Installation
Instructions
COMBI5500
17" Chase-Mounted Five-Sided
Stainless Steel Combination Unit
Table of Contents
Combination Unit Dimensions . . . . . . . . . . . . . . . .2
Rough-Ins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3–4
Wall-Mounting Instructions . . . . . . . . . . . . . . . . . . .5
Supply, Drain and Waste Connections . . . . . . . . . . .6
Cleaning and Maintenance for Stainless Steel . . . . .6
IMPORTANT
Bradley Security Fixtures are tamper
resistant. All mounting hardware provided is
essential for properly anchoring the unit.
Bradley cannot assume any responsibility
for any improperly installed units.
Read this entire installation manual to
ensure proper installation, then file it with
the owner or maintenance department.
Product warranties may be found under
“Product Information” on our web site at
Compliance and conformity to local codes
and ordinances is the responsibility of the
installer.
215-329 Rev. J; EN 04-732C
© 2004 Bradley Corporation
P.O. Box 309, Menomonee Falls, WI USA 53052-0309
PHONE 1-800-BRADLEY FAX (262) 251-5817
Page 1 of 6
6/28/04
Download from Www.Somanuals.com. All Manuals Search And Download.
17" Chase-Mounted Five-Sided Stainless Steel combination Unit
COMBI5500
Installation Instructions
Installation Instructions
Supplies Required:
• 1" NPT supply piping to flush valve
• Toilet/Lav waste connections
• For optional air valve manifold or self-closing valve: 1/2" NPT supply piping
• For optional Touch Time™ solenoid valve:
1/8" NPT supply piping
Wire nuts sized for 22 AWG wire to connect to 24 VAC power source
Step 1: Roughing-In Supplies, Drain, and Waste Outlet
1. Rough-in wall opening using one of the three versions shown in Figure 1 on page 4.
2. Rough-in water supply(s) for lavatory:
• 1/2" NPT connection required when piping in for air valve manifold (length of tubing
supplied). For air valve manifold assembly installation, refer to Bradley Installation Manual
(part no. 215-1158) provided with the manifold assembly.
• 1/2" NPT connection required when piping in for self-closing valve. For self-closing valve
assembly installation, refer to Bradley Installation Manual (part no. 215-581) provided with
the self-closing valve assembly.
• 1/8" NPT connection required when piping in for Touch Time™ solenoid valve. (Note:
Length of tubing supplied.) For Touch Time™ solenoid valve installation, refer to Bradley
Installation Manual (part no. 215-1378) for Touch Time™ solenoid valve assembly .
3. Rough-in a 1-1/4" or 1-1/2" NPT (size dependent on options ordered) lavatory waste outlet at
the dimensions shown in Figure 1.
4. Rough-in a 1" NPT supply inlet to flush valve.
5. Rough-in a toilet waste outlet at the dimension shown in Figure 1 (waste outlet size dependent
on options ordered).
Bradley Corporation • 215-329 Rev. J; EN 04-732C
6/28/04
3
Download from Www.Somanuals.com. All Manuals Search And Download.
17" Chase-Mounted Five-Sided Stainless Steel combination Unit
COMBI5500
Installation Instructions
Installation Instructions continued . . .
NOTES:
15"
(381mm)
1. All views are from fixture side; right-hand
unit shown.
7-1/2"
(190mm)
2. Top of integral toilet seat to be mounted
15" (381 mm) above finished floor.
3. On floor outlet waste units, centerline of
waste is 4-1/4" (108 mm) from wall.
WALL
OPENING
4. Dimensions shown in parentheses are in
millimeters.
31"
(787mm)
11-1/4"
(286mm)
20"
(508mm)
23-3/4"
(603mm)
FINISHED FLOOR
4" (102mm)
One Wall Opening
7/8" (22mm) Dia.
(5) Holes
15" (381mm)
Sleeve Size
2" x 16"
(51mm x 381mm)
4" x 4"
(102mmx 102mm)
9"
(229mm)
3" x 5"
(76mm x 127mm)
31-1/2"
(800mm)
Sleeve Size
34-1/2"
(876mm)
23-3/4"
(603mm)
7"
(178mm)
7-3/4"
(197mm)
23-3/4"
(603mm)
20"
(508mm)
17-1/2"
(444mm)
20"
(508mm)
15"
(381mm)
Top of
Integral
Seat
11-1/4"
8"
(203mm)
SQUARE
11-1/4"
(286mm)
(286mm)
14"(356mm)
4-1/2"
(114mm)
FINISHED FLOOR
FINISHED FLOOR
Individual Wall Opening
Opening With Sleeve
Figure 1
4
6/28/04
Bradley Corporation • 215-329 Rev. J; EN 04-732C
Download from Www.Somanuals.com. All Manuals Search And Download.
