PB8253/PB8263 Digital Projector
Installation Series
User's Manual
Welcome
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of contents
Table of contents
3
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Table of contents
Download from Www.Somanuals.com. All Manuals Search And Download.
Important safety instructions
Your BenQ projector is designed and tested to meet the latest standards for safety of
information technology equipment. However, to ensure safe use of this product, it is
important that you follow the instructions mentioned in this manual and marked on the
product.
Safety Instructions
1.
Please read this manual before you
operate your projector. Save it for
future reference.
4.
Always open the lens shutter or
remove the lens cap when the
projector lamp is on.
5.
In some countries, the line voltage is
NOT stable. This projector is designed
to operate safely within a mains
2.
Do not look straight at the projector
lens during operation. The intense
light beam may damage your eyes.
voltage between 100 to 240 volts AC,
but could fail if power cuts or surges
of ±10 volts occur. In areas where the
mains voltage may fluctuate or cut
out, it is recommended that you
connect your projector through a
power stabilizer, surge protector or
uninterruptible power supply (UPS).
3.
When you think service or repair is
required, take the projector only to a
suitably qualified technician.
6.
Do not block the projection lens with
any objects when the projector is
under operation as this could cause
the objects to become heated and
deformed or even cause a fire. To
temporarily turn off the lamp, press
BLANK on the projector or remote
control.
Important safety instructions
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions (Continued)
7.
The lamp becomes extremely hot
during operation. Allow the
projector to cool for approximately
45 minutes prior to removing the
lamp assembly for replacement.
10. Do not place this product on an
unstable cart, stand, or table. The
product may fall, sustaining serious
damage.
11. Do not attempt to disassemble this
projector. There are dangerous high
voltages inside which may cause
death if you should come into
contact with live parts. The only
user serviceable part is the lamp
which has its own removable cover.
Under no circumstances should you
ever undo or remove any other
covers. Refer servicing only to
suitably qualified professional
service personnel.
8.
Do not operate lamps beyond the
rated lamp life. Excessive operation
of lamps beyond the rated life could
cause them to break on rare
occasions.
9.
Never replace the lamp assembly or
any electronic components unless
the projector is unplugged.
6
Important safety instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions (Continued)
12. Do not place this projector in any of the 13. Do not block the ventilation holes.
- Do not place the projector on a blanket,
bedding or any other soft surface.
following environments.
- Space that is poorly ventilated or confined.
Allow at least 50 cm clearance from walls
and free flow of air around the projector.
- Do not cover the projector with a cloth or
any other item.
- Locations where temperatures may
become excessively high, such as the
inside of a car with all windows rolled up.
- Do not place inflammables near the
projector.
- Locations where excessive humidity, dust,
or cigarette smoke may contaminate
optical components, shortening the
projector's life span and darkening the
image.
If the ventilation holes are seriously
obstructed, overheating inside the
projector may result in a fire.
14. Always place the projector on a level,
horizontal surface during operation.
- Do not use if tilted at an angle of more
than 10 degrees left to right, nor at angle
of more than 15 degrees front to back.
Using the projector when it is not fully
horizontal may cause a malfunction of, or
damage to, the lamp.
- Locations near fire alarms
- Locations with an ambient temperature
above 40°C/104°F
- Locations where the altitudes are higher
than 10000 feet.
10000
feet
Important safety instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Safety Instructions (Continued)
15. Do not store the projector on end
vertically. Doing so may cause the
projector to fall over, causing injury or
resulting in damage.
17. Do not place liquids near or on the
projector. Liquids spilled into the
projector may cause it to fail. If the
projector does become wet, disconnect
it from the power supply's wall socket
and call BenQ to have the projector
serviced.
16. Do not step on the projector or place
any objects upon it. Besides probable
physical damage to the projector, doing
so may result in accidents and possible
injury.
18. This product is capable of displaying
inverted images for ceiling mount
installation.
Use only BenQ's Ceiling Mount Kit for
mounting the projector and ensure it is
securely installed.
19. When the projector is under operation,
you may sense some heated air and
odor from its ventilation grill. It is a
normal phenomenon and not a
product defect.
8
Important safety instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Projector features
The projector integrates high-performance optical engine projection and a user-friendly
design to deliver high reliability and ease of use.
The projector offers the following features:
•
•
•
•
•
•
•
•
•
•
•
•
•
High quality manual zoom lens
Full-function remote control with laser pointer
One-key auto-adjustment to display the best picture quality
Digital keystone correction to correct distorted images
Adjustable color balance control for data/video display
Ultra-high brightness projection lamp
Ability to display 16.7 million colors
Multi-language On-Screen Display (OSD) menus
8 sets of preset application mode
Switchable normal and Economic modes to reduce the power consumption
Built-in speakers provide stereo audio reproduction
Component HDTV compatibility (YPbPr)
Two PC input terminals (RGB signal input socket and a shared DVI-A connector) and
one PC output terminal
•
Replaceable dust filter
•
The apparent brightness of the projected image will vary depending on the ambient
lighting conditions, selected input source contrast/brightness settings, and is directly
proportional to projection distance.
•
The lamp brightness will decline over time and may vary within the lamp manufacturers
specifications. This is normal and expected behavior.
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Shipping contents
The projector is shipped with the cables required for connection to a PC and to video
equipment. Carefully unpack and verify that you have all of the items shown below. If any of
these items are missing, please contact your place of purchase.
Standard accessories
The supplied accessories will be suitable for your region, and may differ from those
illustrated.
Projector
Soft carry case
Remote control with batteries
User's manual
Quick start guide
User's manual CD
VGA cable
USB cable
Power cord
PC audio cable
Video cable
Optional accessories
1.
2.
3.
4.
Ceiling mounting kit
Spare lamp kit
Presentation Plus
Dust filter kit
10
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector exterior view
Front/upper side
1.
External control panel
Vent (cool air intake)
Front IR remote sensor
Kensington anti-theft lock slot
AC power cord inlet
Main power switch
Front filter grill
Quick-release buttons
Focus ring and Zoom ring
1
2.
3.
4.
5.
6.
7.
8.
9.
9
2
3
10
4
5
6
11
7
8
10. Projection lens
11. Lens cap
Rear/side view
equipment.
12
13
16
14
15
12. Vent (heated air exhaust)
13. Rear IR remote sensor
15. Rear adjuster feet
16. Side filter cover
14. Connector panel
Lower view
17. Front adjuster feet
18. Speaker grill
17
19. Lamp cover
20. Rear adjuster feet
18
19
20
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Connector panel
21. RGB (PC)/Component video
(YPbPr/ YCbCr) signal input
socket
22. RGB signal output socket
23. Audio (Left/ Right)/Video input
sockets
24. S-Video input socket
25. DVI-I signal input socket
supports DVI-D video signal and
DVI-A PC signal
25
26
21
22
26. RS 232 control port
For external control systems and
used by service personnel.
27. PC Audio input socket
28. USB socket
27
28
23
24
12
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls and functions
Projector
7.
8.
Power
Turns the projector on or off. See
details.
1
2
Source
3
Sequentially selects the input signal
Analog RGB, DVI-A, DVI-D,
Analog YPbPr, S-Video, or
Composite Video. See "Switching
input signal" on page 31 for details.
Menu
4
5
6
7
10
6
11
12
9.
8
Turns on the on-screen display
control menu.
9
1.
Focus ring
When the on-screen menu is
activated, moves the selection focus
down.
Adjusts the focus of the projected image. See
32 for details.
for details.
2.
3.
Zoom ring
Adjusts the size of the image. See "Fine-tuning
Temperature warning light
10. Lamp indicator light
Indicates the status of the lamp.
Lights up or flashes when the lamp
has developed a problem. See
"Indicators" on page 53 for details.
11. Blank
Lights up or flashes if the projector's
temperature becomes too high. See "Indicators"
on page 53 for details.
4.
Power indicator light
Used to hide the screen image. You
can press Blank on the projector or
remote control to bring the image
back. See "Hiding the image" on
page 38 for details.
Lights up when the projector is in standby mode
or under operation. See "Indicators" on page 53
for details.
5.
6.
Exit
12. Auto
Exits and saves the menu settings.
Left/ Right
Automatically determines the best
picture timings for the displayed
image. See "Auto-adjusting the
image" on page 32 for details.
Correct keystoning at the top or bottom of the
projected image.
When the on-screen menu is activated, moves
the selection focus left or right, or make
adjustments.
"Using the menus" on page 42 for details.
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
13
Remote control
2.
3.
ASPECT
12
13
Selects an image aspect ratio to suit the
input signal. See "Selecting a preset
mode" on page 35 for details.
SOURCE
1
2
14
15
Sequentially selects the input signal
Analog RGB, DVI-A, DVI-D, Analog
YPbPr, S-Video, or Composite Video.
for details.
3
4
5
4.
UP, DOWN
16
6
7
When the On-Screen Display (OSD) is
activated, press UP to exit and save
the menu settings.
6
4
8
9
Press DOWN to open the OSD
menu and move the selection focus up
and down. See "Using the menus" on
page 42 for details.
17
18
5.
6.
MUTE
Toggles the projector audio between on
and off.
10
11
19
20
Left, Right
Correct keystoning at the top or
bottom of the projected image.
