MatrixPRO-II
DVI 16x16 Matrix Router
User’s Guide
_________________________________________________________
Manual #: 26-1302001-00
Revision: 01Download from Www.Somanuals.com. All Manuals Search And Download.
MatrixPRO-II DVI 16x16 Router
________________________________________________________________________
Trademarks
Brand and product names mentioned in this manual may be trademarks, registered trademarks or
copyrights of their respective holders. All brand and product names mentioned in this manual serve
as comments or examples and are not to be understood as advertising for the products or their
manufactures.
__________________________________________________________________
Company Address
Barco, Inc.
11101 Trade Center Drive
Rancho Cordova,
California 95670 USA
Phone: (916) 859-2500
Fax: (916) 859-2515
Barco N.V.
Noordlaan 5 8520
Kuurne
BELGIUM
Phone: +32 56.36.82.11
Fax: +32 56.35.16.51
Website: www.barco.com
Technical Support
(866) 374-7878 — Events (24/7)
(866) 469-8036 — Digital Cinema (24/7)
3
User’s Guide
Rev. 01
Download from Www.Somanuals.com. All Manuals Search And Download.
MatrixPRO-II DVI 16x16 Router
________________________________________________________________________
Operators Safety Summary
The general safety information in this summary is for operating personnel.
Do not remove panels or covers
There are no user-serviceable parts within the unit. Removal of the top cover will expose dangerous
voltages. To avoid personal injury, do not remove the top cover. Do not operate the unit without the
cover installed.
Power Source
This product is intended to operate from a power source that will not apply more than 230 volts rms
between the supply conductors or between both supply conductor and ground. A protective ground
connection by way of grounding conductor in the power cord is essential for safe operation.
Grounding the Product
This product is grounded through the grounding conductor of the power cord. To avoid electrical
shock, plug the power cord into a properly wired receptacle before connecting to the product input or
output terminals. A protective-ground connection by way of the grounding conductor in the power
cord is essential for safe operation.
Use of the Power Cord
Use only the power cord and connector specified for your product. Use only a power cord that is in
good condition. Refer cord and connector changes to qualified service personnel.
Use of the Proper Fuse
To avoid fire hazard, use only the fuse having identical type, voltage rating, and current rating
characteristics. Refer fuse replacement to qualified service personnel.
Do not Operate in Explosive Atmospheres
To avoid explosion, do not operate this product in an explosive atmosphere.
4
User’s Guide
Rev. 01
Download from Www.Somanuals.com. All Manuals Search And Download.
MatrixPRO-II DVI 16x16 Router
________________________________________________________________________
Terms in This Manual and Equipment
Marking
Warning
Highlights an operating procedure, practice, condition, statement, etc.,
which, if not strictly observed, could result in injury to or death of
personnel.
Caution
The exclamation point within an equilateral triangle is intended to alert the user to
the presence of important operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
AVETISSEMENT!
Le point d´exclamation dans un triangle equilatéral signale à alerter l´utilisateur
qu´il y a des instructions d´operation et d´entretien tres importantes dans la
litérature qui accompagne l´appareil.
VORSICHT
Ein Ausrufungszeichen innerhalb eines gleichwinkeligen Dreiecks dient dazu, den
Benutzer auf wichtige Bedienungs-und Wartungsanweisungen in der Dem Great
beiliegenden Literatur aufmerksam zu machen.
Disposal of the Product (wast Electrical and
Electronic Equipment)
This symbol on the product indicates that, under the European Directive
2002/96/EC governing waste from electrical and electronic equipment, this
product must not be disposed of with other municipal waste. Please dispose of
your waste equipment by handing it over to a designated collection point for
the recycling of waste electrical and electronic equipment. To prevent possible
harm to the environment or human health from uncontrolled waste disposal,
please separate these items from other types of waste and recycle them
responsibly to promote the sustainable reuse of material resources.
For more information about recycling of this product, please contact your local
city office or your municipal waste disposal service. For details, please visit the
Barco website at:
Turkey RoHS Compliance
Türkiye Cumhuriyeti: EEE Yönetmeliğine Uygundur
Republic of Turkey: In conformity with the EEE Regulation
5
User’s Guide
Rev. 01
Download from Www.Somanuals.com. All Manuals Search And Download.
MatrixPRO-II DVI 16x16 Router
________________________________________________________________________
中国大陆 RoHS
Chinese Mainland RoHS
根据中国大陆《电子信息产品污染控制管理办法》（也称为中国大陆RoHS）， 以下部分列出了Barco产品
中可能包含的有毒和/或有害物质的名称和含量。中国大陆RoHS指令包含在中国信息产业部MCV标准：“电
子信息产品中有毒物质的限量要求”中。
According to the “China Administration on Control of Pollution Caused by Electronic
Information Products” (Also called RoHS of Chinese Mainland), the table below lists the
names and contents of toxic and/or hazardous substances that Barco’s product may contain.
The RoHS of Chinese Mainland is included in the MCV standard of the Ministry of
Information Industry of China, in the section “Limit Requirements of toxic substances in
Electronic Information Products”.
有毒有害物质或元素
零件项目(Ő称)
Hazardous Substances or Elements
Component Name
铅
汞
六价铬 多溴联苯
多溴二苯醚
镉
(Pb)
(Hg)
(PBB)
(PBDE)
(Cd)
(
Cr6+)
印制电路配件
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
Printed Circuit Assemblies
插入式印制电路配件
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
Plug in Printed Circuit Assembly
线
外接电( )缆
External Cables
底架
Chassis
电源供应器
Power Supply Unit
內部线路
Internal wiring
显示 (
)
Display
散热片(
)
Heatsinks
风扇
Fan
光盘说明书
CD Manual
正面(॔)面板
Front panel
O: 表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 标准规定的限量要求以下.
O:
Indicates that this toxic or hazardous substance contained in all of the homogeneous
materials for this part is below the limit requirement in SJ/T11363-2006.
X:
X:
表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 标准规定的限量要
求.
Indicates that this toxic or hazardous substance contained in at least one of the
6
User’s Guide
Rev. 01
Download from Www.Somanuals.com. All Manuals Search And Download.
MatrixPRO-II DVI 16x16 Router
________________________________________________________________________
homogeneous materials used for this part is above the limit requirement in SJ/T11363-2006.
