CONTENTS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
INTRODUCTION
mOUNTINg RECOmmENDATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
fAN INSTALLATION
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
CONTROL fEATURES:
REmOTE OpERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
TROUbLESHOOTINg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
READ AND SAVE THESE INSTRUCTIONS
SAFETY FIRST
Safety and the proper operation of your Casablanca fan both require a thorough knowledge of the product
and proper installation; therefore, before attempting to install and operate your Casablanca fan, read this
owner’s manual completely and carefully. Retain this manual for future reference.
CAUTIon: To avoid possible electrical shock, make certain that electricity is turned
off at the circuit breaker or fuse box before attempting any installation procedure.
BEFORE YOU START
• This fan is designed to be installed on an existing electrical outlet box. The outlet box must be UL Listed for
ceiling fan installations, if it is not, a new box must be installed. Casablanca extension poles are available for
sloped or high ceiling installations.
• This ceiling fan requires a grounded electrical supply of 120 VAC, 60 Hz and a minimum 15 amp circuit. The
maximum current requirement for the fan with light fixture is 3.8 amps. The fan uses about 1 amp or 100 watts.
Maximum light current is 1 amp or 100 watts of lighting.
• Where wire nuts are employed, be sure all bare wires are within the connectors. When installing the canopy
hatch, make sure all wires are within the canopy and that no wires are being pinched.
For best performance and for your warranty to be valid,
use only genuine Casablanca blades, light fixtures, and accessories.
SAFE USE
•
•
The blades in each pack are matched for equal
fUSE BoX
weight to assure smooth fan operation. If (REmovE fUSE foR ThE
CIRCUIT yoU wIll BE
woRKIng on)
more than one fan is being installed, be careful
not to mix blades from different cartons.
Inspect the contents of your carton for possible
shipping or handling damage and report any
such damage directly to your authorized
Casablanca dealer.
18"
64”
•
•
It is always a good idea to have an assistant to
help with the installation.
When cleaning, painting, or working near
your fan, be very careful of the fan and blades.
Always turn the power OFF to the ceiling fan
before servicing it, working on it, or replacing
light bulbs.
84”
CIRCUIT BREAKER
(TRIp BREAKER foR ThE
CIRCUIT yoU wIll BE
woRKIng on)
•
Never insert anything into the path of the fan
blades while the fan is in operation.
•
•
Never install a fan over a pool or spa.
Never operate a fan that has been damaged in
any way. Contact Casablanca Fan Company
by calling toll free 1-888-227-2178, or contact
your local authorized Casablanca dealer for
assistance in obtaining service.
PN C1043001 AT1208
1
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Mo d e n a II
INSTALLATION INSTRUCTIONS
IMPORTANT! Leave the fan in the carton until you are ready to hang the fan.
CEILING HARDWARE
1″ x 8-32 ROUND
HEAD SCREWS (2)
WIRE NUT (4)
fLAT WASHER (2)
LAg SCREW AND WASHER
CROSSbAR
mOUNTINg
(1)
bRACKET
GETTING STARTED
Installing a New Ceiling Fixture Outlet Box
After turning the power OFF at its source (either circuit
If you do not have an existing fixture located where you breaker or fuse box), lower the old fixture and disconnect
wish to place your Casablanca fan, an approved ceiling the wiring. Check the ceiling fixture outlet box to be sure
fixture outlet box must be installed and wired.
that it is marked ‘Approved for ceiling fan mounting’.
If it is not, a new box must be installed.
Warning: To reduce the risk of fire, electrical
shock, or personal injury, mount to outlet box
marked acceptable for ceiling fan support using
the mounting hardware provided with the outlet
box. Using Existing Ceiling Fixture Outlet Box
CROSSBAR MOUNTING BRACKET INSTALLATION
JOIST
Proceed with installation as follows:
Step 1. To install the crossbar mounting bracket, route
the outlet box wires along side of the crossbar mounting
bracket. Attach the crossbar mounting bracket to the
outlet box with the set of two round-head screws and
washers. Use caution when installing the screws and
washers. Do not pinch the outlet box wires in the wash-
ers. Tighten the screws firmly by hand only, being careful
not to bend the bracket by over tightening.
