BOXLIGHT Projector MP 42T User Manual

USER’S GUIDE

BOXLIGHT MP-42t

Download from Www.Somanuals.com. All Manuals Search And Download.

SAFETY INSTRUCTIONS

All the safety and operating instructions should be read before

the product is operated.

This projector should be operated only from the type of power

source indicated on the marking label. If you are not sure of

the type of power supplied, consult your authorized dealer or

local power company.

Read all of the instructions given here and retain them for later

use. Unplug this projector from AC power supply before

cleaning. Do not use liquid or aerosol cleaners. Use a damp

cloth for cleaning.

Do not overload wall outlets and extension cords as this can

result in fire or electric shock. Do not allow anything to rest on

the power cord. Do not locate this projector where the cord

may be damaged by persons walking on it.

Follow all warnings and instructions marked on the projector.

For added protection to the projector during a lightning storm,

or when it is left unattended and unused for long periods of

time, unplug it from the wall outlet. This will prevent damage

due to lightning and power line surges.

Do not attempt to service this projector yourself as opening or

removing covers may expose you to dangerous voltage or

other hazards. Refer all servicing to qualified service

personnel.

Unplug this projector from wall outlet and refer servicing to

qualified service personnel under the following conditions:

a. When the power cord or plug is damaged or frayed.

b. If liquid has been spilled into the projector.

Do not expose this unit to rain or use near water... for

example, in a wet basement, near a swimming pool, etc...

Do not use attachments not recommended by the

manufacturer as they may cause hazards.

c. If the projector has been exposed to rain or water.

d. If the projector does not operate normally by following the

operating instructions. Adjust only those controls that are

covered by the operating instructions as improper

adjustment of other controls may result in damage and will

often require extensive work by a qualified technician to

restore the projector to normal operation.

e. If the projector has been dropped or the cabinet has been

damaged.

f. When the projector exhibits a distinct change in

performance-this indicates a need for service.

Do not place this projector on an unstable cart, stand, or table.

The projector may fall, causing serious injury to a child or

adult, and serious damage to the projector. Use only with a

cart or stand recommended by the manufacturer, or sold with

the projector. Wall or shelf mounting should follow the

manufacturer's instructions, and should use a mounting kit

approved by the manufacturers.

An appliance and cart combination should

be moved with care. Quick stops,

excessive force, and uneven surfaces

may cause the appliance and cart

combination to overturn.

When replacement parts are required, be sure the service

technician has used replacement parts specified by the

manufacturer that have the same characteristics as the

original part. Unauthorized substitutions may result in fire,

electric shock, or injury to persons.

Upon completion of any service or repairs to this projector, ask

the service technician to perform routine safety checks to

determine that the projector is in safe operating condition.

Slots and openings in the back and bottom of the cabinet are

provided for ventilation, to insure reliable operation of the

equipment and to protect it from overheating.

The openings should never be covered with cloth or other

materials, and the bottom opening should not be blocked by

placing the projector on a bed, sofa, rug, or other similar

surface. This projector should never be placed near or over a

radiator or heat register.

This projector should not be placed in a built-in installation

such as a book case unless proper ventilation is provided.

Voor de klanten in Nederland

Bij dit product zijn batterijen

geleverd.

Wanneer deze leeg zijn,

moet u ze niet weggooien

maar inleveren als KCA.

Never push objects of any kind into this projector through

cabinet slots as they may touch dangerous voltage points or

short out parts that could result in a fire or electric shock.

Never spill liquid of any kind on the projector.

Download from Www.Somanuals.com. All Manuals Search And Download.

COMPLIANCES

Federal Communication Commission Notice

Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following measures :

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.

Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such

changes or modifications should be made, you could be required to stop operation of the equipment.

Model Number

Trade Name

Responsible party

Address

: BOXLIGHT MP-42t

: Boxlight

: BOXLIGHT

: 19332 Powder Hill Place Poulsbo, WA 98370-7407 USA

Telephone No.

: (800)762-5757

AC POWER CORD REQUIREMENT

The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.

AC Power Cord for the United States and Canada :

AC Power Cord used in the United States and Canada is listed by the Underwriters

Laboratories (UL) and certified by the Canadian Standard Association (CSA).

AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure that the

plug will fit into the power outlet. Do not try to defeat this safety feature. Should you be

unable to insert the plug into the outlet, contact your electrician.

GROUND

THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE.

Download from Www.Somanuals.com. All Manuals Search And Download.

TABLE OF CONTENTS

FEATURES AND DESIGN

COMPUTER MODE

SELECTING INPUT SOURCE

SELECTING COMPUTER SYSTEM

PREPARATION

PC ADJUSTMENT

AUTO PC ADJUSTMENT

MANUAL PC ADJUSTMENT

COMPATIBLE COMPUTER SPECIFICATIONS

NAME OF EACH PART OF PROJECTOR

SETTING-UP PROJECTOR

CONNECTING AC POWER CORD

POSITIONING PROJECTOR

ADJUSTABLE FEET

PICTURE IMAGE ADJUSTMENT

IMAGE LEVEL SELECT

IMAGE LEVEL ADJUSTMENT

MOVING PROJECTOR

PICTURE SCREEN ADJUSTMENT

CONNECTING PROJECTOR

11 VIDEO MODE

SELECTING INPUT SOURCE

SELECTING VIDEO SYSTEM

PICTURE IMAGE ADJUSTMENT

IMAGE LEVEL SELECT

TERMINALS OF PROJECTOR

CONNECTING TO COMPUTER

CONNECTING TO VIDEO EQUIPMENT

IMAGE LEVEL ADJUSTMENT

PICTURE SCREEN ADJUSTMENT

BEFORE OPERATION

OPERATION OF REMOTE CONTROL

LASER POINTER FUNCTION

SETTING

REMOTE CONTROL BATTERIES INSTALLATION

SETTING MENU

TOP CONTROLS AND INDICATORS

OPERATING ON-SCREEN MENU

HOW TO OPERATE ON-SCREEN MENU

FLOW OF ON-SCREEN MENU OPERATION

MENU BAR

APPENDIX

OPERATING WIRELESS MOUSE

MAINTENANCE

BASIC OPERATION

WARNING TEMP. INDICATOR

AIR FILTER CARE AND CLEANING

CLEANING PROJECTION LENS

LAMP REPLACEMENT

TURNING ON / OFF PROJECTOR

ADJUSTING SCREEN

ZOOM ADJUSTMENT

LAMP REPLACE COUNTER

TROUBLESHOOTING

TECHNICAL SPECIFICATIONS

FOCUS ADJUSTMENT

LENS SHIFT ADJUSTMENT

KEYSTONE ADJUSTMENT

PICTURE FREEZE FUNCTION

NO SHOW FUNCTION

P-TIMER FUNCTION

SOUND ADJUSTMENT

TRADEMARKS

● Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer,Inc.

● IBM and PS/2 are trademarks or registered trademarks of International Business Machines, Inc.

● Windows and PowerPoint are registered trademarks of Microsoft Corporation.

● Each name of corporations or products in the user's guide is a trademark or a registered trademark of its

respective corporation.

Download from Www.Somanuals.com. All Manuals Search And Download.

FEATURES AND DESIGN

This Multimedia Projector is designed with most advanced technology for portability, durability, and ease of use. This

projector utilizes built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal display (LCD)

technology.

● Compact Design

● Digital Zoom (for Computer)

This projector is extremely compact in size and weight.

It is designed to carry and work anywhere you wish to

use.

Digital Zoom function adjusts image size to approx. 1/4 ~

49 times of original image size, allowing you to focus on

crucial information at a presentation.

● Keystone Correction

● Compatibility

Positioning of a projector may result in distorted image

being displayed in a trapezoid shape. Keystone

Correction solves this problem by digitally altering

projection to produce undistorted images.

This projector widely accepts various video and

computer input signals including;

● Computers

IBM-compatible or Macintosh computer up to 1280

x 1024 resolution.

● Power Management

● 6 Color Systems

Power Management function is provided to reduce power

consumption while a projector is not in use.

NTSC, PAL, SECAM, NTSC 4.43, PAL-M or PAL-

N color system can be connected.

This Power Management function operates to turn

Projection Lamp off when a projector detects signal

interruption and any button is not pressed over 5

minutes. Projection Lamp is automatically turned on

again when a projector detects signal or any operation

button is pressed.

● Component Video

Component video signal, such as a DVD player

output high definition TV signals including 480i,

480p, 575i, 575p, 720p, 1035i or 1080i, can be

connected.

This projector is shipped with this function ON.

● S-Video

S-Video signal, such as a S-VHS VCR output

signal, can be connected.

● Digital Visual Interface

This projector is equipped with DVI 24-pin terminal for

connecting DVI output from a computer.

● High Resolution Image

This projector provides 1024 x 768 dots resolution for

computer input and 800 horizontal TV lines. Resolution

from a computer between XGA (1024 x 768) and SXGA

(1280 x 1024) is compressed into 1024 x 768 dots. This

projector cannot display image of over 1280 x 1024 dots.

When resolution of your computer is over than 1280 x

1024, reset a computer output for lower resolution.

● Laser Pointer Function

Remote Control Unit supplied with this projector includes

Laser Pointer function. This function helps you to make

a smart presentation on a projected screen.

● Wireless Mouse

Remote Control Unit supplied with this projector has

Wireless Mouse function for a connected computer. This

function enables you to operate both projector and

computer with Remote Control Unit only.

● Multi-Scan System

This projector has Multi-Scan System to conform to

almost all computer output signals quickly. There is no

need for troublesome manual adjustment of frequency

and other settings.

● Multilanguage Menu Display

Operation menu is displayed in; English, German,

French, Italian, Spanish, Portuguese, Dutch, Swedish,

Chinese, Korean or Japanese.

● One-Touch Auto PC Adjustment

Incoming computer video signals are recognized and

best adjustment is automatically set by Auto PC

Adjustment. No complicated setup is necessary and

projection is always precise.

● Motor-driven Lens Shift

Projection lens can be moved up and down with motor-

driven lens shift function. This function makes it easy to

provide projected image where you want.

Zoom and focus can be also adjusted with motor-driven

operation.

Download from Www.Somanuals.com. All Manuals Search And Download.

PREPARATION

NAME OF EACH PART OF PROJECTOR

FRONT OF CABINET

TOP CONTROLS

AND INDICATORS

PROJECTION LENS

AIR INTAKE

VENT

INFRARED

REMOTE RECEIVER

LENS COVER

SPEAKERS

BACK OF CABINET

EXHAUST VENT

TERMINALS

AND CONNECTORS

INFRARED

REMOTE RECEIVER

POWER CORD

CONNECTOR

HOT AIR EXHAUSTED !

Air blown from exhaust vent is hot. When

using or installing a projector, following

precautions should be taken.

● Do not put a flammable object near this vent.

● Keep rear grills at least 3’(1 m) away from

any object, especially heat-sensitive object.

● Do not touch this area, especially screws

and metallic parts. This area will become

hot while a projector is used.

CARRYING

HANDLE

This projector detects internal temperature

and automatically controls operating power

of Cooling Fans.

LAMP COVER

When attached the network option to the

projector, remove the these parts.

BOTTOM OF CABINET

AIR INTAKE VENTS

This projector is equipped with cooling fans for protection from

overheating. Pay attention to following to ensure proper ventilation

and avoid a possible risk of fire and malfunction.

● Do not cover vent slots.

● Keep side clear of any objects. Obstructions may block cooling

air.

