VSC-VPLEX4
VideoPlex4 Video Wall Controller
Display standard single- or dual-link DVI input
across four output monitors.
Each output can be driven as DVI or analog RGB, and can represent
an arbitrary crop region of the original input image.
Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500)
Customer
Support
Information
FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746
Mailing address: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC and IC RFI Statements
Federal Communications Commission and Industry Canada Radio Frequency Interference
Statements
This equipment generates, uses, and can radiate radio-frequency energy, and if not installed and used properly, that is, in strict
accordance with the manufacturer’s instructions, may cause interference to radio communication. It has been tested and found to
comply with the limits for a Class A computing device in accordance with the specifications in Subpart B of Part 15 of FCC rules,
which are designed to provide reasonable protection against such interference when the equipment is operated in a commercial
environment. Operation of this equipment in a residential area is likely to cause interference, in which case the user at his own
expense will be required to take whatever measures may be necessary to correct the interference.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
This digital apparatus does not exceed the Class A limits for radio noise emission from digital apparatus set out in the Radio
Interference Regulation of Industry Canada.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques
de la classe A prescrites dans le Règlement sur le brouillage radioélectrique publié par Industrie Canada.
724-746-5500 | blackbox.com
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
NOM Statement
Instrucciones de Seguridad
(Normas Oficiales Mexicanas Electrical Safety Statement)
1. Todas las instrucciones de seguridad y operación deberán ser leídas antes de que el aparato eléctrico sea operado.
2. Las instrucciones de seguridad y operación deberán ser guardadas para referencia futura.
3. Todas las advertencias en el aparato eléctrico y en sus instrucciones de operación deben ser respetadas.
4. Todas las instrucciones de operación y uso deben ser seguidas.
5. El aparato eléctrico no deberá ser usado cerca del agua—por ejemplo, cerca de la tina de baño, lavabo, sótano mojado o cerca
de una alberca, etc.
6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales que sean recomendados por el fabricante.
7. El aparato eléctrico debe ser montado a la pared o al techo sólo como sea recomendado por el fabricante.
8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más allá a lo descrito en las instrucciones de operación.
Todo otro servicio deberá ser referido a personal de servicio calificado.
9. El aparato eléctrico debe ser situado de tal manera que su posición no interfiera su uso. La colocación del aparato eléctrico
sobre una cama, sofá, alfombra o superficie similar puede bloquea la ventilación, no se debe colocar en libreros o gabinetes
que impidan el flujo de aire por los orificios de ventilación.
10. El equipo eléctrico deber ser situado fuera del alcance de fuentes de calor como radiadores, registros de calor, estufas u otros
aparatos (incluyendo amplificadores) que producen calor.
11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo del tipo descrito en el instructivo de operación, o como
se indique en el aparato.
12. Precaución debe ser tomada de tal manera que la tierra fisica y la polarización del equipo no sea eliminada.
13. Los cables de la fuente de poder deben ser guiados de tal manera que no sean pisados ni pellizcados por objetos colocados
sobre o contra ellos, poniendo particular atención a los contactos y receptáculos donde salen del aparato.
14. El equipo eléctrico debe ser limpiado únicamente de acuerdo a las recomendaciones del fabricante.
15. En caso de existir, una antena externa deberá ser localizada lejos de las lineas de energia.
16. El cable de corriente deberá ser desconectado del cuando el equipo no sea usado por un largo periodo de tiempo.
17. Cuidado debe ser tomado de tal manera que objectos liquidos no sean derramados sobre la cubierta u orificios de ventilación.
18. Servicio por personal calificado deberá ser provisto cuando:
A: El cable de poder o el contacto ha sido dañado; u
B: Objectos han caído o líquido ha sido derramado dentro del aparato; o
C: El aparato ha sido expuesto a la lluvia; o
D: El aparato parece no operar normalmente o muestra un cambio en su desempeño; o
E: El aparato ha sido tirado o su cubierta ha sido dañada.
