®
TTW Series
Through-The-Wall Gas Water Heaters
SERVICE
MANUAL
Troubleshooting Guide
and Instructions for Service
(To be performed ONLY by
qualified service providers)
Models Covered
by This Manual:
M1TW40S*F (BN,CX,SX)
M1TW50S*F (BN,CX,SX)
M1TW60T*F (BN,CX,SX)
M4TW40T*F (BN,SX)
M4TW50T*F (BN,SX)
M4TW60T*F (BN,SX)
M2TW50T*F (BN,CX,SX)
M2TW65T*F (BN,CX,SX)
TW450S65F (B,C,S)*(N,X)
TW465S65F (B,C,S)*(N,X)
(*) Denotes Warranty Years
Manual 238-46238A-00A
Save this manual for future reference
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION
WARNING: If the information in these instructions
is not followed exactly, a fire or explosion may
result causing property damage, personal injury, or
death.
Incorrect operation of this appliance
may create a hazard to life and
property and will nullify the warranty.
FOR YOUR SAFETY
Do not store or use gasoline or other flammable,
combustible, or corrosive vapors and liquids in the
vicinity of this or any other appliance.
DANGER
Do not store or use gasoline or other
flammable, combustible, or corrosive
vapors and liquids in the vicinity of this
or any other appliance.
WHAT TO DO IF YOU SMELL GAS
Do not try to light any appliance.
IMPORTANT
Do not touch any electrical switch; do not use any
phone in your building.
Before proceeding, please inspect the
water heater and its components for
possible damage. DO NOT install any
water heater with damaged
Immediately call your gas supplier from a neighbor's
phone. Follow the gas supplier's instructions.
If you cannot reach your gas supplier, call the fire
department.
components. If damage is evident
then please contact the supplier where
the water heater was purchased or the
manufacturer listed on the rating plate
for replacement parts.
Installation and service must be performed by a qualified
installer, service agency or the gas supplier.
WARNING
WARNING
Water heaters are heat producing appliances. To
DO NOT ATTEMPT TO LIGHT ANY GAS APPLIANCE
IF YOU ARE NOT CERTAIN OF THE FOLLOWING:
Liquefied petroleum gases/propane gas and natural
gas have an odorant added by the gas supplier that
aids in the detection of the gas.
avoid damage or injury, do not store materials
against the water heater or vent-air intake system.
Use proper care to avoid unnecessary contact
(especially by children) with the water heater and
vent-air intake components. UNDER NO
CIRCUMSTANCES MUST FLAMMABLE
Most people recognize this odor as a “sulfur” or
“rotten egg” smell.
MATERIALS, SUCH AS GASOLINE OR PAINT
THINNER BE USED OR STORED IN THE VICINITY
OF THIS WATER HEATER, VENT-AIR INTAKE
SYSTEM OR IN ANY LOCATION FROM WHICH
FUMES COULD REACH THE WATER HEATER OR
VENT-AIR INTAKE SYSTEM.
Other conditions, such as “odorant fade” can cause
the odorant to diminish in intensity, or ”fade”, and not
be as readily detectable.
If you have a diminished sense of smell, or are in
any way unsure of the presence of gas, immediately
contact your gas supplier from a neighbor's
telephone.
Gas detectors are available. Contact your gas supplier,
or plumbing professional, for more information.
CAUTION
If sweat fittings are to be used DO NOT apply heat to
the nipples on top of the water heater. Sweat the
tubing to the adapter before fitting the adapter to the
water connections. It is imperative that heat is not
applied to the nipples containing a plastic liner.
WARNING
FAILURE TO INSTALL AND MAINTAIN A NEW, LISTED
3/4” X 3/4” TEMPERATURE AND PRESSURE RELIEF
VALVE WILL RELEASE THE MANUFACTURER FROM
ANY CLAIM THAT MIGHT RESULT FROM EXCESSIVE
TEMPERATURE AND PRESSURES.
WARNING
Hydrogen gas can be produced in an operating
water heater that has not had water drawn from the
tank for a long period of time (generally two weeks or
more). Hydrogen gas is extremely flammable. To
prevent the possibility of injury under these
conditions, we recommend the hot water faucet to be
open for several minutes at the kitchen sink before
you use any electrical appliance which is connected
to the hot water system. If hydrogen is present,
there will be an unusual sound such as air escaping
through the pipes as hot water begins to flow. Do
not smoke or have open flame near the faucet at the
time it is open.
CAUTION
Turn off or disconnect the electrical power supply to the
water heater before servicing. Label all wires prior to
disconnection when servicing controls. Wiring errors
can cause improper and dangerous operation. Verify
proper operation after servicing.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
The new Bradford White TTW1, TTW2 & TW4 water heaters are designed to provide reliable
performance with enhanced standard features. New design features include reliable spark to
pilot ignition system, enhanced diagnostics, simplified servicing, significantly quiet operation
and additional vent lengths.
Spark to Pilot Ignition System - employing the spark to pilot ignition system promotes
reliable and consistent pilot and main burner ignitions to provide hot water on demand.
Integrated Immersion Thermostat/Gas Control Valve with LED - was developed for ease
of troubleshooting by providing simple diagnostic codes to pinpoint an installation or
component performance issue.
New Powerful Blower - will eliminate problems with difficult venting situations.
Quieter and Cooler Blower Operation - blower noise is significantly reduced for both
interior and exterior environments. Cooler operation increases blower life by reducing bearing
wear and noise.
Rugged Wiring Connections - receptacle type connections promote error free wiring.
Increased Vent Lengths - increased venting performance is achieved while maintaining
Energy Factor & FHSR performance.
The TTW1 (M1TW), TTW2 (M2TW) & TW4 water heaters use a combustion system were
flue gases are combined with dilution air to reduce the flue gas temperature in the blower. The
diluted flue gases are evacuated to the exterior through low temperature vent materials. The
gas control maintains water temperature, ignition sequence and regulates gas flow. A safety
circuit consisting of a pressure switch and blower temperature switch verifies proper conditions
exist for safe and reliable operation. If a situation outside of normal operating parameters
exists, the gas control diagnostic LED will flash a code to positively identify an operational
issue.
This service manual is designed to facilitate problem diagnosis and enhance service efficiency.
To further promote quicker service times the new gas valve can be removed and replaced
without draining the water heater. A special tool is required and will be provided with each gas
valve kit shipped from our Service Parts department.
Please read the service manual completely before attempting service on this new series of
power vent models.
4
4
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Use This Manual
It is intended for this manual to be used by qualified service personal for the primary purpose of
troubleshooting and repair of the Bradford White TTW Series water heaters. Understanding the
sequence of operation section of this manual will contribute greatly to troubleshooting the water
heater.
The Honeywell WV4460E Electronic Gas Control will display error codes in the event of abnormal
operation. Error codes are listed in the troubleshooting chart beginning on page 13 of this service
manual. The troubleshooting chart will also indicate the probable cause for the error code and
direct the service professional to a service procedure to properly diagnose the abnormal operation.
In some difficult to diagnose conditions, it may be necessary to isolate the heater from the vent
system to determine the problem.
Contact the Bradford White technical support group immediately if diagnosis can not be made
using the methods described in this service manual.
Manometer:
Multi-Meter:
A liquid “U” tube type or a digital (magna-helic) type can be used. This
device is used to measure gas and/or air pressure and vacuum.
A digital type is strongly recommended. This device is used to measure
electrical values. The meter you select must have the capability to
measure volts AC, volts DC, Amps, micro-amps and ohms.
Electronic Probes:
In some cases, standard multi-meter probes will damage or simply
not be effective to obtain certain voltage and ohm reading. It will be
necessary to have special electronic “pin” type multi-meter probes.
These probes are available at most electronic wholesale outlets.