ADJUSTABLE FEET

AND

FEET LOCK LATCHES

Download from Www.Somanuals.com. All Manuals Search And Download.

PREPARATION

SETTING-UP PROJECTOR

CONNECTING AC POWER CORD

This projector uses nominal input voltages of 100-120 V or 200-240

V AC. This projector automatically selects correct input voltage. It

is designed to work with single-phase power systems having a

grounded neutral conductor. To reduce risk of electrical shock, do

not plug into any other type of power system.

Consult your authorized dealer or service station if you are not sure

of type of power supply being in use.

Connect a projector with a peripheral equipment before turning a

projector on. (Refer to pages 11 ~ 13 for connection.)

CAUTION

For safety, unplug AC Power Cord when an appliance is not

used.

Connect AC Power Cord (supplied) to a projector.

AC outlet must be near this equipment and must

be easily accessible.

When this projector is connected to outlet with AC Power Cord,

an appliance is in Stand-by Mode and consumes a little electric

power.

NOTE ON POWER CORD

AC Power Cord must meet requirement of country where you use a projector.

Confirm AC plug type with chart below and proper AC power cord must be used.

If supplied AC Power Cord does not match AC outlet, contact your sales dealer.

Projector side

AC Outlet side

For U.S.A. and Canada

For Continental Europe

Ground

To POWER CORD

CONNECTOR on a

projector.

To AC Outlet.

(120 V AC)

To AC Outlet.

(200 - 240 V AC)

Download from Www.Somanuals.com. All Manuals Search And Download.

PREPARATION

POSITIONING PROJECTOR

● This projector is designed to project on a flat

ROOM LIGHT

projection surface.

● Projector can be focused from 4.6’ (1.4m) ~ 48.3’

(14.7m).

Brightness in room has a great influence on

picture quality. It is recommended to limit

ambient lighting in order to provide best

image.

● Refer to figure below to adjust screen size.

48.3’(14.7m)

36.1’(11.0m)

400”

Max. Zoom

Min. Zoom

24.0’(7.3m)

300”

231”

11.8’(3.6m)

4.6’(1.4m)

308”

200”

154”

100”

77”

40”

31”

Max. Zoom

Min. Zoom

40”

31”

100”

77”

150”

200”

154”

250”

192”

300”

231”

400”

308”

Screen

Size

115”

4.6’ (1.4m)

11.8’ (3.6m)

17.7’ (5.4m)

24.0’ (7.3m)

30.2’ (9.2m) 36.1’ (11.0m) 48.3’ (14.7m)

Distance

LENS SHIFT ADJUSTMENT

Projection lens can be moved up and down with motor-driven lens shift function. This function makes it easy to

provide projected image where you want. U/D ratio can be adjusted 10 : 0 ~ 1 : 1 (refer to figure below.). Refer

to P 20 for operation.

Highest (10 : 0)

Lowest (1 : 1)

10 : 0

Download from Www.Somanuals.com. All Manuals Search And Download.

PREPARATION

ADJUSTABLE FEET

Picture tilt and projection angle can be adjusted by

rotating ADJUSTABLE FEET. Projection angle can be

adjusted to 10.5 degrees.

Lift front of a projector and pull FEET LOCK LATCHES

on both sides of a projector.

Release FEET LOCK LATCHES to lock ADJUSTABLE

FEET and rotate ADJUSTABLE FEET to fine tune

position and tilt.

To shorten ADJUSTABLE FEET, lift front of a projector

and pull and undo FEET LOCK LATCHES.

Position and keystone distortion of image can be adjusted

using Menu Operation. (Refer to P 20 and 35.)

ADJUSTABLE FEET

FEET LOCK

LATCHES

NOTE :

THIS PROJECTOR SHOULD BE SET IN THE WAY

INDICATED. PROJECTION LAMP MAY MALFUNCTION.

MOVING PROJECTOR

Use Carry Handle when moving a Projector.

When moving a projector, replace lens cover and retract

feet to prevent damage to lens and cabinet.

When this projector is not in use for an extended period,

put it into case (dust cover) supplied with this projector.

CAUTION IN CARRYING OR TRANSPORTING A PROJECTOR

● Do not drop or bump a projector, otherwise damages or malfunctions may result.

● When carrying a projector, use a suitable carrying case.

● Do not transport a projector by using a courier or transport service in an unsuitable transport case. This

may cause damage to a projector. To transport a projector through a courier or transport service, consult

your dealer for best way.

Download from Www.Somanuals.com. All Manuals Search And Download.

CONNECTING PROJECTOR

TERMINALS OF PROJECTOR

This projector has input and output terminals on its back for connecting computers and video equipment. Refer to figures on

pages 11 to 13 and connect properly.

COMPUTER INPUT

TERMINALS (DIGITAL/ANALOG)

COMPUTER AUDIO

INPUT (1 and 2) JACKS

Connect computer (digital/analog)

output to one of these terminals.

(Refer to P12.)

Connect an audio output

(stereo) from computer to

these jacks.

R/C JACK

When using Wired/Wireless

Remote Control Unit as Wired

Remote Control, Connect

Wired Remote Control Unit to

this jack with Remote Control

Cable (supplied).

(Refer to P12.)

INPUT 1

DIGITAL(DVI-D)

USB CONNECTOR (Series B)

ANALOG

R/C JACK

When controlling computer with

Remote Control Unit of this

projector, connect mouse port

of your personal computer to

this terminal. (Refer to P12.)

CONTROL PORT

RESET

USB

AUDIO 1

AUDIO 2

CONTROL PORT CONNECTOR

H/V

When controlling computer

with Remote Control Unit of

this projector, connect mouse

port of your personal computer

to this connector. (Refer to

P12.)

VIDEO/Y Cb/Pb

Cr/Pr

INPUT 2

RESET BUTTON

S–VIDEO

VIDEO/Y Cb/Pb Cr/Pr

R–AUDIO–L

This projector uses a micro processor

to control this unit, and occasionally,

this micro processor may malfunction

and need to be reset. This can be

done by pressing RESET button with a

pen, which will shut down and restart

unit. Do not use RESET function

excessively.

(

)

MONO

INPUT 3

● Do not press this button. This button

is used for our optional accessories.

VIDEO INPUT JACKS

AUDIO INPUT JACKS

S-VIDEO INPUT JACK

Connect composite video Connect an audio output Connect S-VIDEO

output from video equipment from video equipment to output from video

5 BNC INPUT JACKS

to VIDEO/Y jack or connect these jacks.

component video outputs to (Refer to P13.)

VIDEO/Y, Cb/Pb and Cr/Pr

equipment to this

jack. (Refer to P13.)

Connect component video

output (Y, Cb, Cr or Y, Pb, Pr)

from video equipment to

VIDEO/Y, Cb/Pb and Cr/Pr

jacks or connect computer

output {5 BNC Type (Green,

Blue, Red, Horiz. Sync and

Vert. Sync.)} from computer

to G, B, R, H/V and V jacks.

(Refer to P12 and 13.)

jacks. (Refer to P13.)

Download from Www.Somanuals.com. All Manuals Search And Download.

CONNECTING PROJECTOR

CONNECTING TO COMPUTER

Cables used for connection (● = Cable or adapter is not supplied with this projector.)

• VGA Cable (HDB 15 pin)

• USB Cable ●

• DVI-Digital Cable (for Single Link T.M.D.S.) ●

• BNC Cable ●

• MAC Adapter (When connecting to Macintosh computer)

• Audio Cables (RCA x 2 and Mini Plug (stereo) x 1) ●

• Control Cable for PS/2 Port, Serial Port or ADB Port

IBM-compatible computer or Macintosh computer (VGA / SVGA / XGA / SXGA)

Desktop type

Laptop type

ADB port

Monitor Output

Audio Output

PS/2 port

Monitor Output

USB port

Serial port

Control Cable

for ADB Port

USB

Cable ●

Control Cable

for Serial Port

Control Cable

for PS/2 Port

Audio

Cable ●

(stereo)

MAC Adapter

DVI

Cable ●

Set slide switches

according to chart

below.

Terminal

BNC

Cable ●

VGA Cable

COMPUTER

AUDIO IN 1 or 2

Use one of these Control

Cables corresponding with

terminal of your computer.

USB

COMPUTER IN ANALOG

COMPUTER IN DIGITAL

CONTROL

PORT

INPUT 1

DIGITAL(DVI-D)

ANALOG

R/C JACK

CONTROL PORT

RESET

USB

AUDIO 1

AUDIO 2

H/V

VIDEO/Y Cb/Pb

Cr/Pr

INPUT 2

S–VIDEO

VIDEO/Y Cb/Pb Cr/Pr

R–AUDIO–L

(

)

MONO

Terminals

INPUT 3

of a Projector

● MAC ADAPTER

NOTE :

When connecting cable, power cords of both

Set switches as shown in table

below depending on RESOLU-

TION MODE that you want to

use before you turn on projec-

tor and computer.

a projector and external equipment should

be disconnected from AC outlet. Turn a

projector and peripheral equipment on

before computer is switched on.

DIP

OFF

13" MODE (640 x 480)

ON OFF OFF OFF OFF

16" MODE (832 x 624) OFF ON OFF ON OFF OFF

19" MODE (1024 x 768) OFF ON

21" MODE (1152 x 870) ON ON

ON OFF OFF OFF

ON ON OFF OFF

Download from Www.Somanuals.com. All Manuals Search And Download.

CONNECTING PROJECTOR

CONNECTING TO VIDEO EQUIPMENT

Cables used for connection (● = Cable is not supplied with this projector.)

• Video Cable (RCA x 1 or RCA x 3) ●

• BNC Cable ●

• S-VIDEO Cable ●

• Audio Cable (RCA x 2) ●

Video Source (example)

Component video output equipment.

(such as DVD player or high-definition TV source.)

Video Cassette Recorder

Video Disc Player

Composite Component Video Output

Composite Component Video Output Audio Output

Video Output

(Y, Cb/Pb, Cr/Pr)

S-VIDEO Output

Video Output

(Y, Cb/Pb, Cr/Pr)

Video Cables

(RCA x 1 or

RCA x 3) ●

Audio Cable

(RCA x 2) ●

S-VIDEO

Cable ●

BNC Cable ●

VIDEO

Y - Cb/Pb - Cr/Pr VIDEO

Y - Cb/Pb - Cr/Pr AUDIO IN

S-VIDEO

INPUT 1

ANALOG

DIGITAL(DVI-D)

R/C JACK

CONTROL PORT

RESET

USB

AUDIO 1

AUDIO 2

H/V

VIDEO/Y Cb/Pb

Cr/Pr

INPUT 2

S–VIDEO

VIDEO/Y Cb/Pb Cr/Pr

R–AUDIO–L

(

)

MONO

INPUT 3

Terminals

of a Projector

NOTE :

When connecting cable, power cords of

both a projector and external equipment

should be disconnected from AC outlet.

Download from Www.Somanuals.com. All Manuals Search And Download.

BEFORE OPERATION

OPERATION OF REMOTE CONTROL

Left Side

LASER POINTER INDICATOR

POWER ON-OFF BUTTON

Used to turn projector on or

off. (P19)

Lights red while laser beam

is emitted from Laser Light

Window.

ON-OFF

ZOOM FOCUS

VOLUME

INPUT BUTTON

Used to select input source.

