Download from Www.Somanuals.com. All Manuals Search And Download.
2. HANDLING COMPACT DISCS
MOISTURE CONDENSATION
On a rainy day or in a very damp area, moisture may condense on the lenses inside the unit. Should this
occur, the unit will not operate properly. In such a case, remove the disc and wait for about an hour until
themoisturehasevaporated.
NOTES ON CDs
NOTES ON DISCS
If you use the discs explained below, the sticky
residue can cause the CD to stop spinning and
maycausemalfunctionorruinyourdiscs.
Do not use second-hand or rental CDs that have a
sticky residue on the surface (for example, from
peeled-off stickers or from ink, or glue leaking
fromunderthestickers).
1. A dirty or defective disc may cause sound
dropouts while playing. To enjoy optimum
sound, handlethediscasfollows.
Handle the disc by its edge. To keep the disc
clean, donottouchthesurface(P.1).
There are paste residue.
Ink is sticky (P.5).
****
*******
*******
*******
*******
P. 1
P. 5
2. Donotstickpaperortapeonthedisc(P.2).
Do not use rental CDs with old labels that are
beginningtopeeloff.
Stickers that are beginning
to peel away, leaving a
sticky residue (P.6).
**************
*******
*******
P. 2
*******
P. 6
3. Do not expose the discs to direct sunlight or
heat sources such as hot air-ducts, or leave
them in a car parked in direct sunlight where
Do not use your CDs with labels or stickers
attached.
there can be
temperature inside the car (P.3).
a
considerable rise in
*******
Labels are attached (P.7).
*******
*******
*******
*******
P. 7
Do Not Use Special Shape CDs
Be sure to use round shape CDs only for this
unit and do not use any special shape CDs.
Use of special shape CDs may cause the unit
to malfunction.(P.8).
P. 3
4. Before playing, clean the discs with an
optional cleaning cloth. Wipe each disc from
thecentreout(P.4).
P. 8
Be sure to use CDs with disc mark
RECORDABLE
REWRITABLE
Only for this unit.
P. 4
5. Do not use solvents such as benzine,
thinner,commercially available cleaners, or
antistatic spray intended for analog discs.
CD-Rs and CD-RWs which have not undergone
finalization processing cannot be played. (For
more information on finalization processing,
refer to the manual for your CD-R/CD-RW
writing software or CD-R/CD-RW recorder.)
Additionally, depending on the recording status,
it may prove impossible to play certain CDs
record on CD-R or CD-RW.
E - 2
Download from Www.Somanuals.com. All Manuals Search And Download.
3. INSTALLATION
Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up
properly and the unit and system work properly.
Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts
cancausemalfunctions.
Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the
vehicle.
Install the unit where it does not get in the driver's way and cannot injure the passenger if there is a
suddenstop, likeanemergencystop.
Ifinstallationangleexceeds30°fromhorizontal, theunitmightnotgiveitsoptimumperformance.
30°
Avoid installing the unit where it would be subject to high temperature, such as from direct sunlight, or
from hot air, from heater, or where it would be subject to dust dirt or excessive vibration.
Be sure to remove the front panel before installing the unit.
DIN FRONT/REAR-MOUNT
Thisunitcanbepropertyinstalledeitherfrom“Front”(conventionalDINFront-mount)or“Rear”(DIN
Rear-mount installation, utilizing threaded screw holes at the sides of the unit chassis). For details,
refertothefollowingillustratedinstallationmethodsAandB.
DIN FRONT-MOUNT (Method A)
Installation the unit
1
1. Dashboard
2. Holder
2
3
182
After inserting the half sleeve into the
dashboard, select the appropriate tab according
to the thickness of the dashboard material and
bend them inwards to secure the holder in
place.
53
3. Screw
1
6
1. Dashboard
2. Nut (5mm)
3. Spring washer
4. Screw (5x15mm)
5. Screw
6. Support Strap
7
4
Be sure to use the support strap to secure the
back of the unit in place. The strap can be bent
by hand to the desired angle.
