E
Digital Camera
User’s Guide
Thank you for purchasing this CASIO product.
• Before using it, be sure to read the precautions contained in this User’s Guide.
• Keep the User’s Guide in a safe place for future reference.
• For the most up-to-date information about this product, visit the official EXILIM
Website at http://www.exilim.com/
Download from Www.Somanuals.com. All Manuals Search And Download.
Read this first!
• The contents of this manual are subject to change without notice.
• The contents of this manual have been checked at each step of the production
process. Feel free to contact us if you notice anything that is questionable,
erroneous, etc.
• Any copying of the contents of this User’s Guide, either in part or its entirety, is
forbidden. Except for your own personal use, any other use of the contents of this
manual without the permission of CASIO COMPUTER CO., LTD. is forbidden
under copyright laws.
• CASIO COMPUTER CO., LTD. shall not be held liable for any damages or lost
profits suffered by you or any third party due to the use or malfunction of this
product.
• CASIO COMPUTER CO., LTD. shall not be held liable for any damages, lost
profits, or claims by third parties arising out of the use of Photo Transport or
YouTube Uploader for CASIO.
• CASIO COMPUTER CO., LTD. shall not be held liable for any damages or lost
profits caused by loss of memory contents due to malfunction, repair, or any other
reason.
• Note that the example screens and product illustrations shown in this User’s Guide
may differ somewhat from the screens and configuration of the actual camera.
LCD Panel
The liquid crystal panel of the monitor screen uses high-precision technology that
provides a pixel yield in excess of 99.99%. This means that some very small number
of pixels may not light or may remain lit at all times. This is due to the characteristics
of the liquid crystal panel, and does not indicate malfunction.
Take test shots
Before shooting your final image, shoot a test shot to ensure that the camera is
recording correctly.
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Contents
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Read this first! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
General Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Monitor Screen Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
What is a digital camera? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
First, charge the battery prior to use.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
To charge the battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
To load the battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Preparing a Memory Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
To load a memory card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
To format (initialize) a new memory card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Turning the Camera On and Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
To turn power on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
To turn off the camera. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Holding the Camera Correctly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
To shoot a snapshot. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Viewing Snapshots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Deleting Images. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
To delete a single file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
To delete all files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Snapshot Shooting Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Using the Control Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Selecting the Exposure Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Changing the Image Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Size) . . 35
Specifying ISO Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (ISO) . . 39
Shooting with Slow Motion View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Using Flash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(Flash) . . 44
Shooting with Zoom. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Using Continuous Shutter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Using Normal-speed Continuous Shutter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Contents
Download from Www.Somanuals.com. All Manuals Search And Download.
4
To record a movie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Recording a High-definition Movie. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Recording a High Speed Movie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
What is BEST SHOT? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Some Sample Scenes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
To shoot with BEST SHOT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Shooting with High Speed Night Scene
Digitally Correcting for Overexposure
Configuring the Camera to Help You Better Time
Your Shots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Lag Correction) . . 73
Basic Multi-motion image Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Shooting an Image in Accordance with
Using On-screen Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
REC Mode Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (REC) . . 88
❚
Selecting a Focus Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(Focus). . . 88
Using the Self-timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Self-timer). . . 91
Specifying the Auto Focus Area . . . . . . . . . . . . . . . . . . . . . . . . . . (AF Area). . . 93
Configuring the Continuous Shutter Image
Save Method. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Save CS Images). . . 96
Shooting with Quick Shutter . . . . . . . . . . . . . . . . . . . . . . . . .(Quick Shutter). . . 97
Displaying the On-screen Grid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Grid). . . 98
Contents
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Turning on Image Review . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(Review). . . 98
Using Icon Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Icon Help). . . 98
Image Quality Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Quality) . 100
Optimizing Image Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Lighting). . 101
Specifying Flash Intensity . . . . . . . . . . . . . . . . . . . . . . . . . (Flash Intensity). . 102
Using Built-in Color Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Color Filter). . 102
Controlling Color Saturation . . . . . . . . . . . . . . . . . . . . . . . . . . . (Saturation). . 102
Adjusting Image Contrast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Contrast). . 102
Viewing Snapshots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Viewing a Movie. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Deleting Continuous Shutter Images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Displaying the Image Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Rotating an Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Rotation) . 121
Resizing a Snapshot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(Resize) . 121
Copying Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Copy) . 122
Printing Snapshots. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Contents
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Using DPOF to Specify Images to be Printed
and the Number of Copies. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Uploading Movie Files to YouTube . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
User Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
Transferring Images Automatically and Managing Them
❚
on Your Macintosh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
User Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
Files and Folders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
Memory Card Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
Specifying the Date Style . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Date Style) . 156
Selecting the Screen Aspect Ratio
Contents
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Precautions during Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
Power Supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170
To replace the battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171
Using the Camera in another Country . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172
Using a Memory Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172
To replace the memory card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172
Reset Initial Default Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
When things don’t go right... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188
Contents
Download from Www.Somanuals.com. All Manuals Search And Download.
8
General Guide
The numbers in parentheses indicate the pages where each item is explained.
. Camera
Front
Back
12345
9
bkbl bm bn 6
6
bo
bp
bq
7
8
cm cl
ckbt bsbr
Zoom controller
Back lamp
Control button
1
bl
bm
bn
bo
bp
br
Shutter button (page 25)
Flash (page 44)
[ON/OFF] (Power)
(page 23)
[0] (Movie) button
(page 57)
Movie mode switch
(page 57)
[r] (REC) button
Terminal cover
[USB/AV] port
([8] [2] [4] [6])
[BS] button (page 66)
[MENU] button
(page 86)
[SET] button (page 32)
[p] (PLAY) button
Monitor screen
2
3
4
bs
bt
Front lamp
5
ck
cl
Strap hole (page 2)
Lens
Microphone (page 58)
[SLOW] (Slow Motion
View) (page 42)
6
7
8
9
cm
bq
bkÕ (Continuous Shutter)
(page 49)
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Monitor Screen Contents
The monitor screen uses various indicators, icons, and values to keep you informed
of the camera’s status.
• The sample screens in this section are intended to show you the locations of all the
indicators and figures that can appear on the monitor screen in various modes.
They do not represent screens that actually appear on the camera.
. Snapshot Recording
Remaining snapshot memory capacity
7
123456789
bk
bl
bm
bn
bo
bp
Number of recordable CS images
Exposure mode (page 33)
ISO sensitivity (page 39)
White balance setting (page 40)
Flash (page 44)
8
cn
cm
9
bk
bl
bm
bn
bo
bp
bq
br
bs
cl
ck
bt bsbrbq
Focus mode (page 88)
1
2
3
Metering mode (page 101)
Continuous Shutter mode
(page 49)
Self-timer mode (page 91)
Image deterioration indicator
(page 47)
Timestamp indicator (page 155)
Battery level indicator (page 18)
Histogram (page 161)
4
5
bt
ck
cl
cm
cn
Recording mode (page 25)
Face Detection (page 94)
6
NOTE
• The semi-transparent gray frame on the monitor screen indicates the area that is
recorded when shooting a movie. The area within the frame is recorded for a
movie.
• If the current aperture, shutter speed, ISO sensitivity, or Auto Exposure is not
correct, the setting will turn orange when you half-press the shutter button.
Download from Www.Somanuals.com. All Manuals Search And Download.
11
. Movie Recording
Recording mode (page 57)
1
2
3
4
5
6
1 2 3
Movie recording time (page 57)
Movie recording in progress (page 57)
Recording speed (high speed movie) (page 60)
4
5
6
. Snapshot Viewing
File type
1
2
3
4
5
6
7
8
9
bk
bl
bm
bn
bo
bp
bq
br
12 3 4
Protect indicator (page 119)
Snapshot image size (page 35)
Folder name/file name (page 149)
Snapshot image quality (page 100)
ISO sensitivity (page 39)
Aperture value
5
br
bq
bp
6
7
8
9
Shutter speed
Date/time (page 156)
Metering mode (page 101)
White balance setting (page 117)
Flash (page 44)
Battery level indicator (page 18)
Continuous Shutter mode (page 49)
Histogram (page 161)
bo bnbmbl bk
Exposure mode (page 33)
Download from Www.Somanuals.com. All Manuals Search And Download.
12
. Movie Playback
No audio data available
File type
1
2
3
4
5
6
7
8
9
123 4
Protect indicator (page 119)
Folder name/file name (page 149)
Movie recording time (page 103)
YouTube (page 64)
5
6
7
Date/time (page 156)
Battery level indicator (page 18)
9
8
. CS Image Viewing
Current image number/number of images in the
group (page 104)
1
1
2
Playback guide (page 104)
CS speed (page 104)
2
3
4
4
3
Download from Www.Somanuals.com. All Manuals Search And Download.
13
Quick Start Basics
What is a digital camera?
A digital camera stores images on a memory card, so you can record and
delete them a countless number of times.
Record
Delete
Play
You can use the images you record in a variety of different ways.
Store images on your
computer.
Print images.
Attach images to e-mail.
Quick Start Basics
Download from Www.Somanuals.com. All Manuals Search And Download.
14
What you can do with your CASIO camera
Your CASIO camera is packed with a powerful selection of features and functions to
make recording of digital images easier, including the following three main functions.
High Speed CS/Prerecord CS
Now you can shoot up to 30 continuous high-
resolution images at the amazing speed of
40 images per second (maximum). Prerecord CS
pre-records images to ensure you are almost never
too late with the shutter button.
High Speed Movie
Movies can be recorded at up to 1000 frames per
second. This makes it possible to clearly view
phenomena that are invisible to the human eye, in
slow motion.
HD Movie Recording
You can record movies in high-quality HD.
x
(1280 720 pixels 30 fps)
1280x720 pixels
Quick Start Basics
Download from Www.Somanuals.com. All Manuals Search And Download.
15
First, charge the battery prior to use.
Note that the battery of a newly purchased camera is not charged. Perform the steps
under “To charge the battery” to bring the battery to a full charge.
• Your camera requires a special CASIO rechargeable lithium ion battery (NP-40) for
power. Never try to use any other type of battery.
To charge the battery
+
1. Aligning the positive
and
-
negative terminals of the battery
with those of the charger unit, load
the battery into the charger unit.
2. Plug the charger unit into a
[CHARGE] lamp
household power outlet.
About 150 minutes are required to
reach full charge. The [CHARGE]
lamp will go out when charging is
complete. Unplug the power cord
from the power outlet and then
remove the battery from the charger.
Lamp Status
Lit Red
Description
Charging
Flashing Red
Charger unit or battery problem (page 170)
Charging complete or standing by, due to abnormally
high or low ambient temperature (page 170)
Off
Quick Start Basics
Download from Www.Somanuals.com. All Manuals Search And Download.
16
Other Charging Precautions
• Use the special charger (BC-31L) to charge the special lithium ion battery (NP-40).
Never use any other type of charger device. Attempting to use a different charger
can result in unexpected accident.
• A battery that is still warm due to normal use may not charge fully. Give the battery
time to cool before charging it.
• A battery discharges slightly even when it is not loaded in the camera. Because of
this, it is recommended that you charge the battery immediately before you need to
use it.
• Charging the camera’s battery may cause interference with TV and radio reception.
If this happens, plug the charger into an outlet that is further away from the TV or
radio.
• Actual charging time depends on current battery capacity and charging conditions.
To load the battery
1. Open the battery cover.
1
Slide the battery cover release in the direction
indicated by arrow
and then open the
1
battery cover as indicated by arrow
.
2
2
2. Load the battery.
Stopper
With the EXILIM logo on the
battery facing upwards (in the
direction of the monitor screen),
hold the stopper next to the
battery in the direction indicated
by the arrow as you slide the
battery into the camera. Press the
battery in until the stopper
secures it in place.
Battery contacts
EXILIM logo
Back
Front
Quick Start Basics
Download from Www.Somanuals.com. All Manuals Search And Download.
17
3. Close the battery cover.
• For information about how to replace the battery,
see page 171.
Checking Remaining Battery Power
As battery power is consumed, a battery indicator on the monitor screen indicates
remaining power as shown below.
Remaining Power
Battery Indicator
Indicator Color
High
Low
*
*
*
*
Cyan
*
Amber
Red
*
Red
indicates battery power is low. Charge the battery as soon as possible.
Recording is not possible when is indicated. Charge the battery immediately.
• The level shown by the battery indicator may change when you switch between the
REC mode and PLAY mode.
• Leaving the camera for about one day with no power supplied while the battery is
dead will cause its date and time settings to be cleared. A message telling you to
configure time and date settings will appear the next time you turn on the camera
after restoring power. When this happens, configure date and time settings (page
155).
Battery Power Conservation Tips
• When you do not need to use the flash, select ? (Flash Off) for the flash setting
• Enable the Auto Power Off and the Sleep features to protect against wasting
battery power when you forget to turn off the camera (pages 157, 157).
• Avoid unnecessary optical zoom operations.
Quick Start Basics
Download from Www.Somanuals.com. All Manuals Search And Download.
18
Configuring Basic Settings the First Time You Turn On the
Camera
The first time you load a battery into the camera, a screen appears for configuring the
display language, date, and time settings. Failure to set the date and time correctly
will cause the wrong date and time data to be recorded with images.
IMPORTANT!
• A screen for language selection will not appear in step 2 of the procedure below if
you purchased a camera intended for the Japanese market. To change the display
language from Japanese in this case, use the procedure under “Specifying the
the language you select may not be included with a camera intended for the
Japanese market.
[ON/OFF]
1. Press [ON/OFF] to turn on the
camera.
2. Use [8], [2], [4], and [6] to select
[BS]
the language you want and then
press [SET].
3. Use [8] and [2] to select a date style and then press [SET].
Example: July 10, 2012
YY/MM/DD * 12/7/10
DD/MM/YY * 10/7/12
MM/DD/YY * 7/10/12
4. Set the date and the time.
Use [4] and [6] to select the setting you want to
change and then use [8] and [2] to change it.
To switch between 12-hour and 24-hour format, press
[BS].
5. After setting the date and time, use [4] and [6]
to select “Apply” and then press [SET].
Quick Start Basics
Download from Www.Somanuals.com. All Manuals Search And Download.
19
If you make a mistake configuring display language, date, or time settings with the
above procedure, refer to the following pages for information about how to correct
the settings.
– Display language: Page 156
NOTE
• Each country controls its local time offset and the use of summer time, and so they
are subject to change.
• Removing the battery from the camera too soon after configuring time and date
settings for the first time can cause the settings to be reset to their factory defaults.
Do not remove the battery for at least 24 hours after configuring settings.
Preparing a Memory Card
Though the camera has built-in memory that can be used to store images and
movies, you probably will want to purchase a commercially available memory card for
greater capacity. The camera does not come with a memory card. Images recorded
while a memory card is loaded are saved to the memory card. When no memory card
is loaded, images are saved to built-in memory.
Supported Memory Cards
– SD Memory Card
– SDHC Memory Card
Use one of the above types of memory card.
• Use only SD cards that are compliant with the SD Card
Association specification.
. Memory Card Handling Precautions
Certain types of cards can slow down processing speeds, and even can make it
impossible to store High Quality movies correctly. Also, use of certain types of
memory cards slows down data transfer and increases the time it takes to record
movie data, which can result in movie frames being dropped. The Y indicator on the
monitor screen turns yellow to indicate that frames are being dropped. In order to
avoid problems such as these, use of an Ultra High Speed Type SD memory card is
recommended. Note, however that CASIO makes no guarantees about the operation
of any Ultra High Speed Type SD memory card used with this camera.
Quick Start Basics
Download from Www.Somanuals.com. All Manuals Search And Download.
20
To load a memory card
1. Press [ON/OFF] to turn off the
camera and then open the battery
cover.
1
2
Slide the battery cover release in the
direction indicated by arrow
and then
1
open the battery cover as indicated by
arrow
.
2
2. Load a memory card.
Positioning the memory card so its front
is facing upwards (towards the monitor
screen side of the camera), slide it into
the card slot all the way in until you hear
it click securely into place.
Front
Front
Back
3. Close the battery cover.
• For information about how to replace
the memory card, see page 172.
IMPORTANT!
• Never insert anything besides a supported
• Should water or any foreign object ever get into the card slot, immediately turn off
the camera, remove the battery, and contact your retailer or nearest CASIO
authorized service center.
Quick Start Basics
Download from Www.Somanuals.com. All Manuals Search And Download.
21
To format (initialize) a new memory card
You need to format a new memory card before using it for the first time.
1. Turn on the camera and press [MENU].
2. On the “Set Up” tab, select “Format” and then press [6].
3. Use [8] and [2] to select “Format” and then press [SET].
IMPORTANT!
• Formatting a memory card that already has snapshots or other files on it, will delete
its contents. Normally you do not need to format a memory card again. However, if
storing to a card has slowed down or if you notice any other abnormality, re-format
the card.
• Be sure to use the camera to format a memory card. Formatting a memory card on
a computer and then using it in the camera can slow down data processing by the
camera. In the case of an SD or SDHC memory card, formatting on a computer can
result in non-conformity with the SD format, causing problems with compatibility,
operation, etc.
• Before formatting a new Eye-Fi card to use it for the first time, copy the Eye-Fi
Manager install files to your computer. Do this before formatting the card.
Quick Start Basics
Download from Www.Somanuals.com. All Manuals Search And Download.
22
Turning the Camera On and Off
To turn power on
To enter the REC mode, press [ON/OFF] (Power) or
[r] (REC). To enter the PLAY mode, press [p]
(PLAY).
[ON/OFF] (Power)
The back lamp will light (green) momentarily and the
camera will turn on. If you are entering the REC mode,
the lens will extend from the camera at this time.
• Take care to ensure that nothing is restricting or
coming into contact with the lens as it extends.
Holding the lens with your hand so it cannot extend
creates the risk of malfunction.
Back lamp
• Pressing [p] (PLAY) while in the REC mode
switches to the PLAY mode.
157) will turn off power automatically if you do not
perform any operation for a preset amount of time.
[p] (PLAY)
[r] (REC)
To turn off the camera
Press [ON/OFF] (Power).
• You can configure the camera so power does not turn on when you press [r]
(REC) or [p] (PLAY). You also can configure the camera to turn off when you
Quick Start Basics
Download from Www.Somanuals.com. All Manuals Search And Download.
23
Holding the Camera Correctly
Your images will not come out clearly if you move the camera when you press the
shutter button. When pressing the shutter button, be sure to hold the camera as
shown in the illustration below, and keep it still by pressing your arms firmly against
your sides as you shoot.
Holding the camera still, carefully press the shutter button and take care to avoid all
movement as the shutter releases and for a few moments after it releases. This is
especially important when available lighting is low, which slows down the shutter
speed.
Horizontal
Vertical
Hold the camera so the flash is
above the lens.
NOTE
• Take care that your fingers and the
strap do not cover any of the areas
indicated in the illustration.
Flash
Front lamp
• To protect against accidentally
dropping the camera, attach the wrist
strap and make sure it is around your
fingers or wrist while you are operating
the camera.
Lens
Microphone
• Never swing the camera around by its
strap.
• The supplied strap is intended for use
with this camera only. Never use it for
any other purpose.
Strap
Quick Start Basics
Download from Www.Somanuals.com. All Manuals Search And Download.
24
To shoot a snapshot
The following procedure describes how to shoot a single snapshot. For information
about shooting a series of shots (Continuous Shutter), see page 49.
1. Press [r] (REC) to turn on the camera.
2. Press [SET].
3. Use [8] and [2] to select the top option in the
control panel (Exposure mode).
4. Use [4] and [6] to select t (Auto) and then press [SET].
Auto icon
Monitor screen
Shutter button
[r] (REC)
Remaining snapshot memory
capacity (page 184)
5. Point the camera
at the subject.
You can zoom the
image, if you want.
w Wide Angle
z Telephoto
Zoom controller
Quick Start Basics
Download from Www.Somanuals.com. All Manuals Search And Download.
25
6. Half-press the shutter button to focus the image.
When focus is complete, the camera will beep, the back lamp will light green, and
the focus frame will turn green.
• If the current aperture, shutter speed, ISO sensitivity, or Auto Exposure is not
correct, the setting will turn orange when you half-press the shutter button.
Focus frame
Back lamp
ISO sensitivity
Aperture value
Shutter speed
When you half-press the shutter button, the
camera automatically adjusts exposure and
focuses on the subject it is currently pointed
at. Mastering how much pressure is required
for a half-press and a full-press of the shutter
button is an important technique for good-
looking images.
Half-press
Press lightly
until the button
stops.
Beep, beep (Image is in focus.)
7. Continuing to keep the camera still, press the shutter button the rest of
the way down.
This records the snapshot.
Full-press
Snap (Image is recorded.)
Quick Start Basics
Download from Www.Somanuals.com. All Manuals Search And Download.
26
Shooting a Movie
[0] (Movie)
Press [0] (Movie) to start movie recording. Press [0] (Movie)
again to stop movie recording. See the following pages for
details.
Standard movie (STD movie): page 57
High-definition movie (HD movie): page 60
High speed movie (HS movie): page 60
. Using Quick Shutter
Fully pressing the shutting button without waiting for Auto Focus to operate will record
• With Quick Shutter, the camera focuses faster than normal Auto Focus, which
means you can capture quick moving action more easily. Note, however, that some
images may be out of focus when Quick Shutter is used.
• Whenever possible, take a little extra time to half-press the shutter button in order
to ensure proper focus.
. If the image does not focus...
If the focus frame stays red and the back lamp is flashing green, it means that the
image is not in focus (because the subject is too close, etc.). Point the camera at the
subject and try to focus again.
. If the subject is not in the center of the frame...
in which the subject to be focused on is not within the focus frame in the center of the
screen.
Quick Start Basics
Download from Www.Somanuals.com. All Manuals Search And Download.
27
Viewing Snapshots
Use the following procedure to view snapshots on the camera’s monitor screen.
• For information about images recorded using continuous shutter (CS), see page
1. Press [p] (PLAY) to enter the
PLAY mode.
• This will display one of the snapshots
currently stored in memory.
• Information about the displayed
• You also can clear the information to
[p] (PLAY)
view only the snapshot (page 161).
• You can zoom in on the image by
snapshot that is very important to you, it is recommended that you zoom the
image and check its details after recording it.
2. Use [4] and [6] to scroll between images.
• Holding down either button scrolls at high speed.
[6]
[6]
[4]
[4]
NOTE
• Half-pressing the shutter button while in the PLAY mode or while a menu screen is
displayed will switch directly to the REC mode.
Quick Start Basics
Download from Www.Somanuals.com. All Manuals Search And Download.
28
Deleting Images
If memory becomes full, you can delete images you no longer need in order to free up
storage and record more images.
IMPORTANT!
• Remember that a file (image) delete operation cannot be undone.
• For information about images recorded using continuous shutter (CS), see page
To delete a single file
1. Press [p] (PLAY) to enter the PLAY mode and then
press [2] (
).
2. Use [4] and [6] to scroll through the files until the one you want to
delete is displayed.
3. Use [8] and [2] to select “Delete” and then press [SET].
• To delete other files, repeat steps 2 and 3.
• To exit the delete operation, press [MENU].
all of the images in the currently displayed CS group will be deleted.
To delete all files
1. Press [p] (PLAY) to enter the PLAY mode and then press [2] (
2. Use [8] and [2] to select “Delete All Files” and then press [SET].
).
3. Use [8] and [2] to select “Yes” and then press [SET] to delete all files.
This will cause the message “There are no files” to appear.
Quick Start Basics
Download from Www.Somanuals.com. All Manuals Search And Download.
29
Snapshot Shooting Precautions
Operation
• Never open the battery cover while the back lamp is flashing green. Doing so can
result in the image you just shot being saved incorrectly, damage to other images
stored in memory, malfunction of the camera, etc.
• If unwanted light is shining directly onto the lens, shade the lens with your hand.
Monitor Screen when Shooting Snapshots
• Subject brightness conditions can cause monitor screen response to slow and can
cause digital noise in the monitor screen image.
• The image that appears on the monitor screen is for image composition. The actual
Shooting Indoors under Fluorescent Lighting
• Minute flickering of fluorescent lighting can affect the brightness or color of an
image.
Other Precautions
• Due to the characteristics of the camera’s semiconductor, slow shutter speeds can
cause digital noise in images. The camera performs an automatic noise reduction
process whenever the shutter speed is 1 second or slower. Storage of images shot
at slower shutter speeds takes longer because of the time required for noise
reduction. Do not perform any key operation while the image storage operation is in
progress.
• A noise reduction process is performed when ISO sensitivity is set to a high value.
This can cause the camera to take relatively longer to be ready to shoot again after
you press the shutter button. Do not perform any key operation while the image
recording operation is in progress.
• Due to the characteristics of the imaging element used by the camera, very fast
moving objects in an image may appear distorted.
Quick Start Basics
Download from Www.Somanuals.com. All Manuals Search And Download.
30
Auto Focus Restrictions
• Any of the following can make proper focus impossible.
– Solid color wall or other very low contrast subject
– Strongly back lit subject
– Very shiny subject
– Blinds or other subject with a repeating horizontal pattern
– Multiple subjects at varying distances from the camera
– Subject in a dark location
– Subject that is too far away for light from the AF assist light to reach
– Camera movement while shooting
– Fast-moving subject
– Subjects outside the focus range of the camera
88).
Quick Start Basics
Download from Www.Somanuals.com. All Manuals Search And Download.
31
Snapshot Tutorial
Using the Control Panel
The control panel can be used to configure camera settings.
1. In the REC mode, press [SET].
[8] [2] [4] [6]
[SET]
2. Use [8] and [2] to select the setting you want to change.
This will select one of the control panel icons and display its settings.*1
Exposure mode (page 33)
ISO sensitivity (page 39)
White balance (page 40)
EV shift (page 41)
Not displayed in this mode
Flash (page 44)
Control panel
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
Date/Time (page 46)
*1 Items displayed in the control panel depend on the recording mode.
*2 Image quality cannot be changed using the control panel.
3. Use [4] and [6] to change the setting.
4. If you want to configure another setting, repeat steps 2 and 3.
5. After all of the settings are the way you want, press [SET].
This will apply the settings and return to the REC mode.
NOTE
• You also can use on-screen menus to configure settings other than those listed
Download from Www.Somanuals.com. All Manuals Search And DownSlonaapds.hot Tutorial
32
Selecting the Exposure Mode
Your camera has a variety of different exposure modes. Before shooting an image,
select the exposure mode that suits the type of subject you are shooting.
1. In the REC mode, press [SET].
2. Use [8] and [2] to select the top option in the control panel (Exposure
mode).
3. Use [4] and [6] to select the setting you want and then press [SET].
t
Auto
Use this setting for easy image recording. This is the mode you normally should
b
BEST SHOT
Simply select one of a collection of built-in sample scenes and the camera sets
A A (Aperture Priority) mode
In this mode, you select the aperture and other settings
are adjusted accordingly.
Press [SET] to open the control panel.
Use [8] and [2] to open the fifth control panel
option from the top (aperture, EV Shift).
1
2
Use [8] and [2] to select the aperture setting, and
then use [4] and [6] to change it.
3
Aperture value
• The ISO sensitivity, shutter speed and aperture
value on the monitor screen will turn orange when
you half-press the shutter button if the image is over-exposed or under-
exposed.
Download from Www.Somanuals.com. All Manuals Search And DownSlonaapds.hot Tutorial
33
S S (Shutter Speed Priority) mode
In this mode, you select the shutter speed and other
settings are adjusted accordingly.
Press [SET] to open the control panel.
Use [8] and [2] to open the fifth control panel
option from the top (shutter speed, EV Shift).
1
2
Use [8] and [2] to select the shutter speed setting,
3
and then use [4] and [6] to change it.
• The ISO sensitivity, shutter speed and aperture value
on the monitor screen will turn orange when you half-
press the shutter button if the image is over-exposed
or under-exposed.
Shutter speed
M M (Manual Exposure) mode
This mode gives you total control over aperture and
shutter speed settings.
Press [SET] to open the control panel.
Use [8] and [2] to open the fifth control panel
option from the top (aperture, shutter speed).
1
2
Use [8] and [2] to select the aperture setting, and
then use [4] and [6] to change it.
