1
2
OPTIONAL ACCESSORIES
CASTER KIT
P/N 430291
To improve maneuverability
on hard paved surfaces.
HOLD DOWN KIT
P/N 430299
For use on truck or trailer to
provide quick hold down for
your QB.
T h a n k Yo u fo r S e l e c t i n g
The Powerful QUIET BLOW® BLOWER
Patent Pending
Operator Owner's Manual
For Models:
QB884H, QB1004, QB1104H
3
Specifications
QB884H
QB1004
QB1104H
Engine: HP
Engine:Type
8.0 HP (5.97 kW )
HONDA OHV
6.4 qt. (6.1 L)
1.16 qt. (1.1 L)
136 # (61.7 Kg)
155 # (70.3 Kq)
52.0 # (23.6 Kg)
10.0HP (7.45kW )
B & S INTEK I/C
4.0 qt. (3.8 L)
0.875 qt.(0.8L)
136 # (61.7 Kg)
155 # (70.3 Kq)
52.0 #(23.6 Kg)
11.0HP (8.2kW )
HONDA OHV
7.4 qt. ( 7.0 L)
1.2 qt.(1.13L)
152 # (68.9 Kg)
169 # (76.7 Kg)
68.4 #(31.0 Kg)
Engine: Fuel cap.
Engine: Oil Cap.
W eight: Unit
W eight: Shipping
Engine W eight:
UNIT SIZE: OVERALL LENGTH: 51.75"(1.31m) OVERALL WIDTH 28.5" (0.72m)
OVERALL HEIGHT
39" (0.99m)
Part No. 430316
Form No. F083100A
Page 1 of 12
Download from Www.Somanuals.com. All Manuals Search And Download.
9
GENERAL SAFETY
·DO NOT place hands or feet inside air intake opening, near
exhaust outlet or near any moving parts.
·DO NOT start engine without deflector attached to exhaust outlet.
·DO NOT direct exhaust outlet toward any bystanders.
·DO NOT operate this equipment without first inspecting
work area.
For your safety and the safety of others, these
directions should be followed:
Do not operate this machine without first reading
owner's manual and engine manufacturer's manual.
Use of Ear Protection is recommended while
operating this machine.
·DO NOT operate this equipment during excessive vibration.
·DO NOT start engine without housing front plate attached.
·DO NOT operate this machine on slopes greater than 20%.
·DO NOT blow any hot or burning debris, or any toxic or
explosive material.
Use of Eye and breathing protection is recom-
mended when using this machine, especially in
dry and dusty conditions.
·DO NOT allow children to operate this equipment.
10
ASSEMBLY
example). Finish installing the other side of the upper handle assembly using
screw (Item 17) and lock nut (Item 32).
2. Install front of handle brace (Item 30), to blower housing using
one screw (Item 17), one washer (Item 58) and one lock nut (item 32).
Install rear of handle brace (item 30) to upper handle vibration mounts using
two lock nuts (item 32). Hand tighten only.
Read all safety and operating instructions
before assembling or starting this unit.
PUT OIL IN ENGINE BEFORE STARTING
Your Billy Goat is shipped from the factory in one carton,
completely assembled except for the upper handle assembly,
handle brace, plate deflector and throttle control.
3. Securely tighten all hardware listed above in steps 1 thru 2.
4. Remove four lock nuts from the front plate and use them to attach the front
wheel bracket (Item 27). Using spacer (Item 18), washer (Item 19), and Lock
Nut (Item 16) to attach Front wheel (Item 23) onto the front wheel bracket.
5.Connect spark plug wire.
1.Install front exhaust wire loop(Item 55) across upper handle and
slide wire loop to lowest possible position on upper handle.
Install upper handle (Item 28), to preassembled lower handle
(item 29) by sliding the upper over and down the outside of the
lower handle. Pull recoil handle from the engine and place it
between rope guides (Item 13). Using screw (Item 22) & lock nut
(Item 32) to install upper handle to lower handle. NOTE: Install
rope guide on the left hand side for the Honda unit and right hand
side for the Briggs & Stratton unit (See fig below for the pictorial
11
PACKING CHECKLIST
Boxing Checklist
Check
Front Exhaust
Director
430315
These items should be included in your carton. If
any of these parts are missing, contact your dealer.