(P22)

D.ZOOM

MUTE

INPUT

MENU BUTTON

POINT BUTTON

Used to select MENU

operation. (P17, 18)

Used to move a pointer on ON-

SCREEN MENU, adjust each

item, or pan image in DIGITAL

ZOOM +/– mode. (P29)

It is also used as a PC mouse

in Wireless Mouse Operation.

(P37)

SELECT BUTTON

Used to execute item

selected, or to expand

or compress image in

DIGITAL ZOOM +/–

mode. (P29)

It is also used as a PC

mouse in Wireless

Mouse Operation. (P37)

● When pressing center of this

button, it works as SELECT

button.

ALL-OFF SWITCH

LASER

When using Remote Control Unit,

turn this switch to “ON.” And turn it

to “ALL OFF” when it is not used.

KEYSTONE

NO SHOW

RIGHT CLICK BUTTON

LENS SHIFT

Used as a PC mouse in

Wireless Mouse Operation.

(P37)

FREEZE

LASER BUTTON

AUTO PC ADJ.

P-TIMER

IMAGE

Used to operate Laser Pointer

Function. Laser beam is

emitted while pressing this

button within 1 minute.

When using this Laser Pointer

for more than 1 minute, release

LASER button and press it

again.

P-TIMER BUTTON

Used to operate P-TIMER

function. (P21)

LASER POINTER FUNCTION

This Remote Control Unit emits a laser beam as laser pointer function from Laser Light Window. When LASER button is

pressed, laser light goes on. And when LASER button is being pressed for more than 1 minute or LASER button is released,

light goes off. LASER POINTER INDICATOR lights RED and Laser is emitted with RED light to indicate laser beam is being

emitted.

Laser emitted is a class II laser; therefore, do not look into Laser Light Window or shine laser beam on yourself or other

people. Three marks bellow are caution labels for laser beam.

CAUTION : Use of controls, adjustments or performance of procedures other than those specified herein may result

hazardous radiation exposure.

These caution labels are put on remote control.

LASER POINTER INDICATOR

Laser Light Window

Download from Www.Somanuals.com. All Manuals Search And Download.

BEFORE OPERATION

Operating Range

ON-OFF

Point Remote Control Unit toward

projector (Receiver Window)

whenever pressing any button.

Maximum operating range for

Remote Control Unit is about 16.4’

(5m) and 60° in front and rear of a

projector.

ZOOM BUTTON

Used to adjust zoom.

(P20)

VOLUME BUTTON

Used to adjust volume.

(P21)

ZOOM FOCUS

VOLUME

FOCUS BUTTON

Used to adjust focus.

(P20)

D.ZOOM

MUTE

INPUT

D.ZOOM BUTTON

Used to select DIGITAL

ZOOM +/– mode and

resize image. (P29)

MUTE BUTTON

60°

Used to mute sound.(P21)

KEYSTONE BUTTON

Used to correct

keystone distortion.

(P20, 35)

16.4’

(5 m)

LASER

KEYSTONE

NO SHOW

FREEZE BUTTON

Used to freeze picture.

(P21)

NO SHOW BUTTON

Used to turn picture into

black image. (P21)

LENS SHIFT

FREEZE

IMAGE BUTTON

Used to select image

level. (P27, 32)

AUTO PC ADJ.

P-TIMER

IMAGE

AUTO PC ADJ. BUTTON

Use to operate AUTO PC

Adjustment function. (P23)

16.4’

(5 m)

LENS SHIFT BUTTON

Used to select LENS

SHIFT function. (P20)

WIRED REMOTE JACK

60°

When using as Wired

Remote Control, connect

Remote Control Cable to

this jack.

Battery installation is

required when using as

Wired Remote Control.

Remote Control Batteries Installation

Remove battery

compartment lid.

Slide batteries into

compartment.

Replace compartment lid.

Two AA size batteries

Press lid down-

ward and slide it.

For correct polarity (+ and

–), be sure battery

terminals are in contact

with pins in compartment.

To insure safe operation, please observe following precautions :

● Use (2) AA, UM3 or R06 type alkaline batteries.

● Replace two batteries at same time.

● Do not use a new battery with an used battery.

● Avoid contact with water or liquid.

● Do not expose Remote Control Unit to moisture, or heat.

● Do not drop Remote Control Unit.

● If a battery has leaked on Remote Control Unit, carefully wipe case clean and install new batteries.

● Danger of explosion if battery is incorrectly replaced.

● Dispose of used batteries according to batteries manufacturers instructions and local rules.

Download from Www.Somanuals.com. All Manuals Search And Download.

BEFORE OPERATION

TOP CONTROLS AND INDICATORS

This projector has CONTROL BUTTONS (TOP CONTROLS) and INDICATORS on its top.

LAMP REPLACE INDICATOR

WARNING TEMP. INDICATOR

READY INDICATOR

LAMP INDICATOR

Turns to yellow when

life of projection lamp

draws to an end. (P39)

Flashes red when

Lights green when a

projector is ready to be

Becomes dim when a

projector is turned on.

And bright when a

projector is in stand-by

mode.

internal

projector

temperature is too

high. (P38)

turned on.

And it

flashes green in Power

Management mode.

(P36)

POWER ON–OFF BUTTON

Used to turn a projector

on or off. (P19)

MENU BUTTON

Used to open or close

MENU operation. (P17,

18)

INPUT BUTTON

Used to select input

source. (P22)

ZOOM BUTTON

Used to adjust zoom.

(P20)

FOCUS BUTTON

Used to adjust focus.

(P20)

AUTO PC ADJ. BUTTON

LENS SHIFT BUTTON

Used to operate AUTO PC

Adjustment function. (P23)

Used to select LENS

SHIFT function. (P20)

IMAGE BUTTON

Used to select image

level. (P27, 32)

SELECT BUTTON

POINT (VOLUME + / – ) BUTTONS

Used to execute item

selected. It is also used

to expand / compress

image in DIGITAL

ZOOM mode. (P29)

Used to select an item or adjust

value in ON-SCREEN MENU. They

are also used to pan image in

DIGITAL ZOOM +/– mode. (P29)

POINT LEFT/RIGHT buttons are

also used as VOLUME +/– buttons.

Download from Www.Somanuals.com. All Manuals Search And Download.

BEFORE OPERATION

OPERATING ON-SCREEN MENU

HOW TO OPERATE ON-SCREEN MENU

You can control and adjust this projector through ON-SCREEN

MENU. Refer to following pages to operate each adjustment on

ON-SCREEN MENU.

WIRELESS REMOTE CONTROL

POINT BUTTON

Used to move Pointer

UP/ DOWN/ RIGHT/

LEFT.

1 DISPLAY MENU

Press MENU button to display ON-SCREEN MENU.

2 MOVING POINTER

SELECT BUTTON

Used to select item.

Move pointer (● see below) or adjust value of item by pressing

POINT button(s) on Top Control or on Remote Control Unit.

● Pointer is icon on ON-SCREEN MENU to select item. See fig-

ures on section "FLOW OF ON-SCREEN MENU OPERATION"

below.

TOP CONTROL

POINT BUTTONS

Used to move Pointer

UP/ DOWN/ RIGHT/

LEFT.

3 SELECT ITEM

Select item or set selected function by pressing SELECT button.

SELECT BUTTON

Used to select item.

FLOW OF ON-SCREEN MENU OPERATION

MENU BAR

MENU ICON

Display ON-SCREEN MENU

Press MENU button to display ON-SCREEN MENU (MENU

BAR). A red frame is POINTER.

POINTER

(red frame)

POINTER (red frame)

Press POINT DOWN button to

move POINTER.

Select Menu to be adjusted

Move POINTER (red frame) to MENU ICON that you want to

select by pressing POINT RIGHT / LEFT buttons.

ITEM

Control or adjust item through ON-SCREEN MENU

Press POINT DOWN button and move POINTER (red frame

or red arrow) to ITEM that you want to adjust, and then press

SELECT button to show ITEM DATA.

SELECT

BUTTON

Adjust ITEM DATA by pressing POINT RIGHT / LEFT

buttons.

Refer to following pages for details of respective

adjustments.

ITEM DATA

Press POINT LEFT/RIGHT

buttons to adjust value or

set function.

Download from Www.Somanuals.com. All Manuals Search And Download.

BEFORE OPERATION

MENU BAR

FOR PC SOURCE

Press MENU BUTTON while connecting to PC input source.

IMAGE SELECT MENU

SCREEN MENU

SETTING MENU

Used to select

Used to adjust size

of image. [Normal

/ True / Wide /

Digital zoom +/–]

(Refer to P29)

Used to change

settings of projector

or reset Lamp

Replace Counter.

(Refer to P35,-37)

GUIDE WINDOW

PC SYSTEM MENU

image level among

Standard, Real

and Image 1 ~ 4.

(Refer to P27)

Shows selected

item of ON-

SCREEN MENU.

Used to select

computer system.

(Refer to P22, 23)

INPUT MENU

PC ADJUST MENU

IMAGE ADJUST MENU

SOUND MENU

Used to select

Used to adjust

parameters to

match with input

signal format.

Used to adjust

volume or mute

sound.

input source (Input

1, Input 2 or Input

3). (Refer to P22)

computer image.

[Contrast / Brightness

/ White Balance

(R/G/B) / Gamma]

(Refer to P28)

(Refer to P21)

(Refer to P23-25)

FOR VIDEO SOURCE

Press MENU BUTTON while connecting to VIDEO input source.

INPUT MENU

Used to select

input source

(Input 1, Input 2

or Input 3).

IMAGE SELECT MENU

SCREEN MENU

Used to select image

level among

Standard, Cinema

and Image 1 ~ 4.

(Refer to P32)

Used to set size of

image to Normal

or Wide.

(Refer to P30)

(Refer to P34)

AV SYSTEM MENU

IMAGE ADJUST MENU

Same function as

Menu for PC source.

Same function as

Menu for PC source.

Used to select

system of selected

video source.

Used to adjust picture image.

[Contrast / Brightness / Color /

Tint / White balance (R/G/B) /

Sharpness / Gamma/Noise

Reduction/Progressive]

(Refer to P31)

(Refer to P33, 34)

Download from Www.Somanuals.com. All Manuals Search And Download.

BEFORE OPERATION

TURNING ON / OFF PROJECTOR

TURNING ON PROJECTOR

Complete peripheral connections (with Computer, VCR, etc.)

before turning on projector. (Refer to "CONNECTING TO

PROJECTOR" on pages 11~13 for connecting that equipment.)

Input position and

Lamp mode status

Input 1

Connect a projector's AC Power Cord into an AC outlet. LAMP

Indicator lights RED, and READY Indicator lights GREEN.

NOTE : When “On start” function is ON, this projector is turned

on automatically by connecting AC Power Cord to an

AC outlet. (Refer to pages 35, 36.)

Press POWER ON-OFF button on Top Control or on Remote

Control Unit to ON. LAMP Indicator dims, and Cooling Fans

start to operate. Preparation Display appears on a screen and

count-down starts. Signal from PC or Video source appears after

30 seconds.

Preparation Display disappears after 30 seconds.

Current Input position and Lamp mode status are also displayed

on screen for 5 seconds. (Refer to "LAMP MODE" on page 36.)

TURNING OFF PROJECTOR

Press POWER ON-OFF button on Top Control or on Remote

Control Unit, and a message "Power off?" appears on a screen.

Press POWER ON-OFF button again to turn off projector. LAMP

Indicator lights bright and READY Indicator turns off. After

projector is turned off, Cooling Fans operate (for 90 seconds).

During this "Cooling Down" period, this appliance cannot be

turned on.

Power off?

