Bush Hog Saw 00786976C User Manual

160 Series

REAR MOUNTED BLADE

Published 08/10

Part No. 00786976C

OPERATOR’S MANUAL

This Operator's Manual is an integral part of the safe operation of this machine and must

be maintained with the unit at all times. READ, UNDERSTAND, and FOLLOW the Safety

and Operation Instructions contained in this manual before operating the equipment. C01-

Cover

BUSH HOG^®

2501 Griffin Ave.

Selma, AL 36703

334-874-2700

www.bushhog.com

$0.00

Download from Www.Somanuals.com. All Manuals Search And Download.

TABLE OF CONTENTS

SAFETY SECTION ........................................................................................................... 1-1

Safety Messages ............................................................................................................................................1-2

Decal Location .................................................................................................................................................1-9

Decal Descriptio n ...........................................................................................................................................1-11

Federal Laws and Regulations .....................................................................................................................1-15

INTRODUCTION SECTION .............................................................................................. 2-1

ASSEMBLY SECTION ..................................................................................................... 3-1

Assembly of Moldboard to Mainframe ............................................................................................................3-2

Gauge Wheel (Extra Equipment) .....................................................................................................................3-4

Skid Shoes & Quick Tach End Plates (Extra Equipment) ...............................................................................3-4

Hydraulic System ............................................................................................................................................3-4

Hydraulic Control Valve (Extra Equipment)......................................................................................................3-5

Selector Valve (Extra Equipment) ...................................................................................................................3-5

Wrist Pin & Bushing Arrangement ...................................................................................................................3-6

OPERATION SECTION .................................................................................................... 4-1

Standard Equipment and Specifications ..........................................................................................................4-3

OPERATOR REQUIREMENTS ......................................................................................................................4-4

TRACTOR REQUIREMENTS..........................................................................................................................4-5

ROPS and Seat Belt .......................................................................................................................................4-5

Tractor Horsepower ........................................................................................................................................4-5

Tractor 3-Point Hitch .......................................................................................................................................4-6

Front End Weight ............................................................................................................................................4-6

GETTING ON AND OFF THE TRACTOR ......................................................................................................4-6

Boarding the Tractor .......................................................................................................................................4-7

Dismounting the Tractor ..................................................................................................................................4-7

STARTING THE TRACTOR ...........................................................................................................................4-8

CONNECTING THE REAR BLADE TO THE TRACTOR ...............................................................................4-8

Connecting the Rear Blade .............................................................................................................................4-9

PRE-OPERATION INSPECTION AND SERVICE ........................................................................................4-10

Tractor Pre-Operation Inspection/Service .....................................................................................................4-10

Blade Pre-Operation Inspection/Service .......................................................................................................4-11

DRIVING THE TRACTOR AND IMPLEMENT ..............................................................................................4-14

Starting the Tractor .......................................................................................................................................4-15

Brake and Differential Lock Setting ...............................................................................................................4-15

Driving the Tractor and Blade .......................................................................................................................4-16

OPERATING THE TRACTOR AND IMPLEMENT ........................................................................................4-16

Operating the Blade ......................................................................................................................................4-17

Shutting Down the Implement .......................................................................................................................4-18

DISCONNECTING THE BLADE FROM THE TRACTOR .............................................................................4-18

BLADE STORAGE ........................................................................................................................................4-19

TRANSPORTING THE TRACTOR AND IMPLEMENT ................................................................................4-19

Transporting on Public Roadways ................................................................................................................4-20

Hauling the Tractor and Implement ...............................................................................................................4-22

Troubleshooting Guide...................................................................................................................................4-24

MAINTENANCE SECTION ............................................................................................... 5-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Lubrication ......................................................................................................................................................5-2

Proper Torque For Fasteners ..........................................................................................................................5-3

Download from Www.Somanuals.com. All Manuals Search And Download.

SAFETY SECTION

Safety Section 1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

SAFETY

Safety Messages

A careful operator is the best operator. Safety is of primary importance to the manufacturer and should be to

the owner/operator. Most accidents can be avoided by being aware of your equipment, your surroundings, and

observing certain precautions. The first section of this manual includes a list of Safety Messages that, if

followed, will help protect the operator and bystanders from injury or death. Read and understand these Safety

Messages before assembling, operating or servicing this Implement. This equipment should only be operated

by those persons who have read the manual, who are responsible and trained, and who know how to do so

responsibly.

