English
CWM7
Download from Www.Somanuals.com. All Manuals Search And Download.
1. CWM7 Carton Contents
2. CWM7 Series Basics
CWM7.3
CWM7.4
1
1
1
1
CWM7.3
• CWM7 Series speaker assembly (baffle, frame/back
box, grille)
• Reservoir box
• Cut-out template
• Paint mask
CWM7 Series in-wall speakers comprise a baffle
carrying the speaker drivers and crossover, an
integrated back-box and front flange, and a
magnetically secured grille. The back box is connected
via external terminals to the speaker cables with the
baffle connecting automatically as it is inserted in the
back box.
• Port plug
• Blanking Plate
• L-shaped push-lock fastener removal tool
• Allen key (CWM7.3 only)
• Document pack containing Quick Start Guide and
Warranty information
A reservoir box can be fitted within the wall either
above or below the back box to enhance the speaker’s
low frequency performance. The CWM7.3 incorporates
a MF/HF baffle that can be rotated 90° to enable the
speaker to be used in landscape orientation for centre
channel applications.
Environmental Information
All Bowers & Wilkins products are
designed to comply with international
directives on the Restriction of Hazardous
Substances (RoHS) in electrical and electronic
equipment and the disposal of Waste Electrical
and Electronic Equipment (WEEE). These symbols
indicate compliance and that the products must be
appropriately recycled or processed in accordance
with these directives. Consult your local waste disposal
authority for guidance.
CWM7 Series speakers require wall aperture
dimensions described in the following table:
Model
Aperture Height
711mm (28 in)
Aperture Width
251mm (9.9 in)
226mm (8.9 in)
187mm (7.4 in)
Reservoir Box Clearance
465mm (18.31 in)
CWM7.3
CWM7.4
CWM7.5
390mm (15.4 in)
331mm (13 in)
465mm (18.31 in)
390mm (15.4 in)
3
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Positioning CWM7 Series Speakers
CWM7.5
All CWM7 Series speakers require a clear depth of
102mm (4.02 in) from the front of the ceiling surface.
The appropriate position for CWM7 Series speakers
within the listening environment will depend on their
specific application:
Multi-channel Audio Applications
For applications where multiple CWM7 Series speakers
are to be used for multi-channel audio visual systems
the left and right front speakers should be located
either side of the screen approximately 0.5m (20 in)
away. The centre channel speaker should be located
either directly above or below the screen or, in the case
of an acoustically transparent screen, directly behind.
Surround channel CWM7 Series speakers should be
located just behind and either side of the listening
position.
Note: The CWM7.3 can also be used in landscape
orientation with aperture dimensions of 251mm
(9.9 in) by 711mm (28 in) respectively height by
width. No reservoir box is used with the CWM7.3 in
landscape orientation.
General Background Audio Applications:
For applications where single CWM7 Series speakers
are required to operate independently to provide
background audio, they can be located substantially as
installation convenience and architecture dictate. The
only acoustic constraint to bear in mind is that corner
locations will result in significantly emphasised low
frequencies and should be avoided.
Note: The reservoir box clearance is the clear
distance within the wall above or below the aperture
required to accommodate the reservoir box.
Try to avoid corner locations for any of the speakers
and to ensure that acoustic environment around each
front and surround speaker is similar.
Before installing CWM7 Series speakers you should
ensure that the wall locations chosen are free of
obstructions such as pipe work, ducting or wiring that
will interfere with the installation. In existing dry-wall
construction, use a stud-finding tool to help you map
the wall construction and a pipe detector to scan the
proposed installation locations.
Stereo Audio Applications:
For applications where a pair of CWM7 Series
speakers is to be used for conventional stereo
reproduction, they should be located between 3m
(10 ft) and 5m (16.5ft) apart and a similar distance
in front of the listening area. Try to avoid corner
locations for the speakers and to ensure that acoustic
environment around each speaker is similar.
Note: Different acoustic environments might be,
for example, a bare wall and a heavily curtained
window.
