Bracketron Bicycle Accessories MAZ 102 03 User Manual

111004-1  
Part Number: MAZ-102-03  
INSTALLATION INSTRUCTIONS  
MAZDA 6  
(2003-2007)  
NOTE: READ INSTRUCTIONS COMPLETELY BEFORE INSTALLING THIS BRACKETRON PHONE MOUNT.  
All instructions are written from the drivers seat position looking forward at the vehicle dash. We advise caution whenever you are  
removing or handling plastic parts of a vehicles dash. WARNING: Unnecessary force or pressure can cause pieces to crack or break.  
Logo and part number will be right side up and readable when installed.  
TOOLS NEEDED: Dash Trim Tool, (Part #SIT-104), #2 Phillips Screwdriver, 10mm socket and driver.  
PARTS INCLUDED: One Custom Bezel Mount and Instructions.  
LOCATION OF MOUNT: To the right of the air vent.  
Step 1.  
Begin installation by opening the glove box door. Remove the  
cable attached to the right hand side. Push inward on both  
sides of the glove box door and release two tabs. Pull the glove  
10mm Screw  
box off of its hinges and set aside. With the 10mm socket and  
driver, locate and remove the horizontal screw inside the glove  
box cavity. Set the screw aside. Note: See inset in top picture  
for guidance.  
Step 2.  
Apply the emergency brake, unscrew the shift knob and set  
it aside. Use the Dash Trim Tool (Part #SIT-104) to remove the  
bezel that surrounds the emergency brake lever. There are six  
clips that secure this bezel to the center console, and two that  
secure it to the bezel that surrounds the shifter knob. Release  
these clips and set bezel aside. Continue by releasing the bezel  
that surrounds the shift knob. There are two clips on each side  
of this bezel. Disconnect all wiring and set bezel aside.  
Install Mount Here  
Step 3.  
Locate and remove two Phillips screws from underneath the  
climate control. Set the screws aside. With manual climate  
control, remove three control knobs and set aside. Locate and  
remove two Phillips screws from behind the two outside knobs.  
Use the Dash Trim Tool to release three clips from each side of  
the radio. Carefully set the radio on a protective cloth to prevent  
any scratches.  
Step 4.  
Locate and Remove one Phillips screw from the upper right  
corner of the radio cavity and set screw aside. Place Custom  
Bezel Mount over existing screw hole and replace factory  
screw.  
Step 5.  
Carefully reinstall the dash in reverse order securing all wiring,  
clips, and screws. Install any Bracketron phone holder or Amps  
compatible device to your Custom Bezel Mount. Your installa-  
tion is complete.  
2006  
© Bracketron Inc, 2007 All rights reserved.  
The information in this document is subject to change without notice. Bracketron Inc. assumes no responsibility for any errors that may appear in this document nor do we assume any liability in  
connection with its use. This supersedes and voids all previous literature. Please contact the sales department for additional information.  
Bracketron Inc will not be responsible or liable for damage to vehicles in the installation and or removal of this Bracketron Inc mount.  
Bracketron Inc will not be liable for personal injuries or damage to property resulting from a motor vehicle accident and or improper installation of this Bracketron Inc mount.  
Bracketron Inc. 5249 West 73rd Street, Suite G, Edina, MN 55439, Ph: 952-746-7775 Fax: 1-800-660-1784 Toll Free: 1-866-237-4443  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Blanco Indoor Furnishings 157 090 User Manual
Bosch Appliances Refrigerator Bottom Freezer I User Manual
Braun Bathroom Aids C 31S User Manual
Bushnell GPS Receiver 360400 User Manual
Cadillac Automobile 2007 STS User Manual
Canon Camera Lens KT17EX43B User Manual
Canon Copier PC 140 User Manual
Canon Digital Camera SD790 IS User Manual
Carrier Heat Pump 30RA User Manual
Cavalry Storage Computer Drive CADB U34 User Manual