The Safety Alert Symbol combined with a Signal Word, as seen below, is used throughout this

manual and on decals which are attached to the equipment. The Safety Alert Symbol means:

“ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!” The Symbol and Signal Word

are intended to warn the owner/operator of impending hazards and the degree of possible injury

faced when operating this equipment.

Practice all usual and customary safe working precautions and above all---remember safety is

up to YOU. Only YOU can prevent serious injury or death from unsafe practices.

Indicates an imminently hazardous situation that, if not avoided, WILL result in DEATH OR

VERY SERIOUS INJURY.

Indicates an imminently hazardous situation that, if not avoided, COULD result in DEATH

OR SERIOUS INJURY.

Indicates an imminently hazardous situation that, if not avoided, MAY result in MINOR

INJURY.

Identifies special instructions or procedures that, if not strictly observed, could result in

damage to, or destruction of the machine, attachments or the environment.

NOTE: Identifies points of particular interest for more efficient and convenient operation or repair.^(SG-1)

READ, UNDERSTAND, and FOLLOW the following Safety Messages. Serious injury or

death may occur unless care is taken to follow the warnings and instructions stated in the

Safety Messages. Always use good common sense to avoid hazards. ^(SG-2)

Si no lee ingles, pida ayuda a alguien que si lo lea para que le traduzca las

medidas de seguridad. ^(SG-3)

160 Series 08/10

Safety Section 1-2

Download from Www.Somanuals.com. All Manuals Search And Download.

SAFETY

Never operate the Tractor or Implement until you have read and

completely understand this Manual, the Tractor Operator’s Manual, and

each of the Safety Messages found in the Manual or on the Tractor and

Implement. Learn how to stop the tractor engine suddenly in an

emergency.

Never allow inexperienced or untrained personnel to

operate the Tractor or Implement without supervision. Make sure the

operator has fully read and understood the manuals prior to operation.

(SG-4)

Always maintain the safety signs in good readable condition. If the safety signs are missing,

damaged, or unreadable, obtain and install replacement safety signs immediately. ^(SG-5)

Make certain that the “Slow Moving Vehicle” (SMV) sign is installed in

such a way as to be clearly visible and legible. When transporting the

Equipment use the Tractor flashing warning lights and follow all local

traffic regulations. ^(SG-6)

Operate this Equipment only with a Tractor equipped with an approved roll-

over-protective system (ROPS). Always wear seat belts. Serious injury or

even death could result from falling off the tractor--particularly during a turnover

when the operator could be pinned under the ROPS. ^(SG-7)

Do not modify or alter this Implement. Do not permit anyone to modify or alter this

Implement, any of its components or any Implement function. ^(SG-8)

BEFORE leaving the tractor seat, always set the parking brake and/or set

the tractor transmission in parking gear, disengage the PTO, stop the

engine, remove the key, and wait for all moving parts to stop. Place the

tractor shift lever into a low range or parking gear to prevent the tractor

from rolling. Never dismount a Tractor that is moving or while the engine

is running. Operate the Tractor controls from the tractor seat only. ^(SG-9)

Never allow children or other persons to ride on the Tractor or Implement.

Falling off can result in serious injury or death. ^(SG-10)

160 Series 08/10

Safety Section 1-3

Download from Www.Somanuals.com. All Manuals Search And Download.

SAFETY

Never allow children to operate, ride on, or come close to the Tractor or

Implement. Usually, 16-17 year-old children who are mature and

responsible can operate the implement with adult supervision, if they

have read and understand the Operator’s Manuals, been trained in

proper operation of the tractor and Implement, and are physically large

enough to reach and operate the controls easily. ^(SG-11)

Do not mount or dismount the Tractor while the tractor is moving. Mount

the Tractor only when the Tractor and all moving parts are completely

stopped. ^(SG-12)

Start tractor only when properly seated in the Tractor seat. Starting a

tractor in gear can result in injury or death. Read the Tractor operators

manual for proper starting instructions. ^(SG-13)

Never work under the Implement, the framework, or any lifted

component unless the Implement is securely supported or blocked up

to prevent sudden or inadvertent falling which could cause serious

injury or even death. ^(SG-14)

Do not operate this Equipment with hydraulic oil or fuel leaking. Oil

and fuel are explosive and their presence could present a hazard. Do

not check for leaks with your hand! High-pressure oil streams from

breaks in the line could penetrate the skin and cause tissue damage

including gangrene. To check for a hose leak, SHUT the unit ENGINE

OFF and remove all hydraulic pressure. Wear oil impenetrable gloves,

safety glasses and use Cardboard to check for evidence of oil leaks. If

you suspect a leak, REMOVE the HOSE and have it tested at a Dealer.