Thermometer:
Used to measure water temperature. An accurate thermometer is
recommended.
Water Pressure Gage:
Used to measure water supply pressure. Also used to determine tank
pressure by adapting to the drain valve of the heater.
Gas Control Service Tool: BWC part number 239-45991-00. A specialized tool designed to remove
the gas control from gas control thermal well. Available from
your Bradford White parts supplier.
Various Hand Tools:
Pipe wrench, channel locks, open end wrenchs (3/8",7/16",½"),
12" crescent wrench, Allen wrench set, screw drivers (common &
Phillips), ¼" nut driver, pliers (common & needle nose), socket set, side
cutters wire cutters, wire strippers, wire crimpers, torpedo level, small
shop vac, step ladder, and flashlight, 5 gallon pail.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Power supply
Dedicated 115VAC, 60 Hz, 15A
Gas Supply Pipe
Approved Gas Type
Gas Pressure
Minimum 1/2" NPT (schedule 40 black iron pipe recommended)
Natural or Propane. Unit must match gas type supplied.
5.0" W.C. min. for Nat gas, 11.0" W.C. min. for L.P. gas, 14.0" W.C. maximum (Nat. & L.P.)
Power vent through the wall or vertical through the roof
Venting System
Approved Vent Materials PVC, CPVC or ABS
Minimum Clearance
18" from top, 24" from front, 4" sides and rear.
for Servicing
Water Supply Pressure
150 PSI maximum allowable working pressure. Check local codes for supply pressure
Residential 188°F (87°C), Commercial 199°F (93°C)
Thermal well TCO Limit
Residential Temperature
Set Point Range
60°F (16°C) to 160°F (71°C) (Approximate temperatures)
Commercial Temperature
Set Point Range
80°F (27°C) to 180°F (82°C) (Approximate temperatures)
Blower Temperature
Switch
Normally closed, opens @ 165°F (74°C), auto reset @ 130°F (54°C).
TTW1 (M1TW) Models:
Normally open, closes on vacuum increase @ -.68, opens on vacuum decrease @ -.65
TTW1 (M4TW) Models:
Normally open, closes on vacuum increase @ -.83, opens on vacuum decrease @ -.80
Pressure switch
TTW2 (M2TW & TW4) Models:
Normally open, closes on vacuum increase @ -1.28, opens on vacuum decrease @ -1.25
TTW1 (M1TW & M4TW) Models:
115VAC, 60Hz, 3.1 amps, 3000 RPM, [email protected]" W.C.
Blower
TTW2 (M2TW & TW4) Models:
115VAC, 60Hz, 3.1 amps, 3000 RPM, [email protected]" W.C.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Vent Tables
Venting Specifications for:
40 Gallon
50 Gallon
60 Gallon
2" Diameter (5.1 cm) PVC Vent Connector Lengths
# of
Elbows
Maximum Straight Minimum Straight
Terminating
Length ft (m)
Length ft (m)
Through the Wall
Through the Wall
Through the Wall
Through the Wall
1
2
3
4
45 (13.7)
40 (12.2)
35 (10.7)
30 (9.2)
2 (.6)
2 (.6)
2 (.6)
2 (.6)
Through the Roof
Through the Roof
Through the Roof
Through the Roof
Through the Roof
0
1
2
3
4
50 (15.2)
45 (13.7)
40 (12.2)
35 (10.7)
30 (9.2)
7 (2.1)
7 (2.1)
7 (2.1)
7 (2.1)
7 (2.1)
3" Diameter (7.6 cm) PVC Vent Connector Lengths
# of
Maximum Straight Minimum Straight
Terminating
Elbows
Length ft (m)
115 (35.0)
110 (33.5)
105 (32.0)
100 (30.5)
95 (29.0)
Length ft (m)
Through the Wall
Through the Wall
Through the Wall
Through the Wall
Through the Wall
1
2
3
4
5
10 (3.1)
10 (3.1)
10 (3.1)
10 (3.1)
10 (3.1)
Through the Roof
Through the Roof
Through the Roof
Through the Roof
Through the Roof
0
1
2
3
4
120 (36.6)
115 (35.0)
110 (33.5)
105 (32.0)
100 (30.5)
15 (4.6)
15 (4.6)
15 (4.6)
15 (4.6)
18 (5.5)
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Vent Tables
Venting Specifications for:
48 Gallon
65 Gallon
3" Diameter (7.6 cm) PVC Vent Connector Lengths
# of
Elbows
Maximum Straight Minimum Straight
Terminating
Length ft (m)
Length ft (m)
Through the Wall
Through the Wall
Through the Wall
Through the Wall
1
2
3
4
55 (16.8)
50 (15.2)
45 (13.7)
40 (12.2)
2 (.6)
2 (.6)
2 (.6)
2 (.6)
Through the Roof
Through the Roof
Through the Roof
Through the Roof
0
1
2
3
60 (18.3)
55 (16.8)
50 (15.2)
45 (13.7)
7 (2.1)
7 (2.1)
7 (2.1)
7 (2.1)
4" Diameter (10.2 cm) PVC Vent Connector Lengths
# of
Elbows
Maximum Straight Minimum Straight
Terminating
Length ft (m)
Length ft (m)
Through the Wall
Through the Wall
Through the Wall
Through the Wall
Through the Wall
1
2
3
4
5
175 (53.3)
170 (51.8)
165 (50.3)
160 (48.8)
155 (47.2)
10 (3.1)
10 (3.1)
10 (3.1)
10 (3.1)
12 (3.6)
Through the Roof
Through the Roof
Through the Roof
Through the Roof
Through the Roof
0
1
2
3
4
180 (54.9)
175 (53.3)
170 (51.8)
165 (50.3)
160 (48.8)
15 (4.6)
15 (4.6)
15 (4.6)
15 (4.6)
15 (4.6)
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Control Timings
Ignition State
Timing
Pre-purge
2 Seconds
90 Seconds
3 Seconds
15 Seconds
Trial for Ignition
Flame Stabilization Period
Inter-purge
Flame Failure Response Time
Post-purge
1.5 Seconds (2 second. Maximum; 1 second minimum.)
15 Seconds
PS Fault Delay (failed open/close)
Soft Lockout
Retry after 2 Minutes
Retry after 5 Minutes
TCO Limit Lockout
Indefinite (See Page 24 to reset)
Retry after 2 Minutes (repeats 5 times)
Indefinite (cycle power to reset)
Indefinite (self clears if fault clears for at least 15 seconds)
Verify Resistive Delay
Simulated Resistive Load Lockout
Hardware Error Lockout
Wiring Diagram
Blower
Motor
Blower
Temperature
Switch
Pressure
Switch
Blower
Housing
Pilot
C
B
A
Flammable
Vapor
Sensor
Thermal
Well
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Sequence of Operation
1
2
Start Up.
Upon power up, the control runs a safe-start check with a typical start-up delay of 5 seconds.
Flammable Vapor.
To assure no outputs are energized if the “Flammable Vapor Sensor” is out of range, the control will test the
“Flammable Vapor Sensor” for proper operating range. If the “Flammable Vapor Sensor” is within range the
control resumes normal operation with no perceptible delay. If the “Flammable Vapor Sensor” is out of range,
the control LED immediately flashes 7 times with 3 second pause.
1
Thermostat calls for heat.
Prior to energizing blower, gas control checks safety circuit to insure the circuit is open. Normal switch positions
in the safety circuit are as follows:
a) Pressure switch normally open.
b) Blower temperature switch normally closed.
If the safety circuit is closed, the control waits 4 seconds, gas control LED flashes 2 times with 3 second pause.
Gas control waits 2 minutes then, blower runs for 30 seconds. This cycle repeats until safety circuit opens.
2
3
Blower energizes.