7. Plain washer
5
2
3
E - 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Removing the unit
a
a. Frame
b. Insert fingers into the groove in the front
of frame and pull out to remove the
frame. (When re-attaching the frame,
point the side with a groove down wards
and attach it.)
c. Insert the levers supplied with the unit
into the grooves at both sides of the unit
as shown in figure until they click. Pulling
the levers makes it possible to remove
the unit from the dashboard.
b
c
Trim Plate Installation:
Push the trim plate against the chassis until it is fitted.
You must do this before you install the front panel, otherwise it can't be attached.
DIN REAR-MOUNT (METHOD B)
Installation using the screw holes on the sides of the unit.
Fastening the unit to the factory radio mounting bracket.
1. Select a position where the screw
holes of the bracket and the screw
holes of the main unit become
aligned (are fitted) and tighten the
screws at 2 places on each side.
2
2. Screw
4
3. Factory radio mounting bracket.
4. Dashboard or Console
5. Hook (Remove this part)
5
3
Note: the mounting box, outer trim ring,
and half-sleeve are not used for method
B installation.
2
5
E - 4
Download from Www.Somanuals.com. All Manuals Search And Download.
4. DETACHABLE CONTROL PANEL (D.C.P.)
Removing The Detachable Control Panel (D.C.P.).
1. Turn the power off
2. Press the D.C.P. release button
3. Remove the D.C.P.
PANEL RELEASE
BUTTON
Attaching the DCP
1. Attach the panel at the right side first, with
point B on the main unit touching point A on the
D.C.P. (As shownonthedigram).
2. Then press the left side of D.C.P. onto the main
unituntila“click”soundisheard.
2
A
B
CAUTION
DO NOT insert the D.C.P from the left side. Doing so may damage it.
The D.C.P can easily be damaged by shocks. After removing it, place it in a protective case and be careful not to drop
itorsubjectittostrongshocks.
When the release button is pressed and the D.C.P is unlocked, the car's vibrations may cause it to fall. To prevent
damage to the D.C.P, always store it in a protective case after detaching it.
The rear connector that connects the main unit and the D.C.P is an extremely important part. Be careful not to
damage it by pressing on it with fingernails, pens, screwdrivers, etc.
Note:
If the D.C.P is dirty, wipe off the dirt with soft,
dry cloth only. And use a cotton swab soaked
in isopropyl alcohol to clean the socket on the
back of the D.C.P.
Socket
E - 5
Download from Www.Somanuals.com. All Manuals Search And Download.
5. WIRING DIAGRAM (20 PIN HARNESS PLUG)
ANTENNAJACK
ANTENNAPEXT
ENDERP
CABLE
FUSE
20-PIN
AUDIO/POWER
HARNESS
(See Figure 1)
WHITE
RCA-TO-RCA CABLES
(not supplied)
SUB WOOFER
BLUE
YELLOW
SUB-WOOFER
AUX IN
WHITE
RED
RCA-TO-RCA CABLES
(not supplied)
WHITE
RED
REAR LINE OUT
GREY
AMP
WHITE
FRONT LINE OUT
BLACK
RED
Power Antenna Connect to power antenna or amplifier,If
not used,Tape bare end of wire.
BLUE
Ground Connect to ground terminal or
chassis
Clean unpainted metal part of
BLACK
Memory/Battery
YELLOW
Connect to battery or 12 volt power source that is always live.
The radio will not work if this wire is not connected
RED
Accessory/Ignition Connect to existing radio wire or radio fuse.