If oil does penetrate the skin, have the injury treated immediately by a

physician knowledgeable and skilled in this procedure. (SG-15)

The operator and all support personnel should wear hard hats, safety

shoes, safety glasses, and proper hearing protection at all times for

protection from injury including injury from items that may be thrown by

the equipment. ^(SG-16)

160 Series 08/10

Safety Section 1-4

Download from Www.Somanuals.com. All Manuals Search And Download.

SAFETY

PROLONGED EXPOSURE TO LOUD NOISE MAY CAUSE

PERMANENT HEARING LOSS! Tractors with or without an Implement

attached can often be noisy enough to cause permanent hearing loss.

We recommend that you always wear hearing protection if the noise in

the Operator’s position exceeds 80db. Noise over 85db over an

extended period of time will cause severe hearing loss. Noise over 90db

adjacent to the Operator over an extended period of time will cause

permanent or total hearing loss. NOTE: Hearing loss from loud noise

[from tractors, chain saws, radios, and other such sources close to the

ear] is cumulative over a lifetime without hope of natural recovery. ^(SG-I7)

Transport only at speeds where you can maintain control of the

equipment. Serious accidents and injuries can result from operating this

equipment at high speeds. Understand the Tractor and Implement and

how it handles before transporting on streets and highways. Make sure the Tractor steering

and brakes are in good condition and operate properly.

Before transporting the Tractor and Implement, determine the proper transport speeds for

you and the equipment. Make sure you abide by the following rules:

Test the tractor at a slow speed and increase the speed slowly. Apply the Brakes smoothly

to determine the stopping characteristics of the Tractor and Implement. As you increase

the speed of the Tractor the stopping distance increases.

Determine the maximum

transport speed not to exceed 20 mph (30 kph) for transporting this equipment.

Test the equipment at a slow speed in turns. Increase the speed through the turn only after

you determine that the equipment can be operated at a higher speed. Use extreme care

and reduce your speed when turning sharply to prevent the tractor and implement from

turning over. Determine the maximum turning speed for you and this equipment before

operating on roads or uneven ground.

Only transport the Tractor and Implement at the speeds which allow you to properly control

the equipment.

Be aware of the operating conditions. Do not operate the Tractor with weak or faulty brakes

or worn tires. When operating down a hill or on wet or rain slick roads, the braking distance

increases: use extreme care and reduce your speed. When operating in traffic always use

the Tractor’s flashing warning lights and reduce your speed. Be aware of traffic around you

and watch out for the other guy. (SG-19)

Never attempt to lubricate, adjust, or remove material from the Implement while it is in

motion or while tractor engine is running. ^(SG-20)

160 Series 08/10

Safety Section 1-5

Download from Www.Somanuals.com. All Manuals Search And Download.

SAFETY

Periodically inspect all moving parts for wear and replace when

necessary with authorized service parts. Look for loose fasteners, worn

or broken parts, and leaky or loose fittings. Make sure all pins have

cotter pins and washers. Serious injury may occur from not maintaining

this machine in good working order. ^(SG-21)

Always read carefully and comply fully with the manufacturer’s

instructions when handling oil, solvents, cleansers, and any other

chemical agent. ^(SG-22)

Never run the Tractor engine in a closed building or without adequate ventilation. The

exhaust fumes can be hazardous to your health. ^(SG-23)

KEEP AWAY FROM ROTATING ELEMENTS to prevent entanglement

and possible serious injury or death. ^(SG-24)

Never allow children to play on or around Tractor or Implement. Children can slip or fall off

the Equipment and be injured or killed. Children can cause the Implement to shift or fall

crushing themselves or others. ^(SG-25)

NEVER use drugs or alcohol immediately before or while operating the

Tractor and Implement. Drugs and alcohol will affect an operator’s

alertness and coordination and therefore affect the operator’s ability to

operate the equipment safely. Before operating the Tractor or Implement,

an operator on prescription or over-the-counter medication must consult

a medical professional regarding any side effects of the medication that

would hinder their ability to operate the Equipment safely. NEVER

knowingly allow anyone to operate this equipment when their alertness or

coordination is impaired. Serious injury or death to the operator or others

could result if the operator is under the influence of drugs or alcohol. ^(SG-27)

160 Series 08/10

Safety Section 1-6

Download from Www.Somanuals.com. All Manuals Search And Download.

