WHAT YOU WILL SEE AND HEAR WITH THIS ALARM
WHERE THIS ALARM SHOULD NOT BE INSTALLED
IMPORTANT! PLEASE READ CAREFULLY AND SAVE.
OPTIONAL LOCKING FEATURES
The optional locking features are designed to prevent unauthorized removal of the batteries or alarm. It is not necessary to activate the locks
in single-family households where unauthorized battery or Alarm removal is not a concern.
These Alarms have two separate locking features: one to lock the battery compartment, and the other to lock the
Alarm to the mounting bracket. You can choose to use either feature independently, or use them both.
Do NOT locate this Smoke/CO Alarm:
USER’S MANUAL
This user’s manual contains important information about your
Combination Carbon Monoxide & Smoke Alarm’s operation. If you are
installing this Alarm for use by others, you must leave this manual—or
a copy of it—with the end user.
Under Normal Operations
•
In garages, furnace rooms, crawl spaces and unfinished attics. Avoid
extremely dusty, dirty or greasy areas.
Voice: Silent
Power/Smoke LED: Flashes Green
once a minute
ONELINK® TALKING COMBINATION
SMOKE/CARBON MONOXIDE ALARM WITH
PROGRAMMABLE LOCATION
•
Where combustion particles are produced. Combustion particles
form when something burns. Areas to avoid include poorly ventilated
kitchens, garages, and furnace rooms. Keep units at least 20 feet
(6 meters) from the sources of combustion particles (stove, furnace,
water heater, space heater) if possible. In areas where a 20-foot
(6 meter) distance is not possible – in modular, mobile, or smaller
homes, for example – it is recommended the Smoke Alarm be
placed as far from these fuel-burning sources as possible. The
placement recommendations are intended to keep these Alarms at
a reasonable distance from a fuel-burning source, and thus reduce
“unwanted” alarms. Unwanted alarms can occur if a Smoke Alarm is
placed directly next to a fuel-burning source. Ventilate these areas
as much as possible.
Horn: Silent
CO LED: Off
When You Test the Alarm
Tools you will need: • Needle-nose pliers • Standard flathead screwdriver.
Both locking features use locking pins, which are molded into the mounting bracket. Depending on which locking
features you use, remove one or both pins from the mounting bracket using needle-nose pliers.
Voice: “Testing.” Horn: 3 beeps, pause, 3 beeps; Voice: “Warning,
evacuate smoke in [Location, example: “Basement”].
Evacuate.”
Smoke LED: Flashes Red in sync with the horn pattern
Horn: 4 fast beeps, pause, 4 fast beeps;
Voice: “Warning, evacuate carbon monoxide in [Location, example:
“Basement”]. Evacuate.” Pause. “Highest carbon monoxide
level was [CO level example: _0_ ppm]”.
FIRE SAFETY TIPS
Features:
Follow safety rules and prevent hazardous situations: 1) Use smoking
materials properly. Never smoke in bed. 2) Keep matches or lighters
away from children; 3) Store flammable materials in proper containers;
4) Keep electrical appliances in good condition and don’t overload
electrical circuits; 5) Keep stoves, barbecue grills, fireplaces and
chimneys grease- and debris-free; 6) Never leave anything cooking on
the stove unattended; 7) Keep portable heaters and open flames, like
candles, away from flammable materials;8) Don’t let rubbish accumulate.
•
Separate sensors to detect
smoke and CO; the two
alarm sensors work
independently
To permanently remove either locking pin, insert a flathead screwdriver between the locking pin and the
lock, and pry the pin out of the lock.
•
•
Voice with programmable
location
Separate audible and visual
signals to indicate alarm
levels of smoke or CO
CO LED: Flashes Red in sync with the horn pattern
TO LOCK THE BATTERY COMPARTMENT
TO UNLOCK THE BATTERY COMPARTMENT
Keep alarms clean, and test them weekly. Replace alarms immediately
if they are not working properly. Smoke Alarms that do not work cannot
alert you to a fire. Keep at least one working fire extinguisher on every
floor, and an additional one in the kitchen. Have fire escape ladders or
other reliable means of escape from an upper floor in case stairs are
blocked.
•
•
Within 5 feet (1.5 meters) of any cooking appliance. In air streams
near kitchens. Air currents can draw cooking smoke into the smoke
sensor and cause unwanted alarms.
In extremely humid areas. This Alarm should be at least 10 feet
(3 meters) from a shower, sauna, humidifier, vaporizer, dishwasher,
laundry room, utility room, or other source of high humidity.