724-746-5500 | blackbox.com
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions
Safety Instructions
To prevent damage to your VideoPlex4 or injury to personnel operating the equipment, read the following safety precautions prior
to operation. These instructions should be made available to all those who will use and operate the VideoPlex4.
Power Supply
All VideoPlex4s require a power supply. This power supply must be disconnected when equipment is being upgraded or
relocated.
Cables
Do not expose cables to any liquids; doing so may cause a short circuit that could damage the equipment. Do not place heavy
objects on top of any cables, because this can cause damage and possibly lead to exposed live wires.
Ventilation
All computer equipment should be located in a well-ventilated area. All ventilation holes on the unit casing must be kept clear of
any obstruction at all times. Failure to do so will result in the system overheating and damaging your equipment.
Working Environment
Locate the equipment in an environment free from dust, moisture, and extreme changes in temperature. Place the VideoPlex4 on
a stable and solid work surface. Do not place liquids (hot/cold drinks, etc.) near the equipment because spills could cause serious
damage.
Gas/Flammable Liquids
Never use electronic equipment in the presence of gas or any flammable liquid; doing so could result in an explosion or serious
fire.
Smoke/Unusual Smells
If you notice smoke or unusual smells being emitted from your computer, turn off and unplug the system from the power supply.
Then pass the system to a qualified technician for inspection. Continued operation could result in personal injury and damage to
property.
Maintenance
Maintenance should only be carried out by competent technicians. Any VideoPlex4s that are damaged should be returned to
Black Box for repair using Black Box RMA procedures.
Disposal
At the end of life, all VideoPlex4s should be disposed of as local laws and regulations dictate.
724-746-5500 | blackbox.com
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Table of Contents
1. Specifications...............................................................................................................................................................7
2. Overview ..................................................................................................................................................................8
2.1 Introduction.........................................................................................................................................................8
2.2 Configuration Examples ......................................................................................................................................8
2.3 What’s Included ................................................................................................................................................ 12
2.4 Hardware Description........................................................................................................................................ 13
2.4.1 Front Panel.............................................................................................................................................. 13
2.4.2 Back Panel............................................................................................................................................... 14
3. Setting Up the VideoPlex4......................................................................................................................................... 15
4. Configuring the VideoPlex4....................................................................................................................................... 16
4.1 Factory Default Settings..................................................................................................................................... 16
4.2 Configuring DVI Input Resolution...................................................................................................................... 16
4.3 Monitor Outputs ............................................................................................................................................... 16
4.4 Selecting the Regions to be Displayed............................................................................................................... 16
5. Operating Instructions ............................................................................................................................................... 18
5.1 DVI Input........................................................................................................................................................... 18
5.2 Output............................................................................................................................................................... 18
5.3 Configuring the VideoPlex4............................................................................................................................... 18
5.4 Frame-Lock........................................................................................................................................................ 18
6. VideoPlex4 Control Application ................................................................................................................................. 19
6.1 Application Installation...................................................................................................................................... 19
6.2 Running the VideoPlex4 Control Application..................................................................................................... 19
6.3 Connection Diagram .........................................................................................................................................20
6.4 Device................................................................................................................................................................20
6.5 DVI-D Input.......................................................................................................................................................20
6.6 Input Capture Regions.......................................................................................................................................23
6.7 Predefined Regions............................................................................................................................................ 24
6.8 Monitor Outputs ............................................................................................................................................... 24
724-746-5500 | blackbox.com
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Specifications
1. Specifications
Technical Specifications
Approvals
FCC, TUV, CE, UL®, CSA, RoHS, WEEE
Arbitrary
Upscaling
Up to 64 X non-integer scale factors allowed
Cooling
This unit contains a cooling fan.
CAUTION: The input and output vents should not be restricted.
Dual-Link DVI
Capture
Up to 330 Mpixels/s
Efficiency Level
IV
Heat Dissipation (Voltage x Nominal Current) x 3.41 = BTU/hr.
