INSTALLATION, USE & CARE MANUAL
FREESTANDING GAS RANGES
DIMENSIONS: 30’’ (762 mm)(W) x 253/16’’ (640 mm)(D) x36’’ (915 mm)(H)
MODELS
A304GGVXE
A304GGVXT
[M7S0GNA4X(2,5)AUG]
[M7S0GNU4X(2,5)AUA]
310447
1
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
WARRANTY AND SERVICE........................................................................................................................................4
IMPORTANT SAFETY INFORMATION ........................................................................................................................5
PRODUCT SPECIFICATIONS.......................................................................................................................................6
INSTALLATION
BEFORE INSTALLATION ............................................................................................................................................7
INSTALLING THE LEGS ..............................................................................................................................................8
INSTALLING THE WORKTOP FRONTGUARD (OPTIONAL) ...........................................................................................8
INSTALLING THE BACKGUARD................................................................................................................................ 10
INSTALLING THE ANTI‐TIP STABILLTY DEVICE.......................................................................................................... 11
INSTALLATION REQUIREMENTS ............................................................................................................................. 11
INSTALLATION ADJACENT TO KITCHEN CABINETS................................................................................................... 12
EXHAUST HOOD INSTALLATION ............................................................................................................................. 12
ELECTRICAL CONNECTION...................................................................................................................................... 13
WIRING DIAGRAM .......................................................................................................................................................13
GAS CONNECTION ................................................................................................................................................. 14
GAS CONVERSION ................................................................................................................................................. 16
STEP 1: PRESSURE REGULATOR ...................................................................................................................................16
STEP 2: SURFACE BURNERS..........................................................................................................................................17
STEP 3: MAIN OVEN BURNER.......................................................................................................................................17
STEP 4: BROILER BURNER ............................................................................................................................................18
STEP 5: VISUAL CHECKS................................................................................................................................................19
STEP 6: MINIMUM FLAME ADJUSTMENT ....................................................................................................................20
INSTALLATION CHECKLLST ..................................................................................................................................... 22
FINAL PREPARATION ............................................................................................................................................. 22
USER MANUAL
ROOM VENTILATION ............................................................................................................................................. 23
SURFACE BURNER LAYOUT .................................................................................................................................... 23
SURFACE COOKING................................................................................................................................................ 24
CONTROL PANEL SYMBOLS..........................................................................................................................................24
SURFACE BURNER OPERATION....................................................................................................................................24
TIPS FOR USING BURNERS CORRECTLY........................................................................................................................25
TIPS FOR USING PANS CORRECTLY ..............................................................................................................................25
OVEN COOKING..................................................................................................................................................... 26
CONTROL PANEL SYMBOLS..........................................................................................................................................26
OVEN SHELVES.............................................................................................................................................................27
GAS OVEN OPERATION ................................................................................................................................................27
CONVECTION COOKING...............................................................................................................................................28
COOKING WITH THE GAS BROILER..............................................................................................................................29
MAINTAINING YOUR RANGE.................................................................................................................................. 30
CLEANING YOUR RANGE........................................................................................................................................ 30
IMPORTANT APPLIANCE INFORMATION ................................................................................................................ 31
3
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY AND SERVICE
All Bertazzoni products carry a 2 year parts and labor warranty.
Service on all Bertazzoni products shall be carried out by factory‐trained professionals only.
For warranty service please contact Customer Service at the numbers indicated below.
CUSTOMER SERVICE
English/spanish hotline
French
(866) 905‐0010
(800) 561‐7625
Fax
(714) 428‐0040
Email
Mailing address
SERVICEPOWER
1503 South Coast drive
Suite 320
Costa Mesa CA 92626
REPLACEMENT PARTS
Only Bertazzoni replacement parts may be used in performing service on the appliance.
Replacement parts are available from factory authorized parts distributors.
AP Wagner
PHONE 716 961 7131 FAX 716 856 4779
Reliable Parts PHONE 206 5758818 FAX 206 5750910
Coast
PHONE 800 821 0244 FAX 604 321 6646
4
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING!
IMPORTANT SAFETY INFORMATION
Read this instruction booklet before installing
and using the appliance.
PLEASE READ AND FOLLOW THESE IMPORTANT
INSTRUCTIONS FOR THE SAFETY OF YOUR HOME
AND OF THE PEOPLE LIVING IN IT.
The manufacturer will not be responsible for
any damage to property or to persons caused by
incorrect installation or improper use of the
appliance.
Save this Manual for local electrical inspector’s
use.
Read and save these instructions for future
reference.
The manufacturer reserves the right to make
changes to its products when considered
necessary and useful, without affecting the
essential safety and operating characteristics.
Observe all governing codes, ordinances and
regulations.
This appliance has been designed for non‐
professional, domestic use only.
WARNING!
If the information in this manual is not followed
exactly, a fire or explosion may result causing
property damage, personal injury or death.
Do not use this appliance to heat a room.
Do not place any pot or pan on the open oven
door. The door is made of glass and it can break
if loaded with a weight.
Do not store or use gasoline or other flammable
substances in the vicinity of this or any other
appliance.
Before beginning installation, please read these
instructions completely and carefully.
Installation and service must be performed by a
qualified installer, service agency or the gas
supplier.
Do not remove permanently affixed labels,
warnings, or plates from the product. This may
void the warranty. ‐Please observe all local and
national codes and ordinances.
In Massachusetts: All gas products must be
installed by a "Massachusetts" licensed plumber
or gasfitter. A "T" handle type manual gas valve
must be installed in the gas line connected to this
appliance.
Please ensure the range is properly grounded.
The installer should leave these instructions with
the consumer who should retain for local
inspector's use and for future reference.
WHAT TO DO IF YOU SMELL GAS
• Do not light any appliance.
The plug should always be accessible.
• Do not touch any electrical switch.
Installation must conform with local codes or in
the absence of codes, the National Fuel Gas Code
NSIZ223.1‐latest edition. Electrical installation
must be in accordance with the National
Electrical Code, ANIS/NFPA70 ‐ latest edition
and/or local codes. IN CANADA: Installation must
be in accordance with the current CAN/CGA‐
B149.1 National Gas Installation Code or
CAN/CGA‐B 149.2, Propane Installation Code
and/or local codes. Electrical installation must be
in accordance with the current CSA C22.1
Canadian Electrical Codes Part 1 and/or local
codes.
• Do not use any phone in your building.
• Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions.
• If you cannot reach your gas suppliers, call the
fire department.
Installation of any gas‐fired equipment should be
made by a licensed plumber. A manual gas shut‐
off valve must be installed in the gas supply line
ahead of the oven in the gas flow for safety and
ease of service.
Warning!
This range can tip. Injury to persons could result.
Install anti-tip device shipped with range. See
Installation Instructions.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
PRODUCT SPECIFICATIONS
Dimensions (insert drawings front, side and back
Weight
Burner power
Auxiliary
Semi‐rapid
Rapid
3400 BTU/h
6100 BTU/h
10400 BTU/h
2800 BTU/h
12000 BTU/h
14500 BTU/h
12000 BTU/h
Dual burner (inner)
Dual burner ( outer)
Oven
broiler
6
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING!