NOTE:Preassemble front
exhaust wire loop(Item 55)
across upper handle before
attaching upper handle to
lower handle.
Check
Wire Loop
Front Exhaust
430336
Check
Handle Upper
Assembly
400957
Check
Handle Brace
400951
Check
Parts Bag &
Parts Bag
& Literature
Assy
Literature Assy
430334
Per Model
Check
Check
Briggs & Stratton
10 HP
Engine
Manual
Per Model
Honda 8 & 11 HP
Check
Check
Denotes parts found in
Parts Bag Assembly
(shown on page 4).
Bracket Front
Wheel 430270
Front Wheel
430271
Page 3 of 12
Download from Www.Somanuals.com. All Manuals Search And Download.
Part No. 430316
Form No. F083100A
12
13
PARTS BAG & LITERATURE ASSY P/N 430334
CONTROLS
PARTS BAG ASSEMBLY CHECKLIST P/N 430340
Throttle Control /
Gust Control
Screw Cap
5/16-18 x 1 1/4
8041029 Qty. 1
Literature Checklist
Owner's
Manual
19
14
Check
Owner's
Manual
430316
Screw Cap
5/16-18 x 1 3/4
8041031 Qty. 1
Washer 1/2 SAE
8172011 Qty. 1
17
22
STOP
Start
Stop
START
Literature
Parts Bag
58
Check
Literature
Parts Bag
430341
STOP
Screw Cap 5/16-18 x 2 1/2
8041034 Qty. 1
START
Washer 5/16 FLAT CUT
8171003 Qty. 1
24
18
Screw Cap 3/8-16 x 3 3/4
8041061 Qty. 1
Check
1
1
Warranty
Card
400972
32
2
2
Warranty
Card
TO LOCK IN MIDDLE
TO LOCK IN MIDDLE
Nut Lock 5/16-18
8160002 Qty. 5
SLIDE LEVER TO RIGHT TO LOCK
AIR DIRECTOR IN MIDDLE POSITION
TO UNLOCK
SQUEEZE THE LEVER TO UNLOCK
AIR DIRECTOR FROM MIDDLE
POSITION
SLIDE LEVER TO RIGHT TO LOCK
AIR DIRECTOR IN MIDDLE POSITION
TO UNLOCK
SQUEEZE THE LEVER TO UNLOCK
AIR DIRECTOR FROM MIDDLE
POSITION
Spacer 1/2 OD x 3.062"
Qty. 1
Check EU Declaration
of Conformity &
EU Distributor
Part No:
430351
Part No:
430333
EU Declaration
of Conformity
& EU
Rope Guide
830533 Qty. 2
List 430189
13
20
16
Briggs &
Stratton
Honda
Distributor List
Nut Lock 3/8-16
8161042 Qty. 1
Cable Ty 1"
900407 Qty. 3
14
15
ENGINE LABELS
INSTRUCTION LABELS
These labels should be included on your Blower. If any of
these labels are damaged, replace them before putting this
equipment into operation. Item and part numbers are given to
help in ordering replacement labels.
Briggs & Stratton
RUN
CHOKE
ON
WARNING
EXPLOSIVE FUEL
STOP ENGINE AND ALLOW TO
COOL BEFORE REFUELING.
DAANNGGEERR
OFF
KEEP HANDS and FEET AWWAY
Label Do Not Fill While
Engine Is Hot
Item 11 Part No.400268
THIS ENGINE EQUIPPED WITH
LOW OIL SENSOR, IF ENGINE WILL
NOT START, CHECK OIL LEVEL
Label Danger Keep Hands and Feet Away
Item 41 Part No.400424
WARNING
Read and follow Operating
Instructions before running engine.
Gasoline is flammable. Allow engine
Label Read Owner's Manual
Item No. 59 Part No. 890301
to cool at least 2 minutes before fueling.
Engines emit carbon monoxide,
DO NOT run in enclosed area.
Label Ear Eye Breathing
DANGER
Honda
Item No. 63 Part No. 890254
READ OWNER’S MANUAL BEFORE OPERATION.
LIRE LE MANUEL D UTILISATEUR AVANT USAGE.
