Read all instructions BEFORE assembly and USE of product.
KEEP INSTRUCTIONS FOR FUTURE USE.
Model #8136BCC
DELUXE TREND NURSERY CENTER
Instruction Manual
Convenience through Innovation and thoughtful design
12.04
Download from Www.Somanuals.com. All Manuals Search And Download.
FOR THE SAFETY OF YOUR CHILD, PLEASE READ THE INSTRUCTIONS COMPLETELY
BEFORE ASSEMBLING THE PLAYARD, BASSINET AND CHANGING AREA
TO ASSEMBLE PLAYARD
CONTENTS (Fig. 1-1):
1 Playard
1 Mattress
1 Organizer
2 Leg extensions (1 Left,1 Right)
2 Leg extensions with wheels (1 Left, 1 Right)
1 Travel or Storage bag
Figure 1-1.
BEFORE YOU BEGIN: The Baby Trend Playard is designed so that,
when properly setup, the fabric of the playard places pressure on the 4
top rails making them nearly impossible to unlock. This safety feature
is activated when you push down on the playard floor to lock the bottom
rails. When setting up the playard, if you allow the bottom rails to lock
Figure 1.
before locking the top rails, the fabric pressure will not allow you to lock
the top rails. Please see (Fig. 3.) for the proper position of the bottom of
the playard when locking the top rails.
1. Unzip bag and remove Playard frame (Fig. 1). Undo the 3 Velcro straps
and set mattress aside (Fig. 2).
2. Turn the playard upside down. (Fig. 3). Push each leg extension into
the bottom of the leg until both sides of extension snap into place. (Fig.
Figure 2.
4). Check that the extension is firmly connected. Attach the wheels to
the playard with the axle and nut as shown in figure (Fig. 5). The brake
cluster on the wheel must face to the inside. The axle is inserted from
the outside to the inside. (Fig. 6). Check that the wheels are firmly
connected.
Leg extensions
3. Stand Playard on legs keeping feet of playard close together as shown in
(Fig. 7). Pull up on top rails until all rails “click” and “lock”.
* READ IMPORTANT: In order to continue, the handle in the center
of the floor of the Playard MUST remain raised in order for the
rail to lock (approx. 45.7 cm or 18 inches). The feet of the playard
should almost touch each other. All 4 bottom rails must be pointed
upward in order to LOCK top rails.
4. Push down on center of Playard floor until it is flat and locks into
position (Fig. 8). The center lock mechanism will lock automatically.
The center lock will rotate clockwise about 90 degrees as it locks.
Wheels
NOTE: Test rails to make sure they are locked. Push down on each
rail making sure they are rigid and in a set position.
Figure 3
3
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING: All top rails MUST be
straight and locked in position or child may
become entrapped and suffocate.
See figure 9 and 10.
5. Place mattress in Playard with padded side up (Fig. 11).
NOTE: DO NOT insert mattress if using bassinet feature. Go to
bassinet instructions.
Figure 5
Right
Left
6. Feed the 6 Velcro straps (found underneath the mattress), 3 on each
end of the mattress pad, through the slots on the bottom of the sides
of the Playard. Fasten the Velcro tabs to the underside of Playard to
prevent the mattress from moving (Fig. 12) (Fig. 13).
Insert
Insert
axle from
outside
axle from
outside
WARNING: To prevent child from
suffocating, Velcro straps MUST be secured
to underside of Playard.
Left
Figure 5
Right
7. Attach the organizer, to any side of the playard, by pushing the plastic
clips down over the top rail. (Fig. 14). The maximum weight capacity
of the organizer is 3 pounds.
8. To operate the brakes on the wheels, press downward on the brake
lever as shown in figure 15. To release, lift upward on the lever.
Playard assembly is now complete and ready to use.
Outside
Inside
Figure 6
Figure 9
Figure 7
Figure 8
Figure 10
Figure 11
Figure 12
Figure 13
Figure 14
Figure 15
4
Download from Www.Somanuals.com. All Manuals Search And Download.
FOLDING PLAYARD
1. Undo the 6 Velcro straps holding mattress from underneath Playard
floor. (If mattress is not used in the bassinet). Remove mattress and set
aside.
2. Grasp the center floor lock handle pushing down . Rotate the handle
counter-clockwise about 90 degrees and lift upward until handle is as
high as the top rails. Gather the four feet of the playard together so that
they nearly touch each other. See figure 1 and 2.
