Behringer Car Amplifier PP400 User Manual

MICROPHONO PP400  
(4) OUTPUT (L and R) connectors:  
Welcome to BEHRINGER  
Thank you for showing your confidence in us by purchasing the BEHRINGER MICROPHONO  
PP400, a compact phono preamplifier.  
To use these RCA connectors, you need an RCA audio cable (stereo). Use this audio  
cable to connect:  
the L (left) OUTPUT on the PP400 to the left input on the amplifier,  
recording unit, or mixer. (On a mixer, use a CD or TAPE input.)  
the R (right) OUTPUT on the PP400 to the right input on the amplifier,  
recording unit, or mixer  
Turntables have low-level signals. However, most audio units can only process line-level  
signals. Between a turntable and another audio unit (a mixer, an amplifier, or a recording  
unit), the PP400 acts as an intermediary, as follows:  
1. The PP400 equalizes a turntable signal according to RIAA specifications.  
2. The PP400 amplifies the RIAA equalized signal.  
3. The PP400 outputs a line-level signal.  
(5) OUTPUT connector:  
To use this ¼”, TRS (stereo) connector, you need an audio cable. Use the audio cable  
to connect the PP400 OUTPUT to an input on the mixer, amplifier, or recording unit.  
One end of this audio cable must include a ¼”, TRS connector. If the input on the mixer,  
amplifier, or recording unit is:  
Please read the safety instructions that appear at the end of this document.  
Connectors and Control Elements  
This section illustrates and describes each PP400 connector and control element.  
stereo, the other end of the audio cable must include a ¼”, TRS connector  
mono, the other end of the audio cable must include 2 TS connectors  
(one for each mono input)  
(1)  
(3)  
(4)  
(5)  
SERIAL NUMBER: To register your unit, use the serial number that is located on the bottom  
of the PP400.  
Setup Example  
The following is an example of how to set up the PP400:  
(2)  
Fig. 1: PP400 connectors and control elements  
(1) 12 Vconnector:  
To connect the power supply unit to the PP400, use the 12 V connector. Connecting the  
power supply unit to the mains automatically switches the PP400 on. To disconnect  
the unit from the mains, pull out the main cord plug.  
(2) ON LED:  
As soon as the unit is connected to the mains, the ON LED is illuminated.  
(3) INPUT (L and R) connectors:  
To send a turntable signal to the PP400, you need an RCA audio cable (stereo). Use this  
cable to connect:  
the left output on the turntable to the L (left) INPUT on the PP400  
the right output on the turntable to the R (right) INPUT on the PP400  
The PP400 can output a line-level signal via one of the following connectors:  
Fig 2: PP400 setup example  
RCA ((4) OUTPUT L and R)  
¼” TRS ((5) OUTPUT)  
Do not simultaneously use both PP400 OUTPUTs.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Actron Automobile Parts 2509 User Manual
Alliance Laundry Systems Washer LTS95AN User Manual
Alliance Laundry Systems Washer SF18VNV User Manual
Altinex Stereo Amplifier DA1907LX User Manual
American Standard Plumbing Product 621001 User Manual
AOC TV Video Accessories I2778VHE6 User Manual
Apple Network Card Video Card User Manual
Axor Plumbing Product 06064XX0 User Manual
Bahco Power Screwdriver BE 6990 IP User Manual
Eureka Tents Tent Copper Canyon 1610 User Manual