AXXESS STEERING WHEEL CONTROL INTERFACE
INSTALLATION
MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
A brief overview of the ASWC interface and wire harness:
On the top of the ASWC interface there are three points of interest:
1) The Programming led – this will flash rapidly when in auto detect mode, flashes slowly in manual
programming mode
2) The Reset button – Hold down button more then 2 seconds but less then 10 seconds to start auto
detect mode; hold down longer then 10 seconds to start manual programming mode
3) The slide cover for the USB update port – open this up to reveal the USB update port. Using the
USB-CAB update cable and the Axxess website you can make sure you always have the latest,
updated inventory.
USB PORT COVER
RESET BUTTON
PROGRAMMING LED
Below are the wire colors of the ASWC. Please go to the Axxess website (www.axxessinterface.com)
for detailed information on your specific vehicle and what color wire(s) to use on the ASWC.
Pin 1 – Pink
Pin 7 – Blue/Pink
Pin 2 – White/Green
Pin 3 – Orange/Green
Pin 4 – Green/Orange
Pin 5 – Gray/Red
Pin 6 – Black
Pin 8 – Black/Green
Pin 9 – Red (Tip of 3.5mm connector)
Pin 10 – White (Ring of 3.5mm connector)
Pin 11 – Gray/Blue
Pin 12 – Red
PIN PIN PIN PIN PIN PIN
12 11 10
9
8
7
PIN PIN PIN PIN PIN PIN
6
5
4
3
2
1
Wire Insertion View
3
axxessinterface.com
800.221.0932
Download from Www.Somanuals.com. All Manuals Search And Download.
The Installation
Once you have collected the information or printed out the information sheet on your particular ve-
So here we go:
1) Connect the Black wire of the ASWC (pin 6) to ground. You may use the same grounding point as
the aftermarket radio.
2) Connect the Red wire of the ASWC (pin 12) to a 12 volt accessory wire, one that turns on and off
with the ignition key.
3) Locate the correct SWC wire(s) in the vehicles radio or secondary harness as described in the
vehicle information sheet found in the Axxess website. Connect the correct wire color(s) from the
ASWC to the vehicles steering wheel control wire(s) in the vehicle.
We recommend that the wires are soldered for the best and most secure connection. T-Taps are not
recommended due to the higher chance of an intermitted connection (this means you Zack).
4) If you are using an Eclipse or Kenwood radio, plug the female 3.5mm connector with the Brown
and Brown/White wires into the male 3.5mm connector of the ASWC harness.
* For Kenwood radios: Connect the Kenwood SWC wire (normally Blue/Yellow) to the Brown
wire of the ASWC. Isolate and tape the Brown/White wire, it will not be used.
* For Eclipse radios: Connect the Eclipse SWC wires (Normally Brown and Brown/Black) to the
Brown and Brown/White wires of the ASWC. Brown goes to Brown and Brown/White goes to Brown/
Black.
5) For all other radios, plug in the male 3.5mm connector of the ASWC into the back of the
aftermarket radio, designated for an external SWC control interface. Please refer to the aftermarket
radios manual if you are in doubt where the 3.5mm connector of the ASWC goes.
Once all connections have been made, plug in the aftermarket radio if not done already.
Programming the ASWC
The ASWC can be programmed in two ways; it can do it by itself in Auto Detect Mode or it can be
manually programmed. We will start with the Auto Detect Mode first:
Auto Detect Mode:
The ASWC has the ability to auto detect certain vehicles and to know what aftermarket radio it is
your vehicle would be auto detected and what action, if any, is required by you for this process to take
place.
4
axxessinterface.com
800.221.0932
Download from Www.Somanuals.com. All Manuals Search And Download.
For the Auto Detect feature to work there are 3 possible actions, however only one action will be re-
quired by you depending on your vehicle:
1) Turn the ignition on and no other action is required.
2) Turn the ignition on, press and hold down the Volume Up button on the steering wheel.
Or
3) Turn the ignition on, press and release the Volume Up button repeatedly on the steering
wheel.
Like we said before, only one of these actions will need to be done depending on your vehicle for the
auto detect feature to work. Please refer to the vehicle info sheet in the Axxess website.
These are the steps for the Auto Detect Mode:
1) Complete connections to the vehicle and the aftermarket radio.
* If this is the first time the ASWC is being installed in a vehicle:
2) Turn the ignition on; the led will start flashing rapidly which means the ASWC is looking for the
vehicle and the radio.