SAFETY

Operate the Tractor and/or Implement controls only while properly seated in the Tractor seat

with the seat belt securely fastened around you. Inadvertent movement of the Tractor or

Implement may cause serious injury or death. ^(SG-29)

Be particularly careful when transporting the Implement with the Tractor. Turn curves or go

up hills only at a low speed and using a gradual steering angle. Rear mounted implements

move the center of gravity to the rear and remove weight from the front wheels. Make

certain, by adding front ballast, that at least 20% of the tractor’s weight is on the front wheels

to prevent rearing up, loss of steering control or Tractor tip-over. Slow down on rough or

uneven surfaces to prevent loss of steering control which could result in property damage

or possible injury. Do not transport unless 3-Point lift lever is fully raised and in the latched

transport position. Dropping implement in transport can cause serious damage to the

tractor and/or Implement and possibly cause the operator or others to be injured or killed.

(S3PT-02)

Relieve hydraulic pressure prior to doing any maintenance or repair work

on the Implement. Place the Implement on the ground or securely

blocked up, disengage the PTO, and turn off the tractor engine. Push

and pull the Remote Cylinder lever in and out several times prior to

starting any maintenance or repair work. ^(S3PT-09)

This Implement may be wider than the Tractor. Be careful when operating or transporting

this equipment to prevent the Implement from running into or striking sign posts, guard rails,

concrete abutments or other solid objects. Such an impact could cause the Implement and

Tractor to pivot violently resulting in loss of steering control, serious injury, or even death.

Never allow the Implement to contact obstacles. ^(S3PT-12)

There are obvious and hidden potential hazards in operating Rear Blades and Box Scrapers

as in all power-driven equipment. REMEMBER! This machine is often operated in rough

terrain conditions that include gullies, holes, slopes, hidden obstructions and the like.

Serious injury or even death may occur unless care is taken to assure the personal safety of

the operator and bystanders in the area. ^(SBL-1)

Keep fingers clear of adjusting holes. A sudden movement could cause injury or even

amputate fingers. KEEP CHILDREN AWAY WHEN MAKING ADJUSTMENTS. ^(SBL-3)

NEVER PARK BLADE ON THE BACK OF THE MOLDBOARD. Inadvertent falling could

cause serious injury or even death. ALWAYS LOWER HITCH onto stand or onto secure

blocks. ^(SBL-2)

Never leave blade unattended in the lifted position. Accidental operation of lifting lever or a

hydraulic failure may cause sudden drop of unit with subsequent injury or death by crushing.

Lower Stand and pin in place, or put a secure support under the A-Frame. Lower Blade

carefully to the ground. Do not put hands or feet under lifted components. (SBL-4)

160 Series 08/10

Safety Section 1-7

Download from Www.Somanuals.com. All Manuals Search And Download.

SAFETY

Rear Blades can fall down if not properly supported. Always use the stand on the front hitch

or block up securely to prevent falling and possible crushing injury and/or back injury from

lifting heavy components. ^(SBL-5)

PARTS INFORMATION

Bush Hog products are designed utilizing specifically matched system components to ensure optimum

equipment performance. These parts are made and tested to Bush Hog specifications. Non-genuine "will fit"

parts do not consistently meet these specifications. The use of “will fit” parts may reduce equipment

performance, void warranties, and present a safety hazard. Use genuine Bush Hog parts for economy and

safety. ^(SPBH-2)

SEE YOUR BUSH HOG DEALER

In addition to the design and configuration of this Implement, including Safety Signs and Safety Equipment,

hazard control and accident prevention are dependent upon the awareness, concern, prudence, and proper

training of personnel involved in the operation, transport, maintenance, and storage of the machine. Refer

also to Safety Messages and operation instruction in each of the appropriate sections of the Tractor and

Equipment Manuals. Pay close attention to the Safety Signs affixed to the Tractor and Equipment. ^(SG-18)

160 Series 08/10

Safety Section 1-8

Download from Www.Somanuals.com. All Manuals Search And Download.

SAFETY

Decal Location

NOTE: Bush Hog supplies safety decals on this product to promote safe operation. Damage to the decals may

occur while in shipping, use, or reconditioning. Bush Hog cares about the safety of its customers, operators,

and bystanders, and will replace the safety decals on this product in the field, free of charge (Some shipping

and handling charges may apply). Contact your Bush Hog dealer to order replacement decals.