在中国大陆销售的相应电子信息产品（EIP）都必须遵照中国大陆《电子信息产品污染控制标识要求》标准
贴上环保使用期限（EFUP）标签。Barco产品所采用的EFUP标签（请参阅实例，徽标内部的编号使用于制
定产品）基于中国大陆的《电子信息产品环保使用期限通则》标准。
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply
with the “Electronic Information Products Pollution Control Labeling Standard” of Chinese
Mainland, marked with the Environmental Friendly Use Period (EFUP) logo. The number
inside the EFUP logo that Barco uses (please refer to the photo) is based on the “Standard
of Electronic Information Products Environmental Friendly Use Period” of Chinese Mainland.
7
User’s Guide
Rev. 01
Download from Www.Somanuals.com. All Manuals Search And Download.
MatrixPRO-II DVI 16x16 Router
________________________________________________________________________
CHANGE HISTORY
Rev
00
Date
6/7/13
ECP #
606947
Description
User’s Guide
Approved By
GKOU
01
7/29/13
608395
User’s Guide
MYRA
8
User’s Guide
Rev. 01
Download from Www.Somanuals.com. All Manuals Search And Download.
MatrixPRO-II DVI 16x16 Router
________________________________________________________________________
TABLE OF CONTENTS
1 Introduction.....................................................................................................11
1.1 Key Features....................................................................................................11
1.2 Shipping..........................................................................................................11
1.3 Notice Of Safe Usage ........................................................................................12
1.4 Physical Description ..........................................................................................13
2 Installation ......................................................................................................14
2.1 Initialization.....................................................................................................14
2.2 EDID Configuration...........................................................................................14
3 Control Setup ...................................................................................................16
3.1 TCP/IP.............................................................................................................16
3.1.1 Launching Telnet............................................................................................16
3.2 RS-232............................................................................................................17
3.2.1 Launching HyperTerminal................................................................................17
4 Front Panel Operation ......................................................................................18
4.1 LINK mode.......................................................................................................18
4.2 UNLINK mode ..................................................................................................18
4.3 PRESET mode (“SHIFT ON PRESET”) ...................................................................18
4.4 FUNCTION mode ..............................................................................................18
4.4.1 Gateway .......................................................................................................19
4.4.2 Subnet Mask..................................................................................................19
4.4.3 IP Address.....................................................................................................19
4.4.4 MAC Address .................................................................................................20
4.4.5 UDP Port Number...........................................................................................20
4.4.6 Video Generator.............................................................................................20
4.4.7 Monitoring Output ..........................................................................................20
4.4.8 EDID Configure..............................................................................................20
4.4.9 HDCP Configure .............................................................................................22
4.4.10 Baud Rate .....................................................................................................23
4.4.11 Control Lock ..................................................................................................23
4.4.12 Reset Mode ...................................................................................................23
5 PC Program Operation......................................................................................24
5.1 Basic Setup......................................................................................................24
5.1.1 Connect Info..................................................................................................25
5.1.2 Channel Name ...............................................................................................26
5.1.3 Video Generator.............................................................................................26
5.1.4 Control Lock Mode..........................................................................................26
5.1.5 Network........................................................................................................26
5.2 EDID setup ......................................................................................................26
5.3 Operation ........................................................................................................27
5.3.1Input / output connection ..................................................................................28
5.3.2Input channel status .........................................................................................28
5.3.3Output channel status .......................................................................................29
6 Web control panel operation ............................................................................30
7 Commands .......................................................................................................31
7.1 Command input structure ..................................................................................31
7.2 Examples of command inputs.............................................................................32
7.2.1 Link input and output .....................................................................................32
9
User’s Guide
Rev. 01
Download from Www.Somanuals.com. All Manuals Search And Download.
MatrixPRO-II DVI 16x16 Router
________________________________________________________________________
7.2.2 Input and output status ..................................................................................32
7.2.3 Network setting .............................................................................................33
7.2.4 Monitor output port setting..............................................................................33
7.2.5 EDID control command...................................................................................33
7.2.6 HDCP Setting.................................................................................................34
7.2.7 Baud rate setting for RS-232 ...........................................................................34
7.2.8 Control lock command ....................................................................................35
8 Firmware update..............................................................................................36
9 HDCP notes ......................................................................................................40
10 Specifications...................................................................................................41
11 Warranty..........................................................................................................42
12 Contact Information.........................................................................................43
10
User’s Guide
Rev. 01
Download from Www.Somanuals.com. All Manuals Search And Download.
MatrixPRO-II DVI 16x16 Router
________________________________________________________________________
1
Introduction
The MATRIXPRO-II DVI 16x16 router enables users to switch up to 16 different DVI sources
to 16 different digital displays. Any input source, whether it‘s a HD-DVD player, Blue-Ray
player or a computer with high-resolution graphics, can be routed to a DVI or HDMI (via an
adaptor) output digital display.
The unit is fully compliant with the HDCP digital copy protection interface.
1.1 Key Features
▪ 16 DVI inputs and outputs
▪ DDC/HDCP compliant
▪ Supports up to WUXGA (1920x1200) at 60Hz refresh rate
▪ Supports 3 types of EDID management:
ñ
ñ
ñ
Default Mode
Auto Mix Mode
Output Copy Mode
▪ Supports various control methods:
ñ
ñ
ñ
ñ
Front panel button operation
Command input (Through RS-232 and Telnet connections)
Built in web panel control (TCP/IP)
PC program by RS-232 and UDP
▪ Supports entire family of Barco Encore Controllers
▪ Dual hot-swappable power supplies for power redundancy and load sharing
(Redundant supply is optional, Barco part number R767420K)
▪ Diagnostic function for quick troubleshooting
▪ Video generator output and input monitoring port for easy installation
1.2 Shipping
o MATRIXPRO-II DVI 16X16, Router (p/n R9004691): 1 EA
o AC power cord US: 1 EA
o AC power cord EU: 1 EA
o Quick Start Guide (QSG) : 1 EA
o Customer Registration Card: 1 EA
o Firmware download cable (RJ11 to DB9): 1 EA
o RS-232 cable (Straight type): 1 EA
o CD containing:
°
°
°
°
°
°
User’s Guide
Quick Start Guide
PC (GUI) Software
Router Firmware
Megaboot.exe
EDID Editor
11
User’s Guide
Rev. 01
Download from Www.Somanuals.com. All Manuals Search And Download.
MatrixPRO-II DVI 16x16 Router
________________________________________________________________________
1.3 Notice Of Safe Usage
We recommend you to read following warnings, precautions and information before
operating the unit.