CEILINg
WIRINg
CEILINg fIxTURE
OUTLET bOx
(CEILINg fAN
RATED)
CAUTION: To reduce the risk
of personal injury, use only the
mounting hardware provided
with the approved outlet box to
install the crossbar mounting
bracket.
gREEN
gROUND
WIRE
CROSSbAR
mOUNTINg
bRACKET
(RIDgE SIDE
DOWN)
Step 2. To install the lag screw, slide the remaining
washer onto the lag screw. Pass the lag screw through
the center hole in the crossbar mounting bracket. Se-
cure the lag screw into the guide hole, tightening until
the ceiling fixture outlet box is firmly mounted to the
support beam.
WASHERS
(2)
1” x 8-32
ROUND-HEAD
SCREWS (2)
LAg SCREW
AND
WASHER (1)
3
Download from Www.Somanuals.com. All Manuals Search And Download.
CANOPY HARDWARE
CANOpy HATCH
CANOpy
SCREW (4)
CANOpy LOCK
WASHER (4)
pHILLIpS
SCREWDRIVER
CANOpy
CANOPY INSTALLATION
Step 3. Attach the canopy to the crossbar mounting
bracket with three of the 8-32 x 21/2″ long canopy
screws and canopy lock washers. Tighten the screw
firmly by hand only.
note: On sloped ceilings, align
the canopy opening towards the
top or room peak.
CROSSbAR
mOUNTINg
bRACKET
CANOpy
CANOpy
LOCK
WASHER
perma•lock™ hardware
ALLEN SET
SCREW
¼-20
(pRE-INSTALLED)
3.18mm
ALLEN WRENCH
DOWNROD & bALL
ASSEmbLy
4
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Mo d e n a II
FAN PREPARATION
gROUND
WIRE
Prepare for fan installation as follows:
Step 4. Route the wires from the motor through the
Perma•Lock™ downrod and ball assembly.
mOTOR WIRES
Tip: The downrod has a tapered
thread that is designed to lock com-
pletely when correctly installed.
DOWNROD
& bALL
ASSEmbLy
Step 5. Using the provided allen wrench, loosen the set
screw several turns to allow installation of the downrod.
Thread the downrod into the motor coupling until it stops
turning, this will take at least four and a half full turns.
TApERED
THREAD
mOTOR
COUpLINg
ALLEN
SET SCREW
Step 6. Securely tighten the set screw with the provided
allen wrench to ensure safe operation of your fan.
CAUTION: Failure to fully lock in the downrod before
securely tightening the allen set screw may cause
the fan to separate from the downrod during normal
operation!
WARNING! DO NOT REMOVE THIS LABEL AND TAMPER
WITH ANTI-ROTATION BOTTOM SET SCREW! Unscrew-
ing the bottom set screw may cause fan to separate
from the motor shaft during normal fan operation
and may cause injuries!
BLADE INSTALLATION
SCREW (3 pER bLADE)
bLADE mEDALLION
bLADES
(Set of 5)
(5)
Step 7. Take one blade and align it onto the blade iron of
the fan. There is only one way it will fit. Align the blade
medallion on to the blade and install the 3 screws per
blade. Secure by hand only, do not use a power tool.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
HANGING THE FAN
Step 8. To hang the fan body in the
canopy, hold the fan body firmly
and insert the ball into the canopy
opening. Check that no wires were
pinched. Rotate the fan body until the
slot in the nylon ball fits into the pin
opposite the canopy opening.
bALL
NOTE: The fan weight is 28 pounds.