20-PIN AUDIO/POWER HARNESS
LEFT FRONT
WHITE-BLACK LF-
RIGHT FRONT
GREY-BLACK RF-
1
2
3
4
5
6
7
8
9
10
20
WHITE LF+
GREY RF+
11
12
13
14
15
16
17
18
19
LEFT REAR
RIGHT REAR
VIOLET-BLACK RR-
GREEN-BLACK-LR
GREEN LR+
VIOLET RR+
Figure 1
Pin View
WIRE COLOR
WIRE COLOR
WHITE
FUNCTION/LABEL
RIGHT FRONT SPEAKER (-)
FUNCTION/LABEL
PIN
1
PIN
LEFT FRONT SPEAKER (+)
LEFT FRONT SPEAKER (-)
GREY/BLACK
GREY
11
12
13
14
15
16
17
18
19
20
RIGHT FRONT SPEAKER (+)
RIGHT REAR SPEAKER (+)
RIGHT REAR SPEAKER (-)
2
WHITE/BLACK
3
VIOLET
POWER ANTENNA
4
VIOLET/BLACK
BLUE
BATTERY(+)
5
YELLOW
BLACK
WHITE
RED
6
GREEN
GREEN/BLACK
RED
LEFT REAR SPEAKER (+)
LEFT REAR SPEAKER (-)
IGNITION(ACC)
CHASSIS GROUND
7
8
LEFT FRONT PRE-AMP LINE OUT
RIGHT FRONT PRE-AMP LINE OUT
FRONT PRE-AMP LINE OUT COMMON
LEFT REAR PRE-AMP LINE OUT
9
BLACK
REAR PRE-AMP LINE OUT COMMON
RIGHT REAR PRE-AMP LINE OUT
BLACK
WHITE
10
RED
E - 6
Download from Www.Somanuals.com. All Manuals Search And Download.
6. BASIC OPERATIONS
1) PANEL RELEASE BUTTON (REL)
Press this button to remove the control panel.
12) POWER ON/OFF BUTTON
Press this button to turn on or off the power.
5) DISPLAY BUTTON (DISP)
Press this button briefly, the LCD will display the clock for about 2 seconds, then return to previous
display mode.
ClockAdjustment
Under clock display mode, press DISP button until the LCD flashes, press Tuning Up Button to adjust
hour and Tuning Down Button to adjust minute.
16) SOURCE BUTTON (SOURCE)
Press this button to select Radio and CD modes.
The available selections depends on version:
Radio CD Player
Radio > CD > AUX in
Sub-woofer On/Off
Press SOURCE button for more than 3 seconds to activate or turn off the Sub-woofer output.
Aux Input
Connect the external signal to the auxiliary line in jack located at the rear of the unit , then
press Source button to select Aux mode. Press Source Button again to cancel Aux Mode
and return to previous mode.
RESET BUTTON
The RESET button is located on the main unit (as shown on the diagram). To press it vertically with a
ballpointpenormetalobjectwillactivateit. Theresetbuttonistobeactivatedforthefollowingreasons:
Initialinstallationoftheunitwhenallwiringiscompleted.
Allthefunctionbuttonsdonotoperate.
Errorsymbolonthedisplay.
Note: If the unit cannot function normally after reseting, please use a cotton swab soaked in
isopropyl alcohol to clean the socket on the back of the control panel.
E - 7
Download from Www.Somanuals.com. All Manuals Search And Download.
7. AUDIO OPERATIONS
10) VOLUME KNOB
Turn this knob to adjust desired volume level.
4) AUDIO BUTTON
Press thisbutton to select desired audio function.
ORDER OF FUNCTION:
VOLUME(VOL) -> BASS(BAS) -> TREBLE(TRE) ->BALANCE(BAL) ->FADER(FAD)
While the selected function is displayed, turn Volume Knob to adjust the level within 5 seconds,
otherwise the unit will return to volume adjustment mode.
2) MUTE BUTTON (MUTE)
Pressthisbuttontomutethesound. Pressitagaintoresumelistening.
17) PRESET EQUALIZER BUTTON (EQ)
PressthisbuttontotogglethefollowingEQsettings:
FLAT->CLASSICS->POP M->ROCK M->DSP OFF
AtDSPOFFmode, EQwillbecontrolledbyBass/Treblesetting.
13) BAND/LOUDNESS BUTTON (BAND/LOUD)
Press the Band/Loudness Button for couple of seconds to switch the loudness on or off. When
Loudness is on, display will show'Loud On' fora fewseconds.