▪ Use of the equipment in a manner not specified by the manufacturer may result in
irrecoverable damage
▪ Keep the unit away from liquid, magnetic and combustible substances
▪ Do not place heavy weight on the unit
▪ Do not install the unit in a hazardous location (i.e., high vibration or impact risk)
▪ Do not install the unit vertically
▪ Do not disassemble the unit
•
•
To turn the unit off completely, unplug the AC power cords
The switch on the front panel is only a reset switch
12
User’s Guide
Rev. 01
Download from Www.Somanuals.com. All Manuals Search And Download.
MatrixPRO-II DVI 16x16 Router
________________________________________________________________________
1.4 Physical Description
The MATRIXPRO-II DVI 16 X 16 router chassis is mountable on a 19” standard rack.
Key buttons, LCD display and reset switch are on the front panel as shown below.
Figure 1-1: Front panel of MATRIXPRO-II DVI 16 X 16
All Input and output cards, interface ports and power supplies are placed on the rear
panel as shown below.
▪ Input bay for 4 input cards (left side)
▪ Output bay for 4 output cards (right side)
▪ SERVICE, RJ-11 receptacle for firmware upgrades
▪ RS-232, Serial communication port
▪ LAN, RJ-45 receptacle for TCP/IP or UDP control
▪ REFERENCE OUTPUT provides an internal test pattern video source
▪ MONITORING OUTPUT provides an additional output to monitor input signals
▪ Power supplies (second power supply is optional, Barco p/n R767420K)
Figure 1-2: Rear panel of MATRIXPRO-II DVI 16 X 16
13
User’s Guide
Rev. 01
Download from Www.Somanuals.com. All Manuals Search And Download.
MatrixPRO-II DVI 16x16 Router
________________________________________________________________________
2
Installation
2.1 Initialization
▪ Connect the provided AC power cord to AC power inlet and turn on the front panel
switch
▪ The unit starts the initialization process. The message “Starting” will be shown on
the LCD display.
▪ After 17~20 sec, ‘MATRIXPRO-II DVI 16x16 Booting complete’ message will be
shown, along with hardware and firmware version information.
▪ The unit is now ready to receive commands from the user.
Typically, the IP address of PC connected to the network is configured by a
DHCP server. If the PC is connected directly to the router, the network server
will not able to assign the IP address. In this case, network information for
the PC should be set manually.
The default IP address of MATRIXPRO-II DVI 16x16 is 192.168.0.246. Before
connecting MATRIXPRO-II DVI 16x16 to your network, please verify the
availability of IP address in your network. The IP address can be reconfigured
by front panel key button, PC program or command lines over RS-232 or
TCP/IP.
2.2
EDID Configuration
▪ EDID (Extended Display Identification Data) is an information set that is provided
by a display to describe its capabilities to a graphic source. It enables a graphic
source to identify the connected display.
▪ The information set includes: manufacturer, product type, phosphor or filter type,
timings supported by the display, display size, luminance data and (for digital
displays only) pixel mapping data.
▪ Once the graphic source reads the information set (usually during the booting
process), the EDID conveys the optimal format for a connected display.
▪ The MATRIXPRO-II DVI supports storing EDID information to an EEPROM for each
Input.
▪ The MATRIXPRO-II DVI has three methods to set EDID values
1) Default Mode: default EDID information from the factory is loaded to an input
port
2) Output Copy Mode: read EDID from any target display and copy to an input
port
14
User’s Guide
Rev. 01
Download from Www.Somanuals.com. All Manuals Search And Download.
MatrixPRO-II DVI 16x16 Router
________________________________________________________________________
3) Auto Mix Mode: (The most advanced method) read all EDID information from
the attached input devices. An information set optimized for all inputs is
created and used to avoid any compliance problems in the field.
Displays
OUTPUT
Sources
INPUT
WRITE EDID
EEPROM1
EDID
EEPROM2
EEPROM3
INTERFACE
CONTROL
Read/Write
.
.
.
.
.
.
.
EEPROM16
Figure 2-1: EDID operation
As depicted in the Figure, once the EDID is configured, each EDID is stored in
EEPROM in Input ports. As a result, the video sources can read the EDID information
from the EEPROM during booting process.
The router’s default EDID resolution is 1280x1024 @ 60 Hz
15
User’s Guide
Rev. 01
Download from Www.Somanuals.com. All Manuals Search And Download.
MatrixPRO-II DVI 16x16 Router
________________________________________________________________________
3
Control Setup
The MATRIXPRO-II DVI 16x16 router can be controlled in various ways such as command
input (RS-232, TCP/IP), Web GUI control panel (TCP/IP), Windows application (RS-232,
UDP) as well as key button on the front panel. To use a PC for control, the PC must be
configured properly.
3.1
TCP/IP
TCP/IP, the abbreviation of Transmission Control Protocol (TCP) and the Internet
Protocol (IP) is commonly used protocol to control remote computers.
To control MATRIXPRO-II DVI 16x16 over TCP/IP, set network properties of PC as
below (Explained here is based on Win 7 OS).
▪ Open Control Panel.
▪ Select Network Status in Network and Internet menu.
▪ Select Adapter setting.
▪ Select Local Area Connection and right click to open property.
▪ Select Internet Protocol Version 4 (TCP/IPv4)
▪ Enter IP, Subnet mask, Gateway and DNS server address, compatible with the
current network setting of MATRIXPRO-II DVI 16x16
▪ Click OK to terminate IP setup session.
The router’s default IP address is 192.168.0.246
Set the PC’s IP address in the same range as the routers address:
192.168.001.nnn; where ‘nnn’ is not conflicting with other devices on the network
3.1.1 Launching Telnet
Telnet is a terminal program embedded in Window OS system to access remote
computers using TCP/IP protocol. With the network setting of the PC as above,
launch Telnet as below.
▪ Make sure that the PC and the router are connected by Ethernet.
▪ Click Start menu and select Run.
▪ Type CMD to open command window.
▪ Type ‘telnet 192.168.0.246’ (Type current IP address of the router)
▪ Press ENTER then, “==Welcome to MATRIXPRO-II DVI 16x16 ==” and “==
TELNET control ==” messages will be shown.
▪ Type the command to control the router
16
User’s Guide
Rev. 01
Download from Www.Somanuals.com. All Manuals Search And Download.
MatrixPRO-II DVI 16x16 Router
________________________________________________________________________
3.2
RS-232
3.2.1 Launching HyperTerminal
The MATRIXPRO-II router provides RS-232 serial communication. The simplest way
to control the router over RS-232 is using embedded Windows XP HyperTerminal
program.