BEFORE INSTALLATION
Do not use aerosol sprays in the vicinity of this
appliance while it is in operation
This appliance shall only be installed by an
authorized professional.
ROOM VENTILATION: An exhaust fan may be
used with the appliance; in each case it shall be
installed in conformity with the appropriate
national and local standards. Exhaust hood
operation may affect other vented appliances; in
each case it shall be installed in conformity with
the appropriate national and local standards.
This appliance shall be installed in accordance
with the manufacturer’s installation instructions.
This appliance must be installed in accordance
with the norms & standards of the country where
it will be installed. The installation of this
appliance must conform to local codes and
ordinances. In the absence of local codes,
Installations must conforms to American National
Standards, National Fuel Gas Code ANSI Z223.1 –
latest edition** or B149.1.
TYPE OF GAS
This appliance is shipped from the factory for use
with natural gas. For use with propane lp gas
please follow the conversion procedure
described on pg. 17. A step by step conversion
procedure is also included with each set of lp gas
nozzles.
The appliance, when installed, must be
electrically grounded in accordance with local
codes or, in the absence of local codes, with the
National Electrical Code, ANSI/NFPA 70.
If local codes permit, a flexible metal appliance
connection with the new AGA or CGA certified
design, max. 5 feet (1,5 m) long, ½” I.D. is
recommended for connecting this appliance to
the gas supply line. Do not bend or damage the
flexible connector when moving the appliance.
GAS PRESSURE
The maximum inlet gas supply pressure incoming
to the gas appliance pressure regulator is 20’’
water column (5 kPa) .
This appliance must be used with the pressure
regulator provided. The regulator shall be
properly installed in order to be accessible when
the appliance is installed in its final location. The
pressure regulator must be set for the type of gas
to be used. The pressure regulator has ½” female
pipe thread. The appropriate fitting must be
determined based on the size of your gas supply
line, the flexible metal connector and the shutoff
valve.
The minimum gas supply pressure for checking
the regulator setting shall be at least 1“ w.c. (249
Pa) above the inlet specified manifold pressure to
the appliance (this operating pressure is 4” w.c.
(1.00 kPa) for Natural Gas and 11” w.c. (2.75 kPa
for LP Gas).
The appliance must be isolated from the gas
supply piping system by closing its individual
manual shutoff valve during any pressure testing
of the gas supply piping system at test pressures
equal to or less than ½ psi (3.5 kPa).
All opening and holes in the wall and floor, back
and under the appliance shall be sealed before
installation of the appliance.
A manual valve shall be installed in an accessible
location in the gas line external to the appliance
for the purpose of turning on or shutting off gas
to the appliance
7
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLING THE LEGS
INSTALLING THE HOB RAIL AND OVEN
HANDLE
Bertazzoni ranges must be used only with the
legs properly installed.
Only model A304GGVXT
The rail and handle are packed with the upstand.
Four height‐adjustable legs are shipped with the
range in the polysterene container situated over
the appliance.
The rail is only available on some models.
Assemble the hob rail and oven handle as shown
in the pictures
Before installing the legs, position the appliance
near its final location as the legs are not suitable
for moving the appliance over long distances.
After unpacking the range, raise it enough to
insert the legs in the appropriate receptacles
situated on the lower part of the appliance.
Lower the range gently to keep any undue strain
from legs and mounting hardware. If possible use
a pallet or lift jack instead of tilting the unit.
Adjust leg height to the desired level by twisting
the inside portion of the leg assembly until the
proper height is reached. Check with a level that
the cooktop is perfectly level.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLING THE WORKTOP
FRONTGUARD
Only model A304GGVXE
To increase the clearance between the front edge
of the worktop and the burners it is possible to
install the worktop frontguard shipped with the
appliance.
To install the front guard, hold it with the pointed
edges looking up. Align the edges of the
frontguard with the appropriate receptacles in
the bottom of the worktop and press firmly until
the frontguard is securely attached to the
worktop.
ATTENTION: once installed the frontguard may
only be removed by disassembling the worktop.
Attempting to remove the frontguard without
disassembling the worktop will result in
permanent damage to the worktop.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
2 lateral screws from the bottom.
INSTALLING THE BACKGUARD
The backguard must be installed prior to
operation of the appliance for appropriate
ventilation of the oven compartment.
The supplied backguard is a 2‐part assembly. The
box also contains a set of metal screws for
securing the backguard to the worktop.
Position the back part of the backguard and
secure it to the worktop tightening 4 screws from
the bottom.
Disassemble the backguard and position the front
part on the worktop. Align the screw holes with
the corresponding holes at the back of the
worktop.
Connect the back and front part of the upstand.
Check for tight assembly.
If the holes are not aligned, partially loosen the
brackets att the back of the worktop as shown
below.
Install the front part of the backguard by
tightening the 2 central screws from the top and
10
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLING THE ANTI‐TIP STABILlTY
INSTALLATION REQUIREMENTS
DEVICE
The anti‐tip bracket shipped with the range must
be properly secured to the rear wall as shown in
the pircture below.
ELECTRICAL
A properly‐grounded horizontally‐ mounted
electrical receptacle should be installed no higher
than 3" (7.6 cm) above the floor, no less than 2”
(5 cm) and no more than 8” (20,3 cm) from the
right side (facing product).
The height of the bracket from the floor must be
determined after the range legs have been
adjusted to the desired height and after the
range has been leveled.
Measure the distance from the floor to the
bottom of the anti‐tip bracket receptacle on the
back of the appliance.
Check all local code requirements.
GAS
Position the two anti‐tip brackets on the wall at
the desired height plus 1/8" (0.32 cm). The
brackets must be placed at 2”5/16 (6,0 cm) from
the side of the range. The distance between the
two bracket is 25”1/4 (64,1 cm).
An agency‐approved, properly‐sized manual shut‐
off valve should be installed no higher than 3"
(7.6 cm) above the floor and no less than 2” (5
cm) and no more than 8” (20.3 cm) from the left
side (facing product).
Secure the brackets to the wall with appropriate
hardware.
To connect gas between shut‐off valve and
regulator, use agency‐approved, properly sized
flexible or rigid pipe. Check all local code
requirements.
Slide the range against the wall until the brackets
are fully inserted into their receptacles on the
back of the range.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
EXHAUST HOOD INSTALLATION
INSTALLATION ADJACENT TO KITCHEN
CABINETS
This range will best perform when used with PRO
line Bertazzoni exhaust hoods. These hoods have
been designed to work in conjunction with the
Bertazzoni range and have the same finish for a
perfect look.
This range may be installed directly adjacent to
existing countertop high cabinets (36" or 91.5 cm
from the floor).