Note: The nature of the installation of in-wall
speakers means that it is sometimes impractical to
locate them in the acoustically ideal positions. In
these cases they should be located as close as is
practical to the ideal positions. Your local Bowers
and Wilkins retailer will be able to offer advice if
required.
Note: CWM7 Series in-wall speakers will most often
be installed in existing walls, however, if they are
to be installed in newly constructed walls a pre-
mount kit that aids appropriate wall construction is
available. Contact your local Bowers and Wilkins
retailer for more information.
Note: Different acoustic environments might be,
for example, a bare wall and a heavily curtained
window.
Note: CWM7 Series drive units create stray
magnetic fields. We recommend that magnetically
sensitive items such as CRT screens and magnetic
cards for example, are kept at least 0.5m (20 in)
from the speaker. LCD, OLED and plasma screens
are not affected by magnetic fields.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Installing CWM7 Series Speakers
To install a CWM7 Series speaker proceed as
described in the following paragraphs:
4.2 The reservoir box enhances the low frequency
performance of CWM7 Series speakers. It connects
to the top or bottom of the back box via a hinge and
clamp that enables it to be fed into the wall cavity
above or below the back box. CWM7 Series speakers
are shipped set up for the reservoir box to be installed
below the back box. If this is not practical, perhaps
thanks to the encroachment of drywall frame noggin
(horizontal brace), the reservoir box can be swapped
for use above the back box.
4.3 If speaker cable is already present in the wall
space, pull the cable through the aperture. If speaker
cables are not already installed this should be done at
this stage. It is likely that you will need to gain access
through the floor above to route the cables down into
the wall cavity.
4.1 Using the supplied cut-out template, mark a cut
line on the wall. Check the cut line defines the correct
dimensions. Cut along the line with an appropriate tool
to create an aperture in the wall.
Leave enough spare cable through the aperture to
ease connection to the speaker back box, but not so
much that it is likely to buzz or rattle when pushed
back up into the cavity. Approximately 1.0m is
appropriate.
Note: Ensure that there is enough free space
internally adjacent to the aperture for the back box
clamps to rotate fully outwards. 20mm (0.79 in) free
space is required.
Note: An arrow symbol on the back box illustrates
upward orientation.
Note: To reduce the possibility of the ceiling buzzing
or rattling, adhesive mastic can be applied between
the studs and sheetrock in the vicinity of the
speaker aperture.
Note: Always use high quality, low resistance
speaker cable. Low resistance is especially
important if the length of cable from amplifier to
speaker exceeds 5m. Your local Bowers and Wilkins
retailer will be able to offer advice on speaker cable
selection if required.
To swap the reservoir box location, the blanking plate
screwed to the lower inside panel of the back box
must be unscrewed and replaced to cover the hole in
the upper inside panel. Ensure that the thumb screws
securing the blanking plate are adequately tight. The
diagram above illustrates the removal and replacement
of the blanking plate and attachment of the reservoir
box.
We recommend that the reservoir box is always used
if possible, however with a CWM7.3 speaker installed
in landscape orientation, use of the reservoir box is not
possible. If no reservoir box is used a blanking plate
must be fitted to both back box holes.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
4.4 Now connect the speaker cable to the spring
terminals on the side back box, first looping the
cable around the strain relief bar. The diagram above
illustrates cable connection.
4.5 With the back box connected to the cable and its
reservoir box attached it may be inserted into the wall
aperture and cavity. Correct back box orientation must
be established at this stage: the red arrow on the back
box flange should be pointing upwards.
4.6 If the back box flange is to be painted it should be
done at this stage. Any conventional, domestic paint
may be applied by brushing, rolling or spraying. Use
the supplied paint mask to avoid getting paint in the
back box cavity. Painting without using the paint mask
risks contamination of the internal connection terminals
or the grille attachment magnets. The diagram above
illustrates painting using the paint mask.
Ensure that the speaker connection polarity is
correct: the cable connected to the positive terminal
on the amplifier should be connected to the red
spring terminal on the back box. Similarly, the cable
connected to the negative terminal on the amplifier
should be connected to the black spring terminal on
the back box.