SLOT
pIN
CANOPY ELECTRICAL CONNECTIONS
Step 9a. Attach the fan wires to the ceiling fixture
outlet box wiring by twisting the bare ends of the wires
together and then securing with a wire nut. Test that the
connection is secure by pulling on the wire nut. Connect
in this order:
2 bLACK WIRES
Step 9b. Wiring Connections
• GREEN leads from mounting plate and fan to
GROUND conductor of power source. Secure with
wire nut.
2 WHITE WIRES
• WHITE wire from fan to white NEUTRAL wire in
ceiling fixture outlet box. Secure with wire nut.
• BLACK power wire from fan to BLACK power wire in
ceiling outlet box. Secure with wire nut.
WIRE NUT
3 gREEN WIRES
CANOPY HATCH INSTALLATION
Step 10. Tuck the wires into the
TILT THE fAN TO
INSTALL LAST
CANOpy SCREW
canopy with the wire nuts pointed
upwards, so that the WHITE, GREEN
and BLACK wires are on opposite
sides of the canopy and all wires are
clear of the canopy opening.
CANOpy
HATCH
Step 11. Install canopy hatch with the
last canopy screw and lock washer. To
do this, tilt the fan body away from
the hatch opening.Tighten the screws
firmly by hand only.
LOCK
WASHER
Step 12. Straighten the fan, then
check to ensure that there is no move-
ment between the canopy and ceiling
or Hang-Tru ball and downrod.
CANOpy
SCREW
6
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Mo d e n a II
INSTALLATION HALOGEN BULB AND GLASS
Step 13. Screw the 100 Watt Halogen bulb into the
socket. If it is touched, or dirty, clean carefully with
a tissue. A dirty glass bulb will cause the bulb to fail
almost immediately.
CAUTION! Do not touch the bulb with your
fingers–it is extremely important that the glass
be clean.
Step 14. Position the indentations in the outer rim of
the glass shade so that they line up with the tabs on the
inside surface of the fan light fixture rim.
Step 15. Carefully lift the glass shade up inside the
lightfixture as far as it will go.
Step 16. Rotate the shade in a clockwise direction
until it is held tightly in place by the three tabs.
CAUTION! Improper installation of glass may
cause it to be damaged or it to fall and break.
NOTE: In compliance with US Federal Energy
Regulations, this ceiling fan contains a device
that restricts the light fixture to a maximum of
190 watts. Exceeding that limit or the marked
limit on this product may result in a fire hazard
or improper operation.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
VERSA•TOUCH2® COnTROl InSTAllATIOn
Versa•Touch2™ hardware (not to scale)
Wood
Screw
1" (2)
Screw
6-32 X 3/8" 6-32 X 1"
(2) (2)
Screw
Drywall
Anchor
6-32 (2)
12v Battery
W-72
W-72
Control Holder
Control
COnTROl BRACkET InSTAllATIOn
SAFETY FIRST: To reduce the risk of electrical shock, this fan must be installed with an isolating wall control/
switch. CAUTION! Do not use with wall dimmer.
warNING: To reduce the risk of fire or electric shock, do not use this fan with any solid state speed control
device. Use only the control provided with this fan.
Step 17. Follow instructions for the type of transmitter control bracket you will be using.
STANDARD
TOggLE
SWITCH
ROCKER
LIgHT
SWITCH
INNER
mOUNTINg
HOLES
OUTER
mOUNTINg
HOLES
SWITCH
COVER
pLATE
SWITCH
COVER
pLATE
CONTROL
bRACKET
CONTROL
bRACKET
Rocker Light Switch
Standard Light Switch
Step A. Break off the two tabs by pushing outward.
Step A. Remove the two screws holding the switch
cover plate. Do not remove the cover plate.
Step B. Remove the two screws holding the switch
cover plate. Do not remove the cover plate.
Step B. Orient the control bracket as shown and line
up the two inner mounting holes with those on the
switch.
Step C. Orient the control bracket as shown and line
up the two inner mounting holes with those on the
switch.
Step C. Insert and tighten the screws using the
provided screwdriver.
Step D. Insert and tighten the screws using the
provided screwdriver.