3) Perform action required for your particular vehicle as noted in the vehicle info sheet.
4) After a couple of seconds the led should stop flashing and not light up for 2 seconds. At this point
do not push any buttons.
5) After the 2 seconds there will be a series of 7 flashes, some short and some long. Make a note of
which flashes were long for this may be needed later.
6) The led will pause for another 2 seconds then flash up to 9 times. Again make a note of how many
flashes.
7) This is the end of the auto detection stage. If the ASWC detected the vehicle and the radio
successfully the led will light up solid red.
8) Make sure the steering wheel control buttons function correctly in the vehicle and enjoy your radio.
So what if the led does not light up solid red? Check out troubleshooting section below.
5
axxessinterface.com
800.221.0932
Download from Www.Somanuals.com. All Manuals Search And Download.
* If the ASWC was installed in a vehicle before:
2) Turn the ignition on, the led will flash slowly
3) Hold down the reset button for more then 2 seconds but less then 10 seconds, the led will start
flashing rapidly
4) Perform action required for your particular vehicle as noted in the vehicle info sheet
5) After a couple of seconds the led should stop flashing and not light up for 2 seconds. At this point
do not push any buttons.
6) After the 2 seconds there will be a series of 7 flashes, some short and some long.
7) The led will pause another 2 seconds then a series of 9 flashes.
8) This is the end of the auto detection stage. If the ASWC detected the vehicle and the radio
successfully the led will light up solid red.
9) Make sure the steering wheel control buttons function correctly in the vehicle and enjoy your radio.
So what if the led does not light up solid red or the steering wheel controls is not working correctly
with the aftermarket radio?
Check out troubleshooting section right below.
Troubleshooting the Auto Detect Mode
So you tried the auto detect feature and at the end the led did not stay on solid red, it started flashing.
That means the ASWC did not detect the vehicle. Follow these couple steps to determine what hap-
pened:
First some basic steps:
1) Verify that you have 12 volt accessory and a good ground to the ASWC.
2) Verify with the vehicle information sheet on the Axxess website that you connected the correct
steering wheel control wires in the vehicle to the correct wire(s) on the ASWC.
3) Verify that the 3.5mm connector is connected to your radio securely and in the correct location.
4) If using the female 3.5mm connector on an Eclipse or Kenwood radio, verify that the radio’s SWC
wire is connected to the correct wire on the ASWC.
6
axxessinterface.com
800.221.0932
Download from Www.Somanuals.com. All Manuals Search And Download.
Once all the information above has been verified and correct, refer back to the 2 sets of led flashes
during the auto detect sequence. Here is what the flashes stand for:
LED Feedback
The 1st series of led flashes represent the wire(s) that are connected to the vehicle from the ASWC.
Short flashes represent the steering wheel control wire(s) that are not connected to the vehicle from
the ASWC
Long flashes represent the wire(s) that are connected to the vehicle
1st led flash is pin #2 (White/Green) on the ASWC
2nd led flash is pin #3 (Orange/Green) on the ASWC
3rd led flash is pin #4 (Green/Orange) on the ASWC
4th led flash is pin #5 (Gray/Red) on the ASWC
5th led flash is pin #8 (Black/Green) on the ASWC
6th led flash is pin #11 (Gray/Blue) on the ASWC
7th led flash is pin #1 (Pink) on the ASWC
If during the auto detect sequence there was no long led flash, just short ones, the ASWC was not
connected to the correct wire in the vehicle or the incorrect wire was used on the ASWC. Double
check connections and the vehicle information sheet to verify that you have the correct wires con-
nected.
The 2nd set of led flashes represents what brand radio the ASWC believes it is connected to. Each
flash is for a different radio manufacturer.
1st led flash is for Eclipse
2nd led flash is for Kenwood**
3rd led flash is for Clarion
4th led flash is for Sony and Dual
5th led flash is for JVC
6th led flash is for Pioneer and Jensen
7th led flash is for Alpine*
8th led flash is for Visteon
9th led flash is for Valor
* Note: If the ASWC flashes 7 times and you do not have an Alpine radio connected to it that means
that the ASWC did not see any radio connected. Verify the 3.5mm connector is connected to the
SWC input on the radio.
** Note: The following three models, DNX9960, DNX7160, and DDX896, need a 10k to 12k ohm re-
sistor between the Blue/Yellow of the Kenwood and the Brown wire of the female 3.5 during program-
ming. After programming remove the resistor and reconnect the Blue/Yellow and brown wire.
