BOXLIGHT Projector XD 15c User Manual

BOXLIGHT XD-15c  
User’s Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BOXLIGHT XD-15c User’s Guide  
Table of Contents  
Table of Contents  
iii  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BOXLIGHT XD-15c User’s Guide  
INTRODUCTION  
Caution  
TO PREVENT SHOCK, DO NOT OPEN THE CABINET. NO USER –SER-  
VICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SER-  
VICE PERSONNEL. PLEASE READ THIS USER’S GUIDE BEFORE YOU  
OPERATE YOUR PROJECTOR. SAVE THIS USER’S GUIDE FOR  
FUTURE REFERENCE .  
Safety Instructions  
1. Read this user’s guide before you operate your projector and save it for future  
reference.  
2. The lamp becomes extremely hot during operation. Allow the projector to cool  
for approximately 45 minutes prior to removing the lamp assembly for  
replacement. Do not operate lamps beyond the rated lamp life. Excessive  
operation of lamps beyond the rated life could cause them to explode on rare  
occasions.  
3. Never replace lamp assembly or any electronic components unless the projector  
is unplugged.  
4. To reduce the risk of electric shock, do not disassemble this appliance. Take it to  
a qualified technician when service or repair is required. Incorrect reassembly can  
cause electric shock when the appliance is subsequently used.  
5. Do not place this product on an unstable cart, stand, or table. The product may  
fall, sustaining serious damage.  
6. This product is capable of displaying inverted images for ceiling mount  
installation. Please use suitable equipment for mounting the unit and ensure it is  
securely installed.  
Caution  
Always open the lens shutter or remove the lens cap when the projec-  
tor lamp is on.  
Do not look straight at the projector lens during operation. The intense  
light beam may damage your eyes.  
In some countries, the line voltage is NOT stable. This projector is  
designed to operate safely within a bandwidth of 110 to 240 volts, but  
could fail if power cuts or surges of ±10 volts occur. In these high-risk  
areas, it is recommended to install a power stabilizer unit to be used in  
conjuction with this projector.  
Save this user’s guide: The information contained in this manual will assist you in operat-  
ing and maintaining your personal projector.  
Introduction  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
BOXLIGHT XD-15c User’s Guide  
Warranty  
LIMITED WARRANTY  
Boxlight ("Boxlight") warrants that each XD-15c ("the Product") sold hereunder will con-  
form to and function in accordance with the written specifications of Boxlight. Said limited  
warranty shall apply only to the first person or entity that purchases the Product for per-  
sonal or business use and not for the purpose of distribution or resale. Said warranty shall  
continue for a period of two (2) years from the date of such purchase. The standard limited  
warranty excludes the lamps in projectors after 120 days and the accessories after one year.  
Boxlight does not warrant that the Product will meet the specific requirements of the first  
person or entity that purchases the Product for personal or business use. Boxlight's liability  
for the breach of the foregoing limited warranty is limited to the repair or replacement of  
the Product or refund of the purchase price of the Product, at Boxlight's sole option.  
Replacement Product may be re-furbished in "like-new" condition, at Boxlight's sole discre-  
tion. To exercise the Purchaser's rights under the foregoing warranty, the Product must be  
returned at the Purchaser's sole cost and expense, to Boxlight or to any authorized Boxlight  
service center provided, and the Product must be accompanied by a written letter explain-  
ing the problem and which includes (i) proof of date of purchase; (ii) the dealer's name; and  
(iii) the model and serial number of the Product. When sending your unit in for repair,  
please ship your unit in its original packing material or a Boxlight approved ATA Shipping  
Case, or have a professional packaging company pack the unit. Please insure your shipment  
for its full value. A return authorization number, issued by the Boxlight customer service  
department, must also be clearly displayed on the outside of the shipping carton containing  
the Product.  