Input Surface 4K x 4K maximum
Leads Supported DVI-D (Dual-Link on input only)
Operating
All known operating systems;
System Support
All known hardware that supports/follows the DVI spec
Resolution
Up to 2.5 Mpixels/s
USB Support
USB 2.0, full-speed (12 Mbps) operation;
Firmware support: Updates supported via USB
Interface
(1) Dual-link DVI capture;
(4) Single-link DVI
Connectors
Input: (1) DVI-D female;
Output: (4) DVI-I female;
Power: (1) 3-pin power female;
(1) USB Type B female;
(2) Sync ports (unused)
Indicators
(3) LEDs:
(1) Power,
(1) Input,
(1) Status
Environmental
Temperature Tolerance:
Operating: 32 to 96° F (0 to 35° C);
Humidity:
Operating: 90%, noncondensing;
Altitude (Maximum): NEED SPEC ft. (m)
Power
Input Voltage/Volts: 100–240 VAC;
Input Current/Amps: 0.8 A;
Output Voltage/Volts: 5 VDC;
Power Consumption/Watts: 18 W;
Power Supply Cord Length: 3 ft. (0.9 m)
Dimensions
1.75" H x 9.25" W x 6.9" D (4.4 x 23.5 x 17.5 cm)
724-746-5500 | blackbox.com
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Overview
2. Overview
2.1 Introduction
The VideoPlex4 is a standalone display wall controller that accepts a standard single- or dual-link DVI input and can flexibly display
this across four output monitors.
Each output can be driven as DVI or analog RGB, and can represent an arbitrary crop region of the original input image. The
output resolution and frame rate do not need to be related to that of the input, because the VideoPlex4 will optionally upscale
and frame-rate convert each cropped region independently. However, if the VideoPlex4 detects that frame rates identically match,
it will automatically frame-lock all outputs and, if possible, frame-lock these to the input signal. Additionally, each output can be
independently mirrored or rotated through 90°, 180°, or 270° to support creative mixes of landscape and portrait monitors.
2.2 Configuration Examples
On the next few pages are just a few examples of what can be achieved with the VideoPlex4. The examples are not definitive and
users are encouraged to experiment with different display configurations.
Figure 2-1. Duplicate the input signal x 4 and display each duplicate on separate screens.
724-746-5500 | blackbox.com
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Overview
Figure 2-2. Divide the input signal into quadrants and display each quarter on separate displays with optional frame rate
conversion (in this case 30 to 60 Hz). You can adjust crop regions to compensate for monitor bezel.
724-746-5500 | blackbox.com
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Overview
Figure 2-3. Duplicate the input signal x2 and display one output on a single landscape display and divide the second output into
thirds, rotate to portrait, upscale, and split between three displays.
Figure 2-4. Crop input signal, upscale specific areas, and display on four separate screens.
724-746-5500 | blackbox.com
Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Overview
Figure 2-5. Crop the input signal into VideoPlex4 and display x2 quarters landscape and x2 quarters portrait.
724-746-5500 | blackbox.com
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Overview
Figure 2-6. Crop the input signal, rotate through 90º, 180º, or 270º; display in landscape and portrait. Arbitrary crop regions can
allow the monitors to be artistically arranged, but maintain an undistorted image.
2.3 What’s Included
Your package should contain the following items. If anything is missing or damaged, contact Black Box Technical Support at
724-746-5500 or [email protected].
• VideoPlex4 Video Wall Controller
• 100–240-VAC, 5-VDC, 18-W universal power adapter
• USB 2.0 cable Type A to Type B
• VideoPlex4 CD containing configuration application and this user manual
NOTE: We recommend that you do not discard the packing box until you are completely satisfied with the VideoPlex4 and it is
fully installed and working correctly. We also recommend that you note the serial number of the controller in a prominent
place before you connect it to the computer. You will be asked to provide this serial number if you need to contact our
Technical Support department. The serial number is displayed on the VideoPlex4 and the box label.
