Continuous Ink Supply System
for
CANON PIXMA IP4200
Installation Instruction
For ST Prefilled Version
With Original Chips
Thi s Ver si on of t he Cont i nuous I nk Fl ow Syst em comes wi t h Pr ef i l l ed
Car t r i dges and Aut o Reset Chi ps. You j ust need t o f i l l t he
Reser voi r bot t l es and pr i nt ! The whol e oper at i on i s ver y easy. I t ’
s r eal l y an ef f ect i ve t ool t o save your money.
3、Installation Procedures:
1) First step
Put the CIS at the right side of printer
Take off the rubbers from ink tank’s
Put the Air-filter into the Air-hole
And make sure the tube line does not
twist.
Air-hole.
2) Install chips
、
Carefully remove the original chips
Pay attention when you remove original Finished.
from original cartridges as the picture chips. Make sure that the chips are not
shows.
damaged.
Put some glue on the chip position of
CISS cartridge.
Then stick original chips according to
color of cartridges. Please make sure
that the chips number matches
cartridge number.
Do the same for the other cartridges.
3) Install cartridges
Attache the support arm on the proper Then put the CISS cartridges into printer Please make sure that every cartridge is
position as the picture shown above. well installed according to the color label.
4) Install the tubing.
Clip the tube into the support arm as the pictures shown.
5) Adjust tubing
Adjust the tube length and move from
Left to right for several times.
Please make sure there will be no block Ensure the length of tube so that
and collision when the cartridges move the cartridge can thoroughly move to
from one side to the other. Both sides.
Too long is not OK.
Twist is not OK.
Perfect.
6) Checking the printing head
Enter the Printer Services panel and print a Demo Page.
If it shows any breaks (maybe it caused by air bubbles in the printing head), please clean your printing head. If it still
shows little breaks, especially only for one color, it is unnecessary to repeatedly clean printer-head. Just keep the
printer unusing for about one hour and print a Demo Page again. If it is still abnormal, please kindly contact local
dealer.
7）When cartridges are not recognized, pls operate as the arrowhead shows, In which way, it will not damage the
printer then.
4、Refill Ink
Please pay attention to the ink level in the reservoirs; if the ink level is below 1CM as the above picture shown,
please use refill kits to fill ink into Reservoir bottles. Carefully pull out the rubber plugs from the refill holes.(there is
possibility of ink spattering. Be careful!) Refill ink according to the color in short supply. Then put the rubber back.
(Please keep the printer and the reservoir at the same horizontal line during the process of refilling ink.)
5. Attention for Maintenance:
Take out the CISS including the inner cartridges and other components. Then remove support arm from printer, and
re-install original cartridges. Please inquire local dealer before sending to maintenance.
6. Notice:
1. Please don’t take out cartridge at random after installing the CIS system. Keep the reservoir bottles on the same
level with the printer.
2. Try to keep at least 1/2 inch of ink in the bottles.
3. Don’t place the Reservoir Bottles too much higher or lower than the printer.
4. Suggested using in a dry place between 15 and 35 degree. Avoid exposure to direct sunlight.
5. Don’t reverse or lean the continuous ink supply systems during shipping. Please make sure all the ink filling holes
and ventilation holes are closed tightly during transportation. Otherwise, the ink may leak.
6. Don’t sway the cartridge frequently. It may cause ink leakage.
7. Don’t pull out the connector of cartridge and don’t tear off adhesive tape at the bottom of cartridge.
7. Warning:
1. Not drinkable; keep it out reach of children.
2. Avoid exposure to direct sunshine and don’t keep it in high or freezing temperature.
3. Avoid collision and fallen down.
|