When the on-screen menu is activated,
moves the selection focus left or right,
or make adjustments.
details.
7.
8.
AUTO
1.
Power
Automatically determines the best
picture settings for the displayed
image. See "Auto-adjusting the image"
on page 32 for details.
Toggles the projector between standby
mode and on.
When the projector is in standby mode,
press once to turn the projector on.
When the projector is on, press twice to
turn the projector to standby.
MENU
Turns the On-Screen Display (OSD)
menu on. Exits and saves the menu
settings. See "Using the menus" on
page 42 for details.
down the projector" on page 40 for details.
14
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
9.
PIP SIZE
15. BLANK
Used to hide the screen image. Press
Selects a suitable PIP size. See "PIP
page 39 for details.
BLANK on the projector or remote
control to restore the image. See
details.
10. PAGE UP and DOWN
Operate your display software
program (on a connected PC) which
responds to page up/down commands
(like Microsoft PowerPoint).
page 38 for details.
16. VOLUME +/-
Increases or decreases the volume
level.
17. LASER pointer
Emits visible laser pointer light for
presentation purposes.
11. PIP POS.
Selects a suitable PIP position. See
on page 39 for details.
The LASER Pointer is a presentation
aid for professionals. It emits visible
red colored light when you press it and
the LED indicator lights up red.
12. LED indicator light
Lights red when any buttons on the
remote control is pressed.
13. MODE
WARNING: Do not look into the laser
light window or shine the laser light
beam on yourself or others. See the
warning messages on the back of the
remote control and the attached ''User
Information'' prior to using it.
Depending upon which input signal is
selected, there are several picture setup
options available. See "Selecting a
preset mode" on page 35 for details.
14. FREEZE
18. PIP SOURCE
Selects a suitable PIP source.
operation" on page 39 for details.
19. DIGITAL ZOOM +/-
Magnifies or reduces the projected
image size.
The image is frozen when FREEZE is
pressed. An icon "
" will display in
the lower right corner of the screen. To
release the function, press FREEZE
again. See "Freezing the image" on
page 38 for details.
20. RETURN
Restores a zoomed projected image to
its original size.
image" on page 32 for details.
Warning messages on the back of the remote control
The laser beam is visible. It is necessary to press and hold the LASER
button for continuous output.
The laser pointer is not a toy. Parents should be mindful of the dangers of
laser energy and keep this remote control out of the reach of children.
See the warning label on the back of your remote control for safe operation on the laser
pointer.
Introduction
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control effective range
Infra-Red (IR) remote control sensors are located on the front and the back of the projector.
The remote control must be held at an angle within 30 degrees perpendicular to the
projector's IR remote control sensors to function correctly. The distance between the remote
control and the sensors should not exceed 6 meters (~ 20 feet).
Make sure that there are no obstacles between the remote control and the IR sensors on the
projector that might obstruct the infra-red beam.
6 m
Remote control batteries
1.
2.
3.
To open the battery cover, turn the remote control over to view its back, push on the
finger grip on the cover and slide it up in the direction of the arrow as illustrated. The
cover will slide off.
Remove any existing batteries (if necessary) and install two AAA batteries observing
the battery polarities as indicated in the base of the battery compartment. Positive (+)
goes to positive and negative (-) goes to negative.
Refit the cover by aligning it with the base and sliding it back down into position. Stop
when it clicks into place.
1
3
2
•
•
•
Avoid leaving the remote control and batteries in an excessive heat or humid
environment like the kitchen, bathroom, sauna, sunroom or in a closed car.
Replace only with the same or equivalent type recommended by the battery
manufacturer.
Dispose of the used batteries according to the manufacturer's instructions and local
environment regulations for your region.
•
•
Never throw the batteries into a fire. There may be danger of an explosion.
If the batteries are dead or if you will not be using the remote control for an extended
period of time, remove the batteries to avoid damage to the remote control from possible
battery leakage.
16
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
Positioning your projector
Choosing a location
Your projector is designed to be installed in one of four possible installation locations:
1.
2.
3.
4.
Floor in front of screen;
Ceiling in front of screen;
Floor at rear of screen;
Ceiling at rear of screen.
I. Floor front
Select this location with the projector placed near the
floor in front of the screen. This is the most common
way to position the projector for quick setup and
portability.
II. Ceiling front
Select this location with the projector suspended
upside-down from the ceiling in front of the screen.
Purchase the BenQ Projector Ceiling Mounting Kit
from your dealer to mount your projector on the
ceiling.
Set
in the Source > Mirror menu after you turn
the projector on.
III. Floor rear
Select this location with the projector placed near the
floor behind the screen.
Note that a special rear projection screen is required.
Set
in the Source > Mirror menu after you turn
the projector on.
IV. Ceiling rear
Select this location with the projector suspended
upside-down from the ceiling behind the screen.
Note that a special rear projection screen and the
BenQ Projector Ceiling Mounting Kit are required
for this installation location.
Set
in the Source > Mirror menu after you turn
the projector on.
Your room layout or personal preference will dictate which installation location you select.
Take into consideration the size and position of your screen, the location of a suitable power
outlet, as well as the location and distance between the projector and the rest of your
equipment.
Positioning your projector
Download from Www.Somanuals.com. All Manuals Search And Download.
17
Safety instructions for ceiling mounting of the
projector
We want you to have a pleasant experience using your BenQ projector, so we need to bring
this safety matter to your attention to prevent damage to person and property.
If you intend to mount your projector on the ceiling, we strongly recommend that you use a
proper fitting BenQ projector ceiling mount kit and that you ensure it is securely and safely
installed.
If you use a non-BenQ brand projector ceiling mount kit, there is a safety risk that the
projector may fall from the ceiling due to an improper attachment through the use of the
wrong gauge or length screws.
You can purchase a BenQ projector ceiling mount kit from the place you purchased your
BenQ projector. BenQ recommends that you also purchase a separate Kensington lock
compatible security cable and attach it securely to both the Kensington lock slot on the
projector and the base of the ceiling mount bracket. This will perform the secondary role of
restraining the projector should its attachment to the mounting bracket become loose.
18
Positioning your projector
Download from Www.Somanuals.com. All Manuals Search And Download.
Obtaining a preferred projected image size
The distance from the projector lens to the screen, the zoom setting, and the video format
each factors in the projected image size.
The maximum (native) resolution of the projector is 1024 x 768 pixels, which is a 4 to 3
aspect ratio (expressed as 4:3). To be able to project a complete 16:9 (widescreen) aspect
ratio image, the projector can resize and scale a widescreen image to the projector's native
aspect width. This will result in a proportionally smaller height equivalent to 75% of the
projector's native aspect height.
16:9 aspect image scaled to a 4:3 aspect
4:3 aspect image in a 4:3 aspect display area
display area
Thus, a 16:9 aspect image will not utilize 25% of the height of a 4:3 aspect image displayed
by this projector. This will be seen as darkened (unlit) bars along the top and bottom
(vertical 12.5% height respectively) of the 4:3 projection display area whenever displaying a
scaled 16:9 aspect image in the vertical center of the 4:3 projection display area.
When determining the position of your projector, you should consider its intended use and
input signal aspect ratios. All inputs (other than component Video being fed a 16:9 aspect
signal) will display in a 4:3 aspect ratio (and will require an additional 33% display height
than that of the scaled 16:9 aspect image projection area).
IMPORTANT: Do not select a permanent projector position based upon a 16:9 projection if you
will ever need to select an input (other than composite Video being fed a 16:9 aspect signal).
The projector should always be placed horizontally level (like flat on a table), and positioned
directly perpendicular (90° right-angle square) to the horizontal center of the screen. This
prevents image distortion caused by angled projections (or projecting onto angled surfaces).
The modern digital projector does not project directly forward (like older style reel-to-reel
film projectors did). Instead, digital projectors are designed to project at a slightly upward
angle above the horizontal plane of the projector. This is so that they can be readily placed
on a table and will project forward and upwards onto a screen positioned so that the bottom
edge of the screen is above the level of the table (and everyone in the room can see the
screen).
If the projector is mounted on a ceiling, it must be mounted upside-down so that it projects
at a slightly downward angle.
of the projected image to be vertically offset from the horizontal plane of the projector.
When ceiling mounted, this refers to the top edge of the projected image.
If the projector is positioned further away from the screen, the projected image size
increases, and the vertical offset also increases proportionately.
When determining the position of the screen and projector, you will need to account for
both the projected image size and the vertical offset dimension, which are directly
proportional to the projection distance.
BenQ has provided a table of 4:3-aspect-ratio screen sizes to assist you in determining the
ideal location for your projector. There are two dimensions to consider, the perpendicular
horizontal distance from the center of the screen (projection distance), and the vertical
offset height of the projector from the horizontal edge of the screen (offset).
Positioning your projector
Download from Www.Somanuals.com. All Manuals Search And Download.
19
How to determine the position of the projector for a given
screen size
1.
2.
Select your screen size.
Refer to the table and find the closest match to your screen size in the left columns
labelled '4:3 Screen Diagonal'. Using this value, look across this row to the right to find
the corresponding average distance from screen value in the column labelled 'Average'.
This is the projection distance.
3.
4.
On that same row, look across to the right column and make note of the vertical Offset
value. This will determine the final vertical offset placement of the projector in
relation to the edge of the screen.
