KTT-E Series
ELECTRIC TABLE TOP TILTING KETTLE
INSTALLATION – OPERATION – MAINTENANCE
BLODGETT OVEN COMPANY
44 Lakeside Avenue, Burlington, Vermont 05401 USA Telephone (800) 331-5842, (802) 860-3700 Fax: (802) 864-0183
S00063 Rev A (5/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
DESCRIPTION
PAGE
IMPORTANT NOTES FOR INSTALLATION AND OPERATION ......................................... 2
SERVICE CONNECTIONS ................................................................................................... 4
1.0 INSTALLATION INSTRUCTIONS ................................................................................. 5
2.0 INTRODUCTION ........................................................................................................... 7
3.0 OPERATION INSTRUCTIONS ...................................................................................... 8
4.0 CLEANING INSTRUCTIONS ....................................................................................... 10
5.0 TROUBLESHOOTING ................................................................................................. 11
APPENDIX A Material Safety Data Sheet ............................................................................ 12
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE CONNECTIONS
ELECTRICAL CONNECTION TO BE AS SPECIFIED ON DATA PLATE
ELECTRICAL CHARACTERISTICS
AMPS PER LINE
MODEL
KTT-6E
kW
7.5
PHASE
208V
36.0
20.8
57.6
33.3
220V
34.1
19.7
54.6
31.5
240V
31.3
18.1
50.0
28.9
380V
415V
N/A
10.4
N/A
480V
N/A
9.0
N/A
14.5
1
3
1
3
N/A
11.4
N/A
KTT-10E & KTT-12E
12.0
18.3
16.7
DIMENSIONS
MODEL
CAPACITY
6 gallons
23 litres
10 gallons
38 litres
12 gallons
45 litres
UNITS
inches
mm
inches
mm
inches
mm
A
12
305
B
14.38
365
15
381
17
C
24
610
26
660
28
711
D
33.5
851
34.88
886
E
15.25
387
F
G
H
27
686
28
711
30
762
J
4.25
108
K
12.38
314
L
10
22.25
565
4.50
114
4.62
117
4.12
105
KTT-6E
254
12.75
324
12.75
324
KTT-10E
KTT-12E
16
406
17.25
438
26.25
667
6.12
156
14.75
375
36.88
937
432
SAFETY RELIEF VALVE
4 [102]
DIMENSIONS ARE IN INCHES [MM]
F
A ID
14.50 [368]
18 [457]
2.25 [57]
10 [254]
1.25 [32]
4X WELD NUTS
5/16-18UNC
L
12.5 [318]
H
J
4
Download from Www.Somanuals.com. All Manuals Search And Download.
1.0 INSTALLATION INSTRUCTIONS
Immediately after unpacking, check for possible shipping damage. If the kettle is found to be
damaged, save the packaging materials and contact the carrier within 15 days of delivery.
1. The kettle must be installed in accordance with:
2. State and/or local codes.
3. In the USA, the National Electrical Code, ANSI/NFPA-70 (latest edition). In Canada, the
Canadian Electrical Code, Part 1, CSA Standard C22.1 (latest edition).
4. Position appliance on counter allowing sufficient rear clearance from wall to tilt freely and
completely without obstruction.
5. Mark four corner locations of appliance base.
6. Remove appliance from counter and locate position of 4 holes as per Figure 1. Drill four
7/16" diameter holes.
7. Apply a continuous bead of Silastic or other equivalent sealant along the complete perimeter
edge of the appliance base.
8. Use 5/16-18 Hex Cap Screws with suitable flat washers to bolt down. Screw length must be
1-1/4 long plus counter top thickness.
9. Wipe off excess sealant.
10. A control box with power supply equivalent to Electrical Rating of appliance should be
located conveniently nearby.
WARNING
ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE APPLICABLE
PORTIONS OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL ELECTRICAL
CODES.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
1.0 INSTALLATION INSTRUCTIONS (Continued)
1. A waterproof electrical connection for power supply to console housing must be provided.
2. Ground appliance to terminal provided inside console housing.
WARNING
DISCONNECT ELECTRICAL POWER SUPPLY AND PLACE A TAG AT THE
DISCONNECT SWITCH TO INDICATE YOU ARE ON THE CIRCUIT.