If Battery Becomes Low or is Missing
Do not lock the battery compartment until you install the
batteries and test the Alarm.
1. Remove the Alarm from the
mounting bracket. If the unit is
locked to the bracket, see the
section “To Unlock the Mounting
Bracket.”
Voice: “Replace battery in [Location, example “Kitchen”].” Repeated
•
•
Wireless interconnect
Powered by two “AA”
batteries
every 5 hours
Horn: chirps once a minute
Power/Smoke LED: Flashes Green On for 2 seconds/Off for
2 seconds. Low Battery Latch is now engaged.
CO LED: Off
If the unit does not alarm during
testing, DO NOT lock the battery
compartment! Install new batteries
and test again. If the Alarm still does
not alarm, replace it immediately.
•
Side access drawer for
easy battery replacement
2. Insert a flathead screwdriver under
the head of the locking pin, and
gently pry it out of the battery
compartment lock. (If you plan to
relock the battery compartment,
save the locking pin.)
•
•
In direct sunlight.
In turbulent air, like near ceiling fans or open windows. Blowing air
may prevent CO or smoke from reaching the sensors.
BASIC SAFETY INFORMATION
If Alarm is Not Operating Properly (MALFUNCTION SIGNAL)
UL STANDARD 217
UL STANDARD 2034
Voice: “Detector error in [Location, example “Kitchen”], please see
manual” (refer to Troubleshooting Guide).
Repeated every 5 hours.
Horn: Three rapid chirps every minute
Power/Smoke LED: Flashes approximately once a minute
CO LED: Off
Printed in Mexico
M08-0146-004 J1
03/07
• Dangers, Warnings, and Cautions alert you to important
operating instructions or to potentially hazardous situations.
Pay special attention to these items.
• This Smoke/CO Alarm is approved for use in single-family
residences.
•
In areas where temperature is colder than 40˚ F (4˚ C) or hotter than
100˚ F (38˚ C). These areas include non-airconditioned crawl spaces,
unfinished attics, uninsulated or poorly insulated ceilings, porches,
and garages.
1. Using needle-nose pliers, detach
one locking pin from the mounting
bracket.
Model SCO500
3. To relock the battery compartment,
close the battery door and reinsert
locking pin in lock.
•
•
•
In insect infested areas. Insects can clog the openings to the sensing
chamber.
Less than 12 inches (305 mm) away from fluorescent lights. Electrical
“noise” can interfere with the sensor.
2. After batteries are inserted, then
push the locking pin through the
hole near the battery door latch on
the back of the Alarm.
4. Reattach the Alarm to the mounting
bracket.
INTRODUCTION
Alarm Levels of CO are Detected
•
This combination Smoke/Carbon Monoxide Alarm has two
separate alarms. The CO Alarm is not designed to detect fire
or any other gas. It will only indicate the presence of carbon
monoxide gas at the sensor. Carbon monoxide gas may be
present in other areas. The Smoke Alarm will only indicate the
presence of smoke that reaches the sensor. The Smoke Alarm
is not designed to sense gas, heat or flames.
Thank you for choosing First Alert® for your Smoke and Carbon
Monoxide Alarm needs. You have purchased a state-of-the-art Smoke &
Carbon Monoxide Alarm designed to provide you with early warning of a
smoke and/or Carbon Monoxide danger. Key features include:
Voice: “Warning, evacuate carbon monoxide in [Location, example:
In “dead air” spaces. See “Avoiding Dead Air Spaces”.
“Kitchen”]. Evacuate.” “____ ppm.”
Horn: 4 beeps, pause, 4 beeps, voice*
Power/Smoke LED: Off
CO LED: During Alarm: Flashes Red in sync with the horn pattern.
After Alarm: Flashes Red On for 2 seconds/Off for 2
seconds. CO Alarm Latch is now engaged.
When replacing the batteries, always
test the Alarm before relocking the
battery compartment.
AVOIDING DEAD AIR SPACES
“Dead air” spaces may prevent smoke from reaching the Smoke/CO
Alarm. To avoid dead air spaces, follow installation recommendations
below.
Smoke & Carbon Monoxide Combination Alarm. One alarm protects
against two deadly household threats.
®
ONELINK Enabled. Alarm automatically communicates with other
ONELINK® enabled alarms when installed.
TO LOCK THE MOUNTING BRACKET
TO UNLOCK THE MOUNTING BRACKET
*NOTE: If unit goes into CO alarm, the regular 4 beeps-brief pause
cycle will repeat for four minutes. After four minutes, the pause will
increase to one minute.