VOR INBETRIEBNAHME UNBEDINGHT BEDIENUNGSANLEITUNG DURCHLESEN.
NO UTILIZAR SINANTES NO HABER LEIDO EL MANUAL
PATENT
PENDING
PART NO. 500183
Label Danger Flying Material
Item No. 44 Part No. 810736
Label Patent No
HONDA MOTOR CO. , LTD. MADE IN JAPAN
Part No. 500183
OIL ALERT
PULL THEN SLIDE TO LOCK
WHEN OIL LEVEL LOW,
ENGINE STOPS IMMEDIATELY.
Label Lever QB Item No. 46
Part No. 430363
Page 4 of 12
Download from Www.Somanuals.com. All Manuals Search And Download.
Part No. 430316
Form No. F083100A
16
OPERATION
Like all mechanical tools, reasonable care must
be used when operating machine.
Side Discharge Up Position
This position allows air to be directed upward during use to avoid
blowing debris into cars or other structures, or to avoid blowing
landscaped areas that would be damaged by the high speed air.
This position also allows operator to maneuver the machine
relative to the work area without disturbing the debris.
Inspect machine work area and machine before operat-
ing. Make sure that all operators of this equipment are
trained in general machine use and safety.
INTENDED USE: This machine is designed for cleaning
outdoor surfaces, where the debris can be effectively
blown into a consolidated area for convenient pickup and
removal.
Do not operate if excessive vibration occurs. If excessive
vibration occurs, shut engine off immediately and check for
damaged or worn impeller, loose impeller bolt, loose
impeller key, loose engine or lodged foreign objects. Note:
See parts list for proper impeller bolt torque specifications.
(See trouble shooting section on page 12).
PUT OIL IN ENGINE BEFORE STARTING
16.1
STARTING
ENGINE: See engine manufacturer’s instructions
for type and amount of oil and gasoline used.
Engine must be level when checking and filling oil and
gasoline.
FUEL VALVE: Move fuel valve to "ON" position (when
provided on engine).
Side Discharge Straight Position
STOP SWITCH: Located on the engine. "ON" position.
CHOKE: Operated with choke lever on side of engine .
THROTTLE: Controlled by throttle lever on the handle. Move
remote throttle control to fast position. Pull starting rope to
start engine.
This position directs the air parallel to the ground for the
majority of blowing operations. The hand control allows the
operator to lock the air stream in this straight out position. To
LOCK the air in position simply pull back on the lever and pull
the lever sideways to the right until the lock engages. See
instruction label on the control.
ENGINE SPEED: Under normal conditions, operate at
minimum throttle to accomplish your current cleaning task.
IF YOUR UNIT FAILS TO START:
Slide over to right to
lock in middle position
See Troubleshooting on page 12.
16.2
HANDLING & TRANSPORTING:
Using two people to lift machine is recommended. Lift holding the
handle and handle brace. Secure in place during transport.
16.3
BLOWING OPERATION
Your Billy Goat blower is equipped with a remote exhaust
director to allow the operator to direct the air stream up or down
as required to assist in moving debris. This feature is extremely
useful when debris has piled up to the point that it cannot be
blown any farther. The air stream can be directed upward to
blow the top of the debris pile over and allow the operator to
continue moving more debris farther.
Page 5 of 12
Download from Www.Somanuals.com. All Manuals Search And Download.
Part No. 430316
Form No. F083100A
16
OPERATION
continued
Side Discharge Down Position
16.4
ADJUSTING AIR DIRECTOR
This position directs the air stream down at the ground to
allow the operator to deliver the maximum power to debris
that is stuck or difficult to remove. This position is also
very useful for cleaning out cracks and expansion joints in
pavement.
When you lock the lever, the default position of air director is in the
middle or straight out. If you want to raise or lower air director lock
position you must adjust the threaded fitting on the cable.
Note: You will not get full range of motion of air director If
you raise or lower default locking postion.
Raise Lock Position
1. Lock the air director in
place at the handle by
pulling on the lever then
slide it over to right.
2. Loosen the top nut on the
threaded cable fitting until
the air director position is
satisfactory.
3. Tighten the bottom nut.
Lower Lock Position
1. Lock the lever at the
handle by pulling on the
lever then slide it over to
right.