160 Series 08/10

Safety Section 1-9

Download from Www.Somanuals.com. All Manuals Search And Download.

SAFETY

ITEM

PART NO.

QTY

LEVEL

DESCRIPTION

10.

00725746

02965262

00786980

999000

PELIGRO

WARNING

IMPORTANT

WARNING

REFLECT

INSTRUCT

LOGO

Translate Safety Material

Oil Penetration

Genuine Bush Hog Parts

Multi-Hazard for Blades

Multi-Hazard General

SMV Emblem

999200

03200347

000678

Grease Fitting Inside

Notice to Owner

00763977

00786979

00786982

00786989

nfs

Bush Hog

NAME

160-08

NAME

160-10

11.

12.

13.

14.

15.

SER PLT

REFLECT

___________

MANUAL

Serial Plate

1458392

1458393

00776031

00786976C

Red Reflector - 8' & 10'

Amber Reflector - 8' & 10 '

Canister (Operator Manual Inside)

Operator’s Manual

*Provided by Tractor Manufacturer

160 Series 08/10

Safety Section 1-10

Download from Www.Somanuals.com. All Manuals Search And Download.

SAFETY

Decal Description

Peligro Translation, If you do not know how to read

English, please find someone who knows how to

read English.

P/N 00725746

WARNING! Failure to INSPECT and REPAIR or

REPLACE Hoses may allow worn Hoses to rupture

SUDDENLY and VIOLENTLY with resulting serious

BODILY INJURY from SCALDING or FIRE with

resulting BURN INJURY or DEATH.

P/N 02965262

For safety and to guarantee optimum product

reliability always use genuine Bush Hog

replacement parts.

P/N 00786980

WARNING!-Multi-Hazard for blades

P/N 999000

160 Series 08/10

Safety Section 1-11

Download from Www.Somanuals.com. All Manuals Search And Download.

SAFETY

WARNING!- Multiple Hazard and General Safety

P/N 999200

Slow Moving Vehicle Decal. Keep SMV reflector

clean and visible. DO NOT transport or operate

without the SMV.

P/N 03200347

Information that Grease Fitting is present and must

apply grease

P/N 000678

Operator's Manual (with repair parts) and warranty

was attached to this implement during final

inspection.

P/N 00763977

160 Series 08/10

Safety Section 1-12

Download from Www.Somanuals.com. All Manuals Search And Download.

SAFETY

Logo Product Name: Bush Hog

P/N 00786979

LOGO PRODUCT NAME: 160-08

P/N 00786982

LOGO PRODUCT NAME: 160-10

P/N 00786989

Red Reflector. Keep reflectors clean and visible.

P/N 1458392

160 Series 08/10

Safety Section 1-13

Download from Www.Somanuals.com. All Manuals Search And Download.

SAFETY

Amber Reflector. Keep reflectors clean and visible.

P/N 1458393

Read Operator’s Manual! The operator’s manual is

located inside this canister. If the manual is

missing order one from your dealer.

P/N 00776031

160 Series 08/10

Safety Section 1-14

Download from Www.Somanuals.com. All Manuals Search And Download.

SAFETY

Federal Laws and Regulations

This section is intended to explain in broad terms the concept and effect of federal laws and regulations concerning

employer and employee equipment operators. This section is not intended as a legal interpretation of the law and

should not be considered as such.

Employer-Employee Operator Regulations

U.S. Public Law 91-596 (The Williams-Steiger Occupational and Health Act of 1970) OSHA

This Act Seeks:

“...to assure so far as possible every working man and woman in the nation safe and healthful working

conditions and to preserve our human resources...”

DUTIES

Sec. 5 (a) Each employer-

(1) shall furnish to each of his employees employment and a place of employment which are free from

recognized hazards that are causing or are likely to cause death or serious physical harm to his employees;

(2) shall comply with occupational safety and health standards promulgated under this Act.

(b) Each employee shall comply with occupational safety and health standards and all rules, regulations and

orders issued pursuant to this Act which are applicable to his own actions and conduct.

OSHA Training Requirements

Title 29, Code of Federal Regulations Part 1928.57(a)(6). www.osha.gov

Operator instructions. At the time of initial assignment and at least annually thereafter, the employer shall

instruct every employee who operates an agricultural tractor and implements in the safe operating practices

and servicing of equipment with which they are or will be involved, and of any other practices dictated by the

work environment.