Rotate before
lifiting
Figure 1
NOTE: TOP RAILS OF THE PLAYARD ARE STILL IN THE
“LOCKED” POSITION.
3. Locate release button on the center of the bottom of each top rail. Lift
slightly while squeezing button until the rail clicks. Push down on rail
(while still holding release button in) until side forms a “U”. Repeat for
remaining sides (Fig. 3).
NOTE: If top rail(s) do not form the “U” completely do not force. Check
the floor of your Playard to make sure all bottom rails are unlocked and
pull up on middle handle of floor again. Repeat
step 3.
Figure 2
4. Pull up on handle in center of Playard (Fig. 4). Gather legs of Playard
together.
5. Wrap mattress around Playard frame with padded side facing in.
6. Secure the 3 Velcro straps by feeding through loops on end of mattress
and folding back onto itself (Fig. 5).
7. Place Playard in carry bag so handle comes through opening between
zippers and wheels come through opening in the end of bag.
Figure 3
WARNING: NEVER LEAVE INFANT IN
PRODUCT WITH SIDES DOWN.
Infant may roll into space between
pad and loose mesh side causing
suffocation.
Figure 5
Figure 4
5
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYARD BASSINET/CHANGING AREA
12.04
WARNING:FAILURE TO FOLLOW THESE WARNINGS
AND THE ASSEMBLY INSTRUCTIONS COULD RESULT
IN SERIOUS INJURY OR DEATH FROM ENTRAPMENT,
STRANGULATION, SUFFOCATION, ETC.
• To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their back
to sleep, unless otherwise advised by your physician.
•
Always provide the supervision necessary for the continued safety of your child. When used
for playing, never leave child unattended.
•
•
•
•
•
Adult supervision is always necessary when using your bassinet.
Your playard, including side rails and bottom pad, must be fully erected prior to use.
Top rails must be locked.
Bottom rails must be in flat, locked position.
SUFFOCATION HAZARD: To help prevent suffocation from entrapment, use only the
mattress provided by BabyTrend®. Neveruse additional mattress orpadding. Neveruse plastic
shipping bags or other plastic film as mattress covers not sold and intended for that purpose.
Avoid SUFFOCATION HAZARD caused by a loose sheet. A fitted sheet is recommended. The
fitted sheet must fit the mattress tightly.
•
STRANGULATION HAZARD: DO NOT place items with a string around child’s neck, such
as hood strings or pacifier cords. DO NOT suspend string over bassinet or attach strings to
toys.
•
•
DO NOT add padding or other objects inside your bassinet which will permit a child to climb
out.
To prevent your child from falling out of the bassinet discontinue using your bassinet when
your child is too active, able to climb out, weighs over 15 lbs.. (6.8 kgs.), or is over 4 months
old.
•
•
•
•
•
•
DO NOT use a water mattress with this bassinet.
Use your bassinet with only one child at a time.
Keep bassinet away from stoves, heaters, campfires and other hazards.
Never place a child under the bassinet.
DO NOT store the bassinet in the playard.
The bassinet must be fully assembled and installed, including top rails and bottom pad,
before using.
•
Before each use or assembly, inspect the playard and bassinet / changing area for damaged
hardware, loose joints, missing parts or sharp edges. DO NOT use playard or bassinet if
any parts are missing or broken. Call our Customer Service department at (800) 328-7363 for
replacement parts.
•
To protect your child from falls and other injuries: always use safety belt when child is on the
changing table, always stay within arm’s reach of your child when using the changing table,
never leave child unattended.
Baby Trend, Inc.
1567 S. Campus Ave.
Ontario, CA 91761
Customer Service Hot Line:
(800) 328-7363
8:00 A.M. to 4:30 P.M. Pacific Standard Time
6
Download from Www.Somanuals.com. All Manuals Search And Download.
TO ASSEMBLE YOUR BASSINET
NOTE: Playard MUST be in a locked set-up position before
installing and using the bassinet feature.
CONTENTS (Fig. 1):
2 Right corner supports
2 Left corner supports
1 Nylon bassinet insert
2 Long metal tubes
2 Medium metal tubes
2 Short metal tubes
ASSEMBLY
Figure 1
Figure 2
1. Insert 1 short tube into a medium tube lining up the snap button and
the hole opening. Make sure the snap buttons are exactly fitted into
the holes (Fig. 2). Repeat for the second set of tubes.
2. Unroll the nylon bassinet fabric. Insert one set of the connected
tubes into each long side of the bassinet sleeve (Fig. 3).