Hyper Terminal is only supported by Windows XP. To install and
use Windows XP Mode in Windows 7 please refer to the Microsoft Windows web site
Alternatively, you can download and use the open source Putty terminal software.
To launch Hyper Terminal
▪ Connect the PC to the unit with a RS-232 cable.
▪ Select Start > Programs > Accessories > Communications > HyperTerminal.
▪ Enter a name and choose an icon in Connection Description window and click OK.
▪ In Connect To window, ignore the Country, Area Code and Phone Number fields
but select available COM port of PC and then click OK.
▪ In COM Properties window, set the parameters as below:
ñ Bits per second (baud rate): 115200 (115200 is default baud rate of
MATRIXPRO-II DVI 16x16 )
ñ Data bits: 8
ñ Parity: None
ñ Stop bits: 1
ñ Flow control: None
Bit per second of Hyper Terminal should be set as same as baud rate of MATRIXPRO-II
▪ Click OK to save the parameters.
▪
Go Start > Programs > Accessories > Communications > HyperTerminal,
then new icon will be shown. Then select it to launch Hyper Terminal
▪
Type the command to control the unit
17
User’s Guide
Rev. 01
Download from Www.Somanuals.com. All Manuals Search And Download.
MatrixPRO-II DVI 16x16 Router
________________________________________________________________________
4
Front Panel Operation
4.1 LINK mode
▪ It configures input / output connections for cross-switching.
1) Press LINK key button.
2) Press an input key button - LCD will display current connected output.
3) Press single or multiple output key buttons to select desired outputs.
4) Outputs can be deselected by pressing the output key button again.
5) Press ENTER key button to save the configuration.
6) To configure next Input / output connection, repeat steps 1 to 5.
4.2 UNLINK mode
▪ It unlinks input /output connection.
1) Press LINK key button.
2) Press SHIFT key button. “UnLINK” should now be displayed.
3) Press the input key button for the routing you would like to clear.
4) Press ENTER key button.
4.3 PRESET mode (“SHIFT ON PRESET”)
▪
The Preset function is currently unavailable. This feature will be added in the future.
4.4 FUNCTION mode
▪ This function enables the configuration of the unit allowing it to be controlled by
commands input or from the PC windows program
▪ By pressing the FUNCTION button, the menu on the front panel display will cycle
through the following features:
1. Gateway
2. Subnet Mask
3. IP Address
4. Mac Address
5. UDP Port Number
6. Video Generator
7. Monitoring Output
8. EDID Configure
9. HDCP Configure
10. Baud Rate
11. Control Lock
12. Reset Mode
18
User’s Guide
Rev. 01
Download from Www.Somanuals.com. All Manuals Search And Download.
MatrixPRO-II DVI 16x16 Router
________________________________________________________________________
4.4.1 Gateway
▪ The cursor shows that it is selected and activated.
▪ Input 3 key button decreases the number.
▪ Input 4 key button increases the number.
▪ Input 1 and 2 key buttons move the cursor left and right.
======Gate Way======
O: 192. 168. 000. 001
N: 192. 168. 000. 001
▪ Modify the Gate way address to be used for your network.
▪ Press ENTER key button to complete the process.
▪ The default setting is 192.168.000.001
4.4.2 Subnet Mask
▪ The cursor shows that it is selected and activated.
▪ Input 3 key button decreases the number.
▪ Input 4 key button increases the number.
▪ Input 1 and 2 key buttons move the cursor left and right.
====Subnet Mask====
O: 255. 255. 255. 000
N: 255. 255. 255. 000
▪ Modify the Subnet mask address to be used for your network.
▪ Press ENTER key button to complete the process.
▪ The default setting is 255.255.255.000.
4.4.3 IP Address
▪ The cursor shows that it is selected and activated.
▪ Input 3 key button decreases the number.
▪ Input 4 key button increases the number.
▪ Input 1 and 2 key buttons move the cursor left and right.
=====IP Address=====
O: 192. 168. 0. 246
N: 192. 168. 0. 246
▪ Modify the IP address to be used for your network.
19
User’s Guide
Rev. 01
Download from Www.Somanuals.com. All Manuals Search And Download.
MatrixPRO-II DVI 16x16 Router
________________________________________________________________________
▪ Press ENTER key button to complete the process.
▪ The default setting is 192.168.0.246
4.4.4 MAC Address
▪ MAC Address of the unit is displayed. This is a fixed value and cannot be changed.
4.4.5 UDP Port Number
▪ This will display the UDP port number.
▪ The default UDP port number is 03000. The UDP port number cannot be changed
using the front panel keys.
Port number setting in this section is used for UDP with supplied PC program not TCP/IP
with web browser or Telnet. For TCP/IP, port number 23 is fixed value.
.
4.4.6 Video Generator
▪ The Video Generator (Reference Output) is set at 1280x1024@60Hz with a Vertical
Bar pattern. This output cannot be changed.
4.4.7 Monitoring Output
▪ It allocates input to Monitor Output port for monitoring uses.
▪ The cursor shows that it is selected and activated.
▪ Input 3 key button decreases the number.
▪ Input 4 key button increases the number.
=Monitoring Output=
Old Input: 01
New Input: 01
1) Connect a display to the Monitoring Output port and any video sources to the
DVI input ports on the real panel.
2) Select an input port by pressing input 3 or 4 key button.
3) Press ENTER key button to complete the process.
4.4.8 EDID Configure
▪ Sets the EDID information in input port.
▪ MATRIXPRO-II DVI 16x16 supports three types of EDID setting: Default Mode, Auto
Mix Mode and Output Copy Mode. For more information, refer to Chap. 5.2.
▪ The cursor shows that it is selected and activated.
▪ Input 1 and 2 key buttons select YES and NO.
▪ Input 3 and 4 key buttons move left and right (Change EDID mode).
▪ Input 5 and 6 key buttons move down and up (Decrease and increase the port
number).
20
User’s Guide
Rev. 01
Download from Www.Somanuals.com. All Manuals Search And Download.
MatrixPRO-II DVI 16x16 Router
________________________________________________________________________
===EDID Configure===
Entry EDID
Configure? _1: Entry
1) Press input 1 key button to enter the EDID Configure Mode.
===EDID Configure===
Input: 01 Default
Default Mode?
1: Y 2: N 3: << 4: >> 5: ∨ 6: ∧
The EDID configuration that is shown next to the input number on the LCD
display is the current EDID mode
2) Select an input port by pressing input 5 or 6 key button.