The recommended position for the projector is aligned perpendicular to the
horizontal center of the screen, at the distance from the screen determined in step 2
above, and offset by the value determined in step 3 above.
For example, if you are using a 120 inch screen, the average projection distance is 4432 mm
and with a vertical offset of 302 mm.
If you place the projector in a different position (to that recommended), you will have to tilt
it down or up to center the image on the screen. In these situations, some image distortion
will occur. Use the Keystone function to correct the distortion. See "Correcting keystone" on
page 34 for details.
How to determine the recommended screen size for a
given distance
This method can be used for situations where you have purchased this projector and would
like to know what screen size will fit in your room.
The maximum screen size is limited by the physical space available in your room.
1.
2.
Measure the distance between the projector and where you want to position the
screen. This is the projection distance.
Refer to the table and find the closest match to your measurement in the average
distance from screen column labelled 'Average'. Check that your measured distance is
between the min and max distances listed on either side of the average distance value.
Using this value, look across that row to the left to find the corresponding screen
diagonal listed in that row. That is the projected image size of the projector at that
projection distance.
On that same row, look across to the right column and make note of the vertical Offset
value. This will determine the final placement of the screen in relation to the
horizontal plane of the projector.
3.
4.
For example, if your measured projection distance was 4.8 m (4800 mm), the closest match
in the Average column is 5089 mm. Looking across this row shows that a 3500 mm (3.5 m)
screen is required. If you can only obtain imperial sized screens, the listed screen sizes on
either side of the 3.5 m screen are the 10' and 12' screen.
Checking the min. and max. projection distance values for these screen sizes indicates that
the 4.8 m measured projection distance will need to be reduced to fit the 10' size screen, or
increased to fit the 12' size screen. The projector can be adjusted (using the zoom control) to
display on these different screen sizes at those projection distances. Be aware that these
different screens have different vertical offset values.
20
Positioning your projector
Download from Www.Somanuals.com. All Manuals Search And Download.
Maximum zoom
Minimum zoom
Screen
Center of lens
Offset
Projection distance
4:3 Screen Diagonal
Distance from Screen in mm
Vertical Offset in mm
Feet Inches
mm
Min. length
Average Max. length
(with min.
(with max.
zoom)
1652
zoom)
4
48
1219
1500
1524
1829
2000
2134
2438
2500
2743
3000
3048
3500
3658
4000
4572
5000
5486
6000
7620
1773
2181
2216
2659
2908
3102
3546
3635
3989
4362
4432
5089
5318
5816
6648
7270
7978
8725
11080
1893
2329
2367
2840
3106
3313
3787
3882
4260
4659
4733
5435
5680
6212
7100
7765
8520
9317
11833
121
149
151
181
198
211
241
248
272
297
302
347
362
396
453
495
543
594
754
2033
2065
2479
2710
2892
3305
3389
3718
4066
4131
4743
4957
5421
6196
6776
7436
5
6
60
72
7
8
84
96
9
108
120
144
180
216
300
10
12
15
18
25
8132
10327
There is 3% tolerance among these numbers due to optical component variations. BenQ
recommends that if you intend to permanently install the projector, you should physically test
the projection size and distance using the actual projector in situ before you permanently
install it, so as to make allowance for this projector's optical characteristics. This will help you
determine the exact mounting position so that it best suits your installation location.
Positioning your projector
Download from Www.Somanuals.com. All Manuals Search And Download.
21
Connection
When connecting a signal source to the projector, be sure to:
1.
2.
3.
Turn all equipment off before making any connections.
Use the correct signal cables for each source.
Ensure the cables are firmly inserted.
In the connections shown below, some cables may not be included with the projector (see
"Shipping contents" on page 10). They are commercially available from electronics stores.
Connecting a computer or monitor
Connecting a computer
The projector provides VGA and DVI input sockets that allow you to connect it to a
notebook or desktop computer.
Additionally, you can also connect the projector to a computer via the USB cable so you can
perform paging operations of the application on the PC or notebook. (see "Remote paging
To connect the projector to a notebook or desktop computer (either through a
VGA cable or VGA to DVI-A cable):
•
With a VGA cable
•
With a VGA to DVI-A cable
1.
Take the supplied VGA cable and
connect one end to the D-Sub
output socket of the computer.
Connect the other end of the VGA
cable to the D-Sub/Comp. In signal
input socket on the projector.
1.
Take a VGA to DVI-A cable and
connect the VGA end to the D-Sub
output socket of the computer.
Connect the DVI end of the VGA to
DVI-A cable to the DVI-I signal
input socket on the projector.
2.
2.
3.
4.
If you wish to use the remote paging function (see "Remote paging operations" on
page 38), take the supplied USB cable and connect the larger end to the USB port
of the computer, and the smaller end to the USB socket on the projector.
If you wish to make use of the projector speakers in your presentations, take a
suitable audio cable and connect one end of the cable to the audio output socket of
the computer, and the other end to the PC Audio socket of the projector.
Once connected, the audio can be controlled by the remote control (Volume +/-)
"Mute" on page 45 for details.
22
Connection
Download from Www.Somanuals.com. All Manuals Search And Download.
The final connection path should be like that shown in the following diagram:
Notebook or desktop
computer
VGA to DVI-A
cable
VGA cable
USB cable
PC Audio
cable
•
•
A Mac adapter (an optional accessory) is needed if you are connecting legacy version
Macintosh computers.
Many notebooks do not turn on their external video ports when connected to a projector.
Usually a key combo like FN + F3 or CRT/LCD key turns the external display on/off.
Locate a function key labeled CRT/LCD or a function key with a monitor symbol on the
notebook. Press FN and the labeled function key simultaneously. Refer to your
notebook's documentation to find your notebook's key combination.
Connection
Download from Www.Somanuals.com. All Manuals Search And Download.
23
Connecting a monitor
If you want to view your presentation close-up on a monitor as well as on the screen, you
can connect the RGB signal output socket on the projector to an external monitor with a
VGA or VGA to DVI-A cable following the instructions below:
To connect the projector to a monitor (either through a VGA cable or VGA to
DVI-A cable):
•
With a VGA cable:
•
With a VGA to DVI-A cable:
Note: You monitor must be equipped with a
DVI input socket.
1.
2.
Connect the projector to a computer as described in "Connecting a computer" on
Take a suitable VGA cable (only one
supplied) and connect one end of
the cable to the D-Sub input socket
of the video monitor.
2.
Take a VGA to DVI-A cable and
connect the DVI end of the cable to
the DVI input socket of the video
monitor.
3.
Connect the other end of the cable
to the D-Sub Out socket on the
projector.
3.
Connect the VGA end of the cable to
the D-Sub Out socket on the
projector.
The final connection path should be like that shown in the following diagram:
notebook or desktop
computer
VGA cable
VGA cable
or
VGA to DVI-A
cable
(VGA)
(DVI)
The D-Sub output only works when an appropriate D-Sub input is made to the projector. Be
sure the projector is connecting with the computer using the D-Sub/Comp. In socket, not
the DVI socket.
24
Connection
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Video source devices
You can connect your projector to various Video source devices that provide any one of the
following output sockets:
•
•
•
•
DVI
Component Video
S-Video
Video (composite)
You need only connect the projector to a Video source device using just one of the above
connecting methods, however each provides a different level of video quality. The method
you choose will most likely depend upon the availability of matching terminals on both the
projector and the Video source device as described below:
Best video quality
The best available video connection method is DVI, if your source device is equipped with a
DVI socket. Based on the type of DVI connector you have, you can enjoy a digital or high-
end analog video quality.
source device and other details.
If no DVI source is available, the next best video signal is available by connecting your device
to the projector with a Component Video (not to be confused with composite Video) cable.
Digital TV tuner and DVD players output Component Video natively, so if available on your
devices, they should be your connection method of choice in preference to S-Video or
(composite) Video.
projector to a component video device.
Better video quality
The S-Video method provides a better quality analog video than standard composite Video.
If you have both composite Video and S-Video output terminals on your Video source
device, you should elect to use the S-Video option.
an S-Video device.
Least video quality
Composite Video is an analog video and will result in a perfectly acceptable, but less than
optimal result from your projector, being the least video quality of the available methods
described here.
projector to a composite Video device.
Connecting Audio
The projector has two built-in speakers which are designed to provide audio functionality
accompanying data presentations for business purposes. It is not designed for, nor intended
for audio reproduction use as might be expected in home theatre or home cinema
applications.
If you have a separate sound system, you will most likely want to connect the audio output
of your Video source device to that sound system, instead of to the projector.
The audio connections illustrated in the following sections are provided for informational
purposes only. You need not connect audio to the projector if there is an alternate sound
system available, or if audio is not required.
Connection
Download from Www.Somanuals.com. All Manuals Search And Download.
25
Connecting a DVI source device
The projector provides a DVI-I input socket that allows you to connect it to a DVI source
device like DVD player, or a VGA output device like notebook or desktop computer.
There are three types of DVI connector: DVI-A, DVI-D, and DVI-I. The DVI-I socket is an
integrated connector which supports both formats: DVI-A, and DVI-D.
DVI-A format is used to carry a DVI signal to an analog (VGA) display, or vice-versa.
Although some signal quality is lost from the signal conversion, it still transmits higher
picture quality than standard VGA connection.
