MA0308-EA
Operation Guide DQR-100
Main unit
Sub-unit
1
A
C
B
°C/ °F
RESET
SNZ
ON
OFF
SNZ
ON
OFF
5
ALM
ALM
TEMP.
MAX/MIN
CLEAR
°C/ °F
RESET
RESET
SET
)
UP(+)
–
(
N
W
O
D
TEMP.
MAX/MIN
CLEAR
9
8
7
4
3
0
6
RESET
SET
)
UP(+)
–
(
N
OW
D
2
• A sticker is affixed to the glass of this clock when you purchase it. Be sure to remove the sticker before using the
clock.
• Depending on the clock model, the configuration of your clock may differ somewhat from that shown in the
illustration.
2
Alarm Off
Current time
(Hour, minutes, seconds)
Alarm On
Snooze on indicator
Day of the week
Alarm on
indicator
PM indicator
Alarm time
DATE (month – date)
Wave OK indicator
Antenna Icon
1
Current Tempreture
(INDOOR)
Current Temperature
(OUTDOOR)
• In locations subject to radio frequency interference, the product may malfunction and require you to reset the
product.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Guide DQR-100
Setting the Time and Date Manually
USING THE ALARM
• When using the clock in an area that is outside of the range of the transmitter in Mainflingen or in an area where
signal reception is impossible for some reason, you need to manually adjust the time as required.
1. Press the SET button (3) to cycle through the setting screens as shown below.
The alarm sounds and the light turns on when the alarm time you set is reached. You can also use the Alarm
Mode selector (5) to select the snooze alarm feature.
Setting the Alarm Time
Normal Timekeeping Screen
Use the Alarm Time Set buttons (2) to set the alarm time.
Pressing the Alarm Time Set buttons (2) causes the alarm time to appear in place of the date on the display.
TEMP
.
CLEAR
MAX/MIN
Press to change the
alarm time setting (+).
Press to change the
alarm time setting (
—
).
RESET
SET
)
–
UP(+)
DOWN(
Year Setting Screen
12-hour/24-hour Timekeeping Screen
• Holding down + or – changes the digits at high speed.
Turning the Alarm On and Off
Use the Alarm Mode selector (5) on the side of the clock to turn the alarm on and off, and to select the snooze
feature.
Alarm Mode selector
SNZ
Description
The alarm sounds at the preset time for one minute, and seven more
times every five minutes thereafter. Even if you stop the alarm sound
by pressing the SNOOZE/LIGHT button (1), the alarm operation is
performed again five minutes later.
( )
Month and Day Setting Screen
Time Setting Screen
• The indicator
flashes on the display to indicate that the
snooze feature is activated.
ALM ON
The alarm sounds at the preset time for one minute.
( )
ALM OFF
The alarm does not sound.
2. While the screen you want is on the display, use the Alarm Time Set buttons (2) to change the digits that are
flashing.
• The alarm time appears in place of the date on the display whenever the Alarm Mode selector (5) is set to ON
or SNZ.
• The light also turns on for the first four seconds that the alarm sounds.
TEMP
MAX/MIN
.
CLEAR
Press + to increase
the flashing digits.
Press
—
to decrease
• The alarm sound changes over four levels as it sounds.
the flashing digits.
RESET
SET
)
–
UP(+)
DOWN(
Stopping the Alarm
• When alarm is sounding, press the SNOOZE/LIGHT button (1) to stop it. When the snooze feature is turned
on, the alarm will sound again in about five minutes.
• Holding down + or – changes the flashing digits at high speed.
• You can set the year in the range of 2000 to 2039. The day of the week is set automatically in accordance with
the date setting.
• Pressing + or – while the Time Setting Screen is on the display causes the seconds count to be reset to 00.
• Each press of + or – while the 12-hour/24-hour Timekeeping Screen is on the display toggles between 12-hour
and 24-hour timekeeping.
• To turn off the snooze feature, slide the Alarm Mode selector (5) to OFF.
USING THE LIGHT
Pressing the SNOOZE/LIGHT button (1) turns on the light and illuminates the display for easy reading in the
dark.
3. After making the settings you want, use the SET button (3) to display the Normal Timekeeping Screen.
• The clock automatically returns to the Normal Timekeeping Screen if you leave a setting screen on the display for
about three minutes without performing any operation.