17" Chase-Mounted Five-Sided Stainless Steel combination Unit
COMBI5500
Installation Instructions
Installation Instructions continued . . .
Step 2: Mounting Unit to Wall
NOTE: Refer to Figure 2 when mounting unit. Unit is shown without valves and filler for clarity.
1. Insert six 1/2"-13 threaded studs (supplied by installer) into the back of the unit and screw in
approximately 1/2".
2. Connect the 1-1/2" flush valve supply pipe (supplied by installer) to the 1-1/2" NPT inlet half
coupling located on the back of the fixture.
3. Sliding studs and pipes through the wall openings, position the fixture in place (top of integral
toilet seat is 15" above finished floor).
4. Secure the fixture to the wall using anchor brackets, washers, and nuts provided.
NOTE: All fasteners must be securely tightened to approximately 30 ft./lbs.
VALVE MOUNTING
PLATE
(159-292)
MOUNTING
CHANNEL
(140-558)
1/2"-13 THREADED STUD
0"-4" WALL (109-039)
4"-8" WALL (109-040)
8"-12" WALL (109-048)
WASHER
(142-002AM)
NUT
(110-119)
Figure 2
Bradley Corporation • 215-329 Rev. J; EN 04-732C
6/28/04
5
Download from Www.Somanuals.com. All Manuals Search And Download.
17" Chase-Mounted Five-Sided Stainless Steel combination Unit
COMBI5500
Installation Instructions
Installation Instructions continued . . .
Step 3: Making Supply, Drain, and Waste Connections
NOTE: Flush all supply lines before making connections.
1. Make the water supply connection to the flush valve (piping supplied by installer).
2. Make the lavatory drain connections to the P-trap or elbow (piping supplied by installer).
3. Make the toilet waste outlet connections (piping supplied by installer).
4. Mount the valve assembly in the appropriate location and make the supply connections. Refer to
the appropriate valve installation manual for actual assembly procedure (refer to Step 1,
Procedure #2 on page 3 for installation manual part numbers).
5. Turn on the water supplies to the unit and check for leaking.
6. Press the lavatory pushbuttons several times to purge air from the lines.
7. Activate the flush valve several times to purge air from the lines.
Cleaning and Maintenance Instructions for Stainless Steel
Stainless steel is extremely durable, and maintenance is simple and inexpensive. Proper care, particularly under
corrosive conditions, is essential. Always start with the simplest solution and work your way toward the more
complicated. Daily or as often as needed use a solution of warm water and soap, detergent, or ammonia. Apply
the cleaning solution per the manufactures instructions and always use a soft cloth or sponge to avoid damaging
the finish. To remove stains from stainless steel use a stainless steel cleaner and polish such as Ball® stainless
steel cleaner or a soft abrasive. Always follow the manufactures instructions and apply in the same direction as
the polish lines.
IMPORTANT: NEVER USE ORDINARY STEEL WOOL OR STEEL BRUSHES ON
STAINLESS STEEL. ALWAYS USE STAINLESS STEEL WOOL OR
STAINLESS STEEL BRUSHES.
Special Situations for Material
To remove fingerprints or smears use a high quality stainless steel cleaner and polish in accordance with the
manufactures instructions. Many of these products leave a protective coating the helps prevent future smears and
fingerprints. To remove grease and oil use a quality commercial detergent or caustic cleaner. Apply in
accordance to the manufactures instructions and in the direction of the polish lines. Avoid prolonged contact
with chlorides (bleaches, salts), bromides (sanitizing agents), thiocyanates (pesticides, photography chemicals,
and some foods), and iodides on stainless steel equipment, especially if acid conditions exist.
IMPORTANT: DO NOT PERMIT SALTY SOLUTIONS TO EVAPORATE AND DRY ON
STAINLESS STEEL.
The appearance of rust streaks on stainless steel leads to the belief that the stainless steel is rusting. Look for the
actual source of the rust in some iron or steel particles which may be touching, but not actually a part of the
stainless steel structure.
NOTE: Strongly acidic or caustic cleaners may attack the steel causing a reddish film to appear. The use of
these cleaners should be avoided. Use of brand names is intended only to indicate a type of cleaner. This
does not constitute an endorsement, nor does the omission of any brand name cleaner imply its inadequacy.
Many products named are regional in distribution, and can be found in local supermarkets, department and
hardware stores, or through your cleaning service. It is emphasized that all products should be used in
strict accordance with package instructions.
6
6/28/04
Bradley Corporation • 215-329 Rev. J; EN 04-732C
Download from Www.Somanuals.com. All Manuals Search And Download.
|