E - 8
Download from Www.Somanuals.com. All Manuals Search And Download.
8. RADIO OPERATIONS
11) AUTO MEMORY STORE/PRESET SCAN BUTTON (AS/PS)
1.PRESET SCAN: Press AS/PS button briefly to enter Preset Scan mode, it will scan all the preset
stations in the memories, you can hear that it will stay on each station for about 5 seconds.
2.AUTO MEMORY STORE: Press AS/PS button for couple of seconds to enter Auto Store mode,
this feature will automatically scan the current band and enter up to 6 strongest stations into the
6 preset memories. To stop Auto Store & Scan, press the AS/PS button again.
7) STATION PRESET BUTTONS (M1-M6)
1.Press these buttons briefly to recall the stored stations in the selected band.
2.Presetting stations manually, Press the BAND button to select the band for the stations to be
preset. Use Tuning Up/Down to tune in the stations to be preset. Press the Preset button at
which you want to store the station for at least 2 second. The preset number will appear on the
display accompanied by a beep, this indicates that the station has been stored into memory.
13) BAND/LOUDNESS BUTTON (BAND/LOUD)
This a dual function button. Press this button shortly to change between BAND FM1, FM2, FM3 or
AM/MW bands. Press this button for couple of seconds to turn Loudness function on or off.
14) TUNING / SEEK UP AND TUNING / SEEK DOWN BUTTONS
1.Press these buttons briefly, and the unit will operate in AUTO SEARCH tuning mode, the radio
will tune up or down to the next station and remain on that station.
2.Press these buttons for more than 2 seconds, operate as MANUAL SEARCH buttons, under this
mode the tuning frequency will advance up or down rapidly when the button is pressed. If the
buttons are not pressed within 3 seconds, they will return to auto search mode.
8) MONO STEREO BUTTON (MO/ST)
When you receive a station,“ST” on the display will be on. Press this button to enter Mono mode.
9) SCAN BUTTON(SCAN)
Press this button, the radio will tune up to search stations, the available stations will blink and stay
on the display for a few seconds.
6) LOCAL/DISTANT BUTTON (LOC)
During station tuning, this button allows you prior to access strong local station only (Local
mode), or to access a wider range of using distant mode (DX). When powered on, DX mode will
be defaulted automatically; Press LOC button briefly to select Local mode and “LOCAL” symbol
on the LCD will light up for a few seconds.
E - 9
Download from Www.Somanuals.com. All Manuals Search And Download.
9.CD OPERATIONS
M1) PAUSE BUTTON (PAUSE)
Press this button to pause CD play, press again to release pause.
M2) SCAN BUTTON (SCAN)
Press this button, the first 10 seconds of each track will be played sequentially until this button
ispressedagain, thennormalplaywillresumeatthecurrenttrack.
M3) REPEAT BUTTON (REPEAT)
Press this button, the current track will be played repeatedly until this button is pressed again.
M4) SHUFFLE BUTTON (SHUFFLE)
Press this button to play all tracks on CD in random. Press again to deactivate it.
14) TRACK UP AND TRACK DOWN BUTTON
Press the Track Up Button to skip to the next track or previous track. Press the Track Down
button during play will return to the beginning of the current track, press it one more time to skip
to previous skip. Press and hold Track Up/Down Button to fast forward or fast reverse. CD
player starts playing when you release the button.
EJECT BUTTON
Press this button to eject the CD from the unit. The receiver will switch to radio mode
automatically.
EJECT BUTTON
E - 10
Download from Www.Somanuals.com. All Manuals Search And Download.