WARRANTY LIMITATION AND EXCLUSION  
Boxlight shall have no further obligation under the foregoing limited warranty if the Product  
has been damaged due to abuse, misuse, neglect, accident, unusual physical or electrical  
stress (unusual physical and electrical stress includes unusually long operation, exposure to  
smoke and other airborne contaminants), unauthorized modifications, tampering, alter-  
ations, or service other than by Boxlight or its authorized agents, causes other than from  
ordinary use or failure to properly use the Product in the application for which said Product  
is intended.  
DISCLAIMER OF UNSTATED WARRANTIES  
THE WARRANTY PRINTED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THIS  
PURCHASE. ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT  
NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS  
FOR A PARTICULAR PURPOSE ARE DISCLAIMED. THERE ARE NO WARRANTIES  
THAT EXTEND BEYOND THE FACE HEREOF AND THE FOREGOING WARRANTY  
SHALL NOT BE EXTENDED, ALTERED OR VARIED EXCEPT BY WRITTEN INSTRU-  
MENT SIGNED BY BOXLIGHT. SOME STATES DO NOT ALLOW LIMITATIONS ON  
HOW LONG AN IMPLIED WARRANTY MAY LAST, SO SUCH LIMITATIONS MAY NOT  
APPLY TO YOU.  
Introduction  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
BOXLIGHT XD-15c User’s Guide  
LIMITATION OF LIABILITY  
IT IS UNDERSTOOD AND AGREED THAT BOXLIGHT'S LIABILITY WHETHER IN  
CONTRACT, IN TORT, UNDER ANY WARRANTY, IN NEGLIGENCE OR OTHER-  
WISE SHALL NOT EXCEED THE RETURN OF THE AMOUNT OF THE PURCHASE  
PRICE PAID BY PURCHASER AND UNDER NO CIRCUMSTANCES SHALL BOXLIGHT  
BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES  
OR LOST PROFITS, LOST REVENUES OR LOST SAVINGS. THE PRICE STATED FOR  
THE PRODUCT IS A CONSIDERATION IN LIMITING BOXLIGHT'S LIABILITY. NO  
ACTION, REGARDLESS OF FORM, ARISING OUT OF THE AGREEMENT TO PUR-  
CHASE THE PRODUCT MAY BE BROUGHT BY PURCHASER MORE THAN ONE  
YEAR AFTER THE CAUSE OF ACTION HAS ACCRUED. SOME STATES DO NOT  
ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL  
DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.  
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY  
ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE.  
FCC Statement  
FCC STATEMENT - CLASS A: This equipment generates, uses and can radiate radio fre-  
quency energy, and if not installed and used in accordance with the instruction manual,  
may cause interference to radio communications. It has been tested and found to comply  
with the limits for a Class “A” computing device pursuant to Subpart B of Part 15 of the  
FCC Rules, which are designed to provide reasonable protection against such interference  
when operated in a commercial environment. Operation of this equipment in a residential  
area is likely to cause interference, in which case the user at his/her own expense will be  
required to take whatever measures may be required to correct the interference.  
FCC STATEMENT - CLASS B: This equipment generates, uses and can radiate radio fre-  
quency energy and, if not installed and used in accordance with the instructions, may  
cause harmful interference to radio communications. However, there is no guarantee that  
interference will not occur in a particular installation. If this equipment does cause harm-  
ful interference to radio or television reception, which can be determined by turning the  
equipment off and on, the user is encouraged to try to correct the interference by one or  
more of the following measures:  
— Reorient or relocate the receiving antenna.  
— Increase the distance between the equipment and receiver.  
— Connect the equipment into an outlet on a circuit different from that to  
which the receiver is connected.  
— Consult the dealer or an experienced radio/TV technician for help.  
EEC STATEMENT: This machine was tested against the 89/336/EEC (European Eco-  
nomic Community) for EMC (Electro Magnetic Compatibility) and fulfills these require-  
ments.  
Introduction  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
BOXLIGHT XD-15c User’s Guide  
Shipping Contents  
The projector is shipped with the cables required for connection to standard PC or  
laptop computers. Carefully unpack and verify that you have all the items shown below.  
If any of these items are missing, please contact BOXLIGHT.  