7
axxessinterface.com
800.221.0932
Download from Www.Somanuals.com. All Manuals Search And Download.
Manual Programming/SWC Button Reassignment:
If your vehicle is not listed for auto detection by the ASWC on the Axxess website most vehicles can
still be manually programmed to the ASWC by following these steps:
* Note: Not every radio will have all the possible swc commands on the steering wheel. Aftermarket
radios that do not have Bluetooth will not recognize the PTT (Push To Talk) or On Hook / Off Hook
commands, however those buttons can be manually programmed to do other commands. Please
refer to the radios owners’ manual or wireless remote for specific commands the radio will recognize.
1) Complete connections to the vehicle and the aftermarket radio, making sure the 3.5mm connector
is connected.
* If this is the first time the ASWC is being installed in a vehicle:
2) Turn the ignition on; the led will start flashing rapidly
3) After 10 seconds the ASWC will go into the LED feedback mode. After the series of led flashes the
led will stay in a slow constant flash state.
Or
* If the ASWC has been in a vehicle before:
2) Press and hold the reset button down for more then 10 seconds.
3) After the 10 seconds the led will begin a slow constant flash.
4) At this point press and hold the Volume Up button on the steering wheel for 7 seconds until the led
goes solid red. Now release the Volume Up button and the led goes off. Volume Up has now been
programmed.
5) Now press and hold the Volume Down button until the led goes solid red. Release the Volume
Down button and the led goes off. Volume Down has now been programmed.
6) At this point press and hold the next button on the steering wheel that corresponds with the
programming list (see below). The chart below shows in what order the steering wheel control
buttons need to be programmed in.
If the next function on the list is not on the steering wheel press and hold the Volume Up button for 1
second till the led comes on then release the button. This tells the ASWC that the function is not avail-
able and moves on to the next function.
8
axxessinterface.com
800.221.0932
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Volume Up
2. Volume Down
3. Seek Up/Next
4. Seek Down/Prev
5. Source/Mode
6. Mute
7. Preset Up
8. Preset Down
9. Power
10. Band
11. Play/Enter
12. PTT (Push To Talk)
13. On Hook
14. Off Hook
15. Fan Up
16. Fan Down
17. Temp Up
18. Temp Down
* Note: Remember not all radios will have all these commands. Please refer to the radios’ owners
manual for specific commands recognized by the radio.
7) You can end this half of the programming in 2 ways:
1) After the last button is programmed on your steering wheel (you do not have to go through
the whole list), hold down the Volume Up button for at least 10 seconds. The led will go into
the slow constant blink mode.
Or
2) After the 18th button is programmed or skipped the led will go back to the slow constant blink
mode.
* If at any time you get lost or mess up hold down the reset button on the ASWC for more then 10
seconds. This will restart the manual programming. Go back to step #4 and start again.
At this point you will now be in the Radio Identification mode
8) Press and hold the Volume Down button for 5 seconds till the led starts to flash quickly.
9) Release the Volume Down button.
9
axxessinterface.com
800.221.0932
Download from Www.Somanuals.com. All Manuals Search And Download.
10) After 4 seconds of the led flashing quickly the led will go out for 2 seconds.
11) Then the led will flash, up to 9 times, depending on what radio the ASWC thinks it’s connected to.
Here are the led blinks and which radio they represent:
1st led flash is for Eclipse
2nd led flash is for Kenwood
3rd led flash is for Clarion
4th led flash is for Sony and Dual
5th led flash is for JVC
6th led flash is for Pioneer and Jensen
7th led flash is for Alpine*
8th led flash is for Visteon
9th led flash is for Valor
* Note: If the ASWC flashes 7 times and you do not have an Alpine radio connected to it that means
that the ASWC did not see any radio connected. Verify the 3.5mm connector is connected to the
SWC input on the radio.
12) Make sure the number of flashes match what radio you have installed.
13) If the led flashes match the radio then hold down the Volume Down button until the led goes solid
red.
14) Programming for the vehicle and the radio is now complete. Test out the steering wheel control
functions to make sure it works correctly.
If the led flashes do not match the radio you have connected, you must manually program the ASWC
to tell it what radio it is connected to.
1) To manually program the aftermarket radio, press and hold the Volume Up button on the steering
wheel control until the led goes solid red, then release Volume Up.