3. Turn power ON and check for proper operation.
FIGURE 1
6
Download from Www.Somanuals.com. All Manuals Search And Download.
2.0 INTRODUCTION
DESCRIPTION
Models KTT-6E (6 gallon capacity) and KTT-10E (10 gallon capacity) and KTT-12E (12 gallon
capacity) electrically powered, self-contained, countertop, tilting kettles. Each model has a
jacket of double-wall construction forming a sealed reservoir around the lower two-thirds of the
kettle. The reservoir is charged with distilled water. Kettles are equipped with a removable
electric heating element and controls, including a low water cutoff device for protection of the
heating element. All models are of identical construction, except for kettle size and element
heating capacity.
BASIC FUNCTION
Self-contained kettles operate by generating steam in the kettle reservoir. The sequence of
operation is as follows:
1. Operator turns the power switch to the ON position and sets the temperature control dial to
the desired setting from 1 to 10.
2. Control circuit is normally completed to the temperature controller if the following conditions
exist:
A. Water level in the kettle reservoir is adequate to prevent circuit interruption by the low
water cut off device. An activated cutoff is indicated by the amber low water light turning
on, and the heating element shut off.
B. Kettle is in vertical position with circuit completed through the tilt interlock switch.
3. Thermostat control contacts close to energize contactor coils.
4. Power is supplied to the elements through closed power contactors.
5. As the temperature of water rises in the kettle reservoir, increase in steam pressure is
indicated on the pressure gauge.
6. When the temperature of steam in the reservoir reaches the setting of the temperature
control dial, the temperature controller opens to break the contacts and shuts off the heating
element. On/off cycles will occur as required to maintain temperature setting.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
3.0 OPERATION INSTRUCTIONS
1. Ensure that the external electrical shut-off to the kettle is on.
2. Check pressure gauge for correct cold kettle reading. Reading should be in the green
vacuum zone. If reading is not in the vacuum zone, follow VENTING INSTRUCTION prior to
using the kettle.
3. Place power switch in ON position.
4. Preheat the kettle by placing thermostat knob at ‘10' and wait until TEMPERATURE light
goes off.
NOTE
PREHEATING SHOULD NOT BE USED WHEN COOKING MILK AND EGG FOOD
PRODUCTS WHICH ADHERE TO HOT COOKING SURFACES. THESE FOODS
SHOULD BE PLACED INTO KETTLE BEFORE HEATING IS BEGUN.
5. Add food to be cooked into the kettle.
6. Place thermostat knob at required temperature setting from 1 to 10 coinciding with a
temperature range from roughly 165EF to 289EF (74E C to 143E C, jacket temperature.)
Approximate cooking temperatures with water at various thermostat settings are as follows:
THERMOSTAT SETTING
APPROXIMATE TEMPERATURE (WATER)
FAHRENHEIT
CELSIUS
4
5
6
7
8
90E
125E
160E
195E
231E
273E
289E
32E
52E
41E
91E
110E
134E
143E
9
10
8
Download from Www.Somanuals.com. All Manuals Search And Download.
3.0 OPERATION INSTRUCTIONS (Continued)
7. When cooking is finished set thermostat knob and power switch to the OFF position.
8. Pour finished product from kettle using tilt handle. Be careful to avoid splashing.
9. Add water to kettle for cleaning purposes.
10. Wash kettle thoroughly. See CLEANING procedure.
TILTING INSTRUCTIONS
Your kettle has the standard “Clean Lock” feature and may not be tilted without disengaging the
tilt knob located on the console at the top right. This feature locks the kettle in the upright
position and also allows the operator to lock the kettle at 105 degrees for ease of cleaning. To
tilt the kettle the full distance, the tilt lock knob must be disengaged from the cleaning position
by pulling out the tilt lock knob and tilting the kettle forward the full distance. Follow these steps
to tilt kettle:
1. Pull out the tilt knob near top right of console.
2. Using kettle tilt handle pull kettle forward to desired angle of pour or until kettle locks at 105
degrees. The tilt knob can be released after the kettle has been tilted approximately 10E.
3. Kettle will lock in position at 105 degrees and may be tilted further by pulling the tilt lock
knob a second time allowing the kettle to tilt the full distance.