DVI-D format is used to directly carry a digital signal to a digital display without signal
conversion. The pure digital connection provides faster and higher image quality than
analog connection, due to the nature of the digital format.
DVI-A and DVI-D formats are non-interchangeable. You cannot connect a DVI-A format
connector to a DVI-D equipment. Make sure what kind of format you need before you
purchase the cable. Or you can purchase a DVI-I cable which will be more useful in any type
of DVI connection situations.
Examine your source device to determine if it has an unused DVI or VGA (D-Sub) output
socket available:
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to a DVI source device through a DVI cable:
For information on connecting a DVI source device to a computer through a VGA to DVI-A
1.
Take the DVI (DVI-D or DVI-I) cable and connect one end to the DVI output socket
of the DVI source device.
2.
3.
Connect the other end of the cable to the DVI-I signal input socket on the projector.
If you wish to make use the projector speakers, take a suitable audio cable and connect
one end of the cable to the audio output sockets of the video device, and the other end
to the PC Audio socket or Audio L/R sockets on the projector.
Once connected, the audio can be controlled by the remote control (Volume +/-) or
"Mute" on page 45 for details.
The final connection path should be like that shown in the following diagram:
AV device
DVI-D or DVI-I cable
Audio cable
26
Connection
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting a Component Video source device
Examine your Video source device to determine if it has a set of unused Component Video
output sockets available:
•
•
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to a Component Video source device:
1.
Take the (optional accessory) Component Video to VGA (D-Sub) adaptor cable and
connect the end with 3 RCA type connectors to the Component Video output sockets
of the Video source device. Match the color of the plugs to the color of the sockets;
green to green, blue to blue, and red to red.
2.
3.
Connect the other end of the Component Video to VGA (D-Sub) adaptor cable (with
a D-Sub type connector) to the D-Sub/Comp. In socket on the projector.
If you wish to make use of the projector speakers, take a suitable audio cable and
connect one end of the cable to the audio output sockets of the video device, and the
other end to the Audio L/R sockets on the projector.
Once connected, the audio can be controlled by the remote control (Volume +/-) or
"Mute" on page 45 for details.
The final connection path should be like that shown in the following diagram:
Component Video
to VGA (D-Sub)
adaptor cable
AV device
Audio
cable
If you connect the projector to a High Definition TV (HDTV) tuner, the following standards
are supported:
•
•
•
480i
576i
720p (50/ 60 Hz)
•
•
•
480p
576p
1080i (50/ 60 Hz)
•
•
Component Video is the only video output that delivers native 16:9 aspect ratio picture.
If the selected video image is not displayed after the projector is turned on and the
correct video source has been selected, check that the Video source device is turned on
and operating correctly. Also check that the signal cables have been connected
correctly.
Connection
Download from Www.Somanuals.com. All Manuals Search And Download.
27
Connecting an S-Video source device
Examine your Video source device to determine if it has an unused S-Video output socket
available:
•
•
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to an S-Video source device:
1.
Take the (optional accessory) S-Video cable and connect one end to the S-Video
output socket of the Video source device.
2.
3.
Connect the other end of the S-Video cable to the S-Video socket on the projector.
If you wish to make use of the projector speakers, take a suitable audio cable and
connect one end of the cable to the audio output sockets of the video device, and the
other end to the Audio L/R sockets on the projector.
Once connected, the audio can be controlled by the remote control (Volume +/-) or
"Mute" on page 45 for details.
The final connection path should be like that shown in the following diagram:
AV device
S-Video cable
Audio cable
•
•
If the selected video image is not displayed after the projector is turned on and the
correct video source has been selected, check that the Video source device is turned on
and operating correctly. Also check that the signal cables have been connected
correctly.
If you have already made a Component Video connection between the projector and this
S-Video source device using Component Video connections, you need not connect to
this device using an S-Video connection as this makes an unnecessary second
connection of poorer picture quality. See "Connecting Video source devices" on page 25
for details.
28
Connection
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting a composite Video source device
Examine your Video source device to determine if it has a set of unused composite Video
output sockets available:
•
•
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to an composite Video source device:
If you wish to make use of the projector speakers,
1.
2.
Take an Audio/Video cable and connect the 3 RCA type connectors to the Audio(R/L)/
Video output sockets of the Video source device. Match the color of the plugs to the
color of the sockets; green to green, blue to blue, and red to red.
Connect the other end of the Audio/Video cable to the Audio(R/L)/Video sockets on
the projector. Match the color of the plugs to the color of the sockets; green to green,
blue to blue, and red to red.
Once connected, the audio can be controlled by the remote control (Volume +/-) or
"Mute" on page 45 for details.
If you need only to use the video function of the projector,
1.
2.
Take the Video cable and connect one end to the Video output socket of the Video
source device.
Connect the other end of the Video cable to the Video socket on the projector.
The final connection path should be like that shown in the following diagram:
AV device
Audio (L/R)/
Video cable
•
•
If the selected video image is not displayed after the projector is turned on and the
correct video source has been selected, check that the Video source device is turned on
and operating correctly. Also check that the signal cables have been connected
correctly.
You need only connect to this device using a composite Video connection if Component
Video and S-Video inputs are unavailable for use. See "Connecting Video source
devices" on page 25 for details.
Connection
Download from Www.Somanuals.com. All Manuals Search And Download.
29
Operation
Start up
1.
Plug the power cord into the projector and into a wall
socket. Turn on the wall socket switch (where fitted).
2.
Remove the lens cap. If it is left on, it could become
deformed due to the heat produced by the projection
lamp.
3.
4.
Turn the main power switch on. The Power
indicator lights orange.
Press and hold (for 2 seconds)
Power on
the remote control or projector to start the
projector. The Power indicator light flashes
green and stays green when the projector is on.
The start up procedure takes about 30 seconds
after pressing
Power. In the later stage of
start up, a default BenQ logo is projected.
5.
6.
Switch all of the connected equipment on.
The projector will start to search for input
signals. The current input source being
scanned displays in the lower right corner of
the screen. The search will continue until an
input source signal is detected.
You can also press SOURCE on the projector or remote control to select your desired
If the frequency/ resolution of the input signal exceeds the projector's operating range, you
will see the message “Out of Range” displayed on a blank screen. Please change to an input
details.
30
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Switching input signal
The projector can be connected to multiple devices
at the same time. However, it can only display one
full screen at a time. To cycle through the available
input sources, press SOURCE on the projector or
remote control. The selected source name will
display in the lower right corner of the screen for 3
seconds after each button press.
The projector features PIP function which allows 2
different signals to be displayed at the same time.
for details.
The brightness level of the projected image will
change accordingly when you switch between
different input signals. Data (graphic) "PC" presentations using mostly static images are
generally brighter than "Video" using mostly moving images (movies). When switching
between different signal inputs, you will need to adjust the ambient lighting conditions for
the best picture quality.
The input type affects the options available for the Preset Mode. See "Selecting a preset
mode" on page 35 for details.
Adjusting the projected image
Adjusting the projection angle
The projector is equipped with 2 quick-release adjuster feet and 2 rear adjuster feet. These
adjusters change the image height and projection angle. To adjust the projector:
1.
Press the quick-release buttons and lift the
front of the projector. Once the image is
positioned where you want it, release the
quick-release buttons to lock the front
adjuster feet in position.
Do not look into the lens while the lamp is on. The
strong light from the lamp may cause damage to
your eyes.
Be careful when you press the adjuster buttons as
they are close to the exhaust vent where hot air comes from.
2.
Screw the rear adjuster feet to fine tune the
horizontal angle.
To retract the foot, hold up the projector while
pressing the quick-release buttons, then slowly
lower the projector. Screw the rear adjuster feet in
a reverse direction.
If the screen and the projector are not
perpendicular to each other, the projected image
becomes vertically trapezoidal. To correct this
situation, adjust the value of Keystone in the
Display menu, on the projector control panel, or on the remote control. See "Correcting
keystone" on page 34 for details.
Operation
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Auto-adjusting the image
In some cases, you may need to optimize the picture
quality. To do this, press AUTO on the projector or
remote control. Within 3 seconds, the built-in
Intelligent Auto Adjustment function will re-adjust
the values of Frequency, and Clock to provide the
best picture quality.
The current source information will be displayed at
the bottom right of the screen for 3 seconds.
The screen will be blank while AUTO is functioning.
Fine-tuning the image size and clarity
1.
Adjust the projected image to the size 2.
that you need using the zoom ring.
Then sharpen the image by rotating
the focus ring.
Searching for details on the image
If you need to find the details on the projected image, press D.
ZOOM + on the remote control, the center of the image will be
magnified. When the + button is pressed again, the image is further
magnified. Use the directional arrows (
,
,
,
) on the
projector or remote control to navigate the image. Pressing D.
ZOOM - reduces the size of the image. When the - button is pressed
again, the image is further reduced until it is restored to the original
size. You can also restore the original size by pressing RETURN on
the remote control.
Any problems?
32
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting the aspect ratio
The "aspect ratio" is the ratio of the image width to the image height. Most analog TV and
computers are in 4:3 ratio, which is the default for this projector, and digital TV is usually in
16:9 ratio.
You can change the projected image ratio (no matter what aspect the source is) by pressing
ASPECT on the remote control. Select an aspect ratio to suit the format of the signal and
your display requirements.