On ceilings, install Smoke/CO Alarms as close to the center of the
ceiling as possible. If this is not possible, install the Smoke/CO Alarm at
least 4 inches (102 mm) from the wall or corner.
• This Smoke/CO Alarm cannot operate without working
batteries. Removing the batteries for any reason, or failing to
replace the batteries at the end of their service life, removes
your protection.
• NEVER ignore any alarm. See “If Your Smoke/CO Alarm
Sounds” for more information on how to respond to an alarm.
Failure to respond can result in injury or death.
• The Silence Features are for your convenience only and will
not correct a problem. See "Using the Silence Features" for
details. Always check your home for a potential problem after
any alarm. Failure to do so can result in injury or death.
• Test this Smoke/CO Alarm once a week. If the Alarm ever fails
to test correctly, have it replaced immediately! If the Alarm is
not working properly, it cannot alert you to a problem.
• This product is intended for use in ordinary indoor locations
of family living units. It is not designed to measure CO levels
in compliance with Occupational Safety and Health
Administration (OSHA) commercial or industrial standards.
Individuals with medical conditions that may make them more
sensitive to carbon monoxide may consider using warning
devices which provide audible and visual signals for carbon
monoxide concentrations under 30 ppm. For additional
information on carbon monoxide and your medical condition
contact your physician.
Exclusive Voice Warning with Location will tell you the preprogrammed
location of the initiating unit and danger detected. Programmable up to
11 locations (ex. "basement"). When alarms sounds, if programmed for
basement it will say "Warning, evacuate, smoke in basement" along with
all other installed ONELINK® Voice alarms.
Spread Spectrum Horn Tone. Lower and varying horn frequency
makes it easier for elderly with normal age related hearing loss to hear
horn. Sweeps through the 2200 – 3400 Hz range.
RF Interconnect. Reliable and secure radio frequency communication
between alarms. 915 MHz frequency with 65,000 security codes and 3
channel frequency hopping.
Single Button Test/Silence eliminates confusion. Depending on what
mode the alarm is in, pushing the button provides different functions
such as testing the alarm, silencing the alarm, re-testing the alarm when
in silence and clearing the Latching features.
Two Silence Features. Temporarily silence low battery chirp for up to
eight hours before replacing low battery or silence an unwanted alarm
for several minutes.
Two Latching Features. Alarm Latch: Easily identifies initiating alarm
even after alarm condition has subsided. Low Battery Latch: Identifies
which unit is in low battery condition.
Perfect Mount System includes a gasketless base for easy installation
and a mounting bracket that keeps the alarm secure over a wide
rotation range to allow for perfect alignment.
6 Year End of Life Timer. Every 24 hours of operation a counter stored
in memory is updated. When the count equals 6 years of true operation,
meaning actually powered-up, a malfunction chirp (triple chirp) will
sound once a minute at the time of the 45 second Power-LED flash.
1. Using needle-nose pliers, detach
one locking pin from the mounting
bracket.
1. Insert a flathead screwdriver into the
rectangular cut-out on the mounting
bracket nearest to the locking pin.
Smoke is Detected
For wall mounting (if allowed by building codes), the top edge of
Smoke/CO Alarms should be placed between 4 inches (102 mm) and
12 inches (305 mm) from the wall/ceiling line, below typical “dead air”
spaces.
Voice: “Warning, evacuate smoke in [Location, example: “Kitchen”].
Evacuate.”
2. Pry the Alarm away from the bracket
by pushing up on the screwdriver and
turning the Alarm counterclockwise
(left) at the same time.
Horn: 3 beeps, pause, 3 beeps, voice
2. Insert the locking pin through the
hole on the back of the Alarm as
shown in the diagram.
Power/Smoke LED: During Alarm: Flashes Red in sync with the
horn pattern. After Alarm: Flashes Red On for 2 seconds/
Off for 2 seconds. Smoke Alarm Latch is now engaged.
CO LED: Off
On a peaked, gabled, or cathedral ceiling, install first Smoke/CO
Alarm within 3 feet (0.9 meters) of the peak of the ceiling, measured
horizontally. Additional Smoke/CO Alarms may be required depending
on the length, angle, etc. of the ceiling's slope. Refer to NFPA 72 for
details on requirements for sloped or peaked ceilings.
3. When you attach the Alarm to the
mounting bracket, the locking pin’s
head will fit into a notch on the
bracket.
