LAP18EULBA
LAP18EULFR
NOTEBOOK CART ASSEMBLY
WITH TIMER
Assembly Instructions for:
INTERIOR E-UNIT
REPOSITIONING / REPLACEMENT
AND
LAP18EULBA
TIMER REPLACEMENT
Parts List
Qty.
1
Part No.
Description
NO TV/MONITOR TO BE
USED ON TOP OF CART
LAP18EULBA Cart Assembly, e-units at back
LAP18EULFR Cart Assembly, e-units at front
Tools Required
Philips screwdriver
MAXIMUM WEIGHT OF ACCESSORIES
ON TOP OF CART: 25 LBS.
The socket-outlet to be installed near the equipment and to be easliy accessible.
Do not load each electrical unit with more than 12 A and do not load any
recepticle with more than 12 A.
LAP18EULFR
NOTE:
UNPLUG CART (TIMER) POWER CORD FROM POWER
SOURCE BEFORE STARTING
CAUTION: RISK OF ELECTRICAL SHOCK.
DO NOT PLUG INTO ANOTHER RELOCATABLE
POWER TAP.
E-UNIT REPOSITIONING:
'FRONT TO REAR'
SEE DETAIL'B'
SEE DETAIL 'A'
bottom shelf
Step 1
Open both front doors of cart to access E-Units. From underneath the bottom shelf, carefully unplug the power
cords of the E-Units from the timer assembly (see Front View) and unclip the power cords from the side panel
clips. Loosen the screw holding the E-Unit bracket assembly and remove all 4 bracket assemblies (see DETAILS
'A' and 'B').
Download from Www.Somanuals.com. All Manuals Search And Download.
front-left
front-right
Step 2
Remove front-left E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior
shelf channel and set it aside.
Remove front-right E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior
shelf channel and set it aside.
DETAIL 'C'
Step 3
Remove 16 screws (2 per shelf) from rear panel that secure the 8 interior shelves (see DETAIL'C').
Download from Www.Somanuals.com. All Manuals Search And Download.
mounting
tab
DETAIL 'D'
Step 4
Remove each interior shelf by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'D',
then carefully sliding out. Set each shelf aside.
Download from Www.Somanuals.com. All Manuals Search And Download.
clip
Step 5
Reinstall the E-Units (set aside from being removed from the front) as follows:
1. Rotate the E-Unit 180 degrees (from original position).
2. Cross over to opposite corner of cart.
3. Tilt in and set bottom in back corner.
4. Grip the top and tilt to the upright position.
When repositioned correctly, the E-Unit outlets face the interior and power switch should be visible from rear
panel cutout.
Reinstall the E-Unit bracket assemblies (make sure that the top flange of the E-unit is aligned with the slot in the
bracket assembly) and tighten screws securely.
Plug in the E-Units power cords into the bottom outlets of the timer assembly.
(Note that the 'A', 'B' designation of the cords are now opposite the timer 'A, 'B' designation set at the factory.
This will not affect the operation of your cart.)
Press each E-Unit power cord into the single wire clip located at the rear/bottom of the cart only.
Fold the power cords into a 's' pattern, flat on the bottom surface.
Download from Www.Somanuals.com. All Manuals Search And Download.
notch
tab
Step 6
Reinstall the 8 interior shelves as follows:
1. Carefully slide in the shelf with notch at the bottom position (the notch will rest on the bracket tab).
(Make sure that the shelf flanges are ALL seated into the mounting tabs.)
2. Slide in all remaining shelves into position as the bottom shelf.
DETAIL 'E'
Step 7
Reinstall 16 screws to rear panel that will secure the 8 interior shelves
(see DETAIL 'E). DO NOT OVER TIGHTEN SCREWS.
Installation is now complete and ready for use.
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE:
UNPLUG CART (TIMER) POWER CORD FROM
POWER SOURCE BEFORE STARTING
E-UNIT REPOSITIONING:
'REAR TO FRONT'
DETAIL 'A'
Step 1
Remove 16 screws (2 per shelf) from rear panel that secure the 8 interior shelves (see DETAIL'A').
mounting
tab
DETAIL 'B'
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 2
With both doors open, remove each interior shelf by carefully pushing upward (to release shelf from mounting
tabs) shown in Detail 'B', then carefully sliding out. Set each shelf aside.
E-Unit power
cord
clip
timer assembly
Front View
Carefully unplug the power cords of the E-Units from the timer assembly (see Front View) and unclip the power
cords from the clips at the rear of cart. Loosen the screw holding the E-Unit bracket assembly and remove all 4
bracket assemblies (see DETAILS 'D' and 'E').