Front Discharge Position
The removable front discharge adapter can be slipped
on to direct the air stream forward. This option is
extremely useful for cleaning out long cracks in pave-
ment or for cleaning under bushes or building over-
hangs.
2. Loosen the bottom nut on
the threaded cable fitting
and back it off 1/4 inch.
3. Pull the threaded cable
fitting up while pushing down
on the air director then
check for air director
position.
4. Loosen or tighten the same bottom nut then repeat step 3 until the air
director position is satisfactory.
5. Tighten the top nut.
16.5
STORAGE
Never store engine indoors or in enclosed poorly ventilated areas
with fuel in tank, where fuel fumes may reach an open flame, spark or
pilot light, as on a furnace, water heater, clothes dryer or other gas
appliance.
If engine is to be unused for 30 days or more, prepare as follows:
Remove all gasoline from carburetor and fuel tank to prevent gum
deposits from forming on these parts and causing possible malfunction
of engine. Drain fuel outdoors, into an approved container, away from
open flame. Be sure engine is cool. Do not smoke. Run engine until
fuel tank is empty and engine runs out of gasoline.
NOTE: Fuel stabilizer (such as Sta-Bil) is an acceptable alternative
in minimizing the formation of fuel gum deposits during storage. Add
stabilizer to gasoline in fuel tank or storage container. Always follow
mix ratio found on stabilizer container. Run engine at least 10 min.
after adding stabilizer to allow it to reach the carburetor.
Part No. 430316
Form No. F083100A
Page 6 of 12
Download from Www.Somanuals.com. All Manuals Search And Download.
17
MAINTENANCE
17.3
IMPELLER REMOVAL
Use only a qualified mechanic for
any adjustments, disassembly or any
kind of repair .
1. Wait for engine to cool and disconnect spark plug.
2. Remove front wheel (item 23),and front wheel bracket
(item 27).
3. Remove housing front plate (item 4), by removing nine
(9) screws (item 12), around outside of front plate.
4. Remove impeller bolt and lock washer.
WARNING: TO AVOID PERSONAL INJURY, ALWAYS
TURN MACHINE OFF, MAKE SURE ALL MOVING
PARTS COME TO A COMPLETE STOP.
Note: DO NOT pull or pry on impeller blades.
Also, DO NOT remove the 3 nuts securing the
impeller to the hub.The complete impeller assem-
bly must be removed as a nut.
DISCONNECT SPARK PLUGWIRE
BEFORE SERVICING UNIT.
ENGINE: See engine manufacturer
operator's instructions.
5. Pull on center hub backplate area only of impeller. If
impeller slides off freely, proceed to (step 8).
6. Place two crowbars between center hub backplate area
of impeller and housing on opposite sides. Carefully pry
impeller away from engine until it loosens. Using a penetrat-
ing oil can help loosen a stuck impeller.
RECONNECT SPARK PLUG WIRE AND
GUARDS BEFORE STARTING ENGINE.
7. If the impeller does not loosen, obtain a 1” (25.4mm)
longer bolt of the same diameter and thread type as the
impeller bolt. Thread longer bolt by hand into the crankshaft
until bolt bottoms. Using a suitable gear or wheel puller
against the bolt head and the impeller back-plate (near the
blades), remove impeller from shaft.
8. Reinstall new impeller in reverse order of removal.
9. Tighten impeller bolt. Torque impeller bolt (see parts list
on page 7 for proper impeller bolt torque specifications).
17.1
MAINTENANCE SCHEDULE
Follow these hourly maintenance intervals.
Every Use
Every 25
hrs.
Every 5 hrs. or
(Daily)
Maintenance Operation
Engine (See Engine Manual)
Check for excessive vibration
Inspect for loose parts
17.4
TIRE AIR PRESSURE
Inspect for worn or damaged parts
Check at regular intervals and maintain.
Rear Tires - 24 Psi (17 kPa).
Lubricate wheels
Front Tire - 50 Psi (35 kPa).
ENGINE
17.2
When servicing engine refer to specific manufacturers engine
owner's manual. All engine warranty is covered by the specific
engine manufacturer. If your engine requires warranty or other
repair work contact your local servicing engine dealer. When
contacting a dealer for service it is a good idea to have your
engine model number available for reference(See table page 11).