4. To return the kettle to the upright position, pull out the tilt lock knob and tilt the kettle upward
until it locks in the upright position. The kettle should not move in either direction once in the
upright position.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
4.0 CLEANING INSTRUCTIONS
The kettle interior and exterior should be thoroughly washed after each use in preparation of a
different food.
1. Add water and mild detergent to the kettle immediately after use.
2. Scrub kettle interior with nylon brush.
NOTE
NEVER SCRAPE THE INSIDE OF THE KETTLE WITH METAL TOOLS, STEEL
SCOURING PADS, OR ABRASIVE CLEANERS. SCRATCHES WILL RESULT
WHICH WILL SPOIL THE KETTLE’S GENERAL APPEARANCE AND MAKE IT
HARDER TO CLEAN AND MAINTAIN A SANITARY CONDITION.
3. Loosen food which is stuck to kettle by allowing it to soak at a low temperature setting.
4. Rinse with clear water and dry.
WARNING
DO NOT HOSE DOWN APPLIANCE UNDER ANY CONDITION. FAILURE TO
COMPLY WILL VOID WARRANTY.
5. Wipe down exterior, rinse and dry.
WARNING
IT IS NOT RECOMMENDED TO USE CLEANING AGENTS THAT ARE
CORROSIVE.
Use of cleaning agents that contain chloride, acids or salts are corrosive and may cause pitting
and corrosion when used over a period of time; this will reduce the life of the appliance.
Should pitting or corrosion occur this is not covered by warranty.
Follow the recommended cleaning instructions. Use a mild detergent, warm water and rinse
thoroughly.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
5.0 TROUBLESHOOTING
5.1 GENERAL MAINTENANCE
No general maintenance is required other than adhering to the Cleaning Procedure Instructions.
5.2 LOW WATER LEVEL
Proper water level must be maintained within the jacket for the kettle to operate. Depletion of
water may occur from excessive opening of, or leakage through the safety relief valve.
If water is below required operating level, either initially at start-up or during use, the kettle will
automatically shut off, and the LOW WATER signal light will come on.
In order for the kettle to operate, the following procedure must be followed:
1. Trip the safety relief valve lever to relieve all pressure from the kettle jacket.
2. At exterior rear of kettle jacket remove nut from Air Vent.
3. Insert funnel into Air Vent opening and slowly add the indicated amount of distilled water for:
KTT-6E
Add 50 oz.
(1.5 litres)
KTT-10E and KTT-12E
Add 100 oz. (3 litres)
4. Replace Air Vent nut.
5. Follow Air Venting Instructions below.
6. Continue normal Operating Procedure of kettle.
5.3 VENTING INSTRUCTION
Check pressure gauge when kettle is cold. Gauge should be in the green vacuum zone. If not,
air is present which must be vented (removed) for proper heating. Use the following procedures
to vent air.
1. With an empty kettle, place power switch to the ON position.
2. Set temperature control thermostat to ‘10'. Heat kettle until heat indicator light goes off.
3. Using a 7/16" wrench, open bleed vent one full turn for 10 seconds and then close.
4. Cool kettle. Check for proper vacuum in the green vacuum zone. If reading is not low
enough, repeat entire procedure.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX ‘A’
MATERIAL SAFETY DATA SHEET
PREPARATION INFORMATION:
Prepared for use in Canada by: E H & S Product Regulatory Management Department
DOW CHEMICAL CANADA INC.
P.O. Box 1012
Sarnia, Ontario, N7T 7K7
(800) 331-6451
1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
IN CASE OF EMERGENCY: Fort Saskatchewan, Alberta: (780) 998-8282
Sarnia, Ontario: (519) 339-3711
Varennes, Quebec: (450) 652-1000
Product::
DOWFROST* HD HEAT TRANSFER FLUID, DYED
Product Code:
Effective Date:
04632
2/20/01
Date Printed: 07/10/02
MSD: 002239
DOW CHEMICAL CANADA INC.
P.O. Box 1012
Sarnia, Ontario, N7T 7K7
Prepared for use in Canada by the E H & S Product Regulatory Management Department;
Phone: (800) 331-6451.
S
COMPOSITION/INFORMATION ON INGREDIENTS
Propylene Glycol
Dipotassium PhosphateCAS# 007758-11-4
Deionized Water CAS# 007732-18-5
CAS# 000057-55-6
94%
<5%
<5%
* or (R) indicates a trademark of The Dow Chemical Company.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
S
HAZARDS IDENTIFICATION
EMERGENCY OVERVIEW
Clear yellow liquid. Odourless. Avoid temperatures above 450EF, 232EC.