724-746-5500 | blackbox.com
Page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Overview
Fitting the VideoPlex4 PSU Blades
Push to release blade
Figure 2-7. PSU blades.
Select the appropriate blade for use, place the top edge of the blade into the recess of the PSU and then slide upwards ensuring
the release catch clicks firmly into place and secures the blade inside the recess.
To remove the blade, press the release catch down fully and pull the blade away from the PSU recess. The PSU is shipped fitted
with the UK blade.
2.4 Hardware Description
2.4.1 Front Panel
1
2
3
Figure 2-8. Front panel.
Table 2-1. Front-panel components.
Number Indicator
Description
(1) Power LED Lights when the VideoPlex4 is connected to the power supply.
(1) Input LED Lights when a valid DVI source is connected.
1
2
3
(1) Status LED Lights steady on when the VideoPlex4 is operating normally.
Flashing when the unit is operating over the normal operating temperature. Make sure that the input fan vent is
not blocked.
Off when the settings configured in the VideoPlex4 application no longer match the input. This is normally the
result of a change of input. The VideoPlex4 will compensate for the settings and reconfigure itself to display as
near to the settings as possible. The output will still be displayed, but not necessarily as expected.
724-746-5500 | blackbox.com
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Overview
NOTE: When the VideoPlex4 is connected to a PC by a USB cable and the VideoPlex4 control application is active, all three lights
flash to identify which unit is being controlled.
2.4.2 Back Panel
1
4
4
1
2
4
3
4
5
Figure 2-9. Rear panel.
Table 2-2. Back-panel components.
Number Indicator
Description
1
2
Sync Sockets The Sync sockets are provided for future genlock enhancements. Leave them unconnected.
USB Socket
The USB socket is used to connect the VideoPlex4 to a PC via a USB connection using the supplied USB Type A to
Type B cable. Configuration of the VideoPlex4 is programmable via an application utility, allowing easy control of
cropping, scaling, rotation, and gaps.
3
DVI-D Input
Socket
The DVI-D Input socket is used to connect the DVI input source to the VideoPlex4. The VideoPlex4 supports
dual-link DVI, single-link DVI, and also HDMI (not HDCP compliant) via the optional DVI/HDMI adapter (part
number FA790).
4
5
DVI-I Output The four DVI-I Out sockets are used to connect the VideoPlex4 to the output monitors. The VideoPlex4 supports
Socket
both DVI and analog RGB monitors.
Power
The Power socket is where the supplied power source connects to the VideoPlex4. The power LED on the front of
the VideoPlex4 illuminates when a power supply is connected.
724-746-5500 | blackbox.com
Page 14
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Setting Up the VideoPlex4
3. Setting Up the VideoPlex4
• Make sure the power supply for the DVI source is disconnected.
• Connect the cable from the DVI source to the input socket on the rear of the VideoPlex4.
• Connect the four displays to the output sockets on the rear panel of the VideoPlex4.
• Connect the VideoPlex4 power supply to the VideoPlex4 and switch on the power supply at the socket.
• Power up the DVI source.
The Power LED located on the front panel will light to indicate that power has successfully been applied to the unit.
The VideoPlex4 incorporates an internal processor that will continuously monitor the received DVI signal, and whenever a valid
and stable input is detected, the Input LED is illuminated.
If the Input LED is not lit, the VideoPlex4 cannot detect a valid DVI input source.
During operation, the VideoPlex4 adjusts its internal operation to maintain the programmed output proportions even when the
input resolution changes.
VideoPlex4
(VSC-VPLEX4)
Input source
Output displayed
across all four screens
Figure 3-1. Typical setup.
724-746-5500 | blackbox.com
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Configuring the VideoPlex4
4. Configuring the VideoPlex4
4.1 Factory Default Settings
The VideoPlex4 stores a number of parameters to configure its operation. This allows it to operate standalone in a very flexible
manner. The configurations affect the input and output display modes as well as the required partitioning of the input image
between monitors.