When the selected input source is YPbPr, YCbCr, DVI-D, S-Video, or Video, there are two
aspect ratios available. You can press ASPECT once to show the current setting and press
again to change the current setting. Or you can go to
Image > Auto Resize and press
Left/ Right on the projector or remote control to switch between the two options.
In the pictures below, the grey portions are inactive areas and the white portions are active
areas.
1.
4:3: Scales an image so that it is displayed in the center of the
screen with a 4:3 aspect ratio. This is most suitable for 4:3 images
like computer monitors, standard definition TV, and 4:3 aspect
DVD movies, as it displays them without aspect alteration.
2.
16:9 (default): Scales an image so that it is displayed in the center
of the screen with a 16:9 aspect ratio. This is most suitable for
images which are already in a 16:9 aspect, like high definition TV,
as it displays them without aspect alteration.
16:9 aspect ratio is only sourced through the Component Video input
when being fed an appropriate 16:9 aspect signal. See "Connecting a Component Video
details.
When the selected input source is Analog RGB, DVI-A, or DVI-D, pressing ASPECT sets the
auto-resize function on or off, or sets the image to 16:9 ratio.
You can press ASPECT once to show the current setting and press repeatedly to change the
current setting. Or you can go to
Image > Auto Resize and press Left/ Right on
the projector or remote control to switch between the three options.
1.
2.
3.
On: This is the default for the projector. The pixel resolution of the input signal is
converted to the native resolution of the projector (1024 x 768). For input signals with
lower resolutions, gaps in the pixels are automatically interpolated into the image
before being projected. This may distort the image clarity. If the resolution of the
source image is the same as the projector's (1024 x 768), setting On has no effects.
Off: The image is projected as its original resolution, with no pixel conversion. For
input signals with lower resolutions, the projected image will display smaller than if
resized to full screen. You could adjust the zoom setting or move the projector towards
the screen to increase the image size if necessary. You may also need to refocus the
projector after making these adjustments.
16:9: Scales an image so that it is displayed in the center of the screen with a 16:9 aspect
ratio.
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
33
Optimizing the image
To optimize the image, use the buttons on the projector or remote control to adjust the
image settings directly, or to change the settings on the On-Screen Display (OSD) menus.
The following instructions are optional. You do not need to follow every step. It depends on
the image quality you desire.
Correcting keystone
Keystoning refers to the situation where the projected image is noticeably wider at either the
top or bottom. It occurs when the projector is not perpendicular to the screen.
To correct this, besides adjusting the projection angel
of the projector, you will need to manually correct it
following ONE of these steps.
•
•
Press Left/ Right on the projector or
remote control to display the status bar labelled
Keystone. Press Right to correct keystoning at
the top of the image. Press Left to correct
keystoning at the bottom of the image.
Press MENU on the projector or remote control.
Go to
Display > Keystone and adjust the
values by pressing Left/ Right on the
projector or remote control.
For example,
1. Press
control or
Right on the projector or remote
Right on the projector or remote
2. Press
control when you are in the Display >
Keystone menu.
Keystone
Keystone
0
-6
1. Press
control or
Left on the projector or remote
Left on the projector or remote
2. Press
control when you are in the Display >
Keystone menu.
Keystone
Keystone
0
+6
34
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting a preset mode
The projector is preset with several predefined application modes so
that you can choose one to suit your operating environment and input
source picture type. To select a operation mode that suits your need,
press MODE on the remote control. The picture modes available for
different types of signals are shown below.
PC/DVI-A Signal Input
•
Presentation Mode (Default): Is designed for presentations. The
brightness is emphasized in this mode to match PC and notebook
coloring.
•
•
•
Vivid Mode: Is perfect for playing games. The color saturation and brightness are well-
balanced.
Video Mode: Is suitable for cinematic enjoyment displaying images in their natural
color.
Economic Mode: Use this mode to reduce the system noise and reduce the power
consumption by 20%. The lamp life is also extended with lower light output.
YPbPr/YCbCr/DVI-D/S-Video/Video Signal Input
•
Gaming Mode: Is suitable for playing gamebox-based video games in a normal living
room lighting level environment.
•
•
Video Mode: With a higher color temperature, it is suitable for enjoying TV movies.
Cinema Mode: Is suitable for enjoying DVD movies best viewed in a blackened (little
light) home cinema or lounge room environment.
•
Economic Mode: Use this mode to reduce the system noise and reduce the power
consumption by 20%. The lamp life is also extended with lower light output.
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
35
Other adjustments
If you are not satisfied with the picture quality made by the preset modes, you can manually
adjust some of the settings through the On-Screen Display (OSD) menus.
Adjusting brightness
Press MENU on the projector or remote control. Go to
Display > Brightness and
adjust the values by pressing Left/ Right on the projector or remote control.
The higher the value, the brighter the image. And lower the setting, darker the image. Adjust
this control so the black areas of the image appear just as black and that detail in the dark
areas is visible.
+70
50
-30
Adjusting contrast
Press MENU on the projector or remote control. Go to
Display > Contrast and adjust
the values by pressing Left/ Right on the projector or remote control.
The higher the value, the greater the contrast. Use this to set the peak white level after you
have previously adjusted the Brightness setting to suit your selected input and viewing
environment.
+70
-30
50
Selecting a color temperature
Press MENU on the projector or remote control. Go to
Image > Color Temp and
adjust the values by pressing Left/ Right on the projector or remote control.
The higher the value, the more bluish white the image becomes. The lower the value, the
more reddish white the image becomes.
About color temperatures:
There are many different shades that are considered to be “white” for various purposes. One
of the common methods of representing white color is known as the “color temperature”. A
white color with a low color temperature appears to be reddish white. A white color with a
high color temperature appears to have more blue in it.
36
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating in a high altitude environment
We recommend you use the High Altitude Mode when your environment is higher than
3000 feet above sea level, or is hotter than 40°C, or whenever the projector will be used for
extended periods of time (>10 hours) without shutdown.
To activate the High Altitude Mode, go to
Control > High Altitude Mode, select On
by pressing Left/ Right on the projector or remote control. A confirmation message
displays. Press AUTO.
We recommend you use the High Altitude Mode by selecting On
when your environment is higher than 3000 feet, or is hotter than 40°C.
Do you want to turn on High Altitude Mode?
Yes Auto
No
Next time you turn on the projector, it will show a message pictured below as a reminder
during the start-up.
Current Status
High Altitude Mode
On
This mode is used for protecting projector from extreme environment and may cause high
fan speed.
Operation under "High Altitude Mode" may cause a higher decibel operating noise level
because of increased fan speed necessary to improve overall system cooling and
performance.
If you use this projector under other extreme conditions excluding the above, it may display
auto shut-down symptoms, which is designed to protect your projector from over-heating.
In cases like this, you should switch to High Altitude mode to solve these symptoms.
However, this is not to state that this projector can operate under any and all harsh or
extreme conditions.
Personalizing the projector menu display
The On-Screen Display (OSD) menus can be set according to your preferences. The
following settings do not affect the projection settings, operation, or performance.
•
OSD Time in the Control > OSD menu sets the length of time the OSD will remain
active after your last button press. The time length ranges from 5 to 60 seconds in 5-
second increments.
•
•
Language in the Control menu sets your familiar language for the OSD menus. Use
Left/ Right on the projector or remote control to select your language.
User Logo in the Control > Setup menu allows you to set a preferred logo screen to be
displayed during projector start-up.
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
37
Hiding the image
In order to draw the audience's full attention to the
presenter or other media, you can use BLANK to hide
the projected image when needed. The word 'BLANK'
appears at the bottom right corner of the screen while
the image is hidden. When this function is activated
with a valid audio input connected, the audio can still
be heard. Pressing any key on the projector or remote
control restores the image.
You can set the blank time in the
Control >
Setup > Blank Time menu allowing the projector to
shut down automatically after a period of time when
there is no action taken on the blank screen.
Do not block the projection lens from projecting as this could cause the blocking object to
become heated and deformed or even cause a fire.
Remote paging operations
Connect the projector to your PC or notebook with a USB cable
prior to using this function. See "Connecting a computer" on page 22
for details.
You can operate your display software program (on a connected PC)
which responds to page up/down commands (like Microsoft
PowerPoint) by pressing PAGE or
on the remote control.
If remote paging function doesn't work, check if the USB connection
is correctly made and the mouse driver on your computer is updated
to the latest version.
Freezing the image
The projected image is frozen when FREEZE on the remote control is
pressed. An icon
will display in the lower right corner of the screen.
To release the function, press FREEZE again, RETURN on the remote
control, or SOURCE on the projector or remote control. Note that
pressing the SOURCE button will also change the input source.
Even if an image is frozen on the screen, the pictures are running on the
video or other device. If the connected devices have active audio output,
you will still hear the audio even though the image is frozen onscreen.
Using the laser pointer in the presentation
The LASER Pointer is a presentation aid for professionals. It emits
visible red colored light when you press it and the LED indicator lights
up green.
WARNING: Do not look into the laser light window or shine the laser
light beam on yourself or others. See the warning messages on the back
of the remote control and the attached ''User Information'' prior to using
it.
38
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
PIP (Picture In Picture) operation
Your projector is capable of displaying images simultaneously from two input sources, which
can be used to enhance your presentation in an interesting way.