Optional Accessories  
1. Mac adapter (switchable)  
2. Spare lamp module  
Introduction  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
BOXLIGHT XD-15c User’s Guide  
Projector Description  
Projector  
1. External control panel  
(see next page)  
9. Video connector  
10. D-sub connector  
2. Projection lens  
(for computer/ HDTV input)  
3. Front adjustment feet  
4. IR remote sensor  
5. Ventilation grill  
6. Kensington lock  
11. Audio input  
12. Rear adjustment feet  
13. Lamp access door  
(underneath unit)  
7. AC power cord input  
8. S-video connector  
12  
5
Introduction  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
BOXLIGHT XD-15c User’s Guide  
External Control Panel  
Exit  
Keystone/ Left  
Menu  
Keystone/ Right  
Power  
Auto  
Source  
Lamp status  
indicator  
The Infrared Remote Receiver (Front and Rear) allows the projector to  
accept signals from the remote control. For best results, be sure to aim the control  
toward the sensor without any obstructions between the two, and at a distance no  
greater than 6 meters (20 feet).  
Menu will display the menu system on screen. Press Menu again to access the  
sub-menus. Left and Right help you navigate among choices and settings in the  
menus and sub-menus. However, when the on screen menu is not activated, the  
Left and Right buttons will function as Keystone +/- hot keys.  
Press the Exit button to go back to the main menu. Press Exit again to leave the  
menu system.  
The Status Indicator will blink or light up when the lamp needs service, cooling  
or replacement. See “Lamp Information” on page 20 for more detailed information.  
When the projector is on, Back-lit Power will blink during warm-up and turn to  
solid green to indicate the projector is ready for use.  
Press and hold Power for 1 second to turn the projector on or off.  
Auto key: Automatically sense the best picture quality for current received signals.  
Source key: Select signal sources, PC, Video, S-video and YPbPr.  
Introduction  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
BOXLIGHT XD-15c User’s Guide  
Adjuster  
The projector is equipped with a quick-release adjuster foot and button for adjusting  
its tilt angle.  
1. Lift the projector up and press the adjuster button to release the adjuster.  
2. The adjuster will drop into position and be locked.  
Projector Features  
The projector integrates high performance optical engine projection and user-friendly  
design to deliver high reliability and ease of use.  
The Projector offers the following features:  
Compact and portable unit  
Full-function remote control  
Manual zoom lens  
One key auto-adjustment to display the best picture quality  
Easy digital keystone correction through hot keys to correct distorted images  
Adjustable color balance control for data/video  
Ultra-high brightness projection lamp  
Ability to display high quality 16.7 million colors  
On screen menus in 7 languages: English, French, German, Italian, Spanish,  
Simplified Chinese, and Traditional Chinese.  
Powerful AV function to provide high AV picture  
HDTV compatibility (YPBPR)  
Note: The brightness of your machine will vary depending on the ambient  
room conditions and contrast/brightness settings.  
Introduction  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
BOXLIGHT XD-15c User’s Guide  
Remote Control Description  
(
Remote Control Features  
The remote control sensors are located in the front/ back of the projector. The  
distance between the sensor and the remote control should not exceed 6 meters (20  
feet).  
Introduction  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
BOXLIGHT XD-15c User’s Guide  
FREEZE  
The image can be frozen when FREEZE is pressed. A “Pause” icon will appear in the  
lower right corner of the screen for three seconds. To release the freeze function,  
press the FREEZE button, RETURN button or SOURCE button (when the input  
source is switched over during display) again. A “Play” icon will appear in the lower  
right corner of the screen for three seconds when the freeze function is released.  
ZOOM IN/OUT  
By pressing ZOOM IN +, the center of the picture will be magnified. When the +  
button is pressed again, the picture is further magnified, up to four times the original  
size. By pressing ZOOM OUT -, the size of the image is reduced. When the - button  
is pressed again, the picture is further reduced until it is restored to its original size.  