POTENTIAL HEALTH EFFECTS (See Section 11 for toxicological data.)
EYE: May cause slight transient (temporary) eye irritation. Corneal injury is unlikely. Mists
may cause eye irritation.
SKIN CONTACT: Prolonged contact is essentially nonirritating to skin. A single prolonged
exposure is not likely to result in the material being absorbed through skin in harmful amounts.
Repeated exposures may cause flaking and softening of skin.
INGESTION: Single dose oral toxicity is considered to be extremely low. No hazards
anticipated from swallowing small amounts incidental to normal handling operations.
INHALATION: At room temperature, vapours are minimal due to physical properties. Mists
may cause irritation of upper respiratory tract (nose and throat).
SYSTEMIC (OTHER TARGET ORGAN) EFFECTS: Repeated excessive exposure to
propylene glycol may cause central nervous system effects.
CANCER INFORMATION: Did not cause cancer in laboratory animals.
TERATOLOGY (BIRTH DEFECTS): Birth defects are unlikely. Exposures having no adverse
effects on the mother should have no effect on the fetus.
REPRODUCTIVE EFFECTS: In animal studies, has been shown not to interfere with
reproduction.
* or (R) indicates a trademark of The Dow Chemical Company.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
4. FIRST AID
EYES:
Flush eyes with plenty of water.
SKIN:
Wash off in flowing water or shower.
INGESTION:
No adverse effects anticipated by this route of exposure incidental
to proper industrial handling.
INHALATION:
Remove to fresh air if effects occur. Consult a physician.
NOTE TO PHYSICIAN:
No specific antidote. Supportive care. Treatment based on
judgment of the physician in response to reactions of the patient.
5. FIRE FIGHTING MEASURES
FLAMMABLE PROPERTIES
FLASH POINT:
214EF, 107EC (based on a similar material)
PMCC
METHOD USED:
AUTOIGNITION TEMPERATURE: NOT DETERMINED
FLAMMABILITY LIMITS
LFL: Not determined
UFL: Not determined
HAZARDOUS COMBUSTION PRODUCTS: During a fire, smoke may contain the original
material in addition to unidentified toxic and/or irritating compounds. Hazardous combustion
products may include and are not limited to carbon monoxide and carbon dioxide.
* or (R) indicates a trademark of The Dow Chemical Company.
OTHER FLAMMABILITY INFORMATION: Violent steam generation or eruption may occur
upon application of direct water stream to hot liquids. Flammable concentrations of vapour can
accumulate at temperatures above 214EF. Liquid mist of this product can burn. Spills of these
organic liquids on hot fibrous insulations may lead to lowering of the autoignition temperatures
possibly resulting in spontaneous combustion. Container may rupture from gas generation in a
fire situation.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
EXTINGUISHING MEDIA: Water fog or fine spray, carbon dioxide, dry chemical, foam. Alcohol
resistant foams (ATC type) are preferred if available. General purpose synthetic foams
(including AFFF) or protein foams may function, but much less effectively. Do not use direct
water stream. May spread fire.
MEDIA TO BE AVOIDED: Do not use direct water stream.
FIRE FIGHTING INSTRUCTIONS: Keep people away. Isolate fire area and deny unnecessary
entry. Burning liquids may be moved by flushing with water to protect personnel and minimize
property damage. Burning liquids may be extinguished by dilution with water. Do not use direct
water stream. May spread fire. Fight fire from protected location or safe distance. Consider
use of unmanned hose holder or monitor nozzles. Use water spray to cool fire exposed
containers and fire affected zone until fire is out and danger of re-ignition has passed.
Immediately withdraw all personnel from area in case of rising sound from venting safety device
or discolouration of the container. Move container from fire area if this is possible without
hazard.
PROTECTIVE EQUIPMENT FOR FIRE FIGHTERS: Wear positive-pressure self-contained
breathing apparatus (SCBA) and protective fire fighting clothing (includes fire fighting helmet,
coat, pants, boots and gloves). If protective equipment is not available or not used, fight fire
from a protected location or safe distance.