Keep all guards in place when the machine is in operation;

Permit no riders on equipment

Stop engine, disconnect the power source, and wait for all machine movement to stop before servicing,

adjusting, cleaning or unclogging the equipment, except where the machine must be running to be properly

serviced or maintained, in which case the employer shall instruct employees as to all steps and procedures

which are necessary to safely service or maintain the equipment.

Make sure everyone is clear of machinery before starting the engine, engaging power, or operating the

machine.

Employer Responsibilities:

To ensure employee safety during Tractor and Implement operation, it is the employer’s responsibility to:

1. Train the employee in the proper and safe operation of the Tractor and Implement.

2. Require that the employee read and fully understand the Tractor and Implement Operator’s manual.

3. Permit only qualified and properly trained employees to operate the Tractor and Implement.

4. Maintain the Tractor and Implement in a safe operational condition and maintain all shields and guards on the

equipment.

5. Ensure the Tractor is equipped with a functional ROPS and seat belt and require that the employee operator

securely fasten the safety belt and operate with the ROPS in the raised position at all times.

6. Forbid the employee operator to carry additional riders on the Tractor or Implement.

7. Provide the required tools to maintain the Tractor and Implement in a good safe working condition and provide the

necessary support devices to secure the equipment safely while performing repairs and service.

8. Require that the employee operator stop operation if bystanders or passersby come within 25 feet.

Child Labor Under 16 Years of Age

Some regulations specify that no one under the age of 16 may operate power machinery. It is your responsibility to

know what these regulations are in your own area or situation. (Refer to U.S. Dept. of Labor, Employment Standard

Administration, Wage & Home Division, Child Labor Bulletin #102.)

160 Series 08/10

Safety Section 1-15

Download from Www.Somanuals.com. All Manuals Search And Download.

INTRODUCTION SECTION

Introduction Section 2-1

Download from Www.Somanuals.com. All Manuals Search And Download.

INTRODUCTION

This 160 Series Blade is designed with care and built with quality materials by skilled workers. Proper

assembly, maintenance, and operating practices, as described in this manual, will help the owner/operator get

years of satisfactory service from the machine.

The purpose of this manual is to familiarize and instruct. The Assembly Section instructs the owner/operator in

the correct assembly of the Blade using standard and optional equipment.

Careful use and timely service saves extensive repairs and costly downtime losses. The Operation and

Maintenance Sections of the manual train the owner/operator how to work the Blade correctly and attend to

appropriate maintenance. The Troubleshooting Guide helps diagnose difficulties and offers solution to the

problems.

Safety is of primary importance to the owner/operator and to the manufacturer. The first section of this manual

includes a list of Safety Messages, that, if followed, will help protect the operator and bystanders from injury or

death. Many of the Safety Messages will be repeated throughout the manual. The owner/operator/dealer

should know these Safety Messages before assembly and be aware of the hazards of operating this blade

during assembly, use, and maintenance. The Safety Alert Symbol combined with a Signal Word, as seen

below, is intended to warn the owner/operator of impending hazards and the degree of possible injury faced

when operating this machine.

Indicates an imminently hazardous situation that, if not avoided, WILL result in DEATH OR

VERY SERIOUS INJURY.

Indicates an imminently hazardous situation that, if not avoided, COULD result in DEATH

OR SERIOUS INJURY.

Indicates an imminently hazardous situation that, if not avoided, MAY result in MINOR

INJURY.

Identifies special instructions or procedures that, if not strictly observed, could result in

damage to, or destruction of the machine, attachments or the environment.

160 Series 08/10

Introduction Section 2-2

Download from Www.Somanuals.com. All Manuals Search And Download.

INTRODUCTION

The 160 Series Blade is available in widths of 8' and 10' and features a heavy-duty CAT II-III three-point hitch

and quick-hitch. The 10' model is rated for up to 160 PTO HP wheel-type tractors. The Blade is available with

either hydraulic or manual mainframe swing, moldboard angle, and moldboard tilt. The Blade can be offset a

maximum of 37" for working outside the dual wheels on larger horsepower tractors. The 4" diameter solid steel

kingpin, boxed section reinforced 1/2” x 18" moldboard, and the superior strength of the mainframe ensure

dependability. The bolt-on gauge wheels are an excellent feature in helping to control the cutting depth. This is

especially critical when trying to leave a smooth finish. Skid shoes, quick-tach end plates, and single or dual

gauge wheels are optional equipment to help make the a more versatile tool.