Smoke Alarm is Silenced
Voice: Silent
CO Alarm is Silenced
Voice: Silent
Horn: Off
Horn: Off
HOW TO INSTALL THIS ALARM
Power/Smoke LED: Flashes Red
CO LED: Off
Power/Smoke LED: Off
CO LED: Flashes Red
For quick installation instructions see the “Quick and Easy Guide to
Programming Your ONELINK® Alarm and Using the Optional Features”.
IF THE SMOKE ALARM SOUNDS
RESPONDING TO AN ALARM
IF YOUR SMOKE/CO ALARM SOUNDS
WHAT TO DO FIRST–IDENTIFY THE TYPE OF
ALARM SIGNAL
Refer to previous section “What You Will See and Hear With This
Alarm”.
This combination Smoke/CO Alarm was designed to be mounted
on the ceiling or wall. It is not a tabletop device. You must install this
device on the ceiling or wall as outlined below. Read “Where To Install
This Alarm” before starting.
INSTALLATION
WHERE TO INSTALL THIS ALARM
Minimum coverage for Smoke Alarms, as recommended by the
National Fire Protection Association (NFPA), is one Smoke Alarm on
every floor, in every sleeping area, and in every bedroom (See
“Regulatory Information For Smoke Alarms” for details on the NFPA
recommendations).
•
•
If the unit alarms and you are not testing the unit, it is warning
you of a potentially dangerous situation that requires your
immediate attention. NEVER ignore any alarm. Ignoring the
alarm may result in injury or death.
Never remove the batteries from a battery operated Smoke/CO
Alarm to stop an unwanted alarm (caused by cooking smoke,
etc.). Removing batteries disables the alarm so it cannot sense
smoke, and removes your protection. Instead open a window
or fan the smoke away from the unit. The alarm will reset auto-
matically.
PARTS OF THIS SMOKE/CO ALARM
IF THE CO ALARM SOUNDS
STEP BY STEP GUIDE TO PROGRAMMING
THIS ALARM
1
2
3
4
Test/Silence Button
Battery Compartment
Power/Smoke Alarm LED
CO Alarm LED
“ALARM-MOVE TO FRESH AIR”
For CO Alarms, the National Fire Protection Association (NFPA)
recommends that a CO Alarm should be centrally located outside of
each separate sleeping area in the immediate vicinity of the bedrooms.
For added protection, install additional CO Alarms in each separate
bedroom, and on every level of your home.
If you hear the CO alarm horn and the CO red light is flashing,
FOR FIRST TIME AND WHEN CHANGING BATTERIES
move everyone to a source of fresh air.
© 2007 BRK Brands, Inc., a subsidiary of Jarden Corporation.
3901 Liberty Street Road, Aurora, IL 60504-8122
All rights reserved.
DO NOT remove the batteries!
Action:
Alarm Will Say:
•
If the unit alarms get everyone out of the house immediately.
1. Insert batteries (2, AA batteries).
“Welcome, First Alert Smoke and
Carbon Monoxide Alarm.”
Consumer Affairs: (800) 323-9005 • www.firstalert.com
NOTE: For added protection, install an additional Smoke/CO Alarm at least
15 feet (4.6 meters) away from the furnace or fuel burning heat source
where possible. In smaller homes or in manufactured homes where this
distance cannot be maintained, install the Alarm as far away as possible
from the furnace or other fuel burning source. Installing the Alarm closer
than 15 feet (4.6 meters) will not harm the Alarm, but may increase the
frequency of unwanted alarms.
WHAT TO DO IN CASE OF FIRE
Actuation of your CO Alarm indicates the presence of carbon
monoxide (CO) which can kill you. In other words, when your CO
Alarm sounds, you must not ignore it!
“No location programmed” if first
time or “[Location, example:
“Basement”] location programmed”
when changing batteries.
“To select location, press and hold
test button now.”
Tools you will need: pencil, drill with 3/16” or 5mm drill bit,
Phillips screwdriver, hammer.
®
• Don’t panic; stay calm. Follow your family escape plan.
All First Alert Smoke Alarms conform to regulatory requirements,
including UL217 and are designed to detect particles of combustion.
Smoke particles of varying number and size are produced in all fires.
• Get out of the house as quickly as possible. Don’t stop to get
dressed or collect anything.
IF THE CO ALARM SIGNAL SOUNDS:
1. Operate the Test/Silence button.
•
Do not install this unit over an electrical junction box. Air
currents around junction boxes can prevent smoke from
reaching the sensing chamber and prevent the unit from
alarming. Only AC powered units are intended for installation
over junction boxes.