Important!
• Overuse of the light can shorten battery life.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Guide DQR-100
BATTERY REPLACEMENT
Low Battery Warning
High Temperature and Low Temperature Memory
• The following data is stored in memory automatically.
Main unit high temperature and low temperature
Sub-unit high temperature and low temperature
A
indicator appears on the display to let you know when battery power is low. Replace the batteries as soon
as possible.
Note that the
indicator appears on both the main unit and sub-unit when sub-unit battery power goes low.
To replace main unit batteries
Replace batteries whenever the display of the clock becomes dim and difficult to read.
1. Open the battery compartment cover as shown in the illustration.
2. Remove all of the old batteries.
3. Load a full set of new batteries. Make sure that their positive (+) and negative (–) ends face in the correct
directions. If you load batteries incorrectly, they can burst and damage the clock.
4. Replace the battery compartment cover.
Current temperature
5. Press the RESET button (6). Be sure to press the RESET button (6) after replacing batteries.
To replace sub-unit batteries
1. Rotate the battery compartment cover from LOCK to OPEN.
2. Remove both old batteries.
MAX/MIN TEMP. button (7)
3. Load new batteries. Make sure that their positive (+) and negative (–) ends face in the correct directions. If you
load batteries incorrectly, they can burst and damage the clock.
4. Replace the battery compartment cover.
5. Press the RESET button (B). Be sure to press the RESET button (B) after replacing batteries.
6. Press the RE-SYNC button (0).
Main unit high temperature and low temperature
Battery precautions
• Keep batteries out of the reach of small children. If a battery is accidentally swallowed, contact your physician
immediately.
• Be sure to load the batteries with their positive (+) and negative (–) ends facing correctly.
• Never mix old and new batteries, or batteries of different brands.
• Never charge the batteries that come with the clock.
• Should batteries ever leak while in the clock, wipe out the fluid with a cloth, taking care not to let any get onto
your skin.
Sub-unit high temperature and low temperature
• Replace the batteries at least once a year, even if the current batteries are working properly.
• The batteries that come with the clock lose some of their power during transport and storage.
THERMOMETER FUNCTIONS
Both the main unit and the sub-unit are equipped with their own temperature sensors. Temperature data measured
by the sub-unit is sent by wireless transfer to the main unit. This makes it possible to view both the indoor and
outdoor temperature on the main unit display.
• To clear the high temperature and low temperature data memory, press the CLEAR button (8).
New data starts to be stored after memory is cleared.
Temperature Measurements
• Both the main unit and the sub-unit take temperature measurements every 16 seconds.
• The temperature display shows “LO” for temperatures below –50°C (–58°F) and “HI” for temperatures above
70°C (158°F).
• Though temperature readings are displayed up to 0°C (32°F) and greater than 41°C (105°F), note that such
readings are actually outside the guaranteed temperature range of this clock.
Switching between Celsius and Fahrenheit
• Push the °C/ °F button (9) to select either Celsius (°C) or Fahrenheit (°F).
Celsius (°C)
Fahrenheit (°F)
CLEAR button (8)
Main unit
(INDOOR)
°C
°C
°F
°F
°C/ °F button (9)
Sub-unit
(OUTDOOR)
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Guide DQR-100
USING THE SUB-UNIT
Data Transfer from the Sub-unit
• Data is transferred from the sub-unit to the main unit every three minutes.
• The sub-unit is able to send data to the main unit up to an unobstructed distance of about 30 meters.
• The data receive status is indicated on the display of the main unit by the icons shown below.
Receive successful
Receive unsuccessful
• If a receive operation is not successful for some reason, the display of the main unit shows dashes (–) in place of
the sub-unit temperature value.
• If you experience problems with data transfer, press the RE-SYNC button (0) to synchronize the two units. If
this does not eliminate the problem, try changing the positions or orientations of the main unit and sub-unit.
Switching between Celsius and Fahrenheit
• Push the °C/ °F button (A) to toggle between Celsius (°C) and Fahrenheit (°F).
Celsius (°C)
Fahrenheit (°F)
°C/ °F button (A)
Location
• Place the sub-unit in a location where it will not be exposed to rain, direct sunlight, or other elements.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
|