At least 20% of the tractor’s weight must be on the front tires with the implement lifted to

provide adequate traction for safe steering under good conditions. Slow down on hills,

rough terrain, and curves.

Front and rear, and left and right are determined by the normal direction of travel (the same as on your

automobile).

160 Series 08/10

Introduction Section 2-3

Download from Www.Somanuals.com. All Manuals Search And Download.

INTRODUCTION

Attention Owner/Operator

BEFORE OPERATING THIS MACHINE:

1. Carefully read the Operator’s Manual, completely understand the Safety Messages and instructions, and

know how to operate correctly both the tractor and implement.

2. Fill out the Warranty Card in full. Be sure to answer all questions, including the Serial Number of the

implement. Mail within 30 days of delivery date of this implement.

NOTE: Warranties are honored only if completed “Owner Registration and Warranty” forms are received by

Alamo Group within thirty days of delivery of the implement.

3. Record the Blade Model and Serial Numbers on the Warranty page at the front of the Operator’s Manual.

Keep this as part of the permanent maintenance file for the implement.

160 Series 08/10

Introduction Section 2-4

Download from Www.Somanuals.com. All Manuals Search And Download.

ASSEMBLY SECTION

Assembly Section 3-1

Download from Www.Somanuals.com. All Manuals Search And Download.

ASSEMBLY

Assembly of Moldboard to Mainframe

The Bush Hog 160 Series is shipped in two bundles. The Mainframe, A-Frame and Moldboard Carrier are in

one bundle; the Moldboard is in the second bundle. The assembly of the Moldboard to the Moldboard Carrier is

made by inserting the Moldboard Pivot Pin and securing with Screws.

Until Hydraulic Cylinders are connected and under pressure of Manual Adjusting Links

installed, block Moldboard to Moldboard Carrier to prevent possible tilting and falling from

stand.

160 Series 08/10

Assembly Section 3-2

Download from Www.Somanuals.com. All Manuals Search And Download.

ASSEMBLY

Attach Moldboard Tilt Cylinder with the Rod End

attached to the Moldboard (Figure Asm-0002) or

optional Manual Adjusting links.

Attach the Moldboard Pivot Cylinder as shown in

Figure Asm-0003 or optional Manual Adjusting

Links.

Attach the Mainframe Swing Cylinder as shown in

Figure Asm-0004 or optional Manual Adjusting

Links.

160 Series 08/10

Assembly Section 3-3

Download from Www.Somanuals.com. All Manuals Search And Download.

ASSEMBLY

Gauge Wheel (Extra Equipment)

Mounting Holes have been provided for mounting

the Gauge Wheel to the Mainframe. Dual or Single

Wheels with laminated puncture proof or pneumatic

tires are optional. Assembly of the Hydraulic

Cylinder to the Gauge Wheel Beam must be in the

direction as shown in Figure Asm-0005. It is also

important to route the hydraulic Hose through the

Hose Retainers designed for this equipment.

Skid Shoes & Quick Tach End Plates (Extra Equipment)

Hydraulic System

The Hydraulic Cylinders are designed to be used in conjunction with your tractor's Hydraulic System. The

Cylinders and Hose are designed for maximum system pressure of 2500 PSI.

Keep Cylinders and Hose free from internal contamination. Never leave a disconnected

Hose end open. Use a sealant when attaching hydraulic Hose to Cylinder. Do not over

tighten fittings as this will break out the Cylinder Port Housings. When testing for a leaky

Hose or Connection use a piece of cardboard of wood to detect pinhole leaks - NOT YOUR

HAND. A high-pressure stream of escaping hydraulic fluid can penetrate skin and cause

serious infection or reaction, in addition to physical damage to internal flesh.

160 Series 08/10

Assembly Section 3-4

Download from Www.Somanuals.com. All Manuals Search And Download.

ASSEMBLY

Hydraulic Control Valve (Extra Equipment)

A 3 Spool 4 way Hydraulic Control Valve, open center or closed center, is available as Accessory Equipment.

This allows you to operate 4 Hydraulic Cylinders from two remote outlets. Connect the 3 Spool Valve to one

outlet to operate three Cylinders. Use the other remote outlet to operate the fourth Cylinder.

If Closed Center Valve is used, do not use the adjustable Relief Assembly. Use the No-Relief

Assembly.

Selector Valve (Extra Equipment)

If the Mainframe Swing, Moldboard Pivot and Tilt

are fully hydraulic, as an added feature, all three

Cylinders can be operated from two remote outlets.