These functions are available only when the input source is PC and the PIP source is Video
or S-Video.
Operation on the remote control
1.
Ensure both the PC, and Video or S-Video signals are correctly connected to the
projector.
2.
3.
Display the PC image on the screen.
Press PIP-SOURCE on the remote control to display the PIP frame. Press PIP-
SOURCE a second time and wait for the PIP image to display.
To change the position of the PIP image, press PIP-POS. repeatedly until a suitable
position is selected.
4.
5.
To resize the PIP image, press PIP-SIZE repeatedly. There are four options available,
small, medium, large sizes, and off.
More functions are available in the On-Screen Display (OSD) menus.
Operation in the OSD menus
1.
To turn on the OSD menu, press Menu on the projector or MENU on the remote
control.
2.
3.
Use Left/ Right on the projector or remote control to select the
PIP menu.
Use Menu on the projector or Down on the remote control to highlight the PIP
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
39
Shutting down the projector
1.
Press
Power and a confirmation message
will display prompting you as pictured to the
right.
If you don't respond in a few seconds, the
message will disappear.
2.
Press
Power a second time to turn the
projector off. The Power indicator light flashes
orange, the projection lamp shuts down, and
the fans will continue to run for approximately
90 seconds to cool down the projector.
To protect the lamp, the projector will not respond to
any commands during the cooling process.
3.
Turn the main power switch off.
4.
Disconnect the power cord from the wall socket and the projector.
Do not unplug the power cord before the projector shutdown sequence is complete or during
the 90-second cooling down process.
If the projector is not properly shut down, to protect the lamp, when you attempt to re-start the
projector within hours, the fans will run for a few minutes to cool down. Press Power again to
start the projector after the fans stop.
40
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
On-Screen Display (OSD) menu operation
OSD menu system
Functions available when receiving different signal types...
YCbCr (480i/
576i) / S-Video
/ Video
YPbPr (480p/
576p/ 720p/
1080i)
Main
Menu
Analog RGB /
DVI-A
DVI-D
Keystone
Brightness
Contrast
Phase
Keystone
Brightness
Contrast
Phase
Keystone
Brightness
Contrast
Color
Keystone
Brightness
Contrast
H Size
Lamp Hour
Lamp Hour
H Size
Lamp Hour
Ratio
H Position
V Position
Color
Tint
Lamp Hour
Display
Image
Auto Resize
H Position
V Position
Color Temp
Information
Ratio
System
Sharpness
Color Temp
Information
Auto Resize
Color Temp
Information
Tint
Color Temp
Mirror
Source
Volume
Treble
Bass
Source
Mute
Language
OSD -- OSD Pos., OSD Time
Setup -- Source Scan, Keystone Hold, Mirror Hold, Blank Time, Auto Off, User
Logo
Preset Mode --
(PC/DVI-A signal input) Presentation Mode, Vivid Mode, Video Mode, Economic
Mode
Control
(YPbPr/YCbCr/DVI-D/S-Video/Video signal input) Gaming Mode, Video Mode,
Cinema Mode, Economic Mode
Reset
High Altitude
Main Page:
PIP Source
PIP Size
Sub Page:
Brightness
Contrast
Color
N/A
PIP Pos.
H Position
V Position
More Options
Tint
Sharpness
System
PIP
*When a Video or S-Video signal is connected, the function is only available with NTSC
system selected.
Operation
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the menus
The projector is equipped with On-Screen Display (OSD) menus for making various
adjustments and settings.
Please note that the on-screen display (OSD) menus vary according to the signal type
selected.
details.
The following example describes the adjustment of the keystone.
4.
Adjust keystone values by
1.
Press Menu on the projector or
MENU on the remote control to turn
the OSD menu on.
pressing Left/ Right on the
projector or remote control.
5.
Press Exit on the projector or
MENU on the remote control
twice* to leave and save the
setting.
2.
3.
Use Left/ Right on the projector or
remote control to select the
Display menu.
Press Menu on the projector or
Down on the remote control to select
Keystone.
*The first press leads you back to the
main menu and the second press
closes the OSD menu.
42
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Display menu
Some picture adjustments are available only when certain input sources are in use.
Unavailable adjustments are not shown on the screen.
FUNCTION
(default setting /
DESCRIPTION
value)
Corrects any keystoning of the image. See "Correcting keystone" on page
34 for details.
Keystone
(0)
Adjusts the brightness of the image. See "Adjusting brightness" on page
36 for details.
Brightness
(0)
Adjusts the degree of difference between dark and light in the image. See
"Adjusting contrast" on page 36 for details.
Contrast
(0)
This function allows you to adjust the clock
phase to reduce image distortion.
Phase
(depends on the
selected input
source)
Adjusts the horizontal width of the image.
H Size
(0)
Displays the number of hours the lamp has been used.
Increases or decreases the color intensity of the image.
Lamp Hour
Color
(0)
Adjusts the color tones of the image. The higher the value, the more
reddish the image becomes. The lower the value, the more greenish the
image becomes.
Tint
(0)
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
43
Image menu
Some picture adjustments are available only when certain input sources are in use.
Unavailable adjustments are not shown on the screen.
FUNCTION
(default setting /
DESCRIPTION
value)
Automatically resizes the input signal pixel resolution to the native
details.
Auto Resize
(On)
Adjusts the horizontal
position of the projected
image.
H Position
(0)
-30
+30
Adjusts the vertical position
of the projected image.
V Position
(0)
+30
-30
details.
Color Temp
(depends on the
selected input
source)
Shows the current image resolution.
Information
Users have 2 options for the image ratio.
Ratio
(4:3)
1.
2.
4:3 (for a standard screen)
16:9 (for a wide screen)
Increases or decreases the color intensity of the image.
Color
(0)
Adjusts the color tones of the image. The higher the value, the more
reddish the image becomes. The lower the value, the more greenish the
image becomes.
Tint
(0)
Shows the Video input system format, NTSC, PAL, SECAM or YUV.
System
Adjusts the image to make it look sharper or softer.
Sharpness
(0)
44
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Source menu
FUNCTION
(default setting /
value)
DESCRIPTION
The projector can be installed on a ceiling or behind a screen, or with one
or more mirrors. Contact your dealer for the ceiling mount bracket
(optional accessory) if you need to install the projector on your ceiling.
mounting of the projector" on page 18 for details.
Mirror
(Floor front)
Shows the current signal source.
Adjusts the volume level.
Source
Volume
(5)
Adjusts the treble level. (-5 ~ 5)
Adjusts the bass level. (-5 ~ 5)
Treble
(0)
Bass
(0)
On
Off
Mute
(Off)
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
45
Control menu
FUNCTION
(default setting /
DESCRIPTION (default setting / value)
value)
Language sets the language for the OSD control menus.
Language
(English)
Use Left/ Right to select the desired language from among English,
French, German, Italian, Spanish, Russian, Traditional Chinese, Simplified
Chinese, Japanese and Korean.
OSD Pos. (Center-bottom)
Selects a desired OSD position.
OSD
OSD Time (10)
Sets the length of time the OSD will remain active after your last button
press. The range is from 5 to 60 seconds.
Source Scan (On)
Sets whether the projector searches automatically for input signals. If the
source scan is on, the projector will search for input signals until it
acquires a signal. If the function is not activated, the projector selects the
last input signal.
Keystone Hold (0)
When selected, preserves the last keystone correction value even when the
projector is restarted.
Mirror Hold (0)
When selected, preserves the last mirror correction value even when the
projector is restarted.
Setup
Blank Time (0)
Determines the length of time before the projector will automatically
shutdown when Blank is activated.
Auto Off (0)
Sets the length of time before the projector will automatically shutdown
when there is no input signal detected.
User Logo (Default)
Enables the user to select which logo screen will appear during projector
start-up. Three modes are available: Default (BenQ logo), black screen or
blue screen.
Preset modes are provided so you can optimize your projector image set-
up to suit your program type.
Preset Mode
(depends on the
selected input
source)
Returns all settings to the factory preset values.
The following settings will still remain: Phase, System, Language,
Reset
Keystone hold, Mirror hold, User logo, High Altitude, PIP H Position,
PIP V Position, PIP Brightness, PIP Contrast, PIP Color, PIP Tint, and
PIP Sharpness.
46
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
A mode for operation in areas like high altitude or high temperature. See
High Altitude
(Off)
PIP menu
This menu allows you to turn on the PIP screen and make various adjustments to the screen.
FUNCTION
DESCRIPTION
Selects the source for the PIP image. Auto is the recommended PIP
source as the projector will search for a suitable signal automatically.
PIP Source
(Auto)
Press Left/ Right to scroll through the four alternatives: Off, Small,
Medium, Large.
PIP Size
(Off)
Selecting Off closes the PIP image.
When the resolution of the PC signal is 1280 x 1024 (SXGA), the
selected Large PIP size will be reduced to the Medium size.
Selects a desired position for the PIP.
PIP Position
(Upper-left)
Adjusts the horizontal position of the PIP image.
Adjusts the vertical position of the PIP image.
H Position
(0)
V Position
(100)
Press Left/ Right to select more PIP functions including Brightness,
Contrast, Color, Tint, Sharpness and System.
More Options
Adjusts the brightness of the PIP image.
Brightness
(0)
Adjusts the degree of difference between dark and light in the PIP image.
