Carrier Home Security System TSTATCCSEN01 User Manual

TSTATCCSEN01  
Outdoor Temperature Sensor  
Installation Instructions  
NOTE: Read the entire instruction manual before starting the  
installation.  
PERFORMING THE INSTALLATION  
Once the mounting location has been selected, route the intercon-  
necting wiring through the building between thermostat and  
outdoor sensor. The exit point from inside to outside will be the  
location of the outdoor sensor. The location of the wire nuts will  
be either inside or outside of wall depending on whether or not a  
box is used. Allow sufficient wire length for some excess on each  
end.  
SAFETY CONSIDERATIONS  
Read and follow manufacturer instructions carefully. Follow all  
local electrical codes during installation. All wiring must conform  
to local and national electrical codes. Improper wiring or installa-  
tion may damage thermostat sensor.  
Recognize safety information. This is the safety-alert symbol  
When you see this symbol on the equipment and in the instruction  
manual, be alert to the potential for personal injury.  
.
IF AN OUTLET BOX IS USED: (See Fig. 1.)  
Drill a suitable hole in the building wall at selected sensor location.  
Route interconnecting wire through building wall. Remove rear  
knockout from electric box, route wire through box, and attach box  
to wall with supplied wood screws.  
Understand the signal words DANGER, WARNING, and CAU-  
TION. These words are used with the safety-alert symbol. DAN-  
GER identifies the most serious hazards which will result in severe  
personal injury or death. WARNING signifies a hazard which  
could result in personal injury or death. CAUTION is used to  
identify unsafe practices which would result in minor personal  
injury or product and property damage.  
Cut and strip wires to a reasonable length and connect with  
supplied wire nuts. Polarity is unimportant. Seal wires where they  
exit building with a suitable exterior caulk. Fasten cover to box  
with supplied sheet metal screws.  
INTRODUCTION  
FIELD-SUPPLIED  
OUTLET BOX  
The remote temperature sensor is an accessory for all Carrier  
thermostats, except the non-programmable A/C versions. It allows  
the temperature at a remote location to be displayed on the  
thermostat.  
SENSOR  
EXTERIOR  
WALL  
MOUNTING CONSIDERATIONS  
Choose a location for the outdoor sensor after considering the  
following:  
1) A wiring route must be planned between thermostat and  
location of outdoor sensor, prior to installation.  
2) A sensor located in direct sunlight will not read properly while  
the sun is shining on it.  
3) A high location under an eave is ideal because it is protected  
from sun, weather, and people.  
4) The sensor can be mounted directly to a wall using provided  
screws and standoffs or can be used as a cover for a standard  
electric outlet box (not supplied).  
WIRING SELECTION:  
METAL  
SCREWS  
A pair of conductors must be selected to run between mounted  
sensor and thermostat. Conductors must be rated NEC Class 1.  
Thermostat and common bell wire have this rating.  
MOUNTING TO OUTLET BOX:  
A standard electrical box (not included) may be used with the  
sensor plate as its cover. This provides room inside box for wire  
nut connection between sensor wires and wiring run to the  
thermostat.  
A94409  
Fig. 1—Mounting to Outlet Box  
USING SENSOR PLATE:  
Attaching the plate directly to the outside wall simplifies mounting  
and requires less space, but the wire nut transitions to the  
thermostat wiring now need to be made within the wall. This may  
be difficult in some installations.  
Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.  
Book  
Tab misc. misc.  
1
4
PC 101  
Catalog No. 92-33TS-TA13C  
Printed in U.S.A.  
Form TSTAT-3SI  
Pg 1  
12/15/94  
Replaces: New  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Black Decker Rice Cooker RC3203 User Manual
Blanco Indoor Furnishings 157 052 User Manual
Bosch Appliances Welding Consumables KTS 340 User Manual
Bose Headphones MIE2 User Manual
Bradford White Corp Water Heater IGI 180 User Manual
Briggs Stratton Automobile Parts 23C B User Manual
Broan Ventilation Hood 350 User Manual
Campbell Hausfeld Drill DG190600CK S User Manual
Casio Clock 5163 User Manual
Changhong Electric Flat Panel Television LT2618, LT3218, LT3718, LT4018 User Manual