Download from Www.Somanuals.com. All Manuals Search And Download.
DETAIL 'D'
DETAIL 'E'
rear-left
rear-right
Step 3
Remove rear-left E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior
shelf bracket and set it aside.
Remove rear-right E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior
shelf bracket and set it aside.
Download from Www.Somanuals.com. All Manuals Search And Download.
notch
tab
Step 4
Reinstall the 8 interior shelves as follows:
1. Carefully slide in the shelf with notch at the bottom position (the notch will rest on the bracket tab).
(Make sure that the shelf flanges are ALL seated into the mounting tabs.)
2. Slide in all remaining shelves into position as the bottom shelf.
DETAIL 'F
Step 5
Reinstall 16 screws to rear panel that will secure the 8 interior shelves
(see DETAIL 'F'). DO NOT OVER TIGHTEN SCREWS.
Download from Www.Somanuals.com. All Manuals Search And Download.
clip
offset
Step 6
Reinstall the E-Units (set aside from being removed from the rear) as follows:
1. Rotate the E-Unit 180 degrees (from original position).
2. Cross over to opposite corner of cart.
3. Tilt in and set against offset of bottom panel (of cart).
4. Grip the top and tilt to the upright position.
When repositioned correctly, the E-Unit outlets face the interior and power switch should face the front.
Reinstall the E-Unit bracket assemblies (make sure that the top flange of the E-unit is aligned with the slot in the
bracket assembly) and tighten screws securely.
Plug in the E-Units power cords into the bottom outlets of the timer assembly.
(Note that the 'A', 'B' designation of the cords are now opposite the timer 'A, 'B' designation set at the factory.
This will not affect the operation of your cart.)
Press each E-Unit power cord into the two wire clips located on the side panel, bottom.
Do not use the rear, bottom wire clip.
Installation is now complete and ready for use.
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE:
UNPLUG CART (TIMER) POWER CORD FROM
POWER SOURCE BEFORE STARTING
E-UNIT REPLACEMENT:
'REAR LOCATION'
DETAIL 'A'
Step 1
Remove 16 screws (2 per shelf) from rear panel that secure the 8 interior shelves (see DETAIL'A').
mounting
tab
DETAIL 'B'
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 2
With both doors open, remove each interior shelf by carefully pushing upward (to release shelf from mounting
tabs) shown in Detail 'B', then carefully sliding out. Set each shelf aside.
E-Unit power
cord
clip
timer assembly
Front View
Carefully unplug the power cord(s) of the E-Unit(s) from the timer assembly (see Front View) and unclip the power
cord(s) from the clip(s) at the rear of cart. Loosen the screw holding the E-Unit bracket assembly and remove
each bracket assembly (see DETAILS 'C' and 'D').
Download from Www.Somanuals.com. All Manuals Search And Download.
DETAIL 'C'
DETAIL 'D'
rear-left
rear-right
Step 3
Remove E-Unit(s) by griping the top and tilt it side ways until it clears the underside of the cart interior shelf
bracket and set it aside.
Download from Www.Somanuals.com. All Manuals Search And Download.
clip
Step 4
Carefully install replacement E-Unit(s) into position by placing bottom in first and tilting in sideways to the top.
When repositioned correctly, the E-Unit(s) outlets face the interior and power switch should be visible from rear
panel cutout.
Reinstall the E-Unit bracket assemblies (make sure that the top flange of the E-unit is aligned with the slot in the
bracket assembly) and tighten screws securely.
Plug in the E-Units power cord(s) into the bottom outlet(s) of the timer assembly.
Press E-Unit power cord(s) into the single wire clip located at the rear/bottom of the cart only.
Fold the power cords into a 's' pattern, flat on the bottom surface.
Download from Www.Somanuals.com. All Manuals Search And Download.
notch
tab
Step 5
Reinstall the 8 interior shelves as follows:
1. Carefully slide in the shelf with notch at the bottom position (the notch will rest on the bracket tab).
(Make sure that the shelf flanges are ALL seated into the mounting tabs.)
2. Slide in all remaining shelves into position as the bottom shelf.
DETAIL 'E'
Step 6
Reinstall 16 screws to rear panel that will secure the 8 interior shelves
(see DETAIL 'E). DO NOT OVER TIGHTEN SCREWS.
Installation is now complete and ready for use.
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE:
UNPLUG CART (TIMER) POWER CORD FROM
POWER SOURCE BEFORE STARTING
E-UNIT REPLACEMENT:
'FRONT LOCATION'
SEE DETAIL'B'
SEE DETAIL 'A'
bottom shelf
Step 1
Open both front doors of cart to access E-Unit(s). From underneath the bottom shelf, carefully unplug the power
cord of the E-Unit(s) from the timer assembly (see Front View) and unclip the power cord(s) from the side panel
clips. Loosen the screw holding the E-Unit bracket assembly and remove (2) bracket assemblies of the E-Unit(s)
to be replaced (see DETAILS 'A' and 'B').