Pressure switch proves blower/vent system operation.
If the pressure switch does not close within 30 seconds, the control LED Flashes 3 times with 3 second pause.
The blower runs for 30 seconds every 2 minutes trying to get the pressure switch or blower temperature switch to
close. This cycle repeats as long as there is a call for heat.
4
5
Blower pre-purge period (2 seconds)
Trial for pilot ignition (90 seconds).
a) The gas control lights the pilot by activating spark igniter and gas flow to pilot burner.
b) If flame is not sensed within 90 seconds, igniter and gas flow are deactivated, blower will post purge and
control LED flashes 6 times with 3 second pause.
6
Main burner Ignition
After pilot flame is sensed, gas control activates main valve for main burner ignition. The gas control will ignore
flame and pressure switch signals for 3 seconds allowing for main burner to stabilize.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Sequence of Operation
Steady state operation.
7
During Steady State Operation the Control Monitors:
Thermostat temperature sensor- When set point temperature is satisfied, gas valve is shut down and
blower will post purge for 15 seconds. Control LED flashes a short flash once every 4 seconds (idle) status
code.
Pressure switch / Blower temperature switch- If either switch opens, pilot valve and main valve is shut
down. The blower continues to runs for 30 seconds attempting to closethe circuit. The control LED Flashes
3 times with 3 second pause.
Flame Sensor- If flame is lost, pilot & main valve are shut down, blower runs for 15 seconds. Control attempts
to re-light pilot 4 times. If unsuccessful, Blower is shut down and control proceeds to 5 minute lockout. Control
re-attempts to light pilot starting at normal heating sequence #2.
8
9
Thermostat satisfies
(Control LED flashing once every 4 seconds).
Burner off.
Blower post purge (15 seconds).
10
1. Flammable Vapor Sensor Fault:
a) If the resistance is greater than 70,000 Ohms - the gas control immediately turns off all outputs. Control waits
and monitors resistance for 30 seconds. If the resistance is greater than 65,000 ohms after 30 seconds, the
gas control proceeds to verify resistive delay for 2 minutes and flashes 7 times then once with a three second
pause. This process is repeated 5 times until the control either returns to normal operation or proceeds to
flammable vapor lockout.
b) If the resistance is below 3000 ohms - The gas control immediately turns off all outputs and proceeds to flash
8 times then once with three second pause. The error self clears if the resistance returns to normal range for at
least 15 seconds.
2. Temperature Sensor Fault:
a) Temperature sensor detected open circuit - The gas control Immediately turns off all outputs and proceeds to
flash 8 times then three times with three second pause. The error self clears if the fault clears for at least 15 seconds.
b) Thermal well sensors not reading the same temperature within 5.5 °F - The gas control Immediately turns off
all outputs and proceeds to flash 8 times then three times with three second pause. The error self clears if the fault
clears for at least 15 seconds.
c) Water temperature in excess of TCO (Temperature Cut Off) limit - The gas control immediately turns off pilot
main valve and proceeds to flash 4 times with 3 second pause. Blower continues to run until gas control is reset.
To reset control, rotate knob of temperature control to the minimum setting for at least 6 seconds before returning
to desired temperature setting.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Sequence of Operation
3. Pressure Switch/Blower Temperature Fault:
a) Pressure switch closed at start of call for heat - The gas control waits four seconds then, proceeds to flash
2 times with 3 second pause. The control waits 2 minutes and then turns on blower for 30 seconds. The blower
turns off after 30 seconds and the control waits for pressure switch to open. Any time the Pressure switch opens,
the blower turns on (or stays on) and the control proceeds to waiting for pressure switch to close.
b) Pressure switch or blower temperature switch failed to close- The gas control runs the blower for 30 seconds
waiting for the pressure switch and/or blower temperature switch to close. If either switch does not close in 30
seconds, the blower turns off and the control flashes 3 times with 3 second pause. The gas control waits two
minutes before turning on the blower for another 30 seconds to see the circuit close. This cycle repeats as long as
there is a call for heat or until the circuit closes.
c) Pressure switch or blower temperature switch opens during burner operation - The gas control turns off the
pilot and main valve, runs blower for 15 seconds (inter-purge) waiting for pressure switch and/or blower
temperature switch to close. If either switch fails to close, the control proceeds as described in 3b above. If the
circuit closes again by the end of the inter-purge, the recycle counter is incremented, if the recycle count has
not reached its limit (4), another trial for ignition begins. If the recycle count has been reached, the gas control
turns off the blower and flashes 6 times then 2 times with 3 second pause. The gas control waits 5 minutes before
repeating ignition sequence.
4. Trial For Ignition Fault:
a) Pressure switch opens during trial - The gas control turns off igniter and pilot valve. The gas control proceeds
as described in 3b above. If the pressure switch closes within 30 seconds the gas control will continue with trial for
ignition starting at blower pre-purge.
b) Flame Not Sensed - The gas control energizes the spark igniter attempting to light the pilot and prove flame. If
flame is not sensed within 90 seconds, the igniter turns off, the pilot valve is closed and the gas control runs the
blower through post purge and flashes 6 times then once with 3 second pause. The control waits 5 minutes before
repeating the ignition sequence.
5. Flame Sensing Fault:
b) Flame lost during run - The gas control turns off pilot and main valves, runs blower for 15 seconds (inter purge).
The gas control increments the recycle count, if the recycle count has not reached its limit (4), another trial for
ignition begins. If the recycle count has been reached, the gas control turns off the blower and flashes 6 times
then 3 times with 3 second pause. The gas control waits 5 minutes before repeating the ignition sequence.
c) Flame sensed out of sequence - the gas control only looks for pilot flame when the blower is running. If flame is
present when the pilot valve is not open, the gas control proceeds to wait for flame loss and flashes 5 times with 3
second pause. This continues until flame is lost, once the flame signal is lost, the control flashes 6 times then 4
times with 3 second pause. The control waits 5 minutes before repeating the ignition sequence.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Green LED
Indicator
Observe green LED indicator on
Electronic gas control. Error flash codes
are displayed with a three second pause
before repeating. Check and repair the
system as noted in the troubleshooting
table below.
Control
Status
Service
Procedure
LED Status
Probable Cause
None, control LED not No electrical
Control power switch in “OFF” position.
Supply voltage interrupted.
Turn power on
on or flashing
power
Stand-by mode,
Waiting for call for Temperature demand is satisfied
heat (no fault).
Normal operation.
Adjust thermostat to
temp level
Short flash, once every
four seconds
Normal operation.
Adjust thermostat to
temp level
“Heartbeat”, alternates Thermostat calling
Tank temperature below set point of thermostat.
bright/dim
for heat (no fault).
1. Unstable pilot.
1. Page 15
Weak pilot signal 2. Pilot tube block or restricted.
Short flash once per
second
on last call for
heat.
3. Oxidation build up on pilot electrode.
4. Wire damage to pilot assembly or bad
connection at gas valve.
2-4. Page 17
Pressure switch
not working-
closed position.
1. Pressure switch tubing kinked or blocked.
2. Blocked pressure tap on switch or blower.
3. Faulty pressure switch.
Two flash, three
second pause
Page 18
1. Vent blockage or improper vent configuration.
2. Pressure switch tubing kinked or blocked.
3. Faulty pressure switch.
1. Check vent or vent tables.
2 & 3 Page 18
Pressure switch
or blower temp.
Three flash, three
second pause
switch not working 4. Blower not spinning up to speed.
4. Page 20
-open position.
5. Blower temp or exhaust temp too high
6. Faulty blower temperature switch.
5 & 6 Page 22
Excessive tank
temperature.