When projector has cooled down, READY Indicator lights

GREEN again and you can turn projector on. After cooling down

completely, disconnect AC Power Cord.

Message disappears after 4 seconds.

TO MAINTAIN LIFE OF LAMP, ONCE YOU TURN

PROJECTOR ON, WAIT AT LEAST 5 MINUTES BEFORE

TURNING IT OFF.

When “Power Management” function is ON, projector detects signal interruption and turns off Projection Lamp automatically.

Refer to “Power Management” on page 35.

When WARNING TEMP. Indicator flashes red, projector is automatically turned off. Wait at least 5 minutes before turning on

projector again.

When WARNING TEMP. Indicator continues to flash, follow procedures below:

1. Press POWER ON-OFF button to turn a projector off and disconnect AC Power Cord from an AC outlet.

2. Check Air Filters for dust accumulation.

3. Clean Air Filters. (See "AIR FILTER CARE AND CLEANING" section on page 38.)

4. Turn a projector on again.

If WARNING TEMP. Indicator should still continue to flash, call Boxlight Corporation at 1-800-762-5757 or 360-779-7901.

Download from Www.Somanuals.com. All Manuals Search And Download.

BASIC OPERATION

ADJUSTING SCREEN

ZOOM ADJUSTMENT

Press ZOOM button on Top Control or ZOOM ●/● button on

Remote Control Unit. Message “Zoom” is displayed.

Press ZOOM ● button or POINT UP button to make image

larger, and press ZOOM ● button or POINT DOWN button to

make image smaller.

Zoom

Message disappears after 4 seconds.

FOCUS ADJUSTMENT

Press FOCUS button on Top Control or FOCUS ●/● button on

Remote Control Unit. Message “Focus” is displayed.

Adjust focus of image by pressing FOCUS ●/● button or

POINT UP/DOWN button(s) .

Focus

NOTE;

Focus adjustment may not function properly if the image is

corrected by KEYSTONE adjustment.

Message disappears after 4 seconds.

LENS SHIFT ADJUSTMENT

Press LENS SHIFT button on Top Control or LENS SHIFT ●/●

button on Remote Control Unit. Message “Lens shift” is

displayed.

Press POINT UP button or LENS SHIFT ● button to move

image up, press POINT DOWN or LENS SHIFT ● button to

move image down.

Lens shift

KEYSTONE ADJUSTMENT

If a projected picture has keystone distortion, correct the image with KEYSTONE adjustment.

Press KEYSTONE button on Remote Control Unit or select

Keystone on SETTING menu. (Refer to page 35.) Keystone

dialog box appears.

Correct keystone distortion by pressing POINT

UP/DOWN/LEFT/RIGHT button(s). Press POINT UP button to

reduce the upper part of the image, and press POINT DOWN

button to reduce the lower part. Press POINT LEFT button to

reduce the left part, and press POINT RIGHT button to reduce

the right part.

• Arrows are white in no correction.

• Arrow(s) of direction being corrected turn(s) red.

• Arrow(s) disappear(s) at the maximum

correction.

Reduce the upper width

with POINT UP button.

Reduce the lower width

with POINT DOWN button.

Reduce the left part with

POINT LEFT button.

Reduce the right part with

POINT RIGHT button.

Download from Www.Somanuals.com. All Manuals Search And Download.

BASIC OPERATION

PICTURE FREEZE FUNCTION

Press FREEZE button on Remote Control Unit to freeze picture on-screen. To cancel FREEZE function, press FREEZE

button again or press any other button except POINT / SELECT / RIGHT CLICK / LASER button.

NO SHOW FUNCTION

Press NO SHOW button on Remote Control Unit to black out image.

No show

To restore to normal, press NO SHOW button again or press any

other button except POINT / SELECT / RIGHT CLICK / LASER button.

Message disappears after 4 seconds.

P-TIMER FUNCTION

Press P-TIMER button on Remote Control unit. Timer display “00 : 00”

appears on screen and timer starts to count time (00 : 00 ~ 59 : 59).

To stop P-TIMER display, press P-TIMER button. And then, press P-

TIMER button again to cancel P-TIMER function.

SOUND ADJUSTMENT

Indicates roughly level of

volume.

DIRECT OPERATION

Volume

Press VOLUME (+/–) button(s) on Top Control or on Remote Control

Unit to adjust volume. Volume dialog box appears on screen for a few

seconds.

(+) button to increase volume, and (–) button for decreasing.

Mute

Press MUTE button to set

Mute function On or Off.

Press MUTE button on Remote Control Unit to cut off sound. To

restore sound to its previous level, press MUTE button again or press

Volume (+/–) button(s).

Display disappears after 4 seconds.

MENU OPERATION

Press MENU button and ON-SCREEN MENU will appear. Press

POINT LEFT/RIGHT buttons to move a red frame pointer to

SOUND Menu icon.

SOUND MENU

Press POINT DOWN button to move a red frame pointer to item

that you want to select, and then press SELECT button.

SOUND Menu icon

Indicates roughly

level of volume.

Volume

To increase volume, press POINT RIGHT button, and press POINT

LEFT button for decreasing.

Close SOUND Menu.

Mute

Press POINT LEFT/RIGHT button(s) to cut off sound. Dialog box

display is changed to “On” and sound is cut off. To restore sound to

its previous level, press POINT LEFT/RIGHT button(s) again.

Download from Www.Somanuals.com. All Manuals Search And Download.

COMPUTER INPUT

SELECTING INPUT SOURCE

INPUT button

Input 1

DIRECT OPERATION

Choose Computer by pressing INPUT button on Top Control or on

Remote Control Unit.

If projector cannot reproduce proper image, select correct input source

through MENU OPERATION (see below).

Input 2

Input 3

MENU OPERATION

Press MENU button and ON-SCREEN MENU will appear. Press

POINT LEFT/RIGHT buttons to select Input and press SELECT

button.

Menu will appear.

Another dialog box INPUT SELECT

INPUT Menu icon

Press POINT DOWN button and a red-arrow icon will appear.

Move arrow to INPUT source that you want to select, and then

press SELECT button.

SELECTING COMPUTER SYSTEM

WHEN SELECT INPUT 1 (COMPUTER INPUT TERMINALS )

INPUT MENU

Press MENU button and ON-SCREEN MENU will appear. Press

POINT LEFT/RIGHT button to move a red frame pointer to

INPUT Menu icon.

INPUT Menu icon

Press POINT DOWN button to move a red arrow pointer to Input

1 and then press SELECT button. Source Select Menu will

appear.

Move a pointer (red arrow) to

Input 1 and press SELECT

button.

Move a pointer to either Digital or Analog and then press

SELECT button.

Input 1

Source Select Menu

When your computer is connected to COMPUTER

INPUT (DIGITAL) terminal, select RGB (Digital).

Move a pointer to Digital or

Analog and press SELECT

button.

Digital

When your computer is connected to COMPUTER INPUT

(ANALOG) terminal, select RGB (Analog).

Analog

WHEN SELECT INPUT 2 (5 BNC INPUT JACKS )

When connect a computer output [5 BNC Type (Green, Blue, Red,

Horiz. Sync and Vert. Sync.)] from a computer to G, B, R, H/HV and V

jacks.

INPUT MENU

INPUT Menu icon

Press MENU button and ON-SCREEN MENU will appear. Press

POINT LEFT/RIGHT button to move a red frame pointer to

INPUT Menu icon.

Move a pointer (red arrow) to

Input 2 and press SELECT

button.

Press POINT DOWN button to move a red arrow pointer to Input

2 and then press SELECT button. Source Select Menu will

appear.

Input 2

Source Select Menu

Press POINT DOWN button and a red-arrow icon will appear.

Move arrow to "RGB", and then press SELECT button.

Move a pointer to RGB and

press SELECT button.

Download from Www.Somanuals.com. All Manuals Search And Download.

COMPUTER INPUT

AUTOMATIC MULTI-SCAN SYSTEM

This projector automatically tunes to most different types of computers based on VGA, SVGA, XGA or SXGA (refer to

“COMPATIBLE COMPUTER SPECIFICATION” on page 26). When selecting Computer, this projector automatically tunes

to incoming signal and projects proper image without any special setting. (Some computers need setting manually.)

Note : Projector may display one of following messages.

When projector cannot recognize connected signal as PC

system provided in this projector, Auto PC Adjustment

function operates to adjust projector and message “Auto”

is displayed on SYSTEM Menu icon.

PC SYSTEM MENU

Auto

When image is not provided properly, manual adjustment

is required. (Refer to P24 and 25.)

PC SYSTEM Menu icon

Displays system being

selected.

There is no signal input from computer. Make sure

connection of computer and a projector is set correctly.

(Refer to TROUBLESHOOTING on page 40.)

––––

D-VGA, D-SVGA or D-XGA

When digital computer signal is received on DVI terminal,

above message is displayed on PC SYSTEM Menu icon.

PC SYSTEM MENU

SELECT COMPUTER SYSTEM MANUALLY

This projector automatically selects PC system among those provided

in this projector and PC system can be also selected manually.

PC SYSTEM Menu icon

Displays system being selected.

Press MENU button and ON-SCREEN MENU will appear. Press

POINT LEFT/RIGHT buttons to move a red frame pointer to PC

SYSTEM Menu icon.

Systems on this dialog box can

be selected.

Press POINT DOWN button to move a red arrow pointer to

Custom Mode (1~5) set in PC

ADJUST Menu. (P24, 25)

system that you want to set, and then press

SELECT button.

PC ADJUSTMENT

AUTO PC ADJUSTMENT

Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots and Picture Position to conform to your

computer. Auto PC Adjustment function can be operated as follows.

Auto PC Adj.

Press MENU button and ON-SCREEN MENU will appear. Press

POINT LEFT/RIGHT button to move a red frame pointer to PC

ADJUST Menu icon.

PC ADJUST MENU

Press POINT DOWN button to move a red frame pointer to

AUTO PC Adj. icon and then press SELECT button twice.

This Auto PC Adjustment can be also executed by pressing

AUTO PC ADJ. button on Remote Control Unit.

PC ADJUST Menu icon

Move a red frame pointer to AUTO PC

Adj. icon and press SELECT button.

Store adjustment parameters.

Adjustment parameters from Auto PC Adjustment can be memorized

in this projector. Once parameters are memorized, setting can be

done just by selecting Mode in PC SYSTEM Menu (P23). Refer to

step 3 of MANUAL PC ADJUSTMENT section (P25).

NOTE

● Fine sync, Total dots and Picture Position of some computers can not be fully adjusted with this Auto PC Adjustment

function. When image is not provided properly through this function, manual adjustments are required. (Refer to page 24,

25.)

● Auto PC Adjustment function cannot be operated in Digital Signal input on DVI terminal and “RGB”, “720p (HDTV)”,

“1035i (HDTV)” or “1080i (HDTV)” is selected on PC SYSTEM Menu.

Download from Www.Somanuals.com. All Manuals Search And Download.

COMPUTER INPUT

MANUAL PC ADJUSTMENT

This projector can automatically tune to display signals from most personal computers currently distributed. However, some

computers employ special signal formats which are different from standard ones and may not be tuned by Multi-Scan system

of this projector. If this happens, projector cannot reproduce a proper image and image may be recognized as a flickering

picture, a non-synchronized picture, a non-centered picture or a skewed picture.

This projector has a Manual PC Adjustment to enable you to precisely adjust several parameters to match with those special

signal formats. This projector has 5 independent memory areas to memorize those parameters manually adjusted. This

enables you to recall setting for a specific computer whenever you use it.