For the best look, the worktop should be level
with the cabinet countertop. This can be
accomplished by raising the unit using the
adjustment spindles on the legs.
For maximum performance, the height of the
bottom of the hood from the worktop should be
between 25 1/2" (65 cm) and 31 1/2" (80 cm).
This would typically result in the bottom of the
hood being 61 1/2" (156.2 cm) to 67 1/2" (171.5
cm) above the floor. These measurements
provide for safe and efficient operation of the
hood.
ATTENTION: the range CANNOT be installed
directly adjacent to kitchen walls, tall cabinets,
tall appliances, or other vertical surfaces above
36" (91.4 cm) high. The minimum side clearance
in such cases is 6" (15.2 cm).
Before installation of the exhaust hood, consult
local or regional building and installation codes
for additional specific clearance requirements.
Wall cabinets with minimum side clearance must
be installed 18" (45.7 cm) above the countertop
with countertop height between 35 ½” (90.2 cm)
and 37 ¼” (94.6 cm). The maximum depth of wall
cabinets above the range shall be 13" (33.0 cm)
Refer to the range hood installation instructions
provided by the manufacturer for additional
information.
A
B
30” (76,2 cm)
36” (91,5 cm)
C 13” (33,0 cm)
D 18” (45,7 cm)
E
F
35”1/2(90,2 cm) / 37” ¼ (94,6 cm)
6” (15,2 cm)
G
6” (15,2 cm)
12
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING!
ELECTRICAL CONNECTION
ELECTRICAL SHOCK HAZARD
This unit is manufactured for a polarized,
grounded 120 volt/60 Hz, 15 amp system.
Disconnect electrical power at the circuit
breaker box or fuse box before installing the
appliance.
Electric power consumption is about 300 W.
The minimum of 102 VAC is required for proper
operation of gas ignition systems.
Provide appropriate ground for the appliance.
Use copper conductors only.
The circuit must be grounded and properly
polarized.
Failure to follow these instructions could result
in serious injury or death
The unit is equipped witth a SJT power cord. In
case of replacement, the power cord shall be
replaced with one of the same type, size and
length.
CAUTION
Label all wires prior to disconnecting when
servicing controls. Wiring errors can cause
improper and dangerous operation.
ELECTRICAL GROUNDING
This appliance is equipped with a three‐prong
plug for your protection against shock hazard and
should be plugged directly into a properly
grounded socket. Do not cut or remove the
grounding prong from this plug.
Verify proper operation after servicing.
WIRING DIAGRAM
13
Download from Www.Somanuals.com. All Manuals Search And Download.
MANUAL SHUT‐OFF VALVE
GAS CONNECTION
THIS VALVE IS NOT SHIPPED WITH THE APPLIANC
AND MUST BE SUPPLIED BY THE INSTALLER.
All gas connections must comply with national
and local codes. The gas supply line (service)
must be the same size or greater than the inlet
line of the appliance. This range uses a 1/2" NPT
inlet (see drawing below for details of gas
connection). On all pipe joints use appropriate
sealant resistant to gas.
The manual shut‐off valve must be installed in
the gas service line between the gas hook‐up on
the wall and the appliance inlet, in a position
where it can be reached quickly in the event of an
emergency.
In Massachusetts: A 'T' handle type manual gas
valve must be installed in the gas supply line to
this appliance.
This range can be used with Natural or
LP/Propane gas. The range is shipped from the
factory for use with natural gas.
For LP/propane household installation, the
appliance must be converted by the dealer, by a
factory‐trained professional or by a qualified
licensed plumber or gas service company.
FLEXIBLE CONNECTIONS
In case of installation with flexible couplings
and/or quick‐disconnect fittings, the installer
must use a heavy‐duty, AGA design‐certified
commercial flexible connector of at least 1/2"
(1.3 cm) ID NPT (with suitable strain reliefs) in
compliance with ANSI Z21.41 and Z21.69
standards.
Gas conversion is important for safe and effective
use of the appliance. It is the responsibility of the
dealer and the owner of the range to perform the
appropriate gas conversion following the
directions of the manufacturer.
THE GAS CONVERSION PROCEDURE IS DESCRIBED
IN THIS MANUAL AND IN THE PACKAGE
CONTAINING THE CONVERSION NOZZLES
SHIPPED WITH EVERY RANGE.
In Massachusetts: The unit must be installed
with a 36" (3‐foot) long flexible gas connector.
In Canada: use CAN 1‐6.10‐88 metal connectors
for gas appliances and CAN 1‐6.9 M79 quick
disconnect device for use with gas fuel.
Please provide the service person with this
manual before work is started on the range.
PRESSURE TEST‐POINT STOPPER VALVE
WARNING!
To avoid gas leaks, the pressure test‐point
stopper valve and gasket supplied with the range
must be installed on the gas fitting at the back of
the range according to the diagram below.
DO NOT USE AN OPEN FLAME WHEN CHECKING
FOR LEAKS!
Leak testing of the appliance shall be conducted
according to the manufacturer's instructions.
Before placing the oven into operation, always
check for leaks with soapy water solution or
other acceptable method.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
PRESSURE REGULATOR
Since service pressure may fluctuate with local
demand, every gas cooking appliance must be
equipped with a pressure regulator on the
incoming service line for safe and efficient
operation.
The pressure regulator shipped with the
appliance has has two female threads ½” NPT.
The regulator shall be installed properly in order
to be accessible when the appliance is installed in
its final position.
Manifold pressure should be checked with a
manometer and comply with the values indicated
below:
Natural gas Æ 4.0" W.c.P.
LP/Propane Æ 11.0" W.C.P.
Incoming line pressure upstream from the
regulator must be 1" W.c.P. higher than the
manifold pressure in order to check the
regulator.
The regulator used on this range can withstand a
maximum input pressure of 1/2 PSI (14.0" W.c.P.)
If the line pressure exceeds that amount, a step‐
down regulator is required.
The appliance, its individual shut‐off valve, and
the pressure regulator must be disconnected
from the gas line during any pressure testing of
that system at pressures in excess of 1/2 psig
(3.45 kPa).
The individuaL manual shut‐off valve must be in
the OFF position during any pressure testing of
the gas supply piping system at test pressures
equal to or less than ½ psig (3.45 kPa).
15
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 1: PRESSURE REGULATOR
GAS CONVERSION
The pressure regulator supplied with the
appliance is a convertible type pressure regulator
for use with Natural Gas at a nominal outlet
pressure of 4” w.c. or LP gas at a nominal outlet
pressure of 11” w.c. and it is pre‐arranged from
the factory to operate with one of these
gas/pressure as indicated in the labels affixed on
the appliance, package and Instruction booklet.
WARNING!
Before carrying out this operation, disconnect
the appliance from gas and electricity.
Gas conversion shall be conducted by a factory‐
trained professional.
Call the customer service hotline to identify a
factory‐trained professional near your home.