System must be
reset. (See Pg. 24)
1. Thermal well sensor out of calibration.
2. Faulty gas control.
1. Page 24
Four flash, three
second pause
2. Replace gas control,
page 24
3. Pluming leak.
4. Tank not filled with water.
Undesired-false
pilot flame
present.
Five flash, three
second pause
Replace gas control,
page 24
1. Pilot valve stuck in open position.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Control
Status
Service
Procedure
LED Status
Probable Cause
1. Unstable pilot.
Failed to light
pilot.
System auto
resets.
1. Page 15
2. Pilot tube blocked or restricted.
3. Oxidation build up on pilot electrode.
4. Wire damage to pilot assembly or bad
connection at gas valve.
Six-one flash, three
second pause
2-4. Page 17
1. Check vent or vent tables.
Pressure switch
or blower temp
switch opened
during burner
operation.
System auto
resets.
1. Vent blockage or improper vent configuration.
2. Pressure switch tubing kinked or blocked.
3. Faulty pressure switch.
2 & 3 Page 18
Six-two flash, three
second pause
4. Refer to venting section of
installation manual
4. Vent termination being affected by wind
5. Blower not spinning up to speed.
5. Page 20
6. Blower temp or exhaust temp too high
7. Faulty blower temperature switch.
6 & 7 Page 22
1. Unstable pilot.
1. Page 15
2. Pilot tube blocked or restricted.
3. Oxidation build up on pilot electrode.
4. Wire damage to pilot assembly or bad
connection at gas valve.
Pilot flame
extinguished.
System auto
resets.
Six-three flash, three
second pause
2-4. Page 17
5. Refer to installation manual
5. Insufficient combustion air.
6. Gas pressure is out of specification.
Undesired-false
pilot flame
sensed.
System auto
resets.
Six-four flash, three
second pause
Replace gas control,
page 26
Pilot valve stuck in open position.
Flammable
Vapor Sensor
fault detected.
WARNING: EXPLOSION HAZARD
Seven flash, three
second pause
• Indicates gasoline vapors were detected at potentially
explosive levels.
Page 28
• Verify no gasoline vapors are still present.
• Reset the control by cycling power to the appliance or by
cycling the ON/OFF switch.
• Replace the Flammable Vapor Sensor element if a gasoline
spill event occurred.
Flammable
Vapor Sensor
out of
• Very Flammable Vapor Sensor (FVS) resistance is not below
25 KΩ.
• Check wiring to FVS and insure it is not shorted.
Eight-one flash, three
second paus
Page 28
Page 24
• Replace control if everything above checks out OK.
specification.
Thermal well
sensor damaged
or unplugged
Eight-three flash, three
second pause
1. Damage to thermal well wire.
2. Thermal well sensor resistance out of range.
1. Interrupt power supply
2. Replace gas control,
page 26
Eight-four flash, three
second pause
Gas valve fault
detected.
1. Control needs to be reset.
2. Control is wet or physically damaged.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
TTW SERVICE PROCEDURE I
Burner Operation Inspection,
Adjustment, Cleaning and Replacement
Burner Inspection and Air Shutter Adjustment.
At periodic intervals (every 6 months) a visual inspection should be made of the pilot and main burner for proper
operation and to assure no debris is accumulating.
Pilot flame should be stable, some causes for an unstable pilot flame are:
a) Water heater vent is less than the allowable vent length.
b) Gas pressure is out of specification.
c) Pilot flame not fully engulfing spark/flame sensor.
Main burner should light smoothly from pilot and burn with a blue flame with a minimum of yellow tips.
Steel burner models self adjust air to gas ratio mixture and do not have an adjustable air shutter. Cast iron burner can
have the gas and air mixture properly proportioned by adjusting the air shutter on the mixer face of the main burner
(see cast iron burner adjustment below).
Main burner must be free from any debris accumulation that may effect burner operation (see burner cleaning
procedure on page 16).
Cast Iron Burner Air Shutter Adjustment
WARNING
Inner door and burner components may be HOT when performing this operation. Take
necessary precaution to prevent personal injury.
Step 1.
With main burner in operation, remove outer jacket door and inner door per service procedure XIII on
page 34.
Step 2.
To adjust for proper burning, loosen the air shutter nut, rotate the air shutter to close the opening in the
burner, then slowly rotate the air shutter open until flame becomes as blue as possible with a minimum of
yellow tips. Tighten the air shutter nut.
Too much air will cause the flame to lift off the burner ports and create noisy burner operation.
Too little air will result in soot formation.
Step 3.
Reinstall inner door and observe burner operation. Burner should operate as adjusted in step 2. If not,
repeat air shutter adjustment compensating for proper burner operation with inner door closed.
Air Shutter Nut
AirShutter
15
Download from Www.Somanuals.com. All Manuals Search And Download.
TTW SERVICE PROCEDURE I
Burner Operation Inspection,
Adjustment, Cleaning and Replacement
Burner Cleaning
Burner Cleaning
Step 1.
Position gas control power switch to the
“OFF” position and unplug heater from wall
outlet.
Step 2.
Turn off gas supply to water heater.
Step 3.
Remove outer jacket door and inner door per service
procedure XIII on Page 34.
Igniter/flame
sense wire
Step 4.
Disconnect pilot tube (7/16 wrench) and
feedline (¾ wrench) from gas control.
Feedline nut
Step 5.
Disconnect igniter/flame sensor wire from gas control.
Step 6.
Remove burner assembly from combustion chamber.
Pilot tubing nut
Step 7.
Thoroughly inspect burner surface area and burner port area and
remove any loose debris.
Burner
surface area
Burner
port area
Main burner
orifice
Step 9.
Unscrew burner from main burner
orifice. On cast iron burners, loosen
air shutter nut and unscrew feedline
from burner.
Step 10. Remove main burner orifice from
feedline (½" wrench on steel
burners, 3/8" wrench on cast iron)
inspect orifice, clean or replace if
necessary.
Step 11. Reassemble burner and reinstall into water heater. Restore gas supply
and check for gas leaks.
L.P. Main burner
orifice. Left hand
thread
Step 12 To resume operation follow the instruction located on the lighting
instruction label or the lighting instruction located in the installation
and operating manual.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
TTW SERVICE PROCEDURE II
Pilot testing, Cleaning and Replacement
Pilot Inspection, Testing and Replacement
Step 1.
Position gas control power switch to the
“OFF” position and unplug heater from wall
outlet.
Step 2.
Step 3.
Turn off gas supply to water heater.
Remove outer jacket door and inner door per service
procedure XIII on page 34.
Igniter/flame
sense wire
Step 4.
Disconnect pilot tube nut (7/16 wrench) and feedline nut
(¾ wrench) from gas control.
Feedline nut
Pilot tubing nut
Step 5.
Step 6.
Disconnect igniter/flame sense wire from gas control.
Remove burner assembly from combustion chamber.
Step 7.
Step 8.
Remove pilot assembly from feedline (¼" nut driver).
Visually inspect igniter/flame sense wire for damage. Replace
pilot if damage is found.
Ferrule
nut
Pilot
Pilot
Pilot
hood
Step 9.
With a multi-meter set to the ohms setting, check continuity
through igniter/flame sense wire. Replace pilot if no continuity.
tubing orifice
Step 10. Visually inspect igniter/flame sense electrode for deterioration.
Replace pilot as necessary. Electrode should not be in contact
with pilot hood, If so, carefully adjust electrode to a gap
distance of 3/32" (.09) from pilot hood.
Igniter/flame
sense wire
Igniter/flame
sense electrode
Step 11. Visually inspect igniter/flame sense electrode for oxidation
build up. Carefully clean any oxidation using very fine emery
cloth.
Step 12. Visually inspect pilot tubing for kinks or cracks. If damage is
found replace pilot.