3
Aperture value
Shutter speed
Use [8] and [2] to select the shutter speed setting,
and then use [4] and [6] to change it.
[6] to focus the image.
4
IMPORTANT!
• You may not be able to achieve the brightness you want when shooting an image
that is very dark or very bright. If this happens, use the M mode to adjust the
aperture or shutter speed manually.
A
however, turn on “
Camera AS”, if you like.
setting. The ISO sensitivity setting cannot be changed while in the S mode.
• While A, S, or M is selected for the exposure mode, the flash will not fire if > (Auto
Flash) or ¥ (Red Eye Reduction) is selected as the flash mode. If you want the
flash to fire, select < (Flash On) as the flash mode.
Download from Www.Somanuals.com. All Manuals Search And DownSlonaapds.hot Tutorial
34
Changing the Image Size (Size)
. Pixels
A digital camera image is a collection of small
dots called “pixels”. The more pixels there are
in an image, the more detail there will be.
However, you generally can do with fewer
pixels when printing an image (L size)
through a print service, attaching an image to
e-mail, when viewing the image on a
computer, etc.
Pixel
. About image sizes
The size of an image indicates how many pixels it contains, and is expressed as
x
horizontal pixels vertical pixels.
x
10M (3648 2736) size image =
3648*
Approximately 10 million pixels
x
VGA (640 480) size image =
640*
Approximately 300,000 pixels
* Unit: pixels
Download from Www.Somanuals.com. All Manuals Search And DownSlonaapds.hot Tutorial
35
Image Size Selection Tips
Note that larger images have more pixels, so they take up more memory space.
More detail, but takes up more memory. Best
when you plan to print large-size prints (such
as A3 size).
Large Number
of Pixels
Small Number Less detail, but takes up less memory. Best
of Pixels
when you want to send images by e-mail, etc.
• For information about image size, image quality, and number of images that can be
stored, see page 184.
Download from Www.Somanuals.com. All Manuals Search And DownSlonaapds.hot Tutorial
36
. To select the image size
1. In the REC mode, press [SET].
2. Use [8] and [2] to select the second control panel option (Image
Size).
3. Use [4] and [6] to select an image size and then press [SET].
Suggested Print
Image Size
Size and
Description
(Pixels)
Application
10M
(3648 2736)
Poster Print
Poster Print
HDTV
x
3:2
Good detail for better clarity even for images
x
(3648 2432)
16:9
(3648 2048)
x
9M
A3 Print
x
(3456 2592)
7M
A3 Print
Good detail
x
(3072 2304)
4M
A4 Print
x
(2304 1728)
2M
Best when preserving memory capacity is
relatively more important than image quality.
x
3.5" 5" Print
x
(1600 1200)
Image files are smaller, which is better when
attaching images to e-mail. However, images
are relatively coarser.
VGA
(640 480)
E Mail
x
Download from Www.Somanuals.com. All Manuals Search And DownSlonaapds.hot Tutorial
37
• The initial factory default image size setting is 10M (10 million pixels).
• Selecting “3:2” records images with an aspect ratio of 3:2, which matches the
standard aspect ratio of print paper.
• The letters “HDTV” stand for “High Definition Television”. An HDTV screen has an
aspect ratio of 16:9, which makes them wider than the usual 4:3 aspect ratio of
television screens of the past. Your camera can record images that are compatible
with the aspect ratio an HDTV screen.
• You should regard the print paper sizes suggested here as guidelines only (200 dpi
print resolution).
• Available image sizes are limited for some functions as noted below.
This option cannot be selected in the High Speed CS mode or when using
10M, some BEST SHOT scenes*. Switching to the High Speed CS mode or
3:2, selecting some BEST SHOT scenes* while the “10M”, “3:2”, or “16:9”
16:9 image size is selected will cause the image size setting to change to “9M”
automatically.
This option can be selected in the High Speed CS mode or only when
using some BEST SHOT scenes*. Switching to another mode from the
9M
High Speed CS mode or selecting some BEST SHOT scenes* while the
“9M” image size is selected will cause the image size setting to change to
“10M” automatically.
* Applicable BEST SHOT scenes: “Move In CS”, “Move Out CS”, “High Speed
Anti Shake”, “High Speed Night Scene”, “High Speed Night Scene and Portrait”,
“Multi-motion Image”, “High Speed Best Selection”, “Lag Correction”, “High
Speed Lighting”, “Expression CS”, “Baby CS”, “Child CS”, “Pet CS”, “Sports CS”
Download from Www.Somanuals.com. All Manuals Search And DownSlonaapds.hot Tutorial
38
Specifying ISO Sensitivity (ISO)
ISO sensitivity is a measure of sensitivity to light.
1. In the REC mode, press [SET].
2. Use [8] and [2] to select the third control panel option from the top
(ISO Sensitivity).
3. Use [4] and [6] to select the setting you want and then press [SET].
AUTO
Adjusts sensitivity automatically according to conditions
Lower
sensitivity
Slow shutter speed
Less noise
ISO 100
ISO 200
ISO 400
ISO 800
ISO 1600
ISO 3200
Fast shutter speed (Set
for shooting in dimly lit
areas.)
Some coarseness
(increased digital
noise)
Higher
sensitivity
• In the S (shutter speed priority) mode, ISO sensitivity always operates
according to its “AUTO” setting. The ISO sensitivity setting cannot be changed
while in the S mode.
• The current ISO sensitivity setting is used when shooting a high speed movie
in the M (manual exposure) mode. For all other types of movies, “AUTO” is
used as the ISO sensitivity setting.
“AUTO”.
• Higher ISO sensitivity values tend to result in digital noise in images.
• Since higher ISO sensitivity values tend to result in digital noise in images, the
camera performs a noise filtering process. Because of this, it may take
relatively longer for the camera to finish recording an image after it is shot. You
will not be able to perform any key operation while image recording is in
progress.
Download from Www.Somanuals.com. All Manuals Search And DownSlonaapds.hot Tutorial
39
Adjusting White Balance (White Balance)
You can adjust white balance to match the source of light available where you are
shooting and avoid the blue cast that results when shooting outdoors when it is
cloudy, and the green cast that results when shooting under fluorescent lighting.
1. In the REC mode, press [SET].
2. Use [8] and [2] to select the fourth control panel option from the top
(White Balance).
3. Use [4] and [6] to select the shooting condition you want and then
press [SET].
‡
¤
Auto WB
Daylight
Configures the camera to adjust white balance automatically
For shooting outdoors on a clear day
For shooting outdoors on an overcast rainy day, in the
shade, etc.
'
“
Overcast
Shade
For shooting on a clear day in the shade of trees or buildings
For shooting under white or day white fluorescent lighting
†
Day White
Fluorescent
–
Daylight
Fluorescent
For shooting under daylight fluorescent lighting
For shooting under light bulb lighting
«
·
Tungsten
For configuring the camera manually to suit a particular light
source.
Select “· Manual WB”.
Blank white
paper
1
2
Under the lighting conditions you plan to
use when shooting, point the camera at a
blank white piece of paper so it fills the
entire monitor screen and then press the
shutter button.
Manual WB
Press [SET].
3
The white balance setting is retained even if
you turn off the camera.
Download from Www.Somanuals.com. All Manuals Search And DownSlonaapds.hot Tutorial
40
• When “‡ Auto WB” is selected for the white balance setting, the camera
automatically determines the white point of the subject. Certain subject colors
and light source conditions can cause problems when the camera tries to
determine the white point, which makes proper white balance adjustment
impossible. If this happens, select the white balance setting that matches your
shooting conditions (Daylight, Overcast, etc.).
Correcting Image Brightness (EV Shift)
You can manually adjust an image’s exposure value (EV value) before shooting it.
• Exposure Compensation Range: –2.0 EV to +2.0 EV
• Unit: 1/3EV
1. In the REC mode, press [SET].
2. Use [8] and [2] to select the fifth control panel option from the top (EV
Shift).
3. Use [4] and [6] to adjust the exposure compensation value.
[6]: Increases the EV value. A higher EV
value is best for light-colored subjects
and backlit subjects.
[4]: Decreases the EV value. A lower EV
value is best for dark-color subjects and
for shooting outdoors on a clear day.
To cancel exposure compensation, change
the EV value to 0.0.
Exposure compensation value
4. Press [SET].
This applies the exposure compensation value. The exposure compensation
value you set remains in effect until you change it or turn off the camera (which
causes it to revert to “0.0”).
NOTE
• When shooting under very dark or very bright conditions, you may not be able to
obtain satisfactory results even after performing exposure compensation.
• EV shift is disabled while the “High Speed Lighting” BEST SHOT scene is being
use.
Download from Www.Somanuals.com. All Manuals Search And DownSlonaapds.hot Tutorial
41
Shooting with Slow Motion View
When you press [SLOW] (Slow Motion View), the
camera will start to pre-record images continually in
a buffer and play them back at slow speed. Up to
three seconds worth of pre-recorded images are in
the buffer. Fully pressing the shutter button will save
the currently displayed pre-recorded image. You
can specify one of eight playback speeds for pre-
recorded images.
[SLOW] (Slow Motion View)
. To get ready to shoot with Slow Motion View
1. In the REC mode, press [SET].
2. Use [8] and [2] to select the third control panel
option from the bottom (Slow Motion View).
3. Use [4] and [6] to select the Slow Motion View pre-record time (buffer
size).
You can select 1 second (30 fps), 2 seconds (15 fps), or 3 seconds (10 fps).
with the time (and CS fps) you specify here are displayed on the monitor screen
in slow motion.
. To shoot with Slow Motion View
1. Point the camera at the subject.
2. Press [SLOW] (Slow Motion View).
This will start slow motion playback of pre-recorded
images on the monitor screen.
• You can use [4] and [6] to change the playback
speed while Slow Motion View playback is in
progress. You can select one of eight speeds, from 1
to 8. A higher level number specifies a faster
Playback speed bar
playback speed.
Download from Www.Somanuals.com. All Manuals Search And DownSlonaapds.hot Tutorial
42
3. When the pre-recorded image you want to save is displayed, press the
shutter button.
This will store the displayed image as a snapshot and exit Show Motion View. To
exit Slow Motion View without saving any image, press [SLOW].
NOTE
• Press [SLOW] before the instance you want to shoot occurs.
• After pressing [SLOW], be sure to keep the camera pointed at the subject for at
least the duration that is specified by the Slow Motion View pre-record time (buffer
size) setting.
• After you press [SLOW], the slow motion image playback will continue on the
screen until you press the shutter button to store one of the images. To stop slow
motion playback without saving any one of the images, press [SLOW] again.
• Focus and exposure settings remain fixed at what they were when you pressed
[SLOW].
• For focusing during a Slow Motion View operation, it is recommended that you half-
press the shutter button to focus before you press [SLOW] (it is not necessary to
keep the shutter button half-pressed after focus is achieved), or that you change
the “Continuous AF” setting to “On”.
• When “On” is selected for the “Continuous AF” setting, it will take slightly longer for
slow motion playback of the pre-recorded images to start after you press [SLOW].
• If the camera’s image size setting is “10M”, “3:2”, or “16:9” when you shoot a Slow
Motion View image, the size of the resulting image will be “9M”.
• The shooting range of Slow Motion View is narrower than that of a Single Shot
mode image.
• Switching to Slow Motion View causes the flash setting to become ? (Flash Off)
automatically.
Download from Www.Somanuals.com. All Manuals Search And DownSlonaapds.hot Tutorial
43
Using Flash (Flash)
1. In the REC mode, press [2] (
)
Flash
once.
2. Use [4] and [6] to select the flash
setting you want and then press
[SET].
[2] (
)
Flash fires automatically in accordance with exposure
(amount of light and brightness) conditions.
>
?
Auto Flash
Flash Off
Flash does not fire.
Flash always fires. This setting can be used to brighten a
subject that normally comes out dark due to daylight or
backlight (daylight synchro flash).
<
Flash On
¥
Reduction
Red Eye
Flash fires automatically. This type of flash can be used to
reduce the chance of redness in the subject’s eyes.
3. Press the shutter button to shoot.
Back lamp
Flashes red while the flash is charging to indicate that image
recording is disabled.
• You will not be able to take another flash snapshot until the
lamp stops flashing red, which indicates that charging is
complete.
< indicates the flash will fire.
Download from Www.Somanuals.com. All Manuals Search And DownSlonaapds.hot Tutorial
44
NOTE
• Take care so your fingers and the strap do not block the flash.
• The desired effect may not be obtained when the subject is too far away or too
close.
condition, ambient temperature, etc.).
• Shooting with flash turned off when lighting is dim results in a slow shutter speed,
which can cause image blur due to camera movement. Under such conditions,
secure the camera with a tripod, etc.
• With red eye reduction, the flash is fired automatically in accordance with
exposure. It does not fire in areas where lighting is bright.
• The presence of outdoor sunlight, fluorescent lighting, or some other light source
can cause abnormal image colors.
• Select ? (Flash Off) for the flash setting when shooting in areas where flash
photography is prohibited.
• While A, S, or M is selected for the exposure mode, the flash will not fire if > (Auto
Flash) or ¥ (Red Eye Reduction) is selected as the flash mode. If you want the
flash to fire, select < (Flash On) as the flash mode.
Red-eye Reduction
Using the flash to shoot at night or in a dimly lit room can cause red spots inside the
eyes of people who are in the image. This is caused when the light from the flash
reflects off of the retina of the eye. When red-eye reduction is selected as the flash
mode, the camera fires a pre-flash to cause the irises in the eyes of any people in the
image to close, which reduces the chance of red eye.
Note the following important points when using red-eye reduction.
• Red-eye reduction does not work unless the people in the image are looking
directly at the camera (flash).
• Red-eye reduction may not work very well if the subjects are located far away from
the camera.
Other Useful Flash Features
Download from Www.Somanuals.com. All Manuals Search And DownSlonaapds.hot Tutorial
45
Changing the Control Panel Date/Time Style
1. In the REC mode, press [SET].
2. Use [8] and [2] to select the bottom control panel option (Date/Time).
You can use [4] and [6] to select date or time display.
NOTE
Day/Month.
• The time is displayed using 24-hour format.
Shooting with Zoom
Your camera provides you with 5X optical zoom (that changes the lens focal
distance), which can be used in combination with digital zoom (that digitally
processes the center portion of the image to enlarge it) for total zoom capabilities of
5X to 79.7X. The image deterioration point depends on the image size (page 48).
1. In the REC mode, slide the zoom controller to zoom.
Zoom controller
w Wide Angle
z Telephoto
w (Wide Angle) : Reduces the size of the subject and broadens the range
z (Telephoto) : Enlarges the subject and narrows the range
2. Press the shutter button to shoot the image.
Download from Www.Somanuals.com. All Manuals Search And DownSlonaapds.hot Tutorial
46
NOTE
• The higher the digital zoom factor, the coarser the recorded image. Note that the
camera also has a function that lets you record using digital zoom without image
deterioration (page 48).
• Use of a tripod is recommended to protect against image blur due to camera
movement when shooting with telephoto.
• Performing a zoom operation changes the lens aperture.
• Both optical zoom and digital zoom are disabled during high speed movie
recording.
• Zooming with digital zoom only is possible during recording an HD or STD movie.
However, can zoom with optical zoom before you press [0] to start HD or STD
movie recording.
Optical Zoom/Digital Zoom Switch Point
If you hold the zoom controller towards z (Telephoto), the zoom operation will stop
when the optical zoom factor reaches its maximum. Momentarily releasing the zoom
controller and then holding it again towards z (Telephoto) will switch to digital
zoom, which you can use to set an even higher zoom factor.
• If you do want to use digital zoom, change the “Digital Zoom” setting to “On” (page
96).
• During zoom, a zoom bar on the monitor screen shows the current zoom setting.
Image deterioration indicator
Focusing range
(Displayed for Auto Focus, Macro Focus, and Manual
Focus.)
* Products marketed in some geographic areas display
inches and feet.
Zoom bar
Download from Www.Somanuals.com. All Manuals Search And DownSlonaapds.hot Tutorial
47
Undeteriorated digital zoom
Undeteriorated image
quality range
Deteriorated image
quality range
5X to 28.5X
20X to 79.7X
Zoom pointer (Indicates current zoom.)
Deterioration point
1X
Optical/digital zoom switch point
* 5X optical zoom point
• The deterioration point depends on
the current image size setting (page
35). The smaller the image size
setting, the higher the zoom factor you
can use before reaching the image
deterioration point.
Image
Size
Maximum
Zoom Factor
Deterioration
Point
10M
3:2
20X
20X
5X
5X
16:9
9M
20X
5X
• Though digital zoom generally causes
a deterioration of image quality, some
digital zoom without image
20X
5X
7M
23.8X
31.7X
45.5X
79.7X
6X
deterioration is possible with image
sizes of “7M” and smaller. The range
in which you can use digital zoom
without image deterioration is
indicated on the display. The
4M
7.9X
11.4X
28.5X
2M
VGA
deterioration point depends on the
image size.
• When “HD/STD” is selected as the
movie mode, minimal deterioration up
to a zoom factor of 28.5X is possible
only for STD shooting.
• The zoom bar is not displayed while
movie recording is in progress.
Download from Www.Somanuals.com. All Manuals Search And DownSlonaapds.hot Tutorial
48
Using Continuous Shutter
Pressing Õ (Continuous Shutter) toggles
between the Continuous Shutter mode and the
Õ (Continuous Shutter)
Using Normal-speed Continuous Shutter
The number of consecutive images you can shoot is theoretically unlimited, as long
as there is memory available to store them. Also note that the maximum shooting
speed of Normal Speed CS is limited by the type of memory card you are using and
the camera setup.
1. In the REC mode, press [MENU].
2. Use [4] and [6] to select the “REC” tab.
3. Use [8] and [2] to select “CS” and then press [6].
4. Use [8] and [2] to select “Normal Speed CS”, and then press [SET].
5. Press Õ (Continuous Shutter).
Normal Speed CS icon
• This will display Z (Normal Speed CS) and
surround the monitor screen with a yellow frame.
If this does not happen, press Õ again.
6. Hold down the shutter button to shoot.
Images continue to be shot as long as you keep the
shutter button depressed and there is memory
available to store them. Releasing the shutter button
stops shooting.
Yellow frame
Download from Www.Somanuals.com. All Manuals Search And DownSlonaapds.hot Tutorial
49
IMPORTANT!
playback screen is not supported.
• You cannot specify the number of images shot per second (fps) with Normal Speed
CS.
• The number of images per second (fps) of Normal Speed CS varies slightly
depending on the type of memory card you are using and its current condition
(remaining capacity, fragmentation state, etc.).
• You cannot use Normal Speed CS in combination with Prerecord CS.
Using High Speed CS and Prerecord CS
With High Speed CS, you can configure the camera to shoot at a speed of 1, 3, 5, 10,
15, 30, or 40 images per second, as long as you keep the shutter button and there is
memory available to store the images. With Prerecord CS, half-pressing the shutter
button starts continual pre-recording of images to a temporary buffer. Then when you
press the shutter button the rest of the way down, the camera stores what is currently
in the buffer and starts real-time continuous shutter recording of new images. Real-
time recording continues until you release the shutter button or until a total of up to
30 images (buffer images plus new images) are recorded. You can configure
Prerecord CS to specify how many of the 30 images are recorded in the buffer and
how many are recorded after you fully press the shutter button. Use Prerecord CS
when you want to make sure you do not miss fast-moving action.
Shutter button half-press
Shutter button full-press
Shutter button release
Recorded images (up to 30 images)
Continuous recording of images until shutter
button released*
Pre-recorded images
* You can record up to 30 images (pre-recorded buffer images plus real-time images) for
each Prerecord CS operation.
Download from Www.Somanuals.com. All Manuals Search And DownSlonaapds.hot Tutorial
50
• You can specify 5, 10, 20, or 30 as the maximum number of shots for each
continuous shutter operation.
• You can specify anywhere from 0.75 seconds up to 30 seconds as the continuous
shutter shooting time, which is the amount of time of the pre-record buffer plus the
amount of time that continuous shutter recording is performed after the shutter
button is pressed all the way. The maximum shooting time depends on the
selected CS speed. You can select a CS speed in the range of 1 to 30 fps.
40 images per second
You can shoot up to 30 images in 0.75 seconds.
(40 fps)
One image per second
You can shoot up to 30 images over 30 seconds.
(1 fps)
• You can configure the mode so up to 25 images are pre-recorded to the buffer until
you fully press the shutter button.
• The minimum number of pre-recorded buffer images you can specify is three. Total
recording time depends on the current continuous shutter frames-per-second (fps)
setting.
• Specifying zero for the number of pre-recorded images disables Prerecord CS and
performs High Speed CS only (without pre-recording).
1. In the REC mode, press [MENU].
2. Use [4] and [6] to select the “REC” tab.
3. Use [8] and [2] to select “CS” and then press [6].
4. Use [8] and [2] to select “High Speed CS”, and then press [SET].
5. Press Õ (Continuous Shutter).
High Speed CS icon
• This will display Š (High Speed CS) and
surround the monitor screen with a yellow frame.
If this does not happen, press Õ again.
6. Press [SET].
7. Use [8] and [2] to select the fourth control
panel option from the bottom (High Speed CS
fps).
Yellow frame
Download from Www.Somanuals.com. All Manuals Search And DownSlonaapds.hot Tutorial
51
8. Use [4] and [6] to select the continuous shutter
CS speed
(CS) speed you want and then press [SET].
The camera determines the CS speed by determining the
AUTO
surrounding light level and automatically configuring a speed that
prevents underexposure.
Enables specification of the number of CS images recorded per
second.
1 to 40 fps
9. Use [8] and [2] to select the third control panel
option from the bottom (Max CS shots).
10. Use [4] and [6] to select the maximum number of shots for each
continuous shutter operation and then press [SET].
11. Use [8] and [2] to select the second control panel option from the
bottom (Prerecord CS shots).
12. Use [4] and [6] to specify how many of the 30 images and for how
long images should be pre-recorded in the buffer.
• Prerecord CS shooting is not performed when the number of buffer images and
the recording time are both zero.
Shutter button full-press
Number of pre-record
images and pre-record
time (Not displayed when
“AUTO” is selected for
“High Speed CS fps”.)
Number of remaining images
and remaining recording time
after the shutter button full-
press (Not displayed when
“AUTO” is selected for “High
Speed CS fps”.)
13. Press [SET].
• The approximate number of recordable CS images will appear on the monitor
screen.
Number of recordable CS images (If you are not performing
Prerecord CS, the allowable continuous shutter time also is displayed.)
Remaining snapshot memory capacity
Download from Www.Somanuals.com. All Manuals Search And DownSlonaapds.hot Tutorial
52
14. Half-press the shutter button.
This will cause the camera to start pre-recording images.
• The camera will not emit a shutter sound when you half-press the shutter
button while Prerecord CS is selected.
• If you release the half-pressed shutter button before pressing it the rest of the
way down, all of the pre-recorded images currently in the buffer will be deleted.
15. When you are ready to shoot, press the shutter button the rest of the
way down.
This will record the images in the pre-record buffer and start recording new
images in real-time. Images continue to be shot as long as you keep the shutter
button depressed.
16. Real-time shooting will stop when you release the shutter button or
after the maximum number of shots is reached.
NOTE
• Note the following when selecting a High Speed CS speed (fps) setting.
– Use a higher High Speed CS speed (fps) setting when shooting a fast-moving
subject.
– Use a slower High Speed CS speed (fps) setting when shooting a slower-moving
subject.
• Note the following when selecting a High Speed CS maximum number of shots
setting.
– The greater the number of shots, the longer it takes to save them after shooting
is complete.
• Note the following when specifying a Prerecord CS shots setting.
– A setting that results in a Prerecord CS operation that takes at least 0.3 seconds
is recommended because there is a minimal lag from about 0.1 seconds to 0.3
seconds between the point you decide to shoot and the point that the shutter
button is fully depressed.
Download from Www.Somanuals.com. All Manuals Search And DownSlonaapds.hot Tutorial
53
Specifying the Method for Saving Continuous Shutter Images
Use the procedure below to specify how images should be saved after a High Speed
CS operation.
1. In the REC mode, press [MENU].
2. Use [4] and [6] to select the “REC” tab.
3. Use [8] and [2] to select “Save CS Images”, and then press [6].
4. Use [8] and [2] to change the setting.
Normal (Batch)
All images that were shot are saved after the continuous shutter operation is
finished.
Download from Www.Somanuals.com. All Manuals Search And DownSlonaapds.hot Tutorial
54
Select & Save
After continuous shutter shooting is finished, the shot images are played back
at slow speed so you can select the images you want to save.
• When shooting with Prerecord CS, the first image saved when you press the
shutter all the way is indicated by an “S” mark so you can tell where the
continuous shutter operation started.
While the shot images are playing back and an image
appears that you want to save, press the shutter
button. Each image that you select by pressing the
shutter button will have a mark appended to it.
After selecting all of the images you want to save,
press [MENU].
Mark
1
2
Buttons Used for Image Selection
During playback, these buttons change the playback
direction and playback speed.
While playback is paused, these buttons scroll forward or
back.
[4] [6]
[SET]
Toggles between pause and play.
Shutter
button
Press all the way down to select an image for saving.
Saves the selected images and exits the image select
operation.
[MENU]
Use [8] and [2] to select the save method you want and then press [SET].
3
Save All
Save Selected : Saves selected images.
Back : Returns to image selection.
Cancel Save : Does not save any of the images.
: Saves all the images.
Always Ask
After continuous shutter shooting is finished, a prompt appears allowing you to
select Normal (Batch) or Select & Save.
Select the save method you want to use and then press [SET].
Save Selected : Saves selected images.
Save All
: Saves all the images.
Cancel Save : Does not save any of the images.
5. Press [SET] to apply the setting.
Download from Www.Somanuals.com. All Manuals Search And DownSlonaapds.hot Tutorial
55
Continuous Shutter Precautions
• If there is not enough available capacity on the memory card, you may not be able
to record the number of CS images indicated on the monitor screen. Make sure
your memory card has sufficient remaining capacity before shooting with using
continuous shutter.
• With continuous shutter, exposure and focus for the first image are applied for
successive images as well.
• When using a continuous shutter mode, keep the camera still until shooting is
finished.
• In the Continuous Shutter mode, the flash setting automatically becomes ?
(Flash Off).
• Zoom is disabled during continuous shutter operations.
• The following image sizes cannot be selected while shooting with High Speed CS:
“10M”, “3:2”, “16:9”. Entering the High Speed CS mode while any one of these
image sizes is selected will cause the image size setting to change to “9M”
automatically.
• The maximum number of images that can be recorded during each High Speed CS
session is limited, regardless of how much memory card storage capacity is
available.
Specified maximum number of continuous shutter shots
(Max CS shots)
Š
High Speed CS
The number of images will be restricted even further or shooting may be impossible
when remaining memory card capacity is less than the allowable number of images
for a particular CS mode.
• The Triple Self-time cannot be used in the High Speed CS mode.
• The Self-timer cannot be used in the Prerecord CS mode.
• When using Prerecord CS, if you release the half-pressed shutter button before
pressing it the rest of the way down, all of the pre-recorded images currently in the
buffer will be deleted.
Download from Www.Somanuals.com. All Manuals Search And DownSlonaapds.hot Tutorial
56
Recording Movies
To record a movie
The following procedure explains how to record a standard (STD) movie.
See the pages indicated below for more information about movies.
High-definition movie (HD movie): page 60
High speed movie (HS movie): page 60
[0] (Movie)
1. In the REC mode, set the movie
mode switch to ³ (HD/STD).
Movie mode
switch
2. Press [MENU].
3. Use [4] and [6] to select the “Quality” tab.
4. Use [8] and [2] to select “» Quality” and then press [6].
5. Use [8] and [2] to select “STD” (Standard),
and then press [SET].
• Recording is performed with an aspect ratio of
x
4:3, an image size of 640 480 pixels, and a
frame rate of 30 frames per second (STD Movie).
Image size setting cannot be changed.
• The semi-transparent gray frame on the monitor
Semi-transparent gray
frame
screen indicates the area that is recorded when
shooting a movie. The area within the frame is
recorded for a movie.
