
) “To replace the lamp” (page 114).
3 Plug the AC power cord back in, and turn on
the projector again.
POWER : Amber flashing J
Internal memory error.
Red steady
After confirming that the POWER/STANDBY
indicator is lit red, unplug the AC power cord, wait
for about 60 minutes to allow the projector to cool
down, and then take it to your original dealer or
authorized CASIO Service Center.
TEMP
: Red flashing (2-second
interval)
POWER : Green steady
U
It is time to replace the lamp.
Replace the lamp following the steps under
“Replacing the Lamp” on page 111.
LAMP
: Red flashing
(1-second interval)
POWER : Amber flashing J
The allowable life for the lamp has been
exceeded, and the projector will not turn on.
Replace the lamp following the steps under
“Replacing the Lamp” on page 111.
Red steady
LAMP
: Red steady
121
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Projector Troubleshooting
Check the following items whenever you experience any problem with the projector.
Problem
Cause and Recommended Action
See page
The projector does not turn
If the POWER/STANDBY indicator is not lit, the
AC power cord may not be connected correctly.
J Make sure the AC power cord is connected
correctly to the projector and the power outlet.
41
on when I press the [
(power) key.
]
If the TEMP or LAMP indicator remains flashing
or lit, it means some type of error has occurred.
J See “Error Indicators”.
120
The projector does not
project any image from the
connected device.
The connected computer or video device may not
be turned on, or it may not be outputting a video
signal.
—
J Make sure the connected computer or video
device is turned on, and perform the required
operation on it to output a video signal.
The correct output source is not selected on the
projector.
J On the projector, select the input source that
corresponds to the device whose image you
are trying to project.
48
39
89
The projector does not
correctly project the image
from the connected device.
Images may not project correctly when you have
the component output terminal of a video device
connected to the RGB terminal of the projector.
J Try using the projector’s VIDEO input terminal
or S-VIDEO input terminal.
Images sent from a computer over an RGB cable
may not project correctly if [Component] is
selected for the “Input Settings J RGB Input”
menu setting.
J Turn off the projector and disconnect the AC
cord and RGB cable. Next, reconnect the AC
cord only and turn on power. Change the
“Input Settings J RGB Input” menu setting to
[RGB]. Try projecting again.
122
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Problem
Cause and Recommended Action
See page
When RGB/Component is
selected as the input
source, the color of the
projected image or the
image itself is abnormal.
The settings configured on the setup menu’s
“Input Settings J RGB Input” menu may not be
compatible with the device connected to the RGB
input terminal.
J Use the setup menu to configure the “Input
Settings J RGB Input” menu settings to correct
the problem.
89
The projector keys to not
work.
Key lock or power on password may be turned
on.
94
J Turn off key lock and/or power on password.
The remote controller does
not work.
The remote controller batteries may be dead.
J Replace the batteries.
27
29
The remote controller may be too far from the
projector.
J Make sure the remote controller is within the
allowable range when you operate it.
The auto keystone
correction function (AF/AK)
does not work correctly.
The sensors may have finger smudges or dirt on
them.
J Carefully wipe the sensors with a commercially
available lens cloth or optical lens paper, like
those for eyeglasses or camera lenses.
111
There may be an obstruction between the
sensors and the screen.
_
J Remove the obstruction.
The TEMP or LAMP
indicator is flashing or lit.
J See “Error Indicators”.
120
111
The message “It is time to
replace the lamp.” is being
projected.
It is time to replace the lamp.
J Replace the lamp.
The message “The lamp
has exceeded its service
life!.” is being projected.
The allowable life for the lamp has been
exceeded, and the projector will not turn on.
J Replace the lamp.
111
123
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Appendix
Specifications
Model Name
Projection System
DMD
XJ-450
DLP (DMD, single panel)
0.7inch
Size
×
Number of
Pixels
XGA (1024 768)
×
Projection Lens
Auto, optical zoom ( 2); auto focus
F = 2.0 to 2.8 f = 20 to 40mm
Light Source
250W high-pressure mercury lamp
×
RGB input terminal
RGB mini D-Sub 15-pin
1
(Also used as component signal input terminal.)
×
VIDEO input terminal
S-VIDEO input terminal
Audio input terminal
Audio output
RCA pin jack
Mini DIN4-pin
1
×
1
×
Stereo mini jack
1W monaural
USB TYPE B
1
USB port
Environment
Operating Temperature: 5 to 35°C (41 to 95°F)
Operating Humidity: 20 to 80% (non-condensation)
Power Requirements
Dimensions
100-240V AC, 50/60Hz
×
×
278(W)
64(H) 197(D) mm (excluding projections)
×
×
(10.9
2.5
7.8 inch)
Weight
Approximately 2.4kg (5.3 lbs)
Display Languages
A Model: English, French, German, Italian, Spanish,
Swedish, Korean, Japanese
B Model: English, Spanish, Chinese (Simplified),
Chinese (Traditional), Japanese
* Specifications are subject to change without notice.
124
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Computer System Requirements for USB Connection
The following are the minimum Windows and Macintosh computer system requirements for
USB connection with the projector.