NOTE: The printed warning label should be facing toward the
inside of the bassinet and is readable.
3. Insert 1 long tube into the short side of the bassinet sleeve. Repeat
for remaining side.
4. Slide the corner supports onto the ends of each tube (Fig. 4). The
corner support with a hole is used for the mobile. Place this corner
support on the end opposite the changing table.
The bassinet canopy is secured to the bassinet with snaps on the
outside sleeve. Snap both on the ends of the canopy to the sleeve as
shown in (Fig. 4a). The rear section of the canopy is connected to
the bassinet sleeve as shown in (Fig. 4b).
Figure 3.
5. Place assembled bassinet onto the Playard. Push down each of the
corner supports (Fig. 5).
NOTE: The corner supports are designed to rest on long side of
Playard (40 in. rail) and wrap around the short side of the Playard
top corner pieces.
Figure 4.
6. Place the Playard mattress into the bassinet with the padded side
facing up (Fig. 6).
bassinet
snap
Figure 5.
Figure 6.
Figure 4a.
Figure 4b.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
TO ASSEMBLE CHANGING AREA
CONTENTS (Fig. 1):
•
•
•
2 Long curved bars
2 Short bars with connector knobs
1 Changing area fabric
Figure 1
WARNING:
Avoid serious injury or death:
• Always use restraint belt to prevent falls (Fig.
1-1).
• Use changer with infant who’s weight is less
than 18 lbs (8.2 kg ) and is less than
25 inches (63.5 cm) tall.
Figure 2
• Discontinue use of changer if infant can push
up on hands and knees or sit unassisted.
• DO NOT carry changer with infant in it.
WARNING: Strangulation Hazard
Child can lift the changing table and get
neck trapped between the changing table
frame and the play yard frame. Never leave
the changing table in place when the child is
in the bassinet or the play yard. Always flip
changer to the outside when not in use.
Holes face
down
Figure 3
ASSEMBLY
Figure 4.
1. Connect the two Long Curved Bars together as shown in figure 2.
2. Insert the assembled Curved Bars into the Changing Area Fabric
such that the holes in the ends of the Curved Bars face downward
as shown in Figure 3.
3. Slide the Curved Bars around inside the sleeve of the Changing
Area Fabric.
4. Connect the Short Bars with Connector Knobs to the Curved
Bars as shown in figure 4. When assembling the Short Bars with
Connector Knobs make sure that the knobs will be facing inward
when assembled and the snap buttons are facing downward.
Completed assembly
Figure 5.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE: Short bar with connector knobs should be facing
inward.
5. Place connector knob prongs into holes located on corner pieces
of Playard (Fig. 5).
6. Turn connector knobs counter clockwise to lock (Fig. 6).
7. Flip changing area to inside of Playard (Fig.7).
8. Snap flap from changing area to side of Playard (Fig. 8).
9 Check that changing area is secure before using.
Figure 5.
Figure 6.
Figure 7.
Figure 8.
REMOVALAND FOLDING CHANGING AREA
ASSEMBLY
1. Flip changing area to the outside of the Playard. Unsnap fabric flap
of changing area from Playard.
2. Twist connector knobs clockwise to unlock (Fig. 1).
3. Remove changing area from Playard (Fig. 2).
4. Disconnect the short bars from the curved bar by pressing on the
snap buttons and pulling apart. Remove curved bar from changing
area sleeve.
Figure 1.
The changing area is now ready for storage.
Figure 2.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOVAL OF BASSINET
ASSEMBLY
1. Remove mattress from bassinet (Fig.1).
2. Lift bassinet out of Playard (Fig. 2).
3. Remove corner pieces and slide metal tubes from fabric sleeves
(Fig. 3).
4. Separate tubes by pressing on snap buttons and pull apart.
The bassinet is now ready for storage.
NOTE: Store bassinet and changing area with folded Play yard
in carry bag.
Figure 1
Figure 3
Figure 2
TO REMOVE CANOPY
REMOVAL OF CANOPY
To remove the bassinet canopy, unsnap the ends of the canopy from
the side of the bassinet. The canopy can be stored in the travel bag.
STOP
IF YOU EXPERIENCE ANY DIFFICULTY IN USING THIS PRODUCT, PLEASE
CONTACT OUR CUSTOMER SERVICE DEPARTMENT AT (800) 328-7363 BETWEEN
THE HOURS OF 8:00 A.M. AND 4:30 P.M. PACIFIC COAST TIME FOR ASSISTANCE.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|