Step 13. Inspect pilot tubing and pilot orifice for blockage:
a) Remove ferrule nut from bottom of pilot assembly (7/16" wrench).
b) Remove pilot tube and pilot orifice.
c) Inspect pilot tubing and pilot orifice for blockage. Clean
or replace as necessary.
Step 14. Reassemble pilot and install to feedline. Reinstall burner assembly to water heater. Restore gas supply
and check for gas leaks.
Step 15 To resume operation follow the instruction located on the lighting instruction label or the lighting
instruction located in the installation and operating manual.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
TTW SERVICE PROCEDURE III
Pressure Switch Testing and
Replacement
WARNING
Pressure Switch Testing
115 volt potential exposure. Use caution
making voltage checks to avoid personal injury.
Step 1.
Step 2.
Step 3.
Position power switch on gas control
to the “OFF” position.
Remove the three screws (Phillips screw driver) from control access cover on blower assembly and
remove cover (see photo 1).
Carefully remove pressure switch from blower housing (see photo 2)
1
2
With steps 1,2 & 3
Pressure Switch
complete,
disconnect wire leads from
pressure switch.
Pressure switch
wire leads
Slide pressure switch in direction
of arrow while tilting slightly away
from blower housing.
Use a multi-meter set to the
ohms setting. With blower off,
check across pressure
switch terminals.
Are switch contacts open?
(no electrical continuity)
Check tubing and pressure
tap on switch for blockage.
Is there blockage?
Replace switch
(see page 19)
N
N
Y
Y
Clear blockage
Position gas valve power
switch to the “ON” position
and adjust thermostat
to call for heat,
this will start the blower.
Check with multi-meter, do
pressure switch contacts
close with blower running?
Y
Y
Y
Check tubing and
pressure tap on
switch for blockage.
Is there blockage?
Is vent system length
Is vent
system
blocked
See blower testing
within vent table
specifications
N
N
N
Y
(page 20)
Is blower OK?
listed on pages 7 & 8
N
N
Y
Reconfigure vent
system to be
compliant with
vent tables.
Correct blower
problem.
Switch contacts are OK.
See safety circuit trace
(page 29)
18
Download from Www.Somanuals.com. All Manuals Search And Download.
TTW SERVICE PROCEDURE III
Pressure Switch Testing and
Replacement
WARNING
115 volt potential exposure. Use caution
to avoid personal injury.
Pressure Switch Replacement
Step 1.
Position gas control power switch
to “OFF” position.
Step 2.
Remove the three screws (Phillips screw driver) from control access cover on blower assembly and
remove cover (see photo 3).
Pressure Switch
3
4
Step 3.
Carefully remove pressure
switch from blower
housing (see photo 4)
Slide pressure switch in direction
of arrow while tilting slightly away
from blower housing.
6
5
Step 4.
Step 5.
Disconnect tubing from
pressure switch.
(see photo 5)
Disconnect yellow wires
from pressure switch
(see photo 6)
Step 6.
Step 7.
Step 8.
Step 9.
Reconnect wires from step 5 to new pressure switch.
Reconnect tubing to new pressure switch.
Carefully position pressure switch into blower housing.
Position gas control power switch to “ON” position and verify proper heater operation.
Step 10. Replace control access cover from step 2.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
TTW SERVICE PROCEDURE IV
Blower Testing and Replacement
WARNING
Blower Testing
115 volt potential exposure. Use caution when
making voltage checks to avoid personal injury.
Step 1.
Position gas control power switch
to “ON” position and adjust control to call for heat.
7
Step 2.
Remove the three screws (Phillips Screw driver)
from control access cover on blower assembly and
remove cover (see photo 7).
Remove exhaust
adapter
Connect
Disconnect vent
system from top of
blower and remove
vent adapter.
Disconnect
pressure switch
tubing from blower.
(see photo 8)
manometer to
pressure tap of
blower.
Does blower energize
Within 2 minutes?
Y
(see photo 8)
(see photo 10)
10
N
Pressure tap
8
9
With blower running, and exhaust
adapter removed from top of
blower, is there a negative
Y
Blower OK
pressure of -2.15" to -2.30" W.C.?
N
Pressure
switch tubing
Is there 115vac across
blue and green wires
(see photo 13)
N
Determine voltage
problem and correct.
Y
Replace blower
Does blower energize after
2 minutes, run for 30
seconds and shut down?
See pressure
switch testing
Page 18
Y
11
12
N
Disconnect cord set
shown in photo 9. Is
there 115VAC across
terminals shown in
photo 11
Is there 115VAC
across terminals
Y
Y
shown in photo 12 ?
Reconnect cord set
shown in photo 9, is
there 115VAC between
blue wire and green
ground wire
N
Y
Replace blower
N
Incorrect supply
voltage polarity
(see photo 13)
N
Green ground
wire
Does cord set
Determine
13
Replace
cord set
N
have electrical
N
Y
Is there 115 VAC
at wall outlet?
power source
problem and
correct.
continuity?
Y
Blue wire
Y
Replace
gas control
Check power cord
for damage.
Repair or replace
power cord
N
Shown with pressure
switch removed.
Replace blower
20
Download from Www.Somanuals.com. All Manuals Search And Download.
TTW SERVICE PROCEDURE IV
Blower Testing and Replacement
Blower removal
Step 1.
Step 2.
Position gas control power switch to the “OFF” position.
Unplug blower power cord from wall outlet.
Remove exhaust
adapter and retain for
use on new blower.
Step 3.
Step 4.
Disconnect vent system from exhaust adapter on top of
blower.
Blower Mounting
Screws
Remove exhaust adapter from blower (blade screw driver)
and retain for use on new blower
Step 5.
Step 6.
Unplug cord sets from blower.
Remove the three blower mounting screws
(¼" nut driver).
Step 7.
Remove blower with gasket from water heater.
Blower
Cord Sets
Blower Installation
Step 8.
Clean any debris from jacket head of water heater.
Step 9.
Set new blower with gasket in place using locating pins on
blower flange to line up with location holes in jacket head.
Be sure not to damage gasket.
Step 10 Secure blower in place using mounting screws from step 6.
Step 11. Re-install exhaust adapter from step 4.
Locating Pins
on blower flange
Step 12. Reconnect vent system to
exhaust adapter.
Pin location holes in
Step 13. Reconnect cord sets from step 5.
jacket head
Step 14. Plug blower power cord into wall outlet.
Step 15. Position gas control power switch to the “ON” position.
Step 16. Verify proper blower operation.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
TTW SERVICE PROCEDURE V
Blower Temperature Switch Testing
and Replacement
Blower Temperature Switch
Testing.
WARNING
115 volt potential exposure. Use caution
to avoid personal injury.
Step 1.
Position power switch on gas control
to the “OFF” position.
14
Step 2.
Remove the three screws (Phillips screw driver) from
control access cover on blower and remove cover (see
photo 14).
Step 3.
Locate blower temperature switch (see photo 15)
15
Switch Setting
Blower temperature
switch location
Opens on rise @ approximately 165°F
Auto resets on fall @ approximately 130°F
Cool switch to
below 130°F
Air mixing inlet
Disconnect wire leads to
N
switch. Using a multi-meter
set to the ohms setting, is
there continuity between
the switch terminals?
Replace switch
(see page 23)
Y
Common causes for
N
Reconnect wire leads and
observe heater operation.
Do exhaust gas
high exhaust temperature
Exhaust
temperature is
too hot.
1. Vent length is below minimum allowable.
2. Vent diameter not to specification.
3. Restricted dilution air inlet.
4. Missing or deteriorated flue baffle.
5. Gas pressure is out of specification.
Y
Y
Do switch
contacts open?
temperatures rise to or
above 170°F
with vent connected?
N
Do switch
contacts open?