The higher the value, the greater the contrast.
Contrast
(0)
Increases or decreases the color intensity of the PIP image.
Color
(0)
Adjusts the color tones of the PIP image. The higher the value, the more
reddish the image becomes. The lower the value, the more greenish the
image becomes.
Tint
(0)
Adjusts the image to make it appear sharper or softer
Sharpness
(0)
Shows Video input system format, NTSC, PAL, SECAM, or YUV.
System
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
47
Maintenance
Care of the projector
Your projector needs little maintenance. The only thing you need to do on a regular basis is
to keep the lens clean and to clean the dust filters to prevent overheating.
Never remove any parts of the projector except the lamp and dust filter. Contact your dealer
if other parts need replacing.
Cleaning the lens
Clean the lens whenever you notice dirt or dust on the surface.
•
•
Use a canister of compressed air to remove dust.
If there is dirt or smears, use lens-cleaning paper or moisten a soft cloth with lens
cleaner and gently wipe the lens surface.
Never rub the lens with abrasive materials.
Cleaning the projector case
Before you clean the case, turn the projector off using the proper shutdown procedure as
•
•
To remove dirt or dust, wipe the case with the supplied cleaning cloth.
To remove stubborn dirt or stains, moisten a soft cloth with water and a neutral pH
detergent. Then wipe the case.
Never use wax, alcohol, benzene, thinner or other chemical detergents. These can damage the
case.
Storing the projector
If you need to store the projector for an extended time, please follow the instructions below:
•
Make sure the temperature and humidity of the storage area are within the
your dealer about the range.
•
•
•
Retract the adjuster feet.
Remove the batteries from the remote control.
Pack the projector in its original packing or equivalent.
Transporting the projector
It is recommended that you ship the projector with its original packing or equivalent. When
you carry the projector yourself, please use the original box or provided soft carry case.
Cleaning and replacing the dust filters
It is necessary to clean the dust filters periodically. If the filters are not cleaned, they can
become clogged with dust and prevent proper ventilation. This can cause overheating and a
malfunction of the projector.
48
Maintenance
Download from Www.Somanuals.com. All Manuals Search And Download.
A warning message like the one pictured to
the right will be displayed for 10 seconds
every 300 hours of use to remind you to
clean the filters.
Please check if the filter is clean. Please clean the
filter by using a small vacuum or brush if the filter is
dirty.
IMPORTANT: Please ensure that the
projector is properly shutdown before
removing the filters for cleaning or
replacement.
Press Exit to confirm.
This projector has two concealed filters. One is fitted behind the front vent grill (see item 7
Front filter
1A. Access to the front dust filter is located on the right side of the projector towards the
front edge. Use your thumb or finger to pull it out from the side as illustrated in
diagram 'A' below.
1B. If the front filter proves difficult to remove, you should use a broad flat implement
(like an ice-cream stick) to gently lever the filter away from the projector case as
illustrated in diagram 'B' below.
1C. Carefully pull the filter cartridge out from the side of the projector while keeping it
parallel with the front as illustrated in diagram 'C' below
A.
B.
C.
Rear filter
2.
Access to the rear dust filter is located on the left side
of the projector towards the rear. Use your thumb or
finger to pull it out from the side as illustrated below.
3.
To clean the filters, use a small vacuum cleaner
designed for computers and other office equipment,
or use a soft brush (such as a clean artist's
paintbrush) to gently sweep the dust away. Refit and
align the filter sponge to sit snugly within the filter
frame for the front filter, so that no obvious gaps are
visible around the edges between the edge of the filter
sponge and the plastic filter frame housing.
If the dirt is difficult to remove or the filters are
for more service information.
4.
Carefully refit the filters to the projector then press the covers back until they click into
place.
Maintenance
Download from Www.Somanuals.com. All Manuals Search And Download.
49
If the covers are not correctly seated in place, you
will be reminded by a message displayed on the
screen every three minutes. The projector will
automatically shut down after 10 minutes if there
has been no further action taken. Re-install the
filters securely, then turn on the power again.
Please check
Filter not well attached
Lamp information
Use and replacement of the lamp
When the Lamp indicator lights up red or a message displays suggesting it is time to replace
the lamp, please install a new lamp or consult your dealer. An old lamp may cause a
malfunction in the projector and in some instances the lamp may explode.
The Lamp indicator light and Temperature warning light will light up if the lamp becomes too
hot. Turn the power off, allow the projector to cool down before checking that the dust filters
back on, please contact your dealer.
The following Lamp warning displays will remind you to change the lamp.
Message
Status
The lamp has been in operation for 1980 hours. Install
a new lamp for optimal performance. If the projector
is normally run with "Economic Mode" selected (see
"Selecting a preset mode" on page 35), you may
continue to operate the projector until the 2980 hour
lamp warning appears.
The lamp has been in operation for 2980 hour, the
power will shutdown in 20 hours time. A new lamp
should be fitted to avoid the inconvenience when the
projector runs out of lamp time.
The lamp has been in operation for over 3000 hours.
This message will flash in the center of the screen
together with the Lamp indicator lighting up red for
40 seconds. The projector will shutdown after 40
seconds. The lamp MUST be replaced before the
projector will operate normally.
It is strongly recommended that you replace the lamp
at this age. The lamp is a consumable item. With the
usage time increase, the lamp brightness diminished
gradually. This is normal lamp behavior. You can
replace the lamp whenever you notice that the
brightness level has significantly diminished. If the
lamp is not replaced beforehand, it must be replaced
after 3000 hours usage.
50
Maintenance
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the lamp
•
•
•
•
•
To reduce the risk of electrical shock, always turn the projector off and disconnect the
power cord before changing the lamp.
To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes
before replacing the lamp.
To reduce the risk of injuries to fingers and damage to internal components, use caution
when removing lamp glass that has shattered into sharp pieces.
To reduce the risk of injuries to fingers and/or compromising image quality by touching
the lens, do not touch the empty lamp compartment when the lamp is removed.
This lamp contains mercury. Consult your local hazardous waste regulations to dispose
of this lamp in a proper manner.
1.
2.
Turn the power off and disconnect the projector from the wall socket.
Protect the projector's surface by clearing a flat open area on your desk and placing a
soft item on the desk for padding.
3.
Turn the projector over. Then loosen the
screw and remove the lamp cover. If the
lamp is hot, avoid burns by waiting for 45
minutes until the lamp has cooled.
4.
Loosen the screw that fixes the lamp to the
projector. If the screw is not loosened
completely, the lamp cannot be removed.
Be careful not to lose the screw as it is
needed to hold the replacement lamp in
place. It is strongly recommended that you
use a magnetic-head screwdriver.
5.
Lift the handle so that it stands up. Use the
handle to slowly pull the lamp out of the
projector.
•
Pulling too quickly may cause the lamp to
break and scatter broken glass in the
projector.
•
Do not place the lamp in locations where
water might splash on it, children can reach
it, or near flammable materials.
•
Do not insert your hands into the projector
after the lamp is removed. If you touch the optical components inside, it could cause
color unevenness and distortion of the projected images.
6.
Insert the new lamp. Ensure the handle is fully laid flat and locked in place. Reinsert
and tighten the screw firmly.
•
•
A Loose screw may cause a bad connection, which could result in malfunction.
Do not over tighten the screw.
Maintenance
Download from Www.Somanuals.com. All Manuals Search And Download.
51
7.
8.
Re-install the lamp cover and tighten the
screws.
Make connection to a signal source to be
displayed. Start up the projector. (See page
page 30 for turning the power on.)
•
Do not turn the power on with the lamp cover
removed. Whenever the lamp is replaced,
reset the total lamp operation timer.
•
Do not reset if the lamp is not replaced as this
could cause damage.
9.
Reset the lamp counter
i. Press and hold Exit on the
projector for 3 seconds to display
the total used lamp time.
ii. Press Menu on the projector or
MENU on the remote control to
access the lamp hour timer. An
adjustment message will display.
iii. Press Left/ Right on the
projector or remote control to
reset lamp hours and press Exit to leave.
Temperature information
When the Temperature warning light is on, it is warning you of the following possible
problems.
1.
2.
3.
The internal temperature is too high.
Dust filters are clogged.
The fans are not working.
Turn the projector off, check that the dust filters are clean. If the problem persists, contact
qualified service personnel for further help.
For more information, refer to "Indicators" on page 53
52
Maintenance
Download from Www.Somanuals.com. All Manuals Search And Download.
Indicators
Illustration
•
•
Blank -: Light OFF
•
•
O: Orange light
R: Red light
: Light flashing
: Light ON
•
G: Green light
•
LED
Status & Description
Power Temp Lamp
Power events
The projector has just been connected to a power outlet.
Stand-by mode.
O
O
O
O
-
-
-
-
(1) The projector needs 90 seconds to cool down as it was
abnormally shut down without the normal cooling down
process. Or
O
(2) The projector needs to cool for 90 seconds after the power
is turned off.
The Power indicator light is flashing during powering up.
-
-
-
-
G
G
The projector is under normal operation.
Lamp events
The lamp counter has developed a problem.
-
-
-
It is warning you that lamp usage has exceeded 3000 hours.
Replace the projection lamp with a new one immediately.
-
-
R
R
The lamp is not properly attached or the lamp is damaged.
Please contact your dealer for assistance.