Ionization technology is generally more sensitive than photoelectric
technology at detecting small particles, which tend to be produced
in greater amounts by flaming fires, which consume combustible
materials rapidly and spread quickly. Sources of these fires may include
paper burning in a wastebasket, or a grease fire in the kitchen.
Photoelectric technology is generally more sensitive than ionization
technology at detecting large particles, which tend to be produced
in greater amounts by smoldering fires, which may smolder for hours
before bursting into flame. Sources of these fires may include cigarettes
burning in couches or bedding.
• Feel doors with the back of your hand before opening them.
If a door is cool, open it slowly. Don’t open a hot door. Keep doors
and windows closed, unless you must escape through them.
2. Call your emergency services, fire department or 911. Write down the
number of your local emergency service here:
In general, install combination Smoke and Carbon Monoxide Alarms:
2. Press & Hold Test Button if
you would like to program the
location or change the location
of the Alarm. Release button
after Alarm responds.
“To save location, press and hold
test button after location is heard.”
Alarm will speak list of locations
(see below).
•
In the hall near every sleeping area. If your home has multiple
sleeping areas, install a unit in each. If a hall is more than 40 feet
(12 meters) long, install a unit at each end.
• Cover your nose and mouth with a cloth (preferably damp).
Take short, shallow breaths.
____________________________________________________________
• Meet at your planned meeting place outside your home, and
do a head count to make sure everybody got out safely.
3. Immediately move to fresh air—outdoors or by an open door or
window. Do a head count to check that all persons are accounted
for. Do not re-enter the premises, or move away from the open door
or window until the emergency services responder has arrived, the
premises have been aired out, and your CO Alarm remains in its
normal condition.
If you want to lock the battery compartment, or lock the Smoke/CO
Alarm to the mounting bracket, please read the “Optional Locking
Features” section in the “Quick and Easy Guide to Programming
•
•
On every level of your home, including finished attics and basements.
Inside every bedroom, especially if people sleep with the door partly
or completely closed.
• Call the Fire Department as soon as possible from outside.
Give your address, then your name.
3. After you hear the location of
where you are placing the Alarm,
Press & Hold the Test Button.
“[Location, example: “Basement”]
location saved.”
If no location is chosen:
“No location saved.”
®
Your ONELINK Alarm and Using the Optional Features” attachment
For maximum protection, use both types of Smoke Alarms on
each level and in every bedroom of your home.
•
•
•
At the top of first-to-second floor stairs.
At the bottom of the basement stairs.
For additional coverage, install Alarms in all rooms, halls, and storage
areas, where temperatures normally remain between 40˚ F and 100˚F
(4˚ C and 38˚ C).
before you begin installation.
• Never go back inside a burning building for any reason.
1. Hold the mounting bracket against the ceiling (or wall) so the vertical
mounting slot is aligned in the 12 o’clock position and trace around
the inside of the mounting slots (vertical and horizontal mounting).
• Contact your Fire Department for ideas on making your home
safer.
4. After following steps 1-3, if your CO Alarm reactivates within a
24-hour period, repeat steps 1-3 and call a qualified appliance tech-
nician to investigate for sources of CO from fuel-burning equipment
and appliances, and inspect for proper operation of this equipment.
If problems are identified during this inspection have the equipment
serviced immediately. Note any combustion equipment not inspected
by the technician, and consult the manufacturers’ instructions, or
contact the manufacturers directly, for more information about CO
safety and this equipment. Make sure that motor vehicles are not,
and have not, been operating in an attached garage or adjacent
to the residence. Write down the number of a qualified appliance
technician here:
Your Alarm has now been programmed for the location of your choice.
Available locations:
WIRELESS OPERATION
First Alert® ONELINK® Technology is the easy, cost-effective way to
provide your family with whole-home safety. All ONELINK® Alarms
communicate with each other without wires or connectors. When one
Alarm sounds, they all sound. This provides your family with an earlier
warning of potential danger, and gives you more time to react.
The communication distance (range) between any two ONELINK® Alarms
is typically 50 feet (15 meters) inside of a home. Some features of a
home, such as the number of floors, number/size of rooms, furniture and
types of building materials used may reduce the range of the Alarms.
Examples include: suspended ceilings, ductwork, large metallic appli-
ances (refrigerators) and metal studs. A feature of ONELINK® Alarms is
that they operate as a mesh network. All Alarms will repeat any alarm
signal that is received to all other ONELINK® Alarms. Interference from
structural conditions can be overcome by adding additional Alarms to
route the wireless signal around obstructions.