To convert the regulator for use with other liquid
propane LP gas:
The gas conversion procedure for this range
includes 6 steps:
1. Unscrew by hand the upper cap of the
regulator, remove the white plastic
attachment from the cap, reverse its
direction and screw it again firmly against the
cap. The white plastic attachment has arrows
indicating the position for natural gas (NAT)
and LP gas (LP).
1. Pressure regulator
2. Surface burners
3. Main oven burner
4. Broiler burner
2. Screw by hand the metal cap in the original
position on the regulator.
5. Visual checks prior to closure of oven bottom
panel
6. Adjustment of minimum setting
The conversion is not completed if all 6 steps
have not been concluded properly.
Before performing the gas conversion, locate the
package containing the replacement nozzle
shipped with every range. IMPORTANT: Each
nozzle has a number indicating its flow diameter
printed on the body. Consult the table on page 20
for matching nozzles to burners.
Save the nozzles removed from the range for
future use.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 3: MAIN OVEN BURNER
STEP 2: SURFACE BURNERS
To replace the nozzles of the main oven burner,
start by :
To replace the nozzles of the surface burners, lift
up the burners and unscrew the nozzles shipped
with the range using a 7 mm {sochet wrench).
Remove the oven door
Replace nozzles using the conversion set supplied
with the range or by a Bertazzoni authorized
parts warehouse. Each nozzle has a number
indicating its flow diameter printed on the body.
Consult the table on page 20 for matching nozzles
to burners.
Remove the lower frontal cavity gasket and the
enamelled cavity base plate
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Loosen and the screw V and pull out the burner
from the support being careful not to damage the
ignition plug and the thermocouple
STEP 4: BROILER BURNER
Loosen the screw and pull out the burner from
the support being careful not to damage the
ignition plug and the thermocouple.
Unscrew the nozzle R using a 7 mm. spanner and
replace it with the nozzle for the new type of gas
according to what is indicate in the table below
ATTENTION: pay extra attention to avoid damage
to the igniter and thermocouple.
Using a 7 mm [name of the tool] unscrew the
nozzle. Replace the nozzle using the conversion
set supplied with the range or by a Bertazzoni
authorized parts warehouse. Each nozzle has a
number indicating its flow diameter printed on
the body. Consult the table on page 20 for
matching nozzles to burners.
Re‐install all the parts in revers sequence
Adjust the gap X by setting it to fully open
position.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 5: VISUAL CHECKS
Before reinstalling the bottom panel, the
following visual check must be performed to
ensure that the conversion has been carried out
properly and without damage to other
components of the range.
A) CONNECTION OF THERMOCOUPLES TO
THERMOSTAT
The thermocouples for both broiler and main
oven burner are connected to the same magnet.
Tight gently the two connections alternating
action on the two nuts. Do not fully tighten one
thermocouple before having started to tighten
the second one.
After performing all these visual checks, reinstall
the bottom panel of the oven compartment and
proceed to setting the minimum for each
burner.
B) OVEN IGNITER AND THERMOCOUPLE
POSITION
The appropriate gap between the tip of the spark
plug or thermocouple and the burner shall be
approximately 1/8’’.
The tip of the spark plug or thermocouple must
fully overlap at least the first gas emission hole of
the burner.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
OVEN BURNER
STEP 6: MINIMUM FLAME ADJUSTMENT
WARNING!
1. Set the oven temperature control knob to the
MAXIMUM setting.
2. Close the oven door and operate the oven for
at least 10 minutes.
These adjustments should be made only for use
of the appliance with natural gas. For use with
liquid propane gas, the choke screw must be
fully turned in a clockwise direction.
3. Set the knob to the MINIMUM setting .
4. Remove the knob.
5. With a slotted screwdriver turn the choking
screw (by‐pass screw at the left side of the
thermostat bar) and, while observing the
flame at the same time through the bottom
oven porthole, evaluate the consistency of
the flame so it remains on when switching
quickly from MINIMUM to MAXIMUM
setting.
SURFACE BURNERS
1. Light one burner at a time and set the knob
to the MINIMUM position (small flame).
2. Remove the knob.
3. The range is equipped with a safety valve.
Using a small‐size slotted screwdriver, locate
the choke valve on the valve body and turn
the choke screw to the right or left until the
burner flame is adjusted to desired minimum.
4. Make sure that the flame does not go out
when switching quickly from the MAXIMUM
to the MINIMUM position.
Broiler burner: the broiler burner always
operates at maximum, therefore no minimum
adjustment is required.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Models
A304GGVXE
A304GGVXT
[M7S0GNA4X(2,5)AUG]
[M7S0GNU4X(2,5)AUA]
Burner
Auxiliary
Semi-Rapid
Rapid
Position
Rear L
Injector
diam. [mm.]
0,90
Gas
Type
NG
LP (Propane)
NG
Pressure
[i.w.c.]
4”
Max Rate
[BTU/h] [W]
Min Rate
[BTU/h]
By-pass
[W]
264
diam. [mm]
Regulated
0,29
Regulated
0,36
Regulated
0,47
Regulated
0,29
Regulated
0,65
Regulated
0,54
No by-pass
No by-pass
3400
3400
6100
6100
996
996
1787
1787
900
900
0,54
1,18
0,70
1,55
0,92
0,80
0,49
11”
4”
11”
4”
11”
4”
11”
4”
11”
4”
264
Front R
1500
1500
2500
2500
900
439
439
732
732
LP (Propane)
Rear R
NG
LP (Propane)
NG
10400 3047
10400 3047
Front L Inner
Front L Outer
2800
2800
820
820
264
Dual Burner
LP (Propane)
900
264
N°2 x 1,15
N°2 x 0,70
1,85
NG
LP (Propane)
NG
LP (Propane)
NG
LP (Propane)
12000 3516
12000 3516
14500 4248
14500 4248
12000 3516 Only Max Only Max
12000 3516 Only Max Only Max
4500
4500
3500
3500
1318
1318
1025
1025
Oven
Oven
downside
Oven
1,10
1,70
0,98
11”
4”
11”
Broiler
upside
21
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION CHECKLlST
FINAL PREPARATION
1. Is the range mounted on its legs?
Before using the oven, remove any protective
wrap from the stainless steel.
2. Is the backguard securely connected?
All stainless steel body parts should be wiped
with hot, soapy water and with a liquid stainless
steel cleanser.
3. Has the anti‐tip device been properly
installed?
If buildup occurs, do not use steel wool, abrasive
cloths, cleaners, or powders! If it is necessary to
scrape stainless steel to remove encrusted
materials, soak with hot, wet cloths to loosen the
material, then use a wood or nylon scraper. Do
not use a metal knife, spatula, or any other metal
tool to scrape stainless steel! Scratches are
almost impossible to remove.
4. Does the clearance from the side cabinets
comply with the manufacturers directions?
5. Is the electricity properly grounded?
6. Is the gas service line connected following
the directions of the manufacturer?
Before using the oven for food preparation, wash
the cavity thoroughly with a warm soap and
water solution to remove film residues and any
dust or debris from installation, then rinse and
wiped dry.