Replace switch
(see page 23)
Y
N
Switch OK
22
Download from Www.Somanuals.com. All Manuals Search And Download.
TTW SERVICE PROCEDURE V
Blower Temperature Switch Testing
and Replacement
Blower Temperature Switch
Replacement.
WARNING
115 volt potential exposure. Use caution
to avoid personal injury.
16
Step 1.
Step 2.
Position gas control power switch to the “OFF” position
and unplug heater from wall outlet.
Remove the three screws (Phillips screw driver) from the
control access cover on blower and remove cover.
(see photo 16)
Step 3.
Locate blower temperature switch (see photo 17)
Disconnect red and yellow wire leads from switch.
17
Blower temperature
switch location
Step 4.
Step 5.
With an appropriate tool such as side cutters, snip the
retaining lug from the blower housing to allow removal of
temperature switch (see photo 18).
Step 6.
Step 7.
Remove switch from blower housing.
18
Install new switch. Be sure switch is properly seated in
mounting area.
Snip retaining lug
from blower housing
Step 8.
Step 9.
Reconnect red and yellows wires to new switch. Wires are
interchangeable with either terminal.
Position gas control power switch to the “ON” position
and verify proper heater operation.
Step 10. Replace control access cover from step 2.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
TTW SERVICE PROCEDURE VI
Gas Control/Thermal Well Testing and
Replacement
Gas Control Testing
See pages 29 & 30 for gas control
voltage testing.
Thermal Well Testing
Disconnect thermal
well wire harness
If Control has gone into TCO lockout due to
excessive tank temperature (four flash, 3 second
pause) reset control by rotating knob of temperature
control to the minimum setting for at least 6 seconds
before returning to desired temperature setting.
Observe heater operation. If control
continues to lockout due to
excessive tank temperature,
proceed to thermal well testing to
determine cause.
19
20
Thermal well testing
Position gas control power switch to
the “OFF” position and disconnect
thermal well harness from gas
control.
CAUTION
DO NOT use standard multimeter probes for this test.
Doing so will damage connector. Use special pin type
electronic probes or small diameter wire pins inserted
into connector.
Using a multi-meter set to the
Ohms setting, determine the
resistance of thermal well sensor
(see caution photos 19 & 20)
Using a multi-meter set to the ohms setting, insert one meter probe (see caution)
into center wire position of thermal well connector, insert the second probe (see
caution) into either of the outside wire positions (see photo 19).
Alternate the probe on the outside position to the opposite outside wire position
(see photo 20).
Once the thermal well resistance values are known, the water
temperature must also be known to determine if the resistance
values are correct. See page 25 to obtain water temperature.
N
Replace thermal well
(see page 26)
Are thermal well resistance values correct?
Y
Replace gas control
(see page 26)
24
Download from Www.Somanuals.com. All Manuals Search And Download.
TTW SERVICE PROCEDURE VI
Gas Control/Thermal Well Testing and
Replacement
WARNING
Stored water may be HOT when performing the following steps in this procedure.
Take necessary precaution to prevent personal injury.
Determine Water Temperature Inside Tank
Note: It is important to understand once the resistance for the thermal well is determined from page 24, water flow
through the heater should not occur. Prior to performing the steps below, turn off the cold water supply to the
water heater. This will prevent cold water flow into the tank affecting the resistance value of thermal well.
Step 1.
Step 2.
Position gas control power switch to “OFF” position.
Draw approximately 1 quart of water from drain valve into container and immediately measure water
temperature using an accurate thermometer. It may be necessary to open a hot water faucet to allow
heater to drain.
Step 3.
Using the chart below, determine correct resistance value for the water temperature from step 2.
Example:
If temperature of water is 84°F, then the resistance through the sensor would be
8449 (see shaded area). NOTE: Sensor resistance increases as the temperature
falls.
Sensor Resistance at Various Temperatures
In Degrees F
°F
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
190
200
0
1
2
3
4
5
6
7
8
9
26109
19906
15314
11884
9299
7333
5827
4663
3758
3048
2488
2043
1688
1402
1170
982
25400
19383
14925
11592
9078
7165
5697
4562
3679
2986
2439
2004
1656
1376
1150
965
24712
18876
14548
11308
8862
7000
5570
4464
3602
2925
2391
1966
1625
1351
1129
949
24045
18383
14180
11032
8653
6839
5446
4368
3527
2866
2344
1928
1595
1327
1110
933
23399
17905
13823
10763
8449
6683
5326
4274
3453
2808
2298
1891
1566
1303
1090
917
22771
17440
13477
10502
8250
6531
5208
4183
3382
2752
2253
1856
1537
1280
1071
901
22163
16990
13140
10248
8057
6383
5094
4094
3312
2697
2209
1820
1509
1257
1053
886
21573
16553
12812
1000
7869
6238
4982
4006
3244
2643
2166
1786
1481
1235
1035
871
21000
16128
12494
9760
7685
6098
4873
3922
3177
2590
2124
1753
1454
1213
1017
857
20445
15715
12185
9526
7507
5961
4767
3839
3112
2538
2083
1720
1427
1191
999
842
713
828
814
801
788
775
762
749
737
725
25
Download from Www.Somanuals.com. All Manuals Search And Download.
TTW SERVICE PROCEDURE VI
Gas Control & Thermal Well Testing
and Replacement
Gas Control & Thermal Well Removal From Water Heater
Control
Step 1.
Step 2.
Step 3.
Step 4.
Step 5.
Position gas valve power switch to the “OFF”
position and Unplug Heater from power supply.
herma
Drain heater to a point below the gas
control level.
Turn off gas supply to water heater and
disconnect gas piping from gas control.
Disconnect wire harnesses and burner assembly
from gas control.
Remove gas control & thermal well by rotating flats of Thermal Well counter clockwise (1-5/16"wrench).
Gas Control Removal From Thermal Well
Follow the steps below allows removal gas control from thermal well without
removing thermal well from tank.
Step 1.
Step 2.
Step 3.
Step 4.
Position gas control power switch to the “OFF” position and unplug water heater from power supply.
Turn off gas supply to water heater and disconnect gas piping from gas control.
Disconnect wire harnesses & burner assembly from gas control.
Using gas control service tool (239-45991-00) available from your BWC parts supplier, Insert tool into
back of gas control (see photos below)
View from back of
control for clarity
Insert tool from
back of control
Service tool shown
inserted in to back
of control
Step 5.
Pivot tool towards heater as far as possible (see photo below). Lift straight up on gas control. The
control should move about 1/8". At this point, remove tool not allowing the control to fall back. With
tool removed, lift straight up on control to remove completely from Thermal Well.
With service tool inserted, pivot tool back towards
heater as far as possible. Lift straight up on control,
control will move 1/8". Remove tool and continue to lift
straight up on control to remove from Thermal Well.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
TTW SERVICE PROCEDURE VI
Gas Control & Thermal Well Testing
and Replacement
Gas Control Assembly to Thermal Well
Step 1.
Install threaded end of thermal well into tank. Be sure
thermal well flange is positioned as shown in photo 24
for proper control alignment.
24
Step 2.
Step 3.
Route wire leads back into relief opening.
(see photo 24)
Align slots located on thermal well flange with tabs
located on back of gas control (see photos 24 & 25)
Route wires
through relief
opening
Thermal well
flange slots
Step 4.
Step 5.
Carefully push control back onto thermal well flange
as far as possible towards water heater. Slide control
down to lock into position.
25
Install burner and connect pilot and feedline to gas
control.
Gas control Tabs
Igniter/sensor
Step 6.
Step 7.
Reconnect wire harnesses to gas control
per the illustration.
connection
Reconnect gas piping to gas control.
Restore gas supply and check for gas
leaks.
Ground Wire
connection
Step 8.