By default the VideoPlex4 is configured as follows:
• Input EDID Preferred Mode: 1920 x 1080 x 60Hz (SMPTE timings)
• Output monitor mode: Use Monitor Preferred Mode; Default: 1920 x 1080 x 60Hz (SMPTE)
• Cropping Mode: 2x2 equal split (960x540); No Rotation
The default settings are changed using the Windows® application provided. It runs on any Windows® platform and connects to
the VideoPlex4 via the supplied USB cable. How to use the application is explained in Chapter 6.
The sections below describe the settings that are possible and why they may be needed. For details on how to program the
VideoPlex4 hardware with your desired configurations, please see Chapter 6, VideoPlex4 Control Application.
4.2 Configuring DVI Input Resolution
Because the timings and resolution of the DVI input are set by the DVI source machine, the VideoPlex4 can only configure this
indirectly by presenting a programmable “Preferred Mode” as part of its EDID (Extended Display Identification Data).
Most graphics cards and HDMI appliances automatically select the “Preferred Mode” resolution and timings presented by the
VideoPlex4 EDID, but they may need to be forced to re-detect if the EDID contents are changed by the VideoPlex4 application.
This would typically be via a hot-plug event caused by disconnecting and reconnecting the DVI input cable.
The configuration application will allow read back of the resolution that is currently being detected, as well as the ability to read
and write the internal EDID ROM.
4.3 Monitor Outputs
The VideoPlex4 can be configured to read the corresponding EDID of each monitor that is connected and to drive out a signal
that corresponds to the resolution, timings, and mode (RGB or DVI) of the Preferred Mode. This is the factory default
configuration.
NOTE: When different monitors are attached to the four outputs, each may advertise a different Preferred Mode, so each output
will be driven at a different mode.
Whenever the monitor EDID is used, the VideoPlex4 will calculate the internal scale factors to ensure that the monitor (at
whatever resolution it is being driven) will still display the correct proportion of the input image.
If an EDID cannot be read (for example, if the monitor cable does not support the DDC signals required), a default mode can be
programmed into the VideoPlex4’s memory. This is factory configured to 1080p.
In some cases, the user may require a very specific output timing (for example, when frame-locking to the input) regardless of the
monitor EDIDs. In this case, the VideoPlex4 can be configured to always output the mode that has been programmed as the
default mode.
4.4 Selecting the Regions to Be Displayed
Each output of the VideoPlex4 can take its display data from any arbitrary rectangular region of the captured input image. The
factory default for these cropping rectangles configures the four monitors to display a quarter of the input as a 2x2 array, and
these proportions are maintained across different input resolutions.
For a 1080p input, 960 x 540 pixels from the input image would be scaled up by a factor of two inches in each direction if the
selected output resolution was 1080p.
724-746-5500 | blackbox.com
Page 16
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Configuring the VideoPlex4
But, if the input resolution changes to 1600 x 1200, then for the same output monitor, the VideoPlex4 would upscale from an
800 x 600 region and would reprogram its scale factors to 2.4 horizontally and 1.8 vertically to support the same 1080p monitor.
The cropping regions can be assigned arbitrarily and can overlap; the only restriction is that the resulting scale factor must be
greater than 1.0 (i.e., 1:1 or scaled up) in either direction. For example, you can use the VideoPlex4 to output four identical copies
of the input signal (the resulting output timings must remain within the capabilities of the single-link DVI outputs).
The regions of the input image to be displayed on a given output monitor can be programmed via USB by using the VideoPlex
configuration application.
To support portrait orientation of monitors, the source data can be rotated by 90º, 180º, or 270º as it is output to the monitor.