6. Press [0] (Movie).
Remaining recording time
(page 185)
This will start recording and display Y on the
monitor screen.
Movie recording includes monaural audio.
7. Press [0] again to stop recording.
• Each movie can be up to 10 minutes long. Movie
recording stops automatically after 10 minutes of
recording. Movie recording also will stop
automatically if memory becomes full before you
stop movie recording by pressing [0] again.
Recording time
Recording Movies
Download from Www.Somanuals.com. All Manuals Search And Download.
57
Shooting with BEST SHOT
of movie you are trying to shoot and the camera will change its setup accordingly, for
beautiful movies every time. Selecting the “Natural Green” BEST SHOT scene, for
example, will shot images with vivid green trees and grass.
Minimizing the Effects of Camera Movement during Movie Recording
You can configure the camera to minimize the effects of camera movement during
image blur due to subject movement.
Audio
Your camera has a built-in microphone that can be used to record audio (monaural)
during movie recording.
. Recording Precautions
The camera also records audio. Note the following points when
shooting a movie.
– Take care that the microphone is not blocked by your
fingers, etc.
– Good audio recording results are not possible when the
camera is too far away from what you are trying to record.
– Operating camera buttons while shooting can cause
button noise to be picked up in the audio.
Microphone
• When shooting with the “HS” movie mode at a frame rate
setting of “30-120 fps” or “30-240 fps”, audio is recorded only
while the camera is shooting at 30 fps. Audio is not recorded at any other frame
rates.
Recording Movies
Download from Www.Somanuals.com. All Manuals Search And Download.
58
NOTE
• Spending a long time using movie recording will cause the camera to become
slightly warm to the touch. This is normal and does not indicate malfunction.
• Use of certain types of memory cards slows down data transfer and increases the
time it takes to record movie data, which can result in movie frames being dropped.
The Y indicator on the monitor screen turns yellow to indicate that frames are
being dropped. In order to avoid problems such as these, use of an Ultra High
Speed Type SD memory card is recommended. Note, however that CASIO makes
no guarantees about the operation of any Ultra High Speed Type SD memory card
used with this camera.
• Only digital zoom is enabled during HD or STD movie recording. Zoom is disabled
during high speed movie recording. To use optical zoom for HD movie, STD movie,
or high speed movie recording, perform the zoom operation before you press [0] to
start recording.
• The zoom bar is not displayed while movie recording is in progress.
• The effects of camera movement in an image become more pronounced when you
shoot close up or with a large zoom factor. Because of this, use of a tripod is
recommended under these conditions.
• Face Detection is disabled during movie (HD, STD, high speed) recording.
• During movie (HD, STD, high speed) recording, focus is fixed at the position where
it was when recording started. To focus an image, half-press the shutter button for
Auto Focus or focus manually before you press [0] to start recording.
• With HD movie and STD movie recording, the exposure mode is always t (Auto),
regardless of the currently exposure mode (Auto, A, S, M, BS) setting.
• With high speed movie recording, the exposure is fixed at the value in effect when
recording was started. The exposure value that is applied is affected by selecting
the A, S, or M exposure mode, by the shutter speed, and by the ISO sensitivity (in
case of the M mode only). Note that the setting range of the shutter speed depends
on the current high speed movie recording speed (fps).
• When using the “Prerecord (Movie)” and “For YouTube” BEST SHOT scenes, the
exposure mode is always t (Auto). The A, S, and M exposure modes are
disabled.
• The following BEST SHOT scenes always shoot using high speed movie. The
current movie mode switch setting is ignored.
“Child High Speed Movie”, “Pet High Speed Movie”, “Sports High Speed Movie”
Recording Movies
Download from Www.Somanuals.com. All Manuals Search And Download.
59
Recording a High-definition Movie
This camera supports recording of high-definition (HD) movies. The aspect ratio of an
x
HD movie is 16:9, the image size is 1280 720 pixels, and the frame rate is 30 fps.
Image quality and image size settings cannot be changed.
1. In the REC mode, set the movie mode switch to ³ (HD/STD).
2. Press [MENU].
3. Use [4] and [6] to select the “Quality” tab.
4. Use [8] and [2] to select “» Quality” and then press [6].
5. Use [8] and [2] to select “HD”, and then press [SET].
6. Record the movie the same way as you would a normal movie (page
57).
Press [0] to start and stop recording.
Recording a High Speed Movie
This camera supports recording of high speed movies at a maximum speed of
1000 fps. The aspect ratio of movies recorded with this mode depends on the frame
rate (recording speed).
• When shooting with the “HS” movie mode at a frame rate setting of “30-120 fps” or
“30-240 fps”, audio is recorded only while the camera is shooting at 30 fps. Audio is
not recorded at any other frame rates.
1. In the REC mode, set the movie mode switch to © (HS).
2. Press [MENU].
3. Use [4] and [6] to select the “Quality” tab.
4. Use [8] and [2] to select “HS » Speed” and then press [6].
Recording Movies
Download from Www.Somanuals.com. All Manuals Search And Download.
60
5. Use [8] and [2] to select the frame rate (recording speed) you want
and then press [SET].
A fast frame rate (such as 1000 fps) will result in a smaller image size.
Frame Rate
120 fps
Image Size (Pixels)
x
640 480
x
448 336
240 fps
x
224 168
420 fps
* fps (frames per second) is
a unit of measurement
indicating the number of
images recorded or
x
224 64
1000 fps
30-120 fps
30-240 fps
x
640 480
x
448 336
played back per second.
6. Record the movie the same way as you would a normal movie (page
57).
Press [0] to start and stop recording.
• When “30-120 fps” or “30-240 fps” is selected as the frame rate, recording
always starts with a frame rate of 30 fps. You can switch the frame rate
between 30 fps and 120 fps or between 30 fps and 240 fps only while recording
is in progress. Audio is recorded only while shooting at a 30 fps. Use [4] and
[6] or press [SET] to switch speeds.
NOTE
• The higher the frame rate (speed), the more lighting is required when shooting.
When shooting a high speed movie, shoot in a well-lit environment.
• When recording certain types of movies, the image that appears on the monitor
screen may be smaller than normal. When recording a high speed movie, there are
black bands along the top, bottom, left, and right of the screen.
• When recording a high speed movie, light source flicker can cause horizontal
bands to appear in the image. This does not indicate malfunction of the camera.
• Monitor screen content switching is disabled during high speed movie recording.
Recording Movies
Download from Www.Somanuals.com. All Manuals Search And Download.
61
Using Prerecord Movie (Prerecord (Movie))
With this feature, the camera pre-records up to five seconds of whatever is happening
in front of the lens in a buffer that is continually updated. Pressing [0] saves the
pre-recorded action (buffer contents) followed by real-time recording. Real-time
recording continues until you stop it. Prerecord Movie can be used when shooting a
standard (STD) movie, a high-definition (HD) movie, or a high speed (HS) movie.
• When using Prerecord Movie in combination with high speed movie, the buffer will
store two seconds of pre-recording instead of the usual five.
[0]
[0]
Movie
Real-time recording start
Real-time recording end
5-second prerecorded part (from the buffer)
* Approximately two seconds for high speed movie
. To set up the camera to shoot with Prerecord Movie
1. In the REC mode, select the movie mode you want to use by setting the
movie mode switch to ³ (HD/STD) or © (HS).
2. Press [BS].
3. Use [8], [2], [4], and [6] to select the “Prerecord (Movie)” scene and
then press [SET].
This causes ‰ (Prerecord (Movie)) to appear on the monitor screen, indicating
that the camera is prerecording to its buffer.
Recording Movies
Download from Www.Somanuals.com. All Manuals Search And Download.
62
. To shoot a Prerecord Movie
1. After using the above procedure to set up the camera for Prerecord
Movie, point the camera at the subject.
2. When you are ready to record, press [0].
This will save the approximately five seconds of action that was prerecorded in
the buffer before you pressed [0] (two seconds if you are using high speed
movie) and start real-time recording.
3. Press [0] again to stop recording.
• To turn off Prerecord Movie, press [BS] and then select R (Auto).
• When shooting with the high speed movie “30-120 fps” and “30-240 fps”
setting, you cannot change the speed (fps) setting while the camera is pre-
recording to the buffer in step 1 of the above procedure. You can change the
speed (fps) setting after you press [0] to start real-time recording.
NOTE
• While the camera is set up for shooting with Prerecord Movie, pressing the shutter
button will not shoot a snapshot unless movie recording is in progress. With high-
definition (HD) and standard (STD) movie, you can shoot still images while realtime
movie recording is in progress.
Recording Movies
Download from Www.Somanuals.com. All Manuals Search And Download.
63
Recording a Movie for YouTube (For YouTube)
The “For YouTube” scene records movies in a format that is optimal for uploading to
the YouTube movie site, which is operated by YouTube, LLC. “For YouTube” can be
used when shooting a standard (STD) movie, a high-definition (HD) movie, or a high
speed (HS) movie.
1. In the REC mode, set the movie mode switch to ³ (HD/STD) or ©
(HS).
Select the movie mode you want to use.
2. Press [BS].
3. Use [8], [2], [4], and [6] to select the “For YouTube” scene and then
press [SET].
This causes Ê to appear on the monitor screen.
4. Record the movie.
The movie file will be stored in a camera folder named “100YOUTB”.
• Installing YouTube Uploader for CASIO from the CD-ROM that comes with
your camera simplifies uploading of movie files you recorded with the “For
• To exit “For YouTube”, press [BS] and then select R (Auto).
NOTE
• Movies recorded with the “For YouTube” scene are stored in a special folder to
shot using the image size, recording speed, and quality settings configured in the
Movie Mode (page 57).
• Snapshots cannot be shot (regardless of whether you are recording or not) while
the “For YouTube” scene is selected.
Recording Movies
Download from Www.Somanuals.com. All Manuals Search And Download.
64
Shooting a Snapshot while Shooting a Movie
1. While a movie is being recorded,
press the shutter button.
Movie recording continues after the
snapshot is recorded.
Number of recordable snapshots
NOTE
• You can shoot up to 10 snapshots per movie. The number of snapshots is also
limited by the amount of free space available on the memory card.
• Note that the flash cannot be used when shooting a Snapshot in Movie.
• A snapshot cannot be shot during recording of the following types of movies.
High speed movie, some BEST SHOT scenes (Child High Speed Movie, Pet High
Speed Movie, Sports High Speed Movie, For YouTube)
• You cannot use Snapshot in Movie to shoot a snapshot when recording with
“Prerecord (Movie)” while the movie is being pre-recorded to the buffer before you
press [0]. You will be able to shoot snapshots during real-time movie recording,
which starts when you press [0].
• The size of the snapshot is “2M” if any one of the following settings is selected as
the image size before movie recording is started: “10M”, “3:2”, “16:9”, “9M”, “7M”,
“4M”, “2M”. If “VGA” is selected as the image size, the size of the snapshot is
“VGA”.
• The shooting range when shooting a snapshot while movie recording is in progress
is narrower than that of the Single Shot Mode.
• Snapshots shot with Snapshot in Movie cannot be focused individually. The focus
will be the same as the movie being recorded.
Recording Movies
Download from Www.Somanuals.com. All Manuals Search And Download.
65
Using BEST SHOT
What is BEST SHOT?
BEST SHOT provides you with a collection of sample “scenes” that show a variety of
different types of shooting conditions. When you need to change the setup of the
camera, simply find the scene that matches what you are trying to achieve, and the
camera sets up for it automatically. This helps to minimize the chance of ruined
images due to poor exposure and shutter speed settings.
Some Sample Scenes
High Speed
High Speed
Night Scene
Portrait
Scenery
Night Scene and
Portrait
To shoot with BEST SHOT
1. In the REC mode, press [BS].
This will display a menu of BEST SHOT scenes.
• The initial default selection is “Expression CS”.
2. Use [8], [2], [4], and [6] to move the
boundary to the scene you want to select.
[BS]
• The scene menu has multiple pages. Use [8]
and [2] to scroll between menu pages.
• You can access information about the
currently selected scene. See page 67 for
details.
Currently selected scene
(with boundary)
• To return to normal snapshot recording, select
Scene 1 R (Auto). Pressing [MENU] while the
scene selection screen or scene information
screen is displayed will cause the boundary to
jump directly to R (Auto).
Scene name
Scene number
Download from Www.Somanuals.com. All Manuals Search And DowUnsloinagdB.EST SHOT
66
3. Press [SET] to configure the camera with the settings for the currently
selected scene.
This returns to the REC mode.
• The settings of the scene you selected remain in effect until you select a
different scene.
• To select a different BEST SHOT scene, repeat the above procedure from
step 1.
4. Press the shutter button (if you are shooting a snapshot) or [0] (if you
are shooting a movie).
. Using the Scene Information Screen
To find out more about a scene, select it with the boundary
on the scene menu and then slide the zoom controller in
either direction.
• To return to the scene menu, slide the zoom controller
again.
• To scroll between scenes, use [4] and [6].
• To configure the camera with the settings for the currently
selected scene, press [SET]. To return to the scene
information screen for the currently selected BEST SHOT scene, press [BS].
Download from Www.Somanuals.com. All Manuals Search And DowUnsloinagdB.EST SHOT
67
. BEST SHOT Precautions
• BEST SHOT scene images were not shot using this camera.
• Images shot using a BEST SHOT scene may not produce the results you expected
due to shooting conditions and other factors.
• You can modify the camera settings that are configured after you select a BEST
SHOT scene. Note, however, that the BEST SHOT settings revert to their defaults
when you select another BEST SHOT scene or turn off the camera.
• Snapshot shooting (including Slow Motion View) is disabled while the following
BEST SHOT scenes are being used.
“Child High Speed Movie”, “Pet High Speed Movie”, “Sports High Speed Movie”,
“Prerecord (Movie)”, “For YouTube”
• Movie recording is disabled while the following BEST SHOT scenes are being
used.
“Lag Correction”, “High Speed Lighting”, “High Speed Anti Shake”, “High Speed
Best Selection”, “Multi-motion Image”, “Move Out CS”, “Move In CS”
• HD movie and STD movie recording are disabled (and high speed movie is always
enabled) while the following BEST SHOT scenes are being used.
“Child High Speed Movie”, “Pet High Speed Movie”, “Sports High Speed Movie”
• Shooting with a BEST SHOT scene automatically shoots with the mode setting that
is configured for that scene, regardless of whether the camera’s current REC mode
setting is Single Shot or continuous shutter (CS) setting.
• The “10M”, “3:2”, “16:9” image sizes cannot be selected while shooting with some
BEST SHOT scenes*. Selecting some BEST SHOT scenes* while any one of
these image sizes is selected will cause the image size setting to change to “9M”
automatically.
* “High Speed Anti Shake”, “High Speed Night Scene”, “High Speed Night Scene
and Portrait”, “Move Out CS”, “Move In CS”, “Multi-motion Image”, “High Speed
Best Selection”, “Lag Correction”, “High Speed Lighting”, “Expression CS”,
“Baby CS”, “Child CS”, “Pet CS”, “Sports CS”
• When the movie mode is HD/STD, movies are recorded using the settings of the
selected BEST SHOT scene. For high speed movie recording, BEST SHOT scene
settings are ignored and movie recording is performed as it normally is.
Download from Www.Somanuals.com. All Manuals Search And DowUnsloinagdB.EST SHOT
68
Creating Your Own BEST SHOT Setups
You can save up to 999 camera setups as user BEST SHOT scenes for instant recall
whenever you need them.
1. On the BEST SHOT scene menu, select the scene named BEST SHOT
(Register User Scene).
2. Use [4] and [6] to select the snapshot whose setup you want to save.
3. Use [8] and [2] to select “Save”, and then press [SET].
Your BEST SHOT scene will be assigned the name “Recall User Scene”, along
with a scene number.
NOTE
• You can create BEST SHOT setup for snapshots only. You cannot create a movie
BEST SHOT setup.
• You can check the settings of the currently selected BEST SHOT scene by
displaying the camera’s setting menus and looking at its settings.
• User snapshot scenes are assigned numbers in the sequence: U1, U2, and so on.
• The following are the settings that are saved for each user snapshot BEST SHOT
scene.
Face Detection, Focus, EV Shift, White Balance, Flash, ISO, Metering, Lighting,
Flash Intensity, Color Filter, Sharpness, Saturation, Contrast
folder (snapshots).
scenes.
• Use the following procedure when you want to delete a user BEST SHOT scene.
want to delete.
1
Press [2] (
), select “Delete”, and then press [SET].
2
Download from Www.Somanuals.com. All Manuals Search And DowUnsloinagdB.EST SHOT
69
Shooting with High Speed Night Scene
(High Speed Night Scene/High Speed Night Scene and
Portrait)
With High Speed Night Scene and High Speed Night Scene and Portrait, the camera
detects automatically whether it is being hand-held or on a tripod. If the camera
detects it is being hand-held, pressing the shutter button will record a series of
images and combine them in a way that minimizes image blur due to low light
conditions. If the camera detects it is on a tripod, it will shoot a single image using a
longer exposure time (instead of shooting and combining multiple images), which
results in an even clearer image. The flash is always disabled while “High Speed
Night Scene” is selected. If the night scene image you are shooting includes people,
use the “High Speed Night Scene and Portrait” BEST SHOT scene. The flash mode
setting becomes > (Auto Flash) when shooting with “High Speed Night Scene and
Portrait”.
1. In the REC mode, press [BS].
2. Select “High Speed Night Scene” or “High Speed Night Scene and
Portrait” and then press [SET].
3. When you are ready to shoot, press the shutter button.
• After you press the shutter button, the message “Busy... Please wait...” will
appear on the monitor screen to indicate that recording is in progress. Keep the
camera still while this message is displayed. The recording process takes
some time to complete after the message appears.
NOTE
• When holding the camera by hand while shooting with these BEST SHOT scenes,
make sure that the subjects remain as still as possible as the camera shoots the
series of images.
• To cancel this BEST SHOT scene and enter the Continuous Shutter mode, press
Õ (Continuous Shutter).
• Shooting with this BEST SHOT scene makes the shooting range narrower than
normal.
• Movement while the camera is mounted on a tripod may cause the camera to
erroneously judge it is being hand held.
• For handheld shooting under very dark conditions, the “High Speed Night Scene”
or “High Speed Night Scene and Portrait” BEST SHOT scene may not be able to
produce the exposure level required for a clear image. Use of a tripod under very
dark conditions is recommended.
• When shooting with these BEST SHOT scenes, the “ISO Sensitivity” setting is fixed
at “AUTO”.
Download from Www.Somanuals.com. All Manuals Search And DowUnsloinagdB.EST SHOT
B
70
Shooting with High Speed Anti Shake
(High Speed Anti Shake)
When you press the shutter button while High Speed Anti Shake is enabled, the
camera records multiple images and automatically combines them in a way that
produces a final image with minimal blur. You can shoot with this feature to minimize
the effects of camera movement when shooting with optical anti shake does not
produce the desired results.
1. In the REC mode, press [BS].
2. Select “High Speed Anti Shake” and then press [SET].
3. When you are ready to shoot, press the shutter button.
• After you press the shutter button, the message “Busy... Please wait...” will
appear on the monitor screen to indicate that recording is in progress. Keep the
camera still while this message is displayed. The recording process takes
some time to complete after the message appears.
NOTE
• To cancel this BEST SHOT scene and enter the Continuous Shutter mode, press
Õ (Continuous Shutter).
• With this BEST SHOT scene, the flash setting automatically becomes ? (Flash
Off).
• Shooting with this BEST SHOT scene makes the shooting range narrower than
normal.
• High Speed Anti Shake will not operate correctly while the camera is mounted on a
tripod.
• High Speed Anti Shake may not operate properly resulting in blurred images if the
camera is moved more than the allowable range or if the subject moves during
shooting.
• When shooting with this BEST SHOT scene, the “ISO Sensitivity” setting is fixed at
“AUTO”.
Download from Www.Somanuals.com. All Manuals Search And DowUnsloinagdB.EST SHOT
71
Digitally Correcting for Overexposure and Underexposure
(High Speed Lighting)
This BEST SHOT scene shoots a series of CS images using different exposure
settings and combines them into a final image to correct for overexposure or
underexposure of subjects of differing brightness.
1. In the REC mode, press [BS].
2. Select “High Speed Lighting” and then press [SET].
3. Press the shutter button to shoot.
After you press the shutter button, the message “Busy... Please wait...” will
appear on the monitor screen to indicate that recording is in progress. Keep the
camera still while this message is displayed. The recording process takes some
time to complete after the message appears.
NOTE
?
• With this BEST SHOT scene, the flash setting automatically becomes
Off).
(Flash
• Shooting with this BEST SHOT scene makes the shooting range narrower than
normal.
• With this BEST SHOT scene, proper image combination will not be possible if a
subject is moving during shooting.
• When shooting with this BEST SHOT scene, you will not be able to change the EV
shift (exposure compensation) setting.
• Depending on shooting conditions and image composition, this BEST SHOT scene
may not be able to produce the desired result.
Download from Www.Somanuals.com. All Manuals Search And DowUnsloinagdB.EST SHOT
B
72
Configuring the Camera to Help You Better Time Your Shots
(Lag Correction)
There always is some unavoidable time lag between the point you press the shutter
button and the point that the image is actually recorded. The “Lag Correction” feature
lets you configure the camera to lessen or even eliminate this lag to help you better
time your shots and get exactly the moment you want. With “Lag Correction”, you
half-press the shutter button and compose the image you want to shoot. Then when
you full-press the shutter button, the camera pre-records a total of five images,
including four images of action that happened before you fully pressed the shutter
button. After that, you can view the images on the monitor screen and select the one
you want to keep.
1. In the REC mode, press [BS].
2. Select “Lag Correction” and then press [SET].
3. With the camera pointed at the subject, half-press and hold the shutter
button.
The camera will start pre-recording images at this time.
• If you release the half-pressed shutter button before pressing it the rest of the
way down, all of the pre-recorded images currently in the buffer will be deleted.
4. When you are ready to shoot, press the shutter button all the way
down.
After pre-recording is complete, one of the five images will appear on the monitor
screen for about three seconds.
5. If you want to view all five of the pre-recorded images, press [SET]
within about three seconds after a recorded image appears on the
monitor screen.
• If you do not press [SET] within three seconds, the image displayed in step 4
will be saved automatically as the final image.
Download from Www.Somanuals.com. All Manuals Search And DowUnsloinagdB.EST SHOT
73
6. Use [4] and [6] to scroll through the pre-recorded images on the
monitor screen.
Use [4] and [6] to scroll through the pre-recorded images. Each image appears,
along with an indication of the timing when it was pre-recorded.
–0.4 sec.
–0.3 sec.
–0.2 sec.
–0.1 sec.
SHUTTER
(Full-press)
(0.4*)
(0.3*)
(0.2*)
(0.1*)
* Seconds prior to full-press of shutter button.
• The timing of the image you select here will be the timing of the image
displayed first in step 4 the next time you perform the above procedure. If you
select the image that was pre-recorded 0.3 seconds prior to full-press of the
shutter button, for example, the –0.3-second image will be displayed in step 4
the next time you perform the above procedure.
7. To save the currently displayed image as the final images, press [SET].
NOTE
?
• With this BEST SHOT scene, the flash setting automatically becomes
Off).
(Flash
• Shooting with this BEST SHOT scene makes the shooting range narrower than
normal.
• The Self-timer cannot be used with this BEST SHOT scene.
• With this BEST SHOT scene, half-pressing the shutter button fixes focus and
exposure at their current levels.
• With this BEST SHOT scene, image recording will not be successful if you full-
press the shutter button without allowing enough time (at least 0.4 seconds) after
half-pressing it.
• Pay close attention to the subject when shooting. Failure to do so can cause
considerable lag from the instant you want to shoot until you actually full-press the
shutter button. This can cause image recording to be too late, even if you use this
function.
Immediately after you full-press the shutter button, one of the five pre-recorded
images will appear on the display as in step 4 of the above procedure.
Download from Www.Somanuals.com. All Manuals Search And DowUnsloinagdB.EST SHOT
74
Isolating Moving Subjects (Multi-motion image)
Multi-motion image can be used to isolate a moving subject
within a series of multiple images and place them against a
stationary background. Use a tripod or some other means
to make sure that the camera is not moving or shaking
when shooting with Multi-motion image.
Basic Multi-motion image Procedure
1. In the REC mode, press [BS].
2. Select “Multi-motion Image” and then press [SET].
3. Hold down the shutter button to record.
4. Release the shutter button.
Continuous Shutter shooting will stop and the resulting composite image will
appear on the monitor screen.
• The above procedure shoots multiple images and combines them
automatically into a final image. Do not move the camera until shooting is
complete.
• You can configure the maximum number of CS shots, the CS fps, and
Prerecord CS shots settings the same way as you configure the High Speed
for “Multi-motion Image” is 28 instead of 30.
NOTE
• To cancel this BEST SHOT scene and enter the Continuous Shutter mode, press
Õ (Continuous Shutter).
• With this BEST SHOT scene, the flash setting automatically becomes ? (Flash
Off).
• Shooting with this BEST SHOT scene makes the shooting range narrower than
normal.
• The Self-timer cannot be used with this BEST SHOT scene.
Download from Www.Somanuals.com. All Manuals Search And DowUnsloinagdB.EST SHOT
75
• Shooting with “Multi-motion Image” assumes that the subject is moving and
changing positions. Trying to use it to shoot a subject that is moving while
maintaining the same location (such as a golf swing, a baseball swing, etc.) will
cause an error message to appear on the monitor screen and failure of image
recording, or will produce an image in which the shots of the subject are arranged
incorrectly.
• Multi-motion will not operate correctly if you shake or move the camera along with
the movement of the subject.
• If an error message appears on the monitor screen, either secure the camera so it
does not move or shoot against a different type of background.
• If not enough CS images are recorded, an error will be displayed before the
camera starts to place the isolated subject onto the stationary background. This
can be caused if you release the shutter button too soon when recording the
moving subject. Keep the shutter button fully depressed long enough to allow
recording of more images.
• Choose a shooting angle so the colors, shapes, and patterns of the moving subject
and the background are as different as possible.
• Avoid a shooting angle where the background is monotone or mono-pattern (such
as a clear blue sky).
• The camera may not be able to compose the final image if the intervals between
movements are so narrow the subject shots overlap. If this happens, increase the
interval by using the control panel to select a slower “High Speed CS fps” setting
Download from Www.Somanuals.com. All Manuals Search And DowUnsloinagdB.EST SHOT
76
Shooting with Priority on Subject Faces
(High Speed Best Selection)
With High Speed Best Selection, the camera automatically shoots a series of images,
and selects the best one based on facial image blur, and facial expression (whether
the subject is smiling or blinking).
1. In the REC mode, press [BS].
2. Select “High Speed Best Selection” and then press [SET].
3. Press the shutter button to shoot.
• This will cause the message “Busy... Please wait...” to appear. Do not move
the camera while this message is displayed. The recording process takes
some time to complete after the message appears.
NOTE
• To cancel this BEST SHOT scene and enter the Continuous Shutter mode, press
Õ (Continuous Shutter).
• With this BEST SHOT scene, the flash setting automatically becomes ? (Flash
Off).
• Shooting with this BEST SHOT scene makes the shooting range narrower than
normal.
• If one or more of the faces are blurred in all of the images that are shot, they will be
blurred in the final image as well.
• The following conditions may make it impossible for the camera to determine if the
subject is blinking or smiling. This may result in a final image in which the subject is
blinking or not smiling.
– Faces that are partially or completely darkened by shadows, etc.
– Hair that is hiding or near the eyes
– Eye glasses
– Small faces
– Faces that are not looking directly at the camera
• Shooting a large group of people will cause processing of the image after shooting
to take longer.
Download from Www.Somanuals.com. All Manuals Search And DowUnsloinagdB.EST SHOT
77
Shooting an Image in Accordance with Subject Movement
(Move Out CS/Move In CS)
You can use these features to shoot an image automatically whenever the subject
moves into or moves out of a frame on the monitor screen. You also can configure the
camera to record images of what happened immediately before and after the subject
moves.
Automatically records what happened immediately before and
Move Out CS
Move In CS
after the subject moves outside of a boundary on the monitor
screen.