3) Press input 3 or 4 key button to change EDID mode.
3-1) If you select Default Mode, default EDID will be restored for allocated
inputs.
===EDID Configure===
Input: 01 Default
Default Mode?
1: Y 2: N 3: << 4: >> 5: ∨ 6: ∧
Press input 1 key button then, the MATRIXPRO-II DVI 16x16 will recover
the Default EDID to allocated input as below.
===EDID Configure===
EDID Copying….
EDID Reading….
3-2) If you select Auto Mix Mode, mixed EDID of all attached displays will be
saved in allocated input.
3-3) If you select Output Copy Mode, MATRIXPRO-II DVI 16x16 reads EDID
from any target displays and copies it in allocated input.
New EDID can be created or existing EDID can be modified using the Edit Data Mode. This
feature is recommended for advanced users only.
▪
Improper EDID setting can compromise the stability of the system
Not all computer graphics cards will be able to output a custom EDID resolution.
▪
▪
Be sure that you fully understand this feature prior to use.
For further information, please contact [email protected]
Download from Www.Somanuals.com. All Manuals Search And Download.
MatrixPRO-II DVI 16x16 Router
________________________________________________________________________
4.4.9 HDCP Configure
Disabling HDCP Compatibility
By default, the MATRIXPRO-II DVI 16X16 is an HDCP compatible Video Router. HDCP
protected content received on a DVI input connector from an input source such as a Blu-ray
player is processed and output on the DVI output connector(s) to an HDCP compliant
display device.
Occasionally, an input source which is supplying video which is not meant to be protected
may add HDCP protection to the content solely because it has detected that the
MATRIXPRO-II DVI 16x16 is capable of processing HDCP protected content. In this case, if
HDCP compatible display devices are not used, this content can not be processed and
output by the MATRIXPRO-II DVI Router, and the content can not be displayed. This has
occurred at times when outputting content from an Apple MacBook Pro via a
mini-DisplayPort to a DVI-adapter.
In order to allow the use of sources such as the MacBook Pro to display non-HDCP protected
data (for example, the show graphics) with standard non-HDCP compliant displays, we have
added the ability to disable HDCP compatibility in the MATRIXPRO-II DVI 16x16
Router. Please note that this new feature DOES NOT allow output of HDCP protected
content to non-HDCP compliant devices. It simply allows the user to force the MATRIXPRO-
II DVI to behave as a non-HDCP compatible device.
HDCP CONFIGURE
▪Allows you to turn the HDCP On or Off for any of the Inputs
▪Input 1 and 2 key buttons select the Input number
▪Input 3 and 4 key select HDCP On or Off
===HDCP Configure===
Input: 01
HDCP Compatible ON
1: ∨ 2: ∧ 3:ON 4:OFF
Select the Input using the Input 1 and 2 keys
To turn “ON” HDCP press the Input 3 key and to turn “OFF” HDCP press the 4 key
Press ENTER key to complete the process
Note: The MATRIXPRO-II DVI 16x16 Router will return to HDCP ON for all inputs after a “Factory Reset”
22
User’s Guide
Rev. 01
Download from Www.Somanuals.com. All Manuals Search And Download.
MatrixPRO-II DVI 16x16 Router
________________________________________________________________________
4.4.10 Baud Rate
▪ Sets the RS-232 Baud Rate. MATRIXPRO-II DVI 16x16 supports 9600, 19200,
38400, 57600, 115200bps.
=====Baud rate=====
Old baud: 115200
New baud: 115200
▪ Input 3 key button decreases the number.
▪ Input 4 key button increases the number.
▪ Press ENTER key button to complete the process.
▪ The default setting is 115200
4.4.11 Control Lock
▪ Locks and unlocks the controls such as Web, RS-232, TCP/IP, UDP and key button
====Control Lock====
Web Lock?
Data Lock?
Key Lock?
UnLock
UnLock
UnLock
▪ Input 1 and 2 key buttons move the cursor up and down.
▪ Input 3 key button moves Lock.
▪ Input 4 key button moves UnLock.
▪ Press ENTER key button to complete the process.
4.4.12 Reset Mode
▪ Resets the unit. After reboot it will restore all default settings.
▪ Input 1 and 2 key buttons select YES and NO.
▪ Press ENTER key button to complete the process.
23
User’s Guide
Rev. 01
Download from Www.Somanuals.com. All Manuals Search And Download.
MatrixPRO-II DVI 16x16 Router
________________________________________________________________________
5
PC Program Operation
Run the setup.exe to install MATRIXPRO-II DVI 16x16 PC program. The Barco icon will be
shown on the wallpaper. Double click it to launch PC program for MATRIXPRO-II DVI 16x16.
The PC program provides a user-friendly graphic interface alternative to key button input
and command input operation.
Copy MPII-DVIsetup.exe file in any directories in your PC and double click it to run. The
initial window of PC program for MATRIXPRO-II DVI 16x16 as shown below will appear.
5.1 Basic Setup
Click Set Config button to set the communication method, input / output name, Video
generator and so on. Then, the Set Config window as below will open.
24
User’s Guide
Rev. 01
Download from Www.Somanuals.com. All Manuals Search And Download.
MatrixPRO-II DVI 16x16 Router
________________________________________________________________________
5.1.1 Connect Info
▪
Select the connection method to be either RS-232 and Ethernet (UDP) by
clicking the corresponding radio buttons
▪
For RS-232 control, enter the COM port number of your PC and select baud
rate. The baud rate of your PC should be the same as the MATRIXPRO-II DVI
16x16 baud rate. (115200 is default)
▪
▪
▪
For Ethernet control, enter the IP address of the MATRIXPRO-II DVI 16x16 and
port number. 3000 is the default port number for the MATRIXPRO-II DVI 16x16.
Click save button and close Set Config window then click Connect button on PC
program of MATRIXPRO-II DVI 16x16 to start it.
If the connection is properly made, current status of MATRIXPRO-II DVI 16x16
will be shown at the bottom side of PC program.
25
User’s Guide
Rev. 01
Download from Www.Somanuals.com. All Manuals Search And Download.
MatrixPRO-II DVI 16x16 Router
________________________________________________________________________
5.1.2 Channel Name
▪
User can create specific names for all inputs and outputs to distinguish them
▪
On Fig 4.2, The name of Camera #1 was assigned to Input CH05 and Wall
display #3 for output CH07.