10.REMOTE CONTROL
8
9
1
2
3
10
11
12
4
5
6
7
13
14
OPERATIONS:
Key
Radio Mode
CD Player Mode
Power On/Off
(
)
Power On/Off
1. Power
Adjust Vol,Bas,
Tre,Fad,Bal
Adjust Vol,Bas,
Tre,Fad,Bal
2. Volume Up/Down
Display Clock
Display Clock
3. DISP
4.Stereo/Mono
No Function
Stereo/FM Mono
Tuning/Seek Up/Down
Local/Distant
Track Up/Down
No Function
No Function
Mute
5. Tuning Up/Down
6. LOC
Station Scan
7. Scan
Mute
8. Mute
Select Vol, Bas,
Tre, Fad, Bal
Select Vol, Bas,
Tre, Fad, Bal
9. Audio
Sub-woofer/
Change to CD or
AUX IN
Sub-woofer/
Change to Radio or AUX IN
10. Sub-woofer(SUB)/
Source
Band/Loudness
11. Band/Loud
Loudness
Auto Store/Preset Scan
Preset EQ
No function
Preset EQ
Pause
12. AS/PS
13. EQ
Preset station 1
Preset station 2
Preset station 3
Preset station 4
Preset station 5
Preset station 6
14. Numeric Key(1)
(2)
(3)
(4)
(5)
(6)
CD scan
Repeat
Shuffle
No Function
No Function
E - 11
Download from Www.Somanuals.com. All Manuals Search And Download.
11.SPECIFICATIONS
CD PLAYER
Compact disc audio system
System
Usable disc
Sampling frequency
No of quantization bits
Frequency
Compact disc
44.1KHz
1bit
5-20,000Hz
2 stereo
70dB
Number of channels
S/N Ratio
RADIO SECTION
FM
87.5-107.9MHz
10.7 MHz
Better than 15dB at S/N 30 dB
25 dB at 1KHz
50 dB
FrequencyRange
IntermediateFrequency
Usable Sensitivity
Stereo Separation
S/N Ratio
AM/MW
FrequencyRange
IntermediateFrequency
Usable Sensitivity
S/N Ratio
530-1710KHz
450KHz
Better than 45dB
40 dB
GENERAL
Power Supply
Polarity
Speaker impedance
Power Output
DC 11 -14V
Negative Ground
4 ohms
4x 50 Watts
REMARK :
Specifications subject to change without notice.
E - 12
Download from Www.Somanuals.com. All Manuals Search And Download.
12.TROUBLE SHOOTING
Before going through the check list, check wiring connection. If any of the problems persist after check
list has been made, consult your nearest service dealer.
Symptom
No power
Cause
Solution
If the power supply is properly connected
to the car accessory terminal, switch the
ignition key to “ACC”
The car ignition is not on.
The fuse is blown.
Replace the fuse.
Remove the disc in the player, then put a
new one.
Disc cannot be loaded Presence of CD disc inside
or ejected
the player.
Inserting the disc in reverse
direction.
Insert the compact disc with the label
facing upward.
Clean the disc or try to play a new one.
Compact disc is extremely
dirty or defective disc.
Cool off or until the ambient temperature
returns to normal.
Temperature inside the car is
too high.
Leave the player off for an hour or so,
then try again.
Condensation.
Adjust volume to a desired level.
Check wiring connection.
Volume is in minimum.
No sound
Wiring is not properly
connected.
The built-in microcomputer is
not operating properly due to
noise.
The operation keys do
not work
Press the RESET button.
Front panel is not properly fixed into its
place
The installation angle is
more than 30 degrees.
Adjust the installation angle to less than
30 degrees.
Sound skips.
The disc is extremely dirty or a
defective disc.
Clean the compact disc or try to play a
new one.
The antenna cable is not
connected.
The radio does not
work.
The radio station
automatic selection
does not work.
Insert the antenna cable firmly.
Select a station manually.
The signals are too weak.
Mechanism Error
Servo Error
Press the reset button if the error code
does not disappear, consult your nearest
service dealer.
ERROR 1
ERROR 2
Press the reset button if the error code
does not disappear, consult your nearest
service dealer.
If at any time in the future you should need to dispose of this product please note
that Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your Local Authority or retailer for
recycling advice.(Waste Electrical and Electronic Equipment Directive)
E - 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|