If you can not locate a servicing dealer in your area you can
contact the manufacturers national service organization.
To reach:
Briggs & Stratton: 800-233-3723
American Honda: 800-426-7701
Page 7 of 12
Download from Www.Somanuals.com. All Manuals Search And Download.
Part No. 430316
Form No. F083100A
17
MAINTENANCE
continued
AIR FILTER COVER REMOVAL INSTRUCTION (BRIGGS AND STRATTON)
Removing the air filter cover (for air filter change and throttle control installation)
1. Disconnect spark plug wire.
2. Remove the locknut and the screwcap holding the front part of the handle brace.
3. Remove the screw from the front of the air filter cover (fig 1).
4. Remove the air filter cover by leaning the top of the cover back towards the lower handle and lifting it up (fig 2).
Figure 2
Figure 1
Installing the air filter cover
1. Install air filter on the engine. (fig 3).
2. Slide the bottom of the air filter cover in place and tilt the cover towards the engine (fig 4 & 5)
Note: You must line up the tabs on bottom of the cover to the slots on the air filter housing.
3. Attach the screw (fig 6)
4. Reconnect the front part of the handle brace.
5. Reconnect spark plug wire.
Figure 3
Figure 4
Figure 5
Figure 6
Part No. 430316
Form No. F083100A
Page 8 of 12
Download from Www.Somanuals.com. All Manuals Search And Download.
17
MAINTENANCE
continued
AIR FILTER COVER REMOVAL INSTRUCTION (HONDA)
Removing the air filter cover (for air filter change and throttle control installation)
1. Disconnect spark plug wire.
2. Remove the wingnut on the top of the air cleaner cover (fig. 1).
3. Remove the air filter cover by leaning the air cleaner cover towards the left side of the machine then remove (fig 2).
Figure 2
Figure 1
THROTTLE CONTROL CABLE INSTALLATION
Briggs & Stratton Engine
1. Remove clamp screw and cable
clamp from front of engine (clamp
must be on the left side on engine
control lever. if clamp is on the
right side, change to the left).
2. Insert "z" end of throttle cable
into hole in engine lever, then
secure cable with clamp screw and
cable clamp on the left side of the
engine control lever (DO not
tighten the screw) (Fig 3).
Figure 3
3. Route throttle cable behind
cover through the slots
provided(Fig 4).
4. Put throttle lever in the "fast"
position at the handle.
Figure 4
6. Pull throttle control wire and
casing back then tighten clamp
screw. DO not over tighten (Fig 5).
Figure 5
Honda Engine
1. Remove air cleaner cover by removing wing nut at the top of cover.
2. Remove cable clamp and screw from engine control lever.
3. Attach "z" end of throttle cable through hole in engine control lever.
4. Replace cable clamp and screw but do not tighten.
5. Put throttle lever in "stop" position at the handle.
6. Pull throttle control wire and casing back then tighten clamp screw.
DO not over tighten.
NOTE: If throttle control seems stiff, it may be necessary to
loosen the 10mm locknut on the engine control lever about 1/2 turn
7. Replace air cleaner and wing nut.
Part No. 430316
Page 9 of 12
Download from Www.Somanuals.com. All Manuals Search And Download.
Form No. F083100A
18
PARTS DRAWING
QB884H, QB1004, QB1104H
Part No. 430316
Form No. F083100A
Page 10 of 12
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS
LIST
QB884H
PART NO
QB1004 QB1104H
PART NO QTY PART NO QTY
19
ITEM
DESCRIPTION
QTY
1
ENGINE - 11HP HONDA
-
-
-
-
400931
-
1
-
ENGINE - 10 HP BRIGGS & STRATTON INTEK
ENGINE - 8 HP HONDA
-
-
430352
-
1
-
400937
800177
430314
430182
400965
*9201123
430333
1
2
1
1
1
1
1
-
-
2
3
4
5
6
7
WASHER LOCK 5/16 TWISTED TOOTH
GUST DIRECTOR QB
800177
430314
430182
400965
*9201123
2
1
1
1
800177
430314
430182
400965
*9201123
430333
2
1
1
1
Denotes
parts found
in parts bag
assembly.