To resume operation, follow the
instruction located on the lighting
instruction label or the lighting instruction
located in the installation and operation
manual.
5 pin
blower harness connection
3 pin
thermal well connection
Flammable Vapor
Sensor
27
Download from Www.Somanuals.com. All Manuals Search And Download.
TTW SERVICE PROCEDURE VII
Flammable Vapor Device Testing
Flammable Vapor Device Testing
Step 1.
Step 2.
Step 3.
Position power switch on gas control to the
“OFF” position.
Disconnect flammable vapor sensor from
gas control.
Using a multi-meter set to the ohms setting
check resistance of flammable vapor sensor.
(see caution below)
Resistance must be within 3,000 ohms and
48,000 ohms. If outside of this range replace
flammable vapor sensor.
Flammable Vapor
Sensor
Multi-meter set to
ohms setting
CAUTION
Electronic
DO NOT use standard multimeter probes for this test.
Doing so will damage connector. Use special electronic
“pin type” probes or small diameter wire pins inserted
into connector.
“pin type”
Meter Probes
Flammable Vapor
Sensor
28
Download from Www.Somanuals.com. All Manuals Search And Download.
TTW SERVICE PROCEDURE VIII
Safety Circuit Voltage Trace
Safety Circuit Voltage
Trace
WARNING
115 volt potential exposure. Use caution
making voltage checks to avoid personal injury.
NOTE: This procedure assumes a cool tank.
26
Remove three screws (Phillips Screw driver) from control access
cover on blower and remove cover (see photo 26).
Position gas control switch to the “ON”
position and adjust thermostat dial to call
for heat, Is there 10 to 13 VAC between
Is LED on gas valve flashing
N
red wire leading to blower temperature
switch and green ground wire?
Blower must be running during this
voltage check.
No voltage from gas control,
call for technical support.
Y
the “heartbeat” code
(alternating bright/dim)
N
(see photo 27)
Y
Verify 115VAC to gas
control (see page 30)
Is there 10 to 13 VAC between yellow
wire leading from pressure switch and
green ground wire?
Is there continuity
Check for loose or
broken wire
connection at switch
terminals
through blower
temperature switch?
(see page 22)
N
Y
(see photo 27)
N
Y
Determine cause of blower
temperature switch
activation and correct.
Correct igniter/
sensor problem.
Check igniter/sensor
(see page 17)
is igniter/sensor OK?
Do you hear or can you
see the igniter sparking?
Faulty cord set or
gas control.
N
Y
Green ground wire
Y
27
Safety circuit
voltage is OK.
Red wire leading to
blower temp. switch
If burner does not light,
observe LED flash code
on gas valve and refer to
troubleshooting section
on page 13
Yellow wire
leading from
pressure switch
29
Download from Www.Somanuals.com. All Manuals Search And Download.
TTW SERVICE PROCEDURE IX
115 VAC Trace
WARNING
115 VAC Circuit Trace
115 volt potential exposure. Use caution
making voltage checks to avoid personal injury.
Step 1. Verify 115VAC and proper polarity at wall outlet.
Step 2. With unit plugged in and control power switch in the “ON” position verify LED status.
LED status
None, Control LED not
on or flashing.
LED status
Short flash, once every
four seconds.
LED status
“Heartbeat”, alternates
bright/dim.
LED status
Various flashing error
codes.
Waiting for
call for heat.
Thermostat calling
for heat
Verify error code as
listed on page 13
29
30
28
Disconnect cord set as
shown in photo 28
Using a volt meter set
to volts AC, is there
115VAC across
Check for damage to
AC supply power cord.
N
Y
Y
Repair damage
terminals shown in
photo 29 ?
N
Y
Replace Blower
Is there 115VAC
across terminals
shown in photo 30 ?
Reconnect cord set
shown in photo 28.
31
N
Disconnect wire harness
from gas control
Incorrect supply
voltage polarity
(see photo 31).
Wire harness
Locate black & white wires at
connector, It may be necessary to pull
back wire sheath to identify wire colors.
(see photo 32)
32
Wire sheath pulled back to
identify wire colors
Is there 115VAC
across black & white
wires as shown in
photo 32?
Replace gas
control.
Y
Check for 115VAC between black & white wires.
-NOTE-
Electronic meter probes required. Use care not to
damage connector during this check.
N
Call for technical
support.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
TTW SERVICE PROCEDURE X
Dip Tube
Inspection and replacement
Dip Tube Inspection and Replacement
WARNING
Water Heater components and stored water may be HOT when performing the following
steps in this procedure. Take necessary precaution to prevent personal injury.
Step 1.
Step 2.
Position on/off switch of gas control valve to “OFF” position and unplug water heater from wall outlet.
Turn off cold water supply to water heater. Connect hose to drain valve of water heater and route to an
open drain. Open a nearby hot water faucet to vent heater for draining. Open drain valve of water
heater and allow heater to drain to a point below the inlet connection nipple.
Step 3.
Step 4
Disconnect inlet nipple from plumbing system.
With an appropriate tool such as a pipe wrench, remove inlet nipple/dip tube from the water heater.
Use caution not to damage pipe threads.
Step 5.
Visually inspect inlet nipple/dip tube. Inlet nipple/dip tube should be free of cracks and any blockage.
Hydro-jet slots should be open and free of any blockage.
Any damage such as cracks, restriction due to deformation or unintentional holes are not field
repairable and the inlet nipple/dip tube must be replaced.
Step 6.
Step 7.
Upon completion of inspection or subsequent replacement, reinstall inlet nipple/dip tube into water
heater. Connect nipple to plumbing system, resume water supply and refill with water.
To resume operation follow the instructions located on the lighting instruction label or the lighting
instructions located in the installation and operation manual.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
TTW SERVICE PROCEDURE XI
Anode
Inspection and replacement
Anode Inspection and Replacement
WARNING
Water Heater components and stored water may be HOT when performing the following
steps in this procedure. Take necessary precaution to prevent personal injury.
Step 1.
Step 2.
Position on/off switch of gas control valve to the “OFF” position and unplug water heater from wall
outlet.
Turn off cold water supply to water heater. Connect hose to drain valve of water heater and route to an
open drain. Open a nearby hot water faucet to vent water heater for draining. Open drain valve of
water heater and allow water heater to drain to a point below the outlet connection nipple.
Step 3.
Step 4
Disconnect outlet nipple from plumbing system.
With an appropriate tool such as a pipe wrench, remove outlet nipple/anode from the water heater. Use
caution not to damage pipe threads.
Step 5.
Visually inspect outlet nipple/anode. Outlet nipple/anode should show signs of depletion, this is
normal. If depletion is ½ of the original anode diameter (approximately ¾” diameter), replacement is
recommended. If any of the steel core of the anode is exposed, replacement is recommended.
Step 6.
Step 7.
Upon completion of inspection or subsequent replacement, reinstall outlet nipple/anode into water
heater. Connect nipple to plumbing system, resume water supply and refill with water.
To resume operation, follow the instructions located on the lighting instruction label or the lighting
instructions located in the installation and operation manual.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
TTW SERVICE PROCEDURE XII
Flue Baffle
Inspection and replacement
Disconnect vent
system from exhaust
adapter.
Remove blower to gain access to
flue baffle
33
Blower Mounting
Screws
Step 1.
Position gas control power switch to the “OFF” position
and unplug blower from wall outlet.
Step 2.
Disconnect vent system from exhaust adapter on top of
blower.
Step 3.
Step 4.
Unplug cord sets from blower. (see photo 33).
Remove the three blower mounting screws
(¼" nut driver) (see photo 33).
Blower
Cord Sets
Step 5.
Step 6.
Step 7.
Remove blower with gasket from water heater.
Remove flue baffle from Heater (see photo 34).