Note : This PC ADJUST Menu cannot be operated when in digital signal input on DVI terminal and “RGB” is selected on PC

SYSTEM MENU (P23).

Press MENU button and ON-SCREEN MENU will appear. Press

POINT LEFT/RIGHT button to move a red frame pointer to PC

ADJUST Menu icon.

PC ADJUST MENU

Press POINT DOWN button to move a red frame pointer to item

that you want to adjust and then press SELECT button.

Adjustment dialog box will appear. Press POINT LEFT/RIGHT

button to adjust value.

PC ADJUST Menu icon

Move a red frame icon to item and press

SELECT button.

Fine sync

Adjusts an image as necessary to eliminate flicker from display.

Press POINT LEFT/RIGHT button to adjust value.(From 0 to 31.)

Shows status

Total dots

(Stored / Free) of

Selected Mode

selected Mode.

Number of total dots in one horizontal period. Press POINT

LEFT/RIGHT button(s) and adjust number to match your PC image.

Horizontal

Adjusts horizontal picture position. Press POINT LEFT/RIGHT

button(s) to adjust position.

Press POINT LEFT/RIGHT

button to adjust value.

Vertical

Adjusts vertical picture position. Press POINT LEFT/RIGHT

button(s) to adjust position.

Press SELECT button at this icon to

adjust “Clamp,” “Display area (H/V)” or

set “Full screen.”

Current mode

Press SELECT button to show information of computer selected.

Clamp

Current mode

Adjusts clamp position. When image has a dark bar(s), try this

adjustment.

Press SELECT button at

Current mode icon to show

information of computer

connected.

Download from Www.Somanuals.com. All Manuals Search And Download.

COMPUTER INPUT

Display area

Selects area displayed with this projector. Select resolution at

Display area dialog box.

Press SELECT button at

Display area icon and Display

area dialog box appears.

Display area H

Adjustment of horizontal area displayed with this projector. Press

POINT LEFT/RIGHT button(s) to decrease/increase value and then

press SELECT button.

Display area

Display area V

Adjustment of vertical area displayed with this projector. Press

POINT LEFT/RIGHT button(s) to decrease/increase value and then

press SELECT button.

Press POINT LEFT

/RIGHT button(s) to

adjust value and then

press SELECT button.

Full screen

Press POINT LEFT/RIGHT button(s) to switch Full screen function to

“On” or “Off.” Set “On” to resize image with 4 x 3 aspect ratio to fit

screen.

NOTE : Display area (H/V) and Full screen cannot be adjusted when

“1035i (HDTV)” or “1080i (HDTV)” is selected on PC

SYSTEM Menu (P23).

To store adjustment data.

This Mode has parameters being stored.

Store

To store adjustment parameters, move a red frame pointer to

Store icon and then press SELECT button. Move a red arrow

pointer to any of Mode 1 to 5 that you want to store and then

press SELECT button.

Mode free

To clear adjustment parameters previously set, move a red

frame pointer to Mode free icon and then SELECT button. Move

a red arrow pointer to Mode that you want to clear and then

press SELECT button.

Vacant Mode

Store icon

Shows values of “Total dots,”

“Horizontal,” “Vertical,” “Display

area H,” and “Display area V.”

Other icons operates as follows.

Reset

Reset all adjust parameters on adjustment dialog box to previous

figure.

To clear adjustment data.

Quit

Closes PC ADJUST MENU.

Close this dialog box.

Mode free icon

Download from Www.Somanuals.com. All Manuals Search And Download.

COMPUTER INPUT

COMPATIBLE COMPUTER SPECIFICATIONS

Basically this projector can accept a signal from all computers with V, H-Frequency mentioned below and less

than 160 MHz of Dot Clock.

ON-SCREEN

DISPLAY

H-Freq.

(kHz)

V-Freq.

(Hz)

ON-SCREEN

DISPLAY

H-Freq.

(kHz)

V-Freq.

(Hz)

RESOLUTION

VGA 1

VGA 2

VGA 3

VGA 4

VGA 5

VGA 6

VGA 7

MAC LC13

MAC 13

RGB

640 x 480

720 x 400

640 x 400

640 x 480

31.47

37.86

37.50

43.269

34.97

35.00

15.734

15.625

35.156

37.88

46.875

53.674

48.08

37.90

34.50

38.00

38.60

32.70

38.00

49.72

48.36

68.677

60.023

56.47

60.31

48.50

44.00

63.48

36.00

59.88

70.09

74.38

72.81

75.00

85.00

66.60

66.67

XGA 10

XGA 11

XGA 12

XGA 13

XGA 14

XGA15

1024 x 768

62.04

61.00

35.522

46.90

47.00

58.03

60.24

68.68

64.20

62.50

63.90

63.34

63.74

71.69

81.13

63.98

79.976

60.00

61.20

71.40

50.00

63.37

76.97

61.85

46.43

63.79

75.00

80.00

45.00

33.75

77.07

75.70

43.48

58.20

58.30

72.0

1024 x 768

(Interlace)

1024 x 768

1152 x 870

1152 x 864

1280 x 1024

1280 x 960

1152 x 900

MAC 19

MAC 21

SXGA 1

SXGA 2

SXGA 3

SXGA 4

SXGA 5

SXGA 6

SXGA 7

SXGA 8

SXGA 9

SXGA 10

SXGA 11

SXGA 12

SXGA 13

SXGA 14

75.08

75.06

70.40

58.60

60.00

59.98

60.01

67.19

76.107

60.02

75.025

60.00

65.20

75.60

43.00

47.00

60.01

72.00

66.00

43.35

60.18

75.08

60.00

30.00

––––––––

(Interlace)

––––––––

(Interlace)

RGB

SVGA 1

SVGA 2

SVGA 3

SVGA 4

SVGA 5

SVGA 6

SVGA 7

SVGA 8

SVGA 9

SVGA 10

SVGA 11

MAC 16

XGA 1

XGA 2

XGA 3

XGA 4

XGA 5

XGA 6

XGA 7

XGA 8

XGA 9

800 x 600

832 x 624

1024 x 768

56.25

60.32

75.00

85.06

72.19

61.03

55.38

60.51

60.31

51.09

60.51

74.55

60.00

84.997

75.03

70.07

74.92

60.02

54.58

79.35

43.59

1280 x 1024

(Interlace)

1280 x 1024

(Interlace)

SXGA 15 1280 x 1024

SXGA 16 1280 x 1024

SXGA 17

SXGA 18

1152 x 900

1280 x 1024

(Interlace)

SXGA 19 1280 x 1024

MAC

720p (HDTV)

1035i (HDTV)

1080i (HDTV)

1280 x 960

1280 x 1024

––––––––

(Progressive)

––––––––

(Interlace)

1024 x 768

(Interlace)

––––––––

(Interlace)

When a input signal is digital from DVI terminal, refer to chart below.

ON-SCREEN

DISPLAY

H-Freq.

(kHz)

V-Freq.

(Hz)

ON-SCREEN

DISPLAY

H-Freq.

(kHz)

V-Freq.

(Hz)

RESOLUTION

D-VGA

640 x 480

800 x 600

31.469

37.879

59.940

60.317

D-XGA

1024 x 768

48.363

60.004

D-SVGA

NOTE : Specifications are subject to change without notice.

Download from Www.Somanuals.com. All Manuals Search And Download.

COMPUTER INPUT

PICTURE IMAGE ADJUSTMENTS

IMAGE LEVEL SELECT (DIRECT)

Select image level among Standard, Real, Image 1, Image 2, Image 3

IMAGE button

and Image 4 by pressing IMAGE button on Top Control or on Remote

Control Unit.

Standard

Real

Standard

Normal picture level preset on this projector.

Image 1

Image 2

Image 3

Image 4

Real

Picture level with improved halftone for graphics.

IMAGE 1~4

User preset picture adjustment in IMAGE ADJUST Menu (P28).

IMAGE LEVEL SELECT (MENU)

Press MENU button and ON-SCREEN MENU will appear. Press

POINT LEFT/RIGHT button to move a red frame pointer to

IMAGE SELECT Menu icon.

IMAGE SELECT MENU

Press POINT DOWN button to move a red frame pointer to level

that you want to set and then press SELECT button.

IMAGE SELECT

Menu icon

Standard

Normal picture level preset on this projector.

Move a red frame icon to level and

press SELECT button.

Real

Picture level with improved halftone for graphics.

IMAGE 1~4

Level being selected.

User preset picture adjustment in IMAGE ADJUST Menu (P28).

Download from Www.Somanuals.com. All Manuals Search And Download.

COMPUTER INPUT

IMAGE LEVEL ADJUSTMENT

Press MENU button and ON-SCREEN MENU will appear. Press

POINT LEFT/RIGHT buttons to move a red frame pointer to

IMAGE ADJUST Menu icon.

IMAGE ADJUST MENU

Press POINT DOWN button to move a red frame pointer to item

that you want to adjust and then press SELECT button. Level of

each item is displayed. Adjust each level by pressing POINT

LEFT/RIGHT button(s).

IMAGE ADJUST

Menu icon

Move a red frame pointer to

item to be selected and then

press SELECT button.

Contrast

Press POINT LEFT button to decrease contrast, and POINT RIGHT

button to increase contrast. (From 0 to 63.)

Brightness

Press POINT LEFT button to adjust image darker, and POINT

RIGHT button to adjust brighter. (From 0 to 63.)

Selected Image level

White balance (Red)

Press POINT LEFT button to lighten red tone and POINT RIGHT

button to deeper tone. (From 0 to 63.)

White balance (Green)

Press POINT LEFT/RIGHT buttons

to adjust value.

Press POINT LEFT button to lighten green tone and POINT RIGHT

button to deeper tone. (From 0 to 63.)

White balance (Blue)

Press POINT LEFT button to lighten blue tone and POINT RIGHT

button to deeper tone. (From 0 to 63.)

Store icon

Press SELECT button at this icon to

store adjustment.

Gamma

Press either POINT LEFT button or POINT RIGHT button to obtain

better balance of contrast. (From 0 to 15.)

Store

To store manually preset image, move a red frame pointer to

Store icon and press SELECT button. Image Level Menu will

appear. Move a red frame pointer to Image 1 to 4 where you

want to set and then press SELECT button.

Image Level Menu

Other icons operates as follows.

Move a red frame pointer to any

of Image 1 to 4 where you want

to set and then press SELECT

button.

Reset

Reset all adjustment to previous figure.

Quit

Closes IMAGE MENU.

Download from Www.Somanuals.com. All Manuals Search And Download.

COMPUTER INPUT

PICTURE SCREEN ADJUSTMENT

This projector has a picture screen resize function, which enables you to display desirable image size.

Press MENU button and ON-SCREEN MENU will appear. Press

POINT LEFT/RIGHT button(s) to move a red frame pointer to

SCREEN Menu icon.

SCREEN MENU

Press POINT DOWN button and move a red frame pointer to

function that you want to select and then press SELECT button.

SCREEN Menu icon

Move red frame to function and press

SELECT button.

Normal

Provides image to fit screen size.

True

Provides image in its original size. When original image size is larger

than screen size (1024 x 768), this projector enters “Digital zoom +”

mode automatically.

NOTE

● True and Digital zoom +/– cannot be operated

when “RGB”, “1035i (HDTV)” or “1080i (HDTV)” is

selected on PC SYSTEM Menu (P23).