E-Unit power
cord
timer assembly
bottom shelf
Front View
Download from Www.Somanuals.com. All Manuals Search And Download.
clip
bracket
assembly
bracket
assembly
DETAIL 'A'
DETAIL 'B'
Step 2
Remove E-Unit(s) by griping the top and tilt it side ways until it clears the underside of the cart interior shelf
channel and set it aside.
Download from Www.Somanuals.com. All Manuals Search And Download.
bottom shelf
Step 3
Carefully install replacement E-Unit(s) into position by placing bottom in first and tilting it in sideways to the top.
When repositioned correctly, the E-Unit(s) outlets face the interior and power switch should face the front.
Reinstall the E-Unit bracket assemblies (make sure that the top flange of the E-unit is aligned with the slot in the
bracket assembly) and tighten screws securely.
Plug in the E-Unit power cord(s) into the bottom outlet(s) of the timer assembly (located underneath bottom
shelf).
Press E-Unit power cord(s) into the two wire clips located on the side panel, bottom.
Do not use the rear, bottom wire clip.
Installation is now complete and ready for use.
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE:
UNPLUG CART (TIMER) POWER CORD FROM
POWER SOURCE BEFORE STARTING
TIMER REPLACEMENT:
'E-UNIT AT REAR LOCATION'
DETAIL 'A'
Step 1
Remove 6 screws (2 per shelf) from rear panel that secure the 3 bottom interior shelves (see DETAIL'A').
mounting
tab
DETAIL 'B'
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 2
With both doors open, remove the 3 bottom interior shelves by carefully pushing upward (to release shelf from
mounting tabs) shown in Detail 'B', then carefully sliding out. Set each shelf aside.
E-Unit power
cord
clip
timer assembly
Front View
Carefully unplug the power cords of the E-Units from the timer assembly (see Front View).
Download from Www.Somanuals.com. All Manuals Search And Download.
bottom flange-
timer/bracket
Step 3
Remove 2 screws from bottom flange (securing bracket to bottom of cart) and remove timer/bracket assembly.
Step 4
Remove 2 screws that secure timer to bracket.
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 5
Install replacement timer with 2 screws. Adjust timer dial to current time. If necessary, adjust timer
charging times to match the original timer.
bottom flange-
timer/bracket
Step 6
Install replacement timer/bracket assembly onto bottom, rear of cart with 2 screws. Feed the power cord from
the timer out the grommeted hole (with cord wrap bracket located above cutout). Make sure timer face is aligned
with rear panel cutouts.
Plug in the E-Units power cords into the bottom outlets of the timer assembly.
Download from Www.Somanuals.com. All Manuals Search And Download.
notch
tab
Step 7
Reinstall the 3 interior shelves as follows:
1. Carefully slide in the shelf with notch at the bottom position (the notch will rest on the bracket tab).
(Make sure that the shelf flanges are ALL seated into the mounting tabs.)
2. Slide in remaining 2 shelves into position as the bottom shelf.
DETAIL 'C'
Step 8
Reinstall 6 screws to rear panel that will secure the 3 interior shelves
(see DETAIL 'C'). DO NOT OVER TIGHTEN SCREWS.
Installation is now complete and ready for use.
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE:
UNPLUG CART (TIMER) POWER CORD FROM
POWER SOURCE BEFORE STARTING
TIMER REPLACEMENT:
'E-UNIT AT FRONT LOCATION'
SEE DETAIL 'B'
SEE DETAIL 'A'
bottom shelf
Step 1
Open both front doors of cart to access E-Units. From underneath the bottom shelf, carefully unplug the power
cord of the E-Units from the timer assembly (see Front View) and unclip the power cords from the side panel clips.
Loosen the screw holding the E-Unit bracket assembly and remove all 4 bracket assemblies (see DETAILS 'A' and
'B').
E-Unit power
cord
timer assembly
bottom shelf
Front View
Download from Www.Somanuals.com. All Manuals Search And Download.
clip
bracket
assembly
bracket
assembly
DETAIL 'A'
DETAIL 'B'
front-left
front-right
Step 2
Remove front-left E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior
shelf channel and set it aside.
Remove front-right E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior
shelf channel and set it aside.
Download from Www.Somanuals.com. All Manuals Search And Download.