Ensure that the clamps are retracted so that they will
pass through the aperture then feed the reservoir box
into the cavity below (or above) the aperture followed
by the back box itself into the aperture. Take care that
the cable is not trapped. When the reservoir box and
back box are adequately seated in place the clamps
can be tightened. The diagram above illustrates
insertion of the reservoir box and back box.
Note: If the grille is to be sprayed this should be
done “off-line” before it is fitted.
Note: If an amplifier is already connected to the
cable it should be switched off while connections
are being made to the back box.
Finally tighten the two thumbscrews to secure and seal
the reservoir box.
Note: If no reservoir box is fitted the back box is
simply inserted straight into the aperture.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
4.7 The baffle can now be inserted into the back box.
The baffle insertion and attachment technique is slightly
different in the case of the CWM7.3 and CWM7.4/5.
In both cases however you should first ensure that the
connector on the baffle is oriented correctly with the
connector inside the back box.
CWM7.3 Baffle Insertion
With the MF/HF baffle in the correct orientation the
baffle assembly can be lifted and inserted in the back
box till it is just sub-flush of the back-box flange. Take
care to ensure that the electrical connector lines up.
The baffle is held in the back box by eight screws.
Tighten the screws to a torque of 1.5Nm. The baffle will
then be secured in the back box.
If the CWM7.3 is to be used in landscape orientation
the MF/HF baffle must be removed and rotated 90°
so the tweeter is uppermost in the installed speaker.
If necessary, this should be done before the baffle is
inserted in the back box.
To rotate the MF/HF baffle first remove the four screws
holding it in place. Now, with your hand gently over
the midrange driver, lean the whole baffle assembly
forward slightly so that the MF/HF baffle begins to fall
out. Do not let it fall completely but return the baffle
to the upright position while holding the MF/HF baffle
out of its rebate. Finally withdraw the MF/HF baffle
completely, turn it 90°, reseat it in the rebate and
replace the four screws. Tighten the screws to a torque
of 1.5Nm. The diagram above illustrates removal and
rotation of the MF/HF baffle.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
CWM7.4 and CWM7.5 Baffle Insertion
4.8 A port plug accessory is included with CWM7
Series speakers. The plug can be used if desired to
reduce bass output by obstructing the speaker’s reflex
port. Simply push the plug into the reflex port. The
diagram above illustrates insertion of the port plug.
The CWM7.4/5 baffle assembly is held in the back
box by a combination of hinge features and push-lock
fasteners. To secure the baffle assembly in the back
box, lift the baffle up to the back box and engage the
two pegs on its lower edge at an angle within the holes
inside the back box flange. Now simply rotate the baffle
inwards so that the electrical connector engages and
the baffle sits just sub-flush of the back-box flange.
The baffle is held in the back box by two push-
lock fasteners. Push-lock fasteners are secured by
pushing the head inwards – either with a thumb or a
screwdriver. As they secure, the fasteners will click
three times. The baffle will then be secure in the back
box. The diagram above illustrates inserting the baffle
and securing the push-lock fasteners.
Note: Push-lock fasteners are unsecured by turning
anticlockwise with a screwdriver. The supplied
L-shaped tool can now be used to hook and lift
behind the fastener head.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
4.9 The grille can now be fitted to the baffle. It is held in
place magnetically so simply needs to be aligned with
the groove in the back box flange where it will click into
place. The diagram above illustrates fitting the grille.
The CWM7 Series speaker is now installed and ready
for use.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
B&W Group Ltd
Dale Road
Worthing West Sussex
BN11 2BH England
B&W Group (UK Sales)
T +44(0)1903221500
Copyright © B&W Group Ltd. E&OE
B&W Group North America
T +19786642870
T +44 (0)1903221800
F +44 (0)1903221801
B&W Group Asia Ltd
T +85234729300
Download from Www.Somanuals.com. All Manuals Search And Download.
|