NOTE: The wall anchors and 6-32 x 1" screws may
be used in situations where mounting to a stud is
not possible. Use the inner mounting holes. After
securing the anchor, discard the anchor’s pointed
screws and use the 6-32 decor ovalhead screws
supplied.
Wall Installation
Step A. Locate a 2x4
wall stud in a convenient
location.
Step B. Orient the control
bracket as shown over
the 2x4 stud.
ANCHOR
pANHEAD
SCREW
StepC.Insertthe1"wood
screws in either the inner
or outer mounting holes
and tighten using the
provided screwdriver.
DRyWALL ANCHOR
WOOD
SCREW 1"
DECOR OVALHEAD SCREW
6-32 x 1"
8
Download from Www.Somanuals.com. All Manuals Search And Download.
®
REmOTE OpERATIOn
Fan Control
To start the fan. Press the selected speed button to run the fan at the desired
speed.
Send Signal
LED
LIgHT
LOW=Low speed MED=Medium speed HIGH=High speed
To turn off the fan, press the FAN OFF button.
mED
airflow direction
To reverse the airflow, press the reVerse button. reVerse operates at any speed
whether the fan is on or off. The fan returns to its set speed after reversing.
HIgH
LOW
Light Control
Turn the light on or off independently from the fan by pressing the LIGHT button.
If you press the button for more than 0.7 seconds, it becomes a dimmer. The light
varies from “bright" to “dim” over approximately 8 seconds. If you continue to hold
the LIGHT button, this sequence will reverse when the light reaches its brightest or
dimmest level. Release the button when the desired level is reached.
fAN
Off
REVERSE
Memory Feature
The last light fuction and fan speed will resume when power is turned back on.
Auto Resume
Quick (pressing less than 0.7 seconds) on/off operation of the LIGHT button maintains
the desired brightness level set previously.
CHAngIngTRAnSmITTER FREqUEnCy SETTIng
Note: All fans leave the factory set to “00000.”
Versa•Touch 2
CONTROL
You will only have to change the dip switch settings in the
remote if you are using more than one fan in the same area
and want to control them separately.
(bACK)
Step 1. At the circuit breaker or fuse box, turn the power off
for the fan you want to change.
step 2. open the battery door of the Versa•Touch control and
remove the batteries.
Step 3. Change the dip switch settings, assuring that they are
different from the previously installed Versa•Touch fan.
Step 4. Re-install the batteries and the battery door on the control.
DIp SWITCH
SET TO
“10000”
DIp SWITCH
SET TO
“01001”
Step 5. At the circuit breaker or fuse box, turn the power back
on for the fan whose frequency you are changing.
Step 6. Within 20 seconds of restoring power, push the HIGH,
MED, and LOW buttons (in that order).
warning!
Do not turn the power off at the circuit breaker,then
back on, for the previously installed Versa•Touch2
fan(s), as you may inadvertently change the
frequency settings for it as well.
Note: You may want to label your controls to assure
you do not mix them up.
If the fan is not functioning after installation:
2
Step 1. Check to make sure that batteries are installed cor-
rectly in the control.
3
1
Step 2. Turn the power off to the fan (from the circuit breaker)
for at least 5 seconds.
Step 3. Turn the power back on (at the circuit breaker) and
push the HIGH, MED, and LOW buttons–in that order–within
20 seconds.
pRESS IN THIS ORDER TO SET
NEW fREqUENCy:
CIRCUIT
bREAKER
OR fUSE bOx
1. HIgH 2. mED
3. LOW
Step 4. The fan should now function properly.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBlESHOOTIngTIpS
Please refer to this troubleshooting guide before requesting service or contacting your dealer for assistance.
pROBlEm
pOSSIBlE REmEDIES
Fan will not start
• Check the main circuit fuses, circuit breakers, and wall switch position. Check all wire
connections. Make sure the power is turned off during this inspection.