Basement
Living Room
Family Room
Office
Kitchen
Child’s Bedroom
Master Bedroom
Guest Bedroom
Utility Room
2. Put the unit where it won’t get covered with dust when you drill the
mounting holes.
Alarms have various limitations. See "General Limitations of
Smoke/CO Alarms" for details.
SUGGESTED AREAS FOR INSTALLING
SMOKE ALARMS, CO ALARMS, AND COMBO UNITS
Dining Room
No Location
Hallway
3. Using a 3/16” (5 mm) drill bit, drill a hole through the center of the
oval outlines you traced.
KEY:
USING THE SILENCE FEATURES
4. Insert the plastic screw anchors (in the plastic bag with screws) into
the holes. Tap the screw anchors gently with a hammer, if necessary,
until they are flush with the ceiling or wall.
SMOKE ALARMS
®
SMOKE ALARM WITH
SILENCE FEATURE
ADDING AND LINKING ADDITIONAL ONELINK
ALARMS
NOTE: Steps 1 through 3 need to be completed within two minutes.
If more than two minutes pass, the Green power LED will stop
blinking. Simply open the battery drawer of the second Alarm and
repeat steps 1 through 3.
1. Insert the batteries into the
battery drawer of the next
Alarm. DO NOT CLOSE THE
DRAWER.
Never remove the batteries to quiet an unwanted alarm. Removing
the batteries disables the alarm and removes your protection.
5. Line the mounting bracket up over the plastic screw anchors.
CO ALARMS
____________________________________________________________
The Silence Feature is intended to temporarily silence the horn while
you identify and correct the problem. Do not use the Silence Feature in
emergency situations. It will not correct a CO problem or extinguish a
fire.
6. Screw the mounting bracket to the ceiling or wall through the
mounting slots using the two screws provided.
BOTH, OR COMBINATION
SMOKE/CO ALARMS
Suggested locations are based on
NFPA recommendations (NFPA 72
for Smoke Alarms and NFPA 720 for
Carbon Monoxide Alarms). Always
refer to national and local codes
AFTER AN ALARM
7. Attach the Smoke/CO Alarm to the
mounting bracket. Line up the guides
on the alarm’s base with the guides
on the mounting bracket. When guides
are lined up, turn the base clockwise
(right) until it snaps into place.
After the emergency responders arrive, the premises aired out, and
your CO Alarm remains in its normal condition, you can check what
the highest carbon monoxide level sensed was:
The Silence Feature can temporarily quiet an unwanted alarm for several
minutes. You can silence this Smoke/CO Alarm by pressing the
Test/Silence button on the alarm cover for at least 3-5 seconds.
before beginning any installation.
In new construction AC and AC/DC smoke alarms MUST
be interconnected to meet NFPA recommendations.
•
The range and proper operation of any wireless device will
vary depending on its surroundings. It is very important that
each Alarm is tested individually before and after installation
to make sure that all Alarms respond properly.
The ONELINK Alarms are not to be used outdoors or to
transmit between buildings. The Alarms will not communicate
properly under these conditions.
Metal objects and metallic wallpaper may interfere with
signals from wireless Alarms. Alarms should be tested after
changes to your home such as remodeling, moving furniture,
and with metal doors opened and closed.
After the Test/Silence button is released, the Red LED blinks during the
silence mode.
Action:
1. Press & Hold Test Button
Alarm Will Say:
“Highest carbon monoxide level
was ___ ppm. Please see manual.”
“To clear highest carbon monoxide
level, press and hold test button
now.”
2. Press and hold the test
button and then close the
battery drawer.
NOTE: Once the Alarm is snapped
onto the mounting bracket, you
can rotate the Alarm to adjust the
alignment.
Recommended Placement
When the Smoke Alarm
is Silenced
When the CO Alarm
is Silenced
•
When installing on the wall, the top edge of Smoke Alarms should
be placed between 4 inches (102 mm) and 12 inches (305 mm) from
the wall/ceiling line.
®
•
•
3. Once you hear the unit chirp,
release the test button.
The Smoke Alarm will remain
silent for up to 15 minutes, then
return to normal operation.
The CO Alarm will remain silent
for up to 4 minutes.
8. Test the Smoke/CO Alarm.
See “Weekly Testing” for details.
The Green power LED will start to blink indicating the ONELINK®
Alarm is waiting for program data from one of the other setup
ONELINK® Alarms.
•
•
When installing on the ceiling, place the Alarm as close to the center
as possible.