▪
Click Save button to save it then, these will be applied on the PC program as
shown in Fig 4-1.
5.1.3 Video Generator
▪
Select the resolution and pattern of video generator.
▪
Click Apply button to save it.
5.1.4 Control Lock Mode
▪
Locks and unlocks the controls such as Web, Data control (RS-232, TCP/IP and
UDP) and key button input.
▪
Click Apply button to save it.
5.1.5 Network
▪
Changes the network information of MATRIXPRO-II DVI 16x16 .
▪
Click Apply button to save it.
5.2 EDID setup
MATRIXPRO-II DVI 16x16 offers 3 types of EDID settings for easy installation with
various displays in the market. To set the EDID option for each input port, click Set
EDID button. The Setup EDID window will open.
To set EDID information for each input, select the appropriate MODE button and click
the input channel. For each mode, multi-input channels can be selected the same time.
26
User’s Guide
Rev. 01
Download from Www.Somanuals.com. All Manuals Search And Download.
MatrixPRO-II DVI 16x16 Router
________________________________________________________________________
▪
▪
▪
Default mode is the default EDID as set the factory. Selecting this mode will
restore the default EDID on the selected input channels.
Auto Mix mode is an advanced EDID mode. In the mode the unit reads all EDID
of attached displays and creates and custom input EDID.
Output Copy mode reads the EDID from any selected output channel and
copies it into an input port. Select the output channel first and then click the
input channels. Click the Apply button to save settings.
▪
Edit Data Mode is used to modify existing EDIDs or to make a new custom
EDID. This feature is recommended for advanced users only.
Improper EDID setting can compromise the stability of the system. Not all computer
graphics cards will be able to output a custom EDID resolution. Be sure you fully
understand this feature prior to use.
For further information, please contact [email protected]
5.3 Operation
The communication settings and system status are on the right side of the control
application as shown below. After clicking the Connect button (Refer to Chap. 4.1.1),
the MatrixPRO-II DVI is ready to receive commands from user.
27
User’s Guide
Rev. 01
Download from Www.Somanuals.com. All Manuals Search And Download.
MatrixPRO-II DVI 16x16 Router
________________________________________________________________________
The left side of the control application shows the signal connection, resolution, EDID,
and routing status of the inputs and outputs.
5.3.1 Input / output connection
▪
Click on one of the input channels and click on any of the output channels. If
you click on input CH05 (Camera #1) and click on outputs CH05, CH06, CH07
and CH08, the input signal from CH05 will be connected to outputs 05, 06, 07
and 08 as shown in Fig 4-5.
▪
▪
To connect one input to all outputs, click All Link button and click desired input.
Then all of the outputs will be connected to the selected input.
To disconnect all outputs, click the Link Clear button.
5.3.2 Input channel status
▪
Green LEDs above the input channel numbers indicate that a signal has been
detected. In fig 4-5 above, CH05 and CH10 have detected signals.
▪
When a signal has been detected, the resolution will also be displayed beneath
the channel name (ex. CH05=1920x1080p).
▪
▪
If no signal is detected the input will display ‘Signal OFF’.
DEF., AUTO, OUT. and USER, indicate the current EDID mode assigned to that
input channel (Refer to Chap. 4.2)
28
User’s Guide
Rev. 01
Download from Www.Somanuals.com. All Manuals Search And Download.
MatrixPRO-II DVI 16x16 Router
________________________________________________________________________
5.3.3 Output channel status
▪
Green LEDs above the output channel number indicate Hot Plug Detection (HPD)
from display. For example CH07 is connected to a display.
The connected outputs show input source information (ex. CH07=Camera #1,
input CH05).
▪
▪
The disconnected outputs show ‘No Link’.
29
User’s Guide
Rev. 01
Download from Www.Somanuals.com. All Manuals Search And Download.
MatrixPRO-II DVI 16x16 Router
________________________________________________________________________
6
Web control panel operation
The Web control panel operation provides a user-friendly graphic interface and easy access
to control the MATRIXPRO-II DVI 16x16. Some functions available from the PC GUI and
front panel are not available from the Web control panel.
•
•
Microsoft Explorer is the recommended browser to run the Web control panel.
Before running the web, confirm the Network setting of MATRIXPRO-II DVI
16x16 and Ethernet connection of the PC (Refer to Chap 2 and Chap 3).
Launch the web browser and enter the IP address of current MATRIXPRO-II DVI 16x16 into
the URL address line. For example, 192.168.0.246
Fig 6-1 shows structure of Web control panel. It controls input / output connection, video
generator and informs simple input / output status. Reminder, after new input /output
connection, user has to click LINK button and SEND button for new generator setting.
30
User’s Guide
Rev. 01
Download from Www.Somanuals.com. All Manuals Search And Download.
MatrixPRO-II DVI 16x16 Router
________________________________________________________________________
7
Commands
The MATRIXPRO-II DVI 16x16 router can be operated with various interfaces such as key
button inputs, command input through RS-232 and TCP/IP, Web control through TCP/IP and
PC program through RS-232 and UDP. All functions are executed on a basis of a serial
command input, but the graphic interfaces on the Web or the PC program are more efficient
ways to operate the MATRIXPRO-II DVI 16x16 modular matrix.
Command input operation is accomplished through RS-232 or TCP/IP. For setting
procedures using those protocols, please refer to Chap 2 and Chap 3.
7.1 Command input structure
The command inputs are composed of a string of ASCII codes and its basic structure is;
Command + Delimiter (‘=’) + Data + Delimiter (‘^’ or ‘,’ or ‘_’) + Data + End (‘!’)
Table 6.1 shows all commands and its brief descriptions
Command
LINK
Description
Input and Output connection
Input signal status request
Output signal status request
Network information request
Gateway address setting
Subnet mask address setting
IP address setting
IN
OUT
NET
NETGW
NETSN
NETIP
NETPA
NETPT
VID
MAC address setting
UDP port number setting
Video generator status request
Monitoring port setting and status request
EDID mode setting
MON
EDID
HDCP
RS232
LOCK
Enable/Disable HDCP
RS-232 Baud rate setting
Lock/Unlock the control type
Table 7-1 : Commands set
▪ The command input allows executing only one command. Multiple command inputs
require executing multiple strings having each command per a string.
▪ User can use capital letters and small letters for commands but cannot mix it like
‘Link’, it must be corrected as ‘link’ or ‘LINK’.
31
User’s Guide
Rev. 01
Download from Www.Somanuals.com. All Manuals Search And Download.