DETAIL 'A'
Step 3
Remove 6 screws (2 per shelf) from rear panel that secure the 3 bottom interior shelves (see DETAIL 'A').
mounting
tab
DETAIL 'B'
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 4
With both doors open, remove the 3 bottom interior shelves by carefully pushing upward (to release shelf from
mounting tabs) shown in Detail 'B', then carefully sliding out. Set each shelf aside.
bottom flange-
timer/bracket
Step 5
Remove 2 screws from bottom flange (securing bracket to bottom of cart) and remove timer/bracket assembly.
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 6
Remove 2 screws that secure timer to bracket.
Step 7
Install replacement timer with 2 screws. Adjust timer dial to current time. If necessary, adjust timer
charging times to match the original timer.
Download from Www.Somanuals.com. All Manuals Search And Download.
bottom flange-
timer/bracket
Step 8
Install replacement timer/bracket assembly onto bottom, rear of cart with 2 screws. Feed the power cord from
the timer out the grommeted hole (with cord wrap bracket located above cutout). Make sure timer face is aligned
with rear panel cutouts.
notch
tab
Step 9
Reinstall the 3 interior shelves as follows:
1. Carefully slide in the shelf with notch at the bottom position (the notch will rest on the bracket tab).
(Make sure that the shelf flanges are ALL seated into the mounting tabs.)
2. Slide in remaining 2 shelves into position as the bottom shelf.
Download from Www.Somanuals.com. All Manuals Search And Download.
DETAIL 'C'
Step 10
Reinstall 6 screws to rear panel that will secure the 3 interior shelves
(see DETAIL 'C'). DO NOT OVER TIGHTEN SCREWS.
bottom shelf
Step 11
Carefully reinstall E-Units into position by placing bottom in first and tilting it in sideways to the top (underneath
the channel bracket of the cart top panel).
When repositioned correctly, the E-Units outlets face the interior and power switch should face the front.
Reinstall the E-Unit bracket assemblies (make sure that the top flange of the E-unit is aligned with the slot in the
bracket assembly) and tighten screws securely.
Plug in the E-Unit power cords into the bottom outlets of the timer assembly (located underneath bottom shelf).
Press E-Unit power cords into the two wire clips located on the side panel, bottom.
Do not use the rear, bottom wire clips.
Installation is now complete and ready for use.
Download from Www.Somanuals.com. All Manuals Search And Download.
LABEL INSTALLATION:
$8;ꢈꢉꢀ
$8;ꢈꢉꢁ
ꢊ
$8;ꢈꢉꢅ
$8;ꢈꢉꢄ
ꢋ
$8;ꢈꢉꢊ
ꢀ
$8;ꢈꢉꢋ
ꢅ
peel off and attach corresponding labels to
shelves and E-Units.
ꢁ
ꢄ
ꢃ
ꢇ
ꢂ
ꢀꢆ
ꢀꢋ
ꢀꢇ
ꢅꢅ
ꢅꢄ
ꢊꢆ
ꢀꢀ
ꢀꢅ
ꢀꢊ
ꢀꢃ
ꢅꢀ
ꢅꢁ
ꢅꢂ
ꢀꢁ
ꢀꢄ
ꢀꢂ
ꢅꢆ
ꢅꢊ
ꢅꢋ
ꢅꢃ
ꢅꢇ
suggested installation of labels
shelf
shelf
E-Unit
E-Unit
E-Unit at front
E-Unit at rear
suggested label direction
Download from Www.Somanuals.com. All Manuals Search And Download.
PAD LOCK - DOOR:
Open Lock The First Time
1) Set the combination to 0-0-0-0
2) Depress shackle and pull open.
To Set You Own Combination
**REMEMBER: Combination can only be set when lock is open.
1) Insert “reset” tool (included in package) in hole on side of lock.
2) Push key in and turn key 90 degrees in either direction.
(Key automatically stays in this position).
Failure to exert force while pushing key in will result in a failed
attempt to set or reset combination.
3) Set wheels to desired combination.
4) Turn and remove reset tool. Lock is now set to new combination.
**BE SURE TO RECORD YOUR COMBINATION.
5) To lock scramble the wheels and close the shackle.
6) To reopen dial your combination and depress shackle.
Bretford
Bretford Ltd.
11000 Seymour Avenue
Franklin Park, IL 60131
TEL: 847.678.2545
800.521.9614
Technology House
2 Etongate, 110 Windsor Road
Slough, Berkshire SL1 2JA England
TEL: 01753 53 99 55
FAX: 847.678.0852
800.343.1779
FAX: 01753 53 94 78
Part #031-6565
Rev. 08.29.05 CH
Download from Www.Somanuals.com. All Manuals Search And Download.
|