724-746-5500 | blackbox.com
Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Operating Instructions
5. Operating Instructions
5.1 DVI Input
When the VideoPlex4 is powered up successfully and the Power, Input, and Status LED indicators are lit, a DVI input mode has
been detected and is working normally.
If the Input LED indicator is not on, make sure a single- or dual-link DVI cable is correctly fitted to the appropriate sockets.
At high resolution, DVI signals cannot normally be guaranteed beyond 16 feet (5 m) cables because of the nature of the signal
losses inherent in the DVI cables and connectors. Equalization hardware on the VideoPlex4 compensates for these losses and
supports cable lengths of up to 64 feet (20 m) even at full dual-link resolutions (330 MHz pixel clocks). Lower resolutions will
allow even longer cable lengths.
Once the LED indicators are lit, the VideoPlex4 will display the source across all four screens according to the configuration that is
stored in its non-volatile memory. The VideoPlex4 is factory configured to display the input image as a 2x2 split as shown in
Figure 3-1.
5.2 Output
To connect to an analog output, DVI-I-VGA cables are required. To connect to a DVI output, a DVI-D cable is required.
5.3 Configuring the VideoPlex4
The VideoPlex4 has a USB port to allow a host PC to connect to the VideoPlex4 box and for the user to program its
configuration. Once configured, the VideoPlex4 will run standalone without needing a USB connection and will auto-detect input
resolutions and adjust internal scaling to drive the output monitors consistently.
5.4 Frame-lock
The firmware running on the VideoPlex4 will detect when input and/or output timings are set to identical frame rates and will
automatically frame-lock the syncs in these cases. In all frame-lock modes, the timings are configured to share a common
reference clock, so there will be no drift in synchronization, and therefore no requirement for continual adjustment that can
sometimes upset LCD panels. The frame-lock status is shown in the VideoPlex4 Control Application.
724-746-5500 | blackbox.com
Page 18
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: VideoPlex4 Control Application
6. VideoPlex4 Control Application
6.1 Application Installation
NOTE: Do not plug the VideoPlex4 into a USB port until the driver installation is complete.
Locate the Install folder on the CD supplied with the VideoPlex4, run install.exe, and follow the installation wizard. During
installation, a warning message is displayed stating that the driver does not have Windows® Logo accreditation.
Select “Continue Anyway” to complete the installation.
The VideoPlex4 can now be connected to a suitable USB 1.0 or 2.0 port using the cable supplied. At this point the hardware will
be detected by Windows as a USB API, and a New Hardware wizard is displayed. Allow the wizard to search, and click on the
recommended option to enable the previously installed driver to be associated with the new hardware.
Press “Continue Anyway” to accept the driver.
6.2 Running the VideoPlex4 Control Application
To open the VideoPlex4 Control application select Start/All Programs/VideoPlex4.
The application will search for any VideoPlex4 connected to your computer and display the status of the first VideoPlex4 detected.
If there is more than one VideoPlex4 in use, a list of all available VideoPlex4s can be found in the File menu.
Once the application has detected a VideoPlex4, the main status screen is displayed as shown in Figure 6-1.
Figure 6-1. Main status screen.
724-746-5500 | blackbox.com
Page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: VideoPlex4 Control Application
The main control dialog is divided into the following groups:
• Connection Diagram
• DVI-D Input
• Input Capture Regions
• Device
• Monitor Outputs
6.3 Connection Diagram
The connection diagram displays a schematic view of the rear panel of the VideoPlex4 to assist in identifying the connectors.
Figure 6-2. Back of unit.
6.4 Device
The unique USB device name that is connected is displayed in the Device group. You can associate a more user-friendly name
such as “First Four Outputs.” The friendly name is stored in non-volatile storage on the VideoPlex4 and can to help identify the
device during future configurations. Specific devices connected to your PC can be selected using the ”Select Device” command
on the File Menu. The VideoPlex4s will be listed by the USB device or by a previously configured friendly name.