7. Have all the proper valves, stoppers and
gasket been installed between the range and
the service line?
8. Has the gas connection been checked for
leaks?
9. Has the range been set for the type of gas
available in the household?
10. Is the ignition of all oven burners functioning
properly?
11. Is the air flow to the over and broiler burners
properly adjusted?
12. Does the flame appear sharp blue, with no
yellow tipping, sooting or flame lifting?
13. Has the minimum setting for all burners been
adjusted?
14. Is the oven and broiler ignition working
properly?
15. Does the oven light work properly?
22
Download from Www.Somanuals.com. All Manuals Search And Download.
USER MANUAL
SURFACE BURNER LAYOUT
Reflect names from brochure
WARNING!
1. Small Burner
2. Medium burner
3. Rapid burner
Do not to cover the holes inside the oven with
aluminium foil.
Do not to cover the worktop with aluminium
foil.
4. Dual burner (Power burner)
Do not store any flammable object or objects
under pressure in the storage compartment.
Keep the area of operation of the range free from
combustible materials, gasoline and other
flammable vapors and liquid.
Do not store dangerous or flammable materials in
the cabinets above the appliance.
Do not use the appliance for space heating.
Do not use aerosol sprays in the vicinity of the
appliance while cooking.
Do not sit or step on the oven door.
Do not use oven compartment for storage.
ROOM VENTILATION
The use of a gas cooking appliance generates
heat and humidity in the room where it is
installed. Proper ventilation in the room is
needed. Make sure the kitchen is equipped with
a range hood of appropriate power (400 CFM
minimum). Activate the exhaust fan/range hood
when possible. Intensive and continuous use of
the appliance may require additional ventilation,
for example by opening a window.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
SURFACE BURNER OPERATION
SURFACE COOKING
THERMOCOUPLE SAFETY VALVE
SYMBOLS
Each surface burner of a Bertazzoni range is
equipped with a thermocouple safety device.
The thermocouple opens the flow of gas to the
burner only when hot. Should the flame go off,
the thermocouple will immediately close the gas
flow to the burner eliminating any risk to your
home.
For faster activation of the thermocouple, always
light the burners on maximum power. This will
allow the thermocouple to reach the optimum
temperature in the fastest time.
ELECTRIC IGNITION
To activate the electric ignition, simply turn the
control knob counter‐clockwise to maximum
power (( position). Press the knob to start the
flow of gas and the ignition spark. The spark will
released at the metal tip of the white ceramic pin
located on the side of the burner. Once the flame
is on, release the control knob gently.
If the flame turns off, repeat the above
procedure.
Burner position (in this case
front left burner).
The dual power‐burner is composed by two
burners (inside and outside). Each burner is
activated by a separate control knob. The two
burners can be operated separately or together
for maximum power. To activate the power‐
burner, turn on the central burner first, then turn
on the external ring.
Maximum
setting
temperature
Recommended
/
control knob position for
burner ignition
ATTENTION: do not ignite burners if the black
burner cap is not installed or not centred. The
flame will be irregular.
Minimum temperature setting
MANUAL IGNITION
Manual ignition is always possible even when the
power is cut off or in the event of power failure.
Turn the control knob counter‐clockwise to the
MAXIMUM position. Light the flame with a
kitchen lighter or with a match.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
TIPS FOR USING BURNERS CORRECTLY
TIPS FOR USING PANS CORRECTLY
WARNING!
ATTENTION!
KEEP CHILDREN AT A SAFE DISTANCE FROM THE
APPLIANCE DURING OPERATION.
Always ensure that bottom and handles of pans
do not protrude from the worktop.
DO NOT ALLOW CHILDREN TO OPERATE THE
APPLIANCE.
When cooking with flammable fat such as oil, do
not leave the range unattended.
1. Always check that the burner caps are
properly installed before operation.
Use pots of the appropriate size on each burner
following the indication of the diagram below.
Burner
Recommended pan size
inches (mm)
Small
3½”‐51/2”(90 – 140)
Medium
Large
51/2”‐ 101/4”(140 – 260)
71/8”‐ 101/4” (180 – 260)
82/3”‐101/4” (220 – 260)
Dual burner
When boiling liquids, turn the knob to the
MINIMUM position once boiling is reached to
avoid overflow. .
2. Verify that the flame of the worktop burners
is completely blue and with regular aspect as
shown below.
Always use pots with matching lid.
Dry the bottom of pans before operation.
Use pots with a flat, thick bottom (except for wok
cooking).
WOK COOKING: always use the wok adapter
supplied with the range. Wok pan external
diameter shall not be smaller than 10” (25cm)
and larger than 16” (40cm).
SIMMERING: use the simmer ring supplied with
the range.
3. Always adjust the burner flame so it does not
extend beyond the edge of the pan.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
OVEN COOKING
SYMBOLS
Convection fan and oven
compartment light switch
Oven compartment light
switch for baking or broiling
Thermal bake selector
Broiler selector
Recommended control knob
position for burner ignition
270F
Mimimum oven temperature
setting
500F
Maximum oven temperature
setting
Oven on/off
Oven status indicator.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
OVEN SHELVES
GAS OVEN OPERATION
Bertazzoni ranges are equipped with commercial
grade shelves and a enamel cooking tray.
Shelves are mounted on the appropriate guides
situated on the sides of the oven compartment.
Insert the shelf between top and bottom guide in
any of the 4 positions available.
THERMOCOUPLE SAFETY VALVE
Bertazzoni gas ovens are equipped with a
thermocouple safety device and a thermostat to
set the proper cooking temperature.
The thermocouple opens the flow of gas to the
burner only when hot. Should the flame go off,
the thermocouple will immediately close the gas
flow to the burner eliminating any risk to your
home.
To keep the oven as clean as possible, cook meat
on the tray .
For faster activation of the thermocouple, always
light the burners on maximum power. This will
allow the thermocouple to reach the optimum
temperature in the fastest time.
When available, always follow recipe book
directions. Personal experience will help to
determine any variations in the values reported
in the table. In any case, it is recommended to
follow the instructions of the specific recipe being
used.
ATTENTION!
When using the oven for the first time it should
be operated for 15‐30 minutes at a temperature
of about 500°F/260°C without cooking anything
inside in order to eliminate any moisture and
odours from the internal insulation.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRIC IGNITION
WARNING!
CONVECTION COOKING
Bertazzoni gas oven are equipped with a
CONVECTION fan.
Always keep the oven door open when lighting
the oven.
In convection mode, the fan situated at the back
of the oven compartment creates horizontal
forced‐air circulation. The advantages of
convection cooking are:
Warning: Do not use the gas oven or broiler in
case of electric power failure
Open the oven door, turn the knob to the
maximum temperature setting, press well the
knob for 1 sec. And relase it, the automatic
ignition system will automatically generate the
spark for 5 seconds and will engage the
termocouple. Then check that the oven burner
flame is and remain correctly lit, and clese the
door.