To return to the normal display mode, press the RETURN button. (This function can  
be used in combination with FREEZE. )  
A
Zoom In  
Introduction  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
BOXLIGHT XD-15c User’s Guide  
Installing or Replacing Batteries  
Push and slide the battery compartment lid in the direction shown.  
Install batteries as indicated by the diagram inside the compartment.  
Position the lid over the compartment and snap it back into place.  
Caution  
Avoid excessive heat and humidity. There may be danger of an explosion if  
batteries are incorrectly replaced. Replace only with the same or equivalent  
type recommended by the manufacturer. Dispose of used batteries accord-  
ing to the manufacturer’s instructions.  
Introduction  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
BOXLIGHT XD-15c User’s Guide  
INSTALLATION  
Screen Size  
Place the projector at the required distance from the screen according to the desired  
picture size (see the table below).  
L Projection Distance  
Screen Size (Max.)  
A. Width  
(cm/in)  
Screen Size (Min.)  
B. Width  
(cm/in)  
L. Projection  
distance (cm/in)  
Diagonal  
(cm/in)  
C. Height  
(cm/in)  
Diagonal  
(cm/in)  
D. Height  
(cm/in)  
77/30.4  
61.8/24  
123.65/49  
185.3/73  
247.0/97  
308.7/122  
370.5/146  
432.2/170  
494.0/194  
555.7/219  
617.5/243  
46.3/18  
92.7/36  
100/39  
200/79  
63/24.9  
50.7/20  
101.3/40  
151.9/60  
202.5/80  
253.2/100  
303.8/120  
354.4/140  
405.1/160  
455.7/180  
506.3/200  
38.0/15  
76.0/30  
154/60.8  
232/91.2  
309/121.5  
386/151.9  
463/182.3  
541/213.1  
617/243.1  
695/273.5  
772/303.9  
127/49.9  
190/74.7  
253/99.7  
316/124.6  
380/149.5  
443/174.6  
506/199.4  
570/224.3  
633/249.2  
138.9/55  
185.2/73  
231.6/91  
277.9/109  
324.18/128  
370.5/146  
416.7/164  
463.11/182  
300/118  
400/157  
500/197  
600/236  
700/276  
800/315  
900/354  
1000/394  
113.9/45  
151.9/60  
189.9/75  
227.9/90  
266.2/105  
303.8/120  
341.8/135  
379.8/150  
Connecting to Various Equipment  
It only takes a few seconds to connect your projector to your computer/notebook,  
VCR or other systems. However, a Mac adapter (an optional accessory) is needed for  
connection for Macintosh users.  
Computer/  
HDTV  
S-Video/  
Video  
Audio  
Video  
S-Video  
Installation  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
BOXLIGHT XD-15c User’s Guide  
OPERATION  
Start Up  
1. Plug the power cord into a wall socket.  
2. Press POWER for 1 second.  
Remote Control  
Projector  
Power  
Power  
The back-lit POWER key blinks green and stays green when the power is turned  
on.  
(When the power is turned off, there is a 60-second cooling period before the  
projector can be re-started.)  
3. Switch on all connected equipment.  
Operation  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
BOXLIGHT XD-15c User’s Guide  
Digital Keystone Correction  
Keystoning refers to the situation where the projected image is noticeably wider at  
either the top or bottom. To correct this, press KEYSTONE +/- (hot key) on the  
control panel of the projector or on the remote control, then adjust the sliding bar  
labeled Keystone, as needed. Press + to correct keystoning at the top of the image.  
Press - to correct keystoning at the bottom of the image.  
Projector  
Auto  
Source  
Remote control  
Auto Adjustment  
In some cases, you may have to optimize the picture quality manually. To do this,  
press the AUTO key on the control panel of the projector or on the remote control.  
Within 3 seconds, the built-in Intelligent Auto Adjustment function will re-adjust to  
the best picture quality.  
Projector  
Remote control  
Auto  
Auto  
Source  
Operation  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
BOXLIGHT XD-15c User’s Guide  
Source Selection  
When several input sources are available, press the SOURCE key to make a selection  
from the control panel of the projector or the remote control.  
