ROUND PARK BENCH
Pig Design
92647
ASSEMBLY INSTRUCTIONS
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Copyright © 2005 by Harbor FreightTools®. All rights reserved. No portion of this manual
or any artwork contained herein may be reproduced in any shape or form without the
express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353
Manual Revised 04/05
Download from Www.Somanuals.com. All Manuals Search And Download.
12. THIS PRODUCT IS MANUFACTURED OF CAST IRON. Do not force any part of the assembly
and do not overtighten the bolts. Serious damage can occur. Do not stand on this Bench. Use
only for intended purpose.The Park Bench is made for children. Children need to be supervised.
Injury could occur if Park Bench is overloaded. Use caution!
13. STORE IDLE EQUIPMENT. When not in use, products must be stored in a dry location to inhibit
damage from moisture and salt air.
14. TIPPING HAZARD. Do not jump or climb on the Bench. Do not allow anyone to sit on the back
of the Bench.
15. REPLACEMENT PARTS AND ACCESSORIES. When servicing, use only identical replacement
parts. Use of any other parts will void the warranty.
Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot
cover all possible conditions and situations that may occur. It must be understood by the operator
that common sense and caution are factors which cannot be built into this product, but must be
supplied by the operator.
UNPACKING
When unpacking, check to make sure all parts shown on the Parts List (page 5) are
included. If any parts are missing or broken, please call Harbor Freight Tools at the
number shown on the cover of this manual as soon as possible.
ASSEMBLY INSTRUCTIONS
We suggest you assemble the unit on a soft surface to avoid damage to the finish.
ASSEMBLY OF BENCH
1.
PLACING SLATS: Attach the five Seat Slats (3) in the channel of the End Pieces (2)
as shown. Note: The Round Slat is to be anchored in the front of the Bench. Use the
Bolts, Washers, and Nuts (4) to attach. See Figure 1.
Note: It may become necessary to enlarge the holes in the End Pieces (2). Clear
the hole of paint by sliding a bolt through the hole or using a drill before assembly.
Round Back
Assembly (1)
End Piece-Right
Side (2-R)
Bolts (4)
Seat Slats (3)
Round Slat
in Front
Figure 1
Page 3
SKU 92647
For technical questions, please call 1-800-444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
2.
Attach the Round Back Assembly (1) to the End Pieces left and right (2). Use Bolts (5) to
attach. Hand tighten only. See Figure 2.
Round
Back Assembly (1)
End Piece (2)
Bolt (5)
Bolt (5)
Bolt (8)
Bolt (8)
Figure 2
3.
With the assistance of another person, carefully turn the Bench upside down and attach the
Support Bracket (6) with the Self Tap Screws (7) in the two center predrilled holes. Screw
into the second wood slat counting from the back of the seat. Use Bolts, Nuts and
Washers (5) to secure the ends of the Support Bracket to the End Pieces (2), left and right.
See Figure 3.
Bolt, Nut, &
Washer (5)
Support Bracket (6)
Self Tap
Screw (7)
(underneath)
Bolt, Nut, &
Washer (5)
Figure 3
Note: Use a small Carpenter’s Square to adjust the angle between the End Pieces (2L & R)
and Slats so you can maintain the 90° angle.
Page 4
SKU 92647
For technical questions, please call 1-800-444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
4.
Tighten all hardware at this time (maintain the 90° angle while tightening all hardware).
Check periodically to be sure all hardware stays tightened.
PARTS LIST
PART #
DESCRIPTION
QTY
1
2
3
4
5
6
7
8
1
2
Round Back Assembly
End Pieces Left & Right
5
Seat Slats
10
4
Bolt 6 x 30mm, Nuts 6mm, & Washers 6mm
Bolt 6 x 20mm, & Washers 6mm
Support Bracket
1
2
Self Tap Screw 4 x 10mm
Bolt 8 x 30mm, Nuts 8mm, & Washers 8mm
4
ASSEMBLY ILLUSTRATION
Part 1
Part 2-L
Part 7
Part 2-R
Parts 5
(not shown)
Part 6
(not shown)
Part 2
(rounded
slat)
Part 8
Seat Slates (3)
MAINTENANCE
For better and safer performance, keep all parts of this product clean and dry at
all times.
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS
MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO
REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR
EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN
BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES
ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR
REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF
REPLACEMENT PARTS THERETO.
Page 5
SKU 92647
For technical questions, please call 1-800-444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
|