6.5 DVI-D Input
The DVI-D Input group displays the current DVI mode that is being captured (if any) and the preferred mode that has been
programmed into the VideoPlex4’s EDID. Use the Modify button to update the EDID. The small square to the left of the current
input resolution indicates whether the VideoPlex4 has frame-locked to the input source.
• Green – The outputs are frame-locked to the input dot clock and vertical sync.
• Grey – The outputs are not frame-locked.
Figure 6-3. DVI-D input screen.
724-746-5500 | blackbox.com
Page 20
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: VideoPlex4 Control Application
To boost the equalization hardware, click on the “Settings” button. The following dialog is displayed.
Figure 6-4. DVI-D input settings dialog box.
Use the slider to compensate for the loss of signal quality due to DVI cable lengths over 16 feet (5 m). The equalization hardware
can compensate for cables up to 64 feet (20 m) in length.
To change the timings of the input EDID, click on the “Modify” button. The dialog shown on the next page is displayed.
724-746-5500 | blackbox.com
Page 21
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: VideoPlex4 Control Application
Figure 6-5. DVI-D input dialog box.
The DVI-D Input dialog displays the resolution of the current mode for reference and allows the timings of the EDID preferred
mode to be edited. To populate the EDID timings with the current timings, click on the Copy Timings button.
The dialog supports standard timing formulas such as:
• VESA CVT
• VESA CVT Reduced Blanking
• SMPTE (for HD modes)
• VESA GTF
• Custom
Selecting “Auto” from the drop-down list will typically default to the VESA CVT algorithm that best matches typical standard
VESA output modes. However, to minimize dot clocks and hence maximize DVI cable lengths, we recommend using the CVT
Reduced Blanking.
Selecting “Custom” allows the timing parameters to be edited.
NOTE: You will need to select between definition of Pixel Clock or Vertical Refresh, since these are mutually exclusive parameters.
Once edited, clicking “OK” writes the preferred mode into the EDID but may not normally affect the input mode that is being
captured. You might need to force the graphics device in the host machine to detect the new modes. Just select “Detect” on the
Screen Resolutions dialog box (Windows 7) or disconnect the source from the VideoPlex4 and reconnect.
All modifications to the Input settings can be saved as part of a .vqs file, removing the requirement to input the same settings
again. To save the settings, select the “Save” command in the File menu. To open a saved .vqs file, select the “Open” command.
724-746-5500 | blackbox.com
Page 22
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: VideoPlex4 Control Application
6.6 Input Capture Regions
Each output of the VideoPlex4 can select a different region of the input source image. This dialog (Figure 6-6) displays the
settings of each region (region 1 corresponds to output 1, etc). The numbers denote the top, left, width, and height coordinates
of the region that is to be displayed.
NOTE: These are described in terms of the current active input resolution. If the input resolution changes, the capture region
coordinates scale to the new input resolution in order to maintain the same proportions.
Figure 6-6. Input capture regions screen.
To modify any of these settings, click on Modify to display the edit dialog (Figure 6-7).
Figure 6-7. Input capture regions edit dialog box.
724-746-5500 | blackbox.com
Page 23
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: VideoPlex4 Control Application
6.7 Predefined Regions
You can use the preset buttons to select the two most popular configurations: Quarter or Replicate.
Quarter
The first monitor displays the top left-hand corner of the input image, the second monitor the top right, the third the bottom left,
etc. Use this mode of operation to drive four monitors in a 2 x 2 arrangement from a single high-resolution input.
Replicate
Each output displays the entire input image. The output monitors can be driven at the same resolution (with different timings if
necessary) or a higher resolution.
There are no restrictions (other than the resulting scale factor must be 1:1 or upscale) in the region settings, so it is possible to
have regions overlapping, or to program in gaps, etc. Additionally, each region can have a transformation such as rotation or
flipping applied to it (after cropping) in order to support different output monitor orientations.