6. ACCIDENTAL RELEASE MEASURES (See Section 15 for Regulatory Information)
PROTECT PEOPLE: Use appropriate safety equipment. For additional information, refer to
Section 8, Exposure Controls/ Personal Protection.
PROTECT THE ENVIRONMENT: Avoid contamination of all waterways.
CLEAN-UP: See Section 13, Disposal Consideration.
* or (R) indicates a trademark of The Dow Chemical Company.
S
HANDLING AND STORAGE
SPECIAL PRECAUTIONS TO BE TAKEN IN HANDLING AND STORAGE: No special handling
requirements data available.
HANDLING: See Section 8, Exposure Controls/Personal Protection.
STORAGE: See Section 10, Stability and Reactivity.
S
EXPOSURE CONTROLS/PERSONAL PROTECTION
ENGINEERING CONTROLS: Provide general and/or local exhaust ventilation to control
15
Download from Www.Somanuals.com. All Manuals Search And Download.
airborne levels below the exposure guidelines.
PERSONAL PROTECTIVE EQUIPMENT
EYE/FACE PROTECTION: Use safety glasses. Safety glasses should be sufficient for most
operations; however, for misty operations wear chemical goggles.
SKIN PROTECTION: Use gloves impervious to this material.
RESPIRATORY PROTECTION: Atmospheric levels should be maintained below the exposure
guideline. When respiratory protection is required for certain operations, use an approved air-
purifying respirator. In misty atmospheres, use an approved mist respirator.
EXPOSURE GUIDELINES: Propylene glycol: AIHA WEEL is 50 ppm total, 10 mg/m3 aerosol
only.
9. PHYSICAL AND CHEMICAL PROPERTIES
APPEARANCE/PHYSICAL STATE:
ODOUR:
Clear yellow liquid.
Odourless
VAPOR PRESSURE:
VAPOR DENSITY:
BOILING POINT:
0.22 mmHg @ 20EC
2.6
320EF, 160EC
SOLUBILITY IN WATER/MISCIBILITY: Complete
SPECIFIC GRAVITY OR DENSITY:
1.058 @ 25/25EC
* or (R) indicates a trademark of The Dow Chemical Company.
10. STABILITY AND REACTIVITY
CHEMICAL STABILITY: Thermally stable at typical use temperatures.
CONDITIONS TO AVOID: Avoid use temperatures above 450EF, 232EC. Product can degrade
at elevated temperatures. Generation of gas during decomposition can cause pressure in
closed systems.
INCOMPATIBILITY WITH OTHER MATERIALS: Avoid contact with oxidizing materials. Avoid
contact with strong acids
HAZARDOUS DECOMPOSITION PRODUCTS: Hazardous decomposition products depend
upon temperature, air supply and the presence of other materials.
HAZARDOUS POLYMERIZATION: Will not occur.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
11. TOXICOLOGICAL INFORMATION (See Section 3 for Potential Health Effects. For
detailed toxicological data, write or call the address or non-emergency number shown in
Section 1).
SKIN: The LD50 for skin absorption in rabbits is >10,000 mg/kg.
SKIN:
The LD50 for skin absorption in rabbits is >10,000 mg/kg.
The oral LD50 for rats is 20,000 - 34,000 mg/kg.
INGESTION:
MUTAGENICITY:
In vitro mutagenicity studies were negative. Animal mutagenicity studies
were negative.
S
ECOLOGICAL INFORMATION (For detailed Ecological data, write or call the address or
non-emergency number shown in Section 1.)
ENVIRONMENTAL FATE
MOVEMENT & PARTITIONING: Based largely or completely on data for major component(s).
Bioconcentration potential is low (BCF less than 100 or Log Pow less than 3). Potential for
mobility in soil is very high (Koc between 0 and 50).
* or (R) indicates a trademark of The Dow Chemical Company.
DEGRADATION AND PERSISTENCE: Based largely or completely on data for major
component(s). Material is readily biodegradable. Passes OECD test(s) for ready
biodegradability. Degradation is expected in the atmospheric environment within minutes to
hours.
ECOTOXICITY: Based largely or completely on data for major component(s). Material is
practically non-toxic to aquatic organisms on an acute basis (LC50/EC50 >100 mg/L in most
sensitive species).