PLATE FRONT & GRILL ASSY
IMPELLER ASS’Y
KEY SQUARE 1/4 X 2 1/4
1
1
Notes
*
LABEL CONTROL QB HONDA
LABEL CONTROL QB B&S
1
standard
hardware
that may be
purchased
locally.
430351
430181
850132
-
1
1
1
-
8
9
AXLE
430181
850132
-
1
1
-
430181
-
1
-
WASHER LOCK 7/16 TWISTED TOOTH
WASHER LOCK 3/8 TWISTED TOOTH)
SCREW CAP 7/16-20 x 1-1/4 HEX. HD GR. 5 (TORQUE 60 FT LBS)(81.4N.m)
SCREW CAP 3/8 -24 x 1-1/2 HEX. HD GR. 8 (TORQUE 50 FT LBS)(68N.m)
LABEL DO NOT FILL WHEN ENGINE IS HOT
SHEET METAL SCREW 1/4 x 3/4 DRILL POINT
GUIDE ROPE
400502
-
1
10
800554
-
1
-
800554
-
1
-
-
-
900344
400268
430208
830533
*8041029
*8041010
*8161042
*8041031
430268
8172011
900407
430342
*8041034
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
400268
430208
830533
*8041029
*8041010
*8161042
*8041031
430268
8172011
900407
430342
*8041034
1
9
2
7
1
1
1
1
1
3
2
1
400268
430208
830533
*8041029
*8041010
*8161042
*8041031
430268
8172011
900407
430342
*8041034
1
9
2
7
1
1
9
2
7
1
SCREW CAP 5/16-18 x 1 - 1/4
SCREW CAP 1/4 -20 x 2
NUT LOCK 3/8 -16 THN HEIGHT
SCREW CAP 5/16 -18 x 1¾
1
1
1
1
SPACER 1/2 OD x 3.062"
1
1
3
2
1
1
1
3
2
1
WASHER 1/2 SAE
CABLE TY
GRIP
SCREW CAP 5/16-18 X 2½
WHEEL
&TIRE
ASSY
SCREW CAP, (FRONT AXLE) 3/8-16 x 3 3/4"
CONTROL LEVER QB
WHEEL, REAR
*8041061
430332
400295
430270
430335
400950
400951
*8041031
1
1
2
1
1
1
1
4
*8041061
430332
400295
430270
430335
400950
400951
1
1
2
1
*8041061
430332
400295
430270
430335
400950
400951
*8041031
1
1
2
1
BRACKET (FRONT WHEEL)
HANDLE UPPER ASS’Y (incl. items 14(2), 25, 35(2), 46, 58(2)
HANDLE LOWER
1
1
1
1
1
1
4
HANDLE- BRACE
SCREW CAP 5/16 -18 x 1¾
SCREW CAP 5/16 -18 x 2 1/2
NUT LOCK , 5/16-18 HEX
*8041034
*8160002
430323
-
4
32
33
34
*8160002
430323
*8042030
-
15
1
2
-
15
1
-
*8160002
430323
*8042030
-
15
1
2
-
BUSHING PIVOT BACK
SCREW CAP 5/16 -24 NF x 1½
SCREW CAP 5/16 -24 NF x ¾
VIBRATION MOUNT
*8042026
400173
430255
*8160001
850230
430328
430324
400424
430200
*8172015
810736
*8171002
430363
430349
YES
2
6
1
3
2
1
1
1
1
2
1
1
1
1
-
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
400173
430255
*8160001
850230
430328
430324
400424
430200
*8172015
810736
*8171002
430363
430349
YES
6
1
3
2
1
1
1
1
2
1
1
1
1
-
400173
430255
*8160001
850230
430328
430324
400424
430200
*8172015
810736
*8171002
430363
430349
YES
6
1
3
2
1
1
1
1
2
1
1
1
1
PARTS BAG ASS’Y (INCL ITEMS 32(5), 58 (1), 15(1), 37(1), 20(3), 17(3)
NUT LOCK 1/4 - 20 HEX
RING RETAINING ¾
BRACKET CONTROL BOX WA QB
CABLE GUST CONTROL QB
LABEL DANGER HANDS & FEET
THROTTLE CONTROL
WASHER - FLAT 3/4 S.A.E. (3/16 x 1-1/2 x 1/8 )
LABEL DANGER FLYING MATERIAL
WASHER 1/4 SAE
LABEL LEVER QB
BUSHING PIVOT FRONT
GUARD MUFFLER (COMES W/ ITEM 1 )
SPRING PIVOT EXHAUST
1
430326
430327
890254
430325
400370
430315
430336
430356
-
1
1
1
1
1
1
1
1
-
430326
430327
890254
430325
400370
430315
430336
430356
430355
*8171003
890301
1
1
1
1
1
1
1
430326
430327
890254
430325
400370
430315
430336
430356
-
1
1
1
1
1
1
1
RING RETAINER 5/16"
LABEL EAR EYE BREATING
WIRE PIVOT QB EXHAUST