MatrixPRO-II DVI 16x16 Router
________________________________________________________________________
▪ After all input commands, MATRIXPRO-II DVI 16x16 sends back replies to conform
the execution of commands.
▪ Input and output port number range from 1 to 16 and prefix, ‘0’ can be used such
as ‘001’ and ‘010, but in the replies after the command inputs, the digits of port
number are two such as ‘01’ and ‘10’.
7.2 Examples of command inputs
7.2.1 Link input and output
▪ Makes single or multi-connections of inputs and outputs.
▪ Makes disconnection of all inputs when used with ‘0’.
▪ Requests inputs and outputs status of MATRIXPRO-II DVI 16x16.
Command
Description and reply
Makes input 1 connected to output 10.
Reply: LINK=01^10!
LINK=01^10!
Makes input 1 connected to output 3 and 4 to 7.
Reply: LINK =01^03,04^07!
LINK
=1^03,04^7!
Makes input 5 connected to all outputs.
Reply: LINK=05!
LINK =05!
LINK =00!
Makes all connections disconnected.
Reply: LINK =00!
Makes output 6 disconnected.
Reply: LINK =00^06!
LINK =00^06!
Requests current inputs and outputs connections
status.
Link=?!
Reply: LINK =01^01,02^04,~16^13!
Table 7-2: Link command examples
7.2.2 Input and output status
▪ Requests input signal status. If the input is connected, it replies input resolution,
but if it is not connected, it returns ‘Signal Off’.
▪ Requests output status whether it is connected to display or not.
Command
IN=05!
Description and reply
Requests input 5 status.
Reply: IN=[05] 1920x1200p! or IN=[05] Signal Off!
Requests output 12 status.
Reply: OUT=[12] Un Plugged! or OUT=[12] Plugged!
OUT=12!
Table 7-3: Input and output status command examples
32
User’s Guide
Rev. 01
Download from Www.Somanuals.com. All Manuals Search And Download.
MatrixPRO-II DVI 16x16 Router
________________________________________________________________________
7.2.3 Network setting
▪ Sets the IP, Gateway, Subnet mask, MAC address and UDP port number.
▪ Requests current network setting.
Command
Description and reply
Sets Gateway address, each data ranges from 000 to 255.
Reply: NETGW=192.168.001.001!
NETGW=192.168.1.1!
Sets IP address, each data ranges from 000 to 255.
Reply: NETGW=192.168.001.118!
Sets Subnet mask address, each data ranges from 000 to
255.
NETIP=192.168.1.118!
NETSN=255.255.255.0!
Reply: NETSN=255.255.255.000!
Sets MAC address, each data ranges from 00 to FF.
Reply: NETPA= AA.BB.CC.DD.EE.FF!
NETPA=AA.BB.CC.DD.EE.FF!
NETPT=3000!
Sets UDP port number, data ranges from 0 to 65535.
NETPT=3000!
Requests current network setting.
Reply: NETGW=192.168.001.001!
NETIP=192.168.001.118!
NETSN=255.255.255.000!
NETPA=AA.BB.CC.DD.EE.FF!
NETPT=3000!
NET=?!
Table 7-4 : Network setting command examples
7.2.4 Monitor output port setting
▪ Makes an input connected to the Monitor Output port.
▪ Requests input port that is currently connected to the Monitor Output port.
Command
MON=13!
Description and reply
Makes input 13 connected to monitor output ports.
Reply: MON=13!
Requests current input port that connected to monitor
MON=?!
output port.
Reply: MON=13!
Table 7-5: Monitor output setting command examples
7.2.5 EDID control command
▪ It stores EDID information in input port of MATRIXPRO-II DVI 16x16 .
▪ It requests current EDID setting for all input ports.
33
User’s Guide
Rev. 01
Download from Www.Somanuals.com. All Manuals Search And Download.
MatrixPRO-II DVI 16x16 Router
________________________________________________________________________
Command
Description and reply
Default mode: Saves default EDID in input ports 1, 7 and 15.
Reply: EDID=01DEF.!
EDID=07DEF.!
EDID=DE1,7,15!
EDID=15DEF.!
Auto mix mode: Analyzes all EDID information of connected
displays to makes optimized EDID then save it in input ports
2, 8 and 9.
EDID=AUTO2,8,9!
Reply: EDID=02AUTO!
EDID=08AUTO!
EDID=09AUTO!
Output copy mode: Copies EDID information of output 3
display and stores it in input port 5.
Reply: EDID=03OUT.!
EDID=OUT3_5!
EDID=?!
Requests current EDID setting for all inputs.
Reply: EDID=01OUT.02AUTO03OUT.~16EDF.!
Table 7-6: Monitor output setting command examples
7.2.6 HDCP Setting
▪ Allows the user to turn HDCP On or Off for any of the 16 input ports.
Command
Description and reply
Retrieves HDCP setting for all Inputs
HDCP=?!
Reply: HDCP=01OFF,02ON,03ON,04ON,05ON,06OFF,
07ON,08ON,09ON,10OFF,11ON,12OFF,13ON,14ON,15ON,16ON!
Sets HDCP for Input 9 to OFF
Reply: HDCP=[09]OFF!
HDCP=9OFF!
HDCP=12ON!
Sets HDCP for Input 12 to ON
Reply: HDCP=[12]ON!
7.2.7 Baud rate setting for RS-232
34
User’s Guide
Rev. 01
Download from Www.Somanuals.com. All Manuals Search And Download.
MatrixPRO-II DVI 16x16 Router
________________________________________________________________________
▪ Sets the RS-232 baud rate. MATRIXPRO-II DVI 16x16 supports 9600, 19200,
38400, 57600, 115200bps.
▪ Requests the current RS-232 baud rate.
Command
Description and reply
Sets RS-232 baud rate.
Reply: RS232=115200BPS!
RS232=115200!
Requests current baud rate.
Reply: RS232=115200BPS!
RS232=?!
Table 7-7: Baud rate setting command examples
7.2.8 Control lock command
▪ Locks and unlocks the controls such as Web, RS-232, TCP/IP and UDP.
▪ Requests open status of controls.
ASCII
WL
Description
Web control lock
WUL
DL
Web control unlock
Data control (UDP, TCP/IP, RS-232) lock
Data control (UDP, TCP/IP, RS-232) unlock
Key control lock
DUL
KL
KUL
Key control unlock
Table 7-9: Locking type and its ASCII data
Command
LOCK=DL!