1. uniform distribution of heat throughout the
oven cavity (meat no longer needs to be turned
while roasting)
2. cooking different types of food at the same
time, without flavour transmission from one dish
to the other.
Pre‐heating the oven is not necessary. For
delicate pastry baking, it is recommended to heat
the oven before inserting the pastry trays.
Do not press the oven knob for more than 2,5
sec. otherwise automatic ignition system lock
itself and it will be necessary to retry the whole
ignition sequence; if the oven burner do not
remain correctly lit at the first attempt, open
the door of the room and wait at least 60 sec.
before to retry to ignite the oven burner.
To activate the convection fan use the selector
placed on control panel.
WARNING
If the oven burner flame is extinguished
accidentally during operation, turn the
temperature control knob counter‐clockwise to
the off position. Wait at least 60 seconds before
attempting to light the oven again.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
the door of the room and wait at least 60 sec.
before to retry to ignite the broiler burner.
COOKING WITH THE GAS BROILER
WARNING
USING THE THERMOMETER
Always keep the oven door open when lighting
the gas broiler.
Only model A304GGVXT
The range is fitted with a device that gives a
quantitative indication of the temperature in the
middle of the oven.
The gas broiler is activated with the same control
knob used for setting the oven temperature.
To activate the broiler, turn the control knob
clockwise in the broiler position.
The broiler burner always operates at maximum
power and therefore there is no temperature
setting.
ELECTRIC IGNITION
Warning: Do not use the gas oven or broiler in
case of electric power failure
Open the oven door, turn the knob to the broiler
position setting, press well the knob for 1 sec.
And relase it, the automatic ignition system will
automatically generate the spark for 5 seconds
and will engage the termocouple. Then check
that the broiler burner flame is and remain
correctly lit, and clese the door.
Do not press the broiler knob for more than 2,5
sec. otherwise automatic ignition system lock
itself and it will be necessary to retry the whole
ignition sequence; if the broiler burner do not
remain correctly lit at the first attempt, open
29
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTAINING YOUR RANGE
CLEANING YOUR RANGE
ATTENTION!
Never use abrasive cleaners!
Scratches on the stainless steel surfaces are
permanent.
REPLACING THE OVEN LIGHT BULB
WARNING!
Disconnect power before servicing unit.
Do not clean the range when hot!
Cleaning after installation: use a stainless steel
cleaning product or wipe to eliminate the glue
residues of the blue protection film after
removal.
To replace the oven light bulb, unscrew the
protection cap that projects out inside the oven.
Spare bulbs are available at factory‐authorized
parts resellers listed on page 4.
Cleaning the worktop: periodically clean the
burner heads, the cast iron pan supports and the
burner caps using warm water. Remove burned
food and fat residues with a rubber spatula . If
food residue prevent the smooth operation of
the control knobs, call the customer servce
hotline to schedule service by a factory‐trained
professional.
Alternatively use commercial bulbs type [list
SPECS]
Cleaning stainless steel: for best results use a
stainless steel cleaner product with a soft sponge
or wipe. Alternatively use a soft sponge or cloth
with a warm soap and water solution. Never use
abrasive powders or liquids!
Cleaning the burner caps: lift the burner caps
from the burner heads and wash them in a warm
soap and water solution. Dry thoroughly before
using them again. Before reinstalling them on the
burner head, check that the gas flow holes are
not clogged with food residues or cleaning
product residues.
COOLING FAN FAILURE
Bertazzoni ranges are equipped with a cooling
fan. The fan starts operating each time the oven
knob is on a position different from 0 (zero).
The fan circulates the air between the control
panel and the oven door, allowing the control
panel and the oven door to remain cool while
cooking.
Cleaning Enamel: enamelled parts should be
cleaned frequently with awarm soap and water
solution applied with a soft sponge or wipe.
Never use abrasive powders or liquids! Do not
leave acid or alkaline substances on the
enamelled parts (such as vinegar, lemon juice,
salt, tomato sauce, etc.). Use a rubber spatula to
remove fat residues.
Malfunction of the cooling fan is indicated by the
FAN FAILURE light situated at the left side of the
control panel. If the light is on, turn off all
burners as soon as possible and call the customer
service hotline to schedule service by a factory‐
trained professional.
Cleaning glass door: clean the glass using a non‐
abrasive sponge or wipe with a warm soap and
warm water solution. Use a rubber spatula to
remove fat residues.
ATTENTION: while cleaning the door, avoid
spillage of food resideues and cleaning products
in the venting holes situated on the top side of
the door. To clean the inside of the oven door,
call a factory‐trained professional.
ATTENTION: for further details about cleaning of
the appliance, please contact your appliance
retailer.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT APPLIANCE INFORMATION
MODEL
______________________________________________________________
DATE INSTALLED
DEALER
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
INSTALLER
_______________________________________________________________
________________________________________________________________
SERVICER
_______________________________________________________________
________________________________________________________________
31
Download from Www.Somanuals.com. All Manuals Search And Download.
BERTAZZONI SpA
Via Palazzina 8
42016 Guastalla RE
ITALY
WWW.BERTAZZONI‐ITALIA.COM
32
Download from Www.Somanuals.com. All Manuals Search And Download.