2. Press & Hold Test Button, if you
would like to clear the highest
level sensed.
If you would like to keep the
highest level in memory, do not
press anything.
“Highest carbon monoxide level
cleared.”
After 4 minutes, if CO levels
remain potentially dangerous the
horn will start sounding again.
In either case, install at least 4 inches (102 mm) from where the
wall and ceiling meet. See “Avoiding Dead Air Spaces” for more
information.
If the smoke has not cleared–or
continues to increase–the device
will go back into alarm.
4. Press and hold the test button on the first Alarm, until the second
Alarm chirps and its Green power LED stops blinking. Then release
the test button.
5. If you have purchased the hardwired battery back-up ONELINK®
Alarm, you can now connect the hardwired Alarm by installing the
three-wire connector on the ceiling to the Alarm.
Alarm will say nothing.
Your First Alert® ONELINK® Smoke/CO Alarm will automatically commu-
nicate both potential fires and carbon monoxide presence with all other
First Alert® ONELINK® Smoke/CO Alarms.
NOTE: For any location, make sure no door or other obstruction could
keep carbon monoxide or smoke from reaching the Alarm.
FCC NOTICE: This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired
operation. FCC ID: M7U5001L
Installing Smoke/CO Alarms in Mobile Homes
For minimum security install one Smoke/CO Alarm as close to each
sleeping area as possible. For more security, put one unit in each room.
Many older mobile homes (especially those built before 1978) have little
or no insulation. If your mobile home is not well insulated, or if you are
unsure of the amount of insulation, it is important to install units on
inside walls only.
6. Repeat steps 1-5 for additional ONELINK® Alarms.
®
You have now successfully linked your new ONELINK Alarms. To
add additional Alarms at a later time, follow steps 1 through 5.
Changes or modifications not expressly approved by BRK Brands,
Inc. could void the user’s authority to operate the equipment.
1
2
3
4
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.
OPTIONAL LOCKING FEATURES
The optional locking features are designed to discourage unauthorized removal
of the batteries or alarm. It is not necessary to activate the locks in single-family
households where unauthorized battery or alarm removal is not a concern.
All Alarms Respond as One
This Smoke/CO Alarm has two separate locking features: one to lock the battery
compartment, and the other to lock the Smoke/CO Alarm to the mounting bracket.
You can choose to use either feature independently, or use them both.
QUICK AND EASY GUIDE TO PROGRAMMING
TM
YOUR ONELINK ALARM AND
USING THE OPTIONAL FEATURES
Tools you will need: • Needle-nose pliers • Standard flathead screwdriver.
Both locking features use locking pins, which are
molded into the mounting bracket. Depending on
which locking features you use, remove one or
both pins from the mounting bracket using needle-
nose pliers.
M08-0147-000
O
04/05
MODEL SCO500
Printed in Mexico
All Rights Reserved. © 2005 BRK Brands, Inc.
BRK Brands, Inc., 3901 Liberty Street Road, Aurora, IL 60504-8122
Consumer Affairs: (800) 323-9005 • www.firstalert.com
To permanently remove either locking pin, insert
a flathead screwdriver between the locking pin
and the lock, and pry the pin out of the lock.
QUICK INSTALLATION INSTRUCTIONS
1. Insert two (2) AA batteries into the battery drawer of the first Alarm and close the
drawer.
2. The Alarm will sound with a chirp.
TO LOCK THE BATTERY COMPARTMENT
Do not lock the battery compartment until you install the batteries and test the
Smoke/CO Alarm.
3. You will now be prompted to set the Alarm's location. Follow the direction given
by the Alarm.
Available locations:
1. Install the batteries before attaching the Alarm to the
bracket. Insert the two (2) AA batteries (included) into the
battery compartment. Match the terminals on the end of
the battery with the terminals on the unit. Match “+” to “+”
and “-” to “-.”
Basement
Living Room
Family Room
Office
Kitchen
Child’s Bedroom
Master Bedroom
Guest Bedroom
Utility Room
Dining Room
No Location
Hallway
Your Alarm has now been programmed for the location of your choice.
If the batteries are not fully inserted, the unit cannot receive
battery power.
NOTE: Steps 4 through 6 need to be completed within two minutes. If more
than two minutes pass, the Green power LED will stop blinking. Simply open
the battery drawer of the second Alarm and repeat steps 4 through 6.
2. Push and hold test button until the alarm sounds.
4. Insert the batteries into the battery drawer of the next Alarm. DO NOT CLOSE
If the unit does not alarm during testing, DO NOT lock the battery compartment!