S
DISPOSAL CONSIDERATIONS (See Section 15 for Regulatory Information)
DISPOSAL: DO NOT DUMP INTO ANY SEWERS, ON THE GROUND OR INTO ANY BODY
OF WATER. All disposal methods must be in compliance with all Federal, State/Provincial and
local laws and regulations. Regulations may vary in different locations. Waste
characterizations and compliance with applicable laws are the responsibility solely of the waste
generator. THE DOW CHEMICAL COMPANY HAS NO CONTROL OVER THE
MANAGEMENT PRACTICES OR MANUFACTURING PROCESSES OF PARTIES HANDLING
OR USING THIS MATERIAL. THE INFORMATION PRESENTED HERE PERTAINS ONLY TO
THE PRODUCT AS SHIPPED IN ITS INTENDED CONDITION AS DESCRIBED IN MSDS
SECTION 2 (Composition/Information On Ingredients).
17
Download from Www.Somanuals.com. All Manuals Search And Download.
FOR UNUSED & UNCONTAMINATED PRODUCT, the preferred options include sending to a
licensed, permitted: recycler, reclaimer, incinerator or other thermal destruction device.
As a service to its customers, Dow can provide names of information resources to help identify
waste management companies and other facilities which recycle, reprocess or manage
chemicals or plastics, and that manage used drums. Telephone Dow’s Customer Information
Center at 800-258-2436 or 989-832-1556 for further details.
14. TRANSPORT INFORMATION
DEPARTMENT OF TRANSPORTATION (D.O.T.): For D.O.T. regulatory information, if
required, consult transportation regulations, product shipping papers, or contact your Dow
representative.
CANADIAN TDG INFORMATION: For TDG regulatory information, if required, consult
transportation regulations, product shipping papers, or your Dow representative.
* or (R) indicates a trademark of The Dow Chemical Company.
15. REGULATORY INFORMATION (Not meant to be all-inclusive – selected regulations
represented).
NOTICE: The information herein is presented in good faith and believed to be accurate as of
the effective date shown above. However, no warranty, express or implied is given. Regulatory
requirements are subject to change and may differ from one location to another; it is the buyer’s
responsibility to ensure that its activities comply with federal, state or provincial, and local laws.
The following specific information is made for the purpose of complying with numerous federal,
state or provincial, and local laws and regulations. See other sections for health and safety
information.
* or (R) indicates a trademark of The Dow Chemical Company.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
U.S. REGULATIONS
SARA 313 INFORMATION: To the best of our knowledge, this product contains no chemical
subject to SARA Title III Section 313 supplier notification requirements.
SARA HAZARD CATEGORY: This product has been reviewed according to the EPA “Hazard
Categories” promulgated under Sections 311 and 312 of the Superfund Amendment and
Reauthorization Act of 1986 (SARA Title III) and is considered, under applicable definitions, to
meet the following categories:
Not to have met any hazard category.
TOXIC SUBSTANCES CONTROL ACT (TSCA):
All ingredients are on the TSCA inventory or are not required to be listed on the TSCA
inventory.
STATE RIGHT-TO-KNOW: The following product components are cited on certain state lists as
mentioned. Non-listed components may be shown in the composition section of the MSDS.
CHEMICAL NAME
1, 2-Propanediol
CAS NUMBER
000057-55-6
LIST
PA1
PA1= Pennsylvania Hazardous Substance (present at greater than or equal to 1.0%).
OSHA HAZARD COMMUNICATION STANDARD:
This product is not a “Hazardous Chemical” as defined by the OSHA Hazard Communication
Standard, 29 CFR 1910.1200.
* or (R) indicates a trademark of The Dow Chemical Company.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
CANADIAN REGULATIONS
WHMIS INFORMATION: The Canadian Workplace Hazardous Materials Information System
(WHMIS) Classification for this product is:
This product is not a “Controlled Product” under WHMIS.
CANADIAN ENVIRONMENTAL PROTECTION ACT (CEPA)
This product contains one or more substances which are not listed on the Canadian Domestic
Substances List (DSL). Contact your Dow representative for more information.
16. OTHER INFORMATION
MSDS STATUS: Revised to 16 section format.
The information herein is given in good faith, but no warranty, express or implied, is made.
Consult The Dow Chemical Company for further information.
* or (R) indicates a trademark of The Dow Chemical Company.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
|