SPARE PARTS LIST
NUMBER
COMPONENT
DESCRIPTION
A304GGVXE - GAS COOKER
QUANTITY
M7S0GNA4X5AUG
6010008
601758
202631
202432
306003
306002
504160
504161
504162
504187
504186
202629
202550
101413
101048
202591
202526
410571
410572
308034
202444
309010
309141
306024
415071
415054
415084
415077
415064
404187
404505
404497
202407
405077
404188
408077
410745
504211
505013
508025
508021
508043
508034
508042
508040
603020
603019
602039
608046
415086
601991
608047
608047
503137
504128
504129
504130
504204
408084
604070
510507
510508
510509
1
1
WIRE T-ZERO
CIRCUIT DIAGRAM
1
1
1
1
2
7
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
4
2
5
2
3
1
1
2
1
2
1
2
2
1
1
1
1
1
1
2
1
2
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
11
18
38
39
80
81
82
85
BURNERS FLASK
PART FOR DUAL WOK AND SEMI RAPID BURNERS
THERMOSTAT CLIP
SPRING FOR KNOB
COVER FOR SMALL FLAME SPREADER
COVER FOR MEDIUM BURNER
COVER FOR RAPID BURNER
COVER IN FOR DUAL BURNER FLAME SPREADER
COVER OUT FOR DUAL BURNER FLAME SPREADER
UP SUPPORT FOR AXIAL COOLIN FAN
DOWN SUPPORT FOR AXIAL COOLIN FAN
PROTECTION FOR FAN ASSISTED OVEN
BLACK OVEN DRIP TRAY
DISHWARMER BOTTOM
BRIDLE FOR FIXING GAS VALVES
PROFILE FOR GLASS DOOR
PROFILE FOR GLASS DOOR
BUMPER
CROSS MEMBER
RING FOR GRID SUPPORT
INSIDE DOOR SPACER
SPRING FOR SPARK PLUG
SPARK PLUG FOR DUAL BURNER
SPARK PLUG 350MM
SPARK PLUG FOR OVEN AND GRILL mm1600
SPARK PLUG FOR GRILL
ACCUMULATOR 4U
RIGHT GRID FOR OVEN
SHELF OVEN
GRID FOR TRAY
FLASK HINGE
OVEN DOOR HINGE
LEFT GRID FOR OVEN
SIMMER PLATE
FLAP DOOR
OVEN BURNER
SUPPORT FOR GRILL BURNER NOZZLE
THERMOCOUPLE MM300
THERMOCOUPLE MM600
THERMOCOUPLE OVEN BURNER
THERMOCOUPLE ULTRA-RAPID BURNER
THERMOCOUPLE GRILL BURNER
THERMOSTAT ADAPTER
OVEN CONVECTION FAN
COOLING FAN
86
105
106
117
120
138
160
205
206
207
274
311
329
385
424
425
427
429
430
441
442
443
444
446
447
473
478
544
546
561
562
564
566
567
570
611
612
620
623
646
648
649
649
667
670
671
672
675
702
715
760
761
762
COMMUTATOR
OVEN BULB WITH HOLDER
T-ZERO MODULE
TERMINAL SEPARATOR
SMALL WARNING LIGHT
SMALL WARNING LIGHT
THERMOSTAT
SMALL FLAME SPREADER
MEDIUM FLAME SPREADER
RAPID FLAME SPREADER
ULTRA RAPID FLAME SPREADER
ADAPTER FOR WOK BURNER PAN SUPPORT
DASYCHAIN SWITCH
SMALL BURNER
SEMI RAPID BURNER
RAPID BURNER
Download from Www.Somanuals.com. All Manuals Search And Download.
764
881
883
884
886
917
929
930
940
943
945
946
950
964
965
972
510512
502148
502150
502179
502180
200327
202389
202214
201197
308031
403463
403464
403465
408076
408075
202360
4010113
4010177
4010123
4010116
910711
403498
406396
411107
411093
602042
411094
406395
410605
210786
309119
501761
505056
201173
202686
608045
608025
200348
201172
501755
501759
501760
202390
414048
414031
414031
501762
201166
201180
202658
410606
501758
501756
501757
101383
101384
101408
101385
101389
101388
202437
202497
201159
202441
200328
200329
504210
DUAL BURNER
1
1
1
2
1
2
1
2
2
12
1
1
2
1
2
4
5
1
1
7
1
1
2
2
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
4
4
1
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
GAS VALVE BY PASS 036
GAS VALVE BY PASS 065
GAS VALVE BY PASS 029
GAS VALVE BY PASS 047
STAINLESS STEEL SIDE
RIGHT VERTICAL VENT
FEET SUPPORT
FIXING FOR WORK TABLE
BUMPER FOR C.I. GRIDS AND DISHWARMER
HANDLE TERMINAL
HANDLE TERMINAL
FIXING HANDLE TERMINAL
CAST IRON PAN SUPPORT
CAST IRON PAN SUPPORT 2 BURNERS
WORK TABLE FIXING
1041
1043
1049
1058
1143
1406
1407
1410
1411
1415
1419
1421
1508
1602
1603
1608
1609
1614
1615
1617
1622
1624
1626
1627
1628
1631
1639
1644
1645
1645
1646
1685
1686
1687
1705
1801
1803
1804
2016
2017
2031
2032
2057
2097
2098
2099
2130
2171
4301
4302
5140
GAS VALVE KNOB
THERMOSTAT KNOB BLACK
ELECTRIC COMMUTATOR KNOB BLACK
KNOB RING
UPSTAND KIT
TUBE FOR HANDLE
OVEN DOOR GLASS
HANDLE GASKET
GASKET FOR OVEN FRONT 3 SIDE
THERMOSWITCH FOR COOLING FAN
GASKET FOR OVEN FRONT 1 SIDE
INNER OVEN GLASS
STAINLESS STEEL OVEN DOOR
CONTROL PANEL
BRIDLE FOR FIXING GAS VALVES/THERMOSTAT
ALL.TUBE FOR OVEN BURNER
SUPPORT FOR OVEN BURNER NOZZLE
BACK PANEL
CONTROL SUPPORT
SMALL BLUE BUD
SMALL RED BUD
WORK TABLE
FIXING FOR GAS PIPE
GAS COLLECTOR
TUBE FOR RIGHT FRONT BURNER
TUBE FOR RIGHT BACK BURNER
LEFT VERTICAL VENT
S.STEEL LEG
BASE FOR LEGS
BASE FOR LEGS
GRILL THERMOSTAT TUBE
REAR VENT STACK
FRONT VENT STACK
BACK ENCLOSURE METAL PANEL
OVEN GLASS SUPPORT
TUBE FOR LEFT BACK BURNER
TUBE FOR EXTERNAL DUAL BURNER
TUBE FOR INTERNAL DUAL BURNER
OVEN SIDE PANEL BLACK
OVEN SIDE PANEL BLACK
UPPER PART FOR BODY LEFT
BACK OVEN BODY
FRONT PANEL MUFFLE
OVEN BOTTOM PANEL BLACK
OVEN BURNER BASE
OVEN BASE
GRILL PROTECTION
BACK PANEL FOR DISHARMER COMPARTMENT
RIGHT SIDE PROFILE
LEFT SIDE PROFILE
GRILL BURNER
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
SPARE PARTS LIST
NUMBER
COMPONENT
DESCRIPTION
QUANTITY
M7S0GNA4X5AUA
6010008
601758
202631
202432
306003
306002
504160
504161
504162
504187
504186
202629
202550
202436
101413
101048
202591
202526
410571
410572
308034
202444
309010
309141
306024
415071
415054
415084
415077
415064
404187
404212
404497
202407
405077
404188
409057
408077
410604
504211
505013
508025
508021
508043
508034
508042