Remote control  
Projector  
Source  
Power  
Power  
Auto  
Source  
Menu System  
Press Menu for the main menu and press 3or 4 to select a sub-menu. Press Menu  
again to select items in the sub-menu.  
Menu Bar  
Sub-menu  
PC  
Display  
Image  
Source  
Control  
PIP  
Keystone  
Brightness  
Contrast  
Phase  
Auto resize  
H-position  
V-position  
Color Temp  
Information  
Mirror  
Source  
Volume  
Treble  
Bass  
Langauge  
OSD  
Main page:  
PIP Source  
PIP Size  
OSD Time  
Auto Off  
Reset  
PIP Pos.  
H.Size  
H. Position  
V.Position  
More  
Mute  
Lamp hour  
Auto resize  
H-position  
V-position  
Color  
Options  
Y/Pb/Pr  
Video  
Sub Page:  
Brightness  
Contrast  
Color  
Tint  
Color Temp  
Keystone  
Brightness  
Contrast  
Color  
Ratio  
System  
Tint  
Sharpness  
System  
Sharpness  
Color Temp  
Information  
Tint  
Operation  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
BOXLIGHT XD-15c User’s Guide  
1. Display Menu  
Keystone  
Corrects any keystoning of the image.  
Adjusts the brightness of the image.  
Brightness  
Contrast  
Adjusts the degree of difference between darkness and lightness of  
the image.  
Adjusts to avoid the occurrence of flicker.  
Phase  
*This function is not available when the input modes are Video, S-  
Video.  
Adjusts to fit in the desired image size.  
H.Size  
*This function is not available when the input modes are Video, S-  
Video.  
Increases or decreases the color range (R, G, B) of the image.  
*This function is not available when the input mode is PC.  
Adjusts the image to make it appear more red or blue.  
*This function is not available when the input mode is PC.  
Color  
Tint  
Operation  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
BOXLIGHT XD-15c User’s Guide  
2. Image Menu  
Makes the best fit of the image to the screen,  
Auto resize  
H-position  
Adjusts the horizontal position of the projected image.  
Adjusts the vertical positon of the projected image.  
V-position  
Adjusts the color temperature to fit your preference.  
Shows the current resolution.  
Color Temp.  
Information  
Users have 2 options for the image ratio.  
1. 4:3 (Normal) 2. 16:9 (Wide)  
Ratio  
*This function is not available when the input modes are PC, YPbPr.  
4 modes can be selected.  
1. Auto 2. PAL-M 3. PAL-N 4.SECAM  
System  
*The default setting of System is Auto.  
*This function is not available when the input modes are PC, YPbPr.  
Adjusts the image to make it look sharper or softer.  
Sharpness  
Color  
*This function is not available when the input modes are PC, YPbPr.  
Increases or decreases the color range (R, G, B) of the image.  
*This function is not available when the input mode is PC.  
Adjusts the image to make it appear more red or blue.  
*This function is not available when the input mode is PC.  
Tint  
Operation  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
BOXLIGHT XD-15c User’s Guide  
3. Source Menu  
Mirror  
2.  
1.  
1. Default  
2. Ceiling -  
mounted  
projection  
3. Rear screen  
projection  
4.  
3.  
4. Ceiling -  
mounted and  
rear screen  
projection  
Selects sources between PC, Video, S-Video, and YPbPr.  
Adjusts the volume level.  
Source  
Volume  
Adjusts the treble level.  
Adjusts the bass level.  
Treble  
Bass  
On  
Off  
Mute  
Operation  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
BOXLIGHT XD-15c User’s Guide  
4. Control Menu  
Language sets the OSD to display in one of 7 languages.  
Use 3 / 4 key to select the languages: English, French, Ger-  
man, Italian, Spanish, Simplified Chinese and Traditional Chi-  
nese.  
Language  
Selects a desired OSD position.  
OSD  
Sets the length of time the OSD will remain active after the last  
time you pressed the button. The range is from 5 to 60 sec-  
onds in 5-second increments.  