Automatically records what happened immediately before and
after the subject moves into a boundary on the monitor screen.
. To setup the camera
1. In the REC mode, press [BS].
2. Select “Move Out CS” or “Move In CS” and then press [SET].
3. Press [SET].
4. Configure the boundary location and size
settings.
[8] [2] [4] [6] Moves the boundary.
Zoom controller Resizes the boundary.
5. Press [SET].
Boundary
• If you want to reconfigure the settings, start again
from step 3.
6. Press [2].
7. Use [8] and [2] to select the fourth control panel option from the
bottom (High Speed CS fps).
Download from Www.Somanuals.com. All Manuals Search And DowUnsloinagdB.EST SHOT
78
8. Use [4] and [6] to select the continuous shutter
CS speed
(CS) speed you want and then press [SET].
The camera measures light levels and configures the fastest
possible CS speed setting automatically.
AUTO
Enables specification of the number of CS images recorded per
second.
1 to 40 fps
9. Use [8] and [2] to select the third control panel
option from the bottom (Max CS shots).
10. Use [4] and [6] to select the maximum number of shots for each
continuous shutter operation and then press [SET].
11. Use [8] and [2] to select the second control panel option from the
bottom (Prerecord CS shots).
12. Use [4] and [6] to specify how many of the 30 images and for how
long images should be pre-recorded in the buffer.
• You cannot set a value of “0” for the number of Prerecord CS buffer images.
Shutter button full-press
Number of pre-record
images and pre-record time
(Not displayed when “AUTO”
is selected for “High Speed
CS fps”.)
Number of remaining images
and remaining recording
time after the shutter button
full-press (Not displayed
when “AUTO” is selected for
“High Speed CS fps”.)
13. Press [SET].
Number of recordable
CS images
• The approximate number of recordable CS
images will appear on the monitor screen.
Remaining snapshot
memory capacity
Download from Www.Somanuals.com. All Manuals Search And DowUnsloinagdB.EST SHOT
79
14. Use [8] and [2] to select the bottom control panel option (Trigger
Sense).
15. Use [4] and [6] to select the subject movement sensitivity, and then
press [SET].
• You can select any one of three sensitivity levels: “High”, “Normal”, or “Low”.
• Move Out CS Setting Guide
High : For a subject that moves out of the boundary quickly
Low : For a subject that moves out of the boundary slowly
• Move In CS Setting Guide
High : For a subject that moves into the boundary quickly or for a small subject
(relative to the boundary)
Low : For a subject that moves into the boundary slowly or for a large subject
(relative to the boundary)
. To shoot using Move Out CS
1. Compose the image so the subject is within the boundary on the
monitor screen.
2. Half-press the shutter button.
• The camera will adjust exposure and focus automatically.
3. When the boundary on the monitor screen turns
green, press the shutter button the rest of the
way down.
At this time the camera will go into recording standby
and start pre-recording images and storing them in a
buffer, in accordance with the Prerecord CS shots
setting you configured in step 12 under “To setup the
while older images are continually being deleted.
The camera will start saving images automatically the moment it detects that the
subject has moved out of the boundary.
• “0 AUTO” flashes on the monitor screen during recording standby and auto
recording.
Download from Www.Somanuals.com. All Manuals Search And DowUnsloinagdB.EST SHOT
80
4. Image recording will continue until the end of the recording time is
reached.
• While the camera is in Move Out CS recording standby, you can cancel
standby by pressing the shutter button all the way down. You then will be able
to shoot images normally.
• To stop an ongoing real-time recording operation, press [SET].
. To shoot using Move In CS
1. Compose the image at a location where you expect the subject to enter
the boundary on the monitor screen.
2. Half-press the shutter button.
• The camera will adjust exposure and focus automatically.
recommended.
3. When the boundary on the monitor screen turns
green, press the shutter button the rest of the
way down.
At this time the camera will go into recording standby
and start pre-recording images and storing them in a
buffer, in accordance with the Prerecord CS shots
setting you configured in step 12 under “To setup the
Boundary
images keep being added while older images are
continually being deleted.
The camera will start saving images to memory automatically the moment it
detects the subject has moved into the area within the boundary.
• “0 AUTO” flashes on the monitor screen during recording standby and auto
recording.
4. Image recording will continue until the end of the recording time is
reached.
• While the camera is in Move In CS recording standby, you can cancel standby
by pressing the shutter button all the way down. You then will be able to shoot
images normally.
• To stop an ongoing real-time recording operation, press [SET].
Download from Www.Somanuals.com. All Manuals Search And DowUnsloinagdB.EST SHOT
81
NOTE
• To cancel this BEST SHOT scene and enter the Continuous Shutter mode, press
Õ (Continuous Shutter).
• With this BEST SHOT scene, the flash setting automatically becomes ? (Flash
Off).
• Shooting with this BEST SHOT scene makes the shooting range narrower than
normal.
• The Self-timer cannot be used with this BEST SHOT scene.
• Compose the image so the entire subject and its background are within the
boundary. Recording may not be performed correctly if there is little difference
between the subject and the part of the background enclosed by the boundary.
Also, Move Out CS may not record correctly if the subject is not in the center of the
boundary.
• Move In CS and Move Out CS do not operate correctly if you press the shutter
button all the way down. Be sure to half-press the shutter button. After images are
pre-recorded, press the shutter button the rest of the way down.
• After pressing the shutter button all the way to put the camera into record standby,
keep the camera still. Recording may not be performed correctly if you move the
camera during record standby.
• The sleep mode and Auto Power Off are disabled while the camera is in record
standby.
• The camera may not start recording automatically or camera power may turn off
when battery power is low. Always make sure that the battery is sufficiently
charged before using these features.
continuous shutter image save method. If you do, make sure that the memory card
loaded in the camera has enough free space to store them.
• Zoom is disabled, and focus and exposure are fixed while the camera is in
recording standby.
Download from Www.Somanuals.com. All Manuals Search And DowUnsloinagdB.EST SHOT
82
Using the Situation-specific CS Scenes
The High Speed CS capabilities provide you with a variety of BEST SHOT options to
suite exactly the type of image you are trying to record. Images continue to be shot as
long as you keep the shutter button depressed, with the shooting speed optimized
according to the BEST SHOT scene you are using.
Then when you press the shutter button the rest of the way down, the camera stores
what is currently in the buffer and starts real-time continuous shutter shooting of new
images. Shooting continues until you release the shutter button or until a total of up to
30 images (buffer images plus new images) are shot. Some of the 30 images are of
action that occurred before you full-pressed the shutter button and some are after.
This helps to ensure you capture exactly the moment you want, even if your timing is
slightly off.
Shutter button release
Shutter button full-press
Shutter button half-press
Recorded images (up to 30 images)
Continuous recording of images until
shutter button released*
Pre-recorded images
* You can record up to 30 images (pre-recorded buffer images plus real-time images) for
each Prerecord CS operation.
1. In the REC mode, press [BS].
2. Select the BEST SHOT scene you want to use and then press [SET].
The following are the settings for each BEST SHOT scene.
Scene Name
Expression CS
Baby CS
CS fps
3 fps
Maximum CS Shots Pre-recorded Shots
10 (3.3 seconds)
10 (2 seconds)
20 (2 seconds)
30 (2 seconds)
30 (1 second)
3 (1 second)
3 (0.6 seconds)
5 (0.5 seconds)
5 (0.3 seconds)
10 (0.3 seconds)
5 fps
Child CS
10 fps
15 fps
30 fps
Pet CS
Sports CS
Selecting one of these BEST SHOT scenes will enable High Speed CS as the
initial default. Though you could change the CS setting to Normal Speed CS, it
is recommended that you leave it set as High Speed CS.
Download from Www.Somanuals.com. All Manuals Search And DowUnsloinagdB.EST SHOT
83
3. Half-press and hold the shutter button to start pre-recording of images.
A preset number of images are pre-recorded. The pre-recorded images are
continually updated until you full-press the shutter button.
• If you release the half-pressed shutter button before pressing it the rest of the
way down, all of the pre-recorded images currently in the buffer will be deleted.
• The camera will not emit shutter sounds as it pre-records images.
4. Press the shutter button the rest of the way down.
This will save the pre-recorded images and start shooting new images in real-
time. Images continue to be shot as long as you keep the shutter button
depressed.
5. Shooting will stop when you release the shutter button or after the
maximum number of shots is reached.
NOTE
• CS settings (“High Speed CS” and “Normal Speed CS”) are enabled when shooting
with these BEST SHOT scenes. Precautions and control panel operations are the
• When using High Speed CS, Prerecord CS (pre-recording of images before the
shutter button is full-pressed) is not performed if you full-press the shutter button
without half-pressing first. Whenever possible, be sure to half-press the shutter
button, compose the image, and then full-press the shutter button.
Download from Www.Somanuals.com. All Manuals Search And DowUnsloinagdB.EST SHOT
84
Using the Situation-specific High Speed Movie Scenes
The High Speed Movie capabilities of the camera provide you with a variety of BEST
SHOT options to suite exactly the type of image you are trying to record.
1. In the REC mode, press [BS].
2. Select the BEST SHOT scene you want to use and then press [SET].
Scene Name
Frame Rate
120 fps
Child High Speed Movie
Pet High Speed Movie
Sports High Speed Movie
240 fps
420 fps
3. Record the movie the same way as you would a normal movie (page
57).
Press [0] to start and stop recording.
• When “30-120 fps” or “30-240 fps” is selected as the frame rate, recording
always starts with a frame rate of 30 fps. You can switch the frame rate
between 30 fps and 120 fps or between 30 fps and 240 fps only while recording
is in progress. Audio is recorded only while shooting at a 30 fps. Use [4] and
[6] or press [SET] to switch speeds.
NOTE
• These BEST SHOT scenes always shoot using high speed movie. The current
movie mode switch setting is ignored.
• Precautions and the shooting procedure are the same as those for High Speed
– A, S, M exposure mode settings
– Prerecord Movie
– YouTube movie recording
Download from Www.Somanuals.com. All Manuals Search And DowUnsloinagdB.EST SHOT
85
Advanced Settings
The following are menu operations you can use to configure various camera settings.
Using On-screen Menus
. Example Menu Screen Operation
Press [MENU] to display the menu screen.
• Menu contents are different in the REC mode and PLAY mode.
Example: REC mode menu
[8] [2] [4] [6]
[MENU]
[SET]
Menu Screen Operation Buttons
Selects tabs. [6] is also used to display the options available for a
setting.
[4] [6]
[8] [2]
[SET]
Selects a setting option.
Registers the selected setting.
Exits the menu screen.
[MENU]
1. In the REC mode, press [MENU].
This will display the menu screen.
2. Use [4] and [6] to select the tab where the item you want to configure
is located.
Advanced Settings
Download from Www.Somanuals.com. All Manuals Search And Download.
86
3. Use [8] and [2] to select the menu item you
want, and then press [6].
Example:
When “Self-timer” is
selected on the “REC” tab
4. Use [8] and [2] to change the setting.
Tabs
5. After the setting is the way you want, press
[SET].
• Pressing [4] registers the selected setting and
returns to the menu.
• To configure settings on another tab after
pressing [4] to return to the menu, use [8] to
move the highlighting up to the tabs, and then
use [4] and [6] to select the tab you want.
Items
. Menu Operations in This Manual
Menu operations are represented in this manual as shown below. The following
operation is the same as the one described under “Example Menu Screen Operation”
on page 86.
Use [4] and [6] to select the “REC” tab.
Procedure
[r] (REC) * [MENU] * REC Tab * Self-timer
Press
[r] (REC).
Press
[MENU].
Use [8] and [2] to select “Self-timer” and
then press [6].
Advanced Settings
Download from Www.Somanuals.com. All Manuals Search And Download.
87
REC Mode Settings (REC)
Selecting a Focus Mode (Focus)
Procedure
[r] (REC) * [MENU] * REC Tab * Focus
Focus Mode
Settings Type of Shot
Approximate Focus Range*1
Snapshot Movies
Snapshot
Movies
Approximately
3 cm to 9 (infinity)
(1.2" to 9)
Q Auto General
Automatic
Automatic
Focus
recording
Fixed
focal
point
Approximately
3 cm to 50 cm
(1.2" to 19.7")
Fixed
´
Macro
Close ups
distance
2
*
Shooting with a
relatively wide
focus range
EPan
Focus
Fixed
focal point
Fixed distance*2
Scenery and
other distant
subjects
)
Infinity
Fixed
Infinity
W
Manual
Focus
When you want
to focus
manually
Approximately 3 cm to
9 (infinity)*2 (1.2" to 9)
Manual
*1 The focus range is the distance from the lens surface.
*2 The focus range depends on the current optical zoom position.
Advanced Settings
Download from Www.Somanuals.com. All Manuals Search And Download.
88
To focus with manual focus
1. On the monitor screen, compose the image so
the subject you want to focus on is within the
yellow boundary.
2. Watching the image on the monitor screen use
[4] and [6] to adjust focus.
• At this time the image that is within the boundary
will enlarge and fill the monitor screen, which aids
in focusing. If you do not perform any operation for
two seconds while the enlarged image is displayed,
the screen in step 1 will re-appear.
Yellow boundary
NOTE
• An Auto Macro feature detects how far the subject is from the lens and
automatically selects either Macro Focus or Auto Focus accordingly.
• Use of the flash together with Macro Focus can cause the light of the flash to
become blocked, which may result in unwanted lens shadows in your image.
• In the case of movie recording, Auto Macro operates before you start recording.
After recording is started, however, focus is fixed.
• Whenever you perform an optical zoom operation while shooting with Auto Focus,
Macro Focus, or Manual Focus, a value will appear on the monitor screen to tell
you the focus range, as shown below. Note that the focus range is displayed
including the Auto Macro range only when shooting with Auto Focus.
Example: oo cm to 9
* oo is the actual focusing range value.
• The operations assigned to the [4] and [6] keys with the “L/R Key” setting (page
97) are disabled while Manual Focus is selected as the focus mode.
• Turning on “Face Detection” causes the focus mode to change automatically to Q
(Auto Focus). Changing the focus mode setting to anything other than Q (Auto
Focus) causes “Face Detection” to turn off automatically.
Advanced Settings
Download from Www.Somanuals.com. All Manuals Search And Download.
B
89
Using Focus Lock
Subject to be focused on
“Focus lock” is a technique you can use when you want to
compose an image in which the subject you want to focus
on is not within the focus frame in the center of the
screen.
• To use focus lock, select “U Spot” or “O Tracking” for
1. Align the monitor screen’s focus frame with
the subject you want to focus on and then half-
press the shutter button.
Focus frame
2. Keeping the shutter button half-pressed
(which maintains the focus setting), move the
camera to compose the image.
• When “O Tracking” is selected as the Auto Focus
area, the focus frame will move automatically and
follow the subject.
3. When you are ready to shoot the image, press the shutter button the
rest of the way down.
NOTE
• Focus lock also locks exposure (AE).
Advanced Settings
Download from Www.Somanuals.com. All Manuals Search And Download.
90
Using the Self-timer (Self-timer)
Procedure
[r] (REC) *[MENU] * REC Tab * Self-timer
With the Self-timer, pressing the shutter button starts a timer. The shutter is released
and the image is shot after a fixed amount of time.
„
10 sec 10-second Self-timer
2-second Self-timer
• When shooting under conditions that slow down the shutter speed,
you can use this setting to prevent image blur due to camera
movement.
‚
2 sec
Shoots three images: one image 10 seconds after the shutter button
is pressed, and the next two images as soon as the camera is ready
after shooting the previous image. How long it takes for the camera to
get ready to shoot depends on the image size and quality settings,
whether or not a memory card is loaded in the camera, and the flash
charge condition.
”
(Triple
Self-timer)
X3
Off
Self-timer is disabled.
• The front lamp flashes while the Self-timer countdown is in
Front lamp
progress.
• You can interrupt an ongoing Self-timer countdown by
pressing [SET].
NOTE
• The Self-timer cannot be used together with the following features.
High Speed CS with Prerecord CS, Slow Motion View, some BEST SHOT scenes
(Prerecord (Movie), Move Out CS, Move In CS, Multi-motion Image, Lag
Correction)
• The Triple Self-timer cannot be used together with the following features.
High Speed CS, Normal Speed CS, Movie, some BEST SHOT scenes (Expression
CS, Baby CS, Child CS, Pet CS, Sports CS, High Speed Best Selection, For
YouTube)
Advanced Settings
Download from Www.Somanuals.com. All Manuals Search And Download.
91
Reducing the Effects of Camera and Subject Movement
(Anti Shake)
Procedure
[r] (REC) * [MENU] * REC Tab * Anti Shake
You can turn on the camera’s Anti Shake feature to reduce image blur due to subject
movement or camera movement when shooting a moving subject using telephoto,
when shooting a fast-moving subject, or when shooting under dim lighting conditions.
D
A
S
Auto
Minimizes the effects of camera and subject movement
Minimizes the effects of camera movement only
Minimizes the effects of subject movement only
Camera AS
Image AS
A
Half-pressing the shutter button demonstrates the effect of “
Camera AS”. However, the image is not recorded.
F
DEMO
Off
Turns off all Anti Shake settings
NOTE
A
• “
Camera AS” only can be selected while recording with High Definition (HD)
and Standard (STD) movie.
• “S Image AS” is disabled while “S” or “M” is selected as the exposure mode.
• Anti Shake is not supported while recording with High Speed Movie.
• Shooting while “D Auto” or “S Image AS” is selected can cause an image to
appear somewhat coarser than normal and can cause slight deterioration of image
resolution.
• Anti Shake may not be able to eliminate the effects of camera or subject movement
when movement is severe.
A
• “
Camera AS” may not work properly when the camera is mounted on a tripod.
Either turn off Anti Shake or select “S Image AS”.
Advanced Settings
Download from Www.Somanuals.com. All Manuals Search And Download.
92
Specifying the Auto Focus Area (AF Area)
Procedure
[r] (REC) * [MENU] * REC Tab * AF Area
You can use the following procedure to change the Auto Focus metering area for
shooting snapshots.
U
• When recording movies, the AF metering area is always “
Spot”.
This mode takes readings of a small area in the center of the image.
U
Spot
Free
You can move the focus frame by using [8], [2], [4], and [6] to move
the focus point and then pressing [SET]. To change the focus point
position, select “— Free” again and then use [8], [2], [4] and [6] to
select the position you want.
—
O
When you half-press the shutter button while this setting is selected, the
Tracking focus frame will follow the movement of the subject.
U
“
O
Spot” or “
Tracking”
Focus frame
“— Free”
*
[SET]
Focus frame
Focus point
O
• “
Tracking” cannot be used in combination with the following features.
Prerecord CS, some BEST SHOT scenes (Move Out CS, Move In CS, Multi-motion
Image, Lag Correction, Expression CS, Baby CS, Child CS, Pet CS, Sports CS)
• “— Free” cannot be selected for the AF area while Face Detection is enabled.
Advanced Settings
Download from Www.Somanuals.com. All Manuals Search And Download.
93
Using the Auto Focus Assist Light (AF Assist Light)
Procedure
[r] (REC) * [MENU] * REC Tab * AF Assist Light
Half-pressing the shutter button while this setting is selected
causes the front lamp to light, which provides illumination for
focusing in areas where lighting is dim. Leaving this function
turned off is recommended when shooting portraits from short
distances, etc.
Front lamp
IMPORTANT!
• Never look directly into the front lamp while it is lit.
• Make sure your finger is not covering the front lamp.
Shooting with Face Detection (Face Detection)
Procedure
[r] (REC) * [MENU] * REC Tab * Face Detection
When shooting people, the face detection feature detects the faces of up to ten
individuals and adjusts focus and brightness accordingly.
1. Use [4] and [6] to select “On” and then press [SET].
2. Point the camera at the subject(s).
The camera will detect human faces and display a
frame around each one.
3. Half-press the shutter button.
The camera will focus and the frames around the
faces it focuses on will turn green.
Face Detection icon
4. Press the shutter button the rest of the way
down.
Advanced Settings
Download from Www.Somanuals.com. All Manuals Search And Download.
94
Tips for Best Face Detection Results
• The camera performs center focus if it cannot detect a face.
• Always make sure that Auto Focus (AF) is selected as the focus mode when
shooting with face detection.
• Detection of the following types of faces is not supported.
– A face that is obstructed by hair, sunglasses, a hat, etc., or a face in dark shade
– A profile or a face that is at an angle
– A face that is very far away and small, or very close and large
– A face in an area that is very dark
– A face of a pet or some other non-human subject
IMPORTANT!
• Face detection cannot be used in combination with any of the following features.
– Some BEST SHOT scenes (Move Out CS, Move In CS, Multi-motion Image, For
YouTube, Prerecord (Movie), Lag Correction)
– Movie Mode (Including some BEST SHOT scenes that support High Speed
Movie recording)
– High Speed CS with Prerecord CS (Including some BEST SHOT scenes that
support High Speed CS recording)
• Changing the focus mode setting to anything other than Q (Auto Focus) while
“Face Detection” is turned on causes “Face Detection” to turn off automatically.
Shooting with Continuous Auto Focus (Continuous AF)
Procedure
[r] (REC) * [MENU] * REC Tab * Continuous AF
When shooting a snapshot while “On” is selected for Continuous AF, Auto Focus is
performed and focusing is continually updated until you half-press the shutter button.
• Before you half-press the shutter button, the camera focuses at the center of the
press the shutter button, focusing is performed for the area specified by “— Free”.
If “Face Detection” is turned on, focusing is performed in the area where a face is
detected.
Advanced Settings
Download from Www.Somanuals.com. All Manuals Search And Download.
95
Changing the Continuous Shutter Mode (CS)
Procedure
[r] (REC) * [MENU] * REC Tab * CS
Perform the following steps to change the continuous shutter mode.
Š
High Speed CS
Enables shooting of up to 30 continuous shutter images at faster speeds than
Z
Normal Speed CS
The number of consecutive images you can shoot is theoretically unlimited, as
long as there is memory available to store them. Also note that the maximum
shooting speed of Normal Speed CS is limited by the type of memory card you
Configuring the Continuous Shutter Image Save Method
(Save CS Images)
Procedure
[r] (REC) * [MENU] * REC Tab * Save CS Images
Turning Digital Zoom On or Off (Digital Zoom)
Procedure
[r] (REC) * [MENU] * REC Tab * Digital Zoom
• Digital zoom is disabled while shooting with the following feature.
– High speed movie recording
Advanced Settings
Download from Www.Somanuals.com. All Manuals Search And Download.
96
Assigning Functions to the [4] and [6] Keys (L/R Key)
Procedure
[r] (REC) * [MENU] * REC Tab * L/R Key
You can assign one of the four functions listed below to the [4] and [6] keys.
Setting
[4]/[6] key operation
Selecting a Focus Mode (page 88)
• W (Manual Focus) and E (Pan Focus) cannot be
selected.
Q*´*)
Metering
Self-timer
Face Detection
Off
Changes the Metering Mode (page 101)
Sets the self-timer time (page 91)
Cancels [4] and [6] key assignments
Shooting with Quick Shutter (Quick Shutter)
Procedure
[r] (REC) * [MENU] * REC Tab * Quick Shutter
When Quick Shutter is turned on, you can press the shutter button all the way without
waiting for Auto Focus. This will record the image using a high speed focus operation
that is much faster than Auto Focus.
Turns on Quick Shutter
• Some images may be out of focus when Quick Shutter is used.
On
Turns off Quick Shutter so focus is performed using normal Auto Focus
before the image is recorded.
• If you fully press the shutter button while Quick Shutter is turned off,
images will continue to be shot without focusing.
Off
• Whenever possible, take a little extra time to half-press the shutter
button in order to ensure proper focus.
NOTE
• Quick Shutter is disabled when the zoom factor is greater. Recording is performed
using Auto Focus at this time.
Advanced Settings
Download from Www.Somanuals.com. All Manuals Search And Download.
97
Displaying the On-screen Grid (Grid)
Procedure
[r] (REC) * [MENU] * REC Tab * Grid
The on-screen grid can be displayed on the REC mode
monitor screen for easy vertical and horizontal alignment
when composing images.
Turning on Image Review (Review)
Procedure
[r] (REC) * [MENU] * REC Tab * Review
While Review is turned on, the camera will display a image for about one second
immediately after you press the shutter button to record it.
• Image review is available only when shooting single images. It does not work with
continuous shutter.
Using Icon Help (Icon Help)
Procedure
[r] (REC) * [MENU] * REC Tab * Icon Help
While Icon Help is turned on, a textual description will appear on the display for
certain icons when you switch between REC functions.
Functions Supported by Icon Help
• REC mode
• Available options for the “L/R Key” setting
• Exposure warning when shutter button is half-pressed
Advanced Settings
Download from Www.Somanuals.com. All Manuals Search And Download.
98
Configuring Power On Default Settings (Memory)
Procedure
[r] (REC) * [MENU] * REC Tab * Memory
This setting lets you specify which camera settings should be remembered by the
camera when it is turned off, and restored the next time the camera is turned on. To
have the camera remember a setting, you should enable the setting’s memory. Any
setting whose memory is disabled will be reset to its initial default any time the
camera is turned off.
Setting
Disabled (Initial Default Setting)
Enabled
Flash
Auto
Focus
Q(Auto Focus)
AF Area
Spot
Metering
CS
Multi
High Speed CS
Setting at
power off
Self-timer
Flash Intensity
Digital Zoom
MF Position
Zoom Position*
Off
0
On
Position before manual focus was selected.
Full wide
* Optical zoom setting only.
Advanced Settings
Download from Www.Somanuals.com. All Manuals Search And Download.
99
Image Quality Settings (Quality)
Specifying Snapshot Image Quality (T Quality (Snapshot))
Procedure
[r] (REC) * [MENU] * Quality Tab * T Quality (Snapshot)
Fine
Gives image quality priority
Normal
Normal
Economy
Gives the number of images priority
• The “Fine” setting helps to bring out details when shooting dense tree branches or
leaves, a complex pattern, etc.
• Memory capacity (the number of images you can record) will be affected by the
quality settings you configure (page 184).
Movie Image Quality Settings (» Quality (Movie))
Procedure
[r] (REC) * [MENU] * Quality Tab * » Quality (Movie)
This setting can be used to specify HD or STD as the image quality for movie
recording when HD/STD is selected as the movie mode.
ratio of movies recorded with this setting is 16:9.
HD
Use this setting for standard movie recording. Recording with this setting is
x
performed using an aspect ratio of 4:3, an image size of 640 480 pixels,
STD
and a frame rate of 30 frames per second. Image quality and image size
settings cannot be changed.
Advanced Settings
Download from Www.Somanuals.com. All Manuals Search And Download.
100
Setting the High Speed Movie Frame Rate (HS » Speed)
Procedure
[r] (REC) * [MENU] * Quality Tab * HS » Speed
Specifying the Metering Mode (Metering)
Procedure
[r] (REC) * [MENU] * Quality Tab * Metering
The metering mode determines what part of the subject is metered for exposure.
Multi-pattern metering divides the image into sections and measures
the light in each section for a balanced exposure reading. This type
of metering provides error-free exposure settings for a wide range of
shooting conditions.
B
Multi
Center weighted metering concentrates on the center of the focus
area to measure light. This type of metering is best when you want
some level of control over contrast.
N
Weighted
Center
Spot metering takes readings at a very small area. Use this metering
method when you want exposure to be set according to the
brightness of a particular subject, without being affected by
surrounding conditions.
˜
Spot
Optimizing Image Brightness (Lighting)
Procedure
[r] (REC) * [MENU] * Quality Tab * Lighting
You can use this setting to optimize the balance between bright areas and dark areas
when shooting images.
On
Off
Performs brightness correction.
Does not perform brightness correction.
Advanced Settings
Download from Www.Somanuals.com. All Manuals Search And Download.
101
Specifying Flash Intensity (Flash Intensity)
Procedure
[r] (REC) * [MENU] * Quality Tab * Flash Intensity
You can specify flash intensity to one of five levels from +2 (brightest flash) to –2
(least bright flash).
• Flash intensity may not change when the subject is too far away or too close.
Using Built-in Color Filters (Color Filter)
Procedure
[r] (REC) * [MENU] * Quality Tab * Color Filter
Settings: Off, B/W, Sepia, Red, Green, Blue, Yellow, Pink, and Purple
Controlling Image Sharpness (Sharpness)
Procedure
[r] (REC) * [MENU] * Quality Tab * Sharpness
You can specify one of five sharpness settings from +2 (sharpest) to –2 (least sharp).
Controlling Color Saturation (Saturation)
Procedure
[r] (REC) * [MENU] * Quality Tab * Saturation
You can specify one of five saturation settings from +2 (most saturated) to –2 (least
saturated).
Adjusting Image Contrast (Contrast)
Procedure
[r] (REC) * [MENU] * Quality Tab * Contrast
You can specify one of five contrast settings from +2 (most contrast between light and
dark) to –2 (least contrast between light and dark).
Advanced Settings
Download from Www.Somanuals.com. All Manuals Search And Download.
102
Viewing Snapshots and Movies
Viewing Snapshots
Viewing a Movie
1. Press [p] (PLAY) and then use [4] and [6] to display the movie you
want to view.
2. Press [SET] to start playback.
Movie icon: »
Recording time
Image quality
Movie Playback Controls
[4] [6] (Playback in progress.)
Fast forward/fast
reverse
• Each press of either button increases the speed of the
fast forward or fast reverse operation.
• To return to normal playback speed, press [2].
Play/pause
[SET]
1 frame forward/
back
[4] [6] (Playback paused.)
• Holding down either button scrolls continuously.
Press [2] and then press [8] [2]
• Volume can be adjusted only while movie playback is in
progress.
Volume adjustment
Information display
on/off
[8] (DISP)
Slide the zoom controller in the direction of z ([).
• You can use [8], [2], [4], and [6] to scroll the zoomed
image on the monitor screen. You can zoom a movie
image up to 4.5 times normal size.
Zoom
Stop playback
[MENU]
• Playback may not be possible for movies not recorded with this camera.
Viewing Snapshots and Movies
Download from Www.Somanuals.com. All Manuals Search And Download.
103
Viewing Continuous Shutter Images
Each time you perform a continuous shutter (CS) operation, the camera creates a CS
group that includes all of the images for that particular CS session. You can use the
following procedure to play back the images in a particular CS group.
1. Press [p] (PLAY) and then use [4] and [6] to display the CS group
whose images you want to view.
Number of image files in
the CS group
CS group icon
First image in the CS group
2. About one second after you select a CS group, high speed playback of
its images will start automatically.
• After playback of a CS Group is complete, the first image of the group will be
displayed on the monitor screen.
• Pressing [SET] will pause playback. While playback is paused, you can adjust
the playback speed, specify the playback direction, scroll forward or back,
zoom images, and delete images.
Current image number/number
of images in the group
CS speed
Playback guide
Viewing Snapshots and Movies
Download from Www.Somanuals.com. All Manuals Search And Download.
104
The following are operations that are supported after you press [SET] to
start image playback.
During playback, changes the playback direction and playback speed.
While playback is paused, scrolls forward or back.
• Playback speed cannot be adjusted while the displayed image is
[4] [6]
zoomed.
[SET]
Toggles between pause and play.
Zooms the image.
• You can use [8], [2], [4], and [6] to scroll the zoomed image on
the monitor screen.
Zoom
controller
[MENU]
Exits CS group playback.
[8] (DISP) Cycles through information display formats.
[2] Displays the “CS Frame Edit” menu.
NOTE
• Multiple images shot using normal-speed continuous shutter are stored individually
not as a CS group.
Deleting Continuous Shutter Images
You can use the following procedures to delete images while playback is in progress
or paused.
. Deleting a Specific CS Group File
1. While CS image playback is in progress or paused (toggle by pressing
[SET]), press [2].
This will display the “CS Frame Edit” menu.
2. Use [8] and [2] to select “Delete” and then press [SET].
3. Use [4] and [6] to display the image you want to delete.
4. Use [8] and [2] to select “Delete” and then press [SET].
• To delete other files, repeat steps 3 and 4.
• To exit the delete operation, press [MENU].
Viewing Snapshots and Movies
Download from Www.Somanuals.com. All Manuals Search And Download.
105
. Deleting All Files in a CS Group
1. While CS image playback is in progress or paused (toggle by pressing
[SET]), press [2].
This will display the “CS Frame Edit” menu.
2. Use [8] and [2] to select “Delete” and then press [SET].
3. Use [8] and [2] to select “Del Group Images” and then press [SET].
4. Use [8] and [2] to select “Yes”, and then press [SET].
NOTE
• Either of the following methods is recommended when you want to keep only one
of the images in a CS group and delete all of the others.
– Copy the image you want to keep to a file located outside of the CS group and
then delete the CS group.
– Protect the image you want to keep and then delete the CS group.
Dividing Up a CS Group
Use the following to divide up a CS Group into individual images.
. Dividing Up a Specific CS Group
1. While a CS group is displayed or while the images of a CS group are
scrolling on the monitor screen, press [MENU].
2. Use [4] and [6] to select the “PLAY” tab.
3. Use [8] and [2] to select “Divide Group” and then press [6].
4. Use [4] and [6] to display the CS group you want to divide up.
5. Use [8] and [2] to select “Divide” and then press [SET].
• To divide up other CS group files, repeat steps 4 and 5.
Viewing Snapshots and Movies
Download from Www.Somanuals.com. All Manuals Search And Download.
106
. Dividing Up All CS Groups
IMPORTANT!
• Once a CS group is divided, it cannot be regrouped.
1. While a CS group is displayed or while the images of a CS group are
scrolling on the monitor screen, press [MENU].
2. Use [4] and [6] to select the “PLAY” tab.
3. Use [8] and [2] to select “Divide Group” and then press [6].
4. Use [8] and [2] to select “Divide All Groups” and then press [SET].
5. Use [8] and [2] to select “Yes”, and then press [SET].
Copying a CS Group Image
Use the following procedure to copy an image in a CS group to a location outside of
the group.
1. While CS image playback is in progress or paused (toggle by pressing
[SET]), press [2].
This will display the “CS Frame Edit” menu.
2. Use [8] and [2] to select “Copy”, and then press [SET].
3. Use [4] and [6] to display the image you want to copy.
4. Use [8] and [2] to select “Copy”, and then press [SET].
NOTE
• The functions below cannot be performed on snapshots inside a CS group. Before
using either of these functions, perform the above procedure to copy the image
first.
White Balance, Brightness, Trimming, Rotation, Resize
Viewing Snapshots and Movies
Download from Www.Somanuals.com. All Manuals Search And Download.
107
Zooming an On-screen Image
1. In the PLAY mode, use [4] and [6] to scroll through the images until
the one you want is displayed.
2. Slide the zoom controller towards z ([) to
Zoom factor
zoom.
Image area
You can use [8], [2], [4], and [6] to scroll the zoomed
image on the monitor screen. Slide the zoom controller
towards w to unzoom the image.
– When monitor screen contents are turned on, a
graphic in the lower right corner of the screen
shows what part of the zoomed image is currently
displayed.
– To exit the zoom screen, press [MENU].
– Though the maximum image zoom factor is 8X,
certain image sizes may not allow zooming up to
the full 8X.
Current display area
• Pressing [SET] will lock the current zoom factor for the on-screen image. You
can then use [4] and [6] to scroll between images, using the same zoom
factor. Pressing [SET] again will unlock the zoom factor and allow you to use
[8], [2], [4] and [6] to move around the currently displayed images. This
function cannot be used while viewing CS group images or movies. Also, CS
group images and movies will not appear when you are scrolling images with
[4] and [6].
Displaying the Image Menu
1. In the PLAY mode, slide the zoom controller
Boundary
towards w (]).
Use [8], [2], [4] and [6] to move the selection
boundary around the image menu.
To view a particular image, use [8], [2], [4], or [6] to
move the selection boundary to the image you want and
then press [SET].
• In the case of a movie or a continuous shutter (CS)
file, the first frame of the file will be displayed.
Viewing Snapshots and Movies
Download from Www.Somanuals.com. All Manuals Search And Download.
108
Viewing Snapshots and Movies on a TV Screen
1. Use the AV cable that comes with the camera to connect it to the TV.
AV cable (bundled)
Yellow
White
USB/AV port
Video
Audio
TV
AUDIO IN jack (white)
VIDEO IN jack (yellow)
Making sure that the 6 mark on the
camera is aligned with the 4 mark of the
AV cable connector, connect the cable to
the camera.
Terminal cover
• Make sure that you insert the cable connector into the USB/AV port until you
feel it click securely into place. Failure to insert the connector fully can result in
poor communication or malfunction.
• Note that even while the connector is fully inserted, you
still will be able to see the metal part of the connector as
shown in the illustration.
• Make sure that the camera is turned off before plugging
in or unplugging the cable. Check the user
documentation that comes with the TV for information
about requirements before plugging into or unplugging from the TV.
2. Turn on the TV and select its video input mode.
If the TV has more than one video input, select the one where the camera is
connected.
3. Press [p] (PLAY) to turn on the camera.
This will cause an image to appear on the TV screen, without anything appearing
on the camera’s monitor screen.
• Pressing [ON/OFF] or [r] (REC) will not turn on the camera while the AV
cable is connected.
• You also can change the aspect ratio of the screen and the video output
system (page 159).
Viewing Snapshots and Movies
Download from Www.Somanuals.com. All Manuals Search And Download.
109
4. Now you can display images and play back movies as you normally do.
IMPORTANT!
• Output to a TV is not supported while the camera is in the REC mode.
• When the camera is connected to a TV for movie playback, only movie images are
displayed on the TV screen. The camera’s monitor screen will show on-screen
information only (without any movie image).
• Before connecting to a TV to display images, be sure to configure the camera’s
• Audio is initially output by the camera at maximum volume. When you first start
displaying images, set the TV volume control at a relatively low level and then
adjust it as required.
NOTE
• Audio is monaural.
• Some TVs may not be able to output images and/or audio correctly.
• All icons and indicators that appear on the monitor screen also appear on the TV
screen. You can use [8] (DISP) to change the display contents.
Recording Camera Images to a DVD Recorder or Video Deck
Use the following method to connect the camera to the recording device using the
camera’s bundled AV cable.
– DVD recorder or video deck: Connect the AV cable to the VIDEO IN and AUDIO IN
terminals.
– Camera: Connect the AV cable to the USB/AV port.
You can play a slideshow of snapshots and movies on the camera and record it on a
DVD or video tape. You can record movies by selecting “» Only” for the slideshow
“Images” setting (page 111).
For information about connecting a monitor to the recording device and about how to
record, see the user documentation that comes with the recording device you are
using.
Viewing Snapshots and Movies
Download from Www.Somanuals.com. All Manuals Search And Download.
110
Other Playback Functions (PLAY)
This section explains menu items that you can use to configure settings and perform
other playback operations.
Playing a Slideshow on the Camera (Slideshow)
Procedure
[p] (PLAY) * [MENU] * PLAY Tab * Slideshow
Start
Starts the slideshow
Images
Specifies the type of images to be included in the slideshow
All images: Snapshots, movies, continuous shutter images
Z
All images except
: All non-continuous shutter (CS) images
T
Only: Snapshots only
» Only: Movies only
One Image: One single selected image (selected using [4] and [6])
Time
Time from the start to the end of the slideshow
1 to 5 minutes, 10 minutes, 15 minutes, 30 minutes, 60 minutes
Interval
Amount of time each image remains displayed
Use [4] and [6] to select a value from 1 to 30 seconds, or “MAX”.
If you specify a value from 1 to 30 seconds, movies play from beginning to end.
When the slideshow reaches a movie file while “MAX” is selected, only the first
frame of the movie will displayed.
Other Playback Functions (PLAY)
Download from Www.Somanuals.com. All Manuals Search And Download.
111
Effect
Select the effect you want.
Pattern 1 to 5: Plays background music and applies an image change effect.
• Patterns 2 through 4 have different background music, but they all use the
same image change effect.
• Pattern 5 can be used for playback of snapshots only (except for those that
are part of a CS group), and the “Interval” setting is ignored.
• Movies that include audio are played back without background music. Movies
that do not include audio are played back with background music.
• The currently selected image change effect setting is disabled automatically
in following cases.
– When playing a slideshow for which “» Only” or “One Image” is selected
for the “Images” setting
– When the interval setting is “MAX”, 1 second, or 2 seconds
– Before and after playback of a movie
– During CS group playback (Except the Pattern 1 effect)
Off: No image change effect or background music
• To stop the slideshow, press [SET] or [MENU]. Pressing [MENU] stops the
slideshow and returns to the menu screen.
• Adjust audio volume by pressing [2] and then press [8] or [2] during playback.
• All button operations are disabled while the slideshow is transitioning from one
image to another.
• The time required for transition from one image to another may be longer in the
case of an image that was not recorded with this camera.
Other Playback Functions (PLAY)
Download from Www.Somanuals.com. All Manuals Search And Download.
112
Transferring Music from Your Computer to Camera Memory
You can replace the built-in slideshow background music with other music from your
computer.
Supported File Types:
• PCM format (16-bit, monaural) WAV files
• Sampling Frequencies: 11.025 kHz/22.05 kHz/44.1 kHz
* Even if a file is recorded in stereo, playback will be monaural.
Number of Files: 9
File names: SSBGM001.WAV to SSBGM009.WAV
• Create the music files on your computer using the above names.
• Regardless of which effect pattern you select, the music files you store in camera
memory are played back in name sequence.
If you plan to save the music files to the camera’s memory card, make sure the
card is loaded in the camera.
2. Perform one of the following operations to open the memory card or
built-in memory.
This will cause the camera to be recognized by your computer as a Removable
Disk (Drive).
• Windows
Windows 7/Vista: Start * Computer
Windows XP: Start * My Computer
1
Windows 2000: Double-click “My Computer”.
Double-click “Removable Disk”.
• Macintosh
2
Double-click the camera’s drive icon.
1
3. Create a folder named “SSBGM”.
Other Playback Functions (PLAY)
Download from Www.Somanuals.com. All Manuals Search And Download.
113
4. Double-click the “SSBGM” folder you created and copy the
background music file to it.
• See the user documentation that comes with your computer for information
about moving, copying, and deleting files.
• If there are background music files both in built-in memory and on the memory
card loaded in the camera, the files on the memory card take priority.
Creating a Snapshot of Movie Frames (MOTION PRINT)
Procedure
[p] (PLAY) * Movie Screen * [MENU] * PLAY Tab *
MOTION PRINT
1. Use [4] and [6] to scroll
through the movie frames
and display the one you
want to use as the image
of the MOTION PRINT
image.
Holding down [4] or [6]
scrolls at high speed.
9 frames
1 frame
2. Use [8] and [2] to select either “9 frames” or “1 frame” and then
press [SET].
• When “9 frames” is selected, the frame you select in step 1 will be in the center
of the MOTION PRINT image.
• Only the frames of movies recorded on this camera can be used in a MOTION
PRINT image.
Other Playback Functions (PLAY)
Download from Www.Somanuals.com. All Manuals Search And Download.
114
Editing a Movie on the Camera (Movie Editing)
Procedure
[p] (PLAY) * Movie Screen of Movie to be Edited * [MENU] *
PLAY Tab * Movie Editing
The Movie Editing feature lets you use one of the following procedures to edit out a
specific part of a movie.
}
(To-Point Cut)
Cut
Cuts everything from the beginning of the movie up to the
current location.
~
Cut
(Point-To-Point Cut)
Cuts everything between two points.
¡
Cut
(From-Point Cut)
Cuts everything from the current location to the end of the
movie.
1. Use [8] and [2] to select the editing method you want to use and then
press [SET].
2. Use the following operations to select the frame
(point) from which or to which you want to cut
the movie (the cut point).
During playback, changes the playback
[4] [6] direction and playback speed. While
playback is paused, scrolls forward or back.
Cut range (yellow)
[SET]
Toggles between pause and play.
Other Playback Functions (PLAY)
Download from Www.Somanuals.com. All Manuals Search And Download.
115
3. Press [2] to display the editing menu and specify one or two cut
points.
}
Cut
(To-Point Cut)
While the frame you want the cut to be up to is
displayed, press [2].
While the frame you want the first (From) cut to be is
displayed, press [2].
1
~
Cut
(Point-To-Point Cut)
Select another frame.
While the frame you want the second (To) cut to be
is displayed, press [2].
2
3
¡
Cut
(From-Point Cut)
While the frame you want the cut to be from is
displayed, press [2].
4. Use [8] and [2] to select “Yes” and then press [SET].
The selected cut operation will take considerable time to complete. Don’t try to
perform any camera operation until the “Busy... Please wait...” message
disappears from the monitor screen. Note that a cut operation can take a long
time if the movie being edited is long.
IMPORTANT!
• When you edit a movie, only the result is saved. The original movie is not retained.
An editing operation cannot be undone.
NOTE
• A movie that is shorter than five seconds cannot be edited.
• Editing of movies recorded with a different type of camera is not supported.
• You will not be able to edit a movie if the amount of remaining memory capacity is
less than the size of the movie file you want to edit. If there is not enough memory
available, delete files you no longer need to free up more.
• Splitting of a movie into two movies and splicing of two different movies into a
single movie are not supported.
• You also can start a movie editing operation while the movie you want to edit is
playing back. When playback reaches a frame where you want a cut point to be,
press [SET] to pause playback. Next, press [2] to display the menu of editing
options. Perform editing using the same procedures as described above.
Other Playback Functions (PLAY)
Download from Www.Somanuals.com. All Manuals Search And Download.
116
Adjusting White Balance (White Balance)
Procedure
[p] (PLAY) * Snapshot Screen * [MENU] * PLAY Tab *
White Balance
You can use the white balance setting to select a light source type for a recorded
image, which will affect the colors of the image.
¤
'
“
Daylight
Overcast
Shade
Outdoors, fair weather
Outdoors, cloudy to rain, in tree shade, etc.
Very high temperature light, such as building shade, etc.
†
Day White
Fluorescent
White or day white fluorescent lighting, without suppressing
color cast
–
Daylight
Fluorescent
Daylight fluorescent lighting, while suppressing color cast
«
Tungsten
Suppressing of the appearance of light bulb lighting
No white balance adjustment
Cancel
NOTE
• The original snapshot is retained in memory and not deleted.
• When you display an altered image on the camera’s monitor screen, the date and
time indicates when the image was originally recorded, not when the image was
altered.
Other Playback Functions (PLAY)
Download from Www.Somanuals.com. All Manuals Search And Download.
117
Adjusting the Brightness of an Existing Snapshot
(Brightness)
Procedure
[p] (PLAY) * Snapshot Screen * [MENU] * PLAY Tab *
Brightness
You can select one of five brightness levels, from +2 (brightest) to –2 (least bright).
NOTE
• The original snapshot is retained in memory and not deleted.
• When you display an altered image on the camera’s monitor screen, the date and
time indicates when the image was originally recorded, not when the image was
altered.
Selecting Images for Printing (DPOF Printing)
Procedure
[p] (PLAY) * Snapshot Screen * [MENU] * PLAY Tab *
DPOF Printing
Other Playback Functions (PLAY)
Download from Www.Somanuals.com. All Manuals Search And Download.
118
Protecting a File Against Deletion (Protect)
Procedure
[p] (PLAY) * [MENU] * PLAY Tab * Protect
Protects specific files.
Use [4] and [6] to scroll through the files
until the one you want to protect is displayed.
1
Use [8] and [2] to select “On” and then
press [SET].
2
On
An image that is protected is indicated by the
› icon.
To protect other files, repeat steps 1 and 2.
To exit the protect operation, press [MENU]. To unprotect a file, select
“Off” instead of “On” in step 2 above.
3
Protects all files.
Use [8] and [2] to select “All Files: On” and then press [SET].
Press [MENU].
To unprotect all files, select “All Files: Off” instead of “All Files: On” in
step 1 above.
1
2
All Files:
On
IMPORTANT!
• Note that even if a file is protected, it will be deleted if you perform the format
operation (page 160).
NOTE
• Performing the above procedure while a CS group is displayed will protect all the
images in the CS group. You can protect individual images in a CS group by
performing the above procedure while the image is displayed.
. To protect a specific image in a CS group
1. While CS image playback is in progress or paused (toggle by pressing
[SET]), press [2].
This will display the “CS Frame Edit” menu.
2. Use [8] and [2] to select “Protect” and then press [SET].
Other Playback Functions (PLAY)
Download from Www.Somanuals.com. All Manuals Search And Download.
119
3. Use [4] and [6] to scroll through images until one you want to protect
is displayed.
4. Use [8] and [2] to select “On” and then press [SET].
This will protect the image and display the › icon.
• To unprotect an image, select “Off” in step 4 and then press [SET].
5. After you are finished, select “Cancel” and then press [SET] to exit this
operation.
NOTE
• Note that even if a file is protected, it will be deleted if you perform the format
operation (page 160).
. To protect all the images in a CS group
1. While a CS group is displayed or while the images of a CS group are
scrolling on the monitor screen, press [MENU].
2. Use [4] and [6] to select the “PLAY” tab.
3. Use [8] and [2] to select “Protect” and then press [SET].
4. Use [4] and [6] to display the CS group you want to protect.
5. Use [8] and [2] to select “On” and then press [SET].
This will protect all the images in the group and display the › icon.
• To unprotect all of the images in the group, select “Off” in step 5 and then press
[SET].
6. Press [MENU].
NOTE
• Note that even if a file is protected, it will be deleted if you perform the format
operation (page 160).
Other Playback Functions (PLAY)
Download from Www.Somanuals.com. All Manuals Search And Download.
120
Rotating an Image (Rotation)
Procedure
[p] (PLAY) * Snapshot Screen * [MENU] * PLAY Tab * Rotation
1. Use [8] and [2] to select “Rotation” and then press [SET].
Each press of [SET] will rotate the displayed image 90 degrees left.
2. When the displayed image is at the orientation you want, press
[MENU].
NOTE
• Rotating a CS image causes all of the images in the CS group to be rotated. You
cannot rotate individual component image in a CS group.
• Rotation of movie images is not supported.
• Note that this procedure does not actually change the image data. It simply alters
how the image is displayed on the camera’s monitor screen.
• An image that has been protected or zoomed cannot be rotated.
• The original (unrotated) version of the image will be displayed on the image menu
screen.
Resizing a Snapshot (Resize)
Procedure
[p] (PLAY) * Snapshot Screen * [MENU] * PLAY Tab * Resize
You can reduce the size of a snapshot and save the result as a separate snapshot.
The original snapshot is also retained. You can resize an image to one of three sizes:
5M, 2M, VGA.
• Resizing a 3:2 or 16:9 size snapshot will create an image with an aspect ratio of
4:3, with both sides cut off.
• The recording date of the resized version of the snapshot will be the same as the
recording date of the original snapshot.
Other Playback Functions (PLAY)
Download from Www.Somanuals.com. All Manuals Search And Download.
121
Cropping a Snapshot (Trimming)
Procedure
[p] (PLAY) * Snapshot Screen * [MENU] * PLAY Tab * Trimming
You can crop a snapshot to trim parts you do not need, and
save the result in a separate file. The original snapshot is
also retained.
Zoom factor
Represents
snapshot area
Use the zoom controller to zoom the image to the size you
want, use [8], [2], [4], and [6] to display the portion of
the image you want to cut out, and then press [SET].
• The image produced by cropping a 3:2 or 16:9 image will
have an aspect ratio of 4:3.
• The recording date of the cropped image will be the
same as the recording date of the original snapshot.
Part of snapshot that is
currently displayed
Copying Files (Copy)
Procedure
[p] (PLAY) * Snapshot Screen * [MENU] * PLAY Tab * Copy
Files can be copied from the camera’s built-in memory to a memory card or from a
memory card to built-in memory.
Copies all files from built-in camera memory to a memory card.
This option copies all the files in built-in camera memory. It cannot be
used to copy a single file.
Built-in *
Card
Copies a single file on the memory card to camera built-in camera
memory. Files are copied to the folder in built-in memory whose
name has the largest serial number.
• You cannot copy a continuous shutter (CS) group image (page
Card *
Built-in
Use [4] and [6] to select the file you want to copy.
Use [8] and [2] to select “Copy” and then press [SET].
1
2
NOTE
• You can copy snapshots or movies you recorded with this camera.
Other Playback Functions (PLAY)
Download from Www.Somanuals.com. All Manuals Search And Download.
122
Dividing Up a Continuous Shutter Group (Divide Group)
Procedure
[p] (PLAY) * [MENU] * PLAY Tab * Divide Group
Combining CS Images into a Single Still Image
(CS Multi Print)
Procedure
[p] (PLAY) * Display CS group. * [MENU] * PLAY Tab *
CS Multi Print
1. Use [8] and [2] to select “Create”.
• You can use [4] and [6] to select a different CS group, if you want.
2. Press [SET].
x
This converts the CS group to a 10M (3648 2736) image with up to 30 CS
x
frames (5 vertical 6 horizontal).
• This camera may not be able to correctly convert a CS group image with
another camera.
• The recording date of the converted image will be the same as the recording
date of the original CS group.
• When converting a CS group whose images have been rotated by the
“Rotation” feature to a CS Multi Print image, the arrangement of the images in
the CS Multi Print will be different from that of normal (unrotated) CS images.
Editing a CS Image (CS Frame Edit)
Procedure
[p] (PLAY) * [MENU] * PLAY Tab * CS Frame Edit
See the following pages for details.
DPOF Printing: page 128
Copy: page 107
Delete: page 105
Other Playback Functions (PLAY)
Download from Www.Somanuals.com. All Manuals Search And Download.
123
Printing
Printing Snapshots
Professional Print Service
You can take a memory card that contains the images you want
to print to a professional print service and have them printed.
Printing on a Home Printer
Printing Images on a Printer with Memory Card Slot
You can use a printer equipped with a memory card slot to print
images directly from a memory card. For details, see the user
documentation that comes with your printer.
Connecting Directly to a PictBridge Compatible
Printer
You can print on a printer that supports PictBridge (page
Printing with a Computer
After transferring the images to your computer, use
commercially available software to print.
• You can specify which images you want to print, the number of copies, and date
Connecting Directly to a PictBridge Compatible Printer
You can connect the camera directly to a printer that supports PictBridge and print
images without going through a computer.
. To set up the camera before connecting to a printer
1. Turn on the camera and press [MENU].
2. On the “Set Up” tab, select “USB” and then press [6].
3. Use [8] and [2] to select “PTP (PictBridge)”, and then press [SET].
Printing
Download from Www.Somanuals.com. All Manuals Search And Download.
124
. Connecting the Camera to a Printer
Use the USB cable that comes bundled with the camera to connect the camera to
your printer’s USB port.
USB cable
Large connector
USB/AV port
USB
Small connector
USB port
Terminal
Making sure that the 6 mark on the camera is aligned
with the 4 mark of the USB cable connector, connect
cover
the cable to the camera.
• The camera does not draw power over the USB cable. Check the battery level
before connecting and make sure it is not too low.
• Make sure that you insert the cable connector into the USB/AV port until you feel it
click securely into place. Failure to insert the connector fully can result in poor
communication or malfunction.
• Note that even while the connector is fully inserted, you still
will be able to see the metal part of the connector as shown
in the illustration.
• When connecting the USB cable to a USB port, make sure
you align the connector correctly with the port.
• Make sure that the camera is turned off before plugging in or
unplugging the cable. Check the user documentation that comes with the printer for
information about requirements before plugging into or unplugging from the printer.
Printing
Download from Www.Somanuals.com. All Manuals Search And Download.
125
. To print
1. Turn on the printer and load paper.
2. Turn on the camera.
This will display the print menu screen.
3. Use [8] and [2] to select “Paper Size”, and then press [6].
4. Use [8] and [2] to select a paper size and then press [SET].
• The following are the available paper sizes.
x
x
x
x
3.5" 5", 5" 7", 4" 6", A4, 8.5" 11", By Printer
• Selecting “By Printer” prints using a paper size selected on the printer.
• See the documentation that comes with your printer for information about
paper settings.
5. Use [8] and [2] to specify the print option you want.
1 Image
: Prints one image. Select and then press [SET]. Next, use [4]
and [6] to select the image you want to print.
DPOF Printing : Prints multiple images. Select and then press [SET]. With this
option, images will be printed in accordance with DPOF settings
(page 127).
• To toggle date stamping on and off, press [BS]. The date stamp will be printed
when “On” is indicated on the monitor screen.
6. Use [8] and [2] to select “Print” and then press [SET].
Printing will start and the message “Busy... Please wait...” will appear on the
monitor screen. The message will disappear after a short while, even though
printing is still being performed. Pressing any camera button will cause the
printing status to re-appear. The print menu screen will re-appear when printing is
complete.
• If you selected “1 Image”, you can repeat the procedure from step 5, if you
want.
7. After printing is complete, turn off the camera and disconnect the USB
cable from the printer and camera.
Printing
Download from Www.Somanuals.com. All Manuals Search And Download.
126
Using DPOF to Specify Images to be Printed and the Number
of Copies
. Digital Print Order Format (DPOF)
DPOF is a standard that allows you to include image type, number of copy,
and time stamp on/off information on the memory card with the images.
After configuring settings, you can use the memory card to print on a home
printer that supports DPOF or take the memory card to a professional print
service.
• Whether or not you will be able to use DPOF settings for printing depends on the
printer you are using.
• Some professional print services may not support DPOF.
. Configuring DPOF Settings Individually for Each Image
Procedure
[p] (PLAY) * Snapshot Screen * [MENU] * PLAY Tab *
DPOF Printing * Select images
1. Use [4] and [6] to scroll through the files until the image you want to
print is displayed.
2. Use [8] and [2] to specify the number of copies.
You can specify a value up to 99. Specify 00 if you do not want to print the image.
• If you want to include the date in the images, press [BS] so “On” is shown for
date stamping.
• Repeat steps 1 and 2 to configure settings for other images, if you want.
3. Press [SET].
Printing
Download from Www.Somanuals.com. All Manuals Search And Download.
127
. Configuring the Same DPOF Settings for All the Images
Procedure
[p] (PLAY) * Snapshot Screen * [MENU] * PLAY Tab *
DPOF Printing * All images
1. Use [8] and [2] to specify the number of copies.
You can specify a value up to 99. Specify 00 if you do not want to print the image.
• Note that the specified number of copies will be printed for all of the images in
any CS group included with the images.
• If you want to include the date in the images, press [BS] so “On” is shown for
date stamping.
2. Press [SET].
NOTE
image in the group is displayed.
. To specify the number of copies for a specific image in a CS group
1. While CS image playback is in progress or paused (toggle by pressing
[SET]), press [2].
This will display the “CS Frame Edit” menu.
2. Use [8] and [2] to select “DPOF Printing” and then press [SET].
3. Use [8] and [2] to select “Select images” and then press [SET].
4. Use [4] and [6] to scroll through images until one you want to print is
displayed.
Printing
Download from Www.Somanuals.com. All Manuals Search And Download.
128
5. Use [8] and [2] to specify the number of copies.
You can specify a value up to 99. Specify 00 if you do not want to print the image.
• If you want to include the date in the images, press [BS] to select “On” for date
stamping.
• Repeat steps 4 and 5 to configure settings for other images, if you want.
6. Press [SET].
. To configure the same DPOF settings for all the images in a CS
group
1. While CS image playback is in progress or paused (toggle by pressing
[SET]), press [2].
This will display the “CS Frame Edit” menu.
2. Use [8] and [2] to select “DPOF Printing” and then press [SET].
3. Use [8] and [2] to select “Frame all” and then press [SET].
4. Use [8] and [2] to specify the number of copies.
You can specify a value up to 99. Specify 00 if you do not want to print the image.
• If you want to include the date in the images, press [BS] to select “On” for date
stamping.
5. Press [SET].
Printing
Download from Www.Somanuals.com. All Manuals Search And Download.
129
DPOF settings are not cleared automatically after printing is complete.
The next DPOF print operation you execute will be performed using the last DPOF
settings you configured for the images. To clear DPOF settings, specify “00” for the
number of copies of all images.
Tell your print service about your DPOF settings!
If you take a memory card to a professional print service, be sure to tell them that it
includes DPOF settings for the images to be printed and the number of copies. If you
don’t, the print service may print all the images without regard to your DPOF settings,
or they may ignore your date stamp setting.
. Date Stamping
You can use one of the following three methods to include the recording date in the
printout of an image.
Configuring camera settings
Configure DPOF settings (page 127).
You can turn date stamping on and off each time you print. You can configure
settings so some images include the date stamp and some don’t.
Configure the Camera’s Timestamp setting (page 155).
• The camera’s Timestamp setting imprints the date into a snapshot when you
shoot it, so the date is always included when you print. It cannot be deleted.
• Do not turn on DPOF date stamping for an image that includes a date
stamped with the camera’s Timestamp function. Doing so can cause the two
stamps to be overprinted.
Configuring computer settings
You can use commercially available image management software to date
stamp images.
Professional print service
Request date stamping when ordering prints from a professional print service.
Printing
Download from Www.Somanuals.com. All Manuals Search And Download.
130
. Standards Supported by the Camera
• PictBridge
This is a standard of the Camera and Imaging Products Association
(CIPA). You can connect the camera directly to a printer that supports
PictBridge, and perform image selection and printing using the
camera monitor screen and controls.
• PRINT Image Matching III
Using image editing software and printing on a printer that supports
PRINT Image Matching III makes it possible to use information about
shooting conditions that is recorded with the image, and produce
exactly the type of image you want. PRINT Image Matching and
PRINT Image Matching III are trademarks of Seiko Epson Corporation.
• Exif Print
Printing on a printer that supports Exif Print (Exif 2.2) uses
information about shooting conditions recorded with the image to
enhance printed image quality. Contact your printer manufacturer
for information about models that support Exif Print, printer upgrades, etc.
Printing
Download from Www.Somanuals.com. All Manuals Search And Download.
131
Using the Camera with a Computer
Things you can do using a computer...
You can perform the operations described below while the camera is connected to a
computer.
Save images to a
computer and view
them there
• Save images and view them manually
• Transfer images to a computer
automatically over a wireless LAN for
viewing (Eye-Fi) (page 147).
Transfer images
stored on your
computer to
In addition to images, you also can transfer
screen shot images from your computer to
camera memory
Play back and edit
movies
• To edit movies, use commercially
available software as required.
* Windows only
The procedures you need to perform when using the camera with your computer and
when using the bundled software are different for Windows and the Macintosh.
Using the Camera with a Computer
Download from Www.Somanuals.com. All Manuals Search And Download.
132
Using the Camera with a Windows Computer
Install the required software in accordance with the version of Windows you are
running and what you want to do.
When you want to Operating System
See
page:
Install this software:
do this:
Version
Save images to a
computer and view
them there manually
7 / Vista / XP / 2000
Installation not required.
Installation not required.
• Windows Media Player,
which is already installed
on most computers, can be
used for playback.
• If your computer is running
Windows 2000 and does
not have DirectX 9.0c or
higher installed, download
DirectX from the Microsoft
DirectX site and install it on
your computer.
Play movies
7 / Vista / XP / 2000
–
Edit movies
7 / Vista / XP / 2000
• Use commercial software
as required.
–
Upload movie files
to YouTube
7 / Vista / XP (SP2/
SP3) / 2000 (SP4)
YouTube Uploader for
CASIO*
Transfer images to
the camera
7 / Vista / XP / 2000
Photo Transport 1.0*
Adobe Reader 8
(Not required if already
installed.)
View the User’s
Guide
Vista / XP (SP2/SP3) /
2000 (SP4)
* YouTube Uploader for CASIO and Photo Transport will not run under 64-bit versions of
Windows OS.
Using the Camera with a Computer
Download from Www.Somanuals.com. All Manuals Search And Download.
133
. Computer System Requirements for Bundled Software
Computer system requirements are different for each of the applications. See the
“Read me” file that comes with each application for details. Information about
computer system requirements also can be found under “Computer System
. Precautions for Windows Users
• Except for Adobe Reader, the bundled software requires Administrator privileges to
run.
• Operation under a dual-processor environment is not supported.
• Operation may not be possible under certain computer environments.
Viewing and Storing Images on a Computer
You can connect the camera to your computer in order to view and store images
(snapshot and movie files).
. To connect the camera to your computer and save files
1. Turn on the camera and press [MENU].
2. On the “Set Up” tab, select “USB” and then press [6].
3. Use [8] and [2] to select “Mass Storage”, and then press [SET].
Using the Camera with a Computer
Download from Www.Somanuals.com. All Manuals Search And Download.
134
4. Turn off the camera and then use the USB cable that comes with the
camera to connect it to your computer.
USB port
USB cable
Large connector
USB/AV port
Small connector
Terminal
Making sure that the 6 mark on the camera is aligned
with the 4 mark of the USB cable connector, connect
cover
the cable to the camera.
• The camera does not draw power over the USB cable. Check the battery level
before connecting and make sure it is not too low.
• Make sure that you insert the cable connector into the USB/AV port until you
feel it click securely into place. Failure to insert the connector fully can result in
poor communication or malfunction.
• Note that even while the connector is fully inserted, you
still will be able to see the metal part of the connector as
shown in the illustration.
• When connecting the USB cable to a USB port, make
sure you align the connector correctly with the port.
• Your computer may not be able to recognize the
camera if you connect via a USB hub. Always connect directly to the
computer’s USB port.
5. Turn on the camera.
6. Windows 7/Vista users: Click “Start” and then “Computer”.
Windows XP users: Click “Start” and then “My Computer”.
Windows 2000 users: Doubleclick “My Computer”.
Using the Camera with a Computer
Download from Www.Somanuals.com. All Manuals Search And Download.
135
7. Double-click “Removable Disk”.
• Your computer recognizes the memory card loaded in the camera (or built-in
memory if there is no card) as a removable disk.
8. Right-click the “DCIM” folder.
9. On the shortcut menu that appears, click “Copy”.
10. Windows 7/Vista users: Click “Start” and then “Documents”.
Windows XP users: Click “Start” and then “My Documents”.
Windows 2000 users: Doubleclick “My Documents” to open it.
• If you already have a “DCIM” folder in “Documents” (Windows 7/Vista) or “My
Documents” (Windows XP/2000), the next step will overwrite it. If you want to
keep the existing “DCIM” folder, you need to change its name or move it to a
different location before performing the next step.
11. Windows 7 users: On the “Documents” “Organize” menu, select
“Paste”.
Windows Vista users: On the “Documents” “Edit” menu, select
“Paste”.
Windows XP/2000 users: On the “My Documents” “Edit” menu, select
“Paste”.
This will paste the “DCIM” folder (and all the image files it contains) into your
“Documents” (Windows 7/Vista) or “My Documents” (Windows XP/2000) folder.
You now have a copy of the files that are in camera memory on your computer.
12. After you finish copying images, disconnect the camera from the
computer.
Windows 7, Windows Vista, Windows XP
On the camera, press [ON/OFF] to turn off the camera. After making sure that the
back lamp is unlit, disconnect the camera from the computer.
Windows 2000
Click card services in the task tray on your computer screen, and disable the
drive number assigned to the camera. Next, after making sure that the back lamp
is unlit, press the camera’s [ON/OFF] button to turn off the camera and
disconnect the camera from your computer.
Using the Camera with a Computer
Download from Www.Somanuals.com. All Manuals Search And Download.
136
. To view images you copied to your computer
1. Double-click the copied “DCIM” folder to open it.
2. Double-click the folder that contains the images you want to view.
3. Double-click the image file you want to view.
• An image that was rotated on the camera will be displayed on your computer
screen in its original (unrotated) orientation.
• Viewing a CS image on a computer will individually display the component
images in the CS group. A CS group cannot be viewed as a CS image on a
computer.
Never use your computer to modify, delete, move, or rename any image files
that are in the camera’s built-in memory or on its memory card.
Doing so can cause problems with the camera’s image management data, which
will make it impossible to play back images on the camera and can drastically alter
remaining memory capacity. Whenever you want to modify, delete, move, or
rename an image, do so only on images that are stored on your computer.
IMPORTANT!
• Never unplug the USB cable, or operate the camera while viewing or storing
images. Doing so can cause data to become corrupted.
Using the Camera with a Computer
Download from Www.Somanuals.com. All Manuals Search And Download.
137
Playing Movies
Windows Media Player, which is already installed on most computers, can be used
for movie playback. To play back a movie, first copy the movie to your computer and
then double-click the movie file.
. Minimum Computer System Requirements for Movie Playback
The minimum system requirements described below are necessary to play back
movies recorded with this camera on a computer.
Operating System : Windows 7 / Vista / XP / 2000
CPU
: Pentium 4 3.2 GHz or higher
Required Software : Windows Media Player, DirectX 9.0c or higher
• The above are recommended system environments. Configuring one of these
environments does not guarantee proper operation.
• Certain settings and other installed software may interfere with proper playback of
movies.
. Movie Playback Precautions
• Be sure to move the movie data to the hard disk of your computer before trying to
play it. Proper movie playback may not be possible for data accessed over a
network, from a memory card, etc.
• Proper movie playback may not be possible on some computers. If you experience
problems, try the following.
– Try recording movies with a quality setting of “STD”.
– Try upgrading Windows Media Player to the latest version.
– Quit any other applications you have running, and stop resident applications.
Even if proper playback is not possible on the computer, you can use the AV cable
that comes bundled with the camera to connect to the video input terminal of a TV or
computer and play back movies that way.
Using the Camera with a Computer
Download from Www.Somanuals.com. All Manuals Search And Download.
138
Uploading Movie Files to YouTube
Installing YouTube Uploader for CASIO from the CD-ROM that comes with your
camera simplifies uploading of movie files you recorded with the “For YouTube”
scene to YouTube.
. What is YouTube?
YouTube is a movie sharing site managed by YouTube, LLC where you can upload
movies and view movies uploaded by others.
. To install YouTube Uploader for CASIO
1. On the CD-ROM menu screen, select “YouTube Uploader for CASIO”.
2. After reading the information about installation conditions and system
requirements for installation in the “Read me” file, install YouTube
Uploader for CASIO.
. To upload a movie file to YouTube
• Before you can use YouTube Uploader for CASIO, you need to go to the YouTube
website (http://www.youtube.com/) and register as a user there.
• Do not upload any video that is copyrighted (including neighboring copyrights)
unless you yourself own the copyright or you have obtained the permission of the
applicable copyright holder(s).
• The maximum file size for each upload is 1024MB or 10 minutes of playing time.
1. Record the movie you want to upload using the “For YouTube” scene
2. If it isn’t already, connect your computer to the Internet.
4. Turn on the camera.
YouTube Uploader for CASIO will start up automatically.
• If this is the first time you are using the application, configure the YouTube user
ID and network environment settings, and then click the [OK] button.
Using the Camera with a Computer
Download from Www.Somanuals.com. All Manuals Search And Download.
139
5. The left side of the display will have an area for inputting a title,
category, and other information required for uploading to YouTube.
Enter the required information.
6. The right side of the display shows a list of movie files in camera
memory. Select the check box next to the movie file you want to
upload.
7. When everything is ready, click the [Upload] button.
This will upload the movie file(s) to YouTube.
• After uploading is complete, click the [Exit] button to exit the application.
Viewing User Documentation (PDF Files)
1. Start up your computer, and place the bundled CD-ROM into its CD-
ROM drive.
Normally, this should cause the menu screen to appear automatically. If your
computer does not display the menu screen automatically, navigate to the CD-
ROM on your computer and then double-click the “AutoMenu.exe” file.
2. On the menu screen, click the “Language” down arrow button and then
select the language you want.
3. Click “Manual” to select it and then click “Digital Camera”.
IMPORTANT!
• You must have Adobe Reader or Adobe Acrobat Reader installed on your
computer in order to view the contents of a PDF file. If you do not already have
Adobe Reader or Adobe Acrobat Reader installed, install Adobe Reader from the
bundled CD-ROM.
Using the Camera with a Computer
Download from Www.Somanuals.com. All Manuals Search And Download.
140
Transferring Images from Your Computer to Camera Memory
If you want to transfer images from your computer to the camera, install Photo
Transport on your computer from the CD-ROM that comes with the camera.
. To install Photo Transport
1. On the CD-ROM menu screen, select “Photo Transport”.
2. After reading the information about installation conditions and system
requirements for installation in the “Read me” file, install Photo
Transport.
. To transfer images to the camera
2. On your computer, click the following: Start * All Programs *
CASIO * Photo Transport.
This starts up Photo Transport.
3. Drag the file(s) you want to transfer to the [Transfer] button.
4. Follow the instructions that appear on the display to complete the
transfer.
• The details of the instructions that appear on the display and the transferred
images will depend on your Photo Transport setup. For details, click the
[Settings] button or [Help] button and check the setup.
Transfer Data
• Only image files with the following extensions can be transferred to the camera:
jpg, jpeg, jpe, bmp (bmp images are converted to jpeg images automatically when
transferred.)
• Certain types of images may not be able to be transferred.
• You cannot transfer movies to the camera.
Using the Camera with a Computer
Download from Www.Somanuals.com. All Manuals Search And Download.
141
. To transfer computer screen captures to the camera
2. On your computer, click the following: Start * All Programs *
CASIO * Photo Transport.
This starts up Photo Transport.
3. Display the screen whose screen capture you want to transfer.
4. Click the [Capture] button.
5. Draw a boundary around the area you want to capture.
Move your mouse pointer to the upper left corner of the area you want to capture
and then hold down the mouse button. Keeping the mouse button depressed,
drag the pointer down to the lower right corner of the area and then release the
mouse button.
6. Follow the instructions that appear on the display.
This will send an image of the area you selected to the camera.
• The transfer operation converts screen captures to JPEG format.
• The instructions that appear on the display and details about the transferred
images will depend on your Photo Transport setup. For details, click the
[Settings] button or [Help] button and check the setup.
. About settings and help
Click the [Settings] button when you want to change the Photo Transport setup. For
help about operation procedures and troubleshooting, click the Photo Transport
[Help] button.
User Registration
You can perform user registration over the Internet. To do so, of course, you need to
be able to connect to the Internet with your computer.
1. On the CD-ROM menu screen, click the “Register” button.
• This starts up your Web browser and accesses the user registration website.
Follow the instructions that appear on your computer screen to register.
Using the Camera with a Computer
Download from Www.Somanuals.com. All Manuals Search And Download.
142
Using the Camera with a Macintosh
Install the required software in accordance with what version of the Macintosh OS
you are running and what you want to do.
When you want to
do this:
Operating
System Version
See
page:
Install this software:
Save images to your
Macintosh and view
them there manually
OS 9
OS X
Installation not required.
Use commercially available
software.
Save images to your
Macintosh
automatically/
Manage images
OS 9
OS X
Use iPhoto, which comes bundled
with some Macintosh products.
You can playback with QuickTime,
which comes bundled with your
operating system.
Play movies
OS 9 / OS X
Connecting the Camera to Your Computer and Saving Files
IMPORTANT!
• The camera does not support operation with Mac OS 8.6 or earlier, or Mac OS X
10.0. Operation is supported with Mac OS 9, X (10.1, 10.2, 10.3, 10.4, 10.5) only.
Use the standard USB driver that comes with your supported operating system.
. To connect the camera to your computer and save files
1. Turn on the camera and press [MENU].
2. On the “Set Up” tab, select “USB” and then press [6].
3. Use [8] and [2] to select “Mass Storage”, and then press [SET].
Using the Camera with a Computer
Download from Www.Somanuals.com. All Manuals Search And Download.
143
4. Turn off the camera and then use the USB cable that comes with the
camera to connect it to your Macintosh.
USB port
USB cable
Large connector
USB/AV port
Small connector
Terminal
Making sure that the 6 mark on the camera is aligned
with the 4 mark of the USB cable connector, connect
cover
the cable to the camera.
• The camera does not draw power over the USB cable. Check the battery level
before connecting and make sure it is not too low.
• Make sure that you insert the cable connector into the USB/AV port until you
feel it click securely into place. Failure to insert the connector fully can result in
poor communication or malfunction.
• Note that even while the connector is fully inserted, you
still will be able to see the metal part of the connector as
shown in the illustration.
• When connecting the USB cable to a USB port, make
sure you align the connector correctly with the port.
• Your computer may not be able to recognize the camera
if you connect via a USB hub. Always connect directly to the computer’s USB
port.
5. Turn on the camera.
The camera’s back lamp will light green at this time. In this mode, your Macintosh
recognizes the memory card loaded in the camera (or the camera’s built-in
memory if it does not have a memory card loaded) as a drive. The appearance of
the drive icon depends on the Mac OS version you are using.
Using the Camera with a Computer
Download from Www.Somanuals.com. All Manuals Search And Download.
144
6. Double-click the camera’s drive icon.
7. Drag the “DCIM” folder to the folder to which you want to copy it.
8. After the copy operation is complete, drag the drive icon to Trash.
9. On the camera, press [ON/OFF] to turn off the camera. After making
sure that the green back lamp is unlit, disconnect the camera from the
computer.
. To view copied images
1. Double-click the camera’s drive icon.
2. Double-click the “DCIM” folder to open it.
3. Double-click the folder that contains the images you want to view.
4. Double-click the image file you want to view.
• An image that was rotated on the camera will be displayed on your Macintosh
screen in its original (unrotated) orientation.
• Viewing a CS image on a computer will individually display the component
images in the CS group. A CS group cannot be viewed as a CS image on a
computer.
Never use your computer to modify, delete, move, or rename any image files
that are in the camera’s built-in memory or on its memory card.
Doing so can cause problems with the camera’s image management data, which
will make it impossible to play back images on the camera and can drastically alter
remaining memory capacity. Whenever you want to modify, delete, move, or
rename an image, do so only on images that are stored on your computer.
IMPORTANT!
• Never unplug the USB cable, or operate the camera while viewing or storing
images. Doing so can cause data to become corrupted.
Using the Camera with a Computer
Download from Www.Somanuals.com. All Manuals Search And Download.
145
Transferring Images Automatically and Managing Them on
Your Macintosh
If you are running Mac OS X, you can manage snapshots using iPhoto, which comes
bundled with some Macintosh products. If you are running Mac OS 9, you will need to
use commercially available software.
Playing a Movie
You can use QuickTime, which comes bundled with your operating system, to play
back movies on a Macintosh. To play back a movie, first copy it to your Macintosh
and then double-click the movie file.
. Minimum Computer System Requirements for Movie Playback
The minimum system requirements described below are necessary to play back
movies recorded with this camera on a computer.
Operating System : Mac OS X 10.3.9 or higher
Required Software : QuickTime 7 or higher
• The above are recommended system environments. Configuring one of these
environments does not guarantee proper operation.
• Certain settings and other installed software may interfere with proper playback of
movies.
. Movie Playback Precautions
Proper movie playback may not be possible on some Macintosh models. If you
experience problems, try the following.
– Change the movie image quality setting to “STD”.
– Upgrade to the latest version of QuickTime.
– Shut down other applications that are running.
Even if proper playback is not possible on your Macintosh, you can use the AV cable
that comes bundled with the camera to connect to the video input terminal of a TV or
Macintosh and play back movies that way.
IMPORTANT!
• Be sure to move the movie data to the hard disk of your Macintosh before trying to
play it. Proper movie playback may not be possible for data accessed over a
network, from a memory card, etc.
Using the Camera with a Computer
Download from Www.Somanuals.com. All Manuals Search And Download.
146
Viewing User Documentation (PDF Files)
You must have Adobe Reader or Adobe Acrobat Reader installed on your computer
in order to view the contents of a PDF file. If you don’t, go to the Adobe Systems
Incorporated website and install Acrobat Reader.
1. On the CD-ROM, open the “Manual” folder.
2. Open the “Digital Camera” folder and then open the folder for the
language whose user’s guide you want to view.
3. Open the file named “camera_xx.pdf”.
• “xx” is the language code (Example: camera_e.pdf is for English.)
User Registration
Internet registration only is supported. Visit the following CASIO website to register:
http://world.casio.com/qv/register/
Using an Eye-Fi Wireless SD Memory Card to Transfer Images
(Eye-Fi)
Shooting with an Eye-Fi wireless SD memory card loaded in the camera makes it
possible to transfer image data automatically to a computer via wireless LAN.
1. Configure LAN access point, transfer destination and other settings for
the Eye-Fi card in accordance with the instructions that come with the
Eye-Fi card.
2. After configuring settings, load the Eye-Fi card into the camera and
record.
Images you record are sent by wireless LAN to your computer, etc.
• For full details, see the user documentation that comes with the Eye-Fi card.
• Before formatting a new Eye-Fi card to use it for the first time, copy the Eye-Fi
Manager install files to your computer. Do this before formatting the card.
Using the Camera with a Computer
Download from Www.Somanuals.com. All Manuals Search And Download.
147
IMPORTANT!
• Recorded images are transferred over wireless LAN. Do not use the Eye-Fi card or
location where use of wireless communication is limited or prohibited.
• Loading an Eye-Fi card will cause the Eye-Fi indicator
to
appear on the monitor screen. Its transparent or not transparent
appearance indicates the communication status as shown below.
Access point cannot be found or no transferable
image data exists.
Transparent
Not transparent Image transfer in progress
• A communication icon
will appear on the monitor screen while image data
transfer is in progress.
transfer is in progress.
• A confirmation message will appear on the monitor screen if you try to turn off the
camera while image data transfer is in progress. Follow the instructions in the
messages (page 181).
• Transfer of a large number of images can take some time to complete.
• The original images remain on the Eye-Fi card after the image data transfer.
• Recording a movie to an Eye-Fi card may result in movie frames being dropped.
• Proper Eye-Fi card data communication may not be possible due to camera
settings, battery level, or operating conditions.
Using the Camera with a Computer
Download from Www.Somanuals.com. All Manuals Search And Download.
148
Files and Folders
The camera creates a file each time you shoot a snapshot, record a movie, or
perform any other operation that stores data. Files are grouped by storing them in
folders. Each file and folder has its own unique name.
Name and Maximum Number Allowed
Example
File
Each folder can contain up to 9999 files named 26th file name:
CIMG0001 through CIMG9999. The extension
CIMG0026.JPG
on the file name depends on the file type.
Serial number Extension
(4 digits)
Folders
Folders are named from 100CASIO to
100th folder name:
999CASIO.
100CASIO
There can be up to 900 folders in memory.
• BEST SHOT has a scene named “For
YouTube” that optimizes movie settings for
recording movies for upload to YouTube.
Images recorded with the YouTube scene are
stored in a folder named “100YOUTB”.
Serial number (3 digits)
• You can view folder and file names on your computer. For details about how file
• The total number of folders and files allowed depends on the image size and
quality, and capacity of the memory card being used for storage.
Using the Camera with a Computer
Download from Www.Somanuals.com. All Manuals Search And Download.
149
Memory Card Data
The camera stores images you shoot in accordance with the Design Rule for Camera
File System (DCF).
. About DCF
DCF is a standard that makes it possible to view and print images recorded on one
manufacturer’s camera on DCF-compliant devices produced by other manufacturers.
You can transfer DCF-compliant images recorded with another camera to this
camera and view them on this camera’s monitor screen.
. Memory Folder Structure
DCIM Folder
Recording Folder
Image File
DCIM
1
*
100CASIO
CIMG0001.JPG
CIMG0002.AVI
Movie File
1
*
Recording Folder
Recording Folder
101CASIO
102CASIO
1
*
DPOF File Folder
DPOF File
MISC
AUTPRINT.MRK
2
*
SCENE
Snapshot BEST SHOT User Setup Folder
SSBGM
SSBGM001.WAV
SSBGM002.WAV
Background Music Folder
Background Music File
Background Music File
2
*
STARTING.JPG
Startup Image File
*1 The BEST SHOT “For YouTube” scene sets up the camera for recording movies that
are optimized for uploading to YouTube. Images recorded with the “For YouTube”
scene are stored in a folder named “100YOUTB”.
*2 This folder or file can be created in built-in memory only.
Using the Camera with a Computer
Download from Www.Somanuals.com. All Manuals Search And Download.
150
. Supported Image Files
• Image files shot with this camera
• DCF-compliant image files
This camera may not be able to display an image, even if it is DCF-compliant. When
displaying an image recorded on another camera, it may take a long time for the
image to appear on this camera’s monitor screen.
. Built-in Memory and Memory Card Data Handling Precautions
• Whenever copying memory contents to your computer, you should copy the DCIM
folder and all of its contents. A good way to keep track of multiple DCIM folders it to
change their names to dates or something similar after you copy them to your
computer. If you later decided to return a DCIM folder to the camera, however, be
sure to change its name back to DCIM. The camera is designed to recognize only a
root file with the name DCIM. Note the camera also will not be able to recognize the
folders inside the DCIM folder unless they have the names they originally had
when you copied them from the camera to your computer.
• You also can use a PC card adapter or a memory card reader/writer to access
camera files directly from the camera’s memory card.
Using the Camera with a Computer
Download from Www.Somanuals.com. All Manuals Search And Download.
151
Other Settings (Set Up)
This section explains menu items that you can use to configure settings and perform
other operations in both the REC mode and PLAY mode.
Adjusting Monitor Screen Brightness (Screen)
Procedure
[MENU] * Set Up Tab * Screen
With this setting, the camera detects available light levels and
Auto 2/ automatically adjusts the brightness of the monitor screen accordingly.
Auto 1 “Auto 2” changes monitor screen brightness relatively more quickly than
“Auto 1” when surrounding light is bright.
Brightness that is greater than +1, which makes the screen easier to view.
This setting consumes more power.
+2
+1
0
Bright setting for outdoor use, etc. Brightness that is greater than 0.
Normal monitor screen brightness for indoor use, etc.
Turning off Eye-Fi Card Communication (Eye-Fi)
Procedure
[MENU] * Set Up Tab * Eye-Fi
Download from Www.Somanuals.com. All Manuals Search And DOotwhenr lSoeattdin.gs (Set Up)
152
Configuring Camera Sound Settings (Sounds)
Procedure
[MENU] * Set Up Tab * Sounds
Startup
Specifies the startup sound
Sound 1 - 5: Built-in sounds (1 through 5)
Off: Sound off
Half Shutter
Shutter
Operation
Specifies the sound volume. This setting is also used as the
Operation
Play
=
=
Specifies the volume of movie audio output. This volume
setting is not used during video output (from the USB/AV port)
• Setting a volume level of 0 mutes output.
Specifying the File Name Serial Number Generation Rule
(File No.)
Procedure
[MENU] * Set Up Tab * File No.
Use the following procedure to specify the rule that governs generation of the serial
Tells the camera to remember the last used file number. A new file will
be named using the next sequential number, even if files are deleted or
if a blank memory card is loaded. If a memory card is loaded and that
Continue card already has files stored on it and the largest sequential number in
the existing file names is greater than the largest sequential number
remembered by the camera, numbering of new files will start from the
largest sequential number in the memory card file names plus 1.
Restarts the serial number from 0001 whenever all files are deleted or
when the memory card is replaced with a blank one. If a memory card
Reset
is loaded and that card already has files stored on it, numbering of new
files will start from the largest sequential number in the memory card
file names plus 1.
Download from Www.Somanuals.com. All Manuals Search And DOotwhenr lSoeattdin.gs (Set Up)
153
Configuring World Time Settings (World Time)
Procedure
[MENU] * Set Up Tab * World Time
You can use the World Time screen to view the current time in a zone that is different
from your Home City when you go on a trip, etc. World Time displays the current time
in 162 cities in 32 time zones around the globe.
1. Use [8] and [2] to select “World” and then press [6].
• To change the geographic area and city for the time where you normally use
the camera, select “Home”.
2. Use [8] and [2] to select “City” and then press [6].
• To change the “World” setting to summer time, use [8] and [2] to select
“DST” and then select “On”. Summer time is used in some geographical areas
to advance the current time setting by one hour during the summer months.
3. Use [8], [2], [4], and [6] to select the geographic area you want and
then press [SET].
4. Use [8] and [2] to select the city you want and then press [SET].
5. Press [SET].
IMPORTANT!
• Before configuring World Time settings, make sure that the Home City setting is
the place where you live or normally use the camera. If it isn’t, select “Home” on the
screen in step 1 and configure the Home City, date, and time settings as required
Download from Www.Somanuals.com. All Manuals Search And DOotwhenr lSoeattdin.gs (Set Up)
154
Time Stamping Snapshots (Timestamp)
Procedure
[MENU] * Set Up Tab * Timestamp
You can configure the camera to stamp the recording date only, or date and time in
the lower right corner of each snapshot.
• Once date and time information is stamped into a snapshot, it cannot be edited or
deleted.
Example: July 10, 2012, 1:25 p.m.
Date
2012/7/10
Date&Time
Off
2012/7/10 1:25pm
No stamping of date and/or time
• Even if you do not stamp the date and/or time with Timestamp, you can do so later
using the DPOF function or some printing application (page 130).
and the display style settings (page 156).
Setting the Camera’s Clock (Adjust)
Procedure
[MENU] * Set Up Tab * Adjust
[8] [2] Change the setting at the cursor location
[4] [6] Move the cursor between settings
[BS]
Toggles between 12-hour and 24-hour format
When the date and time settings are what you want, select “Apply” and then press
[SET] to apply them.
• You can specify a date from 2001 to 2049.
you set the time and date while the wrong city is selected for your Home City, the
Download from Www.Somanuals.com. All Manuals Search And DOotwhenr lSoeattdin.gs (Set Up)
155
Specifying the Date Style (Date Style)
Procedure
[MENU] * Set Up Tab * Date Style
You can select from among three different styles for the date.
Example: July 10, 2012
YY/MM/DD
DD/MM/YY
MM/DD/YY
12/7/10
10/7/12
7/10/12
YY/MM/DD or MM/DD/YY: MM/DD
DD/MM/YY: DD/MM
Specifying the Display Language (Language)
Procedure
[MENU] * Set Up Tab * Language
. Specify the display language you want.
Select the tab on the right.
Select “Language”.
Select the language you want.
1
1
2
3
23
Download from Www.Somanuals.com. All Manuals Search And DOotwhenr lSoeattdin.gs (Set Up)
156
Configuring Sleep State Settings (Sleep)
Procedure
[MENU] * Set Up Tab * Sleep
This feature turns off the monitor screen whenever no camera operation is performed
for a preset amount of time. Press any button to turn the monitor screen back on.
Trigger Time Settings: 30 sec, 1 min, 2 min, Off (Sleep is disabled while “Off” is
selected.)
• Sleep is disabled under any of the following conditions.
– In the PLAY mode
– While the camera is connected to a computer or other device
– During a slideshow
– During movie recording and playback
– During Move Out CS or Move In CS auto record standby
– When both sleep and Auto Power Off are turned on, Auto Power Off takes
priority.
Configuring Auto Power Off Settings (Auto Power Off)
Procedure
[MENU] * Set Up Tab * Auto Power Off
Auto Power Off turns off the camera whenever no camera operation is performed for
a preset amount of time.
Trigger Time Settings: 2 min, 5 min, 10 min (The trigger time is always 5 minutes in
the PLAY mode.)
• Auto Power Off is disabled under any of the following conditions.
– While the camera is connected to a computer or other device
– During a slideshow
– During CS group playback
– During movie recording and playback
– During Move Out CS or Move In CS auto record standby
Download from Www.Somanuals.com. All Manuals Search And DOotwhenr lSoeattdin.gs (Set Up)
157
Configuring [r] and [p] Settings (REC/PLAY)
Procedure
[MENU] * Set Up Tab * REC/PLAY
Camera turns on whenever [r] (REC) or [p] (PLAY) is
pressed.
Power On
Camera turns on or off whenever [r] (REC) or [p] (PLAY) is
pressed.
Power On/Off
Camera does not turn on or off when [r] (REC) or [p] (PLAY)
is pressed.
Disable
• With “Power On/Off”, the camera turns off when you press [r] (REC) in the REC
mode or [p] (PLAY) in the PLAY mode.
• Change this setting to “Power On” or “Power On/Off” before connecting to a TV for
image viewing.
Configuring USB Protocol Settings (USB)
Procedure
[MENU] * Set Up Tab * USB
You can use the procedure below to select the USB communication protocol, which is
used when exchanging data with a computer, printer, or other external device.
Select this setting when connecting to a computer (pages 134,
143). With this setting, the computer sees the camera as an
external storage device. Use this setting for normal transfer of
Mass Storage
images from the camera to a computer.
PTP
(PictBridge)
Select this setting when connecting to a printer that supports
Download from Www.Somanuals.com. All Manuals Search And DOotwhenr lSoeattdin.gs (Set Up)
158
B
Selecting the Screen Aspect Ratio and Video Output System
(Video Out)
Procedure
[MENU] * Set Up Tab * Video Out
You can use the procedure in this section to select either NTSC or PAL as the video
output system. You can also specify an aspect ratio of 4:3 or 16:9.
NTSC Video system used in Japan, the U.S., and other countries
PAL
Video system used in Europe and other areas
4:3
Normal TV screen aspect ratio
Wide screen aspect ratio
16:9
• Output to a TV is not supported while the camera is in the REC mode.
• When the camera is connected to a TV for movie playback, only movie images are
displayed on the TV screen. The camera’s monitor screen will show on-screen
information only (without any movie image).
• Select the aspect ratio (4:3 or 16:9) that matches the type of TV you plan to use.
Images will not display correctly if you select the wrong aspect ratio.
• Images will not display correctly unless the camera’s video signal output setting
matches the video signal system of the TV or other video equipment.
• Images cannot be displayed correctly on a TV or video equipment that is not NTSC
or PAL.
Configuring a Startup Image (Startup)
Procedure
[MENU] * Set Up Tab * Startup
Display the image you want to use as your startup image and then select “On”.
• The startup image does not appear when you turn on the camera by pressing [p]
(PLAY).
• You can specify a snapshot you recorded as the startup image, or you can use the
special startup image provided in the camera’s built-in memory.
• You can select the first snapshot of a CS group as the startup image. If you want to
select another image within a CS group, you need to first divide up the CS group or
use the CS Frame Edit feature to make a copy of the image outside of the CS
group.
Download from Www.Somanuals.com. All Manuals Search And DOotwhenr lSoeattdin.gs (Set Up)
159
Formatting Built-in Memory or a Memory Card (Format)
Procedure
[MENU] * Set Up Tab * Format
If a memory card is loaded in the camera, this operation will format the memory card.
It will format built-in memory if no memory card is loaded.
• The format operation will delete all contents on the memory card or in built-in
memory. It cannot be undone. Make sure you do not need any data currently on
the card or in built-in memory before you format it.
• Formatting built-in memory will delete the following data.
– Protected images
– BEST SHOT user setups
– Startup screen
• Formatting a memory card will delete the following data.
– Protected images
• Check the battery level before starting a format operation and make sure it is not
too low. Formatting may not be performed correctly and the camera may stop
operating normally if the camera powers down while formatting is in progress.
• Never open the battery cover while formatting is in progress. Doing so can cause
the camera to stop operating normally.
Resetting the Camera to Factory Defaults (Reset)
Procedure
[MENU] * Set Up Tab * Reset
The settings below are not reset.
World Time settings, clock settings, date style, screen language, video output
Download from Www.Somanuals.com. All Manuals Search And DOotwhenr lSoeattdin.gs (Set Up)
160
Configuring Monitor Screen Settings
Turning Display Information On and Off (Info)
Each press of [8] (DISP) will cycle through display settings that display or hide on-
screen information and the control panel. You can configure separate settings for the
REC mode and PLAY mode.
Information on,
Displays setting information and the control panel.
control panel on
Displays setting information and the
control panel, and a histogram (page 161)
on the left side of the display. Also
displays the remaining movie recording
time in place of the remaining snapshot
capacity, as well as a movie image quality icon.
Information on,
control panel on,
histogram on
Histogram
Information off,
control panel off
Hides setting information and the control panel.
• The control panel is not displayed and display information settings cannot be
changed during movie recording.
Using the On-screen Histogram to Check Exposure
(+Histogram)
Displays a histogram on the monitor screen which you can use to
check the exposure of an image before you shoot it. You also can
display the histogram in the PLAY mode for information about the
exposure levels of images.
Histogram
NOTE
• A centered histogram does not necessarily guarantee optimum exposure. The
recorded image may be over-exposed or under-exposed, even though its
histogram is centered.
• Due to the limitations of exposure compensation, you may not be able to achieve
an optimum histogram configuration.
• Use of the flash and certain shooting conditions can cause the histogram to
indicate exposure that is different from the actual exposure of the image when it is
shot.
• The histogram cannot be displayed during high speed movie recording.
Configuring Monitor Screen Settings
Download from Www.Somanuals.com. All Manuals Search And Download.
161
How to Use the Histogram
A histogram is a graph that represents the lightness of an image in terms of the
number of pixels. The vertical axis indicates the number of pixels, while the horizontal
axis indicates lightness. If the histogram appears too lopsided for some reason, you
can use EV shift to move it left or right in order to achieve better balance. Optimum
exposure can be achieved by EV shifting so the graph is as close to the center as
possible. For snapshots, you can even display individual histograms for R (red), G
(green), and B (blue).
Example Histograms
A histogram towards the left side results when the
overall image is dark. A histogram that is too far to
the left may result in “black out” of the dark areas
of an image.
A histogram towards the right side results when
the overall image is light. A histogram that is too
far to the right may result in “white out” of the light
areas of an image.
An overall well-balanced histogram results when
the overall image is at optimal lightness.
Configuring Monitor Screen Settings
Download from Www.Somanuals.com. All Manuals Search And Download.
162
Appendix
Precautions during Use
. Avoid Use While In Motion
• Never use the camera to record or play back images while operating an automobile
or other vehicle, or while walking. Looking at the monitor while in motion creates
the risk of serious accident.
. Flash
• Never use the flash unit in areas where flammable or explosive gas may be
present. Such conditions create the risk of fire and explosion.
• Never fire the flash in the direction of a person operating a motor vehicle. Doing so
can interfere with the driver’s vision and creates the risk of accident.
• Never fire the flash too close to the eyes of the subject. Doing so creates the risk of
loss of eyesight.
. Monitor Screen
• Should the monitor screen ever become cracked, never touch any of the liquid
inside the monitor screen. Doing so creates the risk of skin inflammation.
• Should monitor screen liquid ever get into your mouth, immediately rinse your
mouth out and contact your physician.
• Should monitor screen liquid ever get into your eyes or onto your skin, immediately
rinse with clean water for at least 15 minutes and contact your physician.
. Connections
• Never plug any devices that are not specified for use with this camera into
connectors. Connecting a non-specified device creates the risk of fire and electric
shock.
. Transport
• Never operate the camera inside of an aircraft or anywhere else where operation of
such devices is restricted. Improper use creates the risk of serious accident.
Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
163
. Smoke, abnormal odor, overheating, and other abnormalities
• Continued use of the camera while it is emitting smoke or strange odor, or while it
is overheating creates the risk of fire and electric shock. Immediately perform the
following steps whenever any of the above symptoms are present.
1. Turn off the camera.
2. Remove the battery from the camera, taking care to protect yourself against burn
injury.
3. Contact your dealer or nearest CASIO authorized service center.
. Water and Foreign Matter
• Water, other liquids, or foreign matter (especially metal) getting inside the camera
creates the risk of fire and electric shock. Immediately perform the following steps
whenever any of the above symptoms are present. Particular care is required when
using the camera where it is raining or snowing, near the ocean or other body of
water, or in a bathroom.
1. Turn off the camera.
2. Remove the battery from the camera.
3. Contact your dealer or nearest CASIO authorized service center.
. Dropping and Rough Treatment
• Continued use of the camera after it is damaged by dropping or other rough
treatment creates the risk of fire and electric shock. Immediately perform the
following steps whenever any of the above symptoms are present.
1. Turn off the camera.
2. Remove the battery from the camera.
3. Contact your dealer or nearest CASIO authorized service center.
. Keep Away From Fire
• Never expose the camera to fire, which can cause it to explode and creates the risk
of fire and electric shock.
. Disassembly and Modification
• Never try to take the camera apart or modify it in any way. Doing so creates the risk
of electric shock, burn injury, and other personal injury. Be sure to leave all internal
inspection, maintenance, and repair up to your dealer or nearest CASIO authorized
service center.
Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
164
. Locations To Be Avoided
• Never leave the camera in any of the following types of locations. Doing so creates
the risk of fire and electric shock.
– Areas subject to large amounts of humidity or dust
– Food preparation areas or other locations where oil smoke is present
– Near heaters, on a heated carpet, in areas exposed to direct sunlight, in a closed
vehicle parked in the sun, or other areas subject to very high temperatures
• Never place the camera on an unstable surface, on a high shelf, etc. Doing so can
cause the camera to fall, creating the risk of personal injury.
. Backing Up Important Data
• Always keep backup copies of important data in camera memory by transferring it
to a computer or other storage device. Note that data can be deleted in the case of
camera malfunction, repair, etc.
. Memory Protection
• Whenever replacing the battery, be sure to follow the correct procedure as
described in the documentation that comes with the camera. Incorrectly replacing
the battery can result in corruption or loss of data in camera memory.
. Rechargeable Battery
• Use only the specified charger unit or the specified device to charge the battery.
Attempting to charge the battery by an unauthorized means creates the risk of
battery overheating, fire, and explosion.
• Do not expose or immerse the battery in fresh water or salt water. Doing so can
damage the battery, and cause deterioration of its performance and loss of service
life.
• The battery is intended for use with a CASIO Digital Camera only. Use with any
other device creates the risk of the battery damage, or deterioration of battery
performance and service life.
• Failure to observe any of the following precautions creates the risk of battery
overheating, fire, and explosion.
– Never use or leave the battery near open flame.
– Do not expose the battery to heat or fire.
– Make sure the battery is oriented correctly when it is connected to the charger
unit.
– Never carry or store the battery together with items that can conduct electricity
(necklaces, pencil lead, etc.)
– Never disassemble the battery, pierce it with a needle, or expose it to strong
impact (hit it with a hammer, step on it, etc.), and never apply solder to it. Never
place the battery into a microwave oven, heater, high-pressure generating
device, etc.
• Should you ever notice leakage, strange odor, heat generation, discoloration,
deformation, or any other abnormal condition while using, charging, or storing a
battery, immediately remove it from the camera or charger unit and keep it away
from open flame.
Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
165
• Do not use or leave the battery under direct sunlight, in an automobile parked in the
sun, or in any other area subject to high temperatures. Doing so can damage the
battery, and cause deterioration of its performance and loss of service life.
• If battery charging does not end normally within the specified charging time, stop
charging anyway and contact your local CASIO authorized service center.
Continued charging creates the risk of battery overheating, fire, and explosion.
• Battery fluid can damage your eyes. Should battery fluid get into your eyes
accidentally, immediately rinse them with clean tap water and then consult a
physician.
• Be sure to read the user documentation that comes with the camera and special
charger unit before using or charging the battery.
• If a battery is to be used by young children, make sure that a responsible adult
makes them aware of the precautions and proper handling instructions, and make
sure that they handle the battery correctly.
• Should fluid from a battery accidentally get onto clothing or your skin, immediately
rinse it off with clean tap water. Prolonged contact with battery fluid can cause skin
irritation.
. Battery Life
• Battery continuous operation times provided in this manual represent the
approximate amount of time before the camera turns off due to low battery power
when being powered by the special battery under normal temperature (23°C
(73°F)). They do not guarantee that you will be able to achieve the indicated level
of operation. Actual battery life is greatly affected by ambient temperature, battery
storage conditions, the amount of time spent in storage, etc.
• Leaving the camera on can run down the battery and cause the low battery
warning to appear. Turn off the camera whenever you are not using it.
• The low battery warning indicates that the camera is about to turn off due to low
battery power. Charge the battery as soon as possible. Leaving a low or dead
battery in the camera can lead to battery leakage and data corruption.
Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
166
. Data Error Precautions
Your digital camera is manufactured using precision digital components. Any of the
following creates the risk of corruption of data in camera memory.
– Removing the battery or memory card while the camera is performing some
operation
– Removing the battery or memory card while the back lamp is flashing green after
turning off the camera
– Disconnecting the USB cable while communication is in progress
– Using a battery that is low
– Other abnormal operations
Any of the above conditions can cause an error message to appear on the monitor
. Operating Environment
• Operating Temperature: 0 to 40°C (32 to 104°F)
• Operating Humidity: 10 to 85% (non condensation)
• Do not place the camera in any of the following locations.
– In an area exposed to direct sunlight, or large amounts of moisture, dust, or sand
– Near an air conditioner or in other areas subjected to extreme temperature or
humidity
– Inside of a motor vehicle on a hot day, or in an area subjected to strong vibration
. Condensation
Sudden and extreme temperature changes, such as when the camera is moved from
the outdoors on a cold winter day into a warm room, can cause water droplets called
“condensation” to form on the interior and the exterior of the camera, which creates
the risk of malfunction. To prevent condensation from forming seal the camera in a
plastic bag before changing locations. Then leave the bag sealed to allow the air
inside to naturally change to the same temperature as the air in the new location.
After that, remove the camera from the bag and open the battery cover for a few
hours.
. Lens
• Never apply too much force when cleaning the surface of the lens. Doing so can
scratch the lens surface and cause malfunction.
• You may sometimes notice some distortion in certain types of images, such as a
slight bend in lines that should be straight. This is due to the characteristics of
lenses, and does not indicate malfunction of the camera.
Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
167
. Caring for your camera
• Never touch the lens or flash window with your fingers. Finger smudges, dirt, and
other foreign matter on the lens or flash window can interfere with proper operation
of the camera. Use a blower or other means to keep the lens and flash window free
of dirt and dust, and wipe gently with a soft, dry cloth.
• To clean the camera, wipe it with a soft, dry cloth.
. Old Rechargeable Battery Handling Precautions
• Insulate the positive and negative terminals with tape, etc.
• Do not peel the covering off of the battery.
• Do not try to take the battery apart.
. Charger Unit Handling Precautions
-
0 Never plug the power cord into an outlet whose voltage rating is different from
that marked on the power cord. Doing so creates the risk of fire, malfunction,
and electric shock.
0 Take care to protect the power cord against damage and breaking. Never place
heavy objects onto the power cord, or expose it to intense heat. Doing so can
damage the power cord, creating the risk of fire and electric shock.
0 Never try to modify the power cord, or subject it to severe bending, twisting, or
pulling. Doing so creates the risk of fire, malfunction, and electric shock.
0 Never plug in or unplug the power cord while your hands are wet. Doing so
creates the risk of electric shock.
0 Do not plug the power cord into an outlet or extension cord that is shared by
other devices. Doing so creates the risk of fire, malfunction, and electric shock.
0 Should the power cord ever become damaged (to the point that internal wires
are exposed or cut), immediately contact your original retailer or authorized
CASIO authorized service center to request repair. Continued use of a damaged
power cord creates the risk of fire, malfunction, and electric shock.
• The charger unit becomes slightly warm during charging. This is normal and does
not indicate malfunction.
• Unplug the power cord from the power outlet when you are not using the charger
unit.
• Never use detergent to clean the power cord (especially the plug).
• Never cover the charger unit with a blanket, etc. Doing so creates the risk of fire.
Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
168
. Other Precautions
The camera becomes slightly warm during use. This is normal and does not indicate
malfunction.
. Copyrights
Except for your own personal enjoyment, unauthorized use of use of snapshots or
movies of images whose rights belong to others, without the permission of the right
holder, is forbidden by copyright laws. In some cases, shooting of public
performances, shows, exhibitions, etc. may be restricted entirely, even if it is for your
own personal enjoyment. Regardless of whether such files are purchased by you or
obtained for free, posting them on a website, a file sharing site, or any other Internet
site, or otherwise distributing them to third parties without the permission of the
copyright holder is strictly prohibited by copyright laws and international treaties. For
example, uploading or distributing on the Internet images of TV programs, live
concerts, music videos, etc. that were photographed or recorded by you may infringe
upon the rights of others. Note that CASIO COMPUTER CO., LTD. shall not be held
liable for use of this product in any way that infringes on the copyrights of others or
that violates copyright laws.
The following terms, which are used in this manual, are registered trademarks or
trademarks of their respective owners.
Note that trademark ™ and registered trademark ® are not used within the text of this
manual.
• The SDHC logo is a trademark.
• Microsoft, Windows, Internet Explorer, Windows Media, Windows Vista,
Windows 7, and DirectX are registered trademarks or trademarks of Microsoft
Corporation in the United States and other countries.
• Macintosh, Mac OS, QuickTime, and iPhoto are trademarks of Apple Inc.
• Adobe and Reader are trademarks or registered trademarks in the United States
and other countries of Adobe Systems Incorporated.
• YouTube, the YouTube logo, and “Broadcast Yourself” are trademarks or
registered trademarks of YouTube, LLC.
• EXILIM, Photo Transport, and YouTube Uploader for CASIO are registered
trademarks or trademarks of CASIO COMPUTER CO., LTD.
• All other company or product names mentioned herein may be registered
trademarks or trademarks of their respective companies.
Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
169
Any and all unauthorized commercial copying, distribution, and copying of the
bundled software over a network are prohibited.
This product contains PrKERNELv4 Real-time OS of eSOL
Co., Ltd. Copyright © 2007 eSOL Co., Ltd.
PrKERNELv4 is a registered trademark of eSOL Co., Ltd. in
Japan.
This product’s YouTube upload functionality is included under license from YouTube,
LLC. The presence of YouTube upload functionality in this product is not an
endorsement or recommendation of the product by YouTube, LLC.
Power Supply
Charging
If the [CHARGE] lamp does not light red...
Charging cannot be performed because ambient temperature or the temperature of
the charger is too hot or too cold. Leave the camera in a location whose temperature
is within the range where charging can be performed. When the camera returns to a
temperature where charging can be performed, the [CHARGE] lamp will light red.
If the [CHARGE] lamp flashes red...
The battery is faulty or the battery is loaded in the charger incorrectly. Remove the
battery from the charger and check if its contacts are dirty. If contacts become dirty,
wipe them clean with a dry cloth. When experiencing charging problems, also check
to make sure that the power cord is not disconnected from the power outlet or
charger.
If problems continue to occur after you perform the above steps, it could mean that
the battery is faulty. Contact your nearest CASIO authorized service center.
Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
170
To replace the battery
1. Open the battery cover and
Stopper
remove the current battery.
With the monitor screen side of the
camera facing upwards, slide the
stopper in the direction indicated by
the arrow in the illustration. After the
battery pops out, pull it the rest of the
way out of the camera.
2. Load a new battery.
Battery Precautions
. Precautions during Use
• Operation provided by a battery under cold conditions is always less than operation
under normal temperatures. This is due to the characteristics of the battery, not the
camera.
• Charge the battery in an area where the temperature is within the range of 5°C to
35°C (41°F to 95°F). Outside this temperature range charging can take longer than
normal or even fail.
• Do not tear or remove the battery outer label.
• If a battery provides only very limited operation following a full charge, it probably
means the battery has reached the end of its service life. Replace the battery with a
new one.
. Storage Precautions
• Storing the battery for a long time while it is charged can cause deterioration of
battery characteristics. If you do not plan to use a battery for some time, fully use
up its charge before storing it.
• Always remove the battery from the camera when you are not using it. A battery left
in the camera can discharge and go dead, which will require some time to charge
when you need to use the camera.
• Store batteries in a cool, dry place (20°C (68°F) or lower).
• To prevent over discharging of an unused battery, fully charge it, and then load it in
the camera and fully use up the charge about once every six months.
Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
171
Using the Camera in another Country
. Precautions during Use
• The bundled charger is designed for operation with any power supply in the range
of 100V to 240V AC, 50/60Hz. Note, however, that the shape of the power cord
plug depends on each country or geographic area. Before taking the camera and
charger along on a trip, check with travel agent about the power supply
requirements in your destination(s).
• Do not connect the charger to a power supply through a voltage converter or
similar device. Doing so can lead to malfunction.
. Extra Batteries
• Taking along extra fully charged batteries (NP-40) is recommended while on a trip
in order to avoid not being able to shoot images due to the battery going dead.
Using a Memory Card
memory card.
To replace the memory card
Press the memory card and then release it. This will
cause it to pop out of the memory card slot slightly.
Pull the card out the rest of the way and then insert
another one.
• Never remove a card from the camera while the
back lamp is flashing green. Doing so can cause
the image save operation to fail and even
damage the memory card.
Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
172
. Using a Memory Card
• SD memory cards and SDHC memory cards have a
write protect switch. Use the switch when you need to
guard against accidentally deleting data. Note,
however, if you write protect an SD memory card you
must then turn write protection off whenever you want
to record to it, format it, or delete any of its images.
• If a memory card starts to behave abnormally during
image playback, you can restore normal operation by
Write enabled
Write disabled
multiple memory cards whenever using the camera far away from the home or
office.
• As you record data to and delete data from a memory card a number of times, it
loses its ability to retain data. Because of this, periodic re-formatting of a memory
card is recommended.
• Electrostatic charge, electrical noise, and other phenomena can cause data to
become corrupted or even lost. Make sure that you always back up important data
on other media (CD-R, CD-RW, hard disk, etc.)
. Discarding or Transferring Ownership of a Memory Card or the
Camera
The format and delete functions of the camera do not actually delete files from the
memory card. The original data remains on the card. Note that responsibility for the
data on a memory card lies with you. The following procedures are recommended
whenever you discard a memory card or the camera, or if you transfer ownership to
another party.
• When discarding a memory card, either physically destroy the memory card or use
commercially available data delete software to completely delete the data on the
memory card.
• When transferring ownership of a memory card to another party, use commercially
available data deletion software to completely delete the data on it.
before discarding or transferring ownership of the camera.
Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
173
Computer System Requirements for Bundled Software
Computer system requirements are different for each of the applications. Be sure to
check the requirements for the particular application you are trying to use. Note that
the values provided here are minimum requirements for running each application.
Actual requirements are greater, depending on the number of images and the sizes of
the images being handled.
0Windows
YouTube Uploader for CASIO
Operating System : Windows 7 / Vista / XP (SP2/SP3) / 2000 (SP4)
Other
: Sufficient memory to run the operating system
Computer configuration that enables playback of movies on the
YouTube site
Computer configuration that enables upload of movies to the
YouTube site
Photo Transport 1.0
Operating System
Memory
: Windows Vista / XP / 2000
: At least 64MB
Hard Disk Drive Space : At least 2MB
Adobe Reader 8
Operating System
CPU
: Windows Vista / XP (SP2/SP3) / 2000 (SP4)
: Pentium III Class
Memory
: At least 128MB
Hard Disk Drive Space : At least 180MB
Other
: Internet Explorer 6.0 or higher installed
For details about the minimum system requirements for each software application,
see the “Read me” files on the CASIO Digital Camera Software CD-ROM that comes
bundled with the camera.
Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
174
Reset Initial Default Settings
The tables in this section show the initial default settings that are configured for menu
items (displayed when you press [MENU]) after you reset the camera (page 160).
Menu items depend on whether the camera is in the REC mode or PLAY mode.
• A dash (–) indicates an item whose setting is not reset or an item for which there is
no reset setting.
. REC Mode
“REC” Tab
Focus
Q (Auto Focus)
Quick Shutter
Grid
On
Off
On
On
Self-timer
Anti Shake
AF Area
Off
A Camera AS
Review
U Spot
Icon Help
AF Assist Light
Face Detection
Continuous AF
CS
On
Flash: On / Focus:
Off / AF Area: On /
Metering: Off / CS:
Off / Self-timer:
Off / Flash
Off
Off
Memory
High Speed CS
Intensity: Off /
Save CS Images Normal (Batch)
Digital Zoom: On /
MF Position: Off /
Zoom Position: Off
Digital Zoom
L/R Key
On
Off
“Quality” Tab
T
Quality
(Snapshots)
Flash Intensity
Color Filter
Sharpness
Saturation
Contrast
0
Normal
HD
Off
0
»
Quality
(Movies)
0
»
HS
Speed
240 fps
B Multi
Off
0
Metering
Lighting
Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
175
“Set Up” Tab
Screen
Auto 2
On
Adjust
–
Eye-Fi
Date Style
Language
Sleep
–
Startup: Sound 1 /
Half Shutter:
Sound 1 /
–
1 min
Auto Power Off 5 min
Shutter: Sound 1 /
Operation:
Sound 1 /
Sounds
REC/PLAY
USB
Power On
Mass Storage
=Operation:
...////
/
Video Out
Startup
Format
Reset
–
=Play: ...////
Off
–
File No.
Continue
Home
Off
World Time
Timestamp
–
. PLAY Mode
“PLAY” Tab
Images: All images /
Time: 30 min /
Interval: 3 sec /
Effect: Pattern 1
Protect
–
–
–
–
–
–
–
–
Rotation
Slideshow
Resize
Trimming
Copy
MOTION PRINT 9 frames
Movie Editing
White Balance
Brightness
–
–
–
–
Divide Group
CS Multi Print
CS Frame Edit
DPOF Printing
“Set Up” Tab
• The contents of the “Set Up” tab are the same in the REC mode and PLAY mode.
Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
176
When things don’t go right...
Troubleshooting
Problem
Possible Cause and Recommended Action
Power Supply
Power does not
turn on.
battery goes dead soon after being charged, it means the
battery has reached the end of its life and needs to be
replaced. Purchase a separately available CASIO NP-40
rechargeable lithium ion battery.
The camera
suddenly powers
down.
back on.
3)The camera’s protection function may have activated
because camera temperature is too high. Turn off the camera
and wait until it cools down before trying to use it again.
Power will not turn Remove the battery from the camera and then reload them.
off. Nothing
happens when a
button is pressed.
Image Recording
r
] (REC) to enter
Image is not
1)If the camera is in the PLAY mode, press [
the REC mode.
recorded when the
shutter button is
pressed.
2)If the flash is charging, wait until the charge operation
finishes.
3)If the message “Memory Full” appears, transfer images to
your computer, delete images you no longer need, or use a
different memory card.
Auto Focus does
1)If the lens is dirty, clean it off.
not focus properly. 2)The subject may not be in the center of the focus frame when
you compose the image.
3)The subject you are shooting may not be a type that is
4)You may be moving the camera when shooting. Try shooting
with Anti Shake or use a tripod.
5)You may be pressing the shutter button all the way without
waiting for Auto Focus. Half-press the shutter button and
allow enough time for Auto Focus to focus.
Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
177
Problem
Possible Cause and Recommended Action
The subject is out
of focus in the
The image may not be focused properly. When composing the
image, make sure the subject is located inside the focus frame.
recorded image.
?
The flash does not 1)If
(Flash Off) is selected as the flash mode, change to
fire.
?
3)If a BEST SHOT scene that uses
(Flash Off) is selected,
The ? (Flash Off) The flash unit may be malfunctioning. Contact a CASIO service
icon flashes red on center or your original retailer. Note that though the flash will not
the monitor screen fire, you still can use the camera for non-flash shots.
and the flash does
not fire.
Camera powers
down during Self-
timer countdown.
The battery may be low. Charge the battery.
The monitor screen 1)You may be using Manual Focus and have not focused the
image is out of
focus.
´
2)You may be using
(Macro) for scenery or portraits. Use
)
3)You may be trying to use Auto Focus or
shooting a close-up shot. Use the
(Infinity) when
´
(Macro) for close ups
There is digital
noise in images.
1)Sensitivity may have been increased automatically for a dark
subject, which increases the chance of digital noise. Use a
light or some other means to illuminate the subject.
?
2)You may be attempting to shoot in a dark location with
(Flash Off) selected, which can increase digital noise and
make images appear coarse. In this case, turn on flash (page
44) or use lights for illumination.
cause an increase in digital noise. Use a light or some other
means to illuminate the subject.
Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
178
Problem
Possible Cause and Recommended Action
A recorded image
was not saved.
1)Camera power may have been turned off before the save
operation was complete, which will result in the image not
being saved. If the battery indicator shows
, charge the
2)You may have removed the memory card from the camera
before the save operation was complete, which will result in
the image not being saved. Do not remove the memory card
before the save operation is complete.
Though available
lighting is bright,
Not enough light is reaching the subjects. Change the flash
<
mode setting to
(Flash On) for daylight synchro flash (page
in the image are
dark.
Night shots come
out bad.
at night.
• High Speed Night Scene (for shooting night scenery only)
• High Speed Night Scene and Portrait (for shooting people
against night scenery)
Subjects are too
Sunlight reflected by water, sand, or snow, can cause
<
dark when shooting underexposure of images. Change the flash mode setting to
images in a
seashore or ski
area.
Digital zoom will
not go up to the
maximum value.
The digital zoom setting may be turned off. Turn on digital zoom
The image is out of 1)Focusing may not be possible because the subject is outside
focus during movie
recording.
the focus range. Shoot within the allowable range.
3)Focus is fixed during movie recording.
Playback
The color of the
playback image is
Sunlight or light from another source may be shining directly
into the lens when you are shooting. Position the camera so
different from what sunlight does not shine directly into the lens.
appears on the
monitor screen
when shooting.
Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
179
Problem
Possible Cause and Recommended Action
Images are not
displayed.
This camera cannot display non-DCF images recorded onto a
memory card using another digital camera.
Images cannot be
edited (with White
Balance,
Note that you cannot edit the following types of snapshots.
• Snapshots created using MOTION PRINT
• CS group snapshots
Brightness, Resize, • Movies
Trimming,
Rotation).
• Snapshots recorded with another camera
Other
The wrong date
and time are
The date and time setting is off. Set the correct date and time
displayed, or the
wrong date and
time are being
stored along with
image data.
The messages on
the display are in
the wrong
The wrong display language is selected. Change the display
language.
Images cannot be
transferred over a
USB connection.
1)The USB cable may not be connected securely. Check all
connections.
2)The wrong USB communication protocol is selected. Select
the correct USB communication protocol in accordance with
3)If the camera is not turned on, turn it on.
4)Your computer may not be able to recognize the camera if
you connect via a USB hub. Always connect directly to the
computer’s USB port.
Languageselection 1)You did not configure initial settings after purchasing the
screen appears
when the camera is
turned on.
camera or the camera may have been left with a dead
2)There may be a problem with the camera’s memory data. If
this is the case, perform the reset operation to initialize the
If the language selection screen does not re-appear when you
turn the camera on, it means that the camera’s memory
management data has been restored.
If the same message appears after you turn power back on,
contact your retailer or a CASIO authorized service center.
Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
180
Problem
Possible Cause and Recommended Action
The time and date Load the camera’s battery and reconfigure the time and date
the first time after
purchasing the
for at least 24 hours after configuring time and date settings.
After that, the settings will not be reset if you remove the
camera are reset to battery.
their factory
• If the time and date are reset to their factory default settings
defaults when I
remove the
camera’s battery.
when you remove the battery after it has been loaded for
more than 24 hours, it could mean that the camera’s setting
memory is defective. Contact your retailer or a CASIO
authorized service center.
Display Messages
The camera’s protection function may have activated
because camera temperature is too high. Turn off the
camera and wait until it cools down before trying to use it
again.
ALERT
Battery is low.
Battery power is low.
The camera could not go into auto record standby for some
reason during a Move Out CS or Move In CS operation.
Compose the image again with the boundary aligned
Camera not in
standby.
Re-frame the image.
The image you specified with the slideshow “Images”
Cannot find the file. setting cannot be found. Change the “Images” setting (page
111) and try again.
You are attempting to save a user BEST SHOT scene in
the “SCENE” folder when the folder already contains 999
user scenes.
Cannot register any
more files.
There is something wrong with the memory card. Turn off
the camera, remove the memory card and then reload it
into the camera. If this message re-appears when you turn
the camera back on, format the memory card (page 160).
Card ERROR
IMPORTANT!
• Formatting a memory card deletes all its files. Before
formatting, try transferring recoverable files to a
computer or some other storage device.
Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
181
You are attempting to connect the camera to a printer while
Check connections! the camera’s USB settings are not compatible with the USB
Files could not be
saved because
battery is low.
Battery power is low, so an image file could not be saved.
You are trying to record a file while there are already 9999
files stored in the 999th folder. If you want to record more,
delete files you no longer need (page 29).
Folder cannot be
created.
Images are being
transferred.
Stop transfer and
turn off power?
You are attempting to turn off power while image data is
This message appears and the camera turns off whenever
the lens performs some unexpected operation. If the same
message appears after you turn power back on, contact a
CASIO authorized service center or your original retailer.
LENS ERROR
The Anti Shake unit of the camera may be malfunctioning.
If the same message appears after you turn power back on,
contact your retailer or a CASIO service center.
LENS ERROR 2
Load paper!
The printer ran out of paper while printing.
Memory is full with images you recorded and/or files saved
by editing operations. When shooting with Prerecord CS,
this message indicates that there is not enough memory
capacity to record all of the pre-recorded images. Delete
files you no longer need (page 29).
Memory Full
An error occurred while printing.
• The printer is turned off.
Printing Error
• The printer generated an error, etc.
Image compression could not be performed for some
reason during image data storage. Shoot the image again.
Record Error
Your camera system is corrupted. Contact your retailer or
an authorized CASIO authorized service center.
SYSTEM ERROR
The LOCK switch of the SD or SDHC
memory card loaded in the camera is in the
locked position. You cannot store images to
or delete images from a memory card that is
locked.
LOCK
The card is locked.
Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
182
There are no files in built-in memory or on the memory
card.
There are no files.
There are no
printing images.
Set up DPOF.
There are currently no files specified for printing. Configure
the required DPOF settings (page 127).
There is no image to The setup you are trying to save is for an image that cannot
register.
be saved as a user BEST SHOT scene.
This card is not
formatted.
The memory card loaded in the camera is not formatted.
Format the memory card (page 160).
This file cannot be
played.
The file you are trying to access is corrupted or is a type
that cannot be displayed by this camera.
• You attempted to copy images from built-in memory to a
memory card while there is no memory card loaded in
• You attempted to divide up a CS group while a file that is
This function cannot
be used.
Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
183
Number of Snapshots/Movie Recording Time
Snapshot
Built-in Memory
Approximate
SD Memory Card
(1GB*2) Snapshot
Recording
Image Size
(Pixels)
(Approx. 85.9MB*1
Snapshot
)
Image Quality
Image File
Size
Recording Capacity
Capacity
10M
(3648 2736)
Fine
Normal
Economy
Fine
6.4 MB
13
25
151
x
3.38 MB
2.27 MB
5.6 MB
2.97 MB
2.0 MB
4.59 MB
2.46 MB
1.67 MB
5.66 MB
3.0 MB
2.02 MB
4.3 MB
2.31 MB
1.67 MB
2.5 MB
1.4 MB
1.0 MB
1.36 MB
890 KB
570 KB
430 KB
290 KB
240 KB
286
425
172
325
482
210
392
577
170
322
477
224
418
577
386
689
964
709
1083
1691
2241
3323
4015
38
3:2
15
x
(3648 2432)
Normal
Economy
Fine
29
43
16:9
(3648 2048)
19
x
Normal
Economy
Fine
35
51
9M
15
x
(3456 2592)
Normal
Economy
Fine
29
42
7M
20
x
(3072 2304)
Normal
Economy
Fine
37
51
4M
34
x
(2304 1728)
Normal
Economy
Fine
61
85
2M
62
x
(1600 1200)
Normal
Economy
Fine
95
148
196
290
351
VGA
(640 480)
x
Normal
Economy
Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
184
Movies
Built-in Memory
SD Memory Card
(1GB*2) Movie
Recording
File Size
of
1-minute
Movie
Movie
Mode
Image Quality
(Pixels) / (Audio)
Approximate Data
Rate (Frame Rate)
(Approx.85.9MB*1
)
Movie Recording
Capacity
Capacity
x
HD (1280 720)
30 Megabits/second
(30 frames/second)
4 minutes
22 seconds
23 seconds
225 MB
75 MB
(Monaural)
HD/STD
x
STD (640 480)
10 Megabits/second
(30 frames/second)
1 minute
10 seconds
12 minutes
57 seconds
(Monaural)
x
120 fps (640 480) 50 Megabits/second
2 minutes
38 seconds
14 seconds
14 seconds
14 seconds
28 seconds
375 MB
375 MB
375 MB
187.5 MB
(No audio)
(120 frames/second)
x
240 fps (448 336) 50 Megabits/second
2 minutes
38 seconds
(No audio) (240 frames/second)
x
420 fps (224 168) 50 Megabits/second
(No audio) (420 frames/second)
2 minutes
38 seconds
x
1000 fps (224 64) 25 Megabits/second
5 minutes
14 seconds
(No audio)
(1000 frames/second)
HS
30-120 fps
(640 480)
(Audio recording at
30 fps only)
12.5 Megabits/second
(30 frames/second)
50 Megabits/second
(120 frames/second)
x
10 minutes
56 seconds*3
93.7 MB*3
46.8 MB*3
24 seconds*3
30-240 fps
(448 336)
(Audio recording at
30 fps only)
6.25 Megabits/second
(30 frames/second)
50 Megabits/second
(240 frames/second)
x
1 minute
20 minutes
51 seconds*3
30 seconds*3
Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
185
Built-in Memory
(Approx.
SD Memory
Card
(Maximum
recording time
per recording)
Movie
Mode
Image Quality
(Pixels) / (Audio)
Maximum
File Size
Approximate Data
Rate (Frame Rate)
85.9MB*1) Movie
Recording
Capacity
YouTube (HS120)
(640 480)
(No audio)
50 Megabits/second
(120 frames/second)
2 minutes
30 seconds
x
14 seconds
14 seconds
14 seconds
18 seconds
YouTube (HS240)
50 Megabits/second
(240 frames/second)
1 minute
15 seconds
x
(448 336)
(No audio)
YouTube (HS420)
50 Megabits/second
(420 frames/second)
x
(224 168)
42 seconds
18 seconds
(No audio)
YouTube (HS1000)
25 Megabits/second
(1000 frames/second)
x
(224 64)
Maximum
Movie Size:
1024 MB
(or
(No audio)
YouTube
Capture
Mode
YouTube (HS30-120)
12.5 Megabits/second
(30 frames/second)
50 Megabits/second
(120 frames/second)
x
(640 480)
56 seconds*3
10 minutes*3
10 minutes*3
(Audio recording at
30 fps only)
10 minutes)
YouTube (HS30-240)
6.25 Megabits/second
(30 frames/second)
50 Megabits/second
(240 frames/second)
x
(448 336)
1 minute
(Audio recording at
30 fps only)
51 seconds*3
YouTube (HD)
(1280 720)
(Monaural)
30 Megabits/second
(30 frames/second)
4 minutes
22 seconds
x
23 seconds
YouTube (STD)
(640 480)
(Monaural)
10 Megabits/second
(30 frames/second)
1 minute
10 seconds
x
10 minutes
Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
186
*1 Built-in memory capacity after formatting
*2 The above values are based on use of a PRO HIGH SPEED SD memory card
(Panasonic Corporation). The number of images you can save depends on the type of
memory card you are using.
*3 Recordable time when the entire movie is recorded at 30 fps. Recording time is shorter
if the 30 fps frame rate is switched to 120 fps or 240 fps during recording.
• Snapshot and movie recording capacity values are approximate and intended for
reference only. Actual capacity depends on image contents.
• File size and data rate values are approximate and intended for reference only. Actual
values depend on the type of image being shot.
• When using a memory card with a different capacity, calculate the number of images as a
percentage of 1GB.
• The time it takes to play back a high speed movie will be different from the time it takes to
record it. If you record a 240 fps high speed movie for 10 seconds, for example, it will
take 80 seconds to play it back.
• Each movie can be up to 10 minutes long. Movie recording stops automatically after
10 minutes of recording.
Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
187
Specifications
File Format
Snapshots:
JPEG (Exif Version 2.2); DCF 1.0 standard; DPOF compliant
Movies:
Motion JPEG AVI, IMA-ADPCM audio (monaural)
Recording Media
Built-in Memory (Image Storage Area: 85.9MB)
SD/SDHC
Recorded Image Sizes Snapshot:
10M (3648 2736), 3:2 (3648 2432), 16:9 (3648 2048),
x
x
x
x
x
x
9M (3456 2592), 7M (3072 2304), 4M (2304 1728),
x
x
2M (1600 1200), VGA (640 480)
Movies:
HD (1280 720 30 fps), HS120 (640 480 120 fps),
x
x
x
x
HS240 (448 336 240 fps), HS420 (224 168 420 fps),
HS1000 (224 64 1000 fps), HS30-120 (640 480 30-120 fps
x
x
x
switchable), HS30-240 (448 336 30-240 fps switchable),
x
STD (640 480 30 fps)
Image Deletion
1 file; all files
CS group, Individual images within a CS group (with memory
protection feature)
Effective Pixels
Imaging Element
10.1 Megapixels
Size: 1/2.3-inch square pixel high-speed CMOS
Total Pixels: 10.62 Megapixels
Lens/Focal Distance
(Snapshot)
F3.6 (W) to 4.5 (T) f = 6.42 to 32.1 mm
(equivalent to 37 to 185 mm in 35 mm format)
9 lenses in 7 groups, including aspherical lens.
Zoom
5X optical zoom, 4X digital zoom (20X in combination with
optical zoom)
28.5X maximum HD Zoom (in combination with optical zoom,
VGA size)
Focusing
Contrast Detection Auto Focus
• Focus Modes:
Auto Focus, Macro Focus, Pan Focus, Infinity, Manual Focus
• AF Area:
Spot, Free, Tracking; with AF assist light
9
9
) (Wide Angle)
Approximate Focus
Range (Snapshot)
(From Lens Surface)
Auto Focus: 3 cm to
(1.2" to
Macro Focus: 3 cm to 50 cm (1.2" to 19.7") (Wide Angle)
9
Infinity:
Manual Focus: 3 cm to
* Range is affected by optical zoom.
(Wide Angle)
9
9
) (Wide Angle)
(1.2" to
Metering
Multi-pattern, center weighted, and spot by imaging element
Exposure Control
Program AE, Aperture Priority AE, Shutter Speed Priority AE,
Manual Exposure
Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
188
Exposure
–2.0 EV to +2.0 EV (in 1/3EV steps)
Compensation
Shutter
CMOS electronic shutter, mechanical shutter
Shutter Speed
Snapshot (Auto): 1 to 1/1000 second
Snapshot (Aperture Priority AE): 1 to 1/1000 second
Snapshot (Shutter Speed Priority AE): 30 to 1/1000 second
Snapshot (Manual Exposure): 30 to 1/1000 second
* May differ due to the camera setup.
* 1/40000-second shutter speed is possible only with High
speed Continuous Shutter, shutter speed priority AE or
manual exposure.
Aperture Value
White Balance
F3.6 (W) to F8.5 (W) (When used with ND filter); aperture
changed by optical zoom or recording mode
Auto, Daylight, Overcast, Shade, Day White Fluorescent,
Daylight Fluorescent, Tungsten, Manual WB
Sensitivity
Snapshots:
(Standard Output
Sensitivity)
Auto, ISO 100, ISO 200, ISO 400, ISO 800, ISO 1600,
ISO 3200 equivalent
Movies:
Auto (High Speed Movie when Manual Exposure mode:
ISO 100, ISO 200, ISO 400, ISO 800, ISO 1600, ISO 3200)
Self-timer
Approximate Trigger Times:
10 seconds, 2 seconds, Triple Self-timer
(Trigger time setting depends on CS mode being used.
Available settings depend on the REC mode being used.)
Flash Modes
Auto, Off, On, Red-eye reduction
Flash Range
(ISO Sensitivity: Auto)
0.1 m*2 to 3.2 m (0.3'*2 to 10.5') (Wide Angle)
0.6 m to 2.5 m (2.0' to 8.2') (Telephoto)
*1 Range is affected by optical zoom.
*2 Macro Focus
1
*
Flash Intensity
Adjustment
–2, –1, 0, +1, +2
Flash Charging Time Approximately 8 seconds maximum
Movie Recording
30 lx (HD/STD movie)
Minimum Illumination
Recording
Snapshot, Normal Speed Continuous Shutter, High Speed
Continuous Shutter, Prerecord (Continuous Shutter), Slow
Motion View, BEST SHOT, Face detection, High speed movie
(For “30-120 fps” and “30-240 fps”, audio recording supported
during 30 fps recording only), HD Movie, STD Movie, Prerecord
(Movie), YouTube Capture Mode, CMOS shift image stabilization
Monitor Screen
Viewfinder
2.7-inch TFT color LCD (Super Clear LCD)
230,400 (960 240) dots
x
Monitor Screen
Timekeeping
Functions
Built-in quartz digital clock
Date and Time: Recorded with image data
Auto Calendar: To 2049
Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
189
C
World Time
162 cities in 32 time zones
City name, date, time, summer time
Input/Output
Terminals
USB/AV port, Hi-Speed USB compatible
Microphone
Speaker
Monaural
Monaural
x
Power Requirements Rechargeable lithium ion battery (NP-40)
1
Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
190
Approximate Battery Life
All of the values provided below represent the approximate amount of time under
normal temperature (23°C (73°F)) before the camera turns off. These values are not
guaranteed. Low temperatures shorten battery life.
Number of Shots (CIPA) (Operating Time)*1
Continuous Playback (Snapshots)*2
300 shots
3 hours 20 minutes
Approximate continuous movie recording time
(High speed movie)*3
2 hours
Approximate continuous movie recording time (HD Movie)*3 2 hours 20 minutes
• Battery: NP-40 (Rated Capacity: 1300 mAh)
• Recording Medium: 1GB SD memory card (PRO HIGH SPEED (Panasonic
Corporation))
• Measurement Conditions
*1 Approximate number of shots (CIPA) (Operating Time)
In accordance with CIPA (Camera and Imaging Products Association) standards
Normal temperature (23°C (73°F)), monitor on, zoom operation between full wide and
full telephoto every 30 seconds, during which two images are shot with flash; power
turned off and back on every time 10 images are shot.
*2 Approximate playback time
Standard temperature (23°C (73°F)), one-image scroll approximately every 10 seconds
*3 Approximate time using a 16GB SDHC memory card for a repeated cycle of 10 minutes
recording followed by deletion of the recorded file.
• The above values are based a new battery, starting from a full charge. Repeated
charging shortens battery life.
• Frequency of flash, zoom, High Speed Continuous Shutter, and Auto Focus usage,
and the time the camera is on greatly affects recording time and number of shots
values.
Power Consumption
Dimensions
3.7 V DC, Approximately 4.0 W
x
x
99.8 (W) 58.5 (H) 28.8 (D) mm
x
x
(3.9" (W) 2.3" (H) 1.13" (D))
(22.6 mm (0.89") thick excluding lens)
Weight
181 g (6.4 oz) (including battery and memory card)
145 g (5.1 oz) (excluding battery and memory card)
Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
191
B
. Rechargeable lithium ion battery (NP-40)
Rated Voltage
3.7 V
Rated Capacitance
Operating Temperature
Dimensions
1300 mAh
0 to 40°C (32 to 104°F)
x
x
38.5 (W) 38.0 (H) 9.3 (D) mm
x
x
(1.52" (W) 1.50" (H) 0.37" (D))
Weight
Approximately 34 g (1.2 oz)
. Charger unit (BC-31L)
Input Power
100 to 240 V AC, 80 mA, 50/60 Hz
4.2 V DC, 600 mA
Output Power
Operating Temperature
Supported Battery Type
Charging Time
5 to 35°C (41 to 95°F)
Rechargeable lithium ion battery (NP-40)
150 minutes
x
x
Dimensions
55 (W) 20 (H) 86 (D) mm
x
x
(2.2" (W) 0.79" (H) 3.4" (D)) (excluding projections)
Weight
Approximately 58 g (2.0 oz)
• Power cord precautions for use in Singapore
The power cord set is not supplied. The power cord used must comply with
relevant national and/or international standards.
Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
192
CASIO COMPUTER CO.,LTD.
6-2, Hon-machi 1-chome
Shibuya-ku, Tokyo 151-8543, Japan
M10
MA1002-C
Download from Www.Somanuals.com. All Manuals Search And Download.
|