Install new batteries and test again. If the unit still does not alarm, replace it
immediately.
3. Using needle-nose pliers, detach one locking pin from the mounting bracket.
4. Push the locking pin through the hole near the battery door latch on the back of
the Smoke/CO Alarm.
THE DRAWER.
5. Press and hold the test button and then close the battery drawer.
6. Once you hear the unit chirp, release the test button. The Green power LED will
start to blink indicating the ONELINKTM Alarm is waiting for program data from
one of the other setup ONELINKTM Alarms.
7. Press and hold the test button on the first Alarm, until the second Alarm chirps
and its Green power LED stops blinking. Then release the test button.
8. If you purchased the Talking Smoke and Carbon Monoxide Alarm, you will now be
prompted to set the Alarm's location. Follow the directions given by the Alarm.
9. If you have purchased the hardwired battery back-up ONELINKTM Alarm, you can
now connect the hardwired Alarm by installing the three-wire connector on the
ceiling to the Alarm.
10. Repeat steps 4-9 for additional ONELINKTM Alarms.
TO UNLOCK THE BATTERY COMPARTMENT
1. Remove the Smoke/CO Alarm from the mounting bracket. If the unit is locked to
the bracket, see the section “To Unlock the Mounting Bracket.”
2. Insert a flathead screwdriver under the head of the locking pin,
and gently pry it out of the battery compartment lock. (If you
plan to re-lock the battery compartment, save the locking pin.)
You have now successfully linked your new ONELINKTM Alarms.
To add additional Alarms at a later time, follow steps 4 through 9.
3. To relock the battery compartment, close the battery door and
reinsert locking pin in lock.
4. Reattach the Smoke/CO Alarm to the mounting bracket.
IF YOU ARE CHANGING THE BATTERIES
When replacing the batteries, always test the Smoke/CO Alarm before relocking
the battery compartment.
Action:
Alarm Will Say:
1. Insert batteries (2, AA batteries).
“Welcome, First Alert Carbon Monoxide
and Smoke Alarm. Location [If location
already programmed, example “Kitchen”]
programmed. To select location, press
and hold test button now.”
TO LOCK THE MOUNTING BRACKET
1. Using needle-nose pliers, detach one locking pin from the mounting bracket.
2. Insert the locking pin through the hole on the back of the Smoke/CO Alarm as
shown in the diagram.
3. When you attach the Smoke/CO Alarm to the mounting bracket, the locking pin’s
head will fit into a notch on the bracket.
2. Press & Hold Test Button if you would
like to change the location.
“To change location, press and hold test
button after location is heard.” Alarm will
speak list of locations (see below).
3. After you hear the location of where
you are placing the Alarm, Press &
Hold the Test Button.
“[Location, example “Kitchen”]
location saved.”
If no location is chosen: “No location
saved.”
TO UNLOCK THE MOUNTING BRACKET
1. Insert a flathead screwdriver into the rectangular cut-out
on the mounting bracket nearest to the locking pin.
2. Pry the Smoke/CO Alarm away from the bracket by
pushing up on the screwdriver and turning the Smoke/
CO Alarm counterclockwise (left) at the same time.
Your Alarm has now been programmed for the location of your choice.
Available locations:
Basement
Living Room
Family Room
Office
Kitchen
Child’s Bedroom
Master Bedroom
Guest Bedroom
Utility Room
Dining Room
No Location
Hallway
USING THE SILENCE FEATURES
Never remove the batteries to quiet an unwanted alarm. Removing the batteries
disables the alarm and removes your protection.
The Alarm Silence Feature can temporarily quiet an unwanted alarm for several
minutes. You can silence the Smoke/CO Alarm by pressing the Test/Silence button
on the alarm cover for at least 6 seconds.
After the Test/Silence button is released, the Alarm Voice will say “Horn silenced,
detector active.”
The Low Battery Warning Silence Feature can temporarily quiet the low battery
warning “chirp” for up to 8 hours. You can silence the low battery warning “chirp” by
pressing the Test/Silence button on the alarm cover for at least 3-5 seconds.
Once the low battery warning “chirp” silence feature is activated, the unit continues to
flash the Green light twice a minute for 8 hours. After 8 hours, the low battery “chirp”
will resume. Replace the batteries as soon as possible; this unit will not operate
without battery power!
First Alert® is a registered trademark of the First Alert Trust.
1
2
Download from Www.Somanuals.com. All Manuals Search And Download.
|