OSD Time  
Sets the length of time to shut off the system when no input is  
detected.  
Auto Off  
Returns all settings to the time of manufacturing.  
Shows lamp usage time.  
Reset  
Lamp Hour  
5. PIP Menu  
These functions are valid only when the input mode is PC and the PIP source is Video or  
S-Video.  
Selects the source for the PIP.  
PIP Source  
Uses 3 / 4 key to scroll through the 4 alternatives: Off,  
Small, Medium, Large.  
PIP Size  
Selects a desired position for the PIP.  
PIP Position  
Adjusts the horizontal position of the PIP image.  
H Position  
Adjusts the vertical position of the PIP image.  
V Position  
Uses 3 / 4 key to select more PIP functions including Bright-  
More Options  
ness, Contrast, Color, Tint, Sharpness and System.  
Adjusts the brightness of the PIP image.  
Brightness  
Adjusts the degree of difference between dark and light for the  
PIP image.  
Contrast  
Increases or decreases the color range (R, G, B) of the image.  
Color  
Adjusts the image to make it appear more red or blue.  
Tint  
Adjusts the image to make it appear sharper or softer  
Sharpness  
Selects PIP image systems: Auto, NTSC, PAL, SECAM  
System  
Operation  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
BOXLIGHT XD-15c User’s Guide  
Shutdown  
1. Press POWER and a warning message will prompt up. To turn off the projector,  
Press POWER again.  
2. The fan will continue to run for approximately 60 seconds.  
Power  
Power  
3. Disconnect the power cord from the wall socket.  
Caution  
Please do not unplug the power cord before POWER is shut down or dur-  
ing the 60-second cooling process.  
If the projector is not properly shut down, to protect the lamp, the system  
will detect this and cool the lamp for two minutes automatically before  
turning on again.  
Operation  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
BOXLIGHT XD-15c User’s Guide  
MAINTENANCE  
Lamp Information  
Use and Replacement of Lamp  
When the Lamp Indicator lights up red or a message appears suggesting the time of lamp  
replacement, please install a new lamp or consult your dealer. An old lamp could cause a  
malfunction in the projector and in rare instances may even explode.  
LED Status Indicators  
Lamp Life Indicators  
When this LED shows red continuously, it is warning you that  
the lamp usage has exceeded 150 0 hours. Replace the pro-  
jection lamp with a new one immediately.  
CHANGE THE LAMP, AND The lamp has been in operation for 1400 hours. Change a  
RESET THE LAMP TIMER  
new lamp for optimal performance.  
CHANGE THE LAMP. THE  
POWER WILL TURN OFF  
AFTER 20 HOURS  
The lamp has been in operation for 1480 hours, and the  
power will turn off after 20 hours.  
CHANGE THE LAMP!  
The lamp has been in operation for over 1500 hours. The  
warning message will display for 30 seconds every 5 minutes  
after you turn on the projector and the power will turn off  
automatically in 10 minutes.  
Lamp is not properly attached LED blinks rapidly.  
Temperature is too high  
When the projector’s internal temperature is too high to  
operate safely, the LED blinks slowly for one minute and the  
lamp turns off automatically.  
If the LED light is off, the projector’s lamp and temperature  
are operating under normal conditions.  
Caution  
The LAMP indicator will light up if the lamp becomes too hot. Turn off the  
power and let the projector cool for 45 minutes. If the LAMP indicator is still  
red when turning the power on, please contact BOXLIGHT Technical Sup-  
port at 1-800-762-5757 or +1-360-779-7901.  
Lamp Replacement  
Caution  
To reduce the risk of electrical shock, always turn off the projector and dis-  
connect the power cord before changing the lamp.  
Maintenance  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
BOXLIGHT XD-15c User’s Guide  
1. Press the POWER button to switch off the projector. Disconnect the power  
cord from the outlet and the projector.  
2. Loosen the screw and remove the lamp cover. If the lamp is hot, avoid burns by  
waiting 45 minutes until the lamp has cooled.  