2) At this point Eclipse is programmed.
If you are using an Eclipse radio go to step 3.
If you are using a different radio go to step 4.
3) Press and hold Volume Down for 5 seconds. The led will flash once then go solid red indicating the
programming has finished. Go enjoy your radio.
10
axxessinterface.com
800.221.0932
Download from Www.Somanuals.com. All Manuals Search And Download.
4) If you have a different radio then Eclipse, press the Volume Up button again till the led goes solid
red, then release Volume Up. You have now programmed Kenwood.
5) Here is the chart to show how many presses of the Volume Up button is needed for which radio
you are trying to program:
1st led flash is for Eclipse
2nd led flash is for Kenwood
3rd led flash is for Clarion
4th led flash is for Sony and Dual
5th led flash is for JVC
6th led flash is for Pioneer and Jensen
7th led flash is for Alpine*
8th led flash is for Visteon
9th led flash is for Valor
* Note: If the ASWC flashes 7 times and you do not have an Alpine radio connected to it that means
that the ASWC did not see any radio connected. Verify the 3.5mm connector is connected to the
SWC input on the radio.
6) Once the radio manufacturer has been selected hold Volume Down for at least 5 seconds. The
led will flash the number of times which radio was selected then the led will remain on to indicate
the ASCW has finished programming.
7) Go enjoy your radio.
Remapping the SWC Buttons
Let’s say you have the ASWC programmed to your vehicle and your radio and you want to change
the button assignment for the steering wheel controls. For instance you would like Seek Up to be
Mute.
This process is the same as manually programming the ASWC (please refer to the Manual Program-
ming section) with a couple of notes:
• The ASWC must have detected the vehicle and radio it is attached to before you can remap
any buttons.
• You can only start the remapping of the steering wheel controls process within the first 20 seconds
of turning the ignition key on. If you wait longer then the 20 seconds you will have to turn the
ignition off then back on again.
• Within the first 20 seconds if any button other then Volume Up or Volume Down is pushed, the
remapping process will stop.
• If during the remapping process no button is pushed for 30 seconds the remapping process is
aborted and the original settings are reset.
11
axxessinterface.com
800.221.0932
Download from Www.Somanuals.com. All Manuals Search And Download.
So let’s begin the remapping process:
1) Ideally having the ASWC visible is recommended since you can see the led flashes to confirm
button recognition.
2) Turning off the radio is recommended
3) Within the first 20 seconds of turning the ignition on, press and hold down the Volume Up button
for at least 25 seconds.
4) The led will light up solid red. Release Volume Up and the led will go out. Volume Up has now
been programmed.
5) Follow the list below in order however pushing the steering wheel control button you want for the
function below. If you want to skip a command press the Volume Up on the steering wheel, this
will tell the ASWC to skip the command and go to the next one.
1. Volume Up
2. Volume Down
3. Seek Up/Next
4. Seek Down/Prev
5. Source/Mode
6. Mute
7. Preset Up
8. Preset Down
9. Power
10. Band
11. Play/Enter
12. PTT (Push To Talk)
13. On Hook
14. Off Hook
15. Fan Up
16. Fan Down
17. Temp Up
18. Temp Down
* Note: Remember not all radios will have all these commands. Please refer to the radios’ owners
manual for specific commands recognized by the radio.
For instance the next command to be mapped is the Volume Down command. Let’s say you want the
Mode button on your steering wheel to be the Volume Down command. Hold down the Mode but-
ton till the led lights up solid red, and then release it. Now your Mode button on the steering wheel is
Volume Down.
12
axxessinterface.com
800.221.0932
Download from Www.Somanuals.com. All Manuals Search And Download.
6) After the last button is programmed on your steering wheel (you do not have to go through the
whole list), hold down the Volume Up button for at least 10 seconds then the led will go out.
Or
After the 18th button is programmed or skipped the led will go out and the remapping is completed.
If for any reason after remapping the steering wheel controls you want to go back to the original steer-
ing wheel control settings, follow these steps:
1) Within the first 20 seconds of turning the ignition on. Press and hold down the original Volume
Down button (not the Volume Down button you just remapped) for at least 25 seconds.
2) The led will turn on then release the Volume Down button and the led will turn off.
3) The original steering wheel control settings will be restored.
13
axxessinterface.com
800.221.0932
Download from Www.Somanuals.com. All Manuals Search And Download.
|