Below is a schematic diagram showing proper

routing of two Cylinders through the Selector Valve.

When installing this Valve, observe all safety

precautions as hydraulic lines are under high

pressure (2500 PSI). If additional information is

required concerning your hydraulic system, contact

your Bush Hog dealer.

160 Series 08/10

Assembly Section 3-5

Download from Www.Somanuals.com. All Manuals Search And Download.

ASSEMBLY

Wrist Pin & Bushing Arrangement

160 Series 08/10

Assembly Section 3-6

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATION SECTION

Operation Section 4-1

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATION

BUSH HOG 160 SERIES REAR MOUNTED BLADE

OPERATION INSTRUCTIONS

Your Bush Hog 160 Series should now be assembled and inspected for any evidence of defective or damaged

parts before use. Any evidence of damage should be reported to your dealer immediately. After Hydraulic

Lines have been attached to tractor and 3-Point Hitch attached, carefully remove safety blocks from Moldboard

pivot Point.

This section of the Operator’s Manual is designed to familiarize, instruct, and educate safe and proper blade

use to the operator. Pictures contained in this section are intended to be used as a visual aid to assist in

explaining the operation of a blade. Some pictures may show shields removed for purposes of clarity. NEVER

OPERATE this implement without all shields in place and in good operational condition. The operator must be

familiar with the blade and tractor operation and all associated safety practices before operating the blade and

tractor. Proper operation of the blade, as detailed in this manual, will help ensure years of safe and satisfactory

use of the blade.

READ AND UNDERSTAND THE ENTIRE OPERATING INSTRUCTIONS AND SAFETY SECTION OF THIS

MANUAL AND THE TRACTOR MANUAL BEFORE ATTEMPTING TO USE THE TRACTOR AND

IMPLEMENT. If you do not understand any of the instructions, contact your nearest authorized dealer for a

full explanation. Pay close attention to all safety signs and safety messages contained in this manual and

those affixed to the implement and tractor. OPS-U- 0001

READ, UNDERSTAND, and FOLLOW the following Safety Messages. Serious injury or

death may occur unless care is taken to follow the warnings and instructions stated in the

Safety Messages. Always use good common sense to avoid hazards. ^(SG-2)

Si no lee ingles, pida ayuda a alguien que si lo lea para que le traduzca las

medidas de seguridad. ^(SG-3)

160 Series 08/10

Operation Section 4-2

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATION

1. Standard Equipment and Specifications

Max. 2-Wheel Drive Tractor HP:

(PTO) 8’

(PTO) 10’

190 HP

160 HP

Max. Front Wheel Assist Tractor:

HP (PTO) 8’

162 HP

HP (PTO) 10’

136 HP

Moldboard Width

Moldboard Dimension

Cutting Edge

8’ or 10’

1/2” x 18”

1/2” x 6”

Std.

Support Stand

Hitch

CAT II-III and QH

4”

King Pin Diameter

Adjustment Types

Offset (Maximum Left or Right)

Pivot:

Hydraulic or Manual

37”

Forward Angle

7-45 Degrees

5-15 Degrees

Reverse Angle

Tilt (Up and Down)

No. of No-Wrench Adjustments:

(on manual adjustments model)

Weight (Approx.):

8’

1339 lbs.

1459 lbs.

10’

160 Series 08/10

Operation Section 4-3

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATION

2. OPERATOR REQUIREMENTS

Safe operation of the unit is the responsibility of a qualified operator. A qualified operator has read and

understands the implement and tractor Operator’s Manuals and is experienced in implement and tractor

operation and all associated safety practices. In addition to the safety messages contained in this manual,

safety signs are affixed to the implement and tractor. If any part of the operation and safe use of this

equipment is not completely understood, consult an authorized dealer for a complete explanation.

If the operator cannot read the manuals for themselves or does not completely understand the operation of the

equipment, it is the responsibility of the supervisor to read and explain the manuals, safety practices, and

operating instructions to the operator.

Safe operation of equipment requires that the operator wear approved Personal Protective Equipment (PPE)

for the job conditions when attaching, operating, servicing, and repairing the equipment. PPE is designed to

provide operator protection and includes the following safety wear:

PERSONAL PROTECTIVE EQUIPMENT (PPE)

•

Always Wear Safety Glasses

Hard Hat

Steel Toe Safety Footwear

Gloves

Hearing Protection

Close Fitting Clothing

Respirator or Filter Mask (depends on

operating conditions) OPS-U- 0002