NOTE: A setting is valid when it is stored if the scale factors from input to output are 1:1 or greater. There may be instances
where a setting stored in non-volatile memory that was valid when it was stored may subsequently require down-scaling if
the resolution of the input increases. In this case, the firmware will adjust the scaling factors to give a 1:1 crop of the input,
centered on the original region. To indicate that at least one output is no longer exactly honoring the programmed region
setting, the front panel status light will not be lit.
Scaling Optimization
Scaling Optimization is used to optimize displays that have been scaled. If the display is mostly text-based, select “Text.” This will
ensure that the displayed text remains sharp after scaling. If the display is video-based, select “Video.” Scaling optimization will
ensure a smooth, un-pixellated display of video.
All modifications to the Region settings can be saved as part of a .vqs file, removing the requirement to input the same settings
again. To save the settings, select the “Save” command in the File menu. To open a saved .vqs file, select the “Open” command.
6.8 Monitor Outputs
The Monitor Outputs group shows the actual resolution and refresh rate that each of the four VideoPlex4 outputs is currently
providing. To see more information, such as whether this is an analog RGB or DVI mode, if it is the monitor EDID preferred mode,
or a default mode programmed into the VideoPlex4, along with detailed timing information, click on the “Modify” button for the
required output.
The frame-lock status is indicated by the small colored squares.
Green
The outputs are frame-locked to the Vsync of the first monitor, using a common reference clock. If the Input frame-lock light is
green, then the reference clock is taken from the input DVI source, and the system is fully frame-locked to this source. If the input
frame-locked indicator is gray, then the outputs are frame-locked together, but are not related to the input sync.
Gray
The outputs are NOT frame-locked.
724-746-5500 | blackbox.com
Page 24
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: VideoPlex4 Control Application
Figure 6-8. Monitor outputs screen.
Individual monitor outputs can be configured by clicking on the corresponding Modify button. This will bring up a timing dialog
similar to that of the input timings. This dialog is shown in Figure 6-9.
Figure 6-9. Timing dialog box.
724-746-5500 | blackbox.com
Page 25
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: VideoPlex4 Control Application
The source of mode selection controls whether the VideoPlex4 output should take its timing values and resolution from the
preferred mode of the monitor that is connected, or use its internally programmed “default” mode.
NOTE: You can edit only the internal default timings in this dialog.
If “Use the Monitors Preferred Mode” is selected, but no valid EDID can be read from the attached monitor, then the VideoPlex4
firmware will program the output using the default mode timings.
The rest of the dialog is identical to that for setting the Input timings, with the exception that for the output monitors, you can
select Analog RGB (“VGA”) output as well as DVI.
All modifications to the “Output” settings can be saved as part of a .vqs file, removing the requirement to input the same settings
again. To save the settings, select the “Save” command in the File menu. To open a saved .vqs file, select the “Open” command.
Use the “Test” button when defining a default mode that you are not sure the attached monitor can support. In test mode, the
output timings are programmed, but they are not saved to non-volatile memory on the VideoPlex4 until you press the “OK”
button to accept the mode.
724-746-5500 | blackbox.com
Page 26
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
724-746-5500 | blackbox.com
Page 27
Download from Www.Somanuals.com. All Manuals Search And Download.
Black Box Tech Support: FREE! Live. 24/7.
Tech support the
way it should be.
Great tech support is just 30 seconds away at 724-746-5500 or blackbox.com.
About Black Box
Black Box provides an extensive range of networking and infrastructure products. You’ll find everything from cabinets and racks
and power and surge protection products to media converters and Ethernet switches all supported by free, live 24/7 Tech support
available in 30 seconds or less.
© Copyright 2013. Black Box Corporation. All rights reserved. Black Box® and the Double Diamond logo are registered trademarks of BB Technologies, Inc.
Any third-party trademarks appearing in this manual are acknowledged to be the property of their respective owners.
VSC-VPLEX4, version 1
724-746-5500 | blackbox.com
Download from Www.Somanuals.com. All Manuals Search And Download.
|