Wide

● Wide cannot be selected when “720p (HDTV)”,

“1035i (HDTV)” or “1080i (HDTV)” is selected on

PC SYSTEM Menu (P23).

Provides image to fit wide video aspect ratio (16 : 9) by expanding

image width uniformly. This function can be used for providing a

squeezed video signal at 16 : 9.

● This projector cannot display any resolution higher

than 1280 X 1024. If your computer’s screen

resolution is higher than 1280 X 1024, reset

resolution to lower before connecting projector.

Digital zoom +

When Digital zoom + is selected, ON-SCREEN MENU disappears

and message “D. Zoom +” is displayed. Press SELECT button to

expand image size. And press POINT UP/DOWN/LEFT/RIGHT

button(s) to pan image. Panning function can work only when image

is larger than screen size.

A projected image can be also expanded by pressing D.ZOOM ●

button on Remote Control Unit.

● Image data in other than XGA (1024 x 768) is

modified to fit screen size in initial mode.

● Panning function may not operate properly if

computer system prepared on PC ADJUST Menu

is used.

Digital Zoom –

When Digital zoom – is selected, ON-SCREEN MENU disappears

and message “D. Zoom –” is displayed. Press SELECT button to

compress image size.

A projected image can be also compressed by pressing D.ZOOM ●

button on Remote Control Unit.

To cancel Digital Zoom +/– mode, press any button except D.ZOOM

●/●, SELECT, POINT and AUTO PC ADJ. buttons.

Download from Www.Somanuals.com. All Manuals Search And Download.

VIDEO INPUT

SELECTING INPUT SOURCE

WHEN SELECT INPUT 2 (5 BNC INPUT JACKS )

When connecting to those equipment, select a type of Video

source in SOURCE SELECT Menu.

INPUT MENU

INPUT Menu icon

Press MENU button and ON-SCREEN MENU will appear. Press

POINT LEFT/RIGHT button to move a red frame pointer to

INPUT Menu icon.

Move a pointer (red arrow) to

Input 2 and press SELECT

button.

Press POINT DOWN button to move a red arrow pointer to Input

2 and then press SELECT button. Source Select Menu will

appear.

Input 2

Source Select Menu

Move a pointer to Video or

Y, Pb/Cb, Pr/Cr and press

SELECT button.

Move a pointer to source that you want to select and then press

SELECT button.

When video input signal is connected to VIDEO jack,

select Video.

Video

When video input signal is connected to Y-Pb/Cb-

Pr/Cr jacks, select Y, Pb/Cb, Pr/Cr.

Y,Pb/Cb,Pr/Cr

WHEN SELECT INPUT 3 (AV TERMINALS )

INPUT MENU

When connecting to those equipment, select a type of Video

source in SOURCE SELECT (VIDEO) Menu.

INPUT Menu icon

Press MENU button and ON-SCREEN MENU will appear. Press

POINT LEFT/RIGHT button to move a red frame pointer to

INPUT Menu icon.

Move a pointer (red arrow) to

Input 3 and press SELECT

button.

Press POINT DOWN button to move a red arrow pointer to Input

3 and then press SELECT button. Source Select Menu will

appear.

Input 3

Source Select Menu (VIDEO)

Move a pointer to source

and press SELECT button.

Move a pointer to source that you want to select and then press

SELECT button.

When video input signal is connected to VIDEO jack,

select Video.

Video

When video input signal is connected to Y-Pb/Cb-

Pr/Cr jacks, select Y, Pb/Cb, Pr/Cr.

Y,Pb/Cb,Pr/Cr

When video input signal is connected to S-VIDEO jack,

select S-Video.

S-Video

Download from Www.Somanuals.com. All Manuals Search And Download.

VIDEO INPUT

SELECTING VIDEO SYSTEM

Press MENU button and ON-SCREEN MENU will appear. Press

POINT LEFT/RIGHT buttons to move a red frame pointer to AV

SYSTEM Menu icon.

Press POINT DOWN button to move a red arrow pointer to

system that you want to select and then press SELECT button.

VIDEO JACK OR S-VIDEO JACK

AV SYSTEM MENU (VIDEO OR S-VIDEO)

Auto

Projector automatically detects incoming Video system, and adjusts

itself to optimize its performance.

When Video System is PAL-M or PAL-N, select system manually first.

AV SYSTEM Menu icon

This box indicates system

being selected.

PAL / SECAM / NTSC / NTSC4.43 / PAL-M / PAL-N

If projector cannot reproduce proper video image, it is necessary to

select a specific broadcast signal format among PAL, SECAM, NTSC,

NTSC 4.43, PAL-M, and PAL-N.

Move pointer to system

and press SELECT

button.

Y, Pb/Cb, Pr/Cr JACKS

AV SYSTEM MENU (COMPONENT VIDEO)

Auto

Projector automatically detects incoming Video signal, and adjusts

itself to optimize its performance.

When Video System is 1035i or 1080i, select system manually first.

AV SYSTEM Menu icon

This box indicates system

being selected.

COMPONENT VIDEO SIGNAL FORMAT

If projector cannot reproduce proper video image, it is necessary to

select a specific component video signal format among 480i, 575i,

480p, 575p, 720p, 1035i and 1080i.

Move pointer to system

and press SELECT

button.

Download from Www.Somanuals.com. All Manuals Search And Download.

VIDEO INPUT

PICTURE IMAGE ADJUSTMENTS

IMAGE LEVEL SELECT (DIRECT)

Select image level among Standard, Cinema, Image 1, Image 2,

Image 3 and Image 4 by pressing IMAGE button on Top Control or on

Remote Control Unit.

IMAGE button

Standard

Cinema

Image 1

Image 2

Image 3

Image 4

Standard

Normal picture level preset on this projector.

Cinema

Picture level adjusted for picture with fine tone.

IMAGE 1~4

User preset picture adjustment in IMAGE ADJUST Menu (P34).

IMAGE LEVEL SELECT (MENU)

Press MENU button and ON-SCREEN MENU will appear. Press

POINT LEFT/RIGHT button to move a red frame pointer to

IMAGE SELECT Menu icon.

IMAGE SELECT MENU

Press POINT DOWN button to move a red frame pointer to level

that you want to set and then press SELECT button.

IMAGE SELECT

Menu icon

Standard

Normal picture level preset on this projector.

Cinema

Move red frame pointer to level

and press SELECT button.

Picture level adjusted for picture with fine tone.

IMAGE 1~4

Level being selected.

User preset picture adjustment in IMAGE ADJUST Menu (P34).

Download from Www.Somanuals.com. All Manuals Search And Download.

VIDEO INPUT

IMAGE LEVEL ADJUSTMENT

Press MENU button and ON-SCREEN MENU will appear. Press

POINT LEFT/RIGHT button(s) to move a red frame pointer to

IMAGE ADJUST Menu icon.

IMAGE ADJUST MENU

Press POINT DOWN button to move a red frame pointer to item

that you want to adjust and then press SELECT button. Level of

each item is displayed. Adjust each level by pressing POINT

LEFT/RIGHT button(s).

IMAGE ADJUST

Menu icon

Move a red frame pointer to

item to be selected and then

press SELECT button.

Contrast

Press POINT LEFT button to decrease contrast, and POINT RIGHT

button to increase contrast. (From 0 to 63.)

Brightness

Press POINT LEFT button to adjust image darker, and POINT

RIGHT button to adjust brighter. (From 0 to 63.)

Color

Press POINT LEFT button to lighten color, and POINT RIGHT button

to deeper color. (From 0 to 63.)

Press POINT LEFT/RIGHT buttons

to adjust value.

Tint

Press SELECT button at this icon to

display other items.

Press POINT LEFT button or POINT RIGHT button to obtain proper

color. (From 0 to 63.)

White balance (Red)

Press SELECT button at this icon to

display previous items.

Press POINT LEFT button to lighten red tone and POINT RIGHT

button to deeper tone. (From 0 to 63.)

White balance (Green)

Press POINT LEFT button to lighten green tone and POINT RIGHT

button to deeper tone. (From 0 to 63.)

Press POINT LEFT/RIGHT buttons

to adjust value.

White balance (Blue)

Press POINT LEFT button to lighten blue tone and POINT RIGHT

button to deeper tone. (From 0 to 63.)

Sharpness

Press POINT LEFT button to soften image, and POINT RIGHT

button to sharpen image. (From 0 to 15.)

Press SELECT button at this icon to

store value.

Gamma

Press either POINT LEFT button or POINT RIGHT button to obtain

better balance of contrast. (From 0 to 15.)

NOTE :

Tint cannot be adjusted when video system is PAL,

SECAM, PAL-M or PAL-N.

Noise reduction

Press POINT LEFT/RIGHT button(s) to change noise reduction mode.

Dialog box display is changed to “On” to reduce noise (rough parts) of

Noise Reduction cannot be operated when video

signal types and systems as follow.

image. Press POINT LEFT/RIGHT button(s) again, to change noise ●●Composite video signal (SECAM, NTSC4.43,

PAL-M and PAL-N systems).

reduction mode to off.

●●S-video signal (SECAM, PAL-M and PAL-N

Progressive scan

systems).

●●Component video signal.

Press POINT LEFT/RIGHT button(s) to change progressive scan

mode. Dialog box display is changed to “Off” and progressive scan

mode to off. Press POINT LEFT/RIGHT button(s) again, progressive

scan mode to on.

Progressive cannot be operated when “480p”,

“575p”, “720p”, “1035i” or “1080i” is selected on AV

SYSTEM MENU (P31).

Download from Www.Somanuals.com. All Manuals Search And Download.

VIDEO INPUT

Store

To store adjustment data, move a red frame pointer to Store icon

and press SELECT button. Image Level Menu will appear.

Move a red frame pointer to Image Level 1 to 4 and then press

SELECT button.

Image Level Menu

Other icons operates as follows.

Move a red frame pointer to

image icon to be set and

then press SELECT button.

Reset

Reset all adjustment to previous figure.

Quit

Store icon

Closes IMAGE MENU.

PICTURE SCREEN ADJUSTMENT

This projector has a picture screen resize function, which enables you to display desirable image size.

Press MENU button and ON-SCREEN MENU will appear. Press

POINT LEFT/RIGHT button(s) to move a red frame pointer to

SCREEN Menu icon.

SCREEN MENU

Press POINT DOWN button and move a red frame pointer to

function that you want to select and then press SELECT button.

SCREEN Menu icon

Move red frame to function and press

Normal

SELECT button.

Provides image at a normal video aspect ratio of 4 : 3.

NOTE : SCREEN Menu cannot be operated when

“720p,” “1035i,” or “1080i” is selected on AV

SYSTEM Menu (P31).

Wide

Provides image at a wide screen ratio of 16 : 9.

Download from Www.Somanuals.com. All Manuals Search And Download.

SETTING

SETTING MENU

Press MENU button and ON-SCREEN MENU will appear. Press

SETTING MENU

POINT LEFT/RIGHT button(s) to move a red-frame pointer to

SETTING icon.

Press POINT DOWN button to move a red-frame pointer to item

Set a red frame

SETTING Menu icon

that you want to set and then press

dialog box appears.

SELECT button. Setting

pointer to item and

press SELECT

button.

Language

Language used in ON-SCREEN MENU is selectable from among

English, German, French, Italian, Spanish, Portuguese, Dutch,

Swedish, Chinese, Korean and Japanese.

Keystone

When image is distorted, select Keystone. ON-SCREEN MENU

disappears and Keystone dialog box is displayed. Correct keystone

distortion by pressing POINT UP/DOWN/LEFT/RIGHT button(s).