3. Loosen the 3 screws. (It is strongly recommended you use a magnetic-headed  
screwdriver.) Pull the handle to remove the lamp housing. If the screws are not  
loosened completely, they could injure your fingers. Do not insert your hand into  
the box after the lamp is removed. If you touch the optical parts inside, this could  
cause color unevenness.  
4. Replace the lamp with a new one. Insert it into the projector, and tighten the  
screws firmly. Loose screws may cause a bad connection, which may result in  
malfunction.  
5. Re-install the lamp cover and tighten the screw. Do not turn on the power  
with the lamp cover removed. Whenever the lamp is replaced, reset the  
total lamp operation time. Do not reset if the lamp is not replaced as this  
could cause breakage.  
Maintenance  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BOXLIGHT XD-15c User’s Guide  
Caution  
To reduce the risk of severe burns, allow the projector to cool for at least 45  
minutes before replacing the lamp.  
To reduce the risk of injuries to fingers and damage to internal components,  
use caution when removing lamp glass that has shattered into sharp pieces.  
Please call BOXLIGHT Technial Support if your lamp has exploded.  
To reduce the risk of injuries to fingers and/or decreasing image quality by  
touching the lens, do not touch the empty lamp compartment when the  
lamp is removed.  
This lamp contains mercury. Consult your local hazardous waste regulations  
to dispose of this lamp in a proper manner.  
Resetting Lamp Hours  
If you replace the lamp after 1500 hours of operation, please follow the instructions  
below within 10 minutes of power on.  
OSD  
FUNCTION  
Press the Exit button on the projector for 3  
seconds to display the total used lamp time.  
Press the MENU button on the projector  
during the lamp hour message. An  
adjustment message will appear.  
Press W or X to rest lamp hours or press  
EXIT to leave.  
Maintenance  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
BOXLIGHT XD-15c User’s Guide  
Service Information  
Accessories (Included in the Standard Package)  
Power cord (EU)  
Power cord (US)  
Power cord (UK)  
VGA signal cable  
Video cable  
S-Video cable  
Audio cable  
Audio - PC audio cable  
Soft carrying case  
Lens cover  
Remote control  
3-2 converter  
Optional Accessories (Not Included in the Standard Package)  
Mac adapter (switchable)  
Spare lamp module  
Ordering Parts or Getting Information  
For product information, product assistance, service information, or to order  
accessories, please contact BOXLIGHT Corporation at 1-800-762-5757 or +1-360-  
Maintenance  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
BOXLIGHT XD-15c User’s Guide  
TROUBLESHOOTING  
Common Problems & Solutions  
PROBLEMS  
TRY THESE SOLUTIONS  
Plug the power cord into the AC inlet.  
Plug the power cord into the power inlet.  
Wait two minutes after the projector is turned off before turning  
the projector back on.  
NO POWER  
Check for the proper input source.  
Ensure all cables are connected properly.  
Adjust the brightness and contrast.  
Remove the lens cap.  
NO PICTURE  
Reposition the unit to improve its angle on the screen.  
Use the Keystone correction key on the control panel of the  
projector or the remote control unit.  
TRAPEZOID  
IMAGE ON  
THE SCREEN  
Select the correct video system.  
Adjust brightness, contrast, or saturation.  
POOR COLOR  
Press Auto on the control panel of the projector or the remote  
control unit to get better picture quality.  
Adjust the focus.  
Reposition the unit to improve its projection angle.  
Ensure the distance between the unit and screen is within the  
adjustment range of the lens.  
BLURRED  
IMAGE  
Replace the batteries with new ones.  
Make sure there is no obstacle between the remote control and  
the projector.  
Stand within 6 meters (20 feet) of the unit.  
Make sure nothing is blocking the front and rear receivers.  
REMOTE  
CONTROL  
DOES NOT  
WORK  
Troubleshooting  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
BOXLIGHT XD-15c User’s Guide  
Status Messages  
On Screen Messages  
SEARCHING  
Description  
Projector is searching for input.  