34
Flue Baffle
Inspect baffle for deterioration, missing restrictors.
Clean any scale or debris build up. Replace with new
baffle as necessary.
Step 8.
Step 9
Reinstall baffle into flue tube. Be sure baffle
hanger tab are inserted into notch location at the
top of the flue tube (see photos 35 & 36).
Check Burner to insure no scale has accumulated during
this operation. See burner cleaning procedure on page 15.
35
Step 10. Reinstall blower on water heater. Connect vent
system and cord sets to blower. Plug water heater
into wall outlet.
Step 11. To resume operation follow the lighting instruction
located on the lighting instruction label or the lighting
instruction located in the installation and operation
manual.
Flue tube
notch
36
Baffle shown
installed in flue
tube notch.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
TTW SERVICE PROCEDURE XIII
Inner Door/Gasket Removal, Inspection
Replacement and Reinstallation
Inner Door Removal Procedure
Step 1. Position gas control power switch to the “OFF” position.
Step 2. Remove outer jacket burner access door
Step 3. Inner Door Removal.
a) Remove (2) 1/4" hex drive screws from right side inner door.
b) Remove (2) 1/4" drive screws from flange section of inner door.
c) Remove (2) 1/4" drive screws from left side inner door.
d) Remove inner door and inspect per step 4.
¼" Hex Drive Screws
Right and Left Side Inner Door.
¼" Hex Drive Screws at
Flange Area of Inner Door
Step 4. Fully inspect inner door gaskets for the following:
>Tears
>Other imperfections that will inhibit proper seal
>Gasket adhesion to inner door
>Missing Material
>Cracks
>Material left on combustion chamber (around opening)
>Dirt or debris
If the gasket is not effected by any of the above, gasket replacement is not required. If replacement is
proceed to Inner Door Gasket Replacement Procedure.
required,
Inner Door Gasket Replacement
Procedure.
WARNING
If the information in these instructions is not
followed exactly, a fire or explosion may result causing
property damage, personal injury or death.
Step 5. After inspection of inner door as noted in step 4, completely remove gasket and adhesive residue from right
and left side inner doors as needed.
Step 6. Use RTV sealant (recommended bead size 1/8") to secure the inner door gasket to the inner door sections
(right & left). Refer to illustration on next page for proper application. Note the overlap configuration in the
flange area of the inner door. Set the flange section first, this will help to achieve the proper over lap position.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
TTW SERVICE PROCEDURE XIII
Inner Door/Gasket Removal, Inspection
Replacement and Reinstallation
Installation of Inner Door With Gasket.
WARNING
Step 7.
Clean any residual gasket residue or other debris
from combustion chamber surface before
installing the inner door/gasket assembly.
Stripped fastener connections may allow
for seal breach of inner door. A seal
breach may result in a fire or explosion
causing property damage, personal injury
or death. Do not over tighten screws in
steps 8, 10 and 11.
Step 8.
Place the left side inner door into position first.
Firmly position the radiused channel of the inner
door aroundthe feedline. Using the 1/4” hex drive
screws from step 3c, secure left side inner door in
place. DO NOT OVER TIGHTEN SCREWS.
If a fastener connection is stripped,
contact the manufacturer listed on the
water heater rating plate.
Step 9
Position pilot tube and igniter/sensor wire
against left side inner door flange gasket.
DO NOT ROUTE THROUGH RADIUSED
CHANNEL WITH FEEDLINE.
Position pilot tubing and
igniter/sensor wire.
Radiused Channel
for Feedline
35
Download from Www.Somanuals.com. All Manuals Search And Download.
TTW SERVICE PROCEDURE XIII
Inner Door/Gasket Removal, Inspection
Replacement and Reinstallation
Step 10. Firmly place right side inner door flange against the left side inner door flange and secure with two ¼” drive
screws from step 3b. DO NOT OVER TIGHTEN SCREWS.
Step 11. Align right side inner door to combustion chamber and verify the fastener holes of the combustion
chamber are aligned with the right side inner door slotted opening. Verify seal integrity around
combustion opening. Secure right side inner door using 1/4” hex drive screws from step 3a. DO NOT
OVER TIGHTEN SCREWS. Verify both left and right sides of the inner door are properly positioned and
sealed against the combustion chamber.
Secure flange with
¼" drive screws.
Verify threaded hole
alignment with slotted
openings in inner door.
Step 12. Replace outer jacket burner access door.
Step 13. To resume operation follow the instructions located on the lighting instruction label or the lighting instructions
located in the installation and operation manual.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
ScreenLok® Flame Arrestor Cleaning
ScreenLok® Flame Arrestor Cleaning:
Step 1.
Step 2.
Step 3.
Step 4.
Position Gas Control Power Switch to the OFF position.
Remove outer jacket.
Remove inner door per TTW SERVICE PROCEDURE XIII, step 3a through step 3d.
Disconnect main burner feed line (3/4 wrench), pilot tube (7/16 wrench) and igniter/flame sensor wire
from gas control and remove burner assembly from combustion chamber.
Step 5.
Step 6.
Clean ScreenLok® Flame Arrestor using stiff brush, compressed air and/or shop vacuum to remove any
scale or other debris accumulation. Using a soft brush, clear jacket openings from any dirt, dust,
restrictions or other obstructions.
Remove any debris from burner assembly per TTW SERVICE PROCEDURE I and reinstall burner
assembly into combustion chamber.
Step 7.
Step 8.
Step 9.
Reconnect feedline, pilot tube and igniter/flame sensor wire to the gas control.
Reinstalll inner door per TTW SERVICE PROCEDURE XIII, step 7 through step 12.
To resume operation follow the instructions located on the lighting instruction label or the lighting
instruction located in the installation and operation manual.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary of Terms
BTU
GPM
Hz
KW/h
LED
NPT
Ohms
PSI
British Thermal Units
Gallons per Minute
Hertz
Killo-watts per hour
Light Emitting Diode
National Pipe Thread
Ohms of resistance
Pounds per Square Inch
Revolutions per Minute
Temperature Cut Off
Volts Alternating Current
Inches of Water Column
Degrees Centigrade
Degrees Fahrenheit
RPM
TCO
VAC
W.C.
°C
°F
NOTES
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List
1. Blower Complete
13. Heat Trap Inlet
14. Inlet Dip Tube
15. Wire Harness
16. T&P Valve
37. Brass Drain Valve
25. Cast Iron Burner
26. Pilot Assy. (L.P.)
27. Pilot Orifice (L.P.)
28. Feedline
2. Air Mixing Inlet cover
3. Pressure Switch
38. Flammable Vapor Sensor Clip
39. Flammable Vapor Sensor
40. Sensor Harness
4. Blower Temp. Switch
5. Blower Gasket
17. ¾ NPT Plug
41. Thermal Well
42. Gas Control
43. Gas Control Service Tool
44. Kit-Gas Control
45. Inner Door Gasket Kit
46. ASSE App’vd Mixing Valve
47. Kit-Heat Trap Insert
29. Jam Nut
6. Blower Power Cord
7. Vent Adapter w/vent term.
8. Condensate Hose Kit
9. Flue Reducer (M2 only)
10. Heat Trap Outlet
18. Burner Assy. (Nat)
19. Burner Head
20. Main Burner Orifice
21. Pilot Assy. (Nat)
22. Pilot Orifice
23. Feedline
24. Burner Assy. (L.P.)
30. Air Shutter
31. Main Burner Orifice (L.P.)
32. Outer Door
33. Right Side Inner Door
34. Screw #8-15 x 3/4
35. Left Side Inner Door
36. Screw #10-12 x 3/4
11. Hot Water Outlet Anode
12. Flue Baffle
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Email
Download from Www.Somanuals.com. All Manuals Search And Download.
|