Refer to KEYSTONE ADJUSTMENT on page 20.

When pressing SELECT

button at Language,

Language Menu appears.

Blue back

When this function is “On,” this projector will produce a blue image

instead of video noise on screen when any input source is unplugged

or turned off.

Display

This function decides whether to display On-Screen Displays.

On ··· shows all On-Screen Displays.

Off ···· sets On-Screen Displays disappeared except;

● ON-SCREEN MENU

● “Power off?” message

Logo

When this function is “On,” projector displays our logo when starting up.

Move a pointer to item and

then press POINT

Ceiling

LEFT/RIGHT button(s).

When this function is “On,” picture is top / bottom and left / right

reversed. This function is used to project image from a ceiling mounted

projector.

Ceiling function

Rear

When this function is “On,” picture is left / right reversed. This function is

used to project image to a rear projection screen.

Power management

This function turns Projection Lamp off when this projector detects

signal interruption and is not used for a certain period in order to

reduce power consumption and maintain Lamp-life. (This projector is

shipped with this function ON.)

Rear function

Power Management function operates to turn Projection Lamp off

when input signal is interrupted and any button is not pressed over 5

minutes. This function operates as follows;

1. When any input signal is interrupted, “No signal” and counting

down display appears (for 5 minutes).

2. After counting down for 5 minutes, projector lamp and READY

indicator are turned off.

3. When READY indicator flashing, Projection Lamp can be turned

on again (Power Management mode).

In this Power Management mode, Projection Lamp is

automatically turned on when input signal connected or projector

is operated with any button on Top Control or on Remote Control

Unit again.

Time left until Lamp off.

Download from Www.Somanuals.com. All Manuals Search And Download.

SETTING

On start

When this function is “On,” projector is automatically turned on just

by connecting AC Power cord to a wall outlet.

Note ; Be sure to turn projector off properly (refer to section

“TURNING OFF PROJECTOR” on P19). If projector is turned

off in wrong steps, On Start function does not operate

properly.

Lamp mode

When selecting the

and set into the low power consumption mode.

(Eco), the projector reduce the brightness

Press SELECT button at this icon to

display other items.

Remote control

This projector has two different remote control codes; factory-set

normal code (Code 1) and secondary code (Code 2). This switching

function prevents remote control operation mixture (jam) when

operating several projectors or video equipment together.

When operating projector in “Code 2,” both projector and Remote

Control Unit must be switched to “Code 2.”

On start

To change code of Projector;

Press SELECT button at this icon to

display previous items.

Set Remote control in SETTING MENU to “Code 2.”

To change code of Remote Control Unit;

Press both MENU and IMAGE buttons on Remote Control Unit

together for over 10 seconds.

Move pointer to item and then press

POINT LEFT/RIGHT button(s).

After changing code, make sure Remote Control operates properly.

To return to normal code (Code 1), operate both projector and

Remote Control in ways above again.

NOTE : When batteries of Remote Control Unit are replaced or ALL-

OFF switch is turned to “ALL-OFF,” remote transmit code

automatically returns to normal code (Code 1).

USB

This Projector is equipped with USB port for interactive operation

between a projector and computer. Set mode following steps below.

Wireless Mouse mode

Select "

" when controlling a computer with Remote Control of

this projector.

Projector mode

Select "

" when controlling a projector with computer.

NOTE: Before you control a projector by computer, install USB driver

(optionally sold parts) and set up computer following instruc-

tion in USB driver package. Contact your authorized dealer.

Network icon

This function cannot be adjusted when not attach the network option

to the projector.

Download from Www.Somanuals.com. All Manuals Search And Download.

SETTING/APPENDIX

Lamp counter reset

Lamp

counter reset

This function is used to reset Lamp Replace Counter. When

replacing Projection Lamp, reset Lamp Replace Counter by using

this function. Refer to page 39 for operation.

Quit

Closes SETTING MENU.

Move pointer to Lamp counter reset and then press

SELECT button. Message “Lamp replace counter

reset?” is displayed.

OPERATING WIRELESS MOUSE

Wireless Remote Control Unit is not only able to operate this projector but also usable as a wireless mouse for most

Personal Computers. POINT buttons and two CLICK buttons are used for wireless mouse operation.

This Wireless Mouse function is available only when PC mouse pointer is displayed on a projected screen. When ON-

SCREEN MENU or any message / dialog box is displayed on screen instead of PC mouse pointer, this Wireless Mouse

function cannot be used.

INSTALLATION

To use Wireless Remote Control Unit as Wireless Mouse for a Personal Computer, installation of mouse driver (not supplied)

is required. Make sure that mouse driver is properly installed in your computer. And make sure that mouse port (or USB

port) of a Personal Computer is activated.

Connect mouse port (or USB port) of your computer to Control

Port (or USB connector) of this projector with Control Cable (or

USB cable). (Refer to page 11, 12 for connection.)

Note : When your computer has no mouse

port, connect Serial Port of your

computer to Control Port of a projector

with Control Cable for Serial Port (not

supplied).

Turn a projector on first, and then turn on your computer. When

computer is switched on first, Wireless Mouse may not work

properly.

OPERATING WIRELESS MOUSE

When controlling a PC mouse pointer, operate Wireless Mouse with POINT button, SELECT button, and RIGHT CLICK

button on Wireless Remote Control Unit.

POINT button

POINT button (Move pointer)

Used to move PC mouse pointer. Pointer is moved corresponding

with direction you are pressing.

SELECT (LEFT CLICK) button

This button has same function as left button in a PC mouse.

RIGHT CLICK button

This button has same function as right button in a PC mouse. This

button is not available for controlling this projector.

SELECT button

(left button of mouse)

RIGHT CLICK button

(right button of mouse)

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX

MAINTENANCE

WARNING TEMP. INDICATOR

WARNING TEMP. Indicator flashes red when an internal temperature of a projector exceeds normal temperature. This

Indicator stops flashing when temperature of a projector returns to normal.

When WARNING TEMP. Indicator continues to flash, check items listed below.

Ventilation Slots of a projector may be blocked. In such an event, reposition a projector so that Ventilation Slots are

not obstructed.

Air Filter may be clogged with dust particles. Clean Air Filter by following section AIR FILTER CARE AND CLEANING

below.

If WARNING TEMP. Indicator remains on after performing above checks, Cooling Fans or Internal Circuits may be

malfunctioning. Contact service personnel from an authorized dealer or a service station.

AIR FILTER CARE AND CLEANING

Air Filter prevents dust from accumulating on surface of Projection Lens and Projection Mirror. Should Air Filter become

clogged with dust particles, it will reduce Cooling Fans’ effectiveness and may result in internal heat build up and adversely

affect life of a projector. Clean Air Filter following steps below:

Turn off a projector, and disconnect AC power cord from AC

outlet.

Turn a projector upside down and remove Air Filter (2 used) by

pulling latches upward.

Clean Air Filter with a brush or wash out dust and particles.

Replace Air Filter properly. Make sure that Air Filter is fully

inserted.

CAUTION

Do not operate a projector with Air Filter removed. Dust

may accumulate on LCD Panel and Projection Mirror

degrading picture quality.

Do not put small parts into Air Intake Vents. It may result

in malfunction of a projector.

AIR FILTER

Pull up and remove.

RECOMMENDATION

We recommend avoiding dusty/smoky environments when operating a projector. Usage in these environments

may cause poor image quality.

When using under dusty or smoky conditions, dust may accumulate on a lens, liquid crystal panels, or optical elements

inside a projector. This condition may degrade quality of a projected image.

When above symptoms are noticed, contact a Boxlight Corporation at 1-800-762-5757 or 360-779-7901 for cleaning.

CLEANING PROJECTION LENS

Follow these steps to clean Projection Lens:

Apply a non-abrasive camera lens cleaner to a soft, dry cleaning cloth. Avoid using an excessive amount of cleaner.

Abrasive cleaners, solvents or other harsh chemicals might scratch a surface.

Lightly wipe a cleaning cloth over Projection Lens.

When a projector is not in use, replace Lens Cover.

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX

LAMP REPLACEMENT

When life of Projection Lamp of this projector draws to an end, LAMP REPLACEMENT indicator lights yellow. When a

projected image becomes dark or color of an image becomes unnatural, replacement of Projection Lamp is required.

CAUTION

For continued safety, replace with a lamp

Do not drop a lamp assembly or touch a glass

assembly of same type.

bulb! Glass can shatter and may cause injury.

Allow a projector to cool for at least 45

minutes before you open Lamp Cover. Inside

of a projector can become very hot.

Follow these steps to replace lamp assembly.

Turn off a projector and disconnect AC plug. Allow a projector to

cool for at least 45 minutes.

Loosen 2 screws with a screwdriver and open Lamp Cover.

Loosen 2 screws with a screwdriver and pull out Lamp Assembly

by grasping Handle.

LAMP COVER

Replace Lamp Assembly with a new one and tighten 2 screws

back. Make sure that Lamp Assembly is set properly. Replace

Lamp Cover and tighten 2 screws.

LAMP

ASSEMBLY

HANDLE

Connect AC Power Cord to a projector and turn it on.

Reset Lamp Replace Counter (refer to section “Lamp Replace

Counter” below).

NOTE : Do not reset Lamp Replace Counter when Projection

Lamp is not replaced.

ORDER REPLACEMENT LAMP

Replacement Lamp can be ordered through Boxlight Corporation at 1-800-762-5757 or 360-779-7901. When

ordering Projection Lamp, give following information to dealer.

● Model No. of your projector : BOXLIGHT MP-42t

● Replacement Lamp Type No. : MP42T-930

(Service Parts No. 610 297 3891)

LAMP REPLACE COUNTER

Be sure to reset Lamp Replace Counter when Lamp Assembly is replaced. When Lamp Replace Counter is reset, LAMP

REPLACE Indicator stops lighting.

Turn projector on, press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button(s) to

move a red frame pointer to SETTING Menu icon (refer to page 37).

Press POINT DOWN button to move a red frame pointer to “Lamp counter reset” and then press

Message "Lamp replace counter reset?" is displayed. Move pointer to [Yes] and then press SELECT button.

SELECT button.

Another confirmation dialog box appears and select [Yes] to reset Lamp Replace Counter.

Do not reset Lamp Replace Counter except after Projection Lamp is replaced.

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX

TROUBLESHOOTING

Before calling your dealer or service center for assistance, check matters below once again.

1. Make sure you have connected a projector to your computer or video equipment as described in section "CONNECTING

PROJECTOR" on pages 11 ~ 13.

2. Check cable connection. Verify that all computer, video and power cord are properly connected.

3. Verify that all power is switched on.

4. If a projector still does not produce an image, re-start your computer.

5. If an image still does not appear, unplug a projector from your computer and check your computer monitor's display.

Problem may be with your graphics controller rather than with a projector. (When you reconnect a projector, be sure to

turn computer and monitor off before you power up a projector. Power equipment back on in order of : Projector and

computer.)

6. If problem still exists, check following chart.

Problem:

No power.

Try these Solutions

● Plug a projector into your AC outlet.

● Make sure READY Indicator lights.

● Wait 90 seconds after a projector is turned OFF when turning a projector back on.

NOTE : After pressing Power ON-OFF button to OFF, make sure a projector works as

follows:

1. LAMP indicator lights bright and READY indicator turns off.

2. After 90 seconds, READY indicator lights green again and a projector may be

turned on by pressing Power ON-OFF button.

