T-SERIES PORTABLE
BABY BASSINET ‘N CRADLE
WITH TOYBOX BASE
MODEL NUMBERS:
0850T White Batiste
00750 Pink Waffle
00751 Blue Waffle
00752 Sage Waffle
0860T Sage Waffle Pleated
0861T Ecru Waffle Pleated
0854T Moon/Star
0852T Sage Gingham
Assembly
Instructions.
Adult Assembly
Required.
Save these
instructions for
future use.
Visit us online at www.badgerbasket.com
Toll-Free Customer Service: 1-800-236-1310 (Monday through Thursday 7:30 AM to 4:30 PM CST)
Mail: PO Box 227, Edgar, WI 54426-0227 • Phone: 715-352-2311 • Fax: 715-352-3163
Page 1 of 6
3.0/1108/TG
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS & HARDWARE:
TOOLS NEEDED:
Phillips Screwdriver*
* Power screwdriver is helpful but be careful not to damage the product
PARTS INCLUDED (pictures not to scale):
(A) 2 - End Panels
(G) 1 - Set of Caster Wheels, includes:
(note inside and outside faces)
(B) 4 - Rails
(C) 8 - Bolts
(D) 2 - Nylon Snap Straps
(E) 2 - Dowels
4 Wheels, 4 Bolts, 4 Knobs
(H) 1 - Bassinet Body (not shown)
(I) 1 - Bedding Set (not shown), includes:
1 Liner/Skirt, 1 Sheet, 1 Hood Cover
(J) 1 - Mattress Pad (not shown)
(K) Hood Hoop Frame (2 pieces, not shown)
(L) 2 - Side Panels, 1 - Bottom Panel
(for Toy Box Base)
(F) 1 - Mesh Basket
C
D
E
G
A
F
L
B
A
USE AND CARE INSTRUCTIONS:
Wipe the wood/MDF parts clean with a damp cloth and mild soap as needed.
Spot clean basket as needed. Bedding Set can be machine washed on cold,
gentle cycle; tumble dry low or no heat.
Page 3 of 6
3.0/1108/TG
Download from Www.Somanuals.com. All Manuals Search And Download.
PICTURE 1
STEP 1: See PICTURE 1. Take ONE END PANEL (A)
and attach the FOUR RAILS (B) using FOUR BOLTS
(C).
D
A
Attach the rails to the INSIDE FACE of the END
PANEL. The inside face has countersunk areas for the
rails and slots that you will use later for the mesh basket.
Position the bottom rails with the grooves facing
up; and position the top rails with the grooves facing
down.
B
B
Slip the TWO NYLON SNAP STRAPS (D) over
the TOP RAILS (B). Position them so that they are ready
to snap to the snaps on the bassinet body (H).
B
STEP 2: See PICTURE 2. Attach the second END
PANEL(A) to the FOUR RAILS (B) using FOUR BOLTS
(C).
B
STEP 3: See PICTURES 3A and 3B. Turn the bassinet
stand upside down.
PICTURE 2
Insert the TWO DOWELS (E) through the edge
pockets of the MESH BASKET (F). Insert the ends of
the ONE DOWEL (E) into the SLOTS cut into the inside
faces of the END PANELS (A). Stretch the mesh basket
over the rails and around to the other side, and insert the
second wood dowel into the dowel slots.Adjust the mesh
basket to remove wrinkles.
Attach the FOUR CASTER WHEELS (G) to the
corners of the end panels using one BOLT and one KNOB
for each WHEEL. The knobs go on the inside.
A
STEP 4: See PICTURES 4A and 4B. Turn the bassinet
stand over.
Fit the slots on the BASSINET BODY (H) over the
raised edge pieces on the top of the END PANELS (A).
See PICTURE 4A.
Next, snap the NYLON SNAP STRAPS (D) onto
the snaps on the bottom edge of the BASSINET BODY
(H). See PICTURE 4B.
PICTURE 3A
Page 4 of 6
3.0/1108/TG
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 5: Unpack the
BEDDING SET (I). You
may launder the set be-
fore use if you wish,
and/or iron, press, or
steam it to remove
wrinkles. Machine wash
cold, gentle cycle only;
air dry or tumble dry
low or no heat. Iron on
lowest setting for poly/
cotton.
“Puzzle Piece” Fit
Locate the buttonholes
on the FABRIC LINER
and slip them over the
spools on the BASSI-
NET BODY (H).
Smooth the liner around
the sides and bottom in-
PICTURE 4A
PICTURE 3B
side the bassinet, and adjust it around the outside of the bassinet.
Put the SHEET onto the MATTRESS PAD (J) and place
the mattress pad into the bassinet.
Snap together the HOOD HOOP FRAME (K) as shown
in PICTURE 5. Stretch the fabric HOOD over the FRAME and
slip the elastic loops over the ends of the frame to hold the hood
in place. Snap the FRAME (K) onto the spools on the BASSI-
NET BODY (H).
Snap Straps
The bassinet is now ready for your baby! See PICTURE 6.
PICTURE 4B
PICTURE 6
Raised Lip
towards front
NOTE: Your bassinet
bedding may vary
from shown
PICTURE 5
Page 5 of 6
3.0/1108/TG
Download from Www.Somanuals.com. All Manuals Search And Download.
PICTURE 7
To use the bassinet as a Rocking Cradle,
loosen the caster knobs, rotate the casters
into the up position, and retighten the knobs.
See PICTURE 7.
TO CONVERT THE STAND TO A TOY BOX
PICTURE 8
STEPA: Remove the bedding, bassinet body,
hood, wooden dowels, and mesh basket, and
set them aside.
STEP B: Unscrew and remove all four of the
bolts holding the TOP RAILS and set aside
the screws, rails, and nylon snap straps.
STEP C: Insert the two larger SIDE PAN-
ELS (L) into the grooves on the bottom rails
with the white sides facing out.
STEP D: Re-attach the TOP RAILS using
the four screws making sure the side panels
are seated into the grooves.
STEP E: Place the bottom panel (L) inside
the stand resting on the bottom rails with the
white side facing up.
PICTURE 8
STEP F: Store the bassinet body, bedding
set, hood hoop frame, wooden dowels, mesh
basket, mattress pad, and nylon snap straps
for future use.
Page 6 of 6
3.0/1108/TG
Download from Www.Somanuals.com. All Manuals Search And Download.
|