INTRODUCTION
Ins tallation
Thank you for purchasing a Belkin Uninterruptible Power Supply
(UPS). Each year, several natural and man made occurrences put
the power supplied to your electronics in your home or office in
jeopardy. At risk are your hardware, software and data because of
these power problems.
Note!
Before installation, please inspect the UPS Upon receipt.
Make sure that the UPS is not damaged.
Connect to AC Utility Power
Connect the AC inlet to utility power via the power cord.
Check whether the Site Wiring Fault indicator is lit or not. I
so, please check the utility wiring.
FOR MODELS
F6C800-UNV
F6C100-UNV
F6C120-UNV
IMPORTANT SAFETY INSTRUCTIONS
Pleas e s ave this manual!
It contains important operating instructions and warranty
information pertaining to your UPS.
Charging the Battery
Pleas e s ave or recycle the packaging materials !
For best results, charge the battery for 6 hours prior to initial use. The
UPS must be turned on to charge. The UPS charges its battery
whenever it is connected to the utility power. Should you see the red
battery light come on, the battery may need immediate charging.
The UPS packaging was designed with great care to provide
protection during shipment and delivery. These materials are
invaluable if you ever have to return the UPS for service. Damage
sustained during transit is not covered under the warranty.
Plug in Power Devices
Federal Communications Commis s ion Interference Statement
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. To assure continued compliance, use only
shielded interface cables when connecting to computer or
peripheral devices. Any changes or modifications not expressly
approved by the party responsible for compliance could void the
user’s authority to operate this equipment.
Plug your devices into the AC outlets on the top of the UPS. To use the
UPS as a master on/off switch, make sure all of the loads are switched
on.
Caution: Never connect a las er printer or s canner
to the backup outlets of UPS with other computer
equipment. A las er printer or s canner draws
s ignificantly more power when in us e than when
idle. This may overload the UPS.
ALARMS
Battery BACK UP (Slow Alarm)
When in the UPS is in battery BACK-UP mode, the On Battery (Yellow
LED) illuminates and the UPS sounds an audible alarm. The alarm stops
when the UPS returns to normal ON LINE operation.
Low Battery (Rapid Alarm)
Laser Printer
When the UPS is in battery BACK-UP mode and the battery energy
begins to run low, the UPS will beep rapidly until it shuts down from a
depleted battery or returns to ON LINE normal operation.
Turning on the UPS
Turn on your UPS by pressing and holding the On/Off/Test button for
approximately 3 seconds until the “ON LINE” Green comes on. The
CONTENTS
You should have received the following:
1 – UPS unit
1 – Bulldog Plus Shutdown Software
1 – USB Cable
1 – Serial Cable
UPS will perform a self-test each time the UPS is switched on.
OVERLOAD (Continuous alarm)
Note! The UPS maintains the battery charge when in the off
pos ition and will res pond to commands received through the
computer interface port.
When the UPS is overloaded (the connected loads exceed the maximum
rated capacity), the UPS emits a continuous alarm to warn of an overload
condition. Disconnect nonessential equipment.
from the UPS to eliminate the overload.
Turning off the UPS
1 – Phone Line Cable
FAULT (10 Seconds Continuous ly)
Turn off the UPS by pressing and holding the On/Off/Test button for
UPS FEATURES AND FUNCTIONS
Before installation, please inspect the UPS upon receipt. Make
sure that nothing is damaged.
When the output is shorted, the UPS emits a 10 seconds continuous
alarm to warn of a short condition. Disconnect the equipment from the
UPS prior to checking the equipment.
more than 3 seconds until the “ON LINE” or “ON BATTERY” LED goes
off.
Rear Panel
To Conduct a Self Tes t
Use the self-test to verify both the operation of the UPS and the
condition of the battery. In normal utility power, push the On/Off/Test
button less than 2 seconds and the UPS performs a self-test function.
Internet/
Interface Port
Phone/ Fax/
(RS232 Port)
ON LINE
DSL and
Network
During the self-test, the UPS operates in back-up mode.
ON BATTERY
Site Wiring
Protection
Fault Indicator
Note! During the s elf-tes t, the UPS briefly operates on- battery
backup power (the on-battery LED comes on). If the UPS pas s es
the s elf -tes t, it returns to on-line operation. If the UPS fails the
s elf-tes t, it immediately returns to on-line operation and lights the
replace battery LED. The loads are not affected. Recharge the
battery overnight and perform the s elf- tes t again. If the replace
battery LED is s till on, the battery will need to be replaced.
Interface Port
(USB¡@Port)
FAULT /
* OVERLOAD /
* REPLACE
BATTERY
Battery Back
up outlets
AC Input
Breaker
ON / OFF / TEST
To Silence Audible Alarm
Surge-only
Protected
Outlets
While in battery BACK-UP mode, push on/off/test button less than 2
seconds to silence the audible alarm. (This does not work if the UPS is
under LOW BATTERY or OVERLOAD condition.
AC Input
Power Cord
Your UPS features 3 LED indicators which specify’s certain
functions on your UPS. Please review the Front Panel diagram
and with this chart, as it will assist you in the use of your UPS.
All equipment must be turned off prior to hardware installation.
INTERNET/PHONE/FAX/DSL/NETWORK PROTECTION
The internet/phone/fax/DSL/network lines are surge protected and provide
complete safety for line connection.
Meaning
Connect the phone/fax/modem/network lines
Indicator
Condition
Connect a single Internet/ phone/ fax/ DSL/network line into the surge-
protected sockets on the back of the UPS. The RJ-11/RJ-45 modular
sockets accepts standard single line telephone connections. The
connection will require another length of telephone cable, which is
supplied.