• e 9-pin connector is not making good contact.Check the 9-pin connector in the receiver
mounted in the switch housing
• e battery is weak. Install a fresh battery.
• e fan receiver is defective. Replace fan receiver.
• Check the frequency setting: Turn the power off at the circuit breaker, only for the fan
that is not functioning. Check that the jumper switches match in both the receiver and
the transmitter.
Fan wobbles or shakes excessively
Fan is noisy during operation
• Be sure the canopy pin is set properly into the slot on the ball.
• Check that the bladeholders have not been bent during installation and the blades are
balanced.
• e hanger bracket and/or ceiling outlet are attached too loosely. Make sure the hanger
bracket is attached tightly to the ceiling outlet box and the downrod assembly is secured
firmly.
• e downrod is attached to downrod base too loosely.Make sure all the screws are securely
tightened.
• Check and tighten the light fixture retaining screws, glass shade screws, and/or
lightbulb(s).
• Tighten the canopy screws and mounting plate assembly. Make sure the wire nuts inside
the canopy and switch housing are not touching the metal parts and that they have not
fallen off the wire splices.Tighten as necessary.
• Tighten the blade holders to the flywheel (or direct drive motor) and the blades to the
bladeholder screws.
• Make sure all screws in the motor housing are snug but not overly tight.
• If fan is new, it may need to be “broken in.” Run at high speed for several days.
• Replace with alkaline batteries.
Fan does not run on low speed
Battery life is short
Light works, but fan does not work
Fan and light run only on full speed
Fan is missing one speed
Fan does not change speed, but light works
Reverse does not work
• e fan wires are not connected properly.
• e fan receiver is defective. Replace fan receiver.
• e fan receiver is defective. Replace fan receiver.
• e fan receiver is defective. Replace fan receiver.
• e fan receiver is defective. Replace fan receiver.
• ere is frequency interference. Change frequency.
• Check that antenna wire is not touching metal plate.
• e fan receiver is defective. Replace fan receiver.
Fan starts working by itself
Fan operates only when transmitter is close
Fan works, but light does not dim
Fan works, but light does not work
• e fan receiver is defective. Replace fan receiver.
• e light socket is broken. Replace socket.
• A lightbulb is defective. Replace lightbulb.
NOTE: in compliance with US Federal Energy regulations,
this ceiling fan contains a device that restricts the light fixture
to a maximum of 190 watts.Exceeding that limit or the marked
limit on this product may result in a fire hazard or improper
operation.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Mo d e n a II
pRODUCT SpECIFICATIOnS
™
Model Name:
Modena® II
C10GXXM
Motor:
188mm x 20mm Direct Drive
Model Number:
Blade Span:
Blade Iron Pitch:
No. of Blades:
Technology:
Lightbulb:
47"
Dynamic
5
Dimensions:
A =11.8"
B =16.75"
C =2.8"
®
Versa•Touch2 W-72
(1) 100-watt halogen
NOTE: Dimension B
includes light fixture
and glass.
D =8.17"
E =7.0"
Airflow:
5,832 cfm
72 watts
Electricity Use*:
Airflow Efficiency*:
Weight:
28 lbs.
81 cfm/watt
* Performance data is for fan only. no lighting wattage is included.
For questions or to locate the nearest Casablanca Authorized Service Center call toll free: 1-888-227-2178
1.This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions: (1) this device may not cause
harmful interference,and (2) this device must accept any interference received,including interference that may cause undesired operation.
2.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates,uses and can radiate radio frequency energy and,if not installed and used in accordance with the instructions,may cause harmful
interference to radio communications. However,there is no guarantee that interference will not occur in a particular installation. If this equip-
ment does cause harmful interference to radio or television reception,which can be determined by turning the equipment off and on,the
user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna,
Increase the separation between the equipment and receiver, Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected, consult the dealer or an experienced radio/TV technician for help. Note: any changes or modifications to the
transmitter or receiver not expressly approved by Casablanca Fan Company may void one’s authority to operate this remote control.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
|