Description and reply
Locks data control.
Reply: LOCK=DL!
Request current status of control method.
Reply: LOCK=WUL,DUL,KUL!
LOCK=?!
Table 7-10 : Control lock command examples
35
User’s Guide
Rev. 01
Download from Www.Somanuals.com. All Manuals Search And Download.
MatrixPRO-II DVI 16x16 Router
________________________________________________________________________
8
Firmware update
1. Using a Windows XP based PC, install the megaboot.exe program provided on a
CD.
You can run Megaboot.exe with Windows 7, as an Administrator.
Alternatively, you can run Megaboot.exe under Windows XP.
2. Click ①, Open of ‘File to be programmed in the Flash’ to select directory and
file (hex. Format) to be uploaded.
36
User’s Guide
Rev. 01
Download from Www.Somanuals.com. All Manuals Search And Download.
MatrixPRO-II DVI 16x16 Router
________________________________________________________________________
①
③
②
3. Connect the Service Port located on the rear panel of the MATRIXPRO-II DVI 16x
16 to a RS-232 (Comm port) on a PC using the supplied download cable (RJ1
1 to D-Sub 9Pin cable).
4. Select ②, ‘Comm port’ to select communication port of PC for RS-232
communication with MATRIXPRO-II DVI 16x16.
5. To enable Comm port, Click ③ when it shown as ‘Serial Port Enable’.
6. Power-On the MATRIXPRO-II DVI 16x16.
7. The firmware upload should then begin and the status will be shown in the message
box as shown below.
37
User’s Guide
Rev. 01
Download from Www.Somanuals.com. All Manuals Search And Download.
MatrixPRO-II DVI 16x16 Router
________________________________________________________________________
8. After 1 to 2 minutes, and “All Done” message will be shown. Then the firmware
upload is completed.
38
User’s Guide
Rev. 01
Download from Www.Somanuals.com. All Manuals Search And Download.
MatrixPRO-II DVI 16x16 Router
________________________________________________________________________
9. Close the MegaBoot.exe program and reboot MATRIXPRO-II DVI 16x16 to run it
under the new firmware.
39
User’s Guide
Rev. 01
Download from Www.Somanuals.com. All Manuals Search And Download.
MatrixPRO-II DVI 16x16 Router
________________________________________________________________________
9
HDCP notes
HDCP stands for High-Bandwidth Digital Content Protection, an industry-wide copy
protection scheme that is used to prevent the potential interception of digital data between
the source (e.g., a Blu-Ray player) and the target display (e.g., an HDCP compliant display
or monitor). The HDCP format was designed by Intel®, and it uses an “authentication and
key exchange” procedure to accomplish the required protection. For proper implementation,
products that are compatible with the HDCP format require a secure connection to a
compliant display, such as a projector or monitor.
In applications in which the DVI router is used, when an HDCP compliant device is
connected to the router, an HDCP “session” is created. In this session (which is transparent
to the user), “keys” are exchanged between the source device (e.g., a Blu-Ray player) and
the HDCP compliant display.
The source device queries the display to ensure that the equipment is HDCP compliant
before video is shown. Non-HDCP equipment such as PCs will work with any DVI compliant
display, but HDCP compliant equipment only shows “protected” content on HDCP compliant
displays.
40
User’s Guide
Rev. 01
Download from Www.Somanuals.com. All Manuals Search And Download.
MatrixPRO-II DVI 16x16 Router
________________________________________________________________________
10
Specifications
Video INPUTS
DVI
●All single-link DVI digital formats up to 165 Mhz, per DVI 1.0
specification
● EDID version 1 .3 compatible
Video OUTPUTS
DVI
Formats: all single-link DVI digital formats up to 165 Mhz, per DVI 1.0
specification
Reference and
Monitor
Formats: all single-link DVI digital formats up to 165 Mhz, per DVI 1.0
specification
Physical and Electrical Specifications
Control
Ethernet RJ-45, 10/100 Mbps autosense
Height
7 in, 178 mm (4RU
Width
17.32 in, 440 mm
Depth
14.96 in, 380 mm
Weight
< 10 kg
Input power
Environmental
Temperature
Warranty
100-240 VAC, 50-60 Hz, 800 watts max. (each supply)
Humidity: 0-95% non-condensing
0-40° C
Full three-year parts and labor warranty
41
User’s Guide
Rev. 01
Download from Www.Somanuals.com. All Manuals Search And Download.
MatrixPRO-II DVI 16x16 Router
________________________________________________________________________
11
Warranty
Warranty
All video products are designed and tested to the highest quality standards and are backed
by a full 3-year parts and labor warranty. Warranties are effective upon delivery date to
customer and are non-transferable. Barco warranties are only valid to the original
purchaser/owner. Warranty related repairs include parts and labor, but do not include faults
resulting from user negligence, special modifications, lightning strikes, abuse (drop/crush),
and/or other unusual damages.
The customer shall pay shipping charges when unit is returned for repair. Barco will cover
shipping charges for return shipments to customers.
Return Material Authorization (RMA)
In the unlikely event that a product is required to return for repair, please call the
Technical Support / Customer Service direct line, and ask to receive a Return
Merchandise Authorization number (RMA).
RMA Conditions are listed below:
a. Prior to returning any item, you must receive a Return Merchandise
Authorization (RMA) number.
b. All RMA numbers must appear on their return-shipping label.
c. RMA numbers are valid for ten (10) days from issue date.
d. All shipping and insurance charges on all RMAs must be prepaid by the customer
42
User’s Guide
Rev. 01
Download from Www.Somanuals.com. All Manuals Search And Download.
MatrixPRO-II DVI 16x16 Router
________________________________________________________________________
12
Contact Information
Barco Inc.
11101 Trade Center Drive
Rancho Cordova, California 95670
USA
• Telephone: (916) 859-2500
• Fax: (916) 859-2515
Sales Contact
• Direct: (916) 859-2505
• Toll Free: (888) 414-7226
• E-mail: [email protected]
Barco N.V.
Noordlaan 5
8520 Kuurne
BELGIUM
• Telephone: +32 56.36.82.11
• Fax: +32 56.35.16.51
Technical Support (USA)
• Telephone: (866) 374-7878 — 6 a.m. to 10 p.m. (PST), 7 days per week
• E-mail: [email protected]
Technical Support (Europe, Middle East, Asia)
Telephone: 0800900410
43
User’s Guide
Rev. 01
Download from Www.Somanuals.com. All Manuals Search And Download.
|