SPACER ENGINE QB
DEFLECTOR FRONT EXHAUST QB
WIRE FRONT EXHAUST QB
FRAME ASS’Y (INCLUDES 41, 44, 63 )
SPACER ENGINE INTEK
1
1
1
-
WASHER FLAT CUT 5/16 ( 3/8 ID x 7/8 OD x 1/16 )
LABEL READ OWNER'S MANUAL
*8171003
890301
15
11
*8171003
890301
15
1
1
1
Page 11 of 12
Part No. 430316
Form No. F083100A
Download from Www.Somanuals.com. All Manuals Search And Download.
20
Before Requesting Service Review These Suggestions
Possible Cause
TROUBLESHOOTING
Problem
Solution
Poor air performance
Air intake or exhaust clogged.
Clear clog.
Loose or out of balance impeller or loose engine.
Abnormal vibration.
Engine will not start.
Check impeller and replace if required. Check Engine.
Check stop switches, throttle, choke position and gasoline. Connect
spark plug wire. Clean or replace air cleaner. Or contact a qualified
service person.
Stop switch off. Throttle in off position. Engine not in full choke
position. Out of gasoline. Bad or old gasoline. Spark Plug wire
disconnected. Dirty air cleaner.
Contact an engine servicing dealer for engine problems.
Engine problem.
Engine is locked, will not
pull over.
Nut to secure lever is overtightened.
Loosen nut to allow play in control lever.
Control Lever will not lock
in middle position
WARRANTY PROCEDURE
Engine Service and Warranty
Contact your nearest engine manufacturer's authorized
Please fill in the WARRANTY CARD and send the upper part to Billy Goat.
The WARRANTY terms are stated on the lower part which remains with the
user. Whenever a Billy Goat Machine is faulty due to a defect in material
and / or workmanship, the owner should make a warranty claim as follows:
22.1
22
servicing dealer.
Record your machine model, serial number and
date-of-purchase and where purchased
21 Serial Plate
The Machine should be taken to the dealer from whom it was
purchased or to an authorized Billy Goat dealer.
1803 S. Jefferson
P.O. Box 308
The owner should present the remaining half of the Warranty
Registration Card, or, if this is not available, the invoice or receipt.
Lee's Summit,
MO 64063 / USA
Tel (816) 524-9666
L
A
R
The Warranty Claim will be filled in by the authorized Billy Goat Dealer,
who will send it with the faulty part to Billy Goat headquarters.
Fax (816) 524-6983
91
Model
Serial No.
The Quality / Service department at Billy Goat headquarters will study
the claim and parts and will notify their conclusions.
L
A
p
The decision by the Quality / Service department at Billy Goat
headquarters to approve or reject a Warranty claim is final and
binding.
Unit(Weight)
lbs.
Engine Power
kW
99
kg
rpm
min-1
Note: To process a Warranty Claim, it is necessary to quote the Model
& Serial number that are printed on the Billy Goat Serial Plate.
Operator
BILLY GOAT INDUSTRIES INC.
1803 S.W. JEFFERSON SREET / LEE'S SUMMIT, MO. 64082-2312 / USA
PHONE: 816-524-9666 FAX: 816-524-6983
Purchased
from
Purchase
Date
Part No. 430316
Form No. F083100A
Page 12 of 12
Download from Www.Somanuals.com. All Manuals Search And Download.
|