IWindows
IBM PC/AT or compatible computer with USB port and Windows 98, 98SE, Me, 2000
Professional, or XP preinstalled
IMacintosh
Macintosh computer with USB port and OS 8.6 to 9, 10.1, or 10.2 preinstalled
z Normal USB operation may not be possible under certain system configurations.
z Proper operation is not guaranteed on computers that have been upgraded from another
version operating system.
125
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Supported Signals
RGB Signal
Horizontal
Frequency (kHz)
Vertical
Frequency (Hz)
Signal Name
Resolution
VESA
640 × 350/85
640 × 400/85
720 × 400/85
640 × 480/60
640 × 480/72
640 × 480/75
640 × 480/85
800 × 600/56
800 × 600/60
800 × 600/72
800 × 600/75
800 × 600/85
1024 × 768/43i
1024 × 768/60
1024 × 768/70
1024 × 768/75
1024 × 768/85
1152 × 864/75
1280 × 960/60
1280 × 960/85
1280 × 1024/60
1280 × 1024/75
1280 × 1024/85
1600 × 1200/60
640 × 480/67M13
832 × 624/75M16
1024 × 768/75M19 1024 × 768
1152 × 870/75M21 1152 × 870
640 × 480/117iM
800 × 600/95iM
1024 × 768/75iM
640 × 400/56
1400 × 1050/A
1400 × 1050/B
1152 × 864/70
1152 × 864/85
1280 × 960/75
640 × 350
640 × 400
720 × 400
640 × 480
640 × 480
640 × 480
640 × 480
800 × 600
800 × 600
800 × 600
800 × 600
800 × 600
1024 × 768
1024 × 768
1024 × 768
1024 × 768
1024 × 768
1152 × 864
1280 × 960
1280 × 960
1280 × 1024
1280 × 1024
1280 × 1024
1600 × 1200
640 × 480
832 × 624
37.9
37.9
37.9
31.5
37.9
37.5
43.3
35.2
37.9
48.1
46.9
53.7
35.5
48.4
56.5
60.0
68.7
67.5
60.0
85.9
64.0
80.0
91.1
75.0
35.0
49.7
60.2
68.7
56.0
59.0
59.0
24.8
64.0
64.0
64.0
77.5
75.0
85
85
85
60
73
75
85
56
60
72
75
85
87
60
70
75
85
75
60
85
60
75
85
60
67
75
75
75
117
95
75
56
59
60
70
85
75
APPLE
640 × 480
800 × 600
1024 × 768
640 × 400
1400 × 1050
1400 × 1050
1152 × 864
1152 × 864
1280 × 960
NEC
Other
126
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Component Signal
Horizontal
Frequency (kHz)
Vertical
Frequency (Hz)
Signal Name
1080i60
720p60
576p50
576i50
480p60
480i60
HDTV
SDTV
33.7
45.0
31.3
16.6
31.5
15.7
60
60
50
50
60
60
Video/S-Video Signal
Horizontal
Frequency (kHz)
Vertical
Frequency (Hz)
Signal Name
NTSC
NTSC4.43
PAL
PAL-M
PAL-N
PAL60
SECAM
15.7
15.7
15.6
15.7
15.6
15.7
15.6
60
60
50
60
50
60
50
* Listing of a device in the above table does not guarantee that you will be able to display
its images correctly.
* When “640 × 350/85” is the input signal, the “Operational Info” sub-menu items show 640 ×
400/85 information.
* When “1024 × 768/75iM” is the input signal, the “Operational Info” sub-menu items show
“1024 × 768/75” information.
* If you experience problems projecting the image of a “1280 × 1024/60”, “1400 × 1050/A” or
“1400 × 1050/B” signal, you may be able to obtain a correct image by changing to “Special
Signal”.
127
Download from Www.Somanuals.com. All Manuals Search And Download.
GUIDELINES LAID DOWN BY FCC RULES FOR USE OF THIS UNIT IN THE U.S.A. (not
applicable to other areas).
NOTICE
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communication. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
z
z
z
z
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC WARNING
Changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
Proper connectors must be used for connection to host computer and/or peripherals in order to meet
FCC emission limits.
Connector cable .......... XJ-450 unit to PC
Declaration of Conformity
Model Number:XJ-450
Trade Name:CASIO COMPUTER CO., LTD.
Responsible party:CASIO, INC.
Address:570 MT. PLEASANT AVENUE, DOVER, NEW JERSEY 07801
Telephone number:973-361-5400
This device complies with Part 15 of the FCC Rules, Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Tested To Comply With FCC Standards
FOR HOME OR OFFICE USE
Download from Www.Somanuals.com. All Manuals Search And Download.
Batterij niet weggooien,
maar inlevern als KCA
CASIO ELECTRONICS CO., LTD.
Unit 6, 1000 North Circular Road
London NW2 7JD, U.K.
Download from Www.Somanuals.com. All Manuals Search And Download.
MA0405-B
Download from Www.Somanuals.com. All Manuals Search And Download.
|