-
-
Maintenance
Download from Www.Somanuals.com. All Manuals Search And Download.
53
LED
Status & Description
Power Temp Lamp
Thermal events
-
-
-
-
R
R
R
R
G
G
-
G
G
G
G
G
R
R
R
R
The projector has shutdown automatically. If you try to re-
start the projector, it will shutdown again. Please contact your
dealer for assistance.
-
O
O
O
R
G
G
R
R
G
54
Maintenance
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
The projector does not turn on.
Cause
Remedy
Plug the power cord into the AC inlet on the
projector, and plug the power cord into the
power outlet. If the power outlet has a switch,
make sure that it is switched on.
There is no power from the power
cable.
Attempting to turn the projector on
again during the cooling process.
Wait until the cooling down process has
completed.
No picture
Cause
Remedy
The video source is not turned on or
connected correctly.
Turn the video source on and check that the
signal cable is connected correctly.
The projector is not correctly
connected to the input source device.
Check the connection.
Select the correct input signal with the
SOURCE key on the projector or remote
control.
The input signal has not been
correctly selected.
The lens cover is not open.
Blurred image
Cause
Remove the lens cover.
Remedy
The projection lens is not correctly
focused.
Adjust the focus of the lens using the focus
ring.
The projector and the screen are not
aligned properly.
Adjust the projection angle and direction as
well as the height of the projector if necessary.
The lens cover is not open.
Remove the lens cover.
Clean the lens as described in "Cleaning the
There is dirt or dust on the lens.
Remote control does not work
Cause
Remedy
The batteries are out of power.
Replace the batteries with new ones.
There is an obstacle between the
remote control and the projector.
Remove the obstacle.
You are too far away from the
projector.
Stand within 6 meters (19.5 feet) of the
projector.
Troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
55
The computer projected image is too big for the screen or appeared to be cut-
off
Cause
Remedy
The computer's resolution does not
match the projector's resolution.
1.
2.
3.
Make sure Auto Resize is set to On in
the Image menu.
Make sure the H Position and V Position
settings are correct in the Image menu.
Configure the computer's external
display resolution to the projector's
native resolution (1024 x 768 for
PB8253/PB8263). If this option is not
available, select one of the compatible
listed in "Supported timing for PC
Check if your presentation files are
created for a different resolution.
The computer's external monitor
setting is locked in 640 x 480.
4.
My Window Media Player program works great on my computer, but the
movie window is dark on my projector, while the Media Player tools display
OK.
Cause
Remedy
Change the Display settings. Click Start >
Control Panel > Display > Settings >
Advanced > Display. See you computer
documentation for details, if you cannot find
the Display settings by following the
instructions above. Set the Monitor to Primary,
and the Panel to Secondary. You will see the
movie window on the projector image, while
the Panel movie window will be dark.
The computer external display is set
as a secondary display.
The remote mouse function does not work.
Cause
Remedy
Check the connection. See "Connecting a
computer" on page 22 for details.
If it still doesn't work, check the mouse driver.
See the mouse documentation for details.
The USB cable is not correctly
connected to the projector or
computer.
56
Troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Projector specifications
All specifications are subject to change without notice.
Optical
Resolution
Display system
Lens F/Number
Lamp
1024 x 768 XGA
1-CHIP DMD
F=2.4 to 2.6, f=24.0-29.1 mm
300W lamp
Electrical
Power supply
Power consumption
AC100–240V, 4.5A, 50/60 Hz (Automatic)
395W (Max.)
Mechanical
Weight
7.9 lbs (3.6 Kg)
Input terminal
Computer input
RGB input
D-Sub 15-pin (female) x 1
DVI-I input
(Using DVI-A signal)
Video signal input
S-VIDEO
VIDEO
Mini DIN 4-pin port x 1
RCA jack x 1
SD/HDTV signal input
Analog - D-Sub to Component RCA jack x 3 (using RGB
input)
Digital - DVI (HDTV only)
Audio signal input
PC Audio
Audio L/R
Stereo mini jack x 1
RCA jack x 2
Output
RGB output
Speaker
D-Sub 15-pin (female) x 1
(Stereo) 1 watt x 2
Control
USB mouse control
RS-232 serial control
A/B series x 1
Mini Din 9 pin x 1
Environmental Requirements
Operating temperature
0°C ~ 40°C at sea level
Operating relative humidity 10% ~ 90% (without condensation)
Operating altitude
•
•
•
0–3000 feet at 0°C–40°C
3000–6000 feet at 0°C–30°C
6000–10000 feet at 0°C–23°C
Specifications
Download from Www.Somanuals.com. All Manuals Search And Download.
57
Dimensions
320 mm (W) x 106 mm (H) x 236 mm (D)
320
236
106
Unit: mm
Timing chart
Supported timing for PC (including DVI-I) input
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel
Frequency
(MHz)
Resolution
Mode
720 x 400
37.927
*31.469
37.861
37.500
43.269
37.879
48.077
46.875
53.674
48.363
56.476
60.023
68.667
63.981
15.73
31.47
45.00
28.13
15.63
31.25
37.50
28.13
85.039
*59.940
72.809
75.000
85.008
60.317
72.188
75.000
85.061
60.004
70.069
75.029
84.997
60.020
59.94 (interlaced)
59.94
35.500
*25.175
31.500
31.500
36.000
40.000
50.000
49.500
56.250
65.000
75.000
78.750
94.500
108.000
13.50
27.00
74.25
74.25
13.50
27.00
74.25
74.25
720 x 400_85
*VGA_60
VGA_72
VGA_75
VGA_85
SVGA_60
SVGA_72
SVGA_75
SVGA_85
XGA_60
XGA_70
XGA_75
XGA_85
SXGA_60
480i
480p
720p
1080i (1125L)
576i
576p
720p
1080i (1125L)
640 x 480
800 x 600
1024 x 768
1280 x 1024
**720 x 480
**720 x 480
**1280 x 720
**1920 x 1080
**720 x 576
**720 x 576
**1280 x 720
**1920 x 1080
59.94
59.94
50 (interlaced)
50
50
50
* denotes the timing is not available when Analog RGB or DVI-A input signal is selected
** denotes the timing is not available when DVI-D input signal is selected
58
Specifications
Download from Www.Somanuals.com. All Manuals Search And Download.
Supported timing for Component-YPbPr input
Horizontal Frequency
(kHz)
Vertical Frequency
(Hz)
Signal Format
480i(525i)@60Hz
15.73
31.47
15.63
31.25
45.00
37.50
33.75
28.13
59.94
59.94
50.00
50.00
60.00
50.00
60.00
50.00
480p(525p)@60Hz
576i(625i)@50Hz
576p(625p)@50Hz
720p(750p)@60Hz
720p(750p)@50Hz
1080i(1125i)@60Hz
1080i(1125i)@50Hz
Supported timing for Video and S-Video inputs
Horizontal
Frequency (kHz) Frequency (Hz)
Vertical
Color Sub-carrier
Frequency (MHz)
Video mode
NTSC
PAL
15.73
15.63
15.63
15.73
15.63
15.73
15.73
60
50
50
60
50
60
60
3.58
4.43
4.25 or 4.41
3.58
SECAM
PAL-M
PAL-N
PAL-60
NTSC4.43
3.58
4.43
4.43
Specifications
Download from Www.Somanuals.com. All Manuals Search And Download.
59
Warranty
Limited Warranty
BenQ warrants this product against any defects in material and workmanship, under normal
usage and storage.
Proof of purchase date will be required with any warranty claim. In the event this product is
found to be defective within the warranty period, BenQ's only obligation and your exclusive
remedy shall be replacement of any defective parts (labor included). To obtain warranty
service, immediately notify the dealer from which you purchased the product of any defects.
Important: The above warranty shall be void if the customer fails to operate the product in
accordance with BenQ's written instructions, especially the ambient humidity must be in-
between 10% and 90%, temperature in-between 0°C and 40°C, altitude lower than 10000
feet, and avoiding to operate the projector in a dusty environment. This warranty gives you
specific legal rights, and you may have other rights which vary from country to country.
For other information, please visit support.BenQ.com.
60
Warranty
Download from Www.Somanuals.com. All Manuals Search And Download.
Regulation Statements
FCC statement
CLASS B: This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
—
—
—
Reorient or relocate the receiving antenna.
Increase the distance between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
—
Consult the dealer or an experienced radio/TV technician for help.
EEC statement
This machine was tested against the 89/336/EEC (European Economic Community) for
EMC (Electronic Magnetic Compatibility) and fulfills these requirements.
MIC statement
B class equipment (Household purpose info/telecommunications equipment)
As this equipment has undergone EMC registration for household purpose, this product can
be used in any area including residential area.
WEEE directive
Disposal of Waste Electrical and Electronic Equipment by users in private households
in the European Union.
This symbol on the product or on the packaging indicates that this can
not be disposed of as household waste. You must dispose of your waste
equipment by handling it over to the applicable take-back scheme for the
recycling of electrical and electronic equipment. For more information
about recycling of this equipment, please contact your city office, the shop
where you purchased the equipment or your household waste disposal
service. The recycling of materials will help to conserve natural resources
and ensure that it is recycled in a manner that protects human health and
environment.
Regulation Statements
Download from Www.Somanuals.com. All Manuals Search And Download.
61
|