● Check WARNING TEMP. indicator. If indicator flashes red, a projector cannot be turned

on.

(See "TURNING ON/OFF PROJECTOR" section on page 19.)

● Check Projection Lamp. (Refer to page 39.)

● Adjust focus of a projector.

● Make sure a projection screen is at least 4.6’ (1.4m) from a projector.

● Check Projection Lens to see if it needs cleaning.

Image is out of

focus.

NOTE : Moving a projector from a cool temperature location to a warm temperature location

may result in moisture condensation on Projection Lens. In such an event, leave a

projector OFF and wait until condensation disappears.

● Check Ceiling / Rear feature. (See “SETTING” section on page 35.)

Picture is Left/Right

reversed.

● Check Ceiling feature. (See “SETTING” section on page 35.)

Picture is

Top/Bottom

reversed.

● Check Display feature.(See “SETTING” section on page 35.)

Some displays are

not seen during

Operation.

● Check connection between your computer or video equipment and a projector.

● When turning a projector on, it takes about 30 seconds to display an image.

● Check system that you select is corresponding with your computer or video equipment.

● Make sure temperature is not out of Operating Temperature (5°C ~ 35°C).

No image.

● Check audio cable connection from audio input source.

● Adjust audio source.

No sound.

● Press VOLUME (+) button.

● Press MUTE button.

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX

Problem:

Remote Control Unit

does not work.

Try these Solutions

● Check batteries.

● Check ALL-OFF switch on Remote Control Unit is set to “ON”.

● Make sure nothing is between Infrared Remote Receiver and Remote Control Unit.

● Make sure you are not too far from a projector when using Remote Control Unit.

Maximum operating range is 16.4’ (5m).

● Check transmitted signal mode from Remote Control Unit.

(See“SETTING” section on page 36.)

● Check cable connection between a projector and your computer.

● Check mouse setting on your computer.

● Turn a projector on before turning on a computer.

Wireless Mouse

function does not

work.

SERVICE

WARNING: High voltages are used to operate this projector. Do not attempt to open the cabi-

net.

Boxlight Service is easily obtained. If after following instructions above, you find that service is necessary, con-

tact Boxlight for assistance at 1-800-762-5757 or 360-779-7901.

Give the model number and explain the difficulty. We will advise you how to obtain service.

Please have the following information available:

●●Serial Number of Projector.

●●Resolution of Computer.

●●Refresh rate of Computer.

This symbol on the nameplate means the product is Listed by Underwriters

Laboratories Inc. It is designed and manufactured to meet rigid U.L. safety

standards against risk of fire, casualty and electrical hazards.

The CE Mark is a Directive conformity mark of the European Community (EC).

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX

TECHNICAL SPECIFICATIONS

Multi-media Projector

Projector Type

12.6" x 6.6" x 18.5" (319 mm x 168 mm x 470 mm)

18.5 lbs (8.4 kg)

(W x H x D)

Dimensions

Net Weight

1.3" TFT Active Matrix type, 3 panels

1024 x 768 dots

LCD Panel System

Panel Resolution

Number of Pixels

Color System

2,359,296 (1024 x 768 x 3 panels)

PAL, SECAM, NTSC, NTSC4.43, PAL-M and PAL-N

480i, 480p, 575i, 575p, 720p, 1035i and 1080i

H-sync. 15 ~ 100 KHz, V-sync. 50 ~ 100 Hz

F1.7 ~ 2.0 lens with f=48.2 mm ~ 62.6 mm Motor zoom and focus

4.6' (1.4 m) ~ 48.3' (14.7 m)

High Definition TV Signal

Scanning Frequency

Projection Lens

Throw distance

Up and Down

Motorized Lens Shift

Projection Image Size (Diagonal)

Horizontal Resolution

Projection Lamp

Input 1 Jacks

Adjustable from 31" to 400"

800 TV lines (HDTV)

275 watt type

DVI Terminal (Digital), HDB 15-pin Terminal (Analog)

and Stereo Mini Type Jack (Audio)

BNC Type x 5 (G or VIDEO/Y, B or Cb/Pb, R or Cr/Pr, H and V), Stereo Mini

Type Jack (Audio)

Input 2 Jacks

Input 3 Jacks

RCA Type x 3 (VIDEO/Y, Cb/Pb and Cr/Pr), RCA Type x 2 (Audio R and L)

and DIN 4-pin (S-Video)

DIN 8-pin (Control port), USB port (Series B receptacle) and Wired Remote Jack

INT. SP. Stereo (R and L), 2 watt RMS (T.H.D. 10%)

0˚ to 10.5˚

Other Jack

Built-in Speakers

Feet Adjustment

Voltage and

Power Consumption

Operating Temperature

AC 100 ~ 120 V (4.8 A Max. Ampere), 50 / 60 Hz (The U.S.A and Canada)

AC 200 ~ 240 V (2.4 A Max. Ampere), 50 / 60 Hz (Continental Europe)

41 ˚F ~ 95 ˚F (5 ˚C ~ 35 ˚C)

14 ˚F ~ 140 ˚F (-10 ˚C ~ 60 ˚C)

Storage Temperature

Power Source

Operating Range

Dimensions

Net Weight

Laser Pointer

AA, UM3 or R06 Type x 2

16.4’ (5m) / ±30˚

2.2” x 1.3” x 7.6” (55mm x 34mm x 192mm)

0.36 lbs (165 g) (including batteries)

(Max. Output : 1mW / Wave length : 650±20nm)

Class II Laser

Remote Control Transmitter

User’s Guide

Accessories

AC Power Cord

Wireless/Wired Remote Control Transmitter and Batteries

Remote Control Cable

VGA Cable

MAC/VGA Adapter

3 Types Control Cable (For PS/2, Serial and ADB port)

Protective Dust Cover

Lens Cover

● Specifications are subject to change without notice.

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX

CONFIGURATIONS OF TERMINALS

COMPUTER INPUT-1 TERMINAL (ANALOG)

Terminal : HDB15-PIN

Connect display output terminal of computer to this terminal with VGA Cable (supplied). When connecting Macintosh

computer, MAC Adapter (supplied) is required.

Red Input

Green Input

Blue Input

Sense 2

+5V Power

Pin Configuration

10 Ground (Vert.sync.)

11 Sense 0

12 DDC Data

Ground (Horiz.sync.) 13 Horiz. sync.

Ground (Red)

Ground (Green)

Ground (Blue)

14 Vert. sync.

15 DDC Clock

COMPUTER INPUT-1 TERMINAL (DIGITAL)

Terminal : DVI 24-pin

Connect display output terminal of computer to this terminal with DVI cable (for Single Link T.M.D.S. / not supplied).

T.M.D.S. Data2–

T.M.D.S. Data1–

17 T.M.D.S. Data0–

18 T.M.D.S. Data0+

Pin Configuration

T.M.D.S. Data2+

10 T.M.D.S. Data1+

T.M.D.S. Data2 Shield 11 T.M.D.S. Data1 Shield 19 T.M.D.S. Data0 Shield

No Connect

DDC Clock

DDC Data

12 No Connect

13 No Connect

14 +5V Power

20 No Connect

10 11 12 13 14 15 16

17 18 19 20 21 22 23 24

21 No Connect

22 T.M.D.S. Clock Shield

23 T.M.D.S. Clock+

24 T.M.D.S. Clock–

15 Ground (for +5V)

16 Hot Plug Detect

No Connect

CONTROL PORT CONNECTOR

Terminal : Mini DIN 8-PIN

Connect control port (PS/2, Serial or ADB port) on your computer to this connector with Control Cable (supplied).

PS/2

-----

Serial

R X D

-----

ADB

-----

Pin Configuration

CLK

DATA

GND

-----

ADB

-----

GND

-----

RTS / CTS

T X D

GND

-----

GND

-----

GND

USB CONNECTOR (Series B)

Connect USB port terminal on your computer or peripheral equipment to this connector with USB Cable (not supplied).

Pin Configuration

Vcc

- Data

+ Data

Ground

Download from Www.Somanuals.com. All Manuals Search And Download.

LIMITED WARRANTY

BOXLIGHT CORPORATION ("BOXLIGHT") warrants that each Boxlight MP-42t ("the Product") sold hereunder will con-

form to and function in accordance with the written specifications of BOXLIGHT. Said limited warranty shall apply only to

the first person or entity that purchases the Product for personal or business use and not for the purpose of distribution or

resale. Said warranty shall continue for a period of two (2) years from the date of such purchase. BOXLIGHT does not

warrant that the Product will meet the specific requirements of the first person or entity that purchases the Product for

personal or business use. Lamp is warrantied for 120 days.

BOXLIGHT CORPORATION's liability for the breach of the foregoing limited warranty is limited to the repair or replace-

ment of the Product or refund of the purchase price of the Product, at BOXLIGHT's sole option. To exercise the

Purchaser's rights under the foregoing warranty, the Product must be returned at the Purchaser's sole cost and expense,

to BOXLIGHT or any authorized service center provided, however, that the Product must be accompanied by a written

letter explaining the problem and which includes (i) proof of purchase; (ii) the dealer's name; and (iii) the model and serial

number of the Product. A return authorization number, issued by the BOXLIGHT customer service department, must also

be clearly displayed on the outside of the shipping carton containing the Product.

WARRANTY LIMITATION AND EXCLUSION

BOXLIGHT CORPORATION shall have no further obligation under the foregoing limited warranty if the Product has been

damaged due to abuse, misuse, neglect, accident, unusual physical or electrical stress, unauthorized modification, tam-

pering, alterations, or service other than by BOXLIGHT or its authorized agents, causes other than from ordinary use or

failure to properly use the Product in the application for which said Product is intended.

DISCLAIMER OR UNSTATED WARRANTIES

The warranty printed above is the only warranty applicable to this purchase.

All other warranties express or implied, including, but not limited to, the implied warranties or merchantability and fitness

for a particular purpose are disclaimed. There are no warranties that extend beyond the face hereof and the foregoing

warranty shall not be extended, altered or varied except by written instrument signed by BOXLIGHT CORPORATION.

LIMITATION OR LIABILITY

It is understood and agreed that BOXLIGHT's liability whether in contract, in tort, under any warranty, in negligence or

otherwise shall not exceed the return of the amount of the purchase price paid by purchaser and under no circumstances

shall BOXLIGHT be liable for special, indirect or consequential damages. The price stated for the Product is a considera-

tion in limiting BOXLIGHT's liability. No action regardless of form, arising out of the agreement to purchase the product

may be brought by purchaser more than one year after the cause of action has accrued.

Boxlight

19332 Powder Hill Place

Poulsbo, WA 98370-7407 USA

www.boxlight.com

U.S. and Canada 800-762-5757

International 1-360-779-7901

Printed in Japan

Part No. 610 297 8360 (1AA6P1P3142-- MA8EA)

Download from Www.Somanuals.com. All Manuals Search And Download.

Belkin Laptop Docking Station F5U216 User Manual
Bernina Sewing Machine Stitch Regulator User Manual
Black Decker Sander 90549547 User Manual
Briggs Stratton Air Cleaner 445600 User Manual
Campbell Hausfeld Air Compressor IN620100AV10 User Manual
Canon Camera Lens 11 24mm f 4L User Manual
Casio Electronic Keyboard WK 1500 User Manual
Century Car Seat ISPB009BA User Manual
Chauvet Work Light Arena Hazer 3 User Manual
Cisco Systems Network Card 3545 Serial User Manual