508040
603020
603019
602039
608046
415086
601991
608047
608047
503137
504128
504129
504130
504204
408084
604070
510507
510508
510509
510512
502148
502150
502179
502180
A304GGVXT - GAS COOKER
1
1
11
18
38
39
80
81
82
WIRE T-ZERO
1
CIRCUIT DIAGRAM
BURNERS FLASK
PART FOR DUAL WOK AND SEMI RAPID BURNERS
THERMOSTAT CLIP
SPRING FOR KNOB
1
1
1
2
7
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
4
2
5
2
3
1
1
2
1
2
1
2
2
1
1
1
1
1
1
1
2
1
2
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
COVER FOR SMALL FLAME SPREADER
COVER FOR MEDIUM BURNER
COVER FOR RAPID BURNER
COVER IN FOR DUAL BURNER FLAME SPREADER
COVER OUT FOR DUAL BURNER FLAME SPREADER
UP SUPPORT FOR AXIAL COOLIN FAN
DOWN SUPPORT FOR AXIAL COOLIN FAN
INSIDE FLAP DOOR
PROTECTION FOR FAN ASSISTED OVEN
BLACK OVEN DRIP TRAY
DISHWARMER BOTTOM
BRIDLE FOR FIXING GAS VALVES
PROFILE FOR GLASS DOOR
PROFILE FOR GLASS DOOR
BUMPER
85
86
105
106
109
117
120
138
160
205
206
207
274
311
329
385
424
425
427
429
430
441
442
443
444
446
447
457
473
478
544
546
561
562
564
566
567
570
611
612
620
623
646
648
649
649
667
670
671
672
675
702
715
760
761
762
764
881
883
884
886
CROSS MEMBER
RING FOR GRID SUPPORT
INSIDE DOOR SPACER
SPRING FOR SPARK PLUG
SPARK PLUG FOR DUAL BURNER
SPARK PLUG 350MM
SPARK PLUG FOR OVEN AND GRILL mm1600
SPARK PLUG FOR GRILL
ACCUMULATOR 4U
RIGHT GRID FOR OVEN
SHELF OVEN
GRID FOR TRAY
FLASK HINGE
OVEN DOOR HINGE
LEFT GRID FOR OVEN
THERMOMETER
SIMMER PLATE
FLAP DOOR
OVEN BURNER
SUPPORT FOR GRILL BURNER NOZZLE
THERMOCOUPLE MM300
THERMOCOUPLE MM600
THERMOCOUPLE OVEN BURNER
THERMOCOUPLE ULTRA-RAPID BURNER
THERMOCOUPLE GRILL BURNER
THERMOSTAT ADAPTER
OVEN CONVECTION FAN
COOLING FAN
COMMUTATOR
OVEN BULB WITH HOLDER
T-ZERO MODULE
TERMINAL SEPARATOR
SMALL WARNING LIGHT
SMALL WARNING LIGHT
THERMOSTAT
SMALL FLAME SPREADER
MEDIUM FLAME SPREADER
RAPID FLAME SPREADER
ULTRA RAPID FLAME SPREADER
ADAPTER FOR WOK BURNER PAN SUPPORT
DASYCHAIN SWITCH
SMALL BURNER
SEMI RAPID BURNER
RAPID BURNER
DUAL BURNER
GAS VALVE BY PASS 036
GAS VALVE BY PASS 065
GAS VALVE BY PASS 029
GAS VALVE BY PASS 047
Download from Www.Somanuals.com. All Manuals Search And Download.
917
929
930
940
943
945
945
946
946
950
950
964
965
200327
202389
202214
201197
308031
403463
403463
403464
403464
403465
403465
408076
408075
202360
4010113
4010177
4010123
4010116
4010117
910711
403497
403498
406396
411107
411107
411093
602042
411094
406395
410605
210785
309119
501761
505056
201173
202686
608045
608025
200433
201172
501755
501759
501760
202390
414048
414031
414031
501762
201166
201180
202658
410606
501758
501756
501757
101383
101432
101408
101385
101389
101388
202437
202497
308036
201159
202642
202441
405078
200328
200329
504210
STAINLESS STEEL SIDE
RIGHT VERTICAL VENT
FEET SUPPORT
FIXING FOR WORK TABLE
BUMPER FOR C.I. GRIDS AND DISHWARMER
HANDLE TERMINAL
HANDLE TERMINAL
HANDLE TERMINAL
HANDLE TERMINAL
FIXING HANDLE TERMINAL
FIXING HANDLE TERMINAL
CAST IRON PAN SUPPORT
CAST IRON PAN SUPPORT 2 BURNERS
WORK TABLE FIXING
2
1
2
2
12
1
1
1
1
2
2
1
2
4
5
1
1
7
1
1
1
1
2
2
2
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
4
4
1
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
2
1
1
1
972
1041
1043
1049
1058
1060
1143
1404
1406
1407
1410
1410
1411
1415
1419
1421
1508
1602
1603
1608
1609
1614
1615
1617
1622
1624
1626
1627
1628
1631
1639
1644
1645
1645
1646
1685
1686
1687
1705
1801
1803
1804
2016
2017
2031
2032
2057
2097
2098
2099
2100
2130
2165
2171
4106
4301
4302
5140
GAS VALVE KNOB
THERMOSTAT KNOB BLACK
ELECTRIC COMMUTATOR KNOB BLACK
KNOB RING
THERMOMETER KNOB RING
UPSTAND KIT
TUBE FOR HANDLE
TUBE FOR HANDLE
OVEN DOOR GLASS
HANDLE GASKET
HANDLE GASKET
GASKET FOR OVEN FRONT 3 SIDE
THERMOSWITCH FOR COOLING FAN
GASKET FOR OVEN FRONT 1 SIDE
INNER OVEN GLASS
STAINLESS STEEL OVEN DOOR
CONTROL PANEL
BRIDLE FOR FIXING GAS VALVES/THERMOSTAT
ALL.TUBE FOR OVEN BURNER
SUPPORT FOR OVEN BURNER NOZZLE
BACK PANEL
CONTROL SUPPORT
SMALL BLUE BUD
SMALL RED BUD
WORK TABLE
FIXING FOR GAS PIPE
GAS COLLECTOR
TUBE FOR RIGHT FRONT BURNER
TUBE FOR RIGHT BACK BURNER
LEFT VERTICAL VENT
S.STEEL LEG
BASE FOR LEGS
BASE FOR LEGS
GRILL THERMOSTAT TUBE
REAR VENT STACK
FRONT VENT STACK
BACK ENCLOSURE METAL PANEL
OVEN GLASS SUPPORT
TUBE FOR LEFT BACK BURNER
TUBE FOR EXTERNAL DUAL BURNER
TUBE FOR INTERNAL DUAL BURNER
OVEN SIDE PANEL BLACK
OVEN SIDE PANEL BLACK
UPPER PART FOR BODY LEFT
BACK OVEN BODY
FRONT PANEL MUFFLE
OVEN BOTTOM PANEL BLACK
OVEN BURNER BASE
OVEN BASE
BUMPER
GRILL PROTECTION
FIXING FOR THERMOMETER
BACK PANEL FOR DISHARMER COMPARTMENT
HINGE FOR FLAP DOOR
RIGHT SIDE PROFILE
LEFT SIDE PROFILE
GRILL BURNER
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Belkin Network Card F5U122 PC User Manual
Bissell Vacuum Cleaner 5288 User Manual
Black Box Switch ACS235A User Manual
Bosch Appliances Whiteboard Accessories 20 User Manual
Briggs Stratton Lawn Mower 1687286 User Manual
Canon Welding System CR DA1 User Manual
Capcom Video Games 13388340286 User Manual
Casablanca Fan Company Fan RAS 4 13 04 User Manual
Casio Digital Camera MA1010 BMF User Manual
Chief Manufacturing Indoor Furnishings PWC 2000 User Manual