AC Power is on
AVR is active
_ Solid Green
ON LINE
(Green LED)
_ Flashing Green
INTERFACE PORTS
This condition for the On-
Battery LED can indicate 1
of 2 problems:
The UPS provides both a USB and RS232 port for you use with your
computer. NOTE: Choos e one port only.
1. The UPS is on battery
backup and an
intermittent audible alarm
is on. The UPS will begin
shutdown procedure.
BATTERY BACK UP OUTLETs
_ Flashing Yellow
LED with Audible
Alarm (Beeping)
IN
OUT
Only data sensitive equipment such as a computer, monitor and external
drive should be plugged into these outlets. Battery power is automatically
provided in case of a power outage. Power (AC or battery) is not supplied
to these outlets when the UPS is switched off. (Do not plug surge
protectors or power strips into the battery back up outlets).
ON BATTERY
(Yellow LED)
Phone
Telephone
Socket
2. Bat te r y is lo w. T he UPS
will sta rt sh ut d own. T he
b uzze r sou n ds a n a ud ible
a la rm .
Modem/ Fax
Note! This connection is optional but highly suggested as Internet/
phone/ fax/modem/ DSL/network lines often carry dangerous surges
and spikes. The UPS works properly without a phone/ fax/ modem /
DSL connection.
SURGE-ONLY PROTECTED OUTLETS
The Fault/Overload can
indicate 1 of 2 problems.
1. There is a problem with
the UPS. The LED will
be lit continuously, and
the unit will sound an
audible alarm for 10
seconds.
Equipment such as a printer, fax machine, scanner, or a desk lamp can be
plugged into these outlets. These outlets do not provide power during a
power outage. These outlets are always on (when AC power is available)
& are not controlled by the front panel switch.
Caution! The Internet/ phone/ fax/modem/ DSL/network protection
feature could be rendered inoperable if improperly installed. Make sure
that the telephone line from the wall is plugged into the connector
marked “IN”, and the device to be protected is plugged into the connect
or marked “ OUT”.
_ Solid Red
FAULT/
*OVERLOAD/
*Replace
AC INPUT BREAKER (CIRCUIT BREAKER)
The circuit breaker button will be triggered if an overload condition forces
the UPS to disconnect itself from utility power. If the button sticks out,
disconnect nonessential equipment and depress breaker.
2. Battery is weak or bad,
the battery needs to be
replaced.
Battery
Serial or USB Communication Port (Ins tallation Optional)
To fully utilize the Bulldog Shutdown Software; you will need to connect
the UPS to your computer.
Battery output is drawing
more power than the UPS
can provide.
SITE WIRING FAULT INDICATOR
The Site Wiring Fault LED will illuminate when one of the following
conditions exist:
_ Flashing RED
The communication port will provide the following features:
1. Monitoring charger status
SITE WIRING
FAULT
There is either no ground
circuit or a reversed
polarity in the building
wiring.
1. Open or high-resistance ground
2. Hot and neutral polarity reversal
3. Overloaded neutral circuit
2. Monitoring UPS status
_ Solid Red
3. Monitoring battery status and condition
4. Monitoring the utility status
(ON REAR
PANEL)
5. Use the ON/OFF/TEST UPS power switch function to schedule
6. UPS for power saving
Sys tem Requirements
The UPS can be used without the software and can be used with any
computer using upto a 21” monitor or a flat panel screen. Also, you do not
have to have the software installed to utilize the battery backup outlets.
You may connect the UPS to your computer by choosing either the
Serial or USB ports. Note: Choos e one port only. Do not connect
your computer through both ports .
To fully utilize the UPS and its software, your computer must be able to
operate the following operating systems: 95/98/ME/NT4/2000/XP & Novell
3.X & Higher and have a Serial or USB port.
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTACT US
Belkin Components, Ltd
501 West Walnut St.
Compton, CA • 90220-5221
USA
Tel: 310.898.1100
Fax: 310.898.1111
Belkin Components, Ltd
Unit 13 • Gatelodge Close •
Round Spinney
Northampton, NN3 8RX UK
Tel: +44 (0) 1604678300 • Fax:
+44 (0) 1604678330
Belkin Components B.V.
Starparc Building
Belkin Australia Ltd
7 Bowen Cresent
Boeing Avenue 333
1119 PH Schiphol-Rijk
The Netherlands
West Gosford, NSW 2250
Tel: +61 (02) 4325 4666
Fax: +61 (02) 4325 4277
Tel: +31 (0) 20 654 73 00
Fax: +31 (0) 20 654 73 49
Please visit www.Belkin.com for battery replacement information.
TROUBLE SHOOTING
PROBLEM
POSSIBLE CAUSE
On/ Off /Te st but ton not
pushed or pushed less
than 3 second
SOLUTION
Press the On/Off /Test
button for more than 3
seconds
Recharge the UPS at
least four hours
Con tact service
per sonne l
UPS not on,
LED not lit
Battery voltage is too low
UPS fault
Re-plug the power
cord
Power cord loose
UPS always
on battery
mode
AC breaker is burned out Replace or reset the
or tripped
breaker
Ac utility voltage is too
high or too low, or black
out
Normal condition
Recharge the UPS at
least four hours
Battery not fully charged
Remove some un-
necessary loads
Back up
time too
s hort
UPS is overload
Charger fault or other
reason
Rep lace bat tery.
Con tact belkin.com
The UPS
continuous Overload
ly beeps
Rem ove t he non-critical
loa ds
Rep lace batte ry.
Con tact belkin.com
Red LED lit Battery failure
Download from Www.Somanuals.com. All Manuals Search And Download.
|