Projector has identified the input signal and is running the auto  
image adjustment function.  
INPUT SIGNAL  
DETECTED,  
ACTIVATING AUTO  
IMAGE  
Input signal frequency exceeds the projector’s range.  
SYNC IS OUT OF  
RANGE  
The lamp has been in operation for 1400 hours. Lamp replace-  
ment is recommended.  
CHANGE THE LAMP,  
AND RESET THE LAMP  
TIMER  
The lamp has been in operation for 1480 hours, and the power  
will turn off after 20 more hours. Replace the lamp as soon as  
possible.  
CHANGE THE LAMP,  
THE POWER WILL  
TURN OFF AFTER 20  
HOURS  
The lamp has been in operation for over 1500 hours, and the  
power will turn off automatically in 10 minutes. Replace the  
lamp immediately.  
CHANGE THE LAMP!  
Troubleshooting  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
BOXLIGHT XD-15c User’s Guide  
SPECIFICATIONS  
Projector Specifications  
Technical Specifications  
Note: All specifications are subject to change without notice.  
General  
Product name  
Model name  
Personal Projector  
BOXLIGHT XD-15c  
1024X768 XGA  
Optical  
Display system  
Lens F/Number  
Lamp  
1-CHIP DMD  
F/2.6  
120W VIP lamp  
Electrical  
Power supply  
Power consumption  
Mechanical  
Dimensions  
AC100 ~ 240V, 2.3A, 50/60 Hz (Automatic)  
185 W (Max)  
220mm/8.7in(W) x 52mm/2.1in(H) x 175mm/6.9in(D)  
10°C ~ 40°C  
Operating Temperature  
range  
Weight  
3.85 lbs (1.69 Kg)  
Input terminal  
Computer Input  
RGB/ HDTV Input  
Video Signal Input  
S VIDEO  
D-sub 15-pin (female)  
Mini DIN 4-pin terminal  
RCA Jack terminal  
VIDEO  
Audio Signal Input  
Audio  
Mini Jack Stero Terminal  
1 Watt x 1  
Output  
Speaker  
Specifications  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
BOXLIGHT XD-15c User’s Guide  
Timing Chart  
Resolution  
640x350  
640x400  
720x400  
720x400  
640x480  
640x480  
640x480  
640x480  
800x600  
800x600  
800x600  
800x600  
800x600  
832x624  
1024x768  
1024x768  
1024x768  
1024x768  
1280x1024  
H Sync (kHz)  
31.5  
V Sync (Hz)  
Remark  
70.1  
85.1  
70.0  
85.1  
60.0  
72.8  
66.7  
85.0  
56.3  
60.3  
75.0  
72.2  
85.1  
74.5  
60.0  
70.1  
75.0  
85.0  
60.0  
37.9  
VESA  
31.5  
37.9  
VESA  
VESA  
31.5  
37.9  
VESA  
35.0  
Macintosh  
VESA  
43.3  
35.2  
VESA  
37.9  
VESA  
46.9  
VESA  
48.1  
VESA  
53.7  
VESA  
49.7  
Macintosh  
VESA  
48.4  
56.5  
VESA  
60.0  
VESA  
68.7  
VESA  
64.0  
VESA  
Specifications  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
BOXLIGHT XD-15c User’s Guide  
DIMENSIONS  
220mm  
175 mm  
52mm  
Dimensions  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 

Belkin Network Router 8820ED00372_F7D2301_V1 User Manual
Black Box Network Hardware ACU1022A User Manual
Black Decker Saw 629634 00 User Manual
Boston Acoustics Car Speaker boston mobile audio performance standard coaxial speakers User Manual
Braun Wheelchair 32221 User Manual
Broilmaster Burner SSG36LP User Manual
Brother Fax Machine FAX 1560 User Manual
Casio Watch 2171 1 User Manual
Char Broil Gas Grill 463460711 User